| #ifndef __LINUX_ETRAX_USB_H | |
| #define __LINUX_ETRAX_USB_H | |
| #include <linux/types.h> | |
| #include <linux/list.h> | |
| typedef struct USB_IN_Desc { | |
| volatile __u16 sw_len; | |
| volatile __u16 command; | |
| volatile unsigned long next; | |
| volatile unsigned long buf; | |
| volatile __u16 hw_len; | |
| volatile __u16 status; | |
| } USB_IN_Desc_t; | |
| typedef struct USB_SB_Desc { | |
| volatile __u16 sw_len; | |
| volatile __u16 command; | |
| volatile unsigned long next; | |
| volatile unsigned long buf; | |
| __u32 dummy; | |
| } USB_SB_Desc_t; | |
| typedef struct USB_EP_Desc { | |
| volatile __u16 hw_len; | |
| volatile __u16 command; | |
| volatile unsigned long sub; | |
| volatile unsigned long next; | |
| __u32 dummy; | |
| } USB_EP_Desc_t; | |
| struct virt_root_hub { | |
| int devnum; | |
| void *urb; | |
| void *int_addr; | |
| int send; | |
| int interval; | |
| int numports; | |
| struct timer_list rh_int_timer; | |
| volatile __u16 wPortChange_1; | |
| volatile __u16 wPortChange_2; | |
| volatile __u16 prev_wPortStatus_1; | |
| volatile __u16 prev_wPortStatus_2; | |
| }; | |
| struct etrax_usb_intr_traffic { | |
| int sleeping; | |
| int error; | |
| struct wait_queue *wq; | |
| }; | |
| typedef struct etrax_usb_hc { | |
| struct usb_bus *bus; | |
| struct virt_root_hub rh; | |
| struct etrax_usb_intr_traffic intr; | |
| } etrax_hc_t; | |
| typedef enum { | |
| STARTED, | |
| NOT_STARTED, | |
| UNLINK, | |
| TRANSFER_DONE, | |
| WAITING_FOR_DESCR_INTR | |
| } etrax_usb_urb_state_t; | |
| typedef struct etrax_usb_urb_priv { | |
| /* The first_sb field is used for freeing all SB descriptors belonging | |
| to an urb. The corresponding ep descriptor's sub pointer cannot be | |
| used for this since the DMA advances the sub pointer as it processes | |
| the sb list. */ | |
| USB_SB_Desc_t *first_sb; | |
| /* The last_sb field referes to the last SB descriptor that belongs to | |
| this urb. This is important to know so we can free the SB descriptors | |
| that ranges between first_sb and last_sb. */ | |
| USB_SB_Desc_t *last_sb; | |
| /* The rx_offset field is used in ctrl and bulk traffic to keep track | |
| of the offset in the urb's transfer_buffer where incoming data should be | |
| copied to. */ | |
| __u32 rx_offset; | |
| /* Counter used in isochronous transfers to keep track of the | |
| number of packets received/transmitted. */ | |
| __u32 isoc_packet_counter; | |
| /* This field is used to pass information about the urb's current state between | |
| the various interrupt handlers (thus marked volatile). */ | |
| volatile etrax_usb_urb_state_t urb_state; | |
| /* Connection between the submitted urb and ETRAX epid number */ | |
| __u8 epid; | |
| /* The rx_data_list field is used for periodic traffic, to hold | |
| received data for later processing in the the complete_urb functions, | |
| where the data us copied to the urb's transfer_buffer. Basically, we | |
| use this intermediate storage because we don't know when it's safe to | |
| reuse the transfer_buffer (FIXME?). */ | |
| struct list_head rx_data_list; | |
| } etrax_urb_priv_t; | |
| /* This struct is for passing data from the top half to the bottom half. */ | |
| typedef struct usb_interrupt_registers | |
| { | |
| etrax_hc_t *hc; | |
| __u32 r_usb_epid_attn; | |
| __u8 r_usb_status; | |
| __u16 r_usb_rh_port_status_1; | |
| __u16 r_usb_rh_port_status_2; | |
| __u32 r_usb_irq_mask_read; | |
| __u32 r_usb_fm_number; | |
| struct work_struct usb_bh; | |
| } usb_interrupt_registers_t; | |
| /* This struct is for passing data from the isoc top half to the isoc bottom half. */ | |
| typedef struct usb_isoc_complete_data | |
| { | |
| struct urb *urb; | |
| struct work_struct usb_bh; | |
| } usb_isoc_complete_data_t; | |
| /* This struct holds data we get from the rx descriptors for DMA channel 9 | |
| for periodic traffic (intr and isoc). */ | |
| typedef struct rx_data | |
| { | |
| void *data; | |
| int length; | |
| struct list_head list; | |
| } rx_data_t; | |
| typedef struct urb_entry | |
| { | |
| struct urb *urb; | |
| struct list_head list; | |
| } urb_entry_t; | |
| /* --------------------------------------------------------------------------- | |
| Virtual Root HUB | |
| ------------------------------------------------------------------------- */ | |
| /* destination of request */ | |
| #define RH_INTERFACE 0x01 | |
| #define RH_ENDPOINT 0x02 | |
| #define RH_OTHER 0x03 | |
| #define RH_CLASS 0x20 | |
| #define RH_VENDOR 0x40 | |
| /* Requests: bRequest << 8 | bmRequestType */ | |
| #define RH_GET_STATUS 0x0080 | |
| #define RH_CLEAR_FEATURE 0x0100 | |
| #define RH_SET_FEATURE 0x0300 | |
| #define RH_SET_ADDRESS 0x0500 | |
| #define RH_GET_DESCRIPTOR 0x0680 | |
| #define RH_SET_DESCRIPTOR 0x0700 | |
| #define RH_GET_CONFIGURATION 0x0880 | |
| #define RH_SET_CONFIGURATION 0x0900 | |
| #define RH_GET_STATE 0x0280 | |
| #define RH_GET_INTERFACE 0x0A80 | |
| #define RH_SET_INTERFACE 0x0B00 | |
| #define RH_SYNC_FRAME 0x0C80 | |
| /* Our Vendor Specific Request */ | |
| #define RH_SET_EP 0x2000 | |
| /* Hub port features */ | |
| #define RH_PORT_CONNECTION 0x00 | |
| #define RH_PORT_ENABLE 0x01 | |
| #define RH_PORT_SUSPEND 0x02 | |
| #define RH_PORT_OVER_CURRENT 0x03 | |
| #define RH_PORT_RESET 0x04 | |
| #define RH_PORT_POWER 0x08 | |
| #define RH_PORT_LOW_SPEED 0x09 | |
| #define RH_C_PORT_CONNECTION 0x10 | |
| #define RH_C_PORT_ENABLE 0x11 | |
| #define RH_C_PORT_SUSPEND 0x12 | |
| #define RH_C_PORT_OVER_CURRENT 0x13 | |
| #define RH_C_PORT_RESET 0x14 | |
| /* Hub features */ | |
| #define RH_C_HUB_LOCAL_POWER 0x00 | |
| #define RH_C_HUB_OVER_CURRENT 0x01 | |
| #define RH_DEVICE_REMOTE_WAKEUP 0x00 | |
| #define RH_ENDPOINT_STALL 0x01 | |
| /* Our Vendor Specific feature */ | |
| #define RH_REMOVE_EP 0x00 | |
| #define RH_ACK 0x01 | |
| #define RH_REQ_ERR -1 | |
| #define RH_NACK 0x00 | |
| /* Field definitions for */ | |
| #define USB_IN_command__eol__BITNR 0 /* command macros */ | |
| #define USB_IN_command__eol__WIDTH 1 | |
| #define USB_IN_command__eol__no 0 | |
| #define USB_IN_command__eol__yes 1 | |
| #define USB_IN_command__intr__BITNR 3 | |
| #define USB_IN_command__intr__WIDTH 1 | |
| #define USB_IN_command__intr__no 0 | |
| #define USB_IN_command__intr__yes 1 | |
| #define USB_IN_status__eop__BITNR 1 /* status macros. */ | |
| #define USB_IN_status__eop__WIDTH 1 | |
| #define USB_IN_status__eop__no 0 | |
| #define USB_IN_status__eop__yes 1 | |
| #define USB_IN_status__eot__BITNR 5 | |
| #define USB_IN_status__eot__WIDTH 1 | |
| #define USB_IN_status__eot__no 0 | |
| #define USB_IN_status__eot__yes 1 | |
| #define USB_IN_status__error__BITNR 6 | |
| #define USB_IN_status__error__WIDTH 1 | |
| #define USB_IN_status__error__no 0 | |
| #define USB_IN_status__error__yes 1 | |
| #define USB_IN_status__nodata__BITNR 7 | |
| #define USB_IN_status__nodata__WIDTH 1 | |
| #define USB_IN_status__nodata__no 0 | |
| #define USB_IN_status__nodata__yes 1 | |
| #define USB_IN_status__epid__BITNR 8 | |
| #define USB_IN_status__epid__WIDTH 5 | |
| #define USB_EP_command__eol__BITNR 0 | |
| #define USB_EP_command__eol__WIDTH 1 | |
| #define USB_EP_command__eol__no 0 | |
| #define USB_EP_command__eol__yes 1 | |
| #define USB_EP_command__eof__BITNR 1 | |
| #define USB_EP_command__eof__WIDTH 1 | |
| #define USB_EP_command__eof__no 0 | |
| #define USB_EP_command__eof__yes 1 | |
| #define USB_EP_command__intr__BITNR 3 | |
| #define USB_EP_command__intr__WIDTH 1 | |
| #define USB_EP_command__intr__no 0 | |
| #define USB_EP_command__intr__yes 1 | |
| #define USB_EP_command__enable__BITNR 4 | |
| #define USB_EP_command__enable__WIDTH 1 | |
| #define USB_EP_command__enable__no 0 | |
| #define USB_EP_command__enable__yes 1 | |
| #define USB_EP_command__hw_valid__BITNR 5 | |
| #define USB_EP_command__hw_valid__WIDTH 1 | |
| #define USB_EP_command__hw_valid__no 0 | |
| #define USB_EP_command__hw_valid__yes 1 | |
| #define USB_EP_command__epid__BITNR 8 | |
| #define USB_EP_command__epid__WIDTH 5 | |
| #define USB_SB_command__eol__BITNR 0 /* command macros. */ | |
| #define USB_SB_command__eol__WIDTH 1 | |
| #define USB_SB_command__eol__no 0 | |
| #define USB_SB_command__eol__yes 1 | |
| #define USB_SB_command__eot__BITNR 1 | |
| #define USB_SB_command__eot__WIDTH 1 | |
| #define USB_SB_command__eot__no 0 | |
| #define USB_SB_command__eot__yes 1 | |
| #define USB_SB_command__intr__BITNR 3 | |
| #define USB_SB_command__intr__WIDTH 1 | |
| #define USB_SB_command__intr__no 0 | |
| #define USB_SB_command__intr__yes 1 | |
| #define USB_SB_command__tt__BITNR 4 | |
| #define USB_SB_command__tt__WIDTH 2 | |
| #define USB_SB_command__tt__zout 0 | |
| #define USB_SB_command__tt__in 1 | |
| #define USB_SB_command__tt__out 2 | |
| #define USB_SB_command__tt__setup 3 | |
| #define USB_SB_command__rem__BITNR 8 | |
| #define USB_SB_command__rem__WIDTH 6 | |
| #define USB_SB_command__full__BITNR 6 | |
| #define USB_SB_command__full__WIDTH 1 | |
| #define USB_SB_command__full__no 0 | |
| #define USB_SB_command__full__yes 1 | |
| #endif |