| /* | |
| * linux/include/asm-arm/arch-sa1100/simpad.h | |
| * | |
| * based of assabet.h same as HUW_Webpanel | |
| * | |
| * This file contains the hardware specific definitions for SIMpad | |
| * | |
| * 2001/05/14 Juergen Messerer <juergen.messerer@freesurf.ch> | |
| */ | |
| #ifndef __ASM_ARCH_SIMPAD_H | |
| #define __ASM_ARCH_SIMPAD_H | |
| #define GPIO_UART1_RTS GPIO_GPIO14 | |
| #define GPIO_UART1_DTR GPIO_GPIO7 | |
| #define GPIO_UART1_CTS GPIO_GPIO8 | |
| #define GPIO_UART1_DCD GPIO_GPIO23 | |
| #define GPIO_UART1_DSR GPIO_GPIO6 | |
| #define GPIO_UART3_RTS GPIO_GPIO12 | |
| #define GPIO_UART3_DTR GPIO_GPIO16 | |
| #define GPIO_UART3_CTS GPIO_GPIO13 | |
| #define GPIO_UART3_DCD GPIO_GPIO18 | |
| #define GPIO_UART3_DSR GPIO_GPIO17 | |
| #define GPIO_POWER_BUTTON GPIO_GPIO0 | |
| #define GPIO_UCB1300_IRQ GPIO_GPIO22 /* UCB GPIO and touchscreen */ | |
| #define IRQ_UART1_CTS IRQ_GPIO15 | |
| #define IRQ_UART1_DCD GPIO_GPIO23 | |
| #define IRQ_UART1_DSR GPIO_GPIO6 | |
| #define IRQ_UART3_CTS GPIO_GPIO13 | |
| #define IRQ_UART3_DCD GPIO_GPIO18 | |
| #define IRQ_UART3_DSR GPIO_GPIO17 | |
| #define IRQ_GPIO_UCB1300_IRQ IRQ_GPIO22 | |
| #define IRQ_GPIO_POWER_BUTTON IRQ_GPIO0 | |
| /*--- PCMCIA ---*/ | |
| #define GPIO_CF_CD GPIO_GPIO24 | |
| #define GPIO_CF_IRQ GPIO_GPIO1 | |
| #define IRQ_GPIO_CF_IRQ IRQ_GPIO1 | |
| #define IRQ_GPIO_CF_CD IRQ_GPIO24 | |
| /*--- SmartCard ---*/ | |
| #define GPIO_SMART_CARD GPIO_GPIO10 | |
| #define IRQ_GPIO_SMARD_CARD IRQ_GPIO10 | |
| // CS3 Latch is write only, a shadow is necessary | |
| #define CS3BUSTYPE unsigned volatile long | |
| #define CS3_BASE 0xf1000000 | |
| #define VCC_5V_EN 0x0001 // For 5V PCMCIA | |
| #define VCC_3V_EN 0x0002 // FOR 3.3V PCMCIA | |
| #define EN1 0x0004 // This is only for EPROM's | |
| #define EN0 0x0008 // Both should be enable for 3.3V or 5V | |
| #define DISPLAY_ON 0x0010 | |
| #define PCMCIA_BUFF_DIS 0x0020 | |
| #define MQ_RESET 0x0040 | |
| #define PCMCIA_RESET 0x0080 | |
| #define DECT_POWER_ON 0x0100 | |
| #define IRDA_SD 0x0200 // Shutdown for powersave | |
| #define RS232_ON 0x0400 | |
| #define SD_MEDIAQ 0x0800 // Shutdown for powersave | |
| #define LED2_ON 0x1000 | |
| #define IRDA_MODE 0x2000 // Fast/Slow IrDA mode | |
| #define ENABLE_5V 0x4000 // Enable 5V circuit | |
| #define RESET_SIMCARD 0x8000 | |
| #define RS232_ENABLE 0x0440 | |
| #define PCMCIAMASK 0x402f | |
| struct simpad_battery { | |
| unsigned char ac_status; /* line connected yes/no */ | |
| unsigned char status; /* battery loading yes/no */ | |
| unsigned char percentage; /* percentage loaded */ | |
| unsigned short life; /* life till empty */ | |
| }; | |
| /* These should match the apm_bios.h definitions */ | |
| #define SIMPAD_AC_STATUS_AC_OFFLINE 0x00 | |
| #define SIMPAD_AC_STATUS_AC_ONLINE 0x01 | |
| #define SIMPAD_AC_STATUS_AC_BACKUP 0x02 /* What does this mean? */ | |
| #define SIMPAD_AC_STATUS_AC_UNKNOWN 0xff | |
| /* These bitfields are rarely "or'd" together */ | |
| #define SIMPAD_BATT_STATUS_HIGH 0x01 | |
| #define SIMPAD_BATT_STATUS_LOW 0x02 | |
| #define SIMPAD_BATT_STATUS_CRITICAL 0x04 | |
| #define SIMPAD_BATT_STATUS_CHARGING 0x08 | |
| #define SIMPAD_BATT_STATUS_CHARGE_MAIN 0x10 | |
| #define SIMPAD_BATT_STATUS_DEAD 0x20 /* Battery will not charge */ | |
| #define SIMPAD_BATT_NOT_INSTALLED 0x20 /* For expansion pack batteries */ | |
| #define SIMPAD_BATT_STATUS_FULL 0x40 /* Battery fully charged (and connected to AC) */ | |
| #define SIMPAD_BATT_STATUS_NOBATT 0x80 | |
| #define SIMPAD_BATT_STATUS_UNKNOWN 0xff | |
| extern int simpad_get_battery(struct simpad_battery* ); | |
| #endif // __ASM_ARCH_SIMPAD_H | |