| /* to be used by qlogicfas and qlogic_cs */ | |
| #ifndef __QLOGICFAS408_H | |
| #define __QLOGICFAS408_H | |
| /*----------------------------------------------------------------*/ | |
| /* Configuration */ | |
| /* Set the following to max out the speed of the PIO PseudoDMA transfers, | |
| again, 0 tends to be slower, but more stable. */ | |
| #define QL_TURBO_PDMA 1 | |
| /* This should be 1 to enable parity detection */ | |
| #define QL_ENABLE_PARITY 1 | |
| /* This will reset all devices when the driver is initialized (during bootup). | |
| The other linux drivers don't do this, but the DOS drivers do, and after | |
| using DOS or some kind of crash or lockup this will bring things back | |
| without requiring a cold boot. It does take some time to recover from a | |
| reset, so it is slower, and I have seen timeouts so that devices weren't | |
| recognized when this was set. */ | |
| #define QL_RESET_AT_START 0 | |
| /* crystal frequency in megahertz (for offset 5 and 9) | |
| Please set this for your card. Most Qlogic cards are 40 Mhz. The | |
| Control Concepts ISA (not VLB) is 24 Mhz */ | |
| #define XTALFREQ 40 | |
| /**********/ | |
| /* DANGER! modify these at your own risk */ | |
| /* SLOWCABLE can usually be reset to zero if you have a clean setup and | |
| proper termination. The rest are for synchronous transfers and other | |
| advanced features if your device can transfer faster than 5Mb/sec. | |
| If you are really curious, email me for a quick howto until I have | |
| something official */ | |
| /**********/ | |
| /*****/ | |
| /* config register 1 (offset 8) options */ | |
| /* This needs to be set to 1 if your cabling is long or noisy */ | |
| #define SLOWCABLE 1 | |
| /*****/ | |
| /* offset 0xc */ | |
| /* This will set fast (10Mhz) synchronous timing when set to 1 | |
| For this to have an effect, FASTCLK must also be 1 */ | |
| #define FASTSCSI 0 | |
| /* This when set to 1 will set a faster sync transfer rate */ | |
| #define FASTCLK 0 /*(XTALFREQ>25?1:0)*/ | |
| /*****/ | |
| /* offset 6 */ | |
| /* This is the sync transfer divisor, XTALFREQ/X will be the maximum | |
| achievable data rate (assuming the rest of the system is capable | |
| and set properly) */ | |
| #define SYNCXFRPD 5 /*(XTALFREQ/5)*/ | |
| /*****/ | |
| /* offset 7 */ | |
| /* This is the count of how many synchronous transfers can take place | |
| i.e. how many reqs can occur before an ack is given. | |
| The maximum value for this is 15, the upper bits can modify | |
| REQ/ACK assertion and deassertion during synchronous transfers | |
| If this is 0, the bus will only transfer asynchronously */ | |
| #define SYNCOFFST 0 | |
| /* for the curious, bits 7&6 control the deassertion delay in 1/2 cycles | |
| of the 40Mhz clock. If FASTCLK is 1, specifying 01 (1/2) will | |
| cause the deassertion to be early by 1/2 clock. Bits 5&4 control | |
| the assertion delay, also in 1/2 clocks (FASTCLK is ignored here). */ | |
| /*----------------------------------------------------------------*/ | |
| struct qlogicfas408_priv { | |
| int qbase; /* Port */ | |
| int qinitid; /* initiator ID */ | |
| int qabort; /* Flag to cause an abort */ | |
| int qlirq; /* IRQ being used */ | |
| int int_type; /* type of irq, 2 for ISA board, 0 for PCMCIA */ | |
| char qinfo[80]; /* description */ | |
| struct scsi_cmnd *qlcmd; /* current command being processed */ | |
| struct Scsi_Host *shost; /* pointer back to host */ | |
| struct qlogicfas408_priv *next; /* next private struct */ | |
| }; | |
| /* The qlogic card uses two register maps - These macros select which one */ | |
| #define REG0 ( outb( inb( qbase + 0xd ) & 0x7f , qbase + 0xd ), outb( 4 , qbase + 0xd )) | |
| #define REG1 ( outb( inb( qbase + 0xd ) | 0x80 , qbase + 0xd ), outb( 0xb4 | int_type, qbase + 0xd )) | |
| /* following is watchdog timeout in microseconds */ | |
| #define WATCHDOG 5000000 | |
| /*----------------------------------------------------------------*/ | |
| /* the following will set the monitor border color (useful to find | |
| where something crashed or gets stuck at and as a simple profiler) */ | |
| #define rtrc(i) {} | |
| #define get_priv_by_cmd(x) (struct qlogicfas408_priv *)&((x)->device->host->hostdata[0]) | |
| #define get_priv_by_host(x) (struct qlogicfas408_priv *)&((x)->hostdata[0]) | |
| irqreturn_t qlogicfas408_ihandl(int irq, void *dev_id); | |
| int qlogicfas408_queuecommand(struct scsi_cmnd * cmd, | |
| void (*done) (struct scsi_cmnd *)); | |
| int qlogicfas408_biosparam(struct scsi_device * disk, | |
| struct block_device *dev, | |
| sector_t capacity, int ip[]); | |
| int qlogicfas408_abort(struct scsi_cmnd * cmd); | |
| int qlogicfas408_bus_reset(struct scsi_cmnd * cmd); | |
| const char *qlogicfas408_info(struct Scsi_Host *host); | |
| int qlogicfas408_get_chip_type(int qbase, int int_type); | |
| void qlogicfas408_setup(int qbase, int id, int int_type); | |
| int qlogicfas408_detect(int qbase, int int_type); | |
| void qlogicfas408_disable_ints(struct qlogicfas408_priv *priv); | |
| #endif /* __QLOGICFAS408_H */ | |