| /* | |
| * include/asm-arm/arch-ixp4xx/platform.h | |
| * | |
| * Constants and functions that are useful to IXP4xx platform-specific code | |
| * and device drivers. | |
| * | |
| * Copyright (C) 2004 MontaVista Software, Inc. | |
| */ | |
| #ifndef __ASM_ARCH_HARDWARE_H__ | |
| #error "Do not include this directly, instead #include <asm/hardware.h>" | |
| #endif | |
| #ifndef __ASSEMBLY__ | |
| #include <asm/types.h> | |
| #ifndef __ARMEB__ | |
| #define REG_OFFSET 0 | |
| #else | |
| #define REG_OFFSET 3 | |
| #endif | |
| /* | |
| * Expansion bus memory regions | |
| */ | |
| #define IXP4XX_EXP_BUS_BASE_PHYS (0x50000000) | |
| /* | |
| * The expansion bus on the IXP4xx can be configured for either 16 or | |
| * 32MB windows and the CS offset for each region changes based on the | |
| * current configuration. This means that we cannot simply hardcode | |
| * each offset. ixp4xx_sys_init() looks at the expansion bus configuration | |
| * as setup by the bootloader to determine our window size. | |
| */ | |
| extern unsigned long ixp4xx_exp_bus_size; | |
| #define IXP4XX_EXP_BUS_BASE(region)\ | |
| (IXP4XX_EXP_BUS_BASE_PHYS + ((region) * ixp4xx_exp_bus_size)) | |
| #define IXP4XX_EXP_BUS_END(region)\ | |
| (IXP4XX_EXP_BUS_BASE(region) + ixp4xx_exp_bus_size - 1) | |
| /* Those macros can be used to adjust timing and configure | |
| * other features for each region. | |
| */ | |
| #define IXP4XX_EXP_BUS_RECOVERY_T(x) (((x) & 0x0f) << 16) | |
| #define IXP4XX_EXP_BUS_HOLD_T(x) (((x) & 0x03) << 20) | |
| #define IXP4XX_EXP_BUS_STROBE_T(x) (((x) & 0x0f) << 22) | |
| #define IXP4XX_EXP_BUS_SETUP_T(x) (((x) & 0x03) << 26) | |
| #define IXP4XX_EXP_BUS_ADDR_T(x) (((x) & 0x03) << 28) | |
| #define IXP4XX_EXP_BUS_SIZE(x) (((x) & 0x0f) << 10) | |
| #define IXP4XX_EXP_BUS_CYCLES(x) (((x) & 0x03) << 14) | |
| #define IXP4XX_EXP_BUS_CS_EN (1L << 31) | |
| #define IXP4XX_EXP_BUS_BYTE_RD16 (1L << 6) | |
| #define IXP4XX_EXP_BUS_HRDY_POL (1L << 5) | |
| #define IXP4XX_EXP_BUS_MUX_EN (1L << 4) | |
| #define IXP4XX_EXP_BUS_SPLT_EN (1L << 3) | |
| #define IXP4XX_EXP_BUS_WR_EN (1L << 1) | |
| #define IXP4XX_EXP_BUS_BYTE_EN (1L << 0) | |
| #define IXP4XX_EXP_BUS_CYCLES_INTEL 0x00 | |
| #define IXP4XX_EXP_BUS_CYCLES_MOTOROLA 0x01 | |
| #define IXP4XX_EXP_BUS_CYCLES_HPI 0x02 | |
| #define IXP4XX_FLASH_WRITABLE (0x2) | |
| #define IXP4XX_FLASH_DEFAULT (0xbcd23c40) | |
| #define IXP4XX_FLASH_WRITE (0xbcd23c42) | |
| /* | |
| * Clock Speed Definitions. | |
| */ | |
| #define IXP4XX_PERIPHERAL_BUS_CLOCK (66) /* 66Mhzi APB BUS */ | |
| #define IXP4XX_UART_XTAL 14745600 | |
| /* | |
| * The IXP4xx chips do not have an I2C unit, so GPIO lines are just | |
| * used to | |
| * Used as platform_data to provide GPIO pin information to the ixp42x | |
| * I2C driver. | |
| */ | |
| struct ixp4xx_i2c_pins { | |
| unsigned long sda_pin; | |
| unsigned long scl_pin; | |
| }; | |
| struct sys_timer; | |
| /* | |
| * Frequency of clock used for primary clocksource | |
| */ | |
| extern unsigned long ixp4xx_timer_freq; | |
| /* | |
| * Functions used by platform-level setup code | |
| */ | |
| extern void ixp4xx_map_io(void); | |
| extern void ixp4xx_init_irq(void); | |
| extern void ixp4xx_sys_init(void); | |
| extern struct sys_timer ixp4xx_timer; | |
| extern void ixp4xx_pci_preinit(void); | |
| struct pci_sys_data; | |
| extern int ixp4xx_setup(int nr, struct pci_sys_data *sys); | |
| extern struct pci_bus *ixp4xx_scan_bus(int nr, struct pci_sys_data *sys); | |
| /* | |
| * GPIO-functions | |
| */ | |
| /* | |
| * The following converted to the real HW bits the gpio_line_config | |
| */ | |
| /* GPIO pin types */ | |
| #define IXP4XX_GPIO_OUT 0x1 | |
| #define IXP4XX_GPIO_IN 0x2 | |
| /* GPIO signal types */ | |
| #define IXP4XX_GPIO_LOW 0 | |
| #define IXP4XX_GPIO_HIGH 1 | |
| /* GPIO Clocks */ | |
| #define IXP4XX_GPIO_CLK_0 14 | |
| #define IXP4XX_GPIO_CLK_1 15 | |
| static inline void gpio_line_config(u8 line, u32 direction) | |
| { | |
| if (direction == IXP4XX_GPIO_IN) | |
| *IXP4XX_GPIO_GPOER |= (1 << line); | |
| else | |
| *IXP4XX_GPIO_GPOER &= ~(1 << line); | |
| } | |
| static inline void gpio_line_get(u8 line, int *value) | |
| { | |
| *value = (*IXP4XX_GPIO_GPINR >> line) & 0x1; | |
| } | |
| static inline void gpio_line_set(u8 line, int value) | |
| { | |
| if (value == IXP4XX_GPIO_HIGH) | |
| *IXP4XX_GPIO_GPOUTR |= (1 << line); | |
| else if (value == IXP4XX_GPIO_LOW) | |
| *IXP4XX_GPIO_GPOUTR &= ~(1 << line); | |
| } | |
| #endif // __ASSEMBLY__ | |