| /* | |
| * linux/drivers/ide/pci/cy82c693.c Version 0.40 Sep. 10, 2002 | |
| * | |
| * Copyright (C) 1998-2000 Andreas S. Krebs (akrebs@altavista.net), Maintainer | |
| * Copyright (C) 1998-2002 Andre Hedrick <andre@linux-ide.org>, Integrator | |
| * | |
| * CYPRESS CY82C693 chipset IDE controller | |
| * | |
| * The CY82C693 chipset is used on Digital's PC-Alpha 164SX boards. | |
| * Writing the driver was quite simple, since most of the job is | |
| * done by the generic pci-ide support. | |
| * The hard part was finding the CY82C693's datasheet on Cypress's | |
| * web page :-(. But Altavista solved this problem :-). | |
| * | |
| * | |
| * Notes: | |
| * - I recently got a 16.8G IBM DTTA, so I was able to test it with | |
| * a large and fast disk - the results look great, so I'd say the | |
| * driver is working fine :-) | |
| * hdparm -t reports 8.17 MB/sec at about 6% CPU usage for the DTTA | |
| * - this is my first linux driver, so there's probably a lot of room | |
| * for optimizations and bug fixing, so feel free to do it. | |
| * - use idebus=xx parameter to set PCI bus speed - needed to calc | |
| * timings for PIO modes (default will be 40) | |
| * - if using PIO mode it's a good idea to set the PIO mode and | |
| * 32-bit I/O support (if possible), e.g. hdparm -p2 -c1 /dev/hda | |
| * - I had some problems with my IBM DHEA with PIO modes < 2 | |
| * (lost interrupts) ????? | |
| * - first tests with DMA look okay, they seem to work, but there is a | |
| * problem with sound - the BusMaster IDE TimeOut should fixed this | |
| * | |
| * Ancient History: | |
| * AMH@1999-08-24: v0.34 init_cy82c693_chip moved to pci_init_cy82c693 | |
| * ASK@1999-01-23: v0.33 made a few minor code clean ups | |
| * removed DMA clock speed setting by default | |
| * added boot message | |
| * ASK@1998-11-01: v0.32 added support to set BusMaster IDE TimeOut | |
| * added support to set DMA Controller Clock Speed | |
| * ASK@1998-10-31: v0.31 fixed problem with setting to high DMA modes | |
| * on some drives. | |
| * ASK@1998-10-29: v0.3 added support to set DMA modes | |
| * ASK@1998-10-28: v0.2 added support to set PIO modes | |
| * ASK@1998-10-27: v0.1 first version - chipset detection | |
| * | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/types.h> | |
| #include <linux/pci.h> | |
| #include <linux/delay.h> | |
| #include <linux/ide.h> | |
| #include <linux/init.h> | |
| #include <asm/io.h> | |
| /* the current version */ | |
| #define CY82_VERSION "CY82C693U driver v0.34 99-13-12 Andreas S. Krebs (akrebs@altavista.net)" | |
| /* | |
| * The following are used to debug the driver. | |
| */ | |
| #define CY82C693_DEBUG_LOGS 0 | |
| #define CY82C693_DEBUG_INFO 0 | |
| /* define CY82C693_SETDMA_CLOCK to set DMA Controller Clock Speed to ATCLK */ | |
| #undef CY82C693_SETDMA_CLOCK | |
| /* | |
| * NOTE: the value for busmaster timeout is tricky and I got it by | |
| * trial and error! By using a to low value will cause DMA timeouts | |
| * and drop IDE performance, and by using a to high value will cause | |
| * audio playback to scatter. | |
| * If you know a better value or how to calc it, please let me know. | |
| */ | |
| /* twice the value written in cy82c693ub datasheet */ | |
| #define BUSMASTER_TIMEOUT 0x50 | |
| /* | |
| * the value above was tested on my machine and it seems to work okay | |
| */ | |
| /* here are the offset definitions for the registers */ | |
| #define CY82_IDE_CMDREG 0x04 | |
| #define CY82_IDE_ADDRSETUP 0x48 | |
| #define CY82_IDE_MASTER_IOR 0x4C | |
| #define CY82_IDE_MASTER_IOW 0x4D | |
| #define CY82_IDE_SLAVE_IOR 0x4E | |
| #define CY82_IDE_SLAVE_IOW 0x4F | |
| #define CY82_IDE_MASTER_8BIT 0x50 | |
| #define CY82_IDE_SLAVE_8BIT 0x51 | |
| #define CY82_INDEX_PORT 0x22 | |
| #define CY82_DATA_PORT 0x23 | |
| #define CY82_INDEX_CTRLREG1 0x01 | |
| #define CY82_INDEX_CHANNEL0 0x30 | |
| #define CY82_INDEX_CHANNEL1 0x31 | |
| #define CY82_INDEX_TIMEOUT 0x32 | |
| /* the max PIO mode - from datasheet */ | |
| #define CY82C693_MAX_PIO 4 | |
| /* the min and max PCI bus speed in MHz - from datasheet */ | |
| #define CY82C963_MIN_BUS_SPEED 25 | |
| #define CY82C963_MAX_BUS_SPEED 33 | |
| /* the struct for the PIO mode timings */ | |
| typedef struct pio_clocks_s { | |
| u8 address_time; /* Address setup (clocks) */ | |
| u8 time_16r; /* clocks for 16bit IOR (0xF0=Active/data, 0x0F=Recovery) */ | |
| u8 time_16w; /* clocks for 16bit IOW (0xF0=Active/data, 0x0F=Recovery) */ | |
| u8 time_8; /* clocks for 8bit (0xF0=Active/data, 0x0F=Recovery) */ | |
| } pio_clocks_t; | |
| /* | |
| * calc clocks using bus_speed | |
| * returns (rounded up) time in bus clocks for time in ns | |
| */ | |
| static int calc_clk (int time, int bus_speed) | |
| { | |
| int clocks; | |
| clocks = (time*bus_speed+999)/1000 -1; | |
| if (clocks < 0) | |
| clocks = 0; | |
| if (clocks > 0x0F) | |
| clocks = 0x0F; | |
| return clocks; | |
| } | |
| /* | |
| * compute the values for the clock registers for PIO | |
| * mode and pci_clk [MHz] speed | |
| * | |
| * NOTE: for mode 0,1 and 2 drives 8-bit IDE command control registers are used | |
| * for mode 3 and 4 drives 8 and 16-bit timings are the same | |
| * | |
| */ | |
| static void compute_clocks (u8 pio, pio_clocks_t *p_pclk) | |
| { | |
| int clk1, clk2; | |
| int bus_speed = system_bus_clock(); /* get speed of PCI bus */ | |
| /* we don't check against CY82C693's min and max speed, | |
| * so you can play with the idebus=xx parameter | |
| */ | |
| if (pio > CY82C693_MAX_PIO) | |
| pio = CY82C693_MAX_PIO; | |
| /* let's calc the address setup time clocks */ | |
| p_pclk->address_time = (u8)calc_clk(ide_pio_timings[pio].setup_time, bus_speed); | |
| /* let's calc the active and recovery time clocks */ | |
| clk1 = calc_clk(ide_pio_timings[pio].active_time, bus_speed); | |
| /* calc recovery timing */ | |
| clk2 = ide_pio_timings[pio].cycle_time - | |
| ide_pio_timings[pio].active_time - | |
| ide_pio_timings[pio].setup_time; | |
| clk2 = calc_clk(clk2, bus_speed); | |
| clk1 = (clk1<<4)|clk2; /* combine active and recovery clocks */ | |
| /* note: we use the same values for 16bit IOR and IOW | |
| * those are all the same, since I don't have other | |
| * timings than those from ide-lib.c | |
| */ | |
| p_pclk->time_16r = (u8)clk1; | |
| p_pclk->time_16w = (u8)clk1; | |
| /* what are good values for 8bit ?? */ | |
| p_pclk->time_8 = (u8)clk1; | |
| } | |
| /* | |
| * set DMA mode a specific channel for CY82C693 | |
| */ | |
| static void cy82c693_dma_enable (ide_drive_t *drive, int mode, int single) | |
| { | |
| u8 index = 0, data = 0; | |
| if (mode>2) /* make sure we set a valid mode */ | |
| mode = 2; | |
| if (mode > drive->id->tDMA) /* to be absolutly sure we have a valid mode */ | |
| mode = drive->id->tDMA; | |
| index = (HWIF(drive)->channel==0) ? CY82_INDEX_CHANNEL0 : CY82_INDEX_CHANNEL1; | |
| #if CY82C693_DEBUG_LOGS | |
| /* for debug let's show the previous values */ | |
| HWIF(drive)->OUTB(index, CY82_INDEX_PORT); | |
| data = HWIF(drive)->INB(CY82_DATA_PORT); | |
| printk (KERN_INFO "%s (ch=%d, dev=%d): DMA mode is %d (single=%d)\n", | |
| drive->name, HWIF(drive)->channel, drive->select.b.unit, | |
| (data&0x3), ((data>>2)&1)); | |
| #endif /* CY82C693_DEBUG_LOGS */ | |
| data = (u8)mode|(u8)(single<<2); | |
| HWIF(drive)->OUTB(index, CY82_INDEX_PORT); | |
| HWIF(drive)->OUTB(data, CY82_DATA_PORT); | |
| #if CY82C693_DEBUG_INFO | |
| printk(KERN_INFO "%s (ch=%d, dev=%d): set DMA mode to %d (single=%d)\n", | |
| drive->name, HWIF(drive)->channel, drive->select.b.unit, | |
| mode, single); | |
| #endif /* CY82C693_DEBUG_INFO */ | |
| /* | |
| * note: below we set the value for Bus Master IDE TimeOut Register | |
| * I'm not absolutly sure what this does, but it solved my problem | |
| * with IDE DMA and sound, so I now can play sound and work with | |
| * my IDE driver at the same time :-) | |
| * | |
| * If you know the correct (best) value for this register please | |
| * let me know - ASK | |
| */ | |
| data = BUSMASTER_TIMEOUT; | |
| HWIF(drive)->OUTB(CY82_INDEX_TIMEOUT, CY82_INDEX_PORT); | |
| HWIF(drive)->OUTB(data, CY82_DATA_PORT); | |
| #if CY82C693_DEBUG_INFO | |
| printk (KERN_INFO "%s: Set IDE Bus Master TimeOut Register to 0x%X\n", | |
| drive->name, data); | |
| #endif /* CY82C693_DEBUG_INFO */ | |
| } | |
| /* | |
| * used to set DMA mode for CY82C693 (single and multi modes) | |
| */ | |
| static int cy82c693_ide_dma_on (ide_drive_t *drive) | |
| { | |
| struct hd_driveid *id = drive->id; | |
| #if CY82C693_DEBUG_INFO | |
| printk (KERN_INFO "dma_on: %s\n", drive->name); | |
| #endif /* CY82C693_DEBUG_INFO */ | |
| if (id != NULL) { | |
| /* Enable DMA on any drive that has DMA | |
| * (multi or single) enabled | |
| */ | |
| if (id->field_valid & 2) { /* regular DMA */ | |
| int mmode, smode; | |
| mmode = id->dma_mword & (id->dma_mword >> 8); | |
| smode = id->dma_1word & (id->dma_1word >> 8); | |
| if (mmode != 0) { | |
| /* enable multi */ | |
| cy82c693_dma_enable(drive, (mmode >> 1), 0); | |
| } else if (smode != 0) { | |
| /* enable single */ | |
| cy82c693_dma_enable(drive, (smode >> 1), 1); | |
| } | |
| } | |
| } | |
| return __ide_dma_on(drive); | |
| } | |
| /* | |
| * tune ide drive - set PIO mode | |
| */ | |
| static void cy82c693_tune_drive (ide_drive_t *drive, u8 pio) | |
| { | |
| ide_hwif_t *hwif = HWIF(drive); | |
| struct pci_dev *dev = hwif->pci_dev; | |
| pio_clocks_t pclk; | |
| unsigned int addrCtrl; | |
| /* select primary or secondary channel */ | |
| if (hwif->index > 0) { /* drive is on the secondary channel */ | |
| dev = pci_get_slot(dev->bus, dev->devfn+1); | |
| if (!dev) { | |
| printk(KERN_ERR "%s: tune_drive: " | |
| "Cannot find secondary interface!\n", | |
| drive->name); | |
| return; | |
| } | |
| } | |
| #if CY82C693_DEBUG_LOGS | |
| /* for debug let's show the register values */ | |
| if (drive->select.b.unit == 0) { | |
| /* | |
| * get master drive registers | |
| * address setup control register | |
| * is 32 bit !!! | |
| */ | |
| pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl); | |
| addrCtrl &= 0x0F; | |
| /* now let's get the remaining registers */ | |
| pci_read_config_byte(dev, CY82_IDE_MASTER_IOR, &pclk.time_16r); | |
| pci_read_config_byte(dev, CY82_IDE_MASTER_IOW, &pclk.time_16w); | |
| pci_read_config_byte(dev, CY82_IDE_MASTER_8BIT, &pclk.time_8); | |
| } else { | |
| /* | |
| * set slave drive registers | |
| * address setup control register | |
| * is 32 bit !!! | |
| */ | |
| pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl); | |
| addrCtrl &= 0xF0; | |
| addrCtrl >>= 4; | |
| /* now let's get the remaining registers */ | |
| pci_read_config_byte(dev, CY82_IDE_SLAVE_IOR, &pclk.time_16r); | |
| pci_read_config_byte(dev, CY82_IDE_SLAVE_IOW, &pclk.time_16w); | |
| pci_read_config_byte(dev, CY82_IDE_SLAVE_8BIT, &pclk.time_8); | |
| } | |
| printk(KERN_INFO "%s (ch=%d, dev=%d): PIO timing is " | |
| "(addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n", | |
| drive->name, hwif->channel, drive->select.b.unit, | |
| addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8); | |
| #endif /* CY82C693_DEBUG_LOGS */ | |
| /* first let's calc the pio modes */ | |
| pio = ide_get_best_pio_mode(drive, pio, CY82C693_MAX_PIO, NULL); | |
| #if CY82C693_DEBUG_INFO | |
| printk (KERN_INFO "%s: Selected PIO mode %d\n", drive->name, pio); | |
| #endif /* CY82C693_DEBUG_INFO */ | |
| /* let's calc the values for this PIO mode */ | |
| compute_clocks(pio, &pclk); | |
| /* now let's write the clocks registers */ | |
| if (drive->select.b.unit == 0) { | |
| /* | |
| * set master drive | |
| * address setup control register | |
| * is 32 bit !!! | |
| */ | |
| pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl); | |
| addrCtrl &= (~0xF); | |
| addrCtrl |= (unsigned int)pclk.address_time; | |
| pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl); | |
| /* now let's set the remaining registers */ | |
| pci_write_config_byte(dev, CY82_IDE_MASTER_IOR, pclk.time_16r); | |
| pci_write_config_byte(dev, CY82_IDE_MASTER_IOW, pclk.time_16w); | |
| pci_write_config_byte(dev, CY82_IDE_MASTER_8BIT, pclk.time_8); | |
| addrCtrl &= 0xF; | |
| } else { | |
| /* | |
| * set slave drive | |
| * address setup control register | |
| * is 32 bit !!! | |
| */ | |
| pci_read_config_dword(dev, CY82_IDE_ADDRSETUP, &addrCtrl); | |
| addrCtrl &= (~0xF0); | |
| addrCtrl |= ((unsigned int)pclk.address_time<<4); | |
| pci_write_config_dword(dev, CY82_IDE_ADDRSETUP, addrCtrl); | |
| /* now let's set the remaining registers */ | |
| pci_write_config_byte(dev, CY82_IDE_SLAVE_IOR, pclk.time_16r); | |
| pci_write_config_byte(dev, CY82_IDE_SLAVE_IOW, pclk.time_16w); | |
| pci_write_config_byte(dev, CY82_IDE_SLAVE_8BIT, pclk.time_8); | |
| addrCtrl >>= 4; | |
| addrCtrl &= 0xF; | |
| } | |
| #if CY82C693_DEBUG_INFO | |
| printk(KERN_INFO "%s (ch=%d, dev=%d): set PIO timing to " | |
| "(addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n", | |
| drive->name, hwif->channel, drive->select.b.unit, | |
| addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8); | |
| #endif /* CY82C693_DEBUG_INFO */ | |
| } | |
| /* | |
| * this function is called during init and is used to setup the cy82c693 chip | |
| */ | |
| static unsigned int __devinit init_chipset_cy82c693(struct pci_dev *dev, const char *name) | |
| { | |
| if (PCI_FUNC(dev->devfn) != 1) | |
| return 0; | |
| #ifdef CY82C693_SETDMA_CLOCK | |
| u8 data = 0; | |
| #endif /* CY82C693_SETDMA_CLOCK */ | |
| /* write info about this verion of the driver */ | |
| printk(KERN_INFO CY82_VERSION "\n"); | |
| #ifdef CY82C693_SETDMA_CLOCK | |
| /* okay let's set the DMA clock speed */ | |
| outb(CY82_INDEX_CTRLREG1, CY82_INDEX_PORT); | |
| data = inb(CY82_DATA_PORT); | |
| #if CY82C693_DEBUG_INFO | |
| printk(KERN_INFO "%s: Peripheral Configuration Register: 0x%X\n", | |
| name, data); | |
| #endif /* CY82C693_DEBUG_INFO */ | |
| /* | |
| * for some reason sometimes the DMA controller | |
| * speed is set to ATCLK/2 ???? - we fix this here | |
| * | |
| * note: i don't know what causes this strange behaviour, | |
| * but even changing the dma speed doesn't solve it :-( | |
| * the ide performance is still only half the normal speed | |
| * | |
| * if anybody knows what goes wrong with my machine, please | |
| * let me know - ASK | |
| */ | |
| data |= 0x03; | |
| outb(CY82_INDEX_CTRLREG1, CY82_INDEX_PORT); | |
| outb(data, CY82_DATA_PORT); | |
| #if CY82C693_DEBUG_INFO | |
| printk (KERN_INFO "%s: New Peripheral Configuration Register: 0x%X\n", | |
| name, data); | |
| #endif /* CY82C693_DEBUG_INFO */ | |
| #endif /* CY82C693_SETDMA_CLOCK */ | |
| return 0; | |
| } | |
| /* | |
| * the init function - called for each ide channel once | |
| */ | |
| static void __devinit init_hwif_cy82c693(ide_hwif_t *hwif) | |
| { | |
| hwif->autodma = 0; | |
| hwif->chipset = ide_cy82c693; | |
| hwif->tuneproc = &cy82c693_tune_drive; | |
| if (!hwif->dma_base) { | |
| hwif->drives[0].autotune = 1; | |
| hwif->drives[1].autotune = 1; | |
| return; | |
| } | |
| hwif->atapi_dma = 1; | |
| hwif->mwdma_mask = 0x04; | |
| hwif->swdma_mask = 0x04; | |
| hwif->ide_dma_on = &cy82c693_ide_dma_on; | |
| if (!noautodma) | |
| hwif->autodma = 1; | |
| hwif->drives[0].autodma = hwif->autodma; | |
| hwif->drives[1].autodma = hwif->autodma; | |
| } | |
| static __devinitdata ide_hwif_t *primary; | |
| static void __devinit init_iops_cy82c693(ide_hwif_t *hwif) | |
| { | |
| if (PCI_FUNC(hwif->pci_dev->devfn) == 1) | |
| primary = hwif; | |
| else { | |
| hwif->mate = primary; | |
| hwif->channel = 1; | |
| } | |
| } | |
| static ide_pci_device_t cy82c693_chipsets[] __devinitdata = { | |
| { /* 0 */ | |
| .name = "CY82C693", | |
| .init_chipset = init_chipset_cy82c693, | |
| .init_iops = init_iops_cy82c693, | |
| .init_hwif = init_hwif_cy82c693, | |
| .channels = 1, | |
| .autodma = AUTODMA, | |
| .bootable = ON_BOARD, | |
| } | |
| }; | |
| static int __devinit cy82c693_init_one(struct pci_dev *dev, const struct pci_device_id *id) | |
| { | |
| ide_pci_device_t *d = &cy82c693_chipsets[id->driver_data]; | |
| struct pci_dev *dev2; | |
| int ret = -ENODEV; | |
| /* CY82C693 is more than only a IDE controller. | |
| Function 1 is primary IDE channel, function 2 - secondary. */ | |
| if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE && | |
| PCI_FUNC(dev->devfn) == 1) { | |
| dev2 = pci_get_slot(dev->bus, dev->devfn + 1); | |
| ret = ide_setup_pci_devices(dev, dev2, d); | |
| /* We leak pci refs here but thats ok - we can't be unloaded */ | |
| } | |
| return ret; | |
| } | |
| static struct pci_device_id cy82c693_pci_tbl[] = { | |
| { PCI_VENDOR_ID_CONTAQ, PCI_DEVICE_ID_CONTAQ_82C693, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, | |
| { 0, }, | |
| }; | |
| MODULE_DEVICE_TABLE(pci, cy82c693_pci_tbl); | |
| static struct pci_driver driver = { | |
| .name = "Cypress_IDE", | |
| .id_table = cy82c693_pci_tbl, | |
| .probe = cy82c693_init_one, | |
| }; | |
| static int cy82c693_ide_init(void) | |
| { | |
| return ide_pci_register_driver(&driver); | |
| } | |
| module_init(cy82c693_ide_init); | |
| MODULE_AUTHOR("Andreas Krebs, Andre Hedrick"); | |
| MODULE_DESCRIPTION("PCI driver module for the Cypress CY82C693 IDE"); | |
| MODULE_LICENSE("GPL"); |