| /* | |
| * linux/drivers/ide/pci/atiixp.c Version 0.01-bart2 Feb. 26, 2004 | |
| * | |
| * Copyright (C) 2003 ATI Inc. <hyu@ati.com> | |
| * Copyright (C) 2004 Bartlomiej Zolnierkiewicz | |
| * | |
| */ | |
| #include <linux/types.h> | |
| #include <linux/module.h> | |
| #include <linux/kernel.h> | |
| #include <linux/ioport.h> | |
| #include <linux/pci.h> | |
| #include <linux/hdreg.h> | |
| #include <linux/ide.h> | |
| #include <linux/delay.h> | |
| #include <linux/init.h> | |
| #include <asm/io.h> | |
| #define ATIIXP_IDE_PIO_TIMING 0x40 | |
| #define ATIIXP_IDE_MDMA_TIMING 0x44 | |
| #define ATIIXP_IDE_PIO_CONTROL 0x48 | |
| #define ATIIXP_IDE_PIO_MODE 0x4a | |
| #define ATIIXP_IDE_UDMA_CONTROL 0x54 | |
| #define ATIIXP_IDE_UDMA_MODE 0x56 | |
| typedef struct { | |
| u8 command_width; | |
| u8 recover_width; | |
| } atiixp_ide_timing; | |
| static atiixp_ide_timing pio_timing[] = { | |
| { 0x05, 0x0d }, | |
| { 0x04, 0x07 }, | |
| { 0x03, 0x04 }, | |
| { 0x02, 0x02 }, | |
| { 0x02, 0x00 }, | |
| }; | |
| static atiixp_ide_timing mdma_timing[] = { | |
| { 0x07, 0x07 }, | |
| { 0x02, 0x01 }, | |
| { 0x02, 0x00 }, | |
| }; | |
| static int save_mdma_mode[4]; | |
| /** | |
| * atiixp_ratemask - compute rate mask for ATIIXP IDE | |
| * @drive: IDE drive to compute for | |
| * | |
| * Returns the available modes for the ATIIXP IDE controller. | |
| */ | |
| static u8 atiixp_ratemask(ide_drive_t *drive) | |
| { | |
| u8 mode = 3; | |
| if (!eighty_ninty_three(drive)) | |
| mode = min(mode, (u8)1); | |
| return mode; | |
| } | |
| /** | |
| * atiixp_dma_2_pio - return the PIO mode matching DMA | |
| * @xfer_rate: transfer speed | |
| * | |
| * Returns the nearest equivalent PIO timing for the PIO or DMA | |
| * mode requested by the controller. | |
| */ | |
| static u8 atiixp_dma_2_pio(u8 xfer_rate) { | |
| switch(xfer_rate) { | |
| case XFER_UDMA_6: | |
| case XFER_UDMA_5: | |
| case XFER_UDMA_4: | |
| case XFER_UDMA_3: | |
| case XFER_UDMA_2: | |
| case XFER_UDMA_1: | |
| case XFER_UDMA_0: | |
| case XFER_MW_DMA_2: | |
| case XFER_PIO_4: | |
| return 4; | |
| case XFER_MW_DMA_1: | |
| case XFER_PIO_3: | |
| return 3; | |
| case XFER_SW_DMA_2: | |
| case XFER_PIO_2: | |
| return 2; | |
| case XFER_MW_DMA_0: | |
| case XFER_SW_DMA_1: | |
| case XFER_SW_DMA_0: | |
| case XFER_PIO_1: | |
| case XFER_PIO_0: | |
| case XFER_PIO_SLOW: | |
| default: | |
| return 0; | |
| } | |
| } | |
| static int atiixp_ide_dma_host_on(ide_drive_t *drive) | |
| { | |
| struct pci_dev *dev = drive->hwif->pci_dev; | |
| unsigned long flags; | |
| u16 tmp16; | |
| spin_lock_irqsave(&ide_lock, flags); | |
| pci_read_config_word(dev, ATIIXP_IDE_UDMA_CONTROL, &tmp16); | |
| if (save_mdma_mode[drive->dn]) | |
| tmp16 &= ~(1 << drive->dn); | |
| else | |
| tmp16 |= (1 << drive->dn); | |
| pci_write_config_word(dev, ATIIXP_IDE_UDMA_CONTROL, tmp16); | |
| spin_unlock_irqrestore(&ide_lock, flags); | |
| return __ide_dma_host_on(drive); | |
| } | |
| static int atiixp_ide_dma_host_off(ide_drive_t *drive) | |
| { | |
| struct pci_dev *dev = drive->hwif->pci_dev; | |
| unsigned long flags; | |
| u16 tmp16; | |
| spin_lock_irqsave(&ide_lock, flags); | |
| pci_read_config_word(dev, ATIIXP_IDE_UDMA_CONTROL, &tmp16); | |
| tmp16 &= ~(1 << drive->dn); | |
| pci_write_config_word(dev, ATIIXP_IDE_UDMA_CONTROL, tmp16); | |
| spin_unlock_irqrestore(&ide_lock, flags); | |
| return __ide_dma_host_off(drive); | |
| } | |
| /** | |
| * atiixp_tune_drive - tune a drive attached to a ATIIXP | |
| * @drive: drive to tune | |
| * @pio: desired PIO mode | |
| * | |
| * Set the interface PIO mode. | |
| */ | |
| static void atiixp_tuneproc(ide_drive_t *drive, u8 pio) | |
| { | |
| struct pci_dev *dev = drive->hwif->pci_dev; | |
| unsigned long flags; | |
| int timing_shift = (drive->dn & 2) ? 16 : 0 + (drive->dn & 1) ? 0 : 8; | |
| u32 pio_timing_data; | |
| u16 pio_mode_data; | |
| spin_lock_irqsave(&ide_lock, flags); | |
| pci_read_config_word(dev, ATIIXP_IDE_PIO_MODE, &pio_mode_data); | |
| pio_mode_data &= ~(0x07 << (drive->dn * 4)); | |
| pio_mode_data |= (pio << (drive->dn * 4)); | |
| pci_write_config_word(dev, ATIIXP_IDE_PIO_MODE, pio_mode_data); | |
| pci_read_config_dword(dev, ATIIXP_IDE_PIO_TIMING, &pio_timing_data); | |
| pio_timing_data &= ~(0xff << timing_shift); | |
| pio_timing_data |= (pio_timing[pio].recover_width << timing_shift) | | |
| (pio_timing[pio].command_width << (timing_shift + 4)); | |
| pci_write_config_dword(dev, ATIIXP_IDE_PIO_TIMING, pio_timing_data); | |
| spin_unlock_irqrestore(&ide_lock, flags); | |
| } | |
| /** | |
| * atiixp_tune_chipset - tune a ATIIXP interface | |
| * @drive: IDE drive to tune | |
| * @xferspeed: speed to configure | |
| * | |
| * Set a ATIIXP interface channel to the desired speeds. This involves | |
| * requires the right timing data into the ATIIXP configuration space | |
| * then setting the drive parameters appropriately | |
| */ | |
| static int atiixp_speedproc(ide_drive_t *drive, u8 xferspeed) | |
| { | |
| struct pci_dev *dev = drive->hwif->pci_dev; | |
| unsigned long flags; | |
| int timing_shift = (drive->dn & 2) ? 16 : 0 + (drive->dn & 1) ? 0 : 8; | |
| u32 tmp32; | |
| u16 tmp16; | |
| u8 speed, pio; | |
| speed = ide_rate_filter(atiixp_ratemask(drive), xferspeed); | |
| spin_lock_irqsave(&ide_lock, flags); | |
| save_mdma_mode[drive->dn] = 0; | |
| if (speed >= XFER_UDMA_0) { | |
| pci_read_config_word(dev, ATIIXP_IDE_UDMA_MODE, &tmp16); | |
| tmp16 &= ~(0x07 << (drive->dn * 4)); | |
| tmp16 |= ((speed & 0x07) << (drive->dn * 4)); | |
| pci_write_config_word(dev, ATIIXP_IDE_UDMA_MODE, tmp16); | |
| } else { | |
| if ((speed >= XFER_MW_DMA_0) && (speed <= XFER_MW_DMA_2)) { | |
| save_mdma_mode[drive->dn] = speed; | |
| pci_read_config_dword(dev, ATIIXP_IDE_MDMA_TIMING, &tmp32); | |
| tmp32 &= ~(0xff << timing_shift); | |
| tmp32 |= (mdma_timing[speed & 0x03].recover_width << timing_shift) | | |
| (mdma_timing[speed & 0x03].command_width << (timing_shift + 4)); | |
| pci_write_config_dword(dev, ATIIXP_IDE_MDMA_TIMING, tmp32); | |
| } | |
| } | |
| spin_unlock_irqrestore(&ide_lock, flags); | |
| if (speed >= XFER_SW_DMA_0) | |
| pio = atiixp_dma_2_pio(speed); | |
| else | |
| pio = speed - XFER_PIO_0; | |
| atiixp_tuneproc(drive, pio); | |
| return ide_config_drive_speed(drive, speed); | |
| } | |
| /** | |
| * atiixp_config_drive_for_dma - configure drive for DMA | |
| * @drive: IDE drive to configure | |
| * | |
| * Set up a ATIIXP interface channel for the best available speed. | |
| * We prefer UDMA if it is available and then MWDMA. If DMA is | |
| * not available we switch to PIO and return 0. | |
| */ | |
| static int atiixp_config_drive_for_dma(ide_drive_t *drive) | |
| { | |
| u8 speed = ide_dma_speed(drive, atiixp_ratemask(drive)); | |
| /* If no DMA speed was available then disable DMA and use PIO. */ | |
| if (!speed) { | |
| u8 tspeed = ide_get_best_pio_mode(drive, 255, 5, NULL); | |
| speed = atiixp_dma_2_pio(XFER_PIO_0 + tspeed) + XFER_PIO_0; | |
| } | |
| (void) atiixp_speedproc(drive, speed); | |
| return ide_dma_enable(drive); | |
| } | |
| /** | |
| * atiixp_dma_check - set up an IDE device | |
| * @drive: IDE drive to configure | |
| * | |
| * Set up the ATIIXP interface for the best available speed on this | |
| * interface, preferring DMA to PIO. | |
| */ | |
| static int atiixp_dma_check(ide_drive_t *drive) | |
| { | |
| ide_hwif_t *hwif = HWIF(drive); | |
| struct hd_driveid *id = drive->id; | |
| u8 tspeed, speed; | |
| drive->init_speed = 0; | |
| if ((id->capability & 1) && drive->autodma) { | |
| if (ide_use_dma(drive)) { | |
| if (atiixp_config_drive_for_dma(drive)) | |
| return hwif->ide_dma_on(drive); | |
| } | |
| goto fast_ata_pio; | |
| } else if ((id->capability & 8) || (id->field_valid & 2)) { | |
| fast_ata_pio: | |
| tspeed = ide_get_best_pio_mode(drive, 255, 5, NULL); | |
| speed = atiixp_dma_2_pio(XFER_PIO_0 + tspeed) + XFER_PIO_0; | |
| hwif->speedproc(drive, speed); | |
| return hwif->ide_dma_off_quietly(drive); | |
| } | |
| /* IORDY not supported */ | |
| return 0; | |
| } | |
| /** | |
| * init_hwif_atiixp - fill in the hwif for the ATIIXP | |
| * @hwif: IDE interface | |
| * | |
| * Set up the ide_hwif_t for the ATIIXP interface according to the | |
| * capabilities of the hardware. | |
| */ | |
| static void __devinit init_hwif_atiixp(ide_hwif_t *hwif) | |
| { | |
| if (!hwif->irq) | |
| hwif->irq = hwif->channel ? 15 : 14; | |
| hwif->autodma = 0; | |
| hwif->tuneproc = &atiixp_tuneproc; | |
| hwif->speedproc = &atiixp_speedproc; | |
| hwif->drives[0].autotune = 1; | |
| hwif->drives[1].autotune = 1; | |
| if (!hwif->dma_base) | |
| return; | |
| hwif->atapi_dma = 1; | |
| hwif->ultra_mask = 0x3f; | |
| hwif->mwdma_mask = 0x06; | |
| hwif->swdma_mask = 0x04; | |
| /* FIXME: proper cable detection needed */ | |
| hwif->udma_four = 1; | |
| hwif->ide_dma_host_on = &atiixp_ide_dma_host_on; | |
| hwif->ide_dma_host_off = &atiixp_ide_dma_host_off; | |
| hwif->ide_dma_check = &atiixp_dma_check; | |
| if (!noautodma) | |
| hwif->autodma = 1; | |
| hwif->drives[1].autodma = hwif->autodma; | |
| hwif->drives[0].autodma = hwif->autodma; | |
| } | |
| static void __devinit init_hwif_sb600_legacy(ide_hwif_t *hwif) | |
| { | |
| hwif->atapi_dma = 1; | |
| hwif->ultra_mask = 0x7f; | |
| hwif->mwdma_mask = 0x07; | |
| hwif->swdma_mask = 0x07; | |
| if (!noautodma) | |
| hwif->autodma = 1; | |
| hwif->drives[0].autodma = hwif->autodma; | |
| hwif->drives[1].autodma = hwif->autodma; | |
| } | |
| static ide_pci_device_t atiixp_pci_info[] __devinitdata = { | |
| { /* 0 */ | |
| .name = "ATIIXP", | |
| .init_hwif = init_hwif_atiixp, | |
| .channels = 2, | |
| .autodma = AUTODMA, | |
| .enablebits = {{0x48,0x01,0x00}, {0x48,0x08,0x00}}, | |
| .bootable = ON_BOARD, | |
| },{ /* 1 */ | |
| .name = "ATI SB600 SATA Legacy IDE", | |
| .init_hwif = init_hwif_sb600_legacy, | |
| .channels = 2, | |
| .autodma = AUTODMA, | |
| .bootable = ON_BOARD, | |
| } | |
| }; | |
| /** | |
| * atiixp_init_one - called when a ATIIXP is found | |
| * @dev: the atiixp device | |
| * @id: the matching pci id | |
| * | |
| * Called when the PCI registration layer (or the IDE initialization) | |
| * finds a device matching our IDE device tables. | |
| */ | |
| static int __devinit atiixp_init_one(struct pci_dev *dev, const struct pci_device_id *id) | |
| { | |
| return ide_setup_pci_device(dev, &atiixp_pci_info[id->driver_data]); | |
| } | |
| static struct pci_device_id atiixp_pci_tbl[] = { | |
| { PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP200_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, | |
| { PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP300_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, | |
| { PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP400_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, | |
| { PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, | |
| { PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_IXP600_SATA, PCI_ANY_ID, PCI_ANY_ID, (PCI_CLASS_STORAGE_IDE<<8)|0x8a, 0xffff05, 1}, | |
| { 0, }, | |
| }; | |
| MODULE_DEVICE_TABLE(pci, atiixp_pci_tbl); | |
| static struct pci_driver driver = { | |
| .name = "ATIIXP_IDE", | |
| .id_table = atiixp_pci_tbl, | |
| .probe = atiixp_init_one, | |
| }; | |
| static int atiixp_ide_init(void) | |
| { | |
| return ide_pci_register_driver(&driver); | |
| } | |
| module_init(atiixp_ide_init); | |
| MODULE_AUTHOR("HUI YU"); | |
| MODULE_DESCRIPTION("PCI driver module for ATI IXP IDE"); | |
| MODULE_LICENSE("GPL"); |