| /* | |
| * drivers/mtd/nand.c | |
| * | |
| * Overview: | |
| * This is the generic MTD driver for NAND flash devices. It should be | |
| * capable of working with almost all NAND chips currently available. | |
| * Basic support for AG-AND chips is provided. | |
| * | |
| * Additional technical information is available on | |
| * http://www.linux-mtd.infradead.org/tech/nand.html | |
| * | |
| * Copyright (C) 2000 Steven J. Hill (sjhill@realitydiluted.com) | |
| * 2002-2006 Thomas Gleixner (tglx@linutronix.de) | |
| * | |
| * Credits: | |
| * David Woodhouse for adding multichip support | |
| * | |
| * Aleph One Ltd. and Toby Churchill Ltd. for supporting the | |
| * rework for 2K page size chips | |
| * | |
| * TODO: | |
| * Enable cached programming for 2k page size chips | |
| * Check, if mtd->ecctype should be set to MTD_ECC_HW | |
| * if we have HW ecc support. | |
| * The AG-AND chips have nice features for speed improvement, | |
| * which are not supported yet. Read / program 4 pages in one go. | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License version 2 as | |
| * published by the Free Software Foundation. | |
| * | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/delay.h> | |
| #include <linux/errno.h> | |
| #include <linux/err.h> | |
| #include <linux/sched.h> | |
| #include <linux/slab.h> | |
| #include <linux/types.h> | |
| #include <linux/mtd/mtd.h> | |
| #include <linux/mtd/nand.h> | |
| #include <linux/mtd/nand_ecc.h> | |
| #include <linux/mtd/compatmac.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/bitops.h> | |
| #include <linux/leds.h> | |
| #include <asm/io.h> | |
| #ifdef CONFIG_MTD_PARTITIONS | |
| #include <linux/mtd/partitions.h> | |
| #endif | |
| /* Define default oob placement schemes for large and small page devices */ | |
| static struct nand_ecclayout nand_oob_8 = { | |
| .eccbytes = 3, | |
| .eccpos = {0, 1, 2}, | |
| .oobfree = { | |
| {.offset = 3, | |
| .length = 2}, | |
| {.offset = 6, | |
| .length = 2}} | |
| }; | |
| static struct nand_ecclayout nand_oob_16 = { | |
| .eccbytes = 6, | |
| .eccpos = {0, 1, 2, 3, 6, 7}, | |
| .oobfree = { | |
| {.offset = 8, | |
| . length = 8}} | |
| }; | |
| static struct nand_ecclayout nand_oob_64 = { | |
| .eccbytes = 24, | |
| .eccpos = { | |
| 40, 41, 42, 43, 44, 45, 46, 47, | |
| 48, 49, 50, 51, 52, 53, 54, 55, | |
| 56, 57, 58, 59, 60, 61, 62, 63}, | |
| .oobfree = { | |
| {.offset = 2, | |
| .length = 38}} | |
| }; | |
| static int nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, | |
| int new_state); | |
| static int nand_do_write_oob(struct mtd_info *mtd, loff_t to, | |
| struct mtd_oob_ops *ops); | |
| /* | |
| * For devices which display every fart in the system on a seperate LED. Is | |
| * compiled away when LED support is disabled. | |
| */ | |
| DEFINE_LED_TRIGGER(nand_led_trigger); | |
| /** | |
| * nand_release_device - [GENERIC] release chip | |
| * @mtd: MTD device structure | |
| * | |
| * Deselect, release chip lock and wake up anyone waiting on the device | |
| */ | |
| static void nand_release_device(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| /* De-select the NAND device */ | |
| chip->select_chip(mtd, -1); | |
| /* Release the controller and the chip */ | |
| spin_lock(&chip->controller->lock); | |
| chip->controller->active = NULL; | |
| chip->state = FL_READY; | |
| wake_up(&chip->controller->wq); | |
| spin_unlock(&chip->controller->lock); | |
| } | |
| /** | |
| * nand_read_byte - [DEFAULT] read one byte from the chip | |
| * @mtd: MTD device structure | |
| * | |
| * Default read function for 8bit buswith | |
| */ | |
| static uint8_t nand_read_byte(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| return readb(chip->IO_ADDR_R); | |
| } | |
| /** | |
| * nand_read_byte16 - [DEFAULT] read one byte endianess aware from the chip | |
| * @mtd: MTD device structure | |
| * | |
| * Default read function for 16bit buswith with | |
| * endianess conversion | |
| */ | |
| static uint8_t nand_read_byte16(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| return (uint8_t) cpu_to_le16(readw(chip->IO_ADDR_R)); | |
| } | |
| /** | |
| * nand_read_word - [DEFAULT] read one word from the chip | |
| * @mtd: MTD device structure | |
| * | |
| * Default read function for 16bit buswith without | |
| * endianess conversion | |
| */ | |
| static u16 nand_read_word(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| return readw(chip->IO_ADDR_R); | |
| } | |
| /** | |
| * nand_select_chip - [DEFAULT] control CE line | |
| * @mtd: MTD device structure | |
| * @chipnr: chipnumber to select, -1 for deselect | |
| * | |
| * Default select function for 1 chip devices. | |
| */ | |
| static void nand_select_chip(struct mtd_info *mtd, int chipnr) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| switch (chipnr) { | |
| case -1: | |
| chip->cmd_ctrl(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE); | |
| break; | |
| case 0: | |
| break; | |
| default: | |
| BUG(); | |
| } | |
| } | |
| /** | |
| * nand_write_buf - [DEFAULT] write buffer to chip | |
| * @mtd: MTD device structure | |
| * @buf: data buffer | |
| * @len: number of bytes to write | |
| * | |
| * Default write function for 8bit buswith | |
| */ | |
| static void nand_write_buf(struct mtd_info *mtd, const uint8_t *buf, int len) | |
| { | |
| int i; | |
| struct nand_chip *chip = mtd->priv; | |
| for (i = 0; i < len; i++) | |
| writeb(buf[i], chip->IO_ADDR_W); | |
| } | |
| /** | |
| * nand_read_buf - [DEFAULT] read chip data into buffer | |
| * @mtd: MTD device structure | |
| * @buf: buffer to store date | |
| * @len: number of bytes to read | |
| * | |
| * Default read function for 8bit buswith | |
| */ | |
| static void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) | |
| { | |
| int i; | |
| struct nand_chip *chip = mtd->priv; | |
| for (i = 0; i < len; i++) | |
| buf[i] = readb(chip->IO_ADDR_R); | |
| } | |
| /** | |
| * nand_verify_buf - [DEFAULT] Verify chip data against buffer | |
| * @mtd: MTD device structure | |
| * @buf: buffer containing the data to compare | |
| * @len: number of bytes to compare | |
| * | |
| * Default verify function for 8bit buswith | |
| */ | |
| static int nand_verify_buf(struct mtd_info *mtd, const uint8_t *buf, int len) | |
| { | |
| int i; | |
| struct nand_chip *chip = mtd->priv; | |
| for (i = 0; i < len; i++) | |
| if (buf[i] != readb(chip->IO_ADDR_R)) | |
| return -EFAULT; | |
| return 0; | |
| } | |
| /** | |
| * nand_write_buf16 - [DEFAULT] write buffer to chip | |
| * @mtd: MTD device structure | |
| * @buf: data buffer | |
| * @len: number of bytes to write | |
| * | |
| * Default write function for 16bit buswith | |
| */ | |
| static void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len) | |
| { | |
| int i; | |
| struct nand_chip *chip = mtd->priv; | |
| u16 *p = (u16 *) buf; | |
| len >>= 1; | |
| for (i = 0; i < len; i++) | |
| writew(p[i], chip->IO_ADDR_W); | |
| } | |
| /** | |
| * nand_read_buf16 - [DEFAULT] read chip data into buffer | |
| * @mtd: MTD device structure | |
| * @buf: buffer to store date | |
| * @len: number of bytes to read | |
| * | |
| * Default read function for 16bit buswith | |
| */ | |
| static void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len) | |
| { | |
| int i; | |
| struct nand_chip *chip = mtd->priv; | |
| u16 *p = (u16 *) buf; | |
| len >>= 1; | |
| for (i = 0; i < len; i++) | |
| p[i] = readw(chip->IO_ADDR_R); | |
| } | |
| /** | |
| * nand_verify_buf16 - [DEFAULT] Verify chip data against buffer | |
| * @mtd: MTD device structure | |
| * @buf: buffer containing the data to compare | |
| * @len: number of bytes to compare | |
| * | |
| * Default verify function for 16bit buswith | |
| */ | |
| static int nand_verify_buf16(struct mtd_info *mtd, const uint8_t *buf, int len) | |
| { | |
| int i; | |
| struct nand_chip *chip = mtd->priv; | |
| u16 *p = (u16 *) buf; | |
| len >>= 1; | |
| for (i = 0; i < len; i++) | |
| if (p[i] != readw(chip->IO_ADDR_R)) | |
| return -EFAULT; | |
| return 0; | |
| } | |
| /** | |
| * nand_block_bad - [DEFAULT] Read bad block marker from the chip | |
| * @mtd: MTD device structure | |
| * @ofs: offset from device start | |
| * @getchip: 0, if the chip is already selected | |
| * | |
| * Check, if the block is bad. | |
| */ | |
| static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip) | |
| { | |
| int page, chipnr, res = 0; | |
| struct nand_chip *chip = mtd->priv; | |
| u16 bad; | |
| if (getchip) { | |
| page = (int)(ofs >> chip->page_shift); | |
| chipnr = (int)(ofs >> chip->chip_shift); | |
| nand_get_device(chip, mtd, FL_READING); | |
| /* Select the NAND device */ | |
| chip->select_chip(mtd, chipnr); | |
| } else | |
| page = (int)ofs; | |
| if (chip->options & NAND_BUSWIDTH_16) { | |
| chip->cmdfunc(mtd, NAND_CMD_READOOB, chip->badblockpos & 0xFE, | |
| page & chip->pagemask); | |
| bad = cpu_to_le16(chip->read_word(mtd)); | |
| if (chip->badblockpos & 0x1) | |
| bad >>= 8; | |
| if ((bad & 0xFF) != 0xff) | |
| res = 1; | |
| } else { | |
| chip->cmdfunc(mtd, NAND_CMD_READOOB, chip->badblockpos, | |
| page & chip->pagemask); | |
| if (chip->read_byte(mtd) != 0xff) | |
| res = 1; | |
| } | |
| if (getchip) | |
| nand_release_device(mtd); | |
| return res; | |
| } | |
| /** | |
| * nand_default_block_markbad - [DEFAULT] mark a block bad | |
| * @mtd: MTD device structure | |
| * @ofs: offset from device start | |
| * | |
| * This is the default implementation, which can be overridden by | |
| * a hardware specific driver. | |
| */ | |
| static int nand_default_block_markbad(struct mtd_info *mtd, loff_t ofs) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| uint8_t buf[2] = { 0, 0 }; | |
| int block, ret; | |
| /* Get block number */ | |
| block = ((int)ofs) >> chip->bbt_erase_shift; | |
| if (chip->bbt) | |
| chip->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1); | |
| /* Do we have a flash based bad block table ? */ | |
| if (chip->options & NAND_USE_FLASH_BBT) | |
| ret = nand_update_bbt(mtd, ofs); | |
| else { | |
| /* We write two bytes, so we dont have to mess with 16 bit | |
| * access | |
| */ | |
| ofs += mtd->oobsize; | |
| chip->ops.len = 2; | |
| chip->ops.datbuf = NULL; | |
| chip->ops.oobbuf = buf; | |
| chip->ops.ooboffs = chip->badblockpos & ~0x01; | |
| ret = nand_do_write_oob(mtd, ofs, &chip->ops); | |
| } | |
| if (!ret) | |
| mtd->ecc_stats.badblocks++; | |
| return ret; | |
| } | |
| /** | |
| * nand_check_wp - [GENERIC] check if the chip is write protected | |
| * @mtd: MTD device structure | |
| * Check, if the device is write protected | |
| * | |
| * The function expects, that the device is already selected | |
| */ | |
| static int nand_check_wp(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| /* Check the WP bit */ | |
| chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); | |
| return (chip->read_byte(mtd) & NAND_STATUS_WP) ? 0 : 1; | |
| } | |
| /** | |
| * nand_block_checkbad - [GENERIC] Check if a block is marked bad | |
| * @mtd: MTD device structure | |
| * @ofs: offset from device start | |
| * @getchip: 0, if the chip is already selected | |
| * @allowbbt: 1, if its allowed to access the bbt area | |
| * | |
| * Check, if the block is bad. Either by reading the bad block table or | |
| * calling of the scan function. | |
| */ | |
| static int nand_block_checkbad(struct mtd_info *mtd, loff_t ofs, int getchip, | |
| int allowbbt) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| if (!chip->bbt) | |
| return chip->block_bad(mtd, ofs, getchip); | |
| /* Return info from the table */ | |
| return nand_isbad_bbt(mtd, ofs, allowbbt); | |
| } | |
| /* | |
| * Wait for the ready pin, after a command | |
| * The timeout is catched later. | |
| */ | |
| void nand_wait_ready(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| unsigned long timeo = jiffies + 2; | |
| led_trigger_event(nand_led_trigger, LED_FULL); | |
| /* wait until command is processed or timeout occures */ | |
| do { | |
| if (chip->dev_ready(mtd)) | |
| break; | |
| touch_softlockup_watchdog(); | |
| } while (time_before(jiffies, timeo)); | |
| led_trigger_event(nand_led_trigger, LED_OFF); | |
| } | |
| EXPORT_SYMBOL_GPL(nand_wait_ready); | |
| /** | |
| * nand_command - [DEFAULT] Send command to NAND device | |
| * @mtd: MTD device structure | |
| * @command: the command to be sent | |
| * @column: the column address for this command, -1 if none | |
| * @page_addr: the page address for this command, -1 if none | |
| * | |
| * Send command to NAND device. This function is used for small page | |
| * devices (256/512 Bytes per page) | |
| */ | |
| static void nand_command(struct mtd_info *mtd, unsigned int command, | |
| int column, int page_addr) | |
| { | |
| register struct nand_chip *chip = mtd->priv; | |
| int ctrl = NAND_CTRL_CLE | NAND_CTRL_CHANGE; | |
| /* | |
| * Write out the command to the device. | |
| */ | |
| if (command == NAND_CMD_SEQIN) { | |
| int readcmd; | |
| if (column >= mtd->writesize) { | |
| /* OOB area */ | |
| column -= mtd->writesize; | |
| readcmd = NAND_CMD_READOOB; | |
| } else if (column < 256) { | |
| /* First 256 bytes --> READ0 */ | |
| readcmd = NAND_CMD_READ0; | |
| } else { | |
| column -= 256; | |
| readcmd = NAND_CMD_READ1; | |
| } | |
| chip->cmd_ctrl(mtd, readcmd, ctrl); | |
| ctrl &= ~NAND_CTRL_CHANGE; | |
| } | |
| chip->cmd_ctrl(mtd, command, ctrl); | |
| /* | |
| * Address cycle, when necessary | |
| */ | |
| ctrl = NAND_CTRL_ALE | NAND_CTRL_CHANGE; | |
| /* Serially input address */ | |
| if (column != -1) { | |
| /* Adjust columns for 16 bit buswidth */ | |
| if (chip->options & NAND_BUSWIDTH_16) | |
| column >>= 1; | |
| chip->cmd_ctrl(mtd, column, ctrl); | |
| ctrl &= ~NAND_CTRL_CHANGE; | |
| } | |
| if (page_addr != -1) { | |
| chip->cmd_ctrl(mtd, page_addr, ctrl); | |
| ctrl &= ~NAND_CTRL_CHANGE; | |
| chip->cmd_ctrl(mtd, page_addr >> 8, ctrl); | |
| /* One more address cycle for devices > 32MiB */ | |
| if (chip->chipsize > (32 << 20)) | |
| chip->cmd_ctrl(mtd, page_addr >> 16, ctrl); | |
| } | |
| chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); | |
| /* | |
| * program and erase have their own busy handlers | |
| * status and sequential in needs no delay | |
| */ | |
| switch (command) { | |
| case NAND_CMD_PAGEPROG: | |
| case NAND_CMD_ERASE1: | |
| case NAND_CMD_ERASE2: | |
| case NAND_CMD_SEQIN: | |
| case NAND_CMD_STATUS: | |
| return; | |
| case NAND_CMD_RESET: | |
| if (chip->dev_ready) | |
| break; | |
| udelay(chip->chip_delay); | |
| chip->cmd_ctrl(mtd, NAND_CMD_STATUS, | |
| NAND_CTRL_CLE | NAND_CTRL_CHANGE); | |
| chip->cmd_ctrl(mtd, | |
| NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); | |
| while (!(chip->read_byte(mtd) & NAND_STATUS_READY)) ; | |
| return; | |
| /* This applies to read commands */ | |
| default: | |
| /* | |
| * If we don't have access to the busy pin, we apply the given | |
| * command delay | |
| */ | |
| if (!chip->dev_ready) { | |
| udelay(chip->chip_delay); | |
| return; | |
| } | |
| } | |
| /* Apply this short delay always to ensure that we do wait tWB in | |
| * any case on any machine. */ | |
| ndelay(100); | |
| nand_wait_ready(mtd); | |
| } | |
| /** | |
| * nand_command_lp - [DEFAULT] Send command to NAND large page device | |
| * @mtd: MTD device structure | |
| * @command: the command to be sent | |
| * @column: the column address for this command, -1 if none | |
| * @page_addr: the page address for this command, -1 if none | |
| * | |
| * Send command to NAND device. This is the version for the new large page | |
| * devices We dont have the separate regions as we have in the small page | |
| * devices. We must emulate NAND_CMD_READOOB to keep the code compatible. | |
| */ | |
| static void nand_command_lp(struct mtd_info *mtd, unsigned int command, | |
| int column, int page_addr) | |
| { | |
| register struct nand_chip *chip = mtd->priv; | |
| /* Emulate NAND_CMD_READOOB */ | |
| if (command == NAND_CMD_READOOB) { | |
| column += mtd->writesize; | |
| command = NAND_CMD_READ0; | |
| } | |
| /* Command latch cycle */ | |
| chip->cmd_ctrl(mtd, command & 0xff, | |
| NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); | |
| if (column != -1 || page_addr != -1) { | |
| int ctrl = NAND_CTRL_CHANGE | NAND_NCE | NAND_ALE; | |
| /* Serially input address */ | |
| if (column != -1) { | |
| /* Adjust columns for 16 bit buswidth */ | |
| if (chip->options & NAND_BUSWIDTH_16) | |
| column >>= 1; | |
| chip->cmd_ctrl(mtd, column, ctrl); | |
| ctrl &= ~NAND_CTRL_CHANGE; | |
| chip->cmd_ctrl(mtd, column >> 8, ctrl); | |
| } | |
| if (page_addr != -1) { | |
| chip->cmd_ctrl(mtd, page_addr, ctrl); | |
| chip->cmd_ctrl(mtd, page_addr >> 8, | |
| NAND_NCE | NAND_ALE); | |
| /* One more address cycle for devices > 128MiB */ | |
| if (chip->chipsize > (128 << 20)) | |
| chip->cmd_ctrl(mtd, page_addr >> 16, | |
| NAND_NCE | NAND_ALE); | |
| } | |
| } | |
| chip->cmd_ctrl(mtd, NAND_CMD_NONE, NAND_NCE | NAND_CTRL_CHANGE); | |
| /* | |
| * program and erase have their own busy handlers | |
| * status, sequential in, and deplete1 need no delay | |
| */ | |
| switch (command) { | |
| case NAND_CMD_CACHEDPROG: | |
| case NAND_CMD_PAGEPROG: | |
| case NAND_CMD_ERASE1: | |
| case NAND_CMD_ERASE2: | |
| case NAND_CMD_SEQIN: | |
| case NAND_CMD_RNDIN: | |
| case NAND_CMD_STATUS: | |
| case NAND_CMD_DEPLETE1: | |
| return; | |
| /* | |
| * read error status commands require only a short delay | |
| */ | |
| case NAND_CMD_STATUS_ERROR: | |
| case NAND_CMD_STATUS_ERROR0: | |
| case NAND_CMD_STATUS_ERROR1: | |
| case NAND_CMD_STATUS_ERROR2: | |
| case NAND_CMD_STATUS_ERROR3: | |
| udelay(chip->chip_delay); | |
| return; | |
| case NAND_CMD_RESET: | |
| if (chip->dev_ready) | |
| break; | |
| udelay(chip->chip_delay); | |
| chip->cmd_ctrl(mtd, NAND_CMD_STATUS, | |
| NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); | |
| chip->cmd_ctrl(mtd, NAND_CMD_NONE, | |
| NAND_NCE | NAND_CTRL_CHANGE); | |
| while (!(chip->read_byte(mtd) & NAND_STATUS_READY)) ; | |
| return; | |
| case NAND_CMD_RNDOUT: | |
| /* No ready / busy check necessary */ | |
| chip->cmd_ctrl(mtd, NAND_CMD_RNDOUTSTART, | |
| NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); | |
| chip->cmd_ctrl(mtd, NAND_CMD_NONE, | |
| NAND_NCE | NAND_CTRL_CHANGE); | |
| return; | |
| case NAND_CMD_READ0: | |
| chip->cmd_ctrl(mtd, NAND_CMD_READSTART, | |
| NAND_NCE | NAND_CLE | NAND_CTRL_CHANGE); | |
| chip->cmd_ctrl(mtd, NAND_CMD_NONE, | |
| NAND_NCE | NAND_CTRL_CHANGE); | |
| /* This applies to read commands */ | |
| default: | |
| /* | |
| * If we don't have access to the busy pin, we apply the given | |
| * command delay | |
| */ | |
| if (!chip->dev_ready) { | |
| udelay(chip->chip_delay); | |
| return; | |
| } | |
| } | |
| /* Apply this short delay always to ensure that we do wait tWB in | |
| * any case on any machine. */ | |
| ndelay(100); | |
| nand_wait_ready(mtd); | |
| } | |
| /** | |
| * nand_get_device - [GENERIC] Get chip for selected access | |
| * @chip: the nand chip descriptor | |
| * @mtd: MTD device structure | |
| * @new_state: the state which is requested | |
| * | |
| * Get the device and lock it for exclusive access | |
| */ | |
| static int | |
| nand_get_device(struct nand_chip *chip, struct mtd_info *mtd, int new_state) | |
| { | |
| spinlock_t *lock = &chip->controller->lock; | |
| wait_queue_head_t *wq = &chip->controller->wq; | |
| DECLARE_WAITQUEUE(wait, current); | |
| retry: | |
| spin_lock(lock); | |
| /* Hardware controller shared among independend devices */ | |
| /* Hardware controller shared among independend devices */ | |
| if (!chip->controller->active) | |
| chip->controller->active = chip; | |
| if (chip->controller->active == chip && chip->state == FL_READY) { | |
| chip->state = new_state; | |
| spin_unlock(lock); | |
| return 0; | |
| } | |
| if (new_state == FL_PM_SUSPENDED) { | |
| spin_unlock(lock); | |
| return (chip->state == FL_PM_SUSPENDED) ? 0 : -EAGAIN; | |
| } | |
| set_current_state(TASK_UNINTERRUPTIBLE); | |
| add_wait_queue(wq, &wait); | |
| spin_unlock(lock); | |
| schedule(); | |
| remove_wait_queue(wq, &wait); | |
| goto retry; | |
| } | |
| /** | |
| * nand_wait - [DEFAULT] wait until the command is done | |
| * @mtd: MTD device structure | |
| * @chip: NAND chip structure | |
| * | |
| * Wait for command done. This applies to erase and program only | |
| * Erase can take up to 400ms and program up to 20ms according to | |
| * general NAND and SmartMedia specs | |
| */ | |
| static int nand_wait(struct mtd_info *mtd, struct nand_chip *chip) | |
| { | |
| unsigned long timeo = jiffies; | |
| int status, state = chip->state; | |
| if (state == FL_ERASING) | |
| timeo += (HZ * 400) / 1000; | |
| else | |
| timeo += (HZ * 20) / 1000; | |
| led_trigger_event(nand_led_trigger, LED_FULL); | |
| /* Apply this short delay always to ensure that we do wait tWB in | |
| * any case on any machine. */ | |
| ndelay(100); | |
| if ((state == FL_ERASING) && (chip->options & NAND_IS_AND)) | |
| chip->cmdfunc(mtd, NAND_CMD_STATUS_MULTI, -1, -1); | |
| else | |
| chip->cmdfunc(mtd, NAND_CMD_STATUS, -1, -1); | |
| while (time_before(jiffies, timeo)) { | |
| if (chip->dev_ready) { | |
| if (chip->dev_ready(mtd)) | |
| break; | |
| } else { | |
| if (chip->read_byte(mtd) & NAND_STATUS_READY) | |
| break; | |
| } | |
| cond_resched(); | |
| } | |
| led_trigger_event(nand_led_trigger, LED_OFF); | |
| status = (int)chip->read_byte(mtd); | |
| return status; | |
| } | |
| /** | |
| * nand_read_page_raw - [Intern] read raw page data without ecc | |
| * @mtd: mtd info structure | |
| * @chip: nand chip info structure | |
| * @buf: buffer to store read data | |
| */ | |
| static int nand_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip, | |
| uint8_t *buf) | |
| { | |
| chip->read_buf(mtd, buf, mtd->writesize); | |
| chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); | |
| return 0; | |
| } | |
| /** | |
| * nand_read_page_swecc - {REPLACABLE] software ecc based page read function | |
| * @mtd: mtd info structure | |
| * @chip: nand chip info structure | |
| * @buf: buffer to store read data | |
| */ | |
| static int nand_read_page_swecc(struct mtd_info *mtd, struct nand_chip *chip, | |
| uint8_t *buf) | |
| { | |
| int i, eccsize = chip->ecc.size; | |
| int eccbytes = chip->ecc.bytes; | |
| int eccsteps = chip->ecc.steps; | |
| uint8_t *p = buf; | |
| uint8_t *ecc_calc = chip->buffers->ecccalc; | |
| uint8_t *ecc_code = chip->buffers->ecccode; | |
| int *eccpos = chip->ecc.layout->eccpos; | |
| nand_read_page_raw(mtd, chip, buf); | |
| for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) | |
| chip->ecc.calculate(mtd, p, &ecc_calc[i]); | |
| for (i = 0; i < chip->ecc.total; i++) | |
| ecc_code[i] = chip->oob_poi[eccpos[i]]; | |
| eccsteps = chip->ecc.steps; | |
| p = buf; | |
| for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { | |
| int stat; | |
| stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]); | |
| if (stat == -1) | |
| mtd->ecc_stats.failed++; | |
| else | |
| mtd->ecc_stats.corrected += stat; | |
| } | |
| return 0; | |
| } | |
| /** | |
| * nand_read_page_hwecc - {REPLACABLE] hardware ecc based page read function | |
| * @mtd: mtd info structure | |
| * @chip: nand chip info structure | |
| * @buf: buffer to store read data | |
| * | |
| * Not for syndrome calculating ecc controllers which need a special oob layout | |
| */ | |
| static int nand_read_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, | |
| uint8_t *buf) | |
| { | |
| int i, eccsize = chip->ecc.size; | |
| int eccbytes = chip->ecc.bytes; | |
| int eccsteps = chip->ecc.steps; | |
| uint8_t *p = buf; | |
| uint8_t *ecc_calc = chip->buffers->ecccalc; | |
| uint8_t *ecc_code = chip->buffers->ecccode; | |
| int *eccpos = chip->ecc.layout->eccpos; | |
| for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { | |
| chip->ecc.hwctl(mtd, NAND_ECC_READ); | |
| chip->read_buf(mtd, p, eccsize); | |
| chip->ecc.calculate(mtd, p, &ecc_calc[i]); | |
| } | |
| chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); | |
| for (i = 0; i < chip->ecc.total; i++) | |
| ecc_code[i] = chip->oob_poi[eccpos[i]]; | |
| eccsteps = chip->ecc.steps; | |
| p = buf; | |
| for (i = 0 ; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { | |
| int stat; | |
| stat = chip->ecc.correct(mtd, p, &ecc_code[i], &ecc_calc[i]); | |
| if (stat == -1) | |
| mtd->ecc_stats.failed++; | |
| else | |
| mtd->ecc_stats.corrected += stat; | |
| } | |
| return 0; | |
| } | |
| /** | |
| * nand_read_page_syndrome - {REPLACABLE] hardware ecc syndrom based page read | |
| * @mtd: mtd info structure | |
| * @chip: nand chip info structure | |
| * @buf: buffer to store read data | |
| * | |
| * The hw generator calculates the error syndrome automatically. Therefor | |
| * we need a special oob layout and handling. | |
| */ | |
| static int nand_read_page_syndrome(struct mtd_info *mtd, struct nand_chip *chip, | |
| uint8_t *buf) | |
| { | |
| int i, eccsize = chip->ecc.size; | |
| int eccbytes = chip->ecc.bytes; | |
| int eccsteps = chip->ecc.steps; | |
| uint8_t *p = buf; | |
| uint8_t *oob = chip->oob_poi; | |
| for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { | |
| int stat; | |
| chip->ecc.hwctl(mtd, NAND_ECC_READ); | |
| chip->read_buf(mtd, p, eccsize); | |
| if (chip->ecc.prepad) { | |
| chip->read_buf(mtd, oob, chip->ecc.prepad); | |
| oob += chip->ecc.prepad; | |
| } | |
| chip->ecc.hwctl(mtd, NAND_ECC_READSYN); | |
| chip->read_buf(mtd, oob, eccbytes); | |
| stat = chip->ecc.correct(mtd, p, oob, NULL); | |
| if (stat == -1) | |
| mtd->ecc_stats.failed++; | |
| else | |
| mtd->ecc_stats.corrected += stat; | |
| oob += eccbytes; | |
| if (chip->ecc.postpad) { | |
| chip->read_buf(mtd, oob, chip->ecc.postpad); | |
| oob += chip->ecc.postpad; | |
| } | |
| } | |
| /* Calculate remaining oob bytes */ | |
| i = mtd->oobsize - (oob - chip->oob_poi); | |
| if (i) | |
| chip->read_buf(mtd, oob, i); | |
| return 0; | |
| } | |
| /** | |
| * nand_transfer_oob - [Internal] Transfer oob to client buffer | |
| * @chip: nand chip structure | |
| * @oob: oob destination address | |
| * @ops: oob ops structure | |
| */ | |
| static uint8_t *nand_transfer_oob(struct nand_chip *chip, uint8_t *oob, | |
| struct mtd_oob_ops *ops) | |
| { | |
| size_t len = ops->ooblen; | |
| switch(ops->mode) { | |
| case MTD_OOB_PLACE: | |
| case MTD_OOB_RAW: | |
| memcpy(oob, chip->oob_poi + ops->ooboffs, len); | |
| return oob + len; | |
| case MTD_OOB_AUTO: { | |
| struct nand_oobfree *free = chip->ecc.layout->oobfree; | |
| uint32_t boffs = 0, roffs = ops->ooboffs; | |
| size_t bytes = 0; | |
| for(; free->length && len; free++, len -= bytes) { | |
| /* Read request not from offset 0 ? */ | |
| if (unlikely(roffs)) { | |
| if (roffs >= free->length) { | |
| roffs -= free->length; | |
| continue; | |
| } | |
| boffs = free->offset + roffs; | |
| bytes = min_t(size_t, len, | |
| (free->length - roffs)); | |
| roffs = 0; | |
| } else { | |
| bytes = min_t(size_t, len, free->length); | |
| boffs = free->offset; | |
| } | |
| memcpy(oob, chip->oob_poi + boffs, bytes); | |
| oob += bytes; | |
| } | |
| return oob; | |
| } | |
| default: | |
| BUG(); | |
| } | |
| return NULL; | |
| } | |
| /** | |
| * nand_do_read_ops - [Internal] Read data with ECC | |
| * | |
| * @mtd: MTD device structure | |
| * @from: offset to read from | |
| * @ops: oob ops structure | |
| * | |
| * Internal function. Called with chip held. | |
| */ | |
| static int nand_do_read_ops(struct mtd_info *mtd, loff_t from, | |
| struct mtd_oob_ops *ops) | |
| { | |
| int chipnr, page, realpage, col, bytes, aligned; | |
| struct nand_chip *chip = mtd->priv; | |
| struct mtd_ecc_stats stats; | |
| int blkcheck = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1; | |
| int sndcmd = 1; | |
| int ret = 0; | |
| uint32_t readlen = ops->len; | |
| uint8_t *bufpoi, *oob, *buf; | |
| stats = mtd->ecc_stats; | |
| chipnr = (int)(from >> chip->chip_shift); | |
| chip->select_chip(mtd, chipnr); | |
| realpage = (int)(from >> chip->page_shift); | |
| page = realpage & chip->pagemask; | |
| col = (int)(from & (mtd->writesize - 1)); | |
| chip->oob_poi = chip->buffers->oobrbuf; | |
| buf = ops->datbuf; | |
| oob = ops->oobbuf; | |
| while(1) { | |
| bytes = min(mtd->writesize - col, readlen); | |
| aligned = (bytes == mtd->writesize); | |
| /* Is the current page in the buffer ? */ | |
| if (realpage != chip->pagebuf || oob) { | |
| bufpoi = aligned ? buf : chip->buffers->databuf; | |
| if (likely(sndcmd)) { | |
| chip->cmdfunc(mtd, NAND_CMD_READ0, 0x00, page); | |
| sndcmd = 0; | |
| } | |
| /* Now read the page into the buffer */ | |
| if (unlikely(ops->mode == MTD_OOB_RAW)) | |
| ret = chip->ecc.read_page_raw(mtd, chip, bufpoi); | |
| else | |
| ret = chip->ecc.read_page(mtd, chip, bufpoi); | |
| if (ret < 0) | |
| break; | |
| /* Transfer not aligned data */ | |
| if (!aligned) { | |
| chip->pagebuf = realpage; | |
| memcpy(buf, chip->buffers->databuf + col, bytes); | |
| } | |
| buf += bytes; | |
| if (unlikely(oob)) { | |
| /* Raw mode does data:oob:data:oob */ | |
| if (ops->mode != MTD_OOB_RAW) | |
| oob = nand_transfer_oob(chip, oob, ops); | |
| else | |
| buf = nand_transfer_oob(chip, buf, ops); | |
| } | |
| if (!(chip->options & NAND_NO_READRDY)) { | |
| /* | |
| * Apply delay or wait for ready/busy pin. Do | |
| * this before the AUTOINCR check, so no | |
| * problems arise if a chip which does auto | |
| * increment is marked as NOAUTOINCR by the | |
| * board driver. | |
| */ | |
| if (!chip->dev_ready) | |
| udelay(chip->chip_delay); | |
| else | |
| nand_wait_ready(mtd); | |
| } | |
| } else { | |
| memcpy(buf, chip->buffers->databuf + col, bytes); | |
| buf += bytes; | |
| } | |
| readlen -= bytes; | |
| if (!readlen) | |
| break; | |
| /* For subsequent reads align to page boundary. */ | |
| col = 0; | |
| /* Increment page address */ | |
| realpage++; | |
| page = realpage & chip->pagemask; | |
| /* Check, if we cross a chip boundary */ | |
| if (!page) { | |
| chipnr++; | |
| chip->select_chip(mtd, -1); | |
| chip->select_chip(mtd, chipnr); | |
| } | |
| /* Check, if the chip supports auto page increment | |
| * or if we have hit a block boundary. | |
| */ | |
| if (!NAND_CANAUTOINCR(chip) || !(page & blkcheck)) | |
| sndcmd = 1; | |
| } | |
| ops->retlen = ops->len - (size_t) readlen; | |
| if (ret) | |
| return ret; | |
| if (mtd->ecc_stats.failed - stats.failed) | |
| return -EBADMSG; | |
| return mtd->ecc_stats.corrected - stats.corrected ? -EUCLEAN : 0; | |
| } | |
| /** | |
| * nand_read - [MTD Interface] MTD compability function for nand_do_read_ecc | |
| * @mtd: MTD device structure | |
| * @from: offset to read from | |
| * @len: number of bytes to read | |
| * @retlen: pointer to variable to store the number of read bytes | |
| * @buf: the databuffer to put data | |
| * | |
| * Get hold of the chip and call nand_do_read | |
| */ | |
| static int nand_read(struct mtd_info *mtd, loff_t from, size_t len, | |
| size_t *retlen, uint8_t *buf) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| int ret; | |
| /* Do not allow reads past end of device */ | |
| if ((from + len) > mtd->size) | |
| return -EINVAL; | |
| if (!len) | |
| return 0; | |
| nand_get_device(chip, mtd, FL_READING); | |
| chip->ops.len = len; | |
| chip->ops.datbuf = buf; | |
| chip->ops.oobbuf = NULL; | |
| ret = nand_do_read_ops(mtd, from, &chip->ops); | |
| *retlen = chip->ops.retlen; | |
| nand_release_device(mtd); | |
| return ret; | |
| } | |
| /** | |
| * nand_read_oob_std - [REPLACABLE] the most common OOB data read function | |
| * @mtd: mtd info structure | |
| * @chip: nand chip info structure | |
| * @page: page number to read | |
| * @sndcmd: flag whether to issue read command or not | |
| */ | |
| static int nand_read_oob_std(struct mtd_info *mtd, struct nand_chip *chip, | |
| int page, int sndcmd) | |
| { | |
| if (sndcmd) { | |
| chip->cmdfunc(mtd, NAND_CMD_READOOB, 0, page); | |
| sndcmd = 0; | |
| } | |
| chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); | |
| return sndcmd; | |
| } | |
| /** | |
| * nand_read_oob_syndrome - [REPLACABLE] OOB data read function for HW ECC | |
| * with syndromes | |
| * @mtd: mtd info structure | |
| * @chip: nand chip info structure | |
| * @page: page number to read | |
| * @sndcmd: flag whether to issue read command or not | |
| */ | |
| static int nand_read_oob_syndrome(struct mtd_info *mtd, struct nand_chip *chip, | |
| int page, int sndcmd) | |
| { | |
| uint8_t *buf = chip->oob_poi; | |
| int length = mtd->oobsize; | |
| int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad; | |
| int eccsize = chip->ecc.size; | |
| uint8_t *bufpoi = buf; | |
| int i, toread, sndrnd = 0, pos; | |
| chip->cmdfunc(mtd, NAND_CMD_READ0, chip->ecc.size, page); | |
| for (i = 0; i < chip->ecc.steps; i++) { | |
| if (sndrnd) { | |
| pos = eccsize + i * (eccsize + chunk); | |
| if (mtd->writesize > 512) | |
| chip->cmdfunc(mtd, NAND_CMD_RNDOUT, pos, -1); | |
| else | |
| chip->cmdfunc(mtd, NAND_CMD_READ0, pos, page); | |
| } else | |
| sndrnd = 1; | |
| toread = min_t(int, length, chunk); | |
| chip->read_buf(mtd, bufpoi, toread); | |
| bufpoi += toread; | |
| length -= toread; | |
| } | |
| if (length > 0) | |
| chip->read_buf(mtd, bufpoi, length); | |
| return 1; | |
| } | |
| /** | |
| * nand_write_oob_std - [REPLACABLE] the most common OOB data write function | |
| * @mtd: mtd info structure | |
| * @chip: nand chip info structure | |
| * @page: page number to write | |
| */ | |
| static int nand_write_oob_std(struct mtd_info *mtd, struct nand_chip *chip, | |
| int page) | |
| { | |
| int status = 0; | |
| const uint8_t *buf = chip->oob_poi; | |
| int length = mtd->oobsize; | |
| chip->cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, page); | |
| chip->write_buf(mtd, buf, length); | |
| /* Send command to program the OOB data */ | |
| chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); | |
| status = chip->waitfunc(mtd, chip); | |
| return status & NAND_STATUS_FAIL ? -EIO : 0; | |
| } | |
| /** | |
| * nand_write_oob_syndrome - [REPLACABLE] OOB data write function for HW ECC | |
| * with syndrome - only for large page flash ! | |
| * @mtd: mtd info structure | |
| * @chip: nand chip info structure | |
| * @page: page number to write | |
| */ | |
| static int nand_write_oob_syndrome(struct mtd_info *mtd, | |
| struct nand_chip *chip, int page) | |
| { | |
| int chunk = chip->ecc.bytes + chip->ecc.prepad + chip->ecc.postpad; | |
| int eccsize = chip->ecc.size, length = mtd->oobsize; | |
| int i, len, pos, status = 0, sndcmd = 0, steps = chip->ecc.steps; | |
| const uint8_t *bufpoi = chip->oob_poi; | |
| /* | |
| * data-ecc-data-ecc ... ecc-oob | |
| * or | |
| * data-pad-ecc-pad-data-pad .... ecc-pad-oob | |
| */ | |
| if (!chip->ecc.prepad && !chip->ecc.postpad) { | |
| pos = steps * (eccsize + chunk); | |
| steps = 0; | |
| } else | |
| pos = eccsize; | |
| chip->cmdfunc(mtd, NAND_CMD_SEQIN, pos, page); | |
| for (i = 0; i < steps; i++) { | |
| if (sndcmd) { | |
| if (mtd->writesize <= 512) { | |
| uint32_t fill = 0xFFFFFFFF; | |
| len = eccsize; | |
| while (len > 0) { | |
| int num = min_t(int, len, 4); | |
| chip->write_buf(mtd, (uint8_t *)&fill, | |
| num); | |
| len -= num; | |
| } | |
| } else { | |
| pos = eccsize + i * (eccsize + chunk); | |
| chip->cmdfunc(mtd, NAND_CMD_RNDIN, pos, -1); | |
| } | |
| } else | |
| sndcmd = 1; | |
| len = min_t(int, length, chunk); | |
| chip->write_buf(mtd, bufpoi, len); | |
| bufpoi += len; | |
| length -= len; | |
| } | |
| if (length > 0) | |
| chip->write_buf(mtd, bufpoi, length); | |
| chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); | |
| status = chip->waitfunc(mtd, chip); | |
| return status & NAND_STATUS_FAIL ? -EIO : 0; | |
| } | |
| /** | |
| * nand_do_read_oob - [Intern] NAND read out-of-band | |
| * @mtd: MTD device structure | |
| * @from: offset to read from | |
| * @ops: oob operations description structure | |
| * | |
| * NAND read out-of-band data from the spare area | |
| */ | |
| static int nand_do_read_oob(struct mtd_info *mtd, loff_t from, | |
| struct mtd_oob_ops *ops) | |
| { | |
| int page, realpage, chipnr, sndcmd = 1; | |
| struct nand_chip *chip = mtd->priv; | |
| int blkcheck = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1; | |
| int readlen = ops->len; | |
| uint8_t *buf = ops->oobbuf; | |
| DEBUG(MTD_DEBUG_LEVEL3, "nand_read_oob: from = 0x%08Lx, len = %i\n", | |
| (unsigned long long)from, readlen); | |
| chipnr = (int)(from >> chip->chip_shift); | |
| chip->select_chip(mtd, chipnr); | |
| /* Shift to get page */ | |
| realpage = (int)(from >> chip->page_shift); | |
| page = realpage & chip->pagemask; | |
| chip->oob_poi = chip->buffers->oobrbuf; | |
| while(1) { | |
| sndcmd = chip->ecc.read_oob(mtd, chip, page, sndcmd); | |
| buf = nand_transfer_oob(chip, buf, ops); | |
| if (!(chip->options & NAND_NO_READRDY)) { | |
| /* | |
| * Apply delay or wait for ready/busy pin. Do this | |
| * before the AUTOINCR check, so no problems arise if a | |
| * chip which does auto increment is marked as | |
| * NOAUTOINCR by the board driver. | |
| */ | |
| if (!chip->dev_ready) | |
| udelay(chip->chip_delay); | |
| else | |
| nand_wait_ready(mtd); | |
| } | |
| readlen -= ops->ooblen; | |
| if (!readlen) | |
| break; | |
| /* Increment page address */ | |
| realpage++; | |
| page = realpage & chip->pagemask; | |
| /* Check, if we cross a chip boundary */ | |
| if (!page) { | |
| chipnr++; | |
| chip->select_chip(mtd, -1); | |
| chip->select_chip(mtd, chipnr); | |
| } | |
| /* Check, if the chip supports auto page increment | |
| * or if we have hit a block boundary. | |
| */ | |
| if (!NAND_CANAUTOINCR(chip) || !(page & blkcheck)) | |
| sndcmd = 1; | |
| } | |
| ops->retlen = ops->len; | |
| return 0; | |
| } | |
| /** | |
| * nand_read_oob - [MTD Interface] NAND read data and/or out-of-band | |
| * @mtd: MTD device structure | |
| * @from: offset to read from | |
| * @ops: oob operation description structure | |
| * | |
| * NAND read data and/or out-of-band data | |
| */ | |
| static int nand_read_oob(struct mtd_info *mtd, loff_t from, | |
| struct mtd_oob_ops *ops) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| int ret = -ENOTSUPP; | |
| ops->retlen = 0; | |
| /* Do not allow reads past end of device */ | |
| if ((from + ops->len) > mtd->size) { | |
| DEBUG(MTD_DEBUG_LEVEL0, "nand_read_oob: " | |
| "Attempt read beyond end of device\n"); | |
| return -EINVAL; | |
| } | |
| nand_get_device(chip, mtd, FL_READING); | |
| switch(ops->mode) { | |
| case MTD_OOB_PLACE: | |
| case MTD_OOB_AUTO: | |
| case MTD_OOB_RAW: | |
| break; | |
| default: | |
| goto out; | |
| } | |
| if (!ops->datbuf) | |
| ret = nand_do_read_oob(mtd, from, ops); | |
| else | |
| ret = nand_do_read_ops(mtd, from, ops); | |
| out: | |
| nand_release_device(mtd); | |
| return ret; | |
| } | |
| /** | |
| * nand_write_page_raw - [Intern] raw page write function | |
| * @mtd: mtd info structure | |
| * @chip: nand chip info structure | |
| * @buf: data buffer | |
| */ | |
| static void nand_write_page_raw(struct mtd_info *mtd, struct nand_chip *chip, | |
| const uint8_t *buf) | |
| { | |
| chip->write_buf(mtd, buf, mtd->writesize); | |
| chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); | |
| } | |
| /** | |
| * nand_write_page_swecc - {REPLACABLE] software ecc based page write function | |
| * @mtd: mtd info structure | |
| * @chip: nand chip info structure | |
| * @buf: data buffer | |
| */ | |
| static void nand_write_page_swecc(struct mtd_info *mtd, struct nand_chip *chip, | |
| const uint8_t *buf) | |
| { | |
| int i, eccsize = chip->ecc.size; | |
| int eccbytes = chip->ecc.bytes; | |
| int eccsteps = chip->ecc.steps; | |
| uint8_t *ecc_calc = chip->buffers->ecccalc; | |
| const uint8_t *p = buf; | |
| int *eccpos = chip->ecc.layout->eccpos; | |
| /* Software ecc calculation */ | |
| for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) | |
| chip->ecc.calculate(mtd, p, &ecc_calc[i]); | |
| for (i = 0; i < chip->ecc.total; i++) | |
| chip->oob_poi[eccpos[i]] = ecc_calc[i]; | |
| nand_write_page_raw(mtd, chip, buf); | |
| } | |
| /** | |
| * nand_write_page_hwecc - {REPLACABLE] hardware ecc based page write function | |
| * @mtd: mtd info structure | |
| * @chip: nand chip info structure | |
| * @buf: data buffer | |
| */ | |
| static void nand_write_page_hwecc(struct mtd_info *mtd, struct nand_chip *chip, | |
| const uint8_t *buf) | |
| { | |
| int i, eccsize = chip->ecc.size; | |
| int eccbytes = chip->ecc.bytes; | |
| int eccsteps = chip->ecc.steps; | |
| uint8_t *ecc_calc = chip->buffers->ecccalc; | |
| const uint8_t *p = buf; | |
| int *eccpos = chip->ecc.layout->eccpos; | |
| for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { | |
| chip->ecc.hwctl(mtd, NAND_ECC_WRITE); | |
| chip->write_buf(mtd, p, eccsize); | |
| chip->ecc.calculate(mtd, p, &ecc_calc[i]); | |
| } | |
| for (i = 0; i < chip->ecc.total; i++) | |
| chip->oob_poi[eccpos[i]] = ecc_calc[i]; | |
| chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); | |
| } | |
| /** | |
| * nand_write_page_syndrome - {REPLACABLE] hardware ecc syndrom based page write | |
| * @mtd: mtd info structure | |
| * @chip: nand chip info structure | |
| * @buf: data buffer | |
| * | |
| * The hw generator calculates the error syndrome automatically. Therefor | |
| * we need a special oob layout and handling. | |
| */ | |
| static void nand_write_page_syndrome(struct mtd_info *mtd, | |
| struct nand_chip *chip, const uint8_t *buf) | |
| { | |
| int i, eccsize = chip->ecc.size; | |
| int eccbytes = chip->ecc.bytes; | |
| int eccsteps = chip->ecc.steps; | |
| const uint8_t *p = buf; | |
| uint8_t *oob = chip->oob_poi; | |
| for (i = 0; eccsteps; eccsteps--, i += eccbytes, p += eccsize) { | |
| chip->ecc.hwctl(mtd, NAND_ECC_WRITE); | |
| chip->write_buf(mtd, p, eccsize); | |
| if (chip->ecc.prepad) { | |
| chip->write_buf(mtd, oob, chip->ecc.prepad); | |
| oob += chip->ecc.prepad; | |
| } | |
| chip->ecc.calculate(mtd, p, oob); | |
| chip->write_buf(mtd, oob, eccbytes); | |
| oob += eccbytes; | |
| if (chip->ecc.postpad) { | |
| chip->write_buf(mtd, oob, chip->ecc.postpad); | |
| oob += chip->ecc.postpad; | |
| } | |
| } | |
| /* Calculate remaining oob bytes */ | |
| i = mtd->oobsize - (oob - chip->oob_poi); | |
| if (i) | |
| chip->write_buf(mtd, oob, i); | |
| } | |
| /** | |
| * nand_write_page - [REPLACEABLE] write one page | |
| * @mtd: MTD device structure | |
| * @chip: NAND chip descriptor | |
| * @buf: the data to write | |
| * @page: page number to write | |
| * @cached: cached programming | |
| * @raw: use _raw version of write_page | |
| */ | |
| static int nand_write_page(struct mtd_info *mtd, struct nand_chip *chip, | |
| const uint8_t *buf, int page, int cached, int raw) | |
| { | |
| int status; | |
| chip->cmdfunc(mtd, NAND_CMD_SEQIN, 0x00, page); | |
| if (unlikely(raw)) | |
| chip->ecc.write_page_raw(mtd, chip, buf); | |
| else | |
| chip->ecc.write_page(mtd, chip, buf); | |
| /* | |
| * Cached progamming disabled for now, Not sure if its worth the | |
| * trouble. The speed gain is not very impressive. (2.3->2.6Mib/s) | |
| */ | |
| cached = 0; | |
| if (!cached || !(chip->options & NAND_CACHEPRG)) { | |
| chip->cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1); | |
| status = chip->waitfunc(mtd, chip); | |
| /* | |
| * See if operation failed and additional status checks are | |
| * available | |
| */ | |
| if ((status & NAND_STATUS_FAIL) && (chip->errstat)) | |
| status = chip->errstat(mtd, chip, FL_WRITING, status, | |
| page); | |
| if (status & NAND_STATUS_FAIL) | |
| return -EIO; | |
| } else { | |
| chip->cmdfunc(mtd, NAND_CMD_CACHEDPROG, -1, -1); | |
| status = chip->waitfunc(mtd, chip); | |
| } | |
| #ifdef CONFIG_MTD_NAND_VERIFY_WRITE | |
| /* Send command to read back the data */ | |
| chip->cmdfunc(mtd, NAND_CMD_READ0, 0, page); | |
| if (chip->verify_buf(mtd, buf, mtd->writesize)) | |
| return -EIO; | |
| #endif | |
| return 0; | |
| } | |
| /** | |
| * nand_fill_oob - [Internal] Transfer client buffer to oob | |
| * @chip: nand chip structure | |
| * @oob: oob data buffer | |
| * @ops: oob ops structure | |
| */ | |
| static uint8_t *nand_fill_oob(struct nand_chip *chip, uint8_t *oob, | |
| struct mtd_oob_ops *ops) | |
| { | |
| size_t len = ops->ooblen; | |
| switch(ops->mode) { | |
| case MTD_OOB_PLACE: | |
| case MTD_OOB_RAW: | |
| memcpy(chip->oob_poi + ops->ooboffs, oob, len); | |
| return oob + len; | |
| case MTD_OOB_AUTO: { | |
| struct nand_oobfree *free = chip->ecc.layout->oobfree; | |
| uint32_t boffs = 0, woffs = ops->ooboffs; | |
| size_t bytes = 0; | |
| for(; free->length && len; free++, len -= bytes) { | |
| /* Write request not from offset 0 ? */ | |
| if (unlikely(woffs)) { | |
| if (woffs >= free->length) { | |
| woffs -= free->length; | |
| continue; | |
| } | |
| boffs = free->offset + woffs; | |
| bytes = min_t(size_t, len, | |
| (free->length - woffs)); | |
| woffs = 0; | |
| } else { | |
| bytes = min_t(size_t, len, free->length); | |
| boffs = free->offset; | |
| } | |
| memcpy(chip->oob_poi + boffs, oob, bytes); | |
| oob += bytes; | |
| } | |
| return oob; | |
| } | |
| default: | |
| BUG(); | |
| } | |
| return NULL; | |
| } | |
| #define NOTALIGNED(x) (x & (mtd->writesize-1)) != 0 | |
| /** | |
| * nand_do_write_ops - [Internal] NAND write with ECC | |
| * @mtd: MTD device structure | |
| * @to: offset to write to | |
| * @ops: oob operations description structure | |
| * | |
| * NAND write with ECC | |
| */ | |
| static int nand_do_write_ops(struct mtd_info *mtd, loff_t to, | |
| struct mtd_oob_ops *ops) | |
| { | |
| int chipnr, realpage, page, blockmask; | |
| struct nand_chip *chip = mtd->priv; | |
| uint32_t writelen = ops->len; | |
| uint8_t *oob = ops->oobbuf; | |
| uint8_t *buf = ops->datbuf; | |
| int bytes = mtd->writesize; | |
| int ret; | |
| ops->retlen = 0; | |
| /* reject writes, which are not page aligned */ | |
| if (NOTALIGNED(to) || NOTALIGNED(ops->len)) { | |
| printk(KERN_NOTICE "nand_write: " | |
| "Attempt to write not page aligned data\n"); | |
| return -EINVAL; | |
| } | |
| if (!writelen) | |
| return 0; | |
| chipnr = (int)(to >> chip->chip_shift); | |
| chip->select_chip(mtd, chipnr); | |
| /* Check, if it is write protected */ | |
| if (nand_check_wp(mtd)) | |
| return -EIO; | |
| realpage = (int)(to >> chip->page_shift); | |
| page = realpage & chip->pagemask; | |
| blockmask = (1 << (chip->phys_erase_shift - chip->page_shift)) - 1; | |
| /* Invalidate the page cache, when we write to the cached page */ | |
| if (to <= (chip->pagebuf << chip->page_shift) && | |
| (chip->pagebuf << chip->page_shift) < (to + ops->len)) | |
| chip->pagebuf = -1; | |
| chip->oob_poi = chip->buffers->oobwbuf; | |
| while(1) { | |
| int cached = writelen > bytes && page != blockmask; | |
| if (unlikely(oob)) | |
| oob = nand_fill_oob(chip, oob, ops); | |
| ret = chip->write_page(mtd, chip, buf, page, cached, | |
| (ops->mode == MTD_OOB_RAW)); | |
| if (ret) | |
| break; | |
| writelen -= bytes; | |
| if (!writelen) | |
| break; | |
| buf += bytes; | |
| realpage++; | |
| page = realpage & chip->pagemask; | |
| /* Check, if we cross a chip boundary */ | |
| if (!page) { | |
| chipnr++; | |
| chip->select_chip(mtd, -1); | |
| chip->select_chip(mtd, chipnr); | |
| } | |
| } | |
| if (unlikely(oob)) | |
| memset(chip->oob_poi, 0xff, mtd->oobsize); | |
| ops->retlen = ops->len - writelen; | |
| return ret; | |
| } | |
| /** | |
| * nand_write - [MTD Interface] NAND write with ECC | |
| * @mtd: MTD device structure | |
| * @to: offset to write to | |
| * @len: number of bytes to write | |
| * @retlen: pointer to variable to store the number of written bytes | |
| * @buf: the data to write | |
| * | |
| * NAND write with ECC | |
| */ | |
| static int nand_write(struct mtd_info *mtd, loff_t to, size_t len, | |
| size_t *retlen, const uint8_t *buf) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| int ret; | |
| /* Do not allow reads past end of device */ | |
| if ((to + len) > mtd->size) | |
| return -EINVAL; | |
| if (!len) | |
| return 0; | |
| nand_get_device(chip, mtd, FL_WRITING); | |
| chip->ops.len = len; | |
| chip->ops.datbuf = (uint8_t *)buf; | |
| chip->ops.oobbuf = NULL; | |
| ret = nand_do_write_ops(mtd, to, &chip->ops); | |
| *retlen = chip->ops.retlen; | |
| nand_release_device(mtd); | |
| return ret; | |
| } | |
| /** | |
| * nand_do_write_oob - [MTD Interface] NAND write out-of-band | |
| * @mtd: MTD device structure | |
| * @to: offset to write to | |
| * @ops: oob operation description structure | |
| * | |
| * NAND write out-of-band | |
| */ | |
| static int nand_do_write_oob(struct mtd_info *mtd, loff_t to, | |
| struct mtd_oob_ops *ops) | |
| { | |
| int chipnr, page, status; | |
| struct nand_chip *chip = mtd->priv; | |
| DEBUG(MTD_DEBUG_LEVEL3, "nand_write_oob: to = 0x%08x, len = %i\n", | |
| (unsigned int)to, (int)ops->len); | |
| /* Do not allow write past end of page */ | |
| if ((ops->ooboffs + ops->len) > mtd->oobsize) { | |
| DEBUG(MTD_DEBUG_LEVEL0, "nand_write_oob: " | |
| "Attempt to write past end of page\n"); | |
| return -EINVAL; | |
| } | |
| chipnr = (int)(to >> chip->chip_shift); | |
| chip->select_chip(mtd, chipnr); | |
| /* Shift to get page */ | |
| page = (int)(to >> chip->page_shift); | |
| /* | |
| * Reset the chip. Some chips (like the Toshiba TC5832DC found in one | |
| * of my DiskOnChip 2000 test units) will clear the whole data page too | |
| * if we don't do this. I have no clue why, but I seem to have 'fixed' | |
| * it in the doc2000 driver in August 1999. dwmw2. | |
| */ | |
| chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1); | |
| /* Check, if it is write protected */ | |
| if (nand_check_wp(mtd)) | |
| return -EROFS; | |
| /* Invalidate the page cache, if we write to the cached page */ | |
| if (page == chip->pagebuf) | |
| chip->pagebuf = -1; | |
| chip->oob_poi = chip->buffers->oobwbuf; | |
| memset(chip->oob_poi, 0xff, mtd->oobsize); | |
| nand_fill_oob(chip, ops->oobbuf, ops); | |
| status = chip->ecc.write_oob(mtd, chip, page & chip->pagemask); | |
| memset(chip->oob_poi, 0xff, mtd->oobsize); | |
| if (status) | |
| return status; | |
| ops->retlen = ops->len; | |
| return 0; | |
| } | |
| /** | |
| * nand_write_oob - [MTD Interface] NAND write data and/or out-of-band | |
| * @mtd: MTD device structure | |
| * @to: offset to write to | |
| * @ops: oob operation description structure | |
| */ | |
| static int nand_write_oob(struct mtd_info *mtd, loff_t to, | |
| struct mtd_oob_ops *ops) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| int ret = -ENOTSUPP; | |
| ops->retlen = 0; | |
| /* Do not allow writes past end of device */ | |
| if ((to + ops->len) > mtd->size) { | |
| DEBUG(MTD_DEBUG_LEVEL0, "nand_read_oob: " | |
| "Attempt read beyond end of device\n"); | |
| return -EINVAL; | |
| } | |
| nand_get_device(chip, mtd, FL_WRITING); | |
| switch(ops->mode) { | |
| case MTD_OOB_PLACE: | |
| case MTD_OOB_AUTO: | |
| case MTD_OOB_RAW: | |
| break; | |
| default: | |
| goto out; | |
| } | |
| if (!ops->datbuf) | |
| ret = nand_do_write_oob(mtd, to, ops); | |
| else | |
| ret = nand_do_write_ops(mtd, to, ops); | |
| out: | |
| nand_release_device(mtd); | |
| return ret; | |
| } | |
| /** | |
| * single_erease_cmd - [GENERIC] NAND standard block erase command function | |
| * @mtd: MTD device structure | |
| * @page: the page address of the block which will be erased | |
| * | |
| * Standard erase command for NAND chips | |
| */ | |
| static void single_erase_cmd(struct mtd_info *mtd, int page) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| /* Send commands to erase a block */ | |
| chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); | |
| chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); | |
| } | |
| /** | |
| * multi_erease_cmd - [GENERIC] AND specific block erase command function | |
| * @mtd: MTD device structure | |
| * @page: the page address of the block which will be erased | |
| * | |
| * AND multi block erase command function | |
| * Erase 4 consecutive blocks | |
| */ | |
| static void multi_erase_cmd(struct mtd_info *mtd, int page) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| /* Send commands to erase a block */ | |
| chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++); | |
| chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++); | |
| chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page++); | |
| chip->cmdfunc(mtd, NAND_CMD_ERASE1, -1, page); | |
| chip->cmdfunc(mtd, NAND_CMD_ERASE2, -1, -1); | |
| } | |
| /** | |
| * nand_erase - [MTD Interface] erase block(s) | |
| * @mtd: MTD device structure | |
| * @instr: erase instruction | |
| * | |
| * Erase one ore more blocks | |
| */ | |
| static int nand_erase(struct mtd_info *mtd, struct erase_info *instr) | |
| { | |
| return nand_erase_nand(mtd, instr, 0); | |
| } | |
| #define BBT_PAGE_MASK 0xffffff3f | |
| /** | |
| * nand_erase_nand - [Internal] erase block(s) | |
| * @mtd: MTD device structure | |
| * @instr: erase instruction | |
| * @allowbbt: allow erasing the bbt area | |
| * | |
| * Erase one ore more blocks | |
| */ | |
| int nand_erase_nand(struct mtd_info *mtd, struct erase_info *instr, | |
| int allowbbt) | |
| { | |
| int page, len, status, pages_per_block, ret, chipnr; | |
| struct nand_chip *chip = mtd->priv; | |
| int rewrite_bbt[NAND_MAX_CHIPS]={0}; | |
| unsigned int bbt_masked_page = 0xffffffff; | |
| DEBUG(MTD_DEBUG_LEVEL3, "nand_erase: start = 0x%08x, len = %i\n", | |
| (unsigned int)instr->addr, (unsigned int)instr->len); | |
| /* Start address must align on block boundary */ | |
| if (instr->addr & ((1 << chip->phys_erase_shift) - 1)) { | |
| DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: Unaligned address\n"); | |
| return -EINVAL; | |
| } | |
| /* Length must align on block boundary */ | |
| if (instr->len & ((1 << chip->phys_erase_shift) - 1)) { | |
| DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: " | |
| "Length not block aligned\n"); | |
| return -EINVAL; | |
| } | |
| /* Do not allow erase past end of device */ | |
| if ((instr->len + instr->addr) > mtd->size) { | |
| DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: " | |
| "Erase past end of device\n"); | |
| return -EINVAL; | |
| } | |
| instr->fail_addr = 0xffffffff; | |
| /* Grab the lock and see if the device is available */ | |
| nand_get_device(chip, mtd, FL_ERASING); | |
| /* Shift to get first page */ | |
| page = (int)(instr->addr >> chip->page_shift); | |
| chipnr = (int)(instr->addr >> chip->chip_shift); | |
| /* Calculate pages in each block */ | |
| pages_per_block = 1 << (chip->phys_erase_shift - chip->page_shift); | |
| /* Select the NAND device */ | |
| chip->select_chip(mtd, chipnr); | |
| /* Check, if it is write protected */ | |
| if (nand_check_wp(mtd)) { | |
| DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: " | |
| "Device is write protected!!!\n"); | |
| instr->state = MTD_ERASE_FAILED; | |
| goto erase_exit; | |
| } | |
| /* | |
| * If BBT requires refresh, set the BBT page mask to see if the BBT | |
| * should be rewritten. Otherwise the mask is set to 0xffffffff which | |
| * can not be matched. This is also done when the bbt is actually | |
| * erased to avoid recusrsive updates | |
| */ | |
| if (chip->options & BBT_AUTO_REFRESH && !allowbbt) | |
| bbt_masked_page = chip->bbt_td->pages[chipnr] & BBT_PAGE_MASK; | |
| /* Loop through the pages */ | |
| len = instr->len; | |
| instr->state = MTD_ERASING; | |
| while (len) { | |
| /* | |
| * heck if we have a bad block, we do not erase bad blocks ! | |
| */ | |
| if (nand_block_checkbad(mtd, ((loff_t) page) << | |
| chip->page_shift, 0, allowbbt)) { | |
| printk(KERN_WARNING "nand_erase: attempt to erase a " | |
| "bad block at page 0x%08x\n", page); | |
| instr->state = MTD_ERASE_FAILED; | |
| goto erase_exit; | |
| } | |
| /* | |
| * Invalidate the page cache, if we erase the block which | |
| * contains the current cached page | |
| */ | |
| if (page <= chip->pagebuf && chip->pagebuf < | |
| (page + pages_per_block)) | |
| chip->pagebuf = -1; | |
| chip->erase_cmd(mtd, page & chip->pagemask); | |
| status = chip->waitfunc(mtd, chip); | |
| /* | |
| * See if operation failed and additional status checks are | |
| * available | |
| */ | |
| if ((status & NAND_STATUS_FAIL) && (chip->errstat)) | |
| status = chip->errstat(mtd, chip, FL_ERASING, | |
| status, page); | |
| /* See if block erase succeeded */ | |
| if (status & NAND_STATUS_FAIL) { | |
| DEBUG(MTD_DEBUG_LEVEL0, "nand_erase: " | |
| "Failed erase, page 0x%08x\n", page); | |
| instr->state = MTD_ERASE_FAILED; | |
| instr->fail_addr = (page << chip->page_shift); | |
| goto erase_exit; | |
| } | |
| /* | |
| * If BBT requires refresh, set the BBT rewrite flag to the | |
| * page being erased | |
| */ | |
| if (bbt_masked_page != 0xffffffff && | |
| (page & BBT_PAGE_MASK) == bbt_masked_page) | |
| rewrite_bbt[chipnr] = (page << chip->page_shift); | |
| /* Increment page address and decrement length */ | |
| len -= (1 << chip->phys_erase_shift); | |
| page += pages_per_block; | |
| /* Check, if we cross a chip boundary */ | |
| if (len && !(page & chip->pagemask)) { | |
| chipnr++; | |
| chip->select_chip(mtd, -1); | |
| chip->select_chip(mtd, chipnr); | |
| /* | |
| * If BBT requires refresh and BBT-PERCHIP, set the BBT | |
| * page mask to see if this BBT should be rewritten | |
| */ | |
| if (bbt_masked_page != 0xffffffff && | |
| (chip->bbt_td->options & NAND_BBT_PERCHIP)) | |
| bbt_masked_page = chip->bbt_td->pages[chipnr] & | |
| BBT_PAGE_MASK; | |
| } | |
| } | |
| instr->state = MTD_ERASE_DONE; | |
| erase_exit: | |
| ret = instr->state == MTD_ERASE_DONE ? 0 : -EIO; | |
| /* Do call back function */ | |
| if (!ret) | |
| mtd_erase_callback(instr); | |
| /* Deselect and wake up anyone waiting on the device */ | |
| nand_release_device(mtd); | |
| /* | |
| * If BBT requires refresh and erase was successful, rewrite any | |
| * selected bad block tables | |
| */ | |
| if (bbt_masked_page == 0xffffffff || ret) | |
| return ret; | |
| for (chipnr = 0; chipnr < chip->numchips; chipnr++) { | |
| if (!rewrite_bbt[chipnr]) | |
| continue; | |
| /* update the BBT for chip */ | |
| DEBUG(MTD_DEBUG_LEVEL0, "nand_erase_nand: nand_update_bbt " | |
| "(%d:0x%0x 0x%0x)\n", chipnr, rewrite_bbt[chipnr], | |
| chip->bbt_td->pages[chipnr]); | |
| nand_update_bbt(mtd, rewrite_bbt[chipnr]); | |
| } | |
| /* Return more or less happy */ | |
| return ret; | |
| } | |
| /** | |
| * nand_sync - [MTD Interface] sync | |
| * @mtd: MTD device structure | |
| * | |
| * Sync is actually a wait for chip ready function | |
| */ | |
| static void nand_sync(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| DEBUG(MTD_DEBUG_LEVEL3, "nand_sync: called\n"); | |
| /* Grab the lock and see if the device is available */ | |
| nand_get_device(chip, mtd, FL_SYNCING); | |
| /* Release it and go back */ | |
| nand_release_device(mtd); | |
| } | |
| /** | |
| * nand_block_isbad - [MTD Interface] Check if block at offset is bad | |
| * @mtd: MTD device structure | |
| * @offs: offset relative to mtd start | |
| */ | |
| static int nand_block_isbad(struct mtd_info *mtd, loff_t offs) | |
| { | |
| /* Check for invalid offset */ | |
| if (offs > mtd->size) | |
| return -EINVAL; | |
| return nand_block_checkbad(mtd, offs, 1, 0); | |
| } | |
| /** | |
| * nand_block_markbad - [MTD Interface] Mark block at the given offset as bad | |
| * @mtd: MTD device structure | |
| * @ofs: offset relative to mtd start | |
| */ | |
| static int nand_block_markbad(struct mtd_info *mtd, loff_t ofs) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| int ret; | |
| if ((ret = nand_block_isbad(mtd, ofs))) { | |
| /* If it was bad already, return success and do nothing. */ | |
| if (ret > 0) | |
| return 0; | |
| return ret; | |
| } | |
| return chip->block_markbad(mtd, ofs); | |
| } | |
| /** | |
| * nand_suspend - [MTD Interface] Suspend the NAND flash | |
| * @mtd: MTD device structure | |
| */ | |
| static int nand_suspend(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| return nand_get_device(chip, mtd, FL_PM_SUSPENDED); | |
| } | |
| /** | |
| * nand_resume - [MTD Interface] Resume the NAND flash | |
| * @mtd: MTD device structure | |
| */ | |
| static void nand_resume(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| if (chip->state == FL_PM_SUSPENDED) | |
| nand_release_device(mtd); | |
| else | |
| printk(KERN_ERR "nand_resume() called for a chip which is not " | |
| "in suspended state\n"); | |
| } | |
| /* | |
| * Set default functions | |
| */ | |
| static void nand_set_defaults(struct nand_chip *chip, int busw) | |
| { | |
| /* check for proper chip_delay setup, set 20us if not */ | |
| if (!chip->chip_delay) | |
| chip->chip_delay = 20; | |
| /* check, if a user supplied command function given */ | |
| if (chip->cmdfunc == NULL) | |
| chip->cmdfunc = nand_command; | |
| /* check, if a user supplied wait function given */ | |
| if (chip->waitfunc == NULL) | |
| chip->waitfunc = nand_wait; | |
| if (!chip->select_chip) | |
| chip->select_chip = nand_select_chip; | |
| if (!chip->read_byte) | |
| chip->read_byte = busw ? nand_read_byte16 : nand_read_byte; | |
| if (!chip->read_word) | |
| chip->read_word = nand_read_word; | |
| if (!chip->block_bad) | |
| chip->block_bad = nand_block_bad; | |
| if (!chip->block_markbad) | |
| chip->block_markbad = nand_default_block_markbad; | |
| if (!chip->write_buf) | |
| chip->write_buf = busw ? nand_write_buf16 : nand_write_buf; | |
| if (!chip->read_buf) | |
| chip->read_buf = busw ? nand_read_buf16 : nand_read_buf; | |
| if (!chip->verify_buf) | |
| chip->verify_buf = busw ? nand_verify_buf16 : nand_verify_buf; | |
| if (!chip->scan_bbt) | |
| chip->scan_bbt = nand_default_bbt; | |
| if (!chip->controller) { | |
| chip->controller = &chip->hwcontrol; | |
| spin_lock_init(&chip->controller->lock); | |
| init_waitqueue_head(&chip->controller->wq); | |
| } | |
| } | |
| /* | |
| * Get the flash and manufacturer id and lookup if the type is supported | |
| */ | |
| static struct nand_flash_dev *nand_get_flash_type(struct mtd_info *mtd, | |
| struct nand_chip *chip, | |
| int busw, int *maf_id) | |
| { | |
| struct nand_flash_dev *type = NULL; | |
| int i, dev_id, maf_idx; | |
| /* Select the device */ | |
| chip->select_chip(mtd, 0); | |
| /* Send the command for reading device ID */ | |
| chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); | |
| /* Read manufacturer and device IDs */ | |
| *maf_id = chip->read_byte(mtd); | |
| dev_id = chip->read_byte(mtd); | |
| /* Lookup the flash id */ | |
| for (i = 0; nand_flash_ids[i].name != NULL; i++) { | |
| if (dev_id == nand_flash_ids[i].id) { | |
| type = &nand_flash_ids[i]; | |
| break; | |
| } | |
| } | |
| if (!type) | |
| return ERR_PTR(-ENODEV); | |
| if (!mtd->name) | |
| mtd->name = type->name; | |
| chip->chipsize = type->chipsize << 20; | |
| /* Newer devices have all the information in additional id bytes */ | |
| if (!type->pagesize) { | |
| int extid; | |
| /* The 3rd id byte contains non relevant data ATM */ | |
| extid = chip->read_byte(mtd); | |
| /* The 4th id byte is the important one */ | |
| extid = chip->read_byte(mtd); | |
| /* Calc pagesize */ | |
| mtd->writesize = 1024 << (extid & 0x3); | |
| extid >>= 2; | |
| /* Calc oobsize */ | |
| mtd->oobsize = (8 << (extid & 0x01)) * (mtd->writesize >> 9); | |
| extid >>= 2; | |
| /* Calc blocksize. Blocksize is multiples of 64KiB */ | |
| mtd->erasesize = (64 * 1024) << (extid & 0x03); | |
| extid >>= 2; | |
| /* Get buswidth information */ | |
| busw = (extid & 0x01) ? NAND_BUSWIDTH_16 : 0; | |
| } else { | |
| /* | |
| * Old devices have chip data hardcoded in the device id table | |
| */ | |
| mtd->erasesize = type->erasesize; | |
| mtd->writesize = type->pagesize; | |
| mtd->oobsize = mtd->writesize / 32; | |
| busw = type->options & NAND_BUSWIDTH_16; | |
| } | |
| /* Try to identify manufacturer */ | |
| for (maf_idx = 0; nand_manuf_ids[maf_idx].id != 0x0; maf_idx++) { | |
| if (nand_manuf_ids[maf_idx].id == *maf_id) | |
| break; | |
| } | |
| /* | |
| * Check, if buswidth is correct. Hardware drivers should set | |
| * chip correct ! | |
| */ | |
| if (busw != (chip->options & NAND_BUSWIDTH_16)) { | |
| printk(KERN_INFO "NAND device: Manufacturer ID:" | |
| " 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id, | |
| dev_id, nand_manuf_ids[maf_idx].name, mtd->name); | |
| printk(KERN_WARNING "NAND bus width %d instead %d bit\n", | |
| (chip->options & NAND_BUSWIDTH_16) ? 16 : 8, | |
| busw ? 16 : 8); | |
| return ERR_PTR(-EINVAL); | |
| } | |
| /* Calculate the address shift from the page size */ | |
| chip->page_shift = ffs(mtd->writesize) - 1; | |
| /* Convert chipsize to number of pages per chip -1. */ | |
| chip->pagemask = (chip->chipsize >> chip->page_shift) - 1; | |
| chip->bbt_erase_shift = chip->phys_erase_shift = | |
| ffs(mtd->erasesize) - 1; | |
| chip->chip_shift = ffs(chip->chipsize) - 1; | |
| /* Set the bad block position */ | |
| chip->badblockpos = mtd->writesize > 512 ? | |
| NAND_LARGE_BADBLOCK_POS : NAND_SMALL_BADBLOCK_POS; | |
| /* Get chip options, preserve non chip based options */ | |
| chip->options &= ~NAND_CHIPOPTIONS_MSK; | |
| chip->options |= type->options & NAND_CHIPOPTIONS_MSK; | |
| /* | |
| * Set chip as a default. Board drivers can override it, if necessary | |
| */ | |
| chip->options |= NAND_NO_AUTOINCR; | |
| /* Check if chip is a not a samsung device. Do not clear the | |
| * options for chips which are not having an extended id. | |
| */ | |
| if (*maf_id != NAND_MFR_SAMSUNG && !type->pagesize) | |
| chip->options &= ~NAND_SAMSUNG_LP_OPTIONS; | |
| /* Check for AND chips with 4 page planes */ | |
| if (chip->options & NAND_4PAGE_ARRAY) | |
| chip->erase_cmd = multi_erase_cmd; | |
| else | |
| chip->erase_cmd = single_erase_cmd; | |
| /* Do not replace user supplied command function ! */ | |
| if (mtd->writesize > 512 && chip->cmdfunc == nand_command) | |
| chip->cmdfunc = nand_command_lp; | |
| printk(KERN_INFO "NAND device: Manufacturer ID:" | |
| " 0x%02x, Chip ID: 0x%02x (%s %s)\n", *maf_id, dev_id, | |
| nand_manuf_ids[maf_idx].name, type->name); | |
| return type; | |
| } | |
| /** | |
| * nand_scan_ident - [NAND Interface] Scan for the NAND device | |
| * @mtd: MTD device structure | |
| * @maxchips: Number of chips to scan for | |
| * | |
| * This is the first phase of the normal nand_scan() function. It | |
| * reads the flash ID and sets up MTD fields accordingly. | |
| * | |
| * The mtd->owner field must be set to the module of the caller. | |
| */ | |
| int nand_scan_ident(struct mtd_info *mtd, int maxchips) | |
| { | |
| int i, busw, nand_maf_id; | |
| struct nand_chip *chip = mtd->priv; | |
| struct nand_flash_dev *type; | |
| /* Get buswidth to select the correct functions */ | |
| busw = chip->options & NAND_BUSWIDTH_16; | |
| /* Set the default functions */ | |
| nand_set_defaults(chip, busw); | |
| /* Read the flash type */ | |
| type = nand_get_flash_type(mtd, chip, busw, &nand_maf_id); | |
| if (IS_ERR(type)) { | |
| printk(KERN_WARNING "No NAND device found!!!\n"); | |
| chip->select_chip(mtd, -1); | |
| return PTR_ERR(type); | |
| } | |
| /* Check for a chip array */ | |
| for (i = 1; i < maxchips; i++) { | |
| chip->select_chip(mtd, i); | |
| /* Send the command for reading device ID */ | |
| chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1); | |
| /* Read manufacturer and device IDs */ | |
| if (nand_maf_id != chip->read_byte(mtd) || | |
| type->id != chip->read_byte(mtd)) | |
| break; | |
| } | |
| if (i > 1) | |
| printk(KERN_INFO "%d NAND chips detected\n", i); | |
| /* Store the number of chips and calc total size for mtd */ | |
| chip->numchips = i; | |
| mtd->size = i * chip->chipsize; | |
| return 0; | |
| } | |
| /** | |
| * nand_scan_tail - [NAND Interface] Scan for the NAND device | |
| * @mtd: MTD device structure | |
| * @maxchips: Number of chips to scan for | |
| * | |
| * This is the second phase of the normal nand_scan() function. It | |
| * fills out all the uninitialized function pointers with the defaults | |
| * and scans for a bad block table if appropriate. | |
| */ | |
| int nand_scan_tail(struct mtd_info *mtd) | |
| { | |
| int i; | |
| struct nand_chip *chip = mtd->priv; | |
| if (!(chip->options & NAND_OWN_BUFFERS)) | |
| chip->buffers = kmalloc(sizeof(*chip->buffers), GFP_KERNEL); | |
| if (!chip->buffers) | |
| return -ENOMEM; | |
| /* Preset the internal oob write buffer */ | |
| memset(chip->buffers->oobwbuf, 0xff, mtd->oobsize); | |
| /* | |
| * If no default placement scheme is given, select an appropriate one | |
| */ | |
| if (!chip->ecc.layout) { | |
| switch (mtd->oobsize) { | |
| case 8: | |
| chip->ecc.layout = &nand_oob_8; | |
| break; | |
| case 16: | |
| chip->ecc.layout = &nand_oob_16; | |
| break; | |
| case 64: | |
| chip->ecc.layout = &nand_oob_64; | |
| break; | |
| default: | |
| printk(KERN_WARNING "No oob scheme defined for " | |
| "oobsize %d\n", mtd->oobsize); | |
| BUG(); | |
| } | |
| } | |
| if (!chip->write_page) | |
| chip->write_page = nand_write_page; | |
| /* | |
| * check ECC mode, default to software if 3byte/512byte hardware ECC is | |
| * selected and we have 256 byte pagesize fallback to software ECC | |
| */ | |
| if (!chip->ecc.read_page_raw) | |
| chip->ecc.read_page_raw = nand_read_page_raw; | |
| if (!chip->ecc.write_page_raw) | |
| chip->ecc.write_page_raw = nand_write_page_raw; | |
| switch (chip->ecc.mode) { | |
| case NAND_ECC_HW: | |
| /* Use standard hwecc read page function ? */ | |
| if (!chip->ecc.read_page) | |
| chip->ecc.read_page = nand_read_page_hwecc; | |
| if (!chip->ecc.write_page) | |
| chip->ecc.write_page = nand_write_page_hwecc; | |
| if (!chip->ecc.read_oob) | |
| chip->ecc.read_oob = nand_read_oob_std; | |
| if (!chip->ecc.write_oob) | |
| chip->ecc.write_oob = nand_write_oob_std; | |
| case NAND_ECC_HW_SYNDROME: | |
| if (!chip->ecc.calculate || !chip->ecc.correct || | |
| !chip->ecc.hwctl) { | |
| printk(KERN_WARNING "No ECC functions supplied, " | |
| "Hardware ECC not possible\n"); | |
| BUG(); | |
| } | |
| /* Use standard syndrome read/write page function ? */ | |
| if (!chip->ecc.read_page) | |
| chip->ecc.read_page = nand_read_page_syndrome; | |
| if (!chip->ecc.write_page) | |
| chip->ecc.write_page = nand_write_page_syndrome; | |
| if (!chip->ecc.read_oob) | |
| chip->ecc.read_oob = nand_read_oob_syndrome; | |
| if (!chip->ecc.write_oob) | |
| chip->ecc.write_oob = nand_write_oob_syndrome; | |
| if (mtd->writesize >= chip->ecc.size) | |
| break; | |
| printk(KERN_WARNING "%d byte HW ECC not possible on " | |
| "%d byte page size, fallback to SW ECC\n", | |
| chip->ecc.size, mtd->writesize); | |
| chip->ecc.mode = NAND_ECC_SOFT; | |
| case NAND_ECC_SOFT: | |
| chip->ecc.calculate = nand_calculate_ecc; | |
| chip->ecc.correct = nand_correct_data; | |
| chip->ecc.read_page = nand_read_page_swecc; | |
| chip->ecc.write_page = nand_write_page_swecc; | |
| chip->ecc.read_oob = nand_read_oob_std; | |
| chip->ecc.write_oob = nand_write_oob_std; | |
| chip->ecc.size = 256; | |
| chip->ecc.bytes = 3; | |
| break; | |
| case NAND_ECC_NONE: | |
| printk(KERN_WARNING "NAND_ECC_NONE selected by board driver. " | |
| "This is not recommended !!\n"); | |
| chip->ecc.read_page = nand_read_page_raw; | |
| chip->ecc.write_page = nand_write_page_raw; | |
| chip->ecc.read_oob = nand_read_oob_std; | |
| chip->ecc.write_oob = nand_write_oob_std; | |
| chip->ecc.size = mtd->writesize; | |
| chip->ecc.bytes = 0; | |
| break; | |
| default: | |
| printk(KERN_WARNING "Invalid NAND_ECC_MODE %d\n", | |
| chip->ecc.mode); | |
| BUG(); | |
| } | |
| /* | |
| * The number of bytes available for a client to place data into | |
| * the out of band area | |
| */ | |
| chip->ecc.layout->oobavail = 0; | |
| for (i = 0; chip->ecc.layout->oobfree[i].length; i++) | |
| chip->ecc.layout->oobavail += | |
| chip->ecc.layout->oobfree[i].length; | |
| /* | |
| * Set the number of read / write steps for one page depending on ECC | |
| * mode | |
| */ | |
| chip->ecc.steps = mtd->writesize / chip->ecc.size; | |
| if(chip->ecc.steps * chip->ecc.size != mtd->writesize) { | |
| printk(KERN_WARNING "Invalid ecc parameters\n"); | |
| BUG(); | |
| } | |
| chip->ecc.total = chip->ecc.steps * chip->ecc.bytes; | |
| /* Initialize state */ | |
| chip->state = FL_READY; | |
| /* De-select the device */ | |
| chip->select_chip(mtd, -1); | |
| /* Invalidate the pagebuffer reference */ | |
| chip->pagebuf = -1; | |
| /* Fill in remaining MTD driver data */ | |
| mtd->type = MTD_NANDFLASH; | |
| mtd->flags = MTD_CAP_NANDFLASH; | |
| mtd->ecctype = MTD_ECC_SW; | |
| mtd->erase = nand_erase; | |
| mtd->point = NULL; | |
| mtd->unpoint = NULL; | |
| mtd->read = nand_read; | |
| mtd->write = nand_write; | |
| mtd->read_oob = nand_read_oob; | |
| mtd->write_oob = nand_write_oob; | |
| mtd->sync = nand_sync; | |
| mtd->lock = NULL; | |
| mtd->unlock = NULL; | |
| mtd->suspend = nand_suspend; | |
| mtd->resume = nand_resume; | |
| mtd->block_isbad = nand_block_isbad; | |
| mtd->block_markbad = nand_block_markbad; | |
| /* propagate ecc.layout to mtd_info */ | |
| mtd->ecclayout = chip->ecc.layout; | |
| /* Check, if we should skip the bad block table scan */ | |
| if (chip->options & NAND_SKIP_BBTSCAN) | |
| return 0; | |
| /* Build bad block table */ | |
| return chip->scan_bbt(mtd); | |
| } | |
| /* module_text_address() isn't exported, and it's mostly a pointless | |
| test if this is a module _anyway_ -- they'd have to try _really_ hard | |
| to call us from in-kernel code if the core NAND support is modular. */ | |
| #ifdef MODULE | |
| #define caller_is_module() (1) | |
| #else | |
| #define caller_is_module() \ | |
| module_text_address((unsigned long)__builtin_return_address(0)) | |
| #endif | |
| /** | |
| * nand_scan - [NAND Interface] Scan for the NAND device | |
| * @mtd: MTD device structure | |
| * @maxchips: Number of chips to scan for | |
| * | |
| * This fills out all the uninitialized function pointers | |
| * with the defaults. | |
| * The flash ID is read and the mtd/chip structures are | |
| * filled with the appropriate values. | |
| * The mtd->owner field must be set to the module of the caller | |
| * | |
| */ | |
| int nand_scan(struct mtd_info *mtd, int maxchips) | |
| { | |
| int ret; | |
| /* Many callers got this wrong, so check for it for a while... */ | |
| if (!mtd->owner && caller_is_module()) { | |
| printk(KERN_CRIT "nand_scan() called with NULL mtd->owner!\n"); | |
| BUG(); | |
| } | |
| ret = nand_scan_ident(mtd, maxchips); | |
| if (!ret) | |
| ret = nand_scan_tail(mtd); | |
| return ret; | |
| } | |
| /** | |
| * nand_release - [NAND Interface] Free resources held by the NAND device | |
| * @mtd: MTD device structure | |
| */ | |
| void nand_release(struct mtd_info *mtd) | |
| { | |
| struct nand_chip *chip = mtd->priv; | |
| #ifdef CONFIG_MTD_PARTITIONS | |
| /* Deregister partitions */ | |
| del_mtd_partitions(mtd); | |
| #endif | |
| /* Deregister the device */ | |
| del_mtd_device(mtd); | |
| /* Free bad block table memory */ | |
| kfree(chip->bbt); | |
| if (!(chip->options & NAND_OWN_BUFFERS)) | |
| kfree(chip->buffers); | |
| } | |
| EXPORT_SYMBOL_GPL(nand_scan); | |
| EXPORT_SYMBOL_GPL(nand_scan_ident); | |
| EXPORT_SYMBOL_GPL(nand_scan_tail); | |
| EXPORT_SYMBOL_GPL(nand_release); | |
| static int __init nand_base_init(void) | |
| { | |
| led_trigger_register_simple("nand-disk", &nand_led_trigger); | |
| return 0; | |
| } | |
| static void __exit nand_base_exit(void) | |
| { | |
| led_trigger_unregister_simple(nand_led_trigger); | |
| } | |
| module_init(nand_base_init); | |
| module_exit(nand_base_exit); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_AUTHOR("Steven J. Hill <sjhill@realitydiluted.com>, Thomas Gleixner <tglx@linutronix.de>"); | |
| MODULE_DESCRIPTION("Generic NAND flash driver code"); |