| /* | |
| * linux/drivers/mmc/at91_mci.c - ATMEL AT91RM9200 MCI Driver | |
| * | |
| * Copyright (C) 2005 Cougar Creek Computing Devices Ltd, All Rights Reserved | |
| * | |
| * Copyright (C) 2006 Malcolm Noyes | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License version 2 as | |
| * published by the Free Software Foundation. | |
| */ | |
| /* | |
| This is the AT91RM9200 MCI driver that has been tested with both MMC cards | |
| and SD-cards. Boards that support write protect are now supported. | |
| The CCAT91SBC001 board does not support SD cards. | |
| The three entry points are at91_mci_request, at91_mci_set_ios | |
| and at91_mci_get_ro. | |
| SET IOS | |
| This configures the device to put it into the correct mode and clock speed | |
| required. | |
| MCI REQUEST | |
| MCI request processes the commands sent in the mmc_request structure. This | |
| can consist of a processing command and a stop command in the case of | |
| multiple block transfers. | |
| There are three main types of request, commands, reads and writes. | |
| Commands are straight forward. The command is submitted to the controller and | |
| the request function returns. When the controller generates an interrupt to indicate | |
| the command is finished, the response to the command are read and the mmc_request_done | |
| function called to end the request. | |
| Reads and writes work in a similar manner to normal commands but involve the PDC (DMA) | |
| controller to manage the transfers. | |
| A read is done from the controller directly to the scatterlist passed in from the request. | |
| Due to a bug in the controller, when a read is completed, all the words are byte | |
| swapped in the scatterlist buffers. | |
| The sequence of read interrupts is: ENDRX, RXBUFF, CMDRDY | |
| A write is slightly different in that the bytes to write are read from the scatterlist | |
| into a dma memory buffer (this is in case the source buffer should be read only). The | |
| entire write buffer is then done from this single dma memory buffer. | |
| The sequence of write interrupts is: ENDTX, TXBUFE, NOTBUSY, CMDRDY | |
| GET RO | |
| Gets the status of the write protect pin, if available. | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/moduleparam.h> | |
| #include <linux/init.h> | |
| #include <linux/ioport.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/blkdev.h> | |
| #include <linux/delay.h> | |
| #include <linux/err.h> | |
| #include <linux/dma-mapping.h> | |
| #include <linux/clk.h> | |
| #include <linux/mmc/host.h> | |
| #include <linux/mmc/protocol.h> | |
| #include <asm/io.h> | |
| #include <asm/irq.h> | |
| #include <asm/mach/mmc.h> | |
| #include <asm/arch/board.h> | |
| #include <asm/arch/gpio.h> | |
| #include <asm/arch/at91rm9200_mci.h> | |
| #include <asm/arch/at91rm9200_pdc.h> | |
| #define DRIVER_NAME "at91_mci" | |
| #undef SUPPORT_4WIRE | |
| static struct clk *mci_clk; | |
| #define FL_SENT_COMMAND (1 << 0) | |
| #define FL_SENT_STOP (1 << 1) | |
| /* | |
| * Read from a MCI register. | |
| */ | |
| static inline unsigned long at91_mci_read(unsigned int reg) | |
| { | |
| void __iomem *mci_base = (void __iomem *)AT91_VA_BASE_MCI; | |
| return __raw_readl(mci_base + reg); | |
| } | |
| /* | |
| * Write to a MCI register. | |
| */ | |
| static inline void at91_mci_write(unsigned int reg, unsigned long value) | |
| { | |
| void __iomem *mci_base = (void __iomem *)AT91_VA_BASE_MCI; | |
| __raw_writel(value, mci_base + reg); | |
| } | |
| /* | |
| * Low level type for this driver | |
| */ | |
| struct at91mci_host | |
| { | |
| struct mmc_host *mmc; | |
| struct mmc_command *cmd; | |
| struct mmc_request *request; | |
| struct at91_mmc_data *board; | |
| int present; | |
| /* | |
| * Flag indicating when the command has been sent. This is used to | |
| * work out whether or not to send the stop | |
| */ | |
| unsigned int flags; | |
| /* flag for current bus settings */ | |
| u32 bus_mode; | |
| /* DMA buffer used for transmitting */ | |
| unsigned int* buffer; | |
| dma_addr_t physical_address; | |
| unsigned int total_length; | |
| /* Latest in the scatterlist that has been enabled for transfer, but not freed */ | |
| int in_use_index; | |
| /* Latest in the scatterlist that has been enabled for transfer */ | |
| int transfer_index; | |
| }; | |
| /* | |
| * Copy from sg to a dma block - used for transfers | |
| */ | |
| static inline void at91mci_sg_to_dma(struct at91mci_host *host, struct mmc_data *data) | |
| { | |
| unsigned int len, i, size; | |
| unsigned *dmabuf = host->buffer; | |
| size = host->total_length; | |
| len = data->sg_len; | |
| /* | |
| * Just loop through all entries. Size might not | |
| * be the entire list though so make sure that | |
| * we do not transfer too much. | |
| */ | |
| for (i = 0; i < len; i++) { | |
| struct scatterlist *sg; | |
| int amount; | |
| int index; | |
| unsigned int *sgbuffer; | |
| sg = &data->sg[i]; | |
| sgbuffer = kmap_atomic(sg->page, KM_BIO_SRC_IRQ) + sg->offset; | |
| amount = min(size, sg->length); | |
| size -= amount; | |
| amount /= 4; | |
| for (index = 0; index < amount; index++) | |
| *dmabuf++ = swab32(sgbuffer[index]); | |
| kunmap_atomic(sgbuffer, KM_BIO_SRC_IRQ); | |
| if (size == 0) | |
| break; | |
| } | |
| /* | |
| * Check that we didn't get a request to transfer | |
| * more data than can fit into the SG list. | |
| */ | |
| BUG_ON(size != 0); | |
| } | |
| /* | |
| * Prepare a dma read | |
| */ | |
| static void at91mci_pre_dma_read(struct at91mci_host *host) | |
| { | |
| int i; | |
| struct scatterlist *sg; | |
| struct mmc_command *cmd; | |
| struct mmc_data *data; | |
| pr_debug("pre dma read\n"); | |
| cmd = host->cmd; | |
| if (!cmd) { | |
| pr_debug("no command\n"); | |
| return; | |
| } | |
| data = cmd->data; | |
| if (!data) { | |
| pr_debug("no data\n"); | |
| return; | |
| } | |
| for (i = 0; i < 2; i++) { | |
| /* nothing left to transfer */ | |
| if (host->transfer_index >= data->sg_len) { | |
| pr_debug("Nothing left to transfer (index = %d)\n", host->transfer_index); | |
| break; | |
| } | |
| /* Check to see if this needs filling */ | |
| if (i == 0) { | |
| if (at91_mci_read(AT91_PDC_RCR) != 0) { | |
| pr_debug("Transfer active in current\n"); | |
| continue; | |
| } | |
| } | |
| else { | |
| if (at91_mci_read(AT91_PDC_RNCR) != 0) { | |
| pr_debug("Transfer active in next\n"); | |
| continue; | |
| } | |
| } | |
| /* Setup the next transfer */ | |
| pr_debug("Using transfer index %d\n", host->transfer_index); | |
| sg = &data->sg[host->transfer_index++]; | |
| pr_debug("sg = %p\n", sg); | |
| sg->dma_address = dma_map_page(NULL, sg->page, sg->offset, sg->length, DMA_FROM_DEVICE); | |
| pr_debug("dma address = %08X, length = %d\n", sg->dma_address, sg->length); | |
| if (i == 0) { | |
| at91_mci_write(AT91_PDC_RPR, sg->dma_address); | |
| at91_mci_write(AT91_PDC_RCR, sg->length / 4); | |
| } | |
| else { | |
| at91_mci_write(AT91_PDC_RNPR, sg->dma_address); | |
| at91_mci_write(AT91_PDC_RNCR, sg->length / 4); | |
| } | |
| } | |
| pr_debug("pre dma read done\n"); | |
| } | |
| /* | |
| * Handle after a dma read | |
| */ | |
| static void at91mci_post_dma_read(struct at91mci_host *host) | |
| { | |
| struct mmc_command *cmd; | |
| struct mmc_data *data; | |
| pr_debug("post dma read\n"); | |
| cmd = host->cmd; | |
| if (!cmd) { | |
| pr_debug("no command\n"); | |
| return; | |
| } | |
| data = cmd->data; | |
| if (!data) { | |
| pr_debug("no data\n"); | |
| return; | |
| } | |
| while (host->in_use_index < host->transfer_index) { | |
| unsigned int *buffer; | |
| int index; | |
| int len; | |
| struct scatterlist *sg; | |
| pr_debug("finishing index %d\n", host->in_use_index); | |
| sg = &data->sg[host->in_use_index++]; | |
| pr_debug("Unmapping page %08X\n", sg->dma_address); | |
| dma_unmap_page(NULL, sg->dma_address, sg->length, DMA_FROM_DEVICE); | |
| /* Swap the contents of the buffer */ | |
| buffer = kmap_atomic(sg->page, KM_BIO_SRC_IRQ) + sg->offset; | |
| pr_debug("buffer = %p, length = %d\n", buffer, sg->length); | |
| data->bytes_xfered += sg->length; | |
| len = sg->length / 4; | |
| for (index = 0; index < len; index++) { | |
| buffer[index] = swab32(buffer[index]); | |
| } | |
| kunmap_atomic(buffer, KM_BIO_SRC_IRQ); | |
| flush_dcache_page(sg->page); | |
| } | |
| /* Is there another transfer to trigger? */ | |
| if (host->transfer_index < data->sg_len) | |
| at91mci_pre_dma_read(host); | |
| else { | |
| at91_mci_write(AT91_MCI_IER, AT91_MCI_RXBUFF); | |
| at91_mci_write(AT91_PDC_PTCR, AT91_PDC_RXTDIS | AT91_PDC_TXTDIS); | |
| } | |
| pr_debug("post dma read done\n"); | |
| } | |
| /* | |
| * Handle transmitted data | |
| */ | |
| static void at91_mci_handle_transmitted(struct at91mci_host *host) | |
| { | |
| struct mmc_command *cmd; | |
| struct mmc_data *data; | |
| pr_debug("Handling the transmit\n"); | |
| /* Disable the transfer */ | |
| at91_mci_write(AT91_PDC_PTCR, AT91_PDC_RXTDIS | AT91_PDC_TXTDIS); | |
| /* Now wait for cmd ready */ | |
| at91_mci_write(AT91_MCI_IDR, AT91_MCI_TXBUFE); | |
| at91_mci_write(AT91_MCI_IER, AT91_MCI_NOTBUSY); | |
| cmd = host->cmd; | |
| if (!cmd) return; | |
| data = cmd->data; | |
| if (!data) return; | |
| data->bytes_xfered = host->total_length; | |
| } | |
| /* | |
| * Enable the controller | |
| */ | |
| static void at91_mci_enable(void) | |
| { | |
| at91_mci_write(AT91_MCI_CR, AT91_MCI_MCIEN); | |
| at91_mci_write(AT91_MCI_IDR, 0xFFFFFFFF); | |
| at91_mci_write(AT91_MCI_DTOR, AT91_MCI_DTOMUL_1M | AT91_MCI_DTOCYC); | |
| at91_mci_write(AT91_MCI_MR, 0x834A); | |
| at91_mci_write(AT91_MCI_SDCR, 0x0); | |
| } | |
| /* | |
| * Disable the controller | |
| */ | |
| static void at91_mci_disable(void) | |
| { | |
| at91_mci_write(AT91_MCI_CR, AT91_MCI_MCIDIS | AT91_MCI_SWRST); | |
| } | |
| /* | |
| * Send a command | |
| * return the interrupts to enable | |
| */ | |
| static unsigned int at91_mci_send_command(struct at91mci_host *host, struct mmc_command *cmd) | |
| { | |
| unsigned int cmdr, mr; | |
| unsigned int block_length; | |
| struct mmc_data *data = cmd->data; | |
| unsigned int blocks; | |
| unsigned int ier = 0; | |
| host->cmd = cmd; | |
| /* Not sure if this is needed */ | |
| #if 0 | |
| if ((at91_mci_read(AT91_MCI_SR) & AT91_MCI_RTOE) && (cmd->opcode == 1)) { | |
| pr_debug("Clearing timeout\n"); | |
| at91_mci_write(AT91_MCI_ARGR, 0); | |
| at91_mci_write(AT91_MCI_CMDR, AT91_MCI_OPDCMD); | |
| while (!(at91_mci_read(AT91_MCI_SR) & AT91_MCI_CMDRDY)) { | |
| /* spin */ | |
| pr_debug("Clearing: SR = %08X\n", at91_mci_read(AT91_MCI_SR)); | |
| } | |
| } | |
| #endif | |
| cmdr = cmd->opcode; | |
| if (mmc_resp_type(cmd) == MMC_RSP_NONE) | |
| cmdr |= AT91_MCI_RSPTYP_NONE; | |
| else { | |
| /* if a response is expected then allow maximum response latancy */ | |
| cmdr |= AT91_MCI_MAXLAT; | |
| /* set 136 bit response for R2, 48 bit response otherwise */ | |
| if (mmc_resp_type(cmd) == MMC_RSP_R2) | |
| cmdr |= AT91_MCI_RSPTYP_136; | |
| else | |
| cmdr |= AT91_MCI_RSPTYP_48; | |
| } | |
| if (data) { | |
| block_length = data->blksz; | |
| blocks = data->blocks; | |
| /* always set data start - also set direction flag for read */ | |
| if (data->flags & MMC_DATA_READ) | |
| cmdr |= (AT91_MCI_TRDIR | AT91_MCI_TRCMD_START); | |
| else if (data->flags & MMC_DATA_WRITE) | |
| cmdr |= AT91_MCI_TRCMD_START; | |
| if (data->flags & MMC_DATA_STREAM) | |
| cmdr |= AT91_MCI_TRTYP_STREAM; | |
| if (data->flags & MMC_DATA_MULTI) | |
| cmdr |= AT91_MCI_TRTYP_MULTIPLE; | |
| } | |
| else { | |
| block_length = 0; | |
| blocks = 0; | |
| } | |
| if (cmd->opcode == MMC_STOP_TRANSMISSION) | |
| cmdr |= AT91_MCI_TRCMD_STOP; | |
| if (host->bus_mode == MMC_BUSMODE_OPENDRAIN) | |
| cmdr |= AT91_MCI_OPDCMD; | |
| /* | |
| * Set the arguments and send the command | |
| */ | |
| pr_debug("Sending command %d as %08X, arg = %08X, blocks = %d, length = %d (MR = %08lX)\n", | |
| cmd->opcode, cmdr, cmd->arg, blocks, block_length, at91_mci_read(AT91_MCI_MR)); | |
| if (!data) { | |
| at91_mci_write(AT91_PDC_PTCR, AT91_PDC_TXTDIS | AT91_PDC_RXTDIS); | |
| at91_mci_write(AT91_PDC_RPR, 0); | |
| at91_mci_write(AT91_PDC_RCR, 0); | |
| at91_mci_write(AT91_PDC_RNPR, 0); | |
| at91_mci_write(AT91_PDC_RNCR, 0); | |
| at91_mci_write(AT91_PDC_TPR, 0); | |
| at91_mci_write(AT91_PDC_TCR, 0); | |
| at91_mci_write(AT91_PDC_TNPR, 0); | |
| at91_mci_write(AT91_PDC_TNCR, 0); | |
| at91_mci_write(AT91_MCI_ARGR, cmd->arg); | |
| at91_mci_write(AT91_MCI_CMDR, cmdr); | |
| return AT91_MCI_CMDRDY; | |
| } | |
| mr = at91_mci_read(AT91_MCI_MR) & 0x7fff; /* zero block length and PDC mode */ | |
| at91_mci_write(AT91_MCI_MR, mr | (block_length << 16) | AT91_MCI_PDCMODE); | |
| /* | |
| * Disable the PDC controller | |
| */ | |
| at91_mci_write(AT91_PDC_PTCR, AT91_PDC_RXTDIS | AT91_PDC_TXTDIS); | |
| if (cmdr & AT91_MCI_TRCMD_START) { | |
| data->bytes_xfered = 0; | |
| host->transfer_index = 0; | |
| host->in_use_index = 0; | |
| if (cmdr & AT91_MCI_TRDIR) { | |
| /* | |
| * Handle a read | |
| */ | |
| host->buffer = NULL; | |
| host->total_length = 0; | |
| at91mci_pre_dma_read(host); | |
| ier = AT91_MCI_ENDRX /* | AT91_MCI_RXBUFF */; | |
| } | |
| else { | |
| /* | |
| * Handle a write | |
| */ | |
| host->total_length = block_length * blocks; | |
| host->buffer = dma_alloc_coherent(NULL, | |
| host->total_length, | |
| &host->physical_address, GFP_KERNEL); | |
| at91mci_sg_to_dma(host, data); | |
| pr_debug("Transmitting %d bytes\n", host->total_length); | |
| at91_mci_write(AT91_PDC_TPR, host->physical_address); | |
| at91_mci_write(AT91_PDC_TCR, host->total_length / 4); | |
| ier = AT91_MCI_TXBUFE; | |
| } | |
| } | |
| /* | |
| * Send the command and then enable the PDC - not the other way round as | |
| * the data sheet says | |
| */ | |
| at91_mci_write(AT91_MCI_ARGR, cmd->arg); | |
| at91_mci_write(AT91_MCI_CMDR, cmdr); | |
| if (cmdr & AT91_MCI_TRCMD_START) { | |
| if (cmdr & AT91_MCI_TRDIR) | |
| at91_mci_write(AT91_PDC_PTCR, AT91_PDC_RXTEN); | |
| else | |
| at91_mci_write(AT91_PDC_PTCR, AT91_PDC_TXTEN); | |
| } | |
| return ier; | |
| } | |
| /* | |
| * Wait for a command to complete | |
| */ | |
| static void at91mci_process_command(struct at91mci_host *host, struct mmc_command *cmd) | |
| { | |
| unsigned int ier; | |
| ier = at91_mci_send_command(host, cmd); | |
| pr_debug("setting ier to %08X\n", ier); | |
| /* Stop on errors or the required value */ | |
| at91_mci_write(AT91_MCI_IER, 0xffff0000 | ier); | |
| } | |
| /* | |
| * Process the next step in the request | |
| */ | |
| static void at91mci_process_next(struct at91mci_host *host) | |
| { | |
| if (!(host->flags & FL_SENT_COMMAND)) { | |
| host->flags |= FL_SENT_COMMAND; | |
| at91mci_process_command(host, host->request->cmd); | |
| } | |
| else if ((!(host->flags & FL_SENT_STOP)) && host->request->stop) { | |
| host->flags |= FL_SENT_STOP; | |
| at91mci_process_command(host, host->request->stop); | |
| } | |
| else | |
| mmc_request_done(host->mmc, host->request); | |
| } | |
| /* | |
| * Handle a command that has been completed | |
| */ | |
| static void at91mci_completed_command(struct at91mci_host *host) | |
| { | |
| struct mmc_command *cmd = host->cmd; | |
| unsigned int status; | |
| at91_mci_write(AT91_MCI_IDR, 0xffffffff); | |
| cmd->resp[0] = at91_mci_read(AT91_MCI_RSPR(0)); | |
| cmd->resp[1] = at91_mci_read(AT91_MCI_RSPR(1)); | |
| cmd->resp[2] = at91_mci_read(AT91_MCI_RSPR(2)); | |
| cmd->resp[3] = at91_mci_read(AT91_MCI_RSPR(3)); | |
| if (host->buffer) { | |
| dma_free_coherent(NULL, host->total_length, host->buffer, host->physical_address); | |
| host->buffer = NULL; | |
| } | |
| status = at91_mci_read(AT91_MCI_SR); | |
| pr_debug("Status = %08X [%08X %08X %08X %08X]\n", | |
| status, cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3]); | |
| if (status & (AT91_MCI_RINDE | AT91_MCI_RDIRE | AT91_MCI_RCRCE | | |
| AT91_MCI_RENDE | AT91_MCI_RTOE | AT91_MCI_DCRCE | | |
| AT91_MCI_DTOE | AT91_MCI_OVRE | AT91_MCI_UNRE)) { | |
| if ((status & AT91_MCI_RCRCE) && | |
| ((cmd->opcode == MMC_SEND_OP_COND) || (cmd->opcode == SD_APP_OP_COND))) { | |
| cmd->error = MMC_ERR_NONE; | |
| } | |
| else { | |
| if (status & (AT91_MCI_RTOE | AT91_MCI_DTOE)) | |
| cmd->error = MMC_ERR_TIMEOUT; | |
| else if (status & (AT91_MCI_RCRCE | AT91_MCI_DCRCE)) | |
| cmd->error = MMC_ERR_BADCRC; | |
| else if (status & (AT91_MCI_OVRE | AT91_MCI_UNRE)) | |
| cmd->error = MMC_ERR_FIFO; | |
| else | |
| cmd->error = MMC_ERR_FAILED; | |
| pr_debug("Error detected and set to %d (cmd = %d, retries = %d)\n", | |
| cmd->error, cmd->opcode, cmd->retries); | |
| } | |
| } | |
| else | |
| cmd->error = MMC_ERR_NONE; | |
| at91mci_process_next(host); | |
| } | |
| /* | |
| * Handle an MMC request | |
| */ | |
| static void at91_mci_request(struct mmc_host *mmc, struct mmc_request *mrq) | |
| { | |
| struct at91mci_host *host = mmc_priv(mmc); | |
| host->request = mrq; | |
| host->flags = 0; | |
| at91mci_process_next(host); | |
| } | |
| /* | |
| * Set the IOS | |
| */ | |
| static void at91_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) | |
| { | |
| int clkdiv; | |
| struct at91mci_host *host = mmc_priv(mmc); | |
| unsigned long at91_master_clock = clk_get_rate(mci_clk); | |
| host->bus_mode = ios->bus_mode; | |
| if (ios->clock == 0) { | |
| /* Disable the MCI controller */ | |
| at91_mci_write(AT91_MCI_CR, AT91_MCI_MCIDIS); | |
| clkdiv = 0; | |
| } | |
| else { | |
| /* Enable the MCI controller */ | |
| at91_mci_write(AT91_MCI_CR, AT91_MCI_MCIEN); | |
| if ((at91_master_clock % (ios->clock * 2)) == 0) | |
| clkdiv = ((at91_master_clock / ios->clock) / 2) - 1; | |
| else | |
| clkdiv = (at91_master_clock / ios->clock) / 2; | |
| pr_debug("clkdiv = %d. mcck = %ld\n", clkdiv, | |
| at91_master_clock / (2 * (clkdiv + 1))); | |
| } | |
| if (ios->bus_width == MMC_BUS_WIDTH_4 && host->board->wire4) { | |
| pr_debug("MMC: Setting controller bus width to 4\n"); | |
| at91_mci_write(AT91_MCI_SDCR, at91_mci_read(AT91_MCI_SDCR) | AT91_MCI_SDCBUS); | |
| } | |
| else { | |
| pr_debug("MMC: Setting controller bus width to 1\n"); | |
| at91_mci_write(AT91_MCI_SDCR, at91_mci_read(AT91_MCI_SDCR) & ~AT91_MCI_SDCBUS); | |
| } | |
| /* Set the clock divider */ | |
| at91_mci_write(AT91_MCI_MR, (at91_mci_read(AT91_MCI_MR) & ~AT91_MCI_CLKDIV) | clkdiv); | |
| /* maybe switch power to the card */ | |
| if (host->board->vcc_pin) { | |
| switch (ios->power_mode) { | |
| case MMC_POWER_OFF: | |
| at91_set_gpio_output(host->board->vcc_pin, 0); | |
| break; | |
| case MMC_POWER_UP: | |
| case MMC_POWER_ON: | |
| at91_set_gpio_output(host->board->vcc_pin, 1); | |
| break; | |
| } | |
| } | |
| } | |
| /* | |
| * Handle an interrupt | |
| */ | |
| static irqreturn_t at91_mci_irq(int irq, void *devid) | |
| { | |
| struct at91mci_host *host = devid; | |
| int completed = 0; | |
| unsigned int int_status; | |
| int_status = at91_mci_read(AT91_MCI_SR); | |
| pr_debug("MCI irq: status = %08X, %08lX, %08lX\n", int_status, at91_mci_read(AT91_MCI_IMR), | |
| int_status & at91_mci_read(AT91_MCI_IMR)); | |
| if ((int_status & at91_mci_read(AT91_MCI_IMR)) & 0xffff0000) | |
| completed = 1; | |
| int_status &= at91_mci_read(AT91_MCI_IMR); | |
| if (int_status & AT91_MCI_UNRE) | |
| pr_debug("MMC: Underrun error\n"); | |
| if (int_status & AT91_MCI_OVRE) | |
| pr_debug("MMC: Overrun error\n"); | |
| if (int_status & AT91_MCI_DTOE) | |
| pr_debug("MMC: Data timeout\n"); | |
| if (int_status & AT91_MCI_DCRCE) | |
| pr_debug("MMC: CRC error in data\n"); | |
| if (int_status & AT91_MCI_RTOE) | |
| pr_debug("MMC: Response timeout\n"); | |
| if (int_status & AT91_MCI_RENDE) | |
| pr_debug("MMC: Response end bit error\n"); | |
| if (int_status & AT91_MCI_RCRCE) | |
| pr_debug("MMC: Response CRC error\n"); | |
| if (int_status & AT91_MCI_RDIRE) | |
| pr_debug("MMC: Response direction error\n"); | |
| if (int_status & AT91_MCI_RINDE) | |
| pr_debug("MMC: Response index error\n"); | |
| /* Only continue processing if no errors */ | |
| if (!completed) { | |
| if (int_status & AT91_MCI_TXBUFE) { | |
| pr_debug("TX buffer empty\n"); | |
| at91_mci_handle_transmitted(host); | |
| } | |
| if (int_status & AT91_MCI_RXBUFF) { | |
| pr_debug("RX buffer full\n"); | |
| at91_mci_write(AT91_MCI_IER, AT91_MCI_CMDRDY); | |
| } | |
| if (int_status & AT91_MCI_ENDTX) { | |
| pr_debug("Transmit has ended\n"); | |
| } | |
| if (int_status & AT91_MCI_ENDRX) { | |
| pr_debug("Receive has ended\n"); | |
| at91mci_post_dma_read(host); | |
| } | |
| if (int_status & AT91_MCI_NOTBUSY) { | |
| pr_debug("Card is ready\n"); | |
| at91_mci_write(AT91_MCI_IER, AT91_MCI_CMDRDY); | |
| } | |
| if (int_status & AT91_MCI_DTIP) { | |
| pr_debug("Data transfer in progress\n"); | |
| } | |
| if (int_status & AT91_MCI_BLKE) { | |
| pr_debug("Block transfer has ended\n"); | |
| } | |
| if (int_status & AT91_MCI_TXRDY) { | |
| pr_debug("Ready to transmit\n"); | |
| } | |
| if (int_status & AT91_MCI_RXRDY) { | |
| pr_debug("Ready to receive\n"); | |
| } | |
| if (int_status & AT91_MCI_CMDRDY) { | |
| pr_debug("Command ready\n"); | |
| completed = 1; | |
| } | |
| } | |
| at91_mci_write(AT91_MCI_IDR, int_status); | |
| if (completed) { | |
| pr_debug("Completed command\n"); | |
| at91_mci_write(AT91_MCI_IDR, 0xffffffff); | |
| at91mci_completed_command(host); | |
| } | |
| return IRQ_HANDLED; | |
| } | |
| static irqreturn_t at91_mmc_det_irq(int irq, void *_host) | |
| { | |
| struct at91mci_host *host = _host; | |
| int present = !at91_get_gpio_value(irq); | |
| /* | |
| * we expect this irq on both insert and remove, | |
| * and use a short delay to debounce. | |
| */ | |
| if (present != host->present) { | |
| host->present = present; | |
| pr_debug("%s: card %s\n", mmc_hostname(host->mmc), | |
| present ? "insert" : "remove"); | |
| if (!present) { | |
| pr_debug("****** Resetting SD-card bus width ******\n"); | |
| at91_mci_write(AT91_MCI_SDCR, 0); | |
| } | |
| mmc_detect_change(host->mmc, msecs_to_jiffies(100)); | |
| } | |
| return IRQ_HANDLED; | |
| } | |
| int at91_mci_get_ro(struct mmc_host *mmc) | |
| { | |
| int read_only = 0; | |
| struct at91mci_host *host = mmc_priv(mmc); | |
| if (host->board->wp_pin) { | |
| read_only = at91_get_gpio_value(host->board->wp_pin); | |
| printk(KERN_WARNING "%s: card is %s\n", mmc_hostname(mmc), | |
| (read_only ? "read-only" : "read-write") ); | |
| } | |
| else { | |
| printk(KERN_WARNING "%s: host does not support reading read-only " | |
| "switch. Assuming write-enable.\n", mmc_hostname(mmc)); | |
| } | |
| return read_only; | |
| } | |
| static struct mmc_host_ops at91_mci_ops = { | |
| .request = at91_mci_request, | |
| .set_ios = at91_mci_set_ios, | |
| .get_ro = at91_mci_get_ro, | |
| }; | |
| /* | |
| * Probe for the device | |
| */ | |
| static int at91_mci_probe(struct platform_device *pdev) | |
| { | |
| struct mmc_host *mmc; | |
| struct at91mci_host *host; | |
| int ret; | |
| pr_debug("Probe MCI devices\n"); | |
| at91_mci_disable(); | |
| at91_mci_enable(); | |
| mmc = mmc_alloc_host(sizeof(struct at91mci_host), &pdev->dev); | |
| if (!mmc) { | |
| pr_debug("Failed to allocate mmc host\n"); | |
| return -ENOMEM; | |
| } | |
| mmc->ops = &at91_mci_ops; | |
| mmc->f_min = 375000; | |
| mmc->f_max = 25000000; | |
| mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; | |
| mmc->caps = MMC_CAP_BYTEBLOCK; | |
| host = mmc_priv(mmc); | |
| host->mmc = mmc; | |
| host->buffer = NULL; | |
| host->bus_mode = 0; | |
| host->board = pdev->dev.platform_data; | |
| if (host->board->wire4) { | |
| #ifdef SUPPORT_4WIRE | |
| mmc->caps |= MMC_CAP_4_BIT_DATA; | |
| #else | |
| printk("MMC: 4 wire bus mode not supported by this driver - using 1 wire\n"); | |
| #endif | |
| } | |
| /* | |
| * Get Clock | |
| */ | |
| mci_clk = clk_get(&pdev->dev, "mci_clk"); | |
| if (IS_ERR(mci_clk)) { | |
| printk(KERN_ERR "AT91 MMC: no clock defined.\n"); | |
| mmc_free_host(mmc); | |
| return -ENODEV; | |
| } | |
| clk_enable(mci_clk); /* Enable the peripheral clock */ | |
| /* | |
| * Allocate the MCI interrupt | |
| */ | |
| ret = request_irq(AT91RM9200_ID_MCI, at91_mci_irq, IRQF_SHARED, DRIVER_NAME, host); | |
| if (ret) { | |
| printk(KERN_ERR "Failed to request MCI interrupt\n"); | |
| clk_disable(mci_clk); | |
| clk_put(mci_clk); | |
| mmc_free_host(mmc); | |
| return ret; | |
| } | |
| platform_set_drvdata(pdev, mmc); | |
| /* | |
| * Add host to MMC layer | |
| */ | |
| if (host->board->det_pin) | |
| host->present = !at91_get_gpio_value(host->board->det_pin); | |
| else | |
| host->present = -1; | |
| mmc_add_host(mmc); | |
| /* | |
| * monitor card insertion/removal if we can | |
| */ | |
| if (host->board->det_pin) { | |
| ret = request_irq(host->board->det_pin, at91_mmc_det_irq, | |
| 0, DRIVER_NAME, host); | |
| if (ret) | |
| printk(KERN_ERR "couldn't allocate MMC detect irq\n"); | |
| } | |
| pr_debug(KERN_INFO "Added MCI driver\n"); | |
| return 0; | |
| } | |
| /* | |
| * Remove a device | |
| */ | |
| static int at91_mci_remove(struct platform_device *pdev) | |
| { | |
| struct mmc_host *mmc = platform_get_drvdata(pdev); | |
| struct at91mci_host *host; | |
| if (!mmc) | |
| return -1; | |
| host = mmc_priv(mmc); | |
| if (host->present != -1) { | |
| free_irq(host->board->det_pin, host); | |
| cancel_delayed_work(&host->mmc->detect); | |
| } | |
| mmc_remove_host(mmc); | |
| at91_mci_disable(); | |
| free_irq(AT91RM9200_ID_MCI, host); | |
| mmc_free_host(mmc); | |
| clk_disable(mci_clk); /* Disable the peripheral clock */ | |
| clk_put(mci_clk); | |
| platform_set_drvdata(pdev, NULL); | |
| pr_debug("MCI Removed\n"); | |
| return 0; | |
| } | |
| #ifdef CONFIG_PM | |
| static int at91_mci_suspend(struct platform_device *pdev, pm_message_t state) | |
| { | |
| struct mmc_host *mmc = platform_get_drvdata(pdev); | |
| int ret = 0; | |
| if (mmc) | |
| ret = mmc_suspend_host(mmc, state); | |
| return ret; | |
| } | |
| static int at91_mci_resume(struct platform_device *pdev) | |
| { | |
| struct mmc_host *mmc = platform_get_drvdata(pdev); | |
| int ret = 0; | |
| if (mmc) | |
| ret = mmc_resume_host(mmc); | |
| return ret; | |
| } | |
| #else | |
| #define at91_mci_suspend NULL | |
| #define at91_mci_resume NULL | |
| #endif | |
| static struct platform_driver at91_mci_driver = { | |
| .probe = at91_mci_probe, | |
| .remove = at91_mci_remove, | |
| .suspend = at91_mci_suspend, | |
| .resume = at91_mci_resume, | |
| .driver = { | |
| .name = DRIVER_NAME, | |
| .owner = THIS_MODULE, | |
| }, | |
| }; | |
| static int __init at91_mci_init(void) | |
| { | |
| return platform_driver_register(&at91_mci_driver); | |
| } | |
| static void __exit at91_mci_exit(void) | |
| { | |
| platform_driver_unregister(&at91_mci_driver); | |
| } | |
| module_init(at91_mci_init); | |
| module_exit(at91_mci_exit); | |
| MODULE_DESCRIPTION("AT91 Multimedia Card Interface driver"); | |
| MODULE_AUTHOR("Nick Randell"); | |
| MODULE_LICENSE("GPL"); |