| /* smc-ultra32.c: An SMC Ultra32 EISA ethernet driver for linux. | |
| Sources: | |
| This driver is based on (cloned from) the ISA SMC Ultra driver | |
| written by Donald Becker. Modifications to support the EISA | |
| version of the card by Paul Gortmaker and Leonard N. Zubkoff. | |
| This software may be used and distributed according to the terms | |
| of the GNU General Public License, incorporated herein by reference. | |
| Theory of Operation: | |
| The SMC Ultra32C card uses the SMC 83c790 chip which is also | |
| found on the ISA SMC Ultra cards. It has a shared memory mode of | |
| operation that makes it similar to the ISA version of the card. | |
| The main difference is that the EISA card has 32KB of RAM, but | |
| only an 8KB window into that memory. The EISA card also can be | |
| set for a bus-mastering mode of operation via the ECU, but that | |
| is not (and probably will never be) supported by this driver. | |
| The ECU should be run to enable shared memory and to disable the | |
| bus-mastering feature for use with linux. | |
| By programming the 8390 to use only 8KB RAM, the modifications | |
| to the ISA driver can be limited to the probe and initialization | |
| code. This allows easy integration of EISA support into the ISA | |
| driver. However, the driver development kit from SMC provided the | |
| register information for sliding the 8KB window, and hence the 8390 | |
| is programmed to use the full 32KB RAM. | |
| Unfortunately this required code changes outside the probe/init | |
| routines, and thus we decided to separate the EISA driver from | |
| the ISA one. In this way, ISA users don't end up with a larger | |
| driver due to the EISA code, and EISA users don't end up with a | |
| larger driver due to the ISA EtherEZ PIO code. The driver is | |
| similar to the 3c503/16 driver, in that the window must be set | |
| back to the 1st 8KB of space for access to the two 8390 Tx slots. | |
| In testing, using only 8KB RAM (3 Tx / 5 Rx) didn't appear to | |
| be a limiting factor, since the EISA bus could get packets off | |
| the card fast enough, but having the use of lots of RAM as Rx | |
| space is extra insurance if interrupt latencies become excessive. | |
| */ | |
| static const char *version = "smc-ultra32.c: 06/97 v1.00\n"; | |
| #include <linux/module.h> | |
| #include <linux/eisa.h> | |
| #include <linux/kernel.h> | |
| #include <linux/errno.h> | |
| #include <linux/string.h> | |
| #include <linux/init.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/netdevice.h> | |
| #include <linux/etherdevice.h> | |
| #include <asm/io.h> | |
| #include <asm/system.h> | |
| #include "8390.h" | |
| #define DRV_NAME "smc-ultra32" | |
| static int ultra32_probe1(struct net_device *dev, int ioaddr); | |
| static int ultra32_open(struct net_device *dev); | |
| static void ultra32_reset_8390(struct net_device *dev); | |
| static void ultra32_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, | |
| int ring_page); | |
| static void ultra32_block_input(struct net_device *dev, int count, | |
| struct sk_buff *skb, int ring_offset); | |
| static void ultra32_block_output(struct net_device *dev, int count, | |
| const unsigned char *buf, | |
| const int start_page); | |
| static int ultra32_close(struct net_device *dev); | |
| #define ULTRA32_CMDREG 0 /* Offset to ASIC command register. */ | |
| #define ULTRA32_RESET 0x80 /* Board reset, in ULTRA32_CMDREG. */ | |
| #define ULTRA32_MEMENB 0x40 /* Enable the shared memory. */ | |
| #define ULTRA32_NIC_OFFSET 16 /* NIC register offset from the base_addr. */ | |
| #define ULTRA32_IO_EXTENT 32 | |
| #define EN0_ERWCNT 0x08 /* Early receive warning count. */ | |
| /* | |
| * Defines that apply only to the Ultra32 EISA card. Note that | |
| * "smc" = 10011 01101 00011 = 0x4da3, and hence !smc8010.cfg translates | |
| * into an EISA ID of 0x1080A34D | |
| */ | |
| #define ULTRA32_BASE 0xca0 | |
| #define ULTRA32_ID 0x1080a34d | |
| #define ULTRA32_IDPORT (-0x20) /* 0xc80 */ | |
| /* Config regs 1->7 from the EISA !SMC8010.CFG file. */ | |
| #define ULTRA32_CFG1 0x04 /* 0xca4 */ | |
| #define ULTRA32_CFG2 0x05 /* 0xca5 */ | |
| #define ULTRA32_CFG3 (-0x18) /* 0xc88 */ | |
| #define ULTRA32_CFG4 (-0x17) /* 0xc89 */ | |
| #define ULTRA32_CFG5 (-0x16) /* 0xc8a */ | |
| #define ULTRA32_CFG6 (-0x15) /* 0xc8b */ | |
| #define ULTRA32_CFG7 0x0d /* 0xcad */ | |
| static void cleanup_card(struct net_device *dev) | |
| { | |
| int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; | |
| /* NB: ultra32_close_card() does free_irq */ | |
| release_region(ioaddr, ULTRA32_IO_EXTENT); | |
| iounmap(ei_status.mem); | |
| } | |
| /* Probe for the Ultra32. This looks like a 8013 with the station | |
| address PROM at I/O ports <base>+8 to <base>+13, with a checksum | |
| following. | |
| */ | |
| struct net_device * __init ultra32_probe(int unit) | |
| { | |
| struct net_device *dev; | |
| int base; | |
| int irq; | |
| int err = -ENODEV; | |
| if (!EISA_bus) | |
| return ERR_PTR(-ENODEV); | |
| dev = alloc_ei_netdev(); | |
| if (!dev) | |
| return ERR_PTR(-ENOMEM); | |
| if (unit >= 0) { | |
| sprintf(dev->name, "eth%d", unit); | |
| netdev_boot_setup_check(dev); | |
| } | |
| SET_MODULE_OWNER(dev); | |
| irq = dev->irq; | |
| /* EISA spec allows for up to 16 slots, but 8 is typical. */ | |
| for (base = 0x1000 + ULTRA32_BASE; base < 0x9000; base += 0x1000) { | |
| if (ultra32_probe1(dev, base) == 0) | |
| break; | |
| dev->irq = irq; | |
| } | |
| if (base >= 0x9000) | |
| goto out; | |
| err = register_netdev(dev); | |
| if (err) | |
| goto out1; | |
| return dev; | |
| out1: | |
| cleanup_card(dev); | |
| out: | |
| free_netdev(dev); | |
| return ERR_PTR(err); | |
| } | |
| static int __init ultra32_probe1(struct net_device *dev, int ioaddr) | |
| { | |
| int i, edge, media, retval; | |
| int checksum = 0; | |
| const char *model_name; | |
| static unsigned version_printed; | |
| /* Values from various config regs. */ | |
| unsigned char idreg; | |
| unsigned char reg4; | |
| const char *ifmap[] = {"UTP No Link", "", "UTP/AUI", "UTP/BNC"}; | |
| if (!request_region(ioaddr, ULTRA32_IO_EXTENT, DRV_NAME)) | |
| return -EBUSY; | |
| if (inb(ioaddr + ULTRA32_IDPORT) == 0xff || | |
| inl(ioaddr + ULTRA32_IDPORT) != ULTRA32_ID) { | |
| retval = -ENODEV; | |
| goto out; | |
| } | |
| media = inb(ioaddr + ULTRA32_CFG7) & 0x03; | |
| edge = inb(ioaddr + ULTRA32_CFG5) & 0x08; | |
| printk("SMC Ultra32 in EISA Slot %d, Media: %s, %s IRQs.\n", | |
| ioaddr >> 12, ifmap[media], | |
| (edge ? "Edge Triggered" : "Level Sensitive")); | |
| idreg = inb(ioaddr + 7); | |
| reg4 = inb(ioaddr + 4) & 0x7f; | |
| /* Check the ID nibble. */ | |
| if ((idreg & 0xf0) != 0x20) { /* SMC Ultra */ | |
| retval = -ENODEV; | |
| goto out; | |
| } | |
| /* Select the station address register set. */ | |
| outb(reg4, ioaddr + 4); | |
| for (i = 0; i < 8; i++) | |
| checksum += inb(ioaddr + 8 + i); | |
| if ((checksum & 0xff) != 0xff) { | |
| retval = -ENODEV; | |
| goto out; | |
| } | |
| if (ei_debug && version_printed++ == 0) | |
| printk(version); | |
| model_name = "SMC Ultra32"; | |
| printk("%s: %s at 0x%X,", dev->name, model_name, ioaddr); | |
| for (i = 0; i < 6; i++) | |
| printk(" %2.2X", dev->dev_addr[i] = inb(ioaddr + 8 + i)); | |
| /* Switch from the station address to the alternate register set and | |
| read the useful registers there. */ | |
| outb(0x80 | reg4, ioaddr + 4); | |
| /* Enable FINE16 mode to avoid BIOS ROM width mismatches @ reboot. */ | |
| outb(0x80 | inb(ioaddr + 0x0c), ioaddr + 0x0c); | |
| /* Reset RAM addr. */ | |
| outb(0x00, ioaddr + 0x0b); | |
| /* Switch back to the station address register set so that the | |
| MS-DOS driver can find the card after a warm boot. */ | |
| outb(reg4, ioaddr + 4); | |
| if ((inb(ioaddr + ULTRA32_CFG5) & 0x40) == 0) { | |
| printk("\nsmc-ultra32: Card RAM is disabled! " | |
| "Run EISA config utility.\n"); | |
| retval = -ENODEV; | |
| goto out; | |
| } | |
| if ((inb(ioaddr + ULTRA32_CFG2) & 0x04) == 0) | |
| printk("\nsmc-ultra32: Ignoring Bus-Master enable bit. " | |
| "Run EISA config utility.\n"); | |
| if (dev->irq < 2) { | |
| unsigned char irqmap[] = {0, 9, 3, 5, 7, 10, 11, 15}; | |
| int irq = irqmap[inb(ioaddr + ULTRA32_CFG5) & 0x07]; | |
| if (irq == 0) { | |
| printk(", failed to detect IRQ line.\n"); | |
| retval = -EAGAIN; | |
| goto out; | |
| } | |
| dev->irq = irq; | |
| } | |
| /* The 8390 isn't at the base address, so fake the offset */ | |
| dev->base_addr = ioaddr + ULTRA32_NIC_OFFSET; | |
| /* Save RAM address in the unused reg0 to avoid excess inb's. */ | |
| ei_status.reg0 = inb(ioaddr + ULTRA32_CFG3) & 0xfc; | |
| dev->mem_start = 0xc0000 + ((ei_status.reg0 & 0x7c) << 11); | |
| ei_status.name = model_name; | |
| ei_status.word16 = 1; | |
| ei_status.tx_start_page = 0; | |
| ei_status.rx_start_page = TX_PAGES; | |
| /* All Ultra32 cards have 32KB memory with an 8KB window. */ | |
| ei_status.stop_page = 128; | |
| ei_status.mem = ioremap(dev->mem_start, 0x2000); | |
| if (!ei_status.mem) { | |
| printk(", failed to ioremap.\n"); | |
| retval = -ENOMEM; | |
| goto out; | |
| } | |
| dev->mem_end = dev->mem_start + 0x1fff; | |
| printk(", IRQ %d, 32KB memory, 8KB window at 0x%lx-0x%lx.\n", | |
| dev->irq, dev->mem_start, dev->mem_end); | |
| ei_status.block_input = &ultra32_block_input; | |
| ei_status.block_output = &ultra32_block_output; | |
| ei_status.get_8390_hdr = &ultra32_get_8390_hdr; | |
| ei_status.reset_8390 = &ultra32_reset_8390; | |
| dev->open = &ultra32_open; | |
| dev->stop = &ultra32_close; | |
| #ifdef CONFIG_NET_POLL_CONTROLLER | |
| dev->poll_controller = ei_poll; | |
| #endif | |
| NS8390_init(dev, 0); | |
| return 0; | |
| out: | |
| release_region(ioaddr, ULTRA32_IO_EXTENT); | |
| return retval; | |
| } | |
| static int ultra32_open(struct net_device *dev) | |
| { | |
| int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; /* ASIC addr */ | |
| int irq_flags = (inb(ioaddr + ULTRA32_CFG5) & 0x08) ? 0 : IRQF_SHARED; | |
| int retval; | |
| retval = request_irq(dev->irq, ei_interrupt, irq_flags, dev->name, dev); | |
| if (retval) | |
| return retval; | |
| outb(ULTRA32_MEMENB, ioaddr); /* Enable Shared Memory. */ | |
| outb(0x80, ioaddr + ULTRA32_CFG6); /* Enable Interrupts. */ | |
| outb(0x84, ioaddr + 5); /* Enable MEM16 & Disable Bus Master. */ | |
| outb(0x01, ioaddr + 6); /* Enable Interrupts. */ | |
| /* Set the early receive warning level in window 0 high enough not | |
| to receive ERW interrupts. */ | |
| outb_p(E8390_NODMA+E8390_PAGE0, dev->base_addr); | |
| outb(0xff, dev->base_addr + EN0_ERWCNT); | |
| ei_open(dev); | |
| return 0; | |
| } | |
| static int ultra32_close(struct net_device *dev) | |
| { | |
| int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; /* CMDREG */ | |
| netif_stop_queue(dev); | |
| if (ei_debug > 1) | |
| printk("%s: Shutting down ethercard.\n", dev->name); | |
| outb(0x00, ioaddr + ULTRA32_CFG6); /* Disable Interrupts. */ | |
| outb(0x00, ioaddr + 6); /* Disable interrupts. */ | |
| free_irq(dev->irq, dev); | |
| NS8390_init(dev, 0); | |
| return 0; | |
| } | |
| static void ultra32_reset_8390(struct net_device *dev) | |
| { | |
| int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; /* ASIC base addr */ | |
| outb(ULTRA32_RESET, ioaddr); | |
| if (ei_debug > 1) printk("resetting Ultra32, t=%ld...", jiffies); | |
| ei_status.txing = 0; | |
| outb(ULTRA32_MEMENB, ioaddr); /* Enable Shared Memory. */ | |
| outb(0x80, ioaddr + ULTRA32_CFG6); /* Enable Interrupts. */ | |
| outb(0x84, ioaddr + 5); /* Enable MEM16 & Disable Bus Master. */ | |
| outb(0x01, ioaddr + 6); /* Enable Interrupts. */ | |
| if (ei_debug > 1) printk("reset done\n"); | |
| return; | |
| } | |
| /* Grab the 8390 specific header. Similar to the block_input routine, but | |
| we don't need to be concerned with ring wrap as the header will be at | |
| the start of a page, so we optimize accordingly. */ | |
| static void ultra32_get_8390_hdr(struct net_device *dev, | |
| struct e8390_pkt_hdr *hdr, | |
| int ring_page) | |
| { | |
| void __iomem *hdr_start = ei_status.mem + ((ring_page & 0x1f) << 8); | |
| unsigned int RamReg = dev->base_addr - ULTRA32_NIC_OFFSET + ULTRA32_CFG3; | |
| /* Select correct 8KB Window. */ | |
| outb(ei_status.reg0 | ((ring_page & 0x60) >> 5), RamReg); | |
| #ifdef __BIG_ENDIAN | |
| /* Officially this is what we are doing, but the readl() is faster */ | |
| /* unfortunately it isn't endian aware of the struct */ | |
| memcpy_fromio(hdr, hdr_start, sizeof(struct e8390_pkt_hdr)); | |
| hdr->count = le16_to_cpu(hdr->count); | |
| #else | |
| ((unsigned int*)hdr)[0] = readl(hdr_start); | |
| #endif | |
| } | |
| /* Block input and output are easy on shared memory ethercards, the only | |
| complication is when the ring buffer wraps, or in this case, when a | |
| packet spans an 8KB boundary. Note that the current 8KB segment is | |
| already set by the get_8390_hdr routine. */ | |
| static void ultra32_block_input(struct net_device *dev, | |
| int count, | |
| struct sk_buff *skb, | |
| int ring_offset) | |
| { | |
| void __iomem *xfer_start = ei_status.mem + (ring_offset & 0x1fff); | |
| unsigned int RamReg = dev->base_addr - ULTRA32_NIC_OFFSET + ULTRA32_CFG3; | |
| if ((ring_offset & ~0x1fff) != ((ring_offset + count - 1) & ~0x1fff)) { | |
| int semi_count = 8192 - (ring_offset & 0x1FFF); | |
| memcpy_fromio(skb->data, xfer_start, semi_count); | |
| count -= semi_count; | |
| if (ring_offset < 96*256) { | |
| /* Select next 8KB Window. */ | |
| ring_offset += semi_count; | |
| outb(ei_status.reg0 | ((ring_offset & 0x6000) >> 13), RamReg); | |
| memcpy_fromio(skb->data + semi_count, ei_status.mem, count); | |
| } else { | |
| /* Select first 8KB Window. */ | |
| outb(ei_status.reg0, RamReg); | |
| memcpy_fromio(skb->data + semi_count, ei_status.mem + TX_PAGES * 256, count); | |
| } | |
| } else { | |
| /* Packet is in one chunk -- we can copy + cksum. */ | |
| eth_io_copy_and_sum(skb, xfer_start, count, 0); | |
| } | |
| } | |
| static void ultra32_block_output(struct net_device *dev, | |
| int count, | |
| const unsigned char *buf, | |
| int start_page) | |
| { | |
| void __iomem *xfer_start = ei_status.mem + (start_page<<8); | |
| unsigned int RamReg = dev->base_addr - ULTRA32_NIC_OFFSET + ULTRA32_CFG3; | |
| /* Select first 8KB Window. */ | |
| outb(ei_status.reg0, RamReg); | |
| memcpy_toio(xfer_start, buf, count); | |
| } | |
| #ifdef MODULE | |
| #define MAX_ULTRA32_CARDS 4 /* Max number of Ultra cards per module */ | |
| static struct net_device *dev_ultra[MAX_ULTRA32_CARDS]; | |
| MODULE_DESCRIPTION("SMC Ultra32 EISA ethernet driver"); | |
| MODULE_LICENSE("GPL"); | |
| int __init init_module(void) | |
| { | |
| int this_dev, found = 0; | |
| for (this_dev = 0; this_dev < MAX_ULTRA32_CARDS; this_dev++) { | |
| struct net_device *dev = ultra32_probe(-1); | |
| if (IS_ERR(dev)) | |
| break; | |
| dev_ultra[found++] = dev; | |
| } | |
| if (found) | |
| return 0; | |
| printk(KERN_WARNING "smc-ultra32.c: No SMC Ultra32 found.\n"); | |
| return -ENXIO; | |
| } | |
| void cleanup_module(void) | |
| { | |
| int this_dev; | |
| for (this_dev = 0; this_dev < MAX_ULTRA32_CARDS; this_dev++) { | |
| struct net_device *dev = dev_ultra[this_dev]; | |
| if (dev) { | |
| unregister_netdev(dev); | |
| cleanup_card(dev); | |
| free_netdev(dev); | |
| } | |
| } | |
| } | |
| #endif /* MODULE */ | |