| #include <media/saa7146_vv.h> | |
| static u32 saa7146_i2c_func(struct i2c_adapter *adapter) | |
| { | |
| //fm DEB_I2C(("'%s'.\n", adapter->name)); | |
| return I2C_FUNC_I2C | |
| | I2C_FUNC_SMBUS_QUICK | |
| | I2C_FUNC_SMBUS_READ_BYTE | I2C_FUNC_SMBUS_WRITE_BYTE | |
| | I2C_FUNC_SMBUS_READ_BYTE_DATA | I2C_FUNC_SMBUS_WRITE_BYTE_DATA; | |
| } | |
| /* this function returns the status-register of our i2c-device */ | |
| static inline u32 saa7146_i2c_status(struct saa7146_dev *dev) | |
| { | |
| u32 iicsta = saa7146_read(dev, I2C_STATUS); | |
| /* | |
| DEB_I2C(("status: 0x%08x\n",iicsta)); | |
| */ | |
| return iicsta; | |
| } | |
| /* this function runs through the i2c-messages and prepares the data to be | |
| sent through the saa7146. have a look at the specifications p. 122 ff | |
| to understand this. it returns the number of u32s to send, or -1 | |
| in case of an error. */ | |
| static int saa7146_i2c_msg_prepare(const struct i2c_msg *m, int num, u32 *op) | |
| { | |
| int h1, h2; | |
| int i, j, addr; | |
| int mem = 0, op_count = 0; | |
| /* first determine size of needed memory */ | |
| for(i = 0; i < num; i++) { | |
| mem += m[i].len + 1; | |
| } | |
| /* worst case: we need one u32 for three bytes to be send | |
| plus one extra byte to address the device */ | |
| mem = 1 + ((mem-1) / 3); | |
| /* we assume that op points to a memory of at least SAA7146_I2C_MEM bytes | |
| size. if we exceed this limit... */ | |
| if ( (4*mem) > SAA7146_I2C_MEM ) { | |
| //fm DEB_I2C(("cannot prepare i2c-message.\n")); | |
| return -ENOMEM; | |
| } | |
| /* be careful: clear out the i2c-mem first */ | |
| memset(op,0,sizeof(u32)*mem); | |
| /* loop through all messages */ | |
| for(i = 0; i < num; i++) { | |
| /* insert the address of the i2c-slave. | |
| note: we get 7 bit i2c-addresses, | |
| so we have to perform a translation */ | |
| addr = (m[i].addr*2) + ( (0 != (m[i].flags & I2C_M_RD)) ? 1 : 0); | |
| h1 = op_count/3; h2 = op_count%3; | |
| op[h1] |= ( (u8)addr << ((3-h2)*8)); | |
| op[h1] |= (SAA7146_I2C_START << ((3-h2)*2)); | |
| op_count++; | |
| /* loop through all bytes of message i */ | |
| for(j = 0; j < m[i].len; j++) { | |
| /* insert the data bytes */ | |
| h1 = op_count/3; h2 = op_count%3; | |
| op[h1] |= ( (u32)((u8)m[i].buf[j]) << ((3-h2)*8)); | |
| op[h1] |= ( SAA7146_I2C_CONT << ((3-h2)*2)); | |
| op_count++; | |
| } | |
| } | |
| /* have a look at the last byte inserted: | |
| if it was: ...CONT change it to ...STOP */ | |
| h1 = (op_count-1)/3; h2 = (op_count-1)%3; | |
| if ( SAA7146_I2C_CONT == (0x3 & (op[h1] >> ((3-h2)*2))) ) { | |
| op[h1] &= ~(0x2 << ((3-h2)*2)); | |
| op[h1] |= (SAA7146_I2C_STOP << ((3-h2)*2)); | |
| } | |
| /* return the number of u32s to send */ | |
| return mem; | |
| } | |
| /* this functions loops through all i2c-messages. normally, it should determine | |
| which bytes were read through the adapter and write them back to the corresponding | |
| i2c-message. but instead, we simply write back all bytes. | |
| fixme: this could be improved. */ | |
| static int saa7146_i2c_msg_cleanup(const struct i2c_msg *m, int num, u32 *op) | |
| { | |
| int i, j; | |
| int op_count = 0; | |
| /* loop through all messages */ | |
| for(i = 0; i < num; i++) { | |
| op_count++; | |
| /* loop throgh all bytes of message i */ | |
| for(j = 0; j < m[i].len; j++) { | |
| /* write back all bytes that could have been read */ | |
| m[i].buf[j] = (op[op_count/3] >> ((3-(op_count%3))*8)); | |
| op_count++; | |
| } | |
| } | |
| return 0; | |
| } | |
| /* this functions resets the i2c-device and returns 0 if everything was fine, otherwise -1 */ | |
| static int saa7146_i2c_reset(struct saa7146_dev *dev) | |
| { | |
| /* get current status */ | |
| u32 status = saa7146_i2c_status(dev); | |
| /* clear registers for sure */ | |
| saa7146_write(dev, I2C_STATUS, dev->i2c_bitrate); | |
| saa7146_write(dev, I2C_TRANSFER, 0); | |
| /* check if any operation is still in progress */ | |
| if ( 0 != ( status & SAA7146_I2C_BUSY) ) { | |
| /* yes, kill ongoing operation */ | |
| DEB_I2C(("busy_state detected.\n")); | |
| /* set "ABORT-OPERATION"-bit (bit 7)*/ | |
| saa7146_write(dev, I2C_STATUS, (dev->i2c_bitrate | MASK_07)); | |
| saa7146_write(dev, MC2, (MASK_00 | MASK_16)); | |
| msleep(SAA7146_I2C_DELAY); | |
| /* clear all error-bits pending; this is needed because p.123, note 1 */ | |
| saa7146_write(dev, I2C_STATUS, dev->i2c_bitrate); | |
| saa7146_write(dev, MC2, (MASK_00 | MASK_16)); | |
| msleep(SAA7146_I2C_DELAY); | |
| } | |
| /* check if any error is (still) present. (this can be necessary because p.123, note 1) */ | |
| status = saa7146_i2c_status(dev); | |
| if ( dev->i2c_bitrate != status ) { | |
| DEB_I2C(("error_state detected. status:0x%08x\n",status)); | |
| /* Repeat the abort operation. This seems to be necessary | |
| after serious protocol errors caused by e.g. the SAA7740 */ | |
| saa7146_write(dev, I2C_STATUS, (dev->i2c_bitrate | MASK_07)); | |
| saa7146_write(dev, MC2, (MASK_00 | MASK_16)); | |
| msleep(SAA7146_I2C_DELAY); | |
| /* clear all error-bits pending */ | |
| saa7146_write(dev, I2C_STATUS, dev->i2c_bitrate); | |
| saa7146_write(dev, MC2, (MASK_00 | MASK_16)); | |
| msleep(SAA7146_I2C_DELAY); | |
| /* the data sheet says it might be necessary to clear the status | |
| twice after an abort */ | |
| saa7146_write(dev, I2C_STATUS, dev->i2c_bitrate); | |
| saa7146_write(dev, MC2, (MASK_00 | MASK_16)); | |
| msleep(SAA7146_I2C_DELAY); | |
| } | |
| /* if any error is still present, a fatal error has occured ... */ | |
| status = saa7146_i2c_status(dev); | |
| if ( dev->i2c_bitrate != status ) { | |
| DEB_I2C(("fatal error. status:0x%08x\n",status)); | |
| return -1; | |
| } | |
| return 0; | |
| } | |
| /* this functions writes out the data-byte 'dword' to the i2c-device. | |
| it returns 0 if ok, -1 if the transfer failed, -2 if the transfer | |
| failed badly (e.g. address error) */ | |
| static int saa7146_i2c_writeout(struct saa7146_dev *dev, u32* dword, int short_delay) | |
| { | |
| u32 status = 0, mc2 = 0; | |
| int trial = 0; | |
| unsigned long timeout; | |
| /* write out i2c-command */ | |
| DEB_I2C(("before: 0x%08x (status: 0x%08x), %d\n",*dword,saa7146_read(dev, I2C_STATUS), dev->i2c_op)); | |
| if( 0 != (SAA7146_USE_I2C_IRQ & dev->ext->flags)) { | |
| saa7146_write(dev, I2C_STATUS, dev->i2c_bitrate); | |
| saa7146_write(dev, I2C_TRANSFER, *dword); | |
| dev->i2c_op = 1; | |
| SAA7146_IER_ENABLE(dev, MASK_16|MASK_17); | |
| saa7146_write(dev, MC2, (MASK_00 | MASK_16)); | |
| wait_event_interruptible(dev->i2c_wq, dev->i2c_op == 0); | |
| if (signal_pending (current)) { | |
| /* a signal arrived */ | |
| return -ERESTARTSYS; | |
| } | |
| status = saa7146_read(dev, I2C_STATUS); | |
| } else { | |
| saa7146_write(dev, I2C_STATUS, dev->i2c_bitrate); | |
| saa7146_write(dev, I2C_TRANSFER, *dword); | |
| saa7146_write(dev, MC2, (MASK_00 | MASK_16)); | |
| /* do not poll for i2c-status before upload is complete */ | |
| timeout = jiffies + HZ/100 + 1; /* 10ms */ | |
| while(1) { | |
| mc2 = (saa7146_read(dev, MC2) & 0x1); | |
| if( 0 != mc2 ) { | |
| break; | |
| } | |
| if (time_after(jiffies,timeout)) { | |
| printk(KERN_WARNING "saa7146_i2c_writeout: timed out waiting for MC2\n"); | |
| return -EIO; | |
| } | |
| } | |
| /* wait until we get a transfer done or error */ | |
| timeout = jiffies + HZ/100 + 1; /* 10ms */ | |
| /* first read usually delivers bogus results... */ | |
| saa7146_i2c_status(dev); | |
| while(1) { | |
| status = saa7146_i2c_status(dev); | |
| if ((status & 0x3) != 1) | |
| break; | |
| if (time_after(jiffies,timeout)) { | |
| /* this is normal when probing the bus | |
| * (no answer from nonexisistant device...) | |
| */ | |
| DEB_I2C(("saa7146_i2c_writeout: timed out waiting for end of xfer\n")); | |
| return -EIO; | |
| } | |
| if (++trial < 50 && short_delay) | |
| udelay(10); | |
| else | |
| msleep(1); | |
| } | |
| } | |
| /* give a detailed status report */ | |
| if ( 0 != (status & SAA7146_I2C_ERR)) { | |
| if( 0 != (status & SAA7146_I2C_SPERR) ) { | |
| DEB_I2C(("error due to invalid start/stop condition.\n")); | |
| } | |
| if( 0 != (status & SAA7146_I2C_DTERR) ) { | |
| DEB_I2C(("error in data transmission.\n")); | |
| } | |
| if( 0 != (status & SAA7146_I2C_DRERR) ) { | |
| DEB_I2C(("error when receiving data.\n")); | |
| } | |
| if( 0 != (status & SAA7146_I2C_AL) ) { | |
| DEB_I2C(("error because arbitration lost.\n")); | |
| } | |
| /* we handle address-errors here */ | |
| if( 0 != (status & SAA7146_I2C_APERR) ) { | |
| DEB_I2C(("error in address phase.\n")); | |
| return -EREMOTEIO; | |
| } | |
| return -EIO; | |
| } | |
| /* read back data, just in case we were reading ... */ | |
| *dword = saa7146_read(dev, I2C_TRANSFER); | |
| DEB_I2C(("after: 0x%08x\n",*dword)); | |
| return 0; | |
| } | |
| int saa7146_i2c_transfer(struct saa7146_dev *dev, const struct i2c_msg *msgs, int num, int retries) | |
| { | |
| int i = 0, count = 0; | |
| u32* buffer = dev->d_i2c.cpu_addr; | |
| int err = 0; | |
| int address_err = 0; | |
| int short_delay = 0; | |
| if (mutex_lock_interruptible(&dev->i2c_lock)) | |
| return -ERESTARTSYS; | |
| for(i=0;i<num;i++) { | |
| DEB_I2C(("msg:%d/%d\n",i+1,num)); | |
| } | |
| /* prepare the message(s), get number of u32s to transfer */ | |
| count = saa7146_i2c_msg_prepare(msgs, num, buffer); | |
| if ( 0 > count ) { | |
| err = -1; | |
| goto out; | |
| } | |
| if ( count > 3 || 0 != (SAA7146_I2C_SHORT_DELAY & dev->ext->flags) ) | |
| short_delay = 1; | |
| do { | |
| /* reset the i2c-device if necessary */ | |
| err = saa7146_i2c_reset(dev); | |
| if ( 0 > err ) { | |
| DEB_I2C(("could not reset i2c-device.\n")); | |
| goto out; | |
| } | |
| /* write out the u32s one after another */ | |
| for(i = 0; i < count; i++) { | |
| err = saa7146_i2c_writeout(dev, &buffer[i], short_delay); | |
| if ( 0 != err) { | |
| /* this one is unsatisfying: some i2c slaves on some | |
| dvb cards don't acknowledge correctly, so the saa7146 | |
| thinks that an address error occured. in that case, the | |
| transaction should be retrying, even if an address error | |
| occured. analog saa7146 based cards extensively rely on | |
| i2c address probing, however, and address errors indicate that a | |
| device is really *not* there. retrying in that case | |
| increases the time the device needs to probe greatly, so | |
| it should be avoided. because of the fact, that only | |
| analog based cards use irq based i2c transactions (for dvb | |
| cards, this screwes up other interrupt sources), we bail out | |
| completely for analog cards after an address error and trust | |
| the saa7146 address error detection. */ | |
| if ( -EREMOTEIO == err ) { | |
| if( 0 != (SAA7146_USE_I2C_IRQ & dev->ext->flags)) { | |
| goto out; | |
| } | |
| address_err++; | |
| } | |
| DEB_I2C(("error while sending message(s). starting again.\n")); | |
| break; | |
| } | |
| } | |
| if( 0 == err ) { | |
| err = num; | |
| break; | |
| } | |
| /* delay a bit before retrying */ | |
| msleep(10); | |
| } while (err != num && retries--); | |
| /* if every retry had an address error, exit right away */ | |
| if (address_err == retries) { | |
| goto out; | |
| } | |
| /* if any things had to be read, get the results */ | |
| if ( 0 != saa7146_i2c_msg_cleanup(msgs, num, buffer)) { | |
| DEB_I2C(("could not cleanup i2c-message.\n")); | |
| err = -1; | |
| goto out; | |
| } | |
| /* return the number of delivered messages */ | |
| DEB_I2C(("transmission successful. (msg:%d).\n",err)); | |
| out: | |
| /* another bug in revision 0: the i2c-registers get uploaded randomly by other | |
| uploads, so we better clear them out before continueing */ | |
| if( 0 == dev->revision ) { | |
| u32 zero = 0; | |
| saa7146_i2c_reset(dev); | |
| if( 0 != saa7146_i2c_writeout(dev, &zero, short_delay)) { | |
| INFO(("revision 0 error. this should never happen.\n")); | |
| } | |
| } | |
| mutex_unlock(&dev->i2c_lock); | |
| return err; | |
| } | |
| /* utility functions */ | |
| static int saa7146_i2c_xfer(struct i2c_adapter* adapter, struct i2c_msg *msg, int num) | |
| { | |
| struct saa7146_dev* dev = i2c_get_adapdata(adapter); | |
| /* use helper function to transfer data */ | |
| return saa7146_i2c_transfer(dev, msg, num, adapter->retries); | |
| } | |
| /*****************************************************************************/ | |
| /* i2c-adapter helper functions */ | |
| #include <linux/i2c-id.h> | |
| /* exported algorithm data */ | |
| static struct i2c_algorithm saa7146_algo = { | |
| .master_xfer = saa7146_i2c_xfer, | |
| .functionality = saa7146_i2c_func, | |
| }; | |
| int saa7146_i2c_adapter_prepare(struct saa7146_dev *dev, struct i2c_adapter *i2c_adapter, u32 bitrate) | |
| { | |
| DEB_EE(("bitrate: 0x%08x\n",bitrate)); | |
| /* enable i2c-port pins */ | |
| saa7146_write(dev, MC1, (MASK_08 | MASK_24)); | |
| dev->i2c_bitrate = bitrate; | |
| saa7146_i2c_reset(dev); | |
| if( NULL != i2c_adapter ) { | |
| BUG_ON(!i2c_adapter->class); | |
| i2c_set_adapdata(i2c_adapter,dev); | |
| i2c_adapter->dev.parent = &dev->pci->dev; | |
| i2c_adapter->algo = &saa7146_algo; | |
| i2c_adapter->algo_data = NULL; | |
| i2c_adapter->id = I2C_HW_SAA7146; | |
| i2c_adapter->timeout = SAA7146_I2C_TIMEOUT; | |
| i2c_adapter->retries = SAA7146_I2C_RETRIES; | |
| } | |
| return 0; | |
| } |