| /* ne-h8300.c: A NE2000 clone on H8/300 driver for linux. */ | |
| /* | |
| original ne.c | |
| Written 1992-94 by Donald Becker. | |
| Copyright 1993 United States Government as represented by the | |
| Director, National Security Agency. | |
| This software may be used and distributed according to the terms | |
| of the GNU General Public License, incorporated herein by reference. | |
| The author may be reached as becker@scyld.com, or C/O | |
| Scyld Computing Corporation, 410 Severn Ave., Suite 210, Annapolis MD 21403 | |
| H8/300 modified | |
| Yoshinori Sato <ysato@users.sourceforge.jp> | |
| */ | |
| static const char version1[] = | |
| "ne-h8300.c:v1.00 2004/04/11 ysato\n"; | |
| #include <linux/module.h> | |
| #include <linux/kernel.h> | |
| #include <linux/errno.h> | |
| #include <linux/init.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/delay.h> | |
| #include <linux/netdevice.h> | |
| #include <linux/etherdevice.h> | |
| #include <linux/jiffies.h> | |
| #include <asm/system.h> | |
| #include <asm/io.h> | |
| #include <asm/irq.h> | |
| #include "8390.h" | |
| #define DRV_NAME "ne-h8300" | |
| /* Some defines that people can play with if so inclined. */ | |
| /* Do we perform extra sanity checks on stuff ? */ | |
| /* #define NE_SANITY_CHECK */ | |
| /* Do we implement the read before write bugfix ? */ | |
| /* #define NE_RW_BUGFIX */ | |
| /* Do we have a non std. amount of memory? (in units of 256 byte pages) */ | |
| /* #define PACKETBUF_MEMSIZE 0x40 */ | |
| /* A zero-terminated list of I/O addresses to be probed at boot. */ | |
| /* ---- No user-serviceable parts below ---- */ | |
| #define NE_BASE (dev->base_addr) | |
| #define NE_CMD 0x00 | |
| #define NE_DATAPORT (ei_status.word16?0x20:0x10) /* NatSemi-defined port window offset. */ | |
| #define NE_RESET (ei_status.word16?0x3f:0x1f) /* Issue a read to reset, a write to clear. */ | |
| #define NE_IO_EXTENT (ei_status.word16?0x40:0x20) | |
| #define NESM_START_PG 0x40 /* First page of TX buffer */ | |
| #define NESM_STOP_PG 0x80 /* Last page +1 of RX ring */ | |
| static int ne_probe1(struct net_device *dev, int ioaddr); | |
| static int ne_open(struct net_device *dev); | |
| static int ne_close(struct net_device *dev); | |
| static void ne_reset_8390(struct net_device *dev); | |
| static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, | |
| int ring_page); | |
| static void ne_block_input(struct net_device *dev, int count, | |
| struct sk_buff *skb, int ring_offset); | |
| static void ne_block_output(struct net_device *dev, const int count, | |
| const unsigned char *buf, const int start_page); | |
| static u32 reg_offset[16]; | |
| static int __init init_reg_offset(struct net_device *dev,unsigned long base_addr) | |
| { | |
| struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
| int i; | |
| unsigned char bus_width; | |
| bus_width = *(volatile unsigned char *)ABWCR; | |
| bus_width &= 1 << ((base_addr >> 21) & 7); | |
| for (i = 0; i < sizeof(reg_offset) / sizeof(u32); i++) | |
| if (bus_width == 0) | |
| reg_offset[i] = i * 2 + 1; | |
| else | |
| reg_offset[i] = i; | |
| ei_local->reg_offset = reg_offset; | |
| return 0; | |
| } | |
| static int __initdata h8300_ne_count = 0; | |
| #ifdef CONFIG_H8300H_H8MAX | |
| static unsigned long __initdata h8300_ne_base[] = { 0x800600 }; | |
| static int h8300_ne_irq[] = {EXT_IRQ4}; | |
| #endif | |
| #ifdef CONFIG_H8300H_AKI3068NET | |
| static unsigned long __initdata h8300_ne_base[] = { 0x200000 }; | |
| static int h8300_ne_irq[] = {EXT_IRQ5}; | |
| #endif | |
| static inline int init_dev(struct net_device *dev) | |
| { | |
| if (h8300_ne_count < (sizeof(h8300_ne_base) / sizeof(unsigned long))) { | |
| dev->base_addr = h8300_ne_base[h8300_ne_count]; | |
| dev->irq = h8300_ne_irq[h8300_ne_count]; | |
| h8300_ne_count++; | |
| return 0; | |
| } else | |
| return -ENODEV; | |
| } | |
| /* Probe for various non-shared-memory ethercards. | |
| NEx000-clone boards have a Station Address PROM (SAPROM) in the packet | |
| buffer memory space. NE2000 clones have 0x57,0x57 in bytes 0x0e,0x0f of | |
| the SAPROM, while other supposed NE2000 clones must be detected by their | |
| SA prefix. | |
| Reading the SAPROM from a word-wide card with the 8390 set in byte-wide | |
| mode results in doubled values, which can be detected and compensated for. | |
| The probe is also responsible for initializing the card and filling | |
| in the 'dev' and 'ei_status' structures. | |
| We use the minimum memory size for some ethercard product lines, iff we can't | |
| distinguish models. You can increase the packet buffer size by setting | |
| PACKETBUF_MEMSIZE. Reported Cabletron packet buffer locations are: | |
| E1010 starts at 0x100 and ends at 0x2000. | |
| E1010-x starts at 0x100 and ends at 0x8000. ("-x" means "more memory") | |
| E2010 starts at 0x100 and ends at 0x4000. | |
| E2010-x starts at 0x100 and ends at 0xffff. */ | |
| static int __init do_ne_probe(struct net_device *dev) | |
| { | |
| unsigned int base_addr = dev->base_addr; | |
| SET_MODULE_OWNER(dev); | |
| /* First check any supplied i/o locations. User knows best. <cough> */ | |
| if (base_addr > 0x1ff) /* Check a single specified location. */ | |
| return ne_probe1(dev, base_addr); | |
| else if (base_addr != 0) /* Don't probe at all. */ | |
| return -ENXIO; | |
| return -ENODEV; | |
| } | |
| static void cleanup_card(struct net_device *dev) | |
| { | |
| free_irq(dev->irq, dev); | |
| release_region(dev->base_addr, NE_IO_EXTENT); | |
| } | |
| #ifndef MODULE | |
| struct net_device * __init ne_probe(int unit) | |
| { | |
| struct net_device *dev = alloc_ei_netdev(); | |
| int err; | |
| if (!dev) | |
| return ERR_PTR(-ENOMEM); | |
| if (init_dev(dev)) | |
| return ERR_PTR(-ENODEV); | |
| sprintf(dev->name, "eth%d", unit); | |
| netdev_boot_setup_check(dev); | |
| err = init_reg_offset(dev, dev->base_addr); | |
| if (err) | |
| goto out; | |
| err = do_ne_probe(dev); | |
| if (err) | |
| goto out; | |
| return dev; | |
| out: | |
| free_netdev(dev); | |
| return ERR_PTR(err); | |
| } | |
| #endif | |
| static int __init ne_probe1(struct net_device *dev, int ioaddr) | |
| { | |
| int i; | |
| unsigned char SA_prom[16]; | |
| int wordlength = 2; | |
| const char *name = NULL; | |
| int start_page, stop_page; | |
| int reg0, ret; | |
| static unsigned version_printed; | |
| struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
| unsigned char bus_width; | |
| if (!request_region(ioaddr, NE_IO_EXTENT, DRV_NAME)) | |
| return -EBUSY; | |
| reg0 = inb_p(ioaddr); | |
| if (reg0 == 0xFF) { | |
| ret = -ENODEV; | |
| goto err_out; | |
| } | |
| /* Do a preliminary verification that we have a 8390. */ | |
| { | |
| int regd; | |
| outb_p(E8390_NODMA+E8390_PAGE1+E8390_STOP, ioaddr + E8390_CMD); | |
| regd = inb_p(ioaddr + EI_SHIFT(0x0d)); | |
| outb_p(0xff, ioaddr + EI_SHIFT(0x0d)); | |
| outb_p(E8390_NODMA+E8390_PAGE0, ioaddr + E8390_CMD); | |
| inb_p(ioaddr + EN0_COUNTER0); /* Clear the counter by reading. */ | |
| if (inb_p(ioaddr + EN0_COUNTER0) != 0) { | |
| outb_p(reg0, ioaddr + EI_SHIFT(0)); | |
| outb_p(regd, ioaddr + EI_SHIFT(0x0d)); /* Restore the old values. */ | |
| ret = -ENODEV; | |
| goto err_out; | |
| } | |
| } | |
| if (ei_debug && version_printed++ == 0) | |
| printk(KERN_INFO "%s", version1); | |
| printk(KERN_INFO "NE*000 ethercard probe at %08x:", ioaddr); | |
| /* Read the 16 bytes of station address PROM. | |
| We must first initialize registers, similar to NS8390_init(eifdev, 0). | |
| We can't reliably read the SAPROM address without this. | |
| (I learned the hard way!). */ | |
| { | |
| struct {unsigned char value, offset; } program_seq[] = | |
| { | |
| {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/ | |
| {0x48, EN0_DCFG}, /* Set byte-wide (0x48) access. */ | |
| {0x00, EN0_RCNTLO}, /* Clear the count regs. */ | |
| {0x00, EN0_RCNTHI}, | |
| {0x00, EN0_IMR}, /* Mask completion irq. */ | |
| {0xFF, EN0_ISR}, | |
| {E8390_RXOFF, EN0_RXCR}, /* 0x20 Set to monitor */ | |
| {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */ | |
| {32, EN0_RCNTLO}, | |
| {0x00, EN0_RCNTHI}, | |
| {0x00, EN0_RSARLO}, /* DMA starting at 0x0000. */ | |
| {0x00, EN0_RSARHI}, | |
| {E8390_RREAD+E8390_START, E8390_CMD}, | |
| }; | |
| for (i = 0; i < sizeof(program_seq)/sizeof(program_seq[0]); i++) | |
| outb_p(program_seq[i].value, ioaddr + program_seq[i].offset); | |
| } | |
| bus_width = *(volatile unsigned char *)ABWCR; | |
| bus_width &= 1 << ((ioaddr >> 21) & 7); | |
| ei_status.word16 = (bus_width == 0); /* temporary setting */ | |
| for(i = 0; i < 16 /*sizeof(SA_prom)*/; i++) { | |
| SA_prom[i] = inb_p(ioaddr + NE_DATAPORT); | |
| inb_p(ioaddr + NE_DATAPORT); /* dummy read */ | |
| } | |
| start_page = NESM_START_PG; | |
| stop_page = NESM_STOP_PG; | |
| if (bus_width) | |
| wordlength = 1; | |
| else | |
| outb_p(0x49, ioaddr + EN0_DCFG); | |
| /* Set up the rest of the parameters. */ | |
| name = (wordlength == 2) ? "NE2000" : "NE1000"; | |
| if (! dev->irq) { | |
| printk(" failed to detect IRQ line.\n"); | |
| ret = -EAGAIN; | |
| goto err_out; | |
| } | |
| /* Snarf the interrupt now. There's no point in waiting since we cannot | |
| share and the board will usually be enabled. */ | |
| ret = request_irq(dev->irq, ei_interrupt, 0, name, dev); | |
| if (ret) { | |
| printk (" unable to get IRQ %d (errno=%d).\n", dev->irq, ret); | |
| goto err_out; | |
| } | |
| dev->base_addr = ioaddr; | |
| for(i = 0; i < ETHER_ADDR_LEN; i++) { | |
| printk(" %2.2x", SA_prom[i]); | |
| dev->dev_addr[i] = SA_prom[i]; | |
| } | |
| printk("\n%s: %s found at %#x, using IRQ %d.\n", | |
| dev->name, name, ioaddr, dev->irq); | |
| ei_status.name = name; | |
| ei_status.tx_start_page = start_page; | |
| ei_status.stop_page = stop_page; | |
| ei_status.word16 = (wordlength == 2); | |
| ei_status.rx_start_page = start_page + TX_PAGES; | |
| #ifdef PACKETBUF_MEMSIZE | |
| /* Allow the packet buffer size to be overridden by know-it-alls. */ | |
| ei_status.stop_page = ei_status.tx_start_page + PACKETBUF_MEMSIZE; | |
| #endif | |
| ei_status.reset_8390 = &ne_reset_8390; | |
| ei_status.block_input = &ne_block_input; | |
| ei_status.block_output = &ne_block_output; | |
| ei_status.get_8390_hdr = &ne_get_8390_hdr; | |
| ei_status.priv = 0; | |
| dev->open = &ne_open; | |
| dev->stop = &ne_close; | |
| #ifdef CONFIG_NET_POLL_CONTROLLER | |
| dev->poll_controller = ei_poll; | |
| #endif | |
| NS8390_init(dev, 0); | |
| ret = register_netdev(dev); | |
| if (ret) | |
| goto out_irq; | |
| return 0; | |
| out_irq: | |
| free_irq(dev->irq, dev); | |
| err_out: | |
| release_region(ioaddr, NE_IO_EXTENT); | |
| return ret; | |
| } | |
| static int ne_open(struct net_device *dev) | |
| { | |
| ei_open(dev); | |
| return 0; | |
| } | |
| static int ne_close(struct net_device *dev) | |
| { | |
| if (ei_debug > 1) | |
| printk(KERN_DEBUG "%s: Shutting down ethercard.\n", dev->name); | |
| ei_close(dev); | |
| return 0; | |
| } | |
| /* Hard reset the card. This used to pause for the same period that a | |
| 8390 reset command required, but that shouldn't be necessary. */ | |
| static void ne_reset_8390(struct net_device *dev) | |
| { | |
| unsigned long reset_start_time = jiffies; | |
| struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
| if (ei_debug > 1) | |
| printk(KERN_DEBUG "resetting the 8390 t=%ld...", jiffies); | |
| /* DON'T change these to inb_p/outb_p or reset will fail on clones. */ | |
| outb(inb(NE_BASE + NE_RESET), NE_BASE + NE_RESET); | |
| ei_status.txing = 0; | |
| ei_status.dmaing = 0; | |
| /* This check _should_not_ be necessary, omit eventually. */ | |
| while ((inb_p(NE_BASE+EN0_ISR) & ENISR_RESET) == 0) | |
| if (time_after(jiffies, reset_start_time + 2*HZ/100)) { | |
| printk(KERN_WARNING "%s: ne_reset_8390() did not complete.\n", dev->name); | |
| break; | |
| } | |
| outb_p(ENISR_RESET, NE_BASE + EN0_ISR); /* Ack intr. */ | |
| } | |
| /* Grab the 8390 specific header. Similar to the block_input routine, but | |
| we don't need to be concerned with ring wrap as the header will be at | |
| the start of a page, so we optimize accordingly. */ | |
| static void ne_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page) | |
| { | |
| struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
| /* This *shouldn't* happen. If it does, it's the last thing you'll see */ | |
| if (ei_status.dmaing) | |
| { | |
| printk(KERN_EMERG "%s: DMAing conflict in ne_get_8390_hdr " | |
| "[DMAstat:%d][irqlock:%d].\n", | |
| dev->name, ei_status.dmaing, ei_status.irqlock); | |
| return; | |
| } | |
| ei_status.dmaing |= 0x01; | |
| outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, NE_BASE + NE_CMD); | |
| outb_p(sizeof(struct e8390_pkt_hdr), NE_BASE + EN0_RCNTLO); | |
| outb_p(0, NE_BASE + EN0_RCNTHI); | |
| outb_p(0, NE_BASE + EN0_RSARLO); /* On page boundary */ | |
| outb_p(ring_page, NE_BASE + EN0_RSARHI); | |
| outb_p(E8390_RREAD+E8390_START, NE_BASE + NE_CMD); | |
| if (ei_status.word16) { | |
| int len; | |
| unsigned short *p = (unsigned short *)hdr; | |
| for (len = sizeof(struct e8390_pkt_hdr)>>1; len > 0; len--) | |
| *p++ = inw(NE_BASE + NE_DATAPORT); | |
| } else | |
| insb(NE_BASE + NE_DATAPORT, hdr, sizeof(struct e8390_pkt_hdr)); | |
| outb_p(ENISR_RDC, NE_BASE + EN0_ISR); /* Ack intr. */ | |
| ei_status.dmaing &= ~0x01; | |
| le16_to_cpus(&hdr->count); | |
| } | |
| /* Block input and output, similar to the Crynwr packet driver. If you | |
| are porting to a new ethercard, look at the packet driver source for hints. | |
| The NEx000 doesn't share the on-board packet memory -- you have to put | |
| the packet out through the "remote DMA" dataport using outb. */ | |
| static void ne_block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset) | |
| { | |
| struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
| #ifdef NE_SANITY_CHECK | |
| int xfer_count = count; | |
| #endif | |
| char *buf = skb->data; | |
| /* This *shouldn't* happen. If it does, it's the last thing you'll see */ | |
| if (ei_status.dmaing) | |
| { | |
| printk(KERN_EMERG "%s: DMAing conflict in ne_block_input " | |
| "[DMAstat:%d][irqlock:%d].\n", | |
| dev->name, ei_status.dmaing, ei_status.irqlock); | |
| return; | |
| } | |
| ei_status.dmaing |= 0x01; | |
| outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, NE_BASE + NE_CMD); | |
| outb_p(count & 0xff, NE_BASE + EN0_RCNTLO); | |
| outb_p(count >> 8, NE_BASE + EN0_RCNTHI); | |
| outb_p(ring_offset & 0xff, NE_BASE + EN0_RSARLO); | |
| outb_p(ring_offset >> 8, NE_BASE + EN0_RSARHI); | |
| outb_p(E8390_RREAD+E8390_START, NE_BASE + NE_CMD); | |
| if (ei_status.word16) | |
| { | |
| int len; | |
| unsigned short *p = (unsigned short *)buf; | |
| for (len = count>>1; len > 0; len--) | |
| *p++ = inw(NE_BASE + NE_DATAPORT); | |
| if (count & 0x01) | |
| { | |
| buf[count-1] = inb(NE_BASE + NE_DATAPORT); | |
| #ifdef NE_SANITY_CHECK | |
| xfer_count++; | |
| #endif | |
| } | |
| } else { | |
| insb(NE_BASE + NE_DATAPORT, buf, count); | |
| } | |
| #ifdef NE_SANITY_CHECK | |
| /* This was for the ALPHA version only, but enough people have | |
| been encountering problems so it is still here. If you see | |
| this message you either 1) have a slightly incompatible clone | |
| or 2) have noise/speed problems with your bus. */ | |
| if (ei_debug > 1) | |
| { | |
| /* DMA termination address check... */ | |
| int addr, tries = 20; | |
| do { | |
| /* DON'T check for 'inb_p(EN0_ISR) & ENISR_RDC' here | |
| -- it's broken for Rx on some cards! */ | |
| int high = inb_p(NE_BASE + EN0_RSARHI); | |
| int low = inb_p(NE_BASE + EN0_RSARLO); | |
| addr = (high << 8) + low; | |
| if (((ring_offset + xfer_count) & 0xff) == low) | |
| break; | |
| } while (--tries > 0); | |
| if (tries <= 0) | |
| printk(KERN_WARNING "%s: RX transfer address mismatch," | |
| "%#4.4x (expected) vs. %#4.4x (actual).\n", | |
| dev->name, ring_offset + xfer_count, addr); | |
| } | |
| #endif | |
| outb_p(ENISR_RDC, NE_BASE + EN0_ISR); /* Ack intr. */ | |
| ei_status.dmaing &= ~0x01; | |
| } | |
| static void ne_block_output(struct net_device *dev, int count, | |
| const unsigned char *buf, const int start_page) | |
| { | |
| struct ei_device *ei_local = (struct ei_device *) netdev_priv(dev); | |
| unsigned long dma_start; | |
| #ifdef NE_SANITY_CHECK | |
| int retries = 0; | |
| #endif | |
| /* Round the count up for word writes. Do we need to do this? | |
| What effect will an odd byte count have on the 8390? | |
| I should check someday. */ | |
| if (ei_status.word16 && (count & 0x01)) | |
| count++; | |
| /* This *shouldn't* happen. If it does, it's the last thing you'll see */ | |
| if (ei_status.dmaing) | |
| { | |
| printk(KERN_EMERG "%s: DMAing conflict in ne_block_output." | |
| "[DMAstat:%d][irqlock:%d]\n", | |
| dev->name, ei_status.dmaing, ei_status.irqlock); | |
| return; | |
| } | |
| ei_status.dmaing |= 0x01; | |
| /* We should already be in page 0, but to be safe... */ | |
| outb_p(E8390_PAGE0+E8390_START+E8390_NODMA, NE_BASE + NE_CMD); | |
| #ifdef NE_SANITY_CHECK | |
| retry: | |
| #endif | |
| #ifdef NE8390_RW_BUGFIX | |
| /* Handle the read-before-write bug the same way as the | |
| Crynwr packet driver -- the NatSemi method doesn't work. | |
| Actually this doesn't always work either, but if you have | |
| problems with your NEx000 this is better than nothing! */ | |
| outb_p(0x42, NE_BASE + EN0_RCNTLO); | |
| outb_p(0x00, NE_BASE + EN0_RCNTHI); | |
| outb_p(0x42, NE_BASE + EN0_RSARLO); | |
| outb_p(0x00, NE_BASE + EN0_RSARHI); | |
| outb_p(E8390_RREAD+E8390_START, NE_BASE + NE_CMD); | |
| /* Make certain that the dummy read has occurred. */ | |
| udelay(6); | |
| #endif | |
| outb_p(ENISR_RDC, NE_BASE + EN0_ISR); | |
| /* Now the normal output. */ | |
| outb_p(count & 0xff, NE_BASE + EN0_RCNTLO); | |
| outb_p(count >> 8, NE_BASE + EN0_RCNTHI); | |
| outb_p(0x00, NE_BASE + EN0_RSARLO); | |
| outb_p(start_page, NE_BASE + EN0_RSARHI); | |
| outb_p(E8390_RWRITE+E8390_START, NE_BASE + NE_CMD); | |
| if (ei_status.word16) { | |
| int len; | |
| unsigned short *p = (unsigned short *)buf; | |
| for (len = count>>1; len > 0; len--) | |
| outw(*p++, NE_BASE + NE_DATAPORT); | |
| } else { | |
| outsb(NE_BASE + NE_DATAPORT, buf, count); | |
| } | |
| dma_start = jiffies; | |
| #ifdef NE_SANITY_CHECK | |
| /* This was for the ALPHA version only, but enough people have | |
| been encountering problems so it is still here. */ | |
| if (ei_debug > 1) | |
| { | |
| /* DMA termination address check... */ | |
| int addr, tries = 20; | |
| do { | |
| int high = inb_p(NE_BASE + EN0_RSARHI); | |
| int low = inb_p(NE_BASE + EN0_RSARLO); | |
| addr = (high << 8) + low; | |
| if ((start_page << 8) + count == addr) | |
| break; | |
| } while (--tries > 0); | |
| if (tries <= 0) | |
| { | |
| printk(KERN_WARNING "%s: Tx packet transfer address mismatch," | |
| "%#4.4x (expected) vs. %#4.4x (actual).\n", | |
| dev->name, (start_page << 8) + count, addr); | |
| if (retries++ == 0) | |
| goto retry; | |
| } | |
| } | |
| #endif | |
| while ((inb_p(NE_BASE + EN0_ISR) & ENISR_RDC) == 0) | |
| if (time_after(jiffies, dma_start + 2*HZ/100)) { /* 20ms */ | |
| printk(KERN_WARNING "%s: timeout waiting for Tx RDC.\n", dev->name); | |
| ne_reset_8390(dev); | |
| NS8390_init(dev,1); | |
| break; | |
| } | |
| outb_p(ENISR_RDC, NE_BASE + EN0_ISR); /* Ack intr. */ | |
| ei_status.dmaing &= ~0x01; | |
| return; | |
| } | |
| #ifdef MODULE | |
| #define MAX_NE_CARDS 1 /* Max number of NE cards per module */ | |
| static struct net_device *dev_ne[MAX_NE_CARDS]; | |
| static int io[MAX_NE_CARDS]; | |
| static int irq[MAX_NE_CARDS]; | |
| static int bad[MAX_NE_CARDS]; /* 0xbad = bad sig or no reset ack */ | |
| module_param_array(io, int, NULL, 0); | |
| module_param_array(irq, int, NULL, 0); | |
| module_param_array(bad, int, NULL, 0); | |
| MODULE_PARM_DESC(io, "I/O base address(es)"); | |
| MODULE_PARM_DESC(irq, "IRQ number(s)"); | |
| MODULE_DESCRIPTION("H8/300 NE2000 Ethernet driver"); | |
| MODULE_LICENSE("GPL"); | |
| /* This is set up so that no ISA autoprobe takes place. We can't guarantee | |
| that the ne2k probe is the last 8390 based probe to take place (as it | |
| is at boot) and so the probe will get confused by any other 8390 cards. | |
| ISA device autoprobes on a running machine are not recommended anyway. */ | |
| int init_module(void) | |
| { | |
| int this_dev, found = 0; | |
| int err; | |
| for (this_dev = 0; this_dev < MAX_NE_CARDS; this_dev++) { | |
| struct net_device *dev = alloc_ei_netdev(); | |
| if (!dev) | |
| break; | |
| if (io[this_dev]) { | |
| dev->irq = irq[this_dev]; | |
| dev->mem_end = bad[this_dev]; | |
| dev->base_addr = io[this_dev]; | |
| } else { | |
| dev->base_addr = h8300_ne_base[this_dev]; | |
| dev->irq = h8300_ne_irq[this_dev]; | |
| } | |
| err = init_reg_offset(dev, dev->base_addr); | |
| if (!err) { | |
| if (do_ne_probe(dev) == 0) { | |
| dev_ne[found++] = dev; | |
| continue; | |
| } | |
| } | |
| free_netdev(dev); | |
| if (found) | |
| break; | |
| if (io[this_dev] != 0) | |
| printk(KERN_WARNING "ne.c: No NE*000 card found at i/o = %#x\n", dev->base_addr); | |
| else | |
| printk(KERN_NOTICE "ne.c: You must supply \"io=0xNNN\" value(s) for ISA cards.\n"); | |
| return -ENXIO; | |
| } | |
| if (found) | |
| return 0; | |
| return -ENODEV; | |
| } | |
| void cleanup_module(void) | |
| { | |
| int this_dev; | |
| for (this_dev = 0; this_dev < MAX_NE_CARDS; this_dev++) { | |
| struct net_device *dev = dev_ne[this_dev]; | |
| if (dev) { | |
| unregister_netdev(dev); | |
| cleanup_card(dev); | |
| free_netdev(dev); | |
| } | |
| } | |
| } | |
| #endif /* MODULE */ |