| /* | |
| * sound/oss/pss.c | |
| * | |
| * The low level driver for the Personal Sound System (ECHO ESC614). | |
| * | |
| * | |
| * Copyright (C) by Hannu Savolainen 1993-1997 | |
| * | |
| * OSS/Free for Linux is distributed under the GNU GENERAL PUBLIC LICENSE (GPL) | |
| * Version 2 (June 1991). See the "COPYING" file distributed with this software | |
| * for more info. | |
| * | |
| * | |
| * Thomas Sailer ioctl code reworked (vmalloc/vfree removed) | |
| * Alan Cox modularisation, clean up. | |
| * | |
| * 98-02-21: Vladimir Michl <vladimir.michl@upol.cz> | |
| * Added mixer device for Beethoven ADSP-16 (master volume, | |
| * bass, treble, synth), only for speakers. | |
| * Fixed bug in pss_write (exchange parameters) | |
| * Fixed config port of SB | |
| * Requested two regions for PSS (PSS mixer, PSS config) | |
| * Modified pss_download_boot | |
| * To probe_pss_mss added test for initialize AD1848 | |
| * 98-05-28: Vladimir Michl <vladimir.michl@upol.cz> | |
| * Fixed computation of mixer volumes | |
| * 04-05-1999: Anthony Barbachan <barbcode@xmen.cis.fordham.edu> | |
| * Added code that allows the user to enable his cdrom and/or | |
| * joystick through the module parameters pss_cdrom_port and | |
| * pss_enable_joystick. pss_cdrom_port takes a port address as its | |
| * argument. pss_enable_joystick takes either a 0 or a non-0 as its | |
| * argument. | |
| * 04-06-1999: Anthony Barbachan <barbcode@xmen.cis.fordham.edu> | |
| * Separated some code into new functions for easier reuse. | |
| * Cleaned up and streamlined new code. Added code to allow a user | |
| * to only use this driver for enabling non-sound components | |
| * through the new module parameter pss_no_sound (flag). Added | |
| * code that would allow a user to decide whether the driver should | |
| * reset the configured hardware settings for the PSS board through | |
| * the module parameter pss_keep_settings (flag). This flag will | |
| * allow a user to free up resources in use by this card if needbe, | |
| * furthermore it allows him to use this driver to just enable the | |
| * emulations and then be unloaded as it is no longer needed. Both | |
| * new settings are only available to this driver if compiled as a | |
| * module. The default settings of all new parameters are set to | |
| * load the driver as it did in previous versions. | |
| * 04-07-1999: Anthony Barbachan <barbcode@xmen.cis.fordham.edu> | |
| * Added module parameter pss_firmware to allow the user to tell | |
| * the driver where the fireware file is located. The default | |
| * setting is the previous hardcoded setting "/etc/sound/pss_synth". | |
| * 00-03-03: Christoph Hellwig <chhellwig@infradead.org> | |
| * Adapted to module_init/module_exit | |
| * 11-10-2000: Bartlomiej Zolnierkiewicz <bkz@linux-ide.org> | |
| * Added __init to probe_pss(), attach_pss() and probe_pss_mpu() | |
| * 02-Jan-2001: Chris Rankin | |
| * Specify that this module owns the coprocessor | |
| */ | |
| #include <linux/init.h> | |
| #include <linux/module.h> | |
| #include <linux/spinlock.h> | |
| #include "sound_config.h" | |
| #include "sound_firmware.h" | |
| #include "ad1848.h" | |
| #include "mpu401.h" | |
| /* | |
| * PSS registers. | |
| */ | |
| #define REG(x) (devc->base+x) | |
| #define PSS_DATA 0 | |
| #define PSS_STATUS 2 | |
| #define PSS_CONTROL 2 | |
| #define PSS_ID 4 | |
| #define PSS_IRQACK 4 | |
| #define PSS_PIO 0x1a | |
| /* | |
| * Config registers | |
| */ | |
| #define CONF_PSS 0x10 | |
| #define CONF_WSS 0x12 | |
| #define CONF_SB 0x14 | |
| #define CONF_CDROM 0x16 | |
| #define CONF_MIDI 0x18 | |
| /* | |
| * Status bits. | |
| */ | |
| #define PSS_FLAG3 0x0800 | |
| #define PSS_FLAG2 0x0400 | |
| #define PSS_FLAG1 0x1000 | |
| #define PSS_FLAG0 0x0800 | |
| #define PSS_WRITE_EMPTY 0x8000 | |
| #define PSS_READ_FULL 0x4000 | |
| /* | |
| * WSS registers | |
| */ | |
| #define WSS_INDEX 4 | |
| #define WSS_DATA 5 | |
| /* | |
| * WSS status bits | |
| */ | |
| #define WSS_INITIALIZING 0x80 | |
| #define WSS_AUTOCALIBRATION 0x20 | |
| #define NO_WSS_MIXER -1 | |
| #include "coproc.h" | |
| #include "pss_boot.h" | |
| /* If compiled into kernel, it enable or disable pss mixer */ | |
| #ifdef CONFIG_PSS_MIXER | |
| static int pss_mixer = 1; | |
| #else | |
| static int pss_mixer; | |
| #endif | |
| typedef struct pss_mixerdata { | |
| unsigned int volume_l; | |
| unsigned int volume_r; | |
| unsigned int bass; | |
| unsigned int treble; | |
| unsigned int synth; | |
| } pss_mixerdata; | |
| typedef struct pss_confdata { | |
| int base; | |
| int irq; | |
| int dma; | |
| int *osp; | |
| pss_mixerdata mixer; | |
| int ad_mixer_dev; | |
| } pss_confdata; | |
| static pss_confdata pss_data; | |
| static pss_confdata *devc = &pss_data; | |
| static DEFINE_SPINLOCK(lock); | |
| static int pss_initialized; | |
| static int nonstandard_microcode; | |
| static int pss_cdrom_port = -1; /* Parameter for the PSS cdrom port */ | |
| static int pss_enable_joystick; /* Parameter for enabling the joystick */ | |
| static coproc_operations pss_coproc_operations; | |
| static void pss_write(pss_confdata *devc, int data) | |
| { | |
| unsigned long i, limit; | |
| limit = jiffies + HZ/10; /* The timeout is 0.1 seconds */ | |
| /* | |
| * Note! the i<5000000 is an emergency exit. The dsp_command() is sometimes | |
| * called while interrupts are disabled. This means that the timer is | |
| * disabled also. However the timeout situation is a abnormal condition. | |
| * Normally the DSP should be ready to accept commands after just couple of | |
| * loops. | |
| */ | |
| for (i = 0; i < 5000000 && time_before(jiffies, limit); i++) | |
| { | |
| if (inw(REG(PSS_STATUS)) & PSS_WRITE_EMPTY) | |
| { | |
| outw(data, REG(PSS_DATA)); | |
| return; | |
| } | |
| } | |
| printk(KERN_WARNING "PSS: DSP Command (%04x) Timeout.\n", data); | |
| } | |
| static int __init probe_pss(struct address_info *hw_config) | |
| { | |
| unsigned short id; | |
| int irq, dma; | |
| devc->base = hw_config->io_base; | |
| irq = devc->irq = hw_config->irq; | |
| dma = devc->dma = hw_config->dma; | |
| devc->osp = hw_config->osp; | |
| if (devc->base != 0x220 && devc->base != 0x240) | |
| if (devc->base != 0x230 && devc->base != 0x250) /* Some cards use these */ | |
| return 0; | |
| if (!request_region(devc->base, 0x10, "PSS mixer, SB emulation")) { | |
| printk(KERN_ERR "PSS: I/O port conflict\n"); | |
| return 0; | |
| } | |
| id = inw(REG(PSS_ID)); | |
| if ((id >> 8) != 'E') { | |
| printk(KERN_ERR "No PSS signature detected at 0x%x (0x%x)\n", devc->base, id); | |
| release_region(devc->base, 0x10); | |
| return 0; | |
| } | |
| if (!request_region(devc->base + 0x10, 0x9, "PSS config")) { | |
| printk(KERN_ERR "PSS: I/O port conflict\n"); | |
| release_region(devc->base, 0x10); | |
| return 0; | |
| } | |
| return 1; | |
| } | |
| static int set_irq(pss_confdata * devc, int dev, int irq) | |
| { | |
| static unsigned short irq_bits[16] = | |
| { | |
| 0x0000, 0x0000, 0x0000, 0x0008, | |
| 0x0000, 0x0010, 0x0000, 0x0018, | |
| 0x0000, 0x0020, 0x0028, 0x0030, | |
| 0x0038, 0x0000, 0x0000, 0x0000 | |
| }; | |
| unsigned short tmp, bits; | |
| if (irq < 0 || irq > 15) | |
| return 0; | |
| tmp = inw(REG(dev)) & ~0x38; /* Load confreg, mask IRQ bits out */ | |
| if ((bits = irq_bits[irq]) == 0 && irq != 0) | |
| { | |
| printk(KERN_ERR "PSS: Invalid IRQ %d\n", irq); | |
| return 0; | |
| } | |
| outw(tmp | bits, REG(dev)); | |
| return 1; | |
| } | |
| static int set_io_base(pss_confdata * devc, int dev, int base) | |
| { | |
| unsigned short tmp = inw(REG(dev)) & 0x003f; | |
| unsigned short bits = (base & 0x0ffc) << 4; | |
| outw(bits | tmp, REG(dev)); | |
| return 1; | |
| } | |
| static int set_dma(pss_confdata * devc, int dev, int dma) | |
| { | |
| static unsigned short dma_bits[8] = | |
| { | |
| 0x0001, 0x0002, 0x0000, 0x0003, | |
| 0x0000, 0x0005, 0x0006, 0x0007 | |
| }; | |
| unsigned short tmp, bits; | |
| if (dma < 0 || dma > 7) | |
| return 0; | |
| tmp = inw(REG(dev)) & ~0x07; /* Load confreg, mask DMA bits out */ | |
| if ((bits = dma_bits[dma]) == 0 && dma != 4) | |
| { | |
| printk(KERN_ERR "PSS: Invalid DMA %d\n", dma); | |
| return 0; | |
| } | |
| outw(tmp | bits, REG(dev)); | |
| return 1; | |
| } | |
| static int pss_reset_dsp(pss_confdata * devc) | |
| { | |
| unsigned long i, limit = jiffies + HZ/10; | |
| outw(0x2000, REG(PSS_CONTROL)); | |
| for (i = 0; i < 32768 && (limit-jiffies >= 0); i++) | |
| inw(REG(PSS_CONTROL)); | |
| outw(0x0000, REG(PSS_CONTROL)); | |
| return 1; | |
| } | |
| static int pss_put_dspword(pss_confdata * devc, unsigned short word) | |
| { | |
| int i, val; | |
| for (i = 0; i < 327680; i++) | |
| { | |
| val = inw(REG(PSS_STATUS)); | |
| if (val & PSS_WRITE_EMPTY) | |
| { | |
| outw(word, REG(PSS_DATA)); | |
| return 1; | |
| } | |
| } | |
| return 0; | |
| } | |
| static int pss_get_dspword(pss_confdata * devc, unsigned short *word) | |
| { | |
| int i, val; | |
| for (i = 0; i < 327680; i++) | |
| { | |
| val = inw(REG(PSS_STATUS)); | |
| if (val & PSS_READ_FULL) | |
| { | |
| *word = inw(REG(PSS_DATA)); | |
| return 1; | |
| } | |
| } | |
| return 0; | |
| } | |
| static int pss_download_boot(pss_confdata * devc, unsigned char *block, int size, int flags) | |
| { | |
| int i, val, count; | |
| unsigned long limit; | |
| if (flags & CPF_FIRST) | |
| { | |
| /*_____ Warn DSP software that a boot is coming */ | |
| outw(0x00fe, REG(PSS_DATA)); | |
| limit = jiffies + HZ/10; | |
| for (i = 0; i < 32768 && time_before(jiffies, limit); i++) | |
| if (inw(REG(PSS_DATA)) == 0x5500) | |
| break; | |
| outw(*block++, REG(PSS_DATA)); | |
| pss_reset_dsp(devc); | |
| } | |
| count = 1; | |
| while ((flags&CPF_LAST) || count<size ) | |
| { | |
| int j; | |
| for (j = 0; j < 327670; j++) | |
| { | |
| /*_____ Wait for BG to appear */ | |
| if (inw(REG(PSS_STATUS)) & PSS_FLAG3) | |
| break; | |
| } | |
| if (j == 327670) | |
| { | |
| /* It's ok we timed out when the file was empty */ | |
| if (count >= size && flags & CPF_LAST) | |
| break; | |
| else | |
| { | |
| printk("\n"); | |
| printk(KERN_ERR "PSS: Download timeout problems, byte %d=%d\n", count, size); | |
| return 0; | |
| } | |
| } | |
| /*_____ Send the next byte */ | |
| if (count >= size) | |
| { | |
| /* If not data in block send 0xffff */ | |
| outw (0xffff, REG (PSS_DATA)); | |
| } | |
| else | |
| { | |
| /*_____ Send the next byte */ | |
| outw (*block++, REG (PSS_DATA)); | |
| }; | |
| count++; | |
| } | |
| if (flags & CPF_LAST) | |
| { | |
| /*_____ Why */ | |
| outw(0, REG(PSS_DATA)); | |
| limit = jiffies + HZ/10; | |
| for (i = 0; i < 32768 && (limit - jiffies >= 0); i++) | |
| val = inw(REG(PSS_STATUS)); | |
| limit = jiffies + HZ/10; | |
| for (i = 0; i < 32768 && (limit-jiffies >= 0); i++) | |
| { | |
| val = inw(REG(PSS_STATUS)); | |
| if (val & 0x4000) | |
| break; | |
| } | |
| /* now read the version */ | |
| for (i = 0; i < 32000; i++) | |
| { | |
| val = inw(REG(PSS_STATUS)); | |
| if (val & PSS_READ_FULL) | |
| break; | |
| } | |
| if (i == 32000) | |
| return 0; | |
| val = inw(REG(PSS_DATA)); | |
| /* printk( "<PSS: microcode version %d.%d loaded>", val/16, val % 16); */ | |
| } | |
| return 1; | |
| } | |
| /* Mixer */ | |
| static void set_master_volume(pss_confdata *devc, int left, int right) | |
| { | |
| static unsigned char log_scale[101] = { | |
| 0xdb, 0xe0, 0xe3, 0xe5, 0xe7, 0xe9, 0xea, 0xeb, 0xec, 0xed, 0xed, 0xee, | |
| 0xef, 0xef, 0xf0, 0xf0, 0xf1, 0xf1, 0xf2, 0xf2, 0xf2, 0xf3, 0xf3, 0xf3, | |
| 0xf4, 0xf4, 0xf4, 0xf5, 0xf5, 0xf5, 0xf5, 0xf6, 0xf6, 0xf6, 0xf6, 0xf7, | |
| 0xf7, 0xf7, 0xf7, 0xf7, 0xf8, 0xf8, 0xf8, 0xf8, 0xf8, 0xf9, 0xf9, 0xf9, | |
| 0xf9, 0xf9, 0xf9, 0xfa, 0xfa, 0xfa, 0xfa, 0xfa, 0xfa, 0xfa, 0xfb, 0xfb, | |
| 0xfb, 0xfb, 0xfb, 0xfb, 0xfb, 0xfb, 0xfc, 0xfc, 0xfc, 0xfc, 0xfc, 0xfc, | |
| 0xfc, 0xfc, 0xfc, 0xfc, 0xfd, 0xfd, 0xfd, 0xfd, 0xfd, 0xfd, 0xfd, 0xfd, | |
| 0xfd, 0xfd, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, 0xfe, | |
| 0xfe, 0xfe, 0xff, 0xff, 0xff | |
| }; | |
| pss_write(devc, 0x0010); | |
| pss_write(devc, log_scale[left] | 0x0000); | |
| pss_write(devc, 0x0010); | |
| pss_write(devc, log_scale[right] | 0x0100); | |
| } | |
| static void set_synth_volume(pss_confdata *devc, int volume) | |
| { | |
| int vol = ((0x8000*volume)/100L); | |
| pss_write(devc, 0x0080); | |
| pss_write(devc, vol); | |
| pss_write(devc, 0x0081); | |
| pss_write(devc, vol); | |
| } | |
| static void set_bass(pss_confdata *devc, int level) | |
| { | |
| int vol = (int)(((0xfd - 0xf0) * level)/100L) + 0xf0; | |
| pss_write(devc, 0x0010); | |
| pss_write(devc, vol | 0x0200); | |
| }; | |
| static void set_treble(pss_confdata *devc, int level) | |
| { | |
| int vol = (((0xfd - 0xf0) * level)/100L) + 0xf0; | |
| pss_write(devc, 0x0010); | |
| pss_write(devc, vol | 0x0300); | |
| }; | |
| static void pss_mixer_reset(pss_confdata *devc) | |
| { | |
| set_master_volume(devc, 33, 33); | |
| set_bass(devc, 50); | |
| set_treble(devc, 50); | |
| set_synth_volume(devc, 30); | |
| pss_write (devc, 0x0010); | |
| pss_write (devc, 0x0800 | 0xce); /* Stereo */ | |
| if(pss_mixer) | |
| { | |
| devc->mixer.volume_l = devc->mixer.volume_r = 33; | |
| devc->mixer.bass = 50; | |
| devc->mixer.treble = 50; | |
| devc->mixer.synth = 30; | |
| } | |
| } | |
| static int set_volume_mono(unsigned __user *p, int *aleft) | |
| { | |
| int left; | |
| unsigned volume; | |
| if (get_user(volume, p)) | |
| return -EFAULT; | |
| left = volume & 0xff; | |
| if (left > 100) | |
| left = 100; | |
| *aleft = left; | |
| return 0; | |
| } | |
| static int set_volume_stereo(unsigned __user *p, int *aleft, int *aright) | |
| { | |
| int left, right; | |
| unsigned volume; | |
| if (get_user(volume, p)) | |
| return -EFAULT; | |
| left = volume & 0xff; | |
| if (left > 100) | |
| left = 100; | |
| right = (volume >> 8) & 0xff; | |
| if (right > 100) | |
| right = 100; | |
| *aleft = left; | |
| *aright = right; | |
| return 0; | |
| } | |
| static int ret_vol_mono(int left) | |
| { | |
| return ((left << 8) | left); | |
| } | |
| static int ret_vol_stereo(int left, int right) | |
| { | |
| return ((right << 8) | left); | |
| } | |
| static int call_ad_mixer(pss_confdata *devc,unsigned int cmd, void __user *arg) | |
| { | |
| if (devc->ad_mixer_dev != NO_WSS_MIXER) | |
| return mixer_devs[devc->ad_mixer_dev]->ioctl(devc->ad_mixer_dev, cmd, arg); | |
| else | |
| return -EINVAL; | |
| } | |
| static int pss_mixer_ioctl (int dev, unsigned int cmd, void __user *arg) | |
| { | |
| pss_confdata *devc = mixer_devs[dev]->devc; | |
| int cmdf = cmd & 0xff; | |
| if ((cmdf != SOUND_MIXER_VOLUME) && (cmdf != SOUND_MIXER_BASS) && | |
| (cmdf != SOUND_MIXER_TREBLE) && (cmdf != SOUND_MIXER_SYNTH) && | |
| (cmdf != SOUND_MIXER_DEVMASK) && (cmdf != SOUND_MIXER_STEREODEVS) && | |
| (cmdf != SOUND_MIXER_RECMASK) && (cmdf != SOUND_MIXER_CAPS) && | |
| (cmdf != SOUND_MIXER_RECSRC)) | |
| { | |
| return call_ad_mixer(devc, cmd, arg); | |
| } | |
| if (((cmd >> 8) & 0xff) != 'M') | |
| return -EINVAL; | |
| if (_SIOC_DIR (cmd) & _SIOC_WRITE) | |
| { | |
| switch (cmdf) | |
| { | |
| case SOUND_MIXER_RECSRC: | |
| if (devc->ad_mixer_dev != NO_WSS_MIXER) | |
| return call_ad_mixer(devc, cmd, arg); | |
| else | |
| { | |
| int v; | |
| if (get_user(v, (int __user *)arg)) | |
| return -EFAULT; | |
| if (v != 0) | |
| return -EINVAL; | |
| return 0; | |
| } | |
| case SOUND_MIXER_VOLUME: | |
| if (set_volume_stereo(arg, | |
| &devc->mixer.volume_l, | |
| &devc->mixer.volume_r)) | |
| return -EFAULT; | |
| set_master_volume(devc, devc->mixer.volume_l, | |
| devc->mixer.volume_r); | |
| return ret_vol_stereo(devc->mixer.volume_l, | |
| devc->mixer.volume_r); | |
| case SOUND_MIXER_BASS: | |
| if (set_volume_mono(arg, &devc->mixer.bass)) | |
| return -EFAULT; | |
| set_bass(devc, devc->mixer.bass); | |
| return ret_vol_mono(devc->mixer.bass); | |
| case SOUND_MIXER_TREBLE: | |
| if (set_volume_mono(arg, &devc->mixer.treble)) | |
| return -EFAULT; | |
| set_treble(devc, devc->mixer.treble); | |
| return ret_vol_mono(devc->mixer.treble); | |
| case SOUND_MIXER_SYNTH: | |
| if (set_volume_mono(arg, &devc->mixer.synth)) | |
| return -EFAULT; | |
| set_synth_volume(devc, devc->mixer.synth); | |
| return ret_vol_mono(devc->mixer.synth); | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| else | |
| { | |
| int val, and_mask = 0, or_mask = 0; | |
| /* | |
| * Return parameters | |
| */ | |
| switch (cmdf) | |
| { | |
| case SOUND_MIXER_DEVMASK: | |
| if (call_ad_mixer(devc, cmd, arg) == -EINVAL) | |
| break; | |
| and_mask = ~0; | |
| or_mask = SOUND_MASK_VOLUME | SOUND_MASK_BASS | SOUND_MASK_TREBLE | SOUND_MASK_SYNTH; | |
| break; | |
| case SOUND_MIXER_STEREODEVS: | |
| if (call_ad_mixer(devc, cmd, arg) == -EINVAL) | |
| break; | |
| and_mask = ~0; | |
| or_mask = SOUND_MASK_VOLUME; | |
| break; | |
| case SOUND_MIXER_RECMASK: | |
| if (devc->ad_mixer_dev != NO_WSS_MIXER) | |
| return call_ad_mixer(devc, cmd, arg); | |
| break; | |
| case SOUND_MIXER_CAPS: | |
| if (devc->ad_mixer_dev != NO_WSS_MIXER) | |
| return call_ad_mixer(devc, cmd, arg); | |
| or_mask = SOUND_CAP_EXCL_INPUT; | |
| break; | |
| case SOUND_MIXER_RECSRC: | |
| if (devc->ad_mixer_dev != NO_WSS_MIXER) | |
| return call_ad_mixer(devc, cmd, arg); | |
| break; | |
| case SOUND_MIXER_VOLUME: | |
| or_mask = ret_vol_stereo(devc->mixer.volume_l, devc->mixer.volume_r); | |
| break; | |
| case SOUND_MIXER_BASS: | |
| or_mask = ret_vol_mono(devc->mixer.bass); | |
| break; | |
| case SOUND_MIXER_TREBLE: | |
| or_mask = ret_vol_mono(devc->mixer.treble); | |
| break; | |
| case SOUND_MIXER_SYNTH: | |
| or_mask = ret_vol_mono(devc->mixer.synth); | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| if (get_user(val, (int __user *)arg)) | |
| return -EFAULT; | |
| val &= and_mask; | |
| val |= or_mask; | |
| if (put_user(val, (int __user *)arg)) | |
| return -EFAULT; | |
| return val; | |
| } | |
| } | |
| static struct mixer_operations pss_mixer_operations = | |
| { | |
| .owner = THIS_MODULE, | |
| .id = "SOUNDPORT", | |
| .name = "PSS-AD1848", | |
| .ioctl = pss_mixer_ioctl | |
| }; | |
| static void disable_all_emulations(void) | |
| { | |
| outw(0x0000, REG(CONF_PSS)); /* 0x0400 enables joystick */ | |
| outw(0x0000, REG(CONF_WSS)); | |
| outw(0x0000, REG(CONF_SB)); | |
| outw(0x0000, REG(CONF_MIDI)); | |
| outw(0x0000, REG(CONF_CDROM)); | |
| } | |
| static void configure_nonsound_components(void) | |
| { | |
| /* Configure Joystick port */ | |
| if(pss_enable_joystick) | |
| { | |
| outw(0x0400, REG(CONF_PSS)); /* 0x0400 enables joystick */ | |
| printk(KERN_INFO "PSS: joystick enabled.\n"); | |
| } | |
| else | |
| { | |
| printk(KERN_INFO "PSS: joystick port not enabled.\n"); | |
| } | |
| /* Configure CDROM port */ | |
| if(pss_cdrom_port == -1) /* If cdrom port enablation wasn't requested */ | |
| { | |
| printk(KERN_INFO "PSS: CDROM port not enabled.\n"); | |
| } | |
| else if(check_region(pss_cdrom_port, 2)) | |
| { | |
| printk(KERN_ERR "PSS: CDROM I/O port conflict.\n"); | |
| } | |
| else if(!set_io_base(devc, CONF_CDROM, pss_cdrom_port)) | |
| { | |
| printk(KERN_ERR "PSS: CDROM I/O port could not be set.\n"); | |
| } | |
| else /* CDROM port successfully configured */ | |
| { | |
| printk(KERN_INFO "PSS: CDROM I/O port set to 0x%x.\n", pss_cdrom_port); | |
| } | |
| } | |
| static int __init attach_pss(struct address_info *hw_config) | |
| { | |
| unsigned short id; | |
| char tmp[100]; | |
| devc->base = hw_config->io_base; | |
| devc->irq = hw_config->irq; | |
| devc->dma = hw_config->dma; | |
| devc->osp = hw_config->osp; | |
| devc->ad_mixer_dev = NO_WSS_MIXER; | |
| if (!probe_pss(hw_config)) | |
| return 0; | |
| id = inw(REG(PSS_ID)) & 0x00ff; | |
| /* | |
| * Disable all emulations. Will be enabled later (if required). | |
| */ | |
| disable_all_emulations(); | |
| #ifdef YOU_REALLY_WANT_TO_ALLOCATE_THESE_RESOURCES | |
| if (sound_alloc_dma(hw_config->dma, "PSS")) | |
| { | |
| printk("pss.c: Can't allocate DMA channel.\n"); | |
| release_region(hw_config->io_base, 0x10); | |
| release_region(hw_config->io_base+0x10, 0x9); | |
| return 0; | |
| } | |
| if (!set_irq(devc, CONF_PSS, devc->irq)) | |
| { | |
| printk("PSS: IRQ allocation error.\n"); | |
| release_region(hw_config->io_base, 0x10); | |
| release_region(hw_config->io_base+0x10, 0x9); | |
| return 0; | |
| } | |
| if (!set_dma(devc, CONF_PSS, devc->dma)) | |
| { | |
| printk(KERN_ERR "PSS: DMA allocation error\n"); | |
| release_region(hw_config->io_base, 0x10); | |
| release_region(hw_config->io_base+0x10, 0x9); | |
| return 0; | |
| } | |
| #endif | |
| configure_nonsound_components(); | |
| pss_initialized = 1; | |
| sprintf(tmp, "ECHO-PSS Rev. %d", id); | |
| conf_printf(tmp, hw_config); | |
| return 1; | |
| } | |
| static int __init probe_pss_mpu(struct address_info *hw_config) | |
| { | |
| struct resource *ports; | |
| int timeout; | |
| if (!pss_initialized) | |
| return 0; | |
| ports = request_region(hw_config->io_base, 2, "mpu401"); | |
| if (!ports) { | |
| printk(KERN_ERR "PSS: MPU I/O port conflict\n"); | |
| return 0; | |
| } | |
| if (!set_io_base(devc, CONF_MIDI, hw_config->io_base)) { | |
| printk(KERN_ERR "PSS: MIDI base could not be set.\n"); | |
| goto fail; | |
| } | |
| if (!set_irq(devc, CONF_MIDI, hw_config->irq)) { | |
| printk(KERN_ERR "PSS: MIDI IRQ allocation error.\n"); | |
| goto fail; | |
| } | |
| if (!pss_synthLen) { | |
| printk(KERN_ERR "PSS: Can't enable MPU. MIDI synth microcode not available.\n"); | |
| goto fail; | |
| } | |
| if (!pss_download_boot(devc, pss_synth, pss_synthLen, CPF_FIRST | CPF_LAST)) { | |
| printk(KERN_ERR "PSS: Unable to load MIDI synth microcode to DSP.\n"); | |
| goto fail; | |
| } | |
| /* | |
| * Finally wait until the DSP algorithm has initialized itself and | |
| * deactivates receive interrupt. | |
| */ | |
| for (timeout = 900000; timeout > 0; timeout--) | |
| { | |
| if ((inb(hw_config->io_base + 1) & 0x80) == 0) /* Input data avail */ | |
| inb(hw_config->io_base); /* Discard it */ | |
| else | |
| break; /* No more input */ | |
| } | |
| if (!probe_mpu401(hw_config, ports)) | |
| goto fail; | |
| attach_mpu401(hw_config, THIS_MODULE); /* Slot 1 */ | |
| if (hw_config->slots[1] != -1) /* The MPU driver installed itself */ | |
| midi_devs[hw_config->slots[1]]->coproc = &pss_coproc_operations; | |
| return 1; | |
| fail: | |
| release_region(hw_config->io_base, 2); | |
| return 0; | |
| } | |
| static int pss_coproc_open(void *dev_info, int sub_device) | |
| { | |
| switch (sub_device) | |
| { | |
| case COPR_MIDI: | |
| if (pss_synthLen == 0) | |
| { | |
| printk(KERN_ERR "PSS: MIDI synth microcode not available.\n"); | |
| return -EIO; | |
| } | |
| if (nonstandard_microcode) | |
| if (!pss_download_boot(devc, pss_synth, pss_synthLen, CPF_FIRST | CPF_LAST)) | |
| { | |
| printk(KERN_ERR "PSS: Unable to load MIDI synth microcode to DSP.\n"); | |
| return -EIO; | |
| } | |
| nonstandard_microcode = 0; | |
| break; | |
| default: | |
| break; | |
| } | |
| return 0; | |
| } | |
| static void pss_coproc_close(void *dev_info, int sub_device) | |
| { | |
| return; | |
| } | |
| static void pss_coproc_reset(void *dev_info) | |
| { | |
| if (pss_synthLen) | |
| if (!pss_download_boot(devc, pss_synth, pss_synthLen, CPF_FIRST | CPF_LAST)) | |
| { | |
| printk(KERN_ERR "PSS: Unable to load MIDI synth microcode to DSP.\n"); | |
| } | |
| nonstandard_microcode = 0; | |
| } | |
| static int download_boot_block(void *dev_info, copr_buffer * buf) | |
| { | |
| if (buf->len <= 0 || buf->len > sizeof(buf->data)) | |
| return -EINVAL; | |
| if (!pss_download_boot(devc, buf->data, buf->len, buf->flags)) | |
| { | |
| printk(KERN_ERR "PSS: Unable to load microcode block to DSP.\n"); | |
| return -EIO; | |
| } | |
| nonstandard_microcode = 1; /* The MIDI microcode has been overwritten */ | |
| return 0; | |
| } | |
| static int pss_coproc_ioctl(void *dev_info, unsigned int cmd, void __user *arg, int local) | |
| { | |
| copr_buffer *buf; | |
| copr_msg *mbuf; | |
| copr_debug_buf dbuf; | |
| unsigned short tmp; | |
| unsigned long flags; | |
| unsigned short *data; | |
| int i, err; | |
| /* printk( "PSS coproc ioctl %x %x %d\n", cmd, arg, local); */ | |
| switch (cmd) | |
| { | |
| case SNDCTL_COPR_RESET: | |
| pss_coproc_reset(dev_info); | |
| return 0; | |
| case SNDCTL_COPR_LOAD: | |
| buf = (copr_buffer *) vmalloc(sizeof(copr_buffer)); | |
| if (buf == NULL) | |
| return -ENOSPC; | |
| if (copy_from_user(buf, arg, sizeof(copr_buffer))) { | |
| vfree(buf); | |
| return -EFAULT; | |
| } | |
| err = download_boot_block(dev_info, buf); | |
| vfree(buf); | |
| return err; | |
| case SNDCTL_COPR_SENDMSG: | |
| mbuf = (copr_msg *)vmalloc(sizeof(copr_msg)); | |
| if (mbuf == NULL) | |
| return -ENOSPC; | |
| if (copy_from_user(mbuf, arg, sizeof(copr_msg))) { | |
| vfree(mbuf); | |
| return -EFAULT; | |
| } | |
| data = (unsigned short *)(mbuf->data); | |
| spin_lock_irqsave(&lock, flags); | |
| for (i = 0; i < mbuf->len; i++) { | |
| if (!pss_put_dspword(devc, *data++)) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| mbuf->len = i; /* feed back number of WORDs sent */ | |
| err = copy_to_user(arg, mbuf, sizeof(copr_msg)); | |
| vfree(mbuf); | |
| return err ? -EFAULT : -EIO; | |
| } | |
| } | |
| spin_unlock_irqrestore(&lock,flags); | |
| vfree(mbuf); | |
| return 0; | |
| case SNDCTL_COPR_RCVMSG: | |
| err = 0; | |
| mbuf = (copr_msg *)vmalloc(sizeof(copr_msg)); | |
| if (mbuf == NULL) | |
| return -ENOSPC; | |
| data = (unsigned short *)mbuf->data; | |
| spin_lock_irqsave(&lock, flags); | |
| for (i = 0; i < sizeof(mbuf->data)/sizeof(unsigned short); i++) { | |
| mbuf->len = i; /* feed back number of WORDs read */ | |
| if (!pss_get_dspword(devc, data++)) { | |
| if (i == 0) | |
| err = -EIO; | |
| break; | |
| } | |
| } | |
| spin_unlock_irqrestore(&lock,flags); | |
| if (copy_to_user(arg, mbuf, sizeof(copr_msg))) | |
| err = -EFAULT; | |
| vfree(mbuf); | |
| return err; | |
| case SNDCTL_COPR_RDATA: | |
| if (copy_from_user(&dbuf, arg, sizeof(dbuf))) | |
| return -EFAULT; | |
| spin_lock_irqsave(&lock, flags); | |
| if (!pss_put_dspword(devc, 0x00d0)) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| if (!pss_put_dspword(devc, (unsigned short)(dbuf.parm1 & 0xffff))) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| if (!pss_get_dspword(devc, &tmp)) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| dbuf.parm1 = tmp; | |
| spin_unlock_irqrestore(&lock,flags); | |
| if (copy_to_user(arg, &dbuf, sizeof(dbuf))) | |
| return -EFAULT; | |
| return 0; | |
| case SNDCTL_COPR_WDATA: | |
| if (copy_from_user(&dbuf, arg, sizeof(dbuf))) | |
| return -EFAULT; | |
| spin_lock_irqsave(&lock, flags); | |
| if (!pss_put_dspword(devc, 0x00d1)) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| if (!pss_put_dspword(devc, (unsigned short) (dbuf.parm1 & 0xffff))) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| tmp = (unsigned int)dbuf.parm2 & 0xffff; | |
| if (!pss_put_dspword(devc, tmp)) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| spin_unlock_irqrestore(&lock,flags); | |
| return 0; | |
| case SNDCTL_COPR_WCODE: | |
| if (copy_from_user(&dbuf, arg, sizeof(dbuf))) | |
| return -EFAULT; | |
| spin_lock_irqsave(&lock, flags); | |
| if (!pss_put_dspword(devc, 0x00d3)) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| if (!pss_put_dspword(devc, (unsigned short)(dbuf.parm1 & 0xffff))) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| tmp = (unsigned int)dbuf.parm2 & 0x00ff; | |
| if (!pss_put_dspword(devc, tmp)) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| tmp = ((unsigned int)dbuf.parm2 >> 8) & 0xffff; | |
| if (!pss_put_dspword(devc, tmp)) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| spin_unlock_irqrestore(&lock,flags); | |
| return 0; | |
| case SNDCTL_COPR_RCODE: | |
| if (copy_from_user(&dbuf, arg, sizeof(dbuf))) | |
| return -EFAULT; | |
| spin_lock_irqsave(&lock, flags); | |
| if (!pss_put_dspword(devc, 0x00d2)) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| if (!pss_put_dspword(devc, (unsigned short)(dbuf.parm1 & 0xffff))) { | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| if (!pss_get_dspword(devc, &tmp)) { /* Read MSB */ | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| dbuf.parm1 = tmp << 8; | |
| if (!pss_get_dspword(devc, &tmp)) { /* Read LSB */ | |
| spin_unlock_irqrestore(&lock,flags); | |
| return -EIO; | |
| } | |
| dbuf.parm1 |= tmp & 0x00ff; | |
| spin_unlock_irqrestore(&lock,flags); | |
| if (copy_to_user(arg, &dbuf, sizeof(dbuf))) | |
| return -EFAULT; | |
| return 0; | |
| default: | |
| return -EINVAL; | |
| } | |
| return -EINVAL; | |
| } | |
| static coproc_operations pss_coproc_operations = | |
| { | |
| "ADSP-2115", | |
| THIS_MODULE, | |
| pss_coproc_open, | |
| pss_coproc_close, | |
| pss_coproc_ioctl, | |
| pss_coproc_reset, | |
| &pss_data | |
| }; | |
| static int __init probe_pss_mss(struct address_info *hw_config) | |
| { | |
| volatile int timeout; | |
| struct resource *ports; | |
| int my_mix = -999; /* gcc shut up */ | |
| if (!pss_initialized) | |
| return 0; | |
| if (!request_region(hw_config->io_base, 4, "WSS config")) { | |
| printk(KERN_ERR "PSS: WSS I/O port conflicts.\n"); | |
| return 0; | |
| } | |
| ports = request_region(hw_config->io_base + 4, 4, "ad1848"); | |
| if (!ports) { | |
| printk(KERN_ERR "PSS: WSS I/O port conflicts.\n"); | |
| release_region(hw_config->io_base, 4); | |
| return 0; | |
| } | |
| if (!set_io_base(devc, CONF_WSS, hw_config->io_base)) { | |
| printk("PSS: WSS base not settable.\n"); | |
| goto fail; | |
| } | |
| if (!set_irq(devc, CONF_WSS, hw_config->irq)) { | |
| printk("PSS: WSS IRQ allocation error.\n"); | |
| goto fail; | |
| } | |
| if (!set_dma(devc, CONF_WSS, hw_config->dma)) { | |
| printk(KERN_ERR "PSS: WSS DMA allocation error\n"); | |
| goto fail; | |
| } | |
| /* | |
| * For some reason the card returns 0xff in the WSS status register | |
| * immediately after boot. Probably MIDI+SB emulation algorithm | |
| * downloaded to the ADSP2115 spends some time initializing the card. | |
| * Let's try to wait until it finishes this task. | |
| */ | |
| for (timeout = 0; timeout < 100000 && (inb(hw_config->io_base + WSS_INDEX) & | |
| WSS_INITIALIZING); timeout++) | |
| ; | |
| outb((0x0b), hw_config->io_base + WSS_INDEX); /* Required by some cards */ | |
| for (timeout = 0; (inb(hw_config->io_base + WSS_DATA) & WSS_AUTOCALIBRATION) && | |
| (timeout < 100000); timeout++) | |
| ; | |
| if (!probe_ms_sound(hw_config, ports)) | |
| goto fail; | |
| devc->ad_mixer_dev = NO_WSS_MIXER; | |
| if (pss_mixer) | |
| { | |
| if ((my_mix = sound_install_mixer (MIXER_DRIVER_VERSION, | |
| "PSS-SPEAKERS and AD1848 (through MSS audio codec)", | |
| &pss_mixer_operations, | |
| sizeof (struct mixer_operations), | |
| devc)) < 0) | |
| { | |
| printk(KERN_ERR "Could not install PSS mixer\n"); | |
| goto fail; | |
| } | |
| } | |
| pss_mixer_reset(devc); | |
| attach_ms_sound(hw_config, ports, THIS_MODULE); /* Slot 0 */ | |
| if (hw_config->slots[0] != -1) | |
| { | |
| /* The MSS driver installed itself */ | |
| audio_devs[hw_config->slots[0]]->coproc = &pss_coproc_operations; | |
| if (pss_mixer && (num_mixers == (my_mix + 2))) | |
| { | |
| /* The MSS mixer installed */ | |
| devc->ad_mixer_dev = audio_devs[hw_config->slots[0]]->mixer_dev; | |
| } | |
| } | |
| return 1; | |
| fail: | |
| release_region(hw_config->io_base + 4, 4); | |
| release_region(hw_config->io_base, 4); | |
| return 0; | |
| } | |
| static inline void __exit unload_pss(struct address_info *hw_config) | |
| { | |
| release_region(hw_config->io_base, 0x10); | |
| release_region(hw_config->io_base+0x10, 0x9); | |
| } | |
| static inline void __exit unload_pss_mpu(struct address_info *hw_config) | |
| { | |
| unload_mpu401(hw_config); | |
| } | |
| static inline void __exit unload_pss_mss(struct address_info *hw_config) | |
| { | |
| unload_ms_sound(hw_config); | |
| } | |
| static struct address_info cfg; | |
| static struct address_info cfg2; | |
| static struct address_info cfg_mpu; | |
| static int pss_io __initdata = -1; | |
| static int mss_io __initdata = -1; | |
| static int mss_irq __initdata = -1; | |
| static int mss_dma __initdata = -1; | |
| static int mpu_io __initdata = -1; | |
| static int mpu_irq __initdata = -1; | |
| static int pss_no_sound = 0; /* Just configure non-sound components */ | |
| static int pss_keep_settings = 1; /* Keep hardware settings at module exit */ | |
| static char *pss_firmware = "/etc/sound/pss_synth"; | |
| module_param(pss_io, int, 0); | |
| MODULE_PARM_DESC(pss_io, "Set i/o base of PSS card (probably 0x220 or 0x240)"); | |
| module_param(mss_io, int, 0); | |
| MODULE_PARM_DESC(mss_io, "Set WSS (audio) i/o base (0x530, 0x604, 0xE80, 0xF40, or other. Address must end in 0 or 4 and must be from 0x100 to 0xFF4)"); | |
| module_param(mss_irq, int, 0); | |
| MODULE_PARM_DESC(mss_irq, "Set WSS (audio) IRQ (3, 5, 7, 9, 10, 11, 12)"); | |
| module_param(mss_dma, int, 0); | |
| MODULE_PARM_DESC(mss_dma, "Set WSS (audio) DMA (0, 1, 3)"); | |
| module_param(mpu_io, int, 0); | |
| MODULE_PARM_DESC(mpu_io, "Set MIDI i/o base (0x330 or other. Address must be on 4 location boundaries and must be from 0x100 to 0xFFC)"); | |
| module_param(mpu_irq, int, 0); | |
| MODULE_PARM_DESC(mpu_irq, "Set MIDI IRQ (3, 5, 7, 9, 10, 11, 12)"); | |
| module_param(pss_cdrom_port, int, 0); | |
| MODULE_PARM_DESC(pss_cdrom_port, "Set the PSS CDROM port i/o base (0x340 or other)"); | |
| module_param(pss_enable_joystick, bool, 0); | |
| MODULE_PARM_DESC(pss_enable_joystick, "Enables the PSS joystick port (1 to enable, 0 to disable)"); | |
| module_param(pss_no_sound, bool, 0); | |
| MODULE_PARM_DESC(pss_no_sound, "Configure sound compoents (0 - no, 1 - yes)"); | |
| module_param(pss_keep_settings, bool, 0); | |
| MODULE_PARM_DESC(pss_keep_settings, "Keep hardware setting at driver unloading (0 - no, 1 - yes)"); | |
| module_param(pss_firmware, charp, 0); | |
| MODULE_PARM_DESC(pss_firmware, "Location of the firmware file (default - /etc/sound/pss_synth)"); | |
| module_param(pss_mixer, bool, 0); | |
| MODULE_PARM_DESC(pss_mixer, "Enable (1) or disable (0) PSS mixer (controlling of output volume, bass, treble, synth volume). The mixer is not available on all PSS cards."); | |
| MODULE_AUTHOR("Hannu Savolainen, Vladimir Michl"); | |
| MODULE_DESCRIPTION("Module for PSS sound cards (based on AD1848, ADSP-2115 and ESC614). This module includes control of output amplifier and synth volume of the Beethoven ADSP-16 card (this may work with other PSS cards)."); | |
| MODULE_LICENSE("GPL"); | |
| static int fw_load = 0; | |
| static int pssmpu = 0, pssmss = 0; | |
| /* | |
| * Load a PSS sound card module | |
| */ | |
| static int __init init_pss(void) | |
| { | |
| if(pss_no_sound) /* If configuring only nonsound components */ | |
| { | |
| cfg.io_base = pss_io; | |
| if(!probe_pss(&cfg)) | |
| return -ENODEV; | |
| printk(KERN_INFO "ECHO-PSS Rev. %d\n", inw(REG(PSS_ID)) & 0x00ff); | |
| printk(KERN_INFO "PSS: loading in no sound mode.\n"); | |
| disable_all_emulations(); | |
| configure_nonsound_components(); | |
| release_region(pss_io, 0x10); | |
| release_region(pss_io + 0x10, 0x9); | |
| return 0; | |
| } | |
| cfg.io_base = pss_io; | |
| cfg2.io_base = mss_io; | |
| cfg2.irq = mss_irq; | |
| cfg2.dma = mss_dma; | |
| cfg_mpu.io_base = mpu_io; | |
| cfg_mpu.irq = mpu_irq; | |
| if (cfg.io_base == -1 || cfg2.io_base == -1 || cfg2.irq == -1 || cfg.dma == -1) { | |
| printk(KERN_INFO "pss: mss_io, mss_dma, mss_irq and pss_io must be set.\n"); | |
| return -EINVAL; | |
| } | |
| if (!pss_synth) { | |
| fw_load = 1; | |
| pss_synthLen = mod_firmware_load(pss_firmware, (void *) &pss_synth); | |
| } | |
| if (!attach_pss(&cfg)) | |
| return -ENODEV; | |
| /* | |
| * Attach stuff | |
| */ | |
| if (probe_pss_mpu(&cfg_mpu)) | |
| pssmpu = 1; | |
| if (probe_pss_mss(&cfg2)) | |
| pssmss = 1; | |
| return 0; | |
| } | |
| static void __exit cleanup_pss(void) | |
| { | |
| if(!pss_no_sound) | |
| { | |
| if(fw_load && pss_synth) | |
| vfree(pss_synth); | |
| if(pssmss) | |
| unload_pss_mss(&cfg2); | |
| if(pssmpu) | |
| unload_pss_mpu(&cfg_mpu); | |
| unload_pss(&cfg); | |
| } | |
| if(!pss_keep_settings) /* Keep hardware settings if asked */ | |
| { | |
| disable_all_emulations(); | |
| printk(KERN_INFO "Resetting PSS sound card configurations.\n"); | |
| } | |
| } | |
| module_init(init_pss); | |
| module_exit(cleanup_pss); | |
| #ifndef MODULE | |
| static int __init setup_pss(char *str) | |
| { | |
| /* io, mss_io, mss_irq, mss_dma, mpu_io, mpu_irq */ | |
| int ints[7]; | |
| str = get_options(str, ARRAY_SIZE(ints), ints); | |
| pss_io = ints[1]; | |
| mss_io = ints[2]; | |
| mss_irq = ints[3]; | |
| mss_dma = ints[4]; | |
| mpu_io = ints[5]; | |
| mpu_irq = ints[6]; | |
| return 1; | |
| } | |
| __setup("pss=", setup_pss); | |
| #endif |