| /* | |
| * OHCI HCD (Host Controller Driver) for USB. | |
| * | |
| * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at> | |
| * (C) Copyright 2000-2004 David Brownell <dbrownell@users.sourceforge.net> | |
| * | |
| * This file is licenced under GPL | |
| */ | |
| /*-------------------------------------------------------------------------*/ | |
| /* | |
| * OHCI Root Hub ... the nonsharable stuff | |
| */ | |
| #define dbg_port(hc,label,num,value) \ | |
| ohci_dbg (hc, \ | |
| "%s roothub.portstatus [%d] " \ | |
| "= 0x%08x%s%s%s%s%s%s%s%s%s%s%s%s\n", \ | |
| label, num, temp, \ | |
| (temp & RH_PS_PRSC) ? " PRSC" : "", \ | |
| (temp & RH_PS_OCIC) ? " OCIC" : "", \ | |
| (temp & RH_PS_PSSC) ? " PSSC" : "", \ | |
| (temp & RH_PS_PESC) ? " PESC" : "", \ | |
| (temp & RH_PS_CSC) ? " CSC" : "", \ | |
| \ | |
| (temp & RH_PS_LSDA) ? " LSDA" : "", \ | |
| (temp & RH_PS_PPS) ? " PPS" : "", \ | |
| (temp & RH_PS_PRS) ? " PRS" : "", \ | |
| (temp & RH_PS_POCI) ? " POCI" : "", \ | |
| (temp & RH_PS_PSS) ? " PSS" : "", \ | |
| \ | |
| (temp & RH_PS_PES) ? " PES" : "", \ | |
| (temp & RH_PS_CCS) ? " CCS" : "" \ | |
| ); | |
| /*-------------------------------------------------------------------------*/ | |
| /* hcd->hub_irq_enable() */ | |
| static void ohci_rhsc_enable (struct usb_hcd *hcd) | |
| { | |
| struct ohci_hcd *ohci = hcd_to_ohci (hcd); | |
| ohci_writel (ohci, OHCI_INTR_RHSC, &ohci->regs->intrenable); | |
| } | |
| #define OHCI_SCHED_ENABLES \ | |
| (OHCI_CTRL_CLE|OHCI_CTRL_BLE|OHCI_CTRL_PLE|OHCI_CTRL_IE) | |
| static void dl_done_list (struct ohci_hcd *); | |
| static void finish_unlinks (struct ohci_hcd *, u16); | |
| static int ohci_rh_suspend (struct ohci_hcd *ohci, int autostop) | |
| __releases(ohci->lock) | |
| __acquires(ohci->lock) | |
| { | |
| int status = 0; | |
| ohci->hc_control = ohci_readl (ohci, &ohci->regs->control); | |
| switch (ohci->hc_control & OHCI_CTRL_HCFS) { | |
| case OHCI_USB_RESUME: | |
| ohci_dbg (ohci, "resume/suspend?\n"); | |
| ohci->hc_control &= ~OHCI_CTRL_HCFS; | |
| ohci->hc_control |= OHCI_USB_RESET; | |
| ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); | |
| (void) ohci_readl (ohci, &ohci->regs->control); | |
| /* FALL THROUGH */ | |
| case OHCI_USB_RESET: | |
| status = -EBUSY; | |
| ohci_dbg (ohci, "needs reinit!\n"); | |
| goto done; | |
| case OHCI_USB_SUSPEND: | |
| if (!ohci->autostop) { | |
| ohci_dbg (ohci, "already suspended\n"); | |
| goto done; | |
| } | |
| } | |
| ohci_dbg (ohci, "%s root hub\n", | |
| autostop ? "auto-stop" : "suspend"); | |
| /* First stop any processing */ | |
| if (!autostop && (ohci->hc_control & OHCI_SCHED_ENABLES)) { | |
| ohci->hc_control &= ~OHCI_SCHED_ENABLES; | |
| ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); | |
| ohci->hc_control = ohci_readl (ohci, &ohci->regs->control); | |
| ohci_writel (ohci, OHCI_INTR_SF, &ohci->regs->intrstatus); | |
| /* sched disables take effect on the next frame, | |
| * then the last WDH could take 6+ msec | |
| */ | |
| ohci_dbg (ohci, "stopping schedules ...\n"); | |
| ohci->autostop = 0; | |
| spin_unlock_irq (&ohci->lock); | |
| msleep (8); | |
| spin_lock_irq (&ohci->lock); | |
| } | |
| dl_done_list (ohci); | |
| finish_unlinks (ohci, ohci_frame_no(ohci)); | |
| /* maybe resume can wake root hub */ | |
| if (device_may_wakeup(&ohci_to_hcd(ohci)->self.root_hub->dev) || | |
| autostop) | |
| ohci->hc_control |= OHCI_CTRL_RWE; | |
| else { | |
| ohci_writel (ohci, OHCI_INTR_RHSC, &ohci->regs->intrdisable); | |
| ohci->hc_control &= ~OHCI_CTRL_RWE; | |
| } | |
| /* Suspend hub ... this is the "global (to this bus) suspend" mode, | |
| * which doesn't imply ports will first be individually suspended. | |
| */ | |
| ohci->hc_control &= ~OHCI_CTRL_HCFS; | |
| ohci->hc_control |= OHCI_USB_SUSPEND; | |
| ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); | |
| (void) ohci_readl (ohci, &ohci->regs->control); | |
| /* no resumes until devices finish suspending */ | |
| if (!autostop) { | |
| ohci->next_statechange = jiffies + msecs_to_jiffies (5); | |
| ohci->autostop = 0; | |
| } | |
| done: | |
| return status; | |
| } | |
| static inline struct ed *find_head (struct ed *ed) | |
| { | |
| /* for bulk and control lists */ | |
| while (ed->ed_prev) | |
| ed = ed->ed_prev; | |
| return ed; | |
| } | |
| static int ohci_restart (struct ohci_hcd *ohci); | |
| /* caller has locked the root hub */ | |
| static int ohci_rh_resume (struct ohci_hcd *ohci) | |
| __releases(ohci->lock) | |
| __acquires(ohci->lock) | |
| { | |
| struct usb_hcd *hcd = ohci_to_hcd (ohci); | |
| u32 temp, enables; | |
| int status = -EINPROGRESS; | |
| int autostopped = ohci->autostop; | |
| ohci->autostop = 0; | |
| ohci->hc_control = ohci_readl (ohci, &ohci->regs->control); | |
| if (ohci->hc_control & (OHCI_CTRL_IR | OHCI_SCHED_ENABLES)) { | |
| /* this can happen after resuming a swsusp snapshot */ | |
| if (hcd->state == HC_STATE_RESUMING) { | |
| ohci_dbg (ohci, "BIOS/SMM active, control %03x\n", | |
| ohci->hc_control); | |
| status = -EBUSY; | |
| /* this happens when pmcore resumes HC then root */ | |
| } else { | |
| ohci_dbg (ohci, "duplicate resume\n"); | |
| status = 0; | |
| } | |
| } else switch (ohci->hc_control & OHCI_CTRL_HCFS) { | |
| case OHCI_USB_SUSPEND: | |
| ohci->hc_control &= ~(OHCI_CTRL_HCFS|OHCI_SCHED_ENABLES); | |
| ohci->hc_control |= OHCI_USB_RESUME; | |
| ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); | |
| (void) ohci_readl (ohci, &ohci->regs->control); | |
| ohci_dbg (ohci, "%s root hub\n", | |
| autostopped ? "auto-start" : "resume"); | |
| break; | |
| case OHCI_USB_RESUME: | |
| /* HCFS changes sometime after INTR_RD */ | |
| ohci_info(ohci, "%swakeup\n", | |
| autostopped ? "auto-" : ""); | |
| break; | |
| case OHCI_USB_OPER: | |
| /* this can happen after resuming a swsusp snapshot */ | |
| ohci_dbg (ohci, "snapshot resume? reinit\n"); | |
| status = -EBUSY; | |
| break; | |
| default: /* RESET, we lost power */ | |
| ohci_dbg (ohci, "lost power\n"); | |
| status = -EBUSY; | |
| } | |
| #ifdef CONFIG_PM | |
| if (status == -EBUSY) { | |
| if (!autostopped) { | |
| spin_unlock_irq (&ohci->lock); | |
| (void) ohci_init (ohci); | |
| status = ohci_restart (ohci); | |
| spin_lock_irq (&ohci->lock); | |
| } | |
| return status; | |
| } | |
| #endif | |
| if (status != -EINPROGRESS) | |
| return status; | |
| if (autostopped) | |
| goto skip_resume; | |
| spin_unlock_irq (&ohci->lock); | |
| temp = ohci->num_ports; | |
| while (temp--) { | |
| u32 stat = ohci_readl (ohci, | |
| &ohci->regs->roothub.portstatus [temp]); | |
| /* force global, not selective, resume */ | |
| if (!(stat & RH_PS_PSS)) | |
| continue; | |
| ohci_writel (ohci, RH_PS_POCI, | |
| &ohci->regs->roothub.portstatus [temp]); | |
| } | |
| /* Some controllers (lucent erratum) need extra-long delays */ | |
| msleep (20 /* usb 11.5.1.10 */ + 12 /* 32 msec counter */ + 1); | |
| temp = ohci_readl (ohci, &ohci->regs->control); | |
| temp &= OHCI_CTRL_HCFS; | |
| if (temp != OHCI_USB_RESUME) { | |
| ohci_err (ohci, "controller won't resume\n"); | |
| return -EBUSY; | |
| } | |
| /* disable old schedule state, reinit from scratch */ | |
| ohci_writel (ohci, 0, &ohci->regs->ed_controlhead); | |
| ohci_writel (ohci, 0, &ohci->regs->ed_controlcurrent); | |
| ohci_writel (ohci, 0, &ohci->regs->ed_bulkhead); | |
| ohci_writel (ohci, 0, &ohci->regs->ed_bulkcurrent); | |
| ohci_writel (ohci, 0, &ohci->regs->ed_periodcurrent); | |
| ohci_writel (ohci, (u32) ohci->hcca_dma, &ohci->regs->hcca); | |
| /* Sometimes PCI D3 suspend trashes frame timings ... */ | |
| periodic_reinit (ohci); | |
| /* the following code is executed with ohci->lock held and | |
| * irqs disabled if and only if autostopped is true | |
| */ | |
| skip_resume: | |
| /* interrupts might have been disabled */ | |
| ohci_writel (ohci, OHCI_INTR_INIT, &ohci->regs->intrenable); | |
| if (ohci->ed_rm_list) | |
| ohci_writel (ohci, OHCI_INTR_SF, &ohci->regs->intrenable); | |
| /* Then re-enable operations */ | |
| ohci_writel (ohci, OHCI_USB_OPER, &ohci->regs->control); | |
| (void) ohci_readl (ohci, &ohci->regs->control); | |
| if (!autostopped) | |
| msleep (3); | |
| temp = ohci->hc_control; | |
| temp &= OHCI_CTRL_RWC; | |
| temp |= OHCI_CONTROL_INIT | OHCI_USB_OPER; | |
| ohci->hc_control = temp; | |
| ohci_writel (ohci, temp, &ohci->regs->control); | |
| (void) ohci_readl (ohci, &ohci->regs->control); | |
| /* TRSMRCY */ | |
| if (!autostopped) { | |
| msleep (10); | |
| spin_lock_irq (&ohci->lock); | |
| } | |
| /* now ohci->lock is always held and irqs are always disabled */ | |
| /* keep it alive for more than ~5x suspend + resume costs */ | |
| ohci->next_statechange = jiffies + STATECHANGE_DELAY; | |
| /* maybe turn schedules back on */ | |
| enables = 0; | |
| temp = 0; | |
| if (!ohci->ed_rm_list) { | |
| if (ohci->ed_controltail) { | |
| ohci_writel (ohci, | |
| find_head (ohci->ed_controltail)->dma, | |
| &ohci->regs->ed_controlhead); | |
| enables |= OHCI_CTRL_CLE; | |
| temp |= OHCI_CLF; | |
| } | |
| if (ohci->ed_bulktail) { | |
| ohci_writel (ohci, find_head (ohci->ed_bulktail)->dma, | |
| &ohci->regs->ed_bulkhead); | |
| enables |= OHCI_CTRL_BLE; | |
| temp |= OHCI_BLF; | |
| } | |
| } | |
| if (hcd->self.bandwidth_isoc_reqs || hcd->self.bandwidth_int_reqs) | |
| enables |= OHCI_CTRL_PLE|OHCI_CTRL_IE; | |
| if (enables) { | |
| ohci_dbg (ohci, "restarting schedules ... %08x\n", enables); | |
| ohci->hc_control |= enables; | |
| ohci_writel (ohci, ohci->hc_control, &ohci->regs->control); | |
| if (temp) | |
| ohci_writel (ohci, temp, &ohci->regs->cmdstatus); | |
| (void) ohci_readl (ohci, &ohci->regs->control); | |
| } | |
| return 0; | |
| } | |
| #ifdef CONFIG_PM | |
| static int ohci_bus_suspend (struct usb_hcd *hcd) | |
| { | |
| struct ohci_hcd *ohci = hcd_to_ohci (hcd); | |
| int rc; | |
| spin_lock_irq (&ohci->lock); | |
| if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags))) | |
| rc = -ESHUTDOWN; | |
| else | |
| rc = ohci_rh_suspend (ohci, 0); | |
| spin_unlock_irq (&ohci->lock); | |
| return rc; | |
| } | |
| static int ohci_bus_resume (struct usb_hcd *hcd) | |
| { | |
| struct ohci_hcd *ohci = hcd_to_ohci (hcd); | |
| int rc; | |
| if (time_before (jiffies, ohci->next_statechange)) | |
| msleep(5); | |
| spin_lock_irq (&ohci->lock); | |
| if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags))) | |
| rc = -ESHUTDOWN; | |
| else | |
| rc = ohci_rh_resume (ohci); | |
| spin_unlock_irq (&ohci->lock); | |
| /* poll until we know a device is connected or we autostop */ | |
| if (rc == 0) | |
| usb_hcd_poll_rh_status(hcd); | |
| return rc; | |
| } | |
| #endif /* CONFIG_PM */ | |
| /*-------------------------------------------------------------------------*/ | |
| /* build "status change" packet (one or two bytes) from HC registers */ | |
| static int | |
| ohci_hub_status_data (struct usb_hcd *hcd, char *buf) | |
| { | |
| struct ohci_hcd *ohci = hcd_to_ohci (hcd); | |
| int i, changed = 0, length = 1; | |
| int any_connected = 0, rhsc_enabled = 1; | |
| unsigned long flags; | |
| spin_lock_irqsave (&ohci->lock, flags); | |
| /* undocumented erratum seen on at least rev D */ | |
| if ((ohci->flags & OHCI_QUIRK_AMD756) | |
| && (roothub_a (ohci) & RH_A_NDP) > MAX_ROOT_PORTS) { | |
| ohci_warn (ohci, "bogus NDP, rereads as NDP=%d\n", | |
| ohci_readl (ohci, &ohci->regs->roothub.a) & RH_A_NDP); | |
| /* retry later; "should not happen" */ | |
| goto done; | |
| } | |
| /* init status */ | |
| if (roothub_status (ohci) & (RH_HS_LPSC | RH_HS_OCIC)) | |
| buf [0] = changed = 1; | |
| else | |
| buf [0] = 0; | |
| if (ohci->num_ports > 7) { | |
| buf [1] = 0; | |
| length++; | |
| } | |
| /* look at each port */ | |
| for (i = 0; i < ohci->num_ports; i++) { | |
| u32 status = roothub_portstatus (ohci, i); | |
| /* can't autostop if ports are connected */ | |
| any_connected |= (status & RH_PS_CCS); | |
| if (status & (RH_PS_CSC | RH_PS_PESC | RH_PS_PSSC | |
| | RH_PS_OCIC | RH_PS_PRSC)) { | |
| changed = 1; | |
| if (i < 7) | |
| buf [0] |= 1 << (i + 1); | |
| else | |
| buf [1] |= 1 << (i - 7); | |
| } | |
| } | |
| /* NOTE: vendors didn't always make the same implementation | |
| * choices for RHSC. Sometimes it triggers on an edge (like | |
| * setting and maybe clearing a port status change bit); and | |
| * it's level-triggered on other silicon, active until khubd | |
| * clears all active port status change bits. If it's still | |
| * set (level-triggered) we must disable it and rely on | |
| * polling until khubd re-enables it. | |
| */ | |
| if (ohci_readl (ohci, &ohci->regs->intrstatus) & OHCI_INTR_RHSC) { | |
| ohci_writel (ohci, OHCI_INTR_RHSC, &ohci->regs->intrdisable); | |
| (void) ohci_readl (ohci, &ohci->regs->intrdisable); | |
| rhsc_enabled = 0; | |
| } | |
| hcd->poll_rh = 1; | |
| /* carry out appropriate state changes */ | |
| switch (ohci->hc_control & OHCI_CTRL_HCFS) { | |
| case OHCI_USB_OPER: | |
| /* keep on polling until we know a device is connected | |
| * and RHSC is enabled */ | |
| if (!ohci->autostop) { | |
| if (any_connected) { | |
| if (rhsc_enabled) | |
| hcd->poll_rh = 0; | |
| } else { | |
| ohci->autostop = 1; | |
| ohci->next_statechange = jiffies + HZ; | |
| } | |
| /* if no devices have been attached for one second, autostop */ | |
| } else { | |
| if (changed || any_connected) { | |
| ohci->autostop = 0; | |
| ohci->next_statechange = jiffies + | |
| STATECHANGE_DELAY; | |
| } else if (device_may_wakeup(&hcd->self.root_hub->dev) | |
| && time_after_eq(jiffies, | |
| ohci->next_statechange) | |
| && !ohci->ed_rm_list | |
| && !(ohci->hc_control & | |
| OHCI_SCHED_ENABLES)) { | |
| ohci_rh_suspend (ohci, 1); | |
| } | |
| } | |
| break; | |
| /* if there is a port change, autostart or ask to be resumed */ | |
| case OHCI_USB_SUSPEND: | |
| case OHCI_USB_RESUME: | |
| if (changed) { | |
| if (ohci->autostop) | |
| ohci_rh_resume (ohci); | |
| else | |
| usb_hcd_resume_root_hub (hcd); | |
| } else { | |
| /* everything is idle, no need for polling */ | |
| hcd->poll_rh = 0; | |
| } | |
| break; | |
| } | |
| done: | |
| spin_unlock_irqrestore (&ohci->lock, flags); | |
| return changed ? length : 0; | |
| } | |
| /*-------------------------------------------------------------------------*/ | |
| static void | |
| ohci_hub_descriptor ( | |
| struct ohci_hcd *ohci, | |
| struct usb_hub_descriptor *desc | |
| ) { | |
| u32 rh = roothub_a (ohci); | |
| u16 temp; | |
| desc->bDescriptorType = 0x29; | |
| desc->bPwrOn2PwrGood = (rh & RH_A_POTPGT) >> 24; | |
| desc->bHubContrCurrent = 0; | |
| desc->bNbrPorts = ohci->num_ports; | |
| temp = 1 + (ohci->num_ports / 8); | |
| desc->bDescLength = 7 + 2 * temp; | |
| temp = 0; | |
| if (rh & RH_A_NPS) /* no power switching? */ | |
| temp |= 0x0002; | |
| if (rh & RH_A_PSM) /* per-port power switching? */ | |
| temp |= 0x0001; | |
| if (rh & RH_A_NOCP) /* no overcurrent reporting? */ | |
| temp |= 0x0010; | |
| else if (rh & RH_A_OCPM) /* per-port overcurrent reporting? */ | |
| temp |= 0x0008; | |
| desc->wHubCharacteristics = (__force __u16)cpu_to_hc16(ohci, temp); | |
| /* two bitmaps: ports removable, and usb 1.0 legacy PortPwrCtrlMask */ | |
| rh = roothub_b (ohci); | |
| memset(desc->bitmap, 0xff, sizeof(desc->bitmap)); | |
| desc->bitmap [0] = rh & RH_B_DR; | |
| if (ohci->num_ports > 7) { | |
| desc->bitmap [1] = (rh & RH_B_DR) >> 8; | |
| desc->bitmap [2] = 0xff; | |
| } else | |
| desc->bitmap [1] = 0xff; | |
| } | |
| /*-------------------------------------------------------------------------*/ | |
| #ifdef CONFIG_USB_OTG | |
| static int ohci_start_port_reset (struct usb_hcd *hcd, unsigned port) | |
| { | |
| struct ohci_hcd *ohci = hcd_to_ohci (hcd); | |
| u32 status; | |
| if (!port) | |
| return -EINVAL; | |
| port--; | |
| /* start port reset before HNP protocol times out */ | |
| status = ohci_readl(ohci, &ohci->regs->roothub.portstatus [port]); | |
| if (!(status & RH_PS_CCS)) | |
| return -ENODEV; | |
| /* khubd will finish the reset later */ | |
| ohci_writel(ohci, RH_PS_PRS, &ohci->regs->roothub.portstatus [port]); | |
| return 0; | |
| } | |
| static void start_hnp(struct ohci_hcd *ohci); | |
| #else | |
| #define ohci_start_port_reset NULL | |
| #endif | |
| /*-------------------------------------------------------------------------*/ | |
| /* See usb 7.1.7.5: root hubs must issue at least 50 msec reset signaling, | |
| * not necessarily continuous ... to guard against resume signaling. | |
| * The short timeout is safe for non-root hubs, and is backward-compatible | |
| * with earlier Linux hosts. | |
| */ | |
| #ifdef CONFIG_USB_SUSPEND | |
| #define PORT_RESET_MSEC 50 | |
| #else | |
| #define PORT_RESET_MSEC 10 | |
| #endif | |
| /* this timer value might be vendor-specific ... */ | |
| #define PORT_RESET_HW_MSEC 10 | |
| /* wrap-aware logic morphed from <linux/jiffies.h> */ | |
| #define tick_before(t1,t2) ((s16)(((s16)(t1))-((s16)(t2))) < 0) | |
| /* called from some task, normally khubd */ | |
| static inline void root_port_reset (struct ohci_hcd *ohci, unsigned port) | |
| { | |
| __hc32 __iomem *portstat = &ohci->regs->roothub.portstatus [port]; | |
| u32 temp; | |
| u16 now = ohci_readl(ohci, &ohci->regs->fmnumber); | |
| u16 reset_done = now + PORT_RESET_MSEC; | |
| /* build a "continuous enough" reset signal, with up to | |
| * 3msec gap between pulses. scheduler HZ==100 must work; | |
| * this might need to be deadline-scheduled. | |
| */ | |
| do { | |
| /* spin until any current reset finishes */ | |
| for (;;) { | |
| temp = ohci_readl (ohci, portstat); | |
| if (!(temp & RH_PS_PRS)) | |
| break; | |
| udelay (500); | |
| } | |
| if (!(temp & RH_PS_CCS)) | |
| break; | |
| if (temp & RH_PS_PRSC) | |
| ohci_writel (ohci, RH_PS_PRSC, portstat); | |
| /* start the next reset, sleep till it's probably done */ | |
| ohci_writel (ohci, RH_PS_PRS, portstat); | |
| msleep(PORT_RESET_HW_MSEC); | |
| now = ohci_readl(ohci, &ohci->regs->fmnumber); | |
| } while (tick_before(now, reset_done)); | |
| /* caller synchronizes using PRSC */ | |
| } | |
| static int ohci_hub_control ( | |
| struct usb_hcd *hcd, | |
| u16 typeReq, | |
| u16 wValue, | |
| u16 wIndex, | |
| char *buf, | |
| u16 wLength | |
| ) { | |
| struct ohci_hcd *ohci = hcd_to_ohci (hcd); | |
| int ports = hcd_to_bus (hcd)->root_hub->maxchild; | |
| u32 temp; | |
| int retval = 0; | |
| if (unlikely(!test_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags))) | |
| return -ESHUTDOWN; | |
| switch (typeReq) { | |
| case ClearHubFeature: | |
| switch (wValue) { | |
| case C_HUB_OVER_CURRENT: | |
| ohci_writel (ohci, RH_HS_OCIC, | |
| &ohci->regs->roothub.status); | |
| case C_HUB_LOCAL_POWER: | |
| break; | |
| default: | |
| goto error; | |
| } | |
| break; | |
| case ClearPortFeature: | |
| if (!wIndex || wIndex > ports) | |
| goto error; | |
| wIndex--; | |
| switch (wValue) { | |
| case USB_PORT_FEAT_ENABLE: | |
| temp = RH_PS_CCS; | |
| break; | |
| case USB_PORT_FEAT_C_ENABLE: | |
| temp = RH_PS_PESC; | |
| break; | |
| case USB_PORT_FEAT_SUSPEND: | |
| temp = RH_PS_POCI; | |
| break; | |
| case USB_PORT_FEAT_C_SUSPEND: | |
| temp = RH_PS_PSSC; | |
| break; | |
| case USB_PORT_FEAT_POWER: | |
| temp = RH_PS_LSDA; | |
| break; | |
| case USB_PORT_FEAT_C_CONNECTION: | |
| temp = RH_PS_CSC; | |
| break; | |
| case USB_PORT_FEAT_C_OVER_CURRENT: | |
| temp = RH_PS_OCIC; | |
| break; | |
| case USB_PORT_FEAT_C_RESET: | |
| temp = RH_PS_PRSC; | |
| break; | |
| default: | |
| goto error; | |
| } | |
| ohci_writel (ohci, temp, | |
| &ohci->regs->roothub.portstatus [wIndex]); | |
| // ohci_readl (ohci, &ohci->regs->roothub.portstatus [wIndex]); | |
| break; | |
| case GetHubDescriptor: | |
| ohci_hub_descriptor (ohci, (struct usb_hub_descriptor *) buf); | |
| break; | |
| case GetHubStatus: | |
| temp = roothub_status (ohci) & ~(RH_HS_CRWE | RH_HS_DRWE); | |
| put_unaligned(cpu_to_le32 (temp), (__le32 *) buf); | |
| break; | |
| case GetPortStatus: | |
| if (!wIndex || wIndex > ports) | |
| goto error; | |
| wIndex--; | |
| temp = roothub_portstatus (ohci, wIndex); | |
| put_unaligned(cpu_to_le32 (temp), (__le32 *) buf); | |
| #ifndef OHCI_VERBOSE_DEBUG | |
| if (*(u16*)(buf+2)) /* only if wPortChange is interesting */ | |
| #endif | |
| dbg_port (ohci, "GetStatus", wIndex, temp); | |
| break; | |
| case SetHubFeature: | |
| switch (wValue) { | |
| case C_HUB_OVER_CURRENT: | |
| // FIXME: this can be cleared, yes? | |
| case C_HUB_LOCAL_POWER: | |
| break; | |
| default: | |
| goto error; | |
| } | |
| break; | |
| case SetPortFeature: | |
| if (!wIndex || wIndex > ports) | |
| goto error; | |
| wIndex--; | |
| switch (wValue) { | |
| case USB_PORT_FEAT_SUSPEND: | |
| #ifdef CONFIG_USB_OTG | |
| if (hcd->self.otg_port == (wIndex + 1) | |
| && hcd->self.b_hnp_enable) | |
| start_hnp(ohci); | |
| else | |
| #endif | |
| ohci_writel (ohci, RH_PS_PSS, | |
| &ohci->regs->roothub.portstatus [wIndex]); | |
| break; | |
| case USB_PORT_FEAT_POWER: | |
| ohci_writel (ohci, RH_PS_PPS, | |
| &ohci->regs->roothub.portstatus [wIndex]); | |
| break; | |
| case USB_PORT_FEAT_RESET: | |
| root_port_reset (ohci, wIndex); | |
| break; | |
| default: | |
| goto error; | |
| } | |
| break; | |
| default: | |
| error: | |
| /* "protocol stall" on error */ | |
| retval = -EPIPE; | |
| } | |
| return retval; | |
| } | |