| /********************************************************************* | |
| * | |
| * Filename: nsc-ircc.h | |
| * Version: | |
| * Description: | |
| * Status: Experimental. | |
| * Author: Dag Brattli <dagb@cs.uit.no> | |
| * Created at: Fri Nov 13 14:37:40 1998 | |
| * Modified at: Sun Jan 23 17:47:00 2000 | |
| * Modified by: Dag Brattli <dagb@cs.uit.no> | |
| * | |
| * Copyright (c) 1998-2000 Dag Brattli <dagb@cs.uit.no> | |
| * Copyright (c) 1998 Lichen Wang, <lwang@actisys.com> | |
| * Copyright (c) 1998 Actisys Corp., www.actisys.com | |
| * All Rights Reserved | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License as | |
| * published by the Free Software Foundation; either version 2 of | |
| * the License, or (at your option) any later version. | |
| * | |
| * Neither Dag Brattli nor University of Tromsø admit liability nor | |
| * provide warranty for any of this software. This material is | |
| * provided "AS-IS" and at no charge. | |
| * | |
| ********************************************************************/ | |
| #ifndef NSC_IRCC_H | |
| #define NSC_IRCC_H | |
| #include <linux/time.h> | |
| #include <linux/spinlock.h> | |
| #include <linux/pm.h> | |
| #include <linux/types.h> | |
| #include <asm/io.h> | |
| /* DMA modes needed */ | |
| #define DMA_TX_MODE 0x08 /* Mem to I/O, ++, demand. */ | |
| #define DMA_RX_MODE 0x04 /* I/O to mem, ++, demand. */ | |
| /* Config registers for the '108 */ | |
| #define CFG_108_BAIC 0x00 | |
| #define CFG_108_CSRT 0x01 | |
| #define CFG_108_MCTL 0x02 | |
| /* Config registers for the '338 */ | |
| #define CFG_338_FER 0x00 | |
| #define CFG_338_FAR 0x01 | |
| #define CFG_338_PTR 0x02 | |
| #define CFG_338_PNP0 0x1b | |
| #define CFG_338_PNP1 0x1c | |
| #define CFG_338_PNP3 0x4f | |
| /* Config registers for the '39x (in the logical device bank) */ | |
| #define CFG_39X_LDN 0x07 /* Logical device number (Super I/O bank) */ | |
| #define CFG_39X_SIOCF1 0x21 /* SuperI/O Config */ | |
| #define CFG_39X_ACT 0x30 /* Device activation */ | |
| #define CFG_39X_BASEH 0x60 /* Device base address (high bits) */ | |
| #define CFG_39X_BASEL 0x61 /* Device base address (low bits) */ | |
| #define CFG_39X_IRQNUM 0x70 /* Interrupt number & wake up enable */ | |
| #define CFG_39X_IRQSEL 0x71 /* Interrupt select (edge/level + polarity) */ | |
| #define CFG_39X_DMA0 0x74 /* DMA 0 configuration */ | |
| #define CFG_39X_DMA1 0x75 /* DMA 1 configuration */ | |
| #define CFG_39X_SPC 0xF0 /* Serial port configuration register */ | |
| /* Flags for configuration register CRF0 */ | |
| #define APEDCRC 0x02 | |
| #define ENBNKSEL 0x01 | |
| /* Set 0 */ | |
| #define TXD 0x00 /* Transmit data port */ | |
| #define RXD 0x00 /* Receive data port */ | |
| /* Register 1 */ | |
| #define IER 0x01 /* Interrupt Enable Register*/ | |
| #define IER_RXHDL_IE 0x01 /* Receiver high data level interrupt */ | |
| #define IER_TXLDL_IE 0x02 /* Transeiver low data level interrupt */ | |
| #define IER_LS_IE 0x04//* Link Status Interrupt */ | |
| #define IER_ETXURI 0x04 /* Tx underrun */ | |
| #define IER_DMA_IE 0x10 /* DMA finished interrupt */ | |
| #define IER_TXEMP_IE 0x20 | |
| #define IER_SFIF_IE 0x40 /* Frame status FIFO intr */ | |
| #define IER_TMR_IE 0x80 /* Timer event */ | |
| #define FCR 0x02 /* (write only) */ | |
| #define FCR_FIFO_EN 0x01 /* Enable FIFO's */ | |
| #define FCR_RXSR 0x02 /* Rx FIFO soft reset */ | |
| #define FCR_TXSR 0x04 /* Tx FIFO soft reset */ | |
| #define FCR_RXTH 0x40 /* Rx FIFO threshold (set to 16) */ | |
| #define FCR_TXTH 0x20 /* Tx FIFO threshold (set to 17) */ | |
| #define EIR 0x02 /* (read only) */ | |
| #define EIR_RXHDL_EV 0x01 | |
| #define EIR_TXLDL_EV 0x02 | |
| #define EIR_LS_EV 0x04 | |
| #define EIR_DMA_EV 0x10 | |
| #define EIR_TXEMP_EV 0x20 | |
| #define EIR_SFIF_EV 0x40 | |
| #define EIR_TMR_EV 0x80 | |
| #define LCR 0x03 /* Link control register */ | |
| #define LCR_WLS_8 0x03 /* 8 bits */ | |
| #define BSR 0x03 /* Bank select register */ | |
| #define BSR_BKSE 0x80 | |
| #define BANK0 LCR_WLS_8 /* Must make sure that we set 8N1 */ | |
| #define BANK1 0x80 | |
| #define BANK2 0xe0 | |
| #define BANK3 0xe4 | |
| #define BANK4 0xe8 | |
| #define BANK5 0xec | |
| #define BANK6 0xf0 | |
| #define BANK7 0xf4 | |
| #define MCR 0x04 /* Mode Control Register */ | |
| #define MCR_MODE_MASK ~(0xd0) | |
| #define MCR_UART 0x00 | |
| #define MCR_RESERVED 0x20 | |
| #define MCR_SHARP_IR 0x40 | |
| #define MCR_SIR 0x60 | |
| #define MCR_MIR 0x80 | |
| #define MCR_FIR 0xa0 | |
| #define MCR_CEIR 0xb0 | |
| #define MCR_IR_PLS 0x10 | |
| #define MCR_DMA_EN 0x04 | |
| #define MCR_EN_IRQ 0x08 | |
| #define MCR_TX_DFR 0x08 | |
| #define LSR 0x05 /* Link status register */ | |
| #define LSR_RXDA 0x01 /* Receiver data available */ | |
| #define LSR_TXRDY 0x20 /* Transmitter ready */ | |
| #define LSR_TXEMP 0x40 /* Transmitter empty */ | |
| #define ASCR 0x07 /* Auxillary Status and Control Register */ | |
| #define ASCR_RXF_TOUT 0x01 /* Rx FIFO timeout */ | |
| #define ASCR_FEND_INF 0x02 /* Frame end bytes in rx FIFO */ | |
| #define ASCR_S_EOT 0x04 /* Set end of transmission */ | |
| #define ASCT_RXBSY 0x20 /* Rx busy */ | |
| #define ASCR_TXUR 0x40 /* Transeiver underrun */ | |
| #define ASCR_CTE 0x80 /* Clear timer event */ | |
| /* Bank 2 */ | |
| #define BGDL 0x00 /* Baud Generator Divisor Port (Low Byte) */ | |
| #define BGDH 0x01 /* Baud Generator Divisor Port (High Byte) */ | |
| #define ECR1 0x02 /* Extended Control Register 1 */ | |
| #define ECR1_EXT_SL 0x01 /* Extended Mode Select */ | |
| #define ECR1_DMANF 0x02 /* DMA Fairness */ | |
| #define ECR1_DMATH 0x04 /* DMA Threshold */ | |
| #define ECR1_DMASWP 0x08 /* DMA Swap */ | |
| #define EXCR2 0x04 | |
| #define EXCR2_TFSIZ 0x01 /* Rx FIFO size = 32 */ | |
| #define EXCR2_RFSIZ 0x04 /* Tx FIFO size = 32 */ | |
| #define TXFLV 0x06 /* Tx FIFO level */ | |
| #define RXFLV 0x07 /* Rx FIFO level */ | |
| /* Bank 3 */ | |
| #define MID 0x00 | |
| /* Bank 4 */ | |
| #define TMRL 0x00 /* Timer low byte */ | |
| #define TMRH 0x01 /* Timer high byte */ | |
| #define IRCR1 0x02 /* Infrared control register 1 */ | |
| #define IRCR1_TMR_EN 0x01 /* Timer enable */ | |
| #define TFRLL 0x04 | |
| #define TFRLH 0x05 | |
| #define RFRLL 0x06 | |
| #define RFRLH 0x07 | |
| /* Bank 5 */ | |
| #define IRCR2 0x04 /* Infrared control register 2 */ | |
| #define IRCR2_MDRS 0x04 /* MIR data rate select */ | |
| #define IRCR2_FEND_MD 0x20 /* */ | |
| #define FRM_ST 0x05 /* Frame status FIFO */ | |
| #define FRM_ST_VLD 0x80 /* Frame status FIFO data valid */ | |
| #define FRM_ST_ERR_MSK 0x5f | |
| #define FRM_ST_LOST_FR 0x40 /* Frame lost */ | |
| #define FRM_ST_MAX_LEN 0x10 /* Max frame len exceeded */ | |
| #define FRM_ST_PHY_ERR 0x08 /* Physical layer error */ | |
| #define FRM_ST_BAD_CRC 0x04 | |
| #define FRM_ST_OVR1 0x02 /* Rx FIFO overrun */ | |
| #define FRM_ST_OVR2 0x01 /* Frame status FIFO overrun */ | |
| #define RFLFL 0x06 | |
| #define RFLFH 0x07 | |
| /* Bank 6 */ | |
| #define IR_CFG2 0x00 | |
| #define IR_CFG2_DIS_CRC 0x02 | |
| /* Bank 7 */ | |
| #define IRM_CR 0x07 /* Infrared module control register */ | |
| #define IRM_CR_IRX_MSL 0x40 | |
| #define IRM_CR_AF_MNT 0x80 /* Automatic format */ | |
| /* NSC chip information */ | |
| struct nsc_chip { | |
| char *name; /* Name of chipset */ | |
| int cfg[3]; /* Config registers */ | |
| u_int8_t cid_index; /* Chip identification index reg */ | |
| u_int8_t cid_value; /* Chip identification expected value */ | |
| u_int8_t cid_mask; /* Chip identification revision mask */ | |
| /* Functions for probing and initializing the specific chip */ | |
| int (*probe)(struct nsc_chip *chip, chipio_t *info); | |
| int (*init)(struct nsc_chip *chip, chipio_t *info); | |
| }; | |
| typedef struct nsc_chip nsc_chip_t; | |
| /* For storing entries in the status FIFO */ | |
| struct st_fifo_entry { | |
| int status; | |
| int len; | |
| }; | |
| #define MAX_TX_WINDOW 7 | |
| #define MAX_RX_WINDOW 7 | |
| struct st_fifo { | |
| struct st_fifo_entry entries[MAX_RX_WINDOW]; | |
| int pending_bytes; | |
| int head; | |
| int tail; | |
| int len; | |
| }; | |
| struct frame_cb { | |
| void *start; /* Start of frame in DMA mem */ | |
| int len; /* Lenght of frame in DMA mem */ | |
| }; | |
| struct tx_fifo { | |
| struct frame_cb queue[MAX_TX_WINDOW]; /* Info about frames in queue */ | |
| int ptr; /* Currently being sent */ | |
| int len; /* Lenght of queue */ | |
| int free; /* Next free slot */ | |
| void *tail; /* Next free start in DMA mem */ | |
| }; | |
| /* Private data for each instance */ | |
| struct nsc_ircc_cb { | |
| struct st_fifo st_fifo; /* Info about received frames */ | |
| struct tx_fifo tx_fifo; /* Info about frames to be transmitted */ | |
| struct net_device *netdev; /* Yes! we are some kind of netdevice */ | |
| struct net_device_stats stats; | |
| struct irlap_cb *irlap; /* The link layer we are binded to */ | |
| struct qos_info qos; /* QoS capabilities for this device */ | |
| chipio_t io; /* IrDA controller information */ | |
| iobuff_t tx_buff; /* Transmit buffer */ | |
| iobuff_t rx_buff; /* Receive buffer */ | |
| dma_addr_t tx_buff_dma; | |
| dma_addr_t rx_buff_dma; | |
| __u8 ier; /* Interrupt enable register */ | |
| struct timeval stamp; | |
| struct timeval now; | |
| spinlock_t lock; /* For serializing operations */ | |
| __u32 new_speed; | |
| int index; /* Instance index */ | |
| struct platform_device *pldev; | |
| }; | |
| static inline void switch_bank(int iobase, int bank) | |
| { | |
| outb(bank, iobase+BSR); | |
| } | |
| #endif /* NSC_IRCC_H */ |