| /* $Id: os_pri.c,v 1.32 2004/03/21 17:26:01 armin Exp $ */ |
| |
| #include "platform.h" |
| #include "debuglib.h" |
| #include "cardtype.h" |
| #include "pc.h" |
| #include "pr_pc.h" |
| #include "di_defs.h" |
| #include "dsp_defs.h" |
| #include "di.h" |
| #include "io.h" |
| |
| #include "xdi_msg.h" |
| #include "xdi_adapter.h" |
| #include "os_pri.h" |
| #include "diva_pci.h" |
| #include "mi_pc.h" |
| #include "pc_maint.h" |
| #include "dsp_tst.h" |
| #include "diva_dma.h" |
| #include "dsrv_pri.h" |
| |
| /* -------------------------------------------------------------------------- |
| OS Dependent part of XDI driver for DIVA PRI Adapter |
| |
| DSP detection/validation by Anthony Booth (Eicon Networks, www.eicon.com) |
| -------------------------------------------------------------------------- */ |
| |
| #define DIVA_PRI_NO_PCI_BIOS_WORKAROUND 1 |
| |
| extern int diva_card_read_xlog(diva_os_xdi_adapter_t *a); |
| |
| /* |
| ** IMPORTS |
| */ |
| extern void prepare_pri_functions(PISDN_ADAPTER IoAdapter); |
| extern void prepare_pri2_functions(PISDN_ADAPTER IoAdapter); |
| extern void diva_xdi_display_adapter_features(int card); |
| |
| static int diva_pri_cleanup_adapter(diva_os_xdi_adapter_t *a); |
| static int diva_pri_cmd_card_proc(struct _diva_os_xdi_adapter *a, |
| diva_xdi_um_cfg_cmd_t *cmd, int length); |
| static int pri_get_serial_number(diva_os_xdi_adapter_t *a); |
| static int diva_pri_stop_adapter(diva_os_xdi_adapter_t *a); |
| static dword diva_pri_detect_dsps(diva_os_xdi_adapter_t *a); |
| |
| /* |
| ** Check card revision |
| */ |
| static int pri_is_rev_2_card(int card_ordinal) |
| { |
| switch (card_ordinal) { |
| case CARDTYPE_DIVASRV_P_30M_V2_PCI: |
| case CARDTYPE_DIVASRV_VOICE_P_30M_V2_PCI: |
| return (1); |
| } |
| return (0); |
| } |
| |
| static void diva_pri_set_addresses(diva_os_xdi_adapter_t *a) |
| { |
| a->resources.pci.mem_type_id[MEM_TYPE_ADDRESS] = 0; |
| a->resources.pci.mem_type_id[MEM_TYPE_CONTROL] = 2; |
| a->resources.pci.mem_type_id[MEM_TYPE_CONFIG] = 4; |
| a->resources.pci.mem_type_id[MEM_TYPE_RAM] = 0; |
| a->resources.pci.mem_type_id[MEM_TYPE_RESET] = 2; |
| a->resources.pci.mem_type_id[MEM_TYPE_CFG] = 4; |
| a->resources.pci.mem_type_id[MEM_TYPE_PROM] = 3; |
| |
| a->xdi_adapter.Address = a->resources.pci.addr[0]; |
| a->xdi_adapter.Control = a->resources.pci.addr[2]; |
| a->xdi_adapter.Config = a->resources.pci.addr[4]; |
| |
| a->xdi_adapter.ram = a->resources.pci.addr[0]; |
| a->xdi_adapter.ram += MP_SHARED_RAM_OFFSET; |
| |
| a->xdi_adapter.reset = a->resources.pci.addr[2]; |
| a->xdi_adapter.reset += MP_RESET; |
| |
| a->xdi_adapter.cfg = a->resources.pci.addr[4]; |
| a->xdi_adapter.cfg += MP_IRQ_RESET; |
| |
| a->xdi_adapter.sdram_bar = a->resources.pci.bar[0]; |
| |
| a->xdi_adapter.prom = a->resources.pci.addr[3]; |
| } |
| |
| /* |
| ** BAR0 - SDRAM, MP_MEMORY_SIZE, MP2_MEMORY_SIZE by Rev.2 |
| ** BAR1 - DEVICES, 0x1000 |
| ** BAR2 - CONTROL (REG), 0x2000 |
| ** BAR3 - FLASH (REG), 0x8000 |
| ** BAR4 - CONFIG (CFG), 0x1000 |
| */ |
| int diva_pri_init_card(diva_os_xdi_adapter_t *a) |
| { |
| int bar = 0; |
| int pri_rev_2; |
| unsigned long bar_length[5] = { |
| MP_MEMORY_SIZE, |
| 0x1000, |
| 0x2000, |
| 0x8000, |
| 0x1000 |
| }; |
| |
| pri_rev_2 = pri_is_rev_2_card(a->CardOrdinal); |
| |
| if (pri_rev_2) { |
| bar_length[0] = MP2_MEMORY_SIZE; |
| } |
| /* |
| Set properties |
| */ |
| a->xdi_adapter.Properties = CardProperties[a->CardOrdinal]; |
| DBG_LOG(("Load %s", a->xdi_adapter.Properties.Name)) |
| |
| /* |
| First initialization step: get and check hardware resoures. |
| Do not map resources and do not acecess card at this step |
| */ |
| for (bar = 0; bar < 5; bar++) { |
| a->resources.pci.bar[bar] = |
| divasa_get_pci_bar(a->resources.pci.bus, |
| a->resources.pci.func, bar, |
| a->resources.pci.hdev); |
| if (!a->resources.pci.bar[bar] |
| || (a->resources.pci.bar[bar] == 0xFFFFFFF0)) { |
| DBG_ERR(("A: invalid bar[%d]=%08x", bar, |
| a->resources.pci.bar[bar])) |
| return (-1); |
| } |
| } |
| a->resources.pci.irq = |
| (byte) divasa_get_pci_irq(a->resources.pci.bus, |
| a->resources.pci.func, |
| a->resources.pci.hdev); |
| if (!a->resources.pci.irq) { |
| DBG_ERR(("A: invalid irq")); |
| return (-1); |
| } |
| |
| /* |
| Map all BAR's |
| */ |
| for (bar = 0; bar < 5; bar++) { |
| a->resources.pci.addr[bar] = |
| divasa_remap_pci_bar(a, bar, a->resources.pci.bar[bar], |
| bar_length[bar]); |
| if (!a->resources.pci.addr[bar]) { |
| DBG_ERR(("A: A(%d), can't map bar[%d]", |
| a->controller, bar)) |
| diva_pri_cleanup_adapter(a); |
| return (-1); |
| } |
| } |
| |
| /* |
| Set all memory areas |
| */ |
| diva_pri_set_addresses(a); |
| |
| /* |
| Get Serial Number of this adapter |
| */ |
| if (pri_get_serial_number(a)) { |
| dword serNo; |
| serNo = a->resources.pci.bar[1] & 0xffff0000; |
| serNo |= ((dword) a->resources.pci.bus) << 8; |
| serNo += (a->resources.pci.func + a->controller + 1); |
| a->xdi_adapter.serialNo = serNo & ~0xFF000000; |
| DBG_ERR(("A: A(%d) can't get Serial Number, generated serNo=%ld", |
| a->controller, a->xdi_adapter.serialNo)) |
| } |
| |
| |
| /* |
| Initialize os objects |
| */ |
| if (diva_os_initialize_spin_lock(&a->xdi_adapter.isr_spin_lock, "isr")) { |
| diva_pri_cleanup_adapter(a); |
| return (-1); |
| } |
| if (diva_os_initialize_spin_lock |
| (&a->xdi_adapter.data_spin_lock, "data")) { |
| diva_pri_cleanup_adapter(a); |
| return (-1); |
| } |
| |
| strcpy(a->xdi_adapter.req_soft_isr.dpc_thread_name, "kdivasprid"); |
| |
| if (diva_os_initialize_soft_isr(&a->xdi_adapter.req_soft_isr, |
| DIDpcRoutine, &a->xdi_adapter)) { |
| diva_pri_cleanup_adapter(a); |
| return (-1); |
| } |
| |
| /* |
| Do not initialize second DPC - only one thread will be created |
| */ |
| a->xdi_adapter.isr_soft_isr.object = |
| a->xdi_adapter.req_soft_isr.object; |
| |
| /* |
| Next step of card initialization: |
| set up all interface pointers |
| */ |
| a->xdi_adapter.Channels = CardProperties[a->CardOrdinal].Channels; |
| a->xdi_adapter.e_max = CardProperties[a->CardOrdinal].E_info; |
| |
| a->xdi_adapter.e_tbl = |
| diva_os_malloc(0, a->xdi_adapter.e_max * sizeof(E_INFO)); |
| if (!a->xdi_adapter.e_tbl) { |
| diva_pri_cleanup_adapter(a); |
| return (-1); |
| } |
| memset(a->xdi_adapter.e_tbl, 0x00, a->xdi_adapter.e_max * sizeof(E_INFO)); |
| |
| a->xdi_adapter.a.io = &a->xdi_adapter; |
| a->xdi_adapter.DIRequest = request; |
| a->interface.cleanup_adapter_proc = diva_pri_cleanup_adapter; |
| a->interface.cmd_proc = diva_pri_cmd_card_proc; |
| |
| if (pri_rev_2) { |
| prepare_pri2_functions(&a->xdi_adapter); |
| } else { |
| prepare_pri_functions(&a->xdi_adapter); |
| } |
| |
| a->dsp_mask = diva_pri_detect_dsps(a); |
| |
| /* |
| Allocate DMA map |
| */ |
| if (pri_rev_2) { |
| diva_init_dma_map(a->resources.pci.hdev, |
| (struct _diva_dma_map_entry **) &a->xdi_adapter.dma_map, 32); |
| } |
| |
| /* |
| Set IRQ handler |
| */ |
| a->xdi_adapter.irq_info.irq_nr = a->resources.pci.irq; |
| sprintf(a->xdi_adapter.irq_info.irq_name, |
| "DIVA PRI %ld", (long) a->xdi_adapter.serialNo); |
| |
| if (diva_os_register_irq(a, a->xdi_adapter.irq_info.irq_nr, |
| a->xdi_adapter.irq_info.irq_name)) { |
| diva_pri_cleanup_adapter(a); |
| return (-1); |
| } |
| a->xdi_adapter.irq_info.registered = 1; |
| |
| diva_log_info("%s IRQ:%d SerNo:%d", a->xdi_adapter.Properties.Name, |
| a->resources.pci.irq, a->xdi_adapter.serialNo); |
| |
| return (0); |
| } |
| |
| static int diva_pri_cleanup_adapter(diva_os_xdi_adapter_t *a) |
| { |
| int bar = 0; |
| |
| /* |
| Stop Adapter if adapter is running |
| */ |
| if (a->xdi_adapter.Initialized) { |
| diva_pri_stop_adapter(a); |
| } |
| |
| /* |
| Remove ISR Handler |
| */ |
| if (a->xdi_adapter.irq_info.registered) { |
| diva_os_remove_irq(a, a->xdi_adapter.irq_info.irq_nr); |
| } |
| a->xdi_adapter.irq_info.registered = 0; |
| |
| /* |
| Step 1: unmap all BAR's, if any was mapped |
| */ |
| for (bar = 0; bar < 5; bar++) { |
| if (a->resources.pci.bar[bar] |
| && a->resources.pci.addr[bar]) { |
| divasa_unmap_pci_bar(a->resources.pci.addr[bar]); |
| a->resources.pci.bar[bar] = 0; |
| a->resources.pci.addr[bar] = NULL; |
| } |
| } |
| |
| /* |
| Free OS objects |
| */ |
| diva_os_cancel_soft_isr(&a->xdi_adapter.isr_soft_isr); |
| diva_os_cancel_soft_isr(&a->xdi_adapter.req_soft_isr); |
| |
| diva_os_remove_soft_isr(&a->xdi_adapter.req_soft_isr); |
| a->xdi_adapter.isr_soft_isr.object = NULL; |
| |
| diva_os_destroy_spin_lock(&a->xdi_adapter.isr_spin_lock, "rm"); |
| diva_os_destroy_spin_lock(&a->xdi_adapter.data_spin_lock, "rm"); |
| |
| /* |
| Free memory accupied by XDI adapter |
| */ |
| if (a->xdi_adapter.e_tbl) { |
| diva_os_free(0, a->xdi_adapter.e_tbl); |
| a->xdi_adapter.e_tbl = NULL; |
| } |
| a->xdi_adapter.Channels = 0; |
| a->xdi_adapter.e_max = 0; |
| |
| |
| /* |
| Free adapter DMA map |
| */ |
| diva_free_dma_map(a->resources.pci.hdev, |
| (struct _diva_dma_map_entry *) a->xdi_adapter. |
| dma_map); |
| a->xdi_adapter.dma_map = NULL; |
| |
| |
| /* |
| Detach this adapter from debug driver |
| */ |
| |
| return (0); |
| } |
| |
| /* |
| ** Activate On Board Boot Loader |
| */ |
| static int diva_pri_reset_adapter(PISDN_ADAPTER IoAdapter) |
| { |
| dword i; |
| struct mp_load __iomem *boot; |
| |
| if (!IoAdapter->Address || !IoAdapter->reset) { |
| return (-1); |
| } |
| if (IoAdapter->Initialized) { |
| DBG_ERR(("A: A(%d) can't reset PRI adapter - please stop first", |
| IoAdapter->ANum)) |
| return (-1); |
| } |
| |
| boot = (struct mp_load __iomem *) DIVA_OS_MEM_ATTACH_ADDRESS(IoAdapter); |
| WRITE_DWORD(&boot->err, 0); |
| DIVA_OS_MEM_DETACH_ADDRESS(IoAdapter, boot); |
| |
| IoAdapter->rstFnc(IoAdapter); |
| |
| diva_os_wait(10); |
| |
| boot = (struct mp_load __iomem *) DIVA_OS_MEM_ATTACH_ADDRESS(IoAdapter); |
| i = READ_DWORD(&boot->live); |
| |
| diva_os_wait(10); |
| if (i == READ_DWORD(&boot->live)) { |
| DIVA_OS_MEM_DETACH_ADDRESS(IoAdapter, boot); |
| DBG_ERR(("A: A(%d) CPU on PRI %ld is not alive!", |
| IoAdapter->ANum, IoAdapter->serialNo)) |
| return (-1); |
| } |
| if (READ_DWORD(&boot->err)) { |
| DBG_ERR(("A: A(%d) PRI %ld Board Selftest failed, error=%08lx", |
| IoAdapter->ANum, IoAdapter->serialNo, |
| READ_DWORD(&boot->err))) |
| DIVA_OS_MEM_DETACH_ADDRESS(IoAdapter, boot); |
| return (-1); |
| } |
| DIVA_OS_MEM_DETACH_ADDRESS(IoAdapter, boot); |
| |
| /* |
| Forget all outstanding entities |
| */ |
| IoAdapter->e_count = 0; |
| if (IoAdapter->e_tbl) { |
| memset(IoAdapter->e_tbl, 0x00, |
| IoAdapter->e_max * sizeof(E_INFO)); |
| } |
| IoAdapter->head = 0; |
| IoAdapter->tail = 0; |
| IoAdapter->assign = 0; |
| IoAdapter->trapped = 0; |
| |
| memset(&IoAdapter->a.IdTable[0], 0x00, |
| sizeof(IoAdapter->a.IdTable)); |
| memset(&IoAdapter->a.IdTypeTable[0], 0x00, |
| sizeof(IoAdapter->a.IdTypeTable)); |
| memset(&IoAdapter->a.FlowControlIdTable[0], 0x00, |
| sizeof(IoAdapter->a.FlowControlIdTable)); |
| memset(&IoAdapter->a.FlowControlSkipTable[0], 0x00, |
| sizeof(IoAdapter->a.FlowControlSkipTable)); |
| memset(&IoAdapter->a.misc_flags_table[0], 0x00, |
| sizeof(IoAdapter->a.misc_flags_table)); |
| memset(&IoAdapter->a.rx_stream[0], 0x00, |
| sizeof(IoAdapter->a.rx_stream)); |
| memset(&IoAdapter->a.tx_stream[0], 0x00, |
| sizeof(IoAdapter->a.tx_stream)); |
| memset(&IoAdapter->a.tx_pos[0], 0x00, sizeof(IoAdapter->a.tx_pos)); |
| memset(&IoAdapter->a.rx_pos[0], 0x00, sizeof(IoAdapter->a.rx_pos)); |
| |
| return (0); |
| } |
| |
| static int |
| diva_pri_write_sdram_block(PISDN_ADAPTER IoAdapter, |
| dword address, |
| const byte *data, dword length, dword limit) |
| { |
| byte __iomem *p = DIVA_OS_MEM_ATTACH_ADDRESS(IoAdapter); |
| byte __iomem *mem = p; |
| |
| if (((address + length) >= limit) || !mem) { |
| DIVA_OS_MEM_DETACH_ADDRESS(IoAdapter, p); |
| DBG_ERR(("A: A(%d) write PRI address=0x%08lx", |
| IoAdapter->ANum, address + length)) |
| return (-1); |
| } |
| mem += address; |
| |
| /* memcpy_toio(), maybe? */ |
| while (length--) { |
| WRITE_BYTE(mem++, *data++); |
| } |
| |
| DIVA_OS_MEM_DETACH_ADDRESS(IoAdapter, p); |
| return (0); |
| } |
| |
| static int |
| diva_pri_start_adapter(PISDN_ADAPTER IoAdapter, |
| dword start_address, dword features) |
| { |
| dword i; |
| int started = 0; |
| byte __iomem *p; |
| struct mp_load __iomem *boot = (struct mp_load __iomem *) DIVA_OS_MEM_ATTACH_ADDRESS(IoAdapter); |
| ADAPTER *a = &IoAdapter->a; |
| |
| if (IoAdapter->Initialized) { |
| DIVA_OS_MEM_DETACH_ADDRESS(IoAdapter, boot); |
| DBG_ERR(("A: A(%d) pri_start_adapter, adapter already running", |
| IoAdapter->ANum)) |
| return (-1); |
| } |
| if (!boot) { |
| DIVA_OS_MEM_DETACH_ADDRESS(IoAdapter, boot); |
| DBG_ERR(("A: PRI %ld can't start, adapter not mapped", |
| IoAdapter->serialNo)) |
| return (-1); |
| } |
| |
| sprintf(IoAdapter->Name, "A(%d)", (int) IoAdapter->ANum); |
| DBG_LOG(("A(%d) start PRI at 0x%08lx", IoAdapter->ANum, |
| start_address)) |
| |
| WRITE_DWORD(&boot->addr, start_address); |
| WRITE_DWORD(&boot->cmd, 3); |
| |
| for (i = 0; i < 300; ++i) { |
| diva_os_wait(10); |
| if ((READ_DWORD(&boot->signature) >> 16) == 0x4447) { |
| DBG_LOG(("A(%d) Protocol startup time %d.%02d seconds", |
| IoAdapter->ANum, (i / 100), (i % 100))) |
| started = 1; |
| break; |
| } |
| } |
| |
| if (!started) { |
| byte __iomem *p = (byte __iomem *)boot; |
| dword TrapId; |
| dword debug; |
| TrapId = READ_DWORD(&p[0x80]); |
| debug = READ_DWORD(&p[0x1c]); |
| DBG_ERR(("A(%d) Adapter start failed 0x%08lx, TrapId=%08lx, debug=%08lx", |
| IoAdapter->ANum, READ_DWORD(&boot->signature), |
| TrapId, debug)) |
| DIVA_OS_MEM_DETACH_ADDRESS(IoAdapter, boot); |
| if (IoAdapter->trapFnc) { |
| (*(IoAdapter->trapFnc)) (IoAdapter); |
| } |
| IoAdapter->stop(IoAdapter); |
| return (-1); |
| } |
| DIVA_OS_MEM_DETACH_ADDRESS(IoAdapter, boot); |
| |
| IoAdapter->Initialized = true; |
| |
| /* |
| Check Interrupt |
| */ |
| IoAdapter->IrqCount = 0; |
| p = DIVA_OS_MEM_ATTACH_CFG(IoAdapter); |
| WRITE_DWORD(p, (dword)~0x03E00000); |
| DIVA_OS_MEM_DETACH_CFG(IoAdapter, p); |
| a->ReadyInt = 1; |
| a->ram_out(a, &PR_RAM->ReadyInt, 1); |
| |
| for (i = 100; !IoAdapter->IrqCount && (i-- > 0); diva_os_wait(10)); |
| |
| if (!IoAdapter->IrqCount) { |
| DBG_ERR(("A: A(%d) interrupt test failed", |
| IoAdapter->ANum)) |
| IoAdapter->Initialized = false; |
| IoAdapter->stop(IoAdapter); |
| return (-1); |
| } |
| |
| IoAdapter->Properties.Features = (word) features; |
| |
| diva_xdi_display_adapter_features(IoAdapter->ANum); |
| |
| DBG_LOG(("A(%d) PRI adapter successfully started", IoAdapter->ANum)) |
| /* |
| Register with DIDD |
| */ |
| diva_xdi_didd_register_adapter(IoAdapter->ANum); |
| |
| return (0); |
| } |
| |
| static void diva_pri_clear_interrupts(diva_os_xdi_adapter_t *a) |
| { |
| PISDN_ADAPTER IoAdapter = &a->xdi_adapter; |
| |
| /* |
| clear any pending interrupt |
| */ |
| IoAdapter->disIrq(IoAdapter); |
| |
| IoAdapter->tst_irq(&IoAdapter->a); |
| IoAdapter->clr_irq(&IoAdapter->a); |
| IoAdapter->tst_irq(&IoAdapter->a); |
| |
| /* |
| kill pending dpcs |
| */ |
| diva_os_cancel_soft_isr(&IoAdapter->req_soft_isr); |
| diva_os_cancel_soft_isr(&IoAdapter->isr_soft_isr); |
| } |
| |
| /* |
| ** Stop Adapter, but do not unmap/unregister - adapter |
| ** will be restarted later |
| */ |
| static int diva_pri_stop_adapter(diva_os_xdi_adapter_t *a) |
| { |
| PISDN_ADAPTER IoAdapter = &a->xdi_adapter; |
| int i = 100; |
| |
| if (!IoAdapter->ram) { |
| return (-1); |
| } |
| if (!IoAdapter->Initialized) { |
| DBG_ERR(("A: A(%d) can't stop PRI adapter - not running", |
| IoAdapter->ANum)) |
| return (-1); /* nothing to stop */ |
| } |
| IoAdapter->Initialized = 0; |
| |
| /* |
| Disconnect Adapter from DIDD |
| */ |
| diva_xdi_didd_remove_adapter(IoAdapter->ANum); |
| |
| /* |
| Stop interrupts |
| */ |
| a->clear_interrupts_proc = diva_pri_clear_interrupts; |
| IoAdapter->a.ReadyInt = 1; |
| IoAdapter->a.ram_inc(&IoAdapter->a, &PR_RAM->ReadyInt); |
| do { |
| diva_os_sleep(10); |
| } while (i-- && a->clear_interrupts_proc); |
| |
| if (a->clear_interrupts_proc) { |
| diva_pri_clear_interrupts(a); |
| a->clear_interrupts_proc = NULL; |
| DBG_ERR(("A: A(%d) no final interrupt from PRI adapter", |
| IoAdapter->ANum)) |
| } |
| IoAdapter->a.ReadyInt = 0; |
| |
| /* |
| Stop and reset adapter |
| */ |
| IoAdapter->stop(IoAdapter); |
| |
| return (0); |
| } |
| |
| /* |
| ** Process commands form configuration/download framework and from |
| ** user mode |
| ** |
| ** return 0 on success |
| */ |
| static int |
| diva_pri_cmd_card_proc(struct _diva_os_xdi_adapter *a, |
| diva_xdi_um_cfg_cmd_t *cmd, int length) |
| { |
| int ret = -1; |
| |
| if (cmd->adapter != a->controller) { |
| DBG_ERR(("A: pri_cmd, invalid controller=%d != %d", |
| cmd->adapter, a->controller)) |
| return (-1); |
| } |
| |
| switch (cmd->command) { |
| case DIVA_XDI_UM_CMD_GET_CARD_ORDINAL: |
| a->xdi_mbox.data_length = sizeof(dword); |
| a->xdi_mbox.data = |
| diva_os_malloc(0, a->xdi_mbox.data_length); |
| if (a->xdi_mbox.data) { |
| *(dword *) a->xdi_mbox.data = |
| (dword) a->CardOrdinal; |
| a->xdi_mbox.status = DIVA_XDI_MBOX_BUSY; |
| ret = 0; |
| } |
| break; |
| |
| case DIVA_XDI_UM_CMD_GET_SERIAL_NR: |
| a->xdi_mbox.data_length = sizeof(dword); |
| a->xdi_mbox.data = |
| diva_os_malloc(0, a->xdi_mbox.data_length); |
| if (a->xdi_mbox.data) { |
| *(dword *) a->xdi_mbox.data = |
| (dword) a->xdi_adapter.serialNo; |
| a->xdi_mbox.status = DIVA_XDI_MBOX_BUSY; |
| ret = 0; |
| } |
| break; |
| |
| case DIVA_XDI_UM_CMD_GET_PCI_HW_CONFIG: |
| a->xdi_mbox.data_length = sizeof(dword) * 9; |
| a->xdi_mbox.data = |
| diva_os_malloc(0, a->xdi_mbox.data_length); |
| if (a->xdi_mbox.data) { |
| int i; |
| dword *data = (dword *) a->xdi_mbox.data; |
| |
| for (i = 0; i < 8; i++) { |
| *data++ = a->resources.pci.bar[i]; |
| } |
| *data++ = (dword) a->resources.pci.irq; |
| a->xdi_mbox.status = DIVA_XDI_MBOX_BUSY; |
| ret = 0; |
| } |
| break; |
| |
| case DIVA_XDI_UM_CMD_RESET_ADAPTER: |
| ret = diva_pri_reset_adapter(&a->xdi_adapter); |
| break; |
| |
| case DIVA_XDI_UM_CMD_WRITE_SDRAM_BLOCK: |
| ret = diva_pri_write_sdram_block(&a->xdi_adapter, |
| cmd->command_data. |
| write_sdram.offset, |
| (byte *)&cmd[1], |
| cmd->command_data. |
| write_sdram.length, |
| pri_is_rev_2_card(a-> |
| CardOrdinal) |
| ? MP2_MEMORY_SIZE : |
| MP_MEMORY_SIZE); |
| break; |
| |
| case DIVA_XDI_UM_CMD_STOP_ADAPTER: |
| ret = diva_pri_stop_adapter(a); |
| break; |
| |
| case DIVA_XDI_UM_CMD_START_ADAPTER: |
| ret = diva_pri_start_adapter(&a->xdi_adapter, |
| cmd->command_data.start. |
| offset, |
| cmd->command_data.start. |
| features); |
| break; |
| |
| case DIVA_XDI_UM_CMD_SET_PROTOCOL_FEATURES: |
| a->xdi_adapter.features = |
| cmd->command_data.features.features; |
| a->xdi_adapter.a.protocol_capabilities = |
| a->xdi_adapter.features; |
| DBG_TRC(("Set raw protocol features (%08x)", |
| a->xdi_adapter.features)) |
| ret = 0; |
| break; |
| |
| case DIVA_XDI_UM_CMD_GET_CARD_STATE: |
| a->xdi_mbox.data_length = sizeof(dword); |
| a->xdi_mbox.data = |
| diva_os_malloc(0, a->xdi_mbox.data_length); |
| if (a->xdi_mbox.data) { |
| dword *data = (dword *) a->xdi_mbox.data; |
| if (!a->xdi_adapter.ram || |
| !a->xdi_adapter.reset || |
| !a->xdi_adapter.cfg) { |
| *data = 3; |
| } else if (a->xdi_adapter.trapped) { |
| *data = 2; |
| } else if (a->xdi_adapter.Initialized) { |
| *data = 1; |
| } else { |
| *data = 0; |
| } |
| a->xdi_mbox.status = DIVA_XDI_MBOX_BUSY; |
| ret = 0; |
| } |
| break; |
| |
| case DIVA_XDI_UM_CMD_READ_XLOG_ENTRY: |
| ret = diva_card_read_xlog(a); |
| break; |
| |
| case DIVA_XDI_UM_CMD_READ_SDRAM: |
| if (a->xdi_adapter.Address) { |
| if ( |
| (a->xdi_mbox.data_length = |
| cmd->command_data.read_sdram.length)) { |
| if ( |
| (a->xdi_mbox.data_length + |
| cmd->command_data.read_sdram.offset) < |
| a->xdi_adapter.MemorySize) { |
| a->xdi_mbox.data = |
| diva_os_malloc(0, |
| a->xdi_mbox. |
| data_length); |
| if (a->xdi_mbox.data) { |
| byte __iomem *p = DIVA_OS_MEM_ATTACH_ADDRESS(&a->xdi_adapter); |
| byte __iomem *src = p; |
| byte *dst = a->xdi_mbox.data; |
| dword len = a->xdi_mbox.data_length; |
| |
| src += cmd->command_data.read_sdram.offset; |
| |
| while (len--) { |
| *dst++ = READ_BYTE(src++); |
| } |
| a->xdi_mbox.status = DIVA_XDI_MBOX_BUSY; |
| DIVA_OS_MEM_DETACH_ADDRESS(&a->xdi_adapter, p); |
| ret = 0; |
| } |
| } |
| } |
| } |
| break; |
| |
| default: |
| DBG_ERR(("A: A(%d) invalid cmd=%d", a->controller, |
| cmd->command)) |
| } |
| |
| return (ret); |
| } |
| |
| /* |
| ** Get Serial Number |
| */ |
| static int pri_get_serial_number(diva_os_xdi_adapter_t *a) |
| { |
| byte data[64]; |
| int i; |
| dword len = sizeof(data); |
| volatile byte __iomem *config; |
| volatile byte __iomem *flash; |
| byte c; |
| |
| /* |
| * First set some GT6401x config registers before accessing the BOOT-ROM |
| */ |
| config = DIVA_OS_MEM_ATTACH_CONFIG(&a->xdi_adapter); |
| c = READ_BYTE(&config[0xc3c]); |
| if (!(c & 0x08)) { |
| WRITE_BYTE(&config[0xc3c], c); /* Base Address enable register */ |
| } |
| WRITE_BYTE(&config[LOW_BOOTCS_DREG], 0x00); |
| WRITE_BYTE(&config[HI_BOOTCS_DREG], 0xFF); |
| DIVA_OS_MEM_DETACH_CONFIG(&a->xdi_adapter, config); |
| /* |
| * Read only the last 64 bytes of manufacturing data |
| */ |
| memset(data, '\0', len); |
| flash = DIVA_OS_MEM_ATTACH_PROM(&a->xdi_adapter); |
| for (i = 0; i < len; i++) { |
| data[i] = READ_BYTE(&flash[0x8000 - len + i]); |
| } |
| DIVA_OS_MEM_DETACH_PROM(&a->xdi_adapter, flash); |
| |
| config = DIVA_OS_MEM_ATTACH_CONFIG(&a->xdi_adapter); |
| WRITE_BYTE(&config[LOW_BOOTCS_DREG], 0xFC); /* Disable FLASH EPROM access */ |
| WRITE_BYTE(&config[HI_BOOTCS_DREG], 0xFF); |
| DIVA_OS_MEM_DETACH_CONFIG(&a->xdi_adapter, config); |
| |
| if (memcmp(&data[48], "DIVAserverPR", 12)) { |
| #if !defined(DIVA_PRI_NO_PCI_BIOS_WORKAROUND) /* { */ |
| word cmd = 0, cmd_org; |
| void *addr; |
| dword addr1, addr3, addr4; |
| byte Bus, Slot; |
| void *hdev; |
| addr4 = a->resources.pci.bar[4]; |
| addr3 = a->resources.pci.bar[3]; /* flash */ |
| addr1 = a->resources.pci.bar[1]; /* unused */ |
| |
| DBG_ERR(("A: apply Compaq BIOS workaround")) |
| DBG_LOG(("%02x:%02x:%02x:%02x:%02x:%02x:%02x:%02x", |
| data[0], data[1], data[2], data[3], |
| data[4], data[5], data[6], data[7])) |
| |
| Bus = a->resources.pci.bus; |
| Slot = a->resources.pci.func; |
| hdev = a->resources.pci.hdev; |
| PCIread(Bus, Slot, 0x04, &cmd_org, sizeof(cmd_org), hdev); |
| PCIwrite(Bus, Slot, 0x04, &cmd, sizeof(cmd), hdev); |
| |
| PCIwrite(Bus, Slot, 0x14, &addr4, sizeof(addr4), hdev); |
| PCIwrite(Bus, Slot, 0x20, &addr1, sizeof(addr1), hdev); |
| |
| PCIwrite(Bus, Slot, 0x04, &cmd_org, sizeof(cmd_org), hdev); |
| |
| addr = a->resources.pci.addr[1]; |
| a->resources.pci.addr[1] = a->resources.pci.addr[4]; |
| a->resources.pci.addr[4] = addr; |
| |
| addr1 = a->resources.pci.bar[1]; |
| a->resources.pci.bar[1] = a->resources.pci.bar[4]; |
| a->resources.pci.bar[4] = addr1; |
| |
| /* |
| Try to read Flash again |
| */ |
| len = sizeof(data); |
| |
| config = DIVA_OS_MEM_ATTACH_CONFIG(&a->xdi_adapter); |
| if (!(config[0xc3c] & 0x08)) { |
| config[0xc3c] |= 0x08; /* Base Address enable register */ |
| } |
| config[LOW_BOOTCS_DREG] = 0x00; |
| config[HI_BOOTCS_DREG] = 0xFF; |
| DIVA_OS_MEM_DETACH_CONFIG(&a->xdi_adapter, config); |
| |
| memset(data, '\0', len); |
| flash = DIVA_OS_MEM_ATTACH_PROM(&a->xdi_adapter); |
| for (i = 0; i < len; i++) { |
| data[i] = flash[0x8000 - len + i]; |
| } |
| DIVA_OS_MEM_ATTACH_PROM(&a->xdi_adapter, flash); |
| config = DIVA_OS_MEM_ATTACH_CONFIG(&a->xdi_adapter); |
| config[LOW_BOOTCS_DREG] = 0xFC; |
| config[HI_BOOTCS_DREG] = 0xFF; |
| DIVA_OS_MEM_DETACH_CONFIG(&a->xdi_adapter, config); |
| |
| if (memcmp(&data[48], "DIVAserverPR", 12)) { |
| DBG_ERR(("A: failed to read serial number")) |
| DBG_LOG(("%02x:%02x:%02x:%02x:%02x:%02x:%02x:%02x", |
| data[0], data[1], data[2], data[3], |
| data[4], data[5], data[6], data[7])) |
| return (-1); |
| } |
| #else /* } { */ |
| DBG_ERR(("A: failed to read DIVA signature word")) |
| DBG_LOG(("%02x:%02x:%02x:%02x:%02x:%02x:%02x:%02x", |
| data[0], data[1], data[2], data[3], |
| data[4], data[5], data[6], data[7])) |
| DBG_LOG(("%02x:%02x:%02x:%02x", data[47], data[46], |
| data[45], data[44])) |
| #endif /* } */ |
| } |
| |
| a->xdi_adapter.serialNo = |
| (data[47] << 24) | (data[46] << 16) | (data[45] << 8) | |
| data[44]; |
| if (!a->xdi_adapter.serialNo |
| || (a->xdi_adapter.serialNo == 0xffffffff)) { |
| a->xdi_adapter.serialNo = 0; |
| DBG_ERR(("A: failed to read serial number")) |
| return (-1); |
| } |
| |
| DBG_LOG(("Serial No. : %ld", a->xdi_adapter.serialNo)) |
| DBG_TRC(("Board Revision : %d.%02d", (int) data[41], |
| (int) data[40])) |
| DBG_TRC(("PLD revision : %d.%02d", (int) data[33], |
| (int) data[32])) |
| DBG_TRC(("Boot loader version : %d.%02d", (int) data[37], |
| (int) data[36])) |
| |
| DBG_TRC(("Manufacturing Date : %d/%02d/%02d (yyyy/mm/dd)", |
| (int) ((data[28] > 90) ? 1900 : 2000) + |
| (int) data[28], (int) data[29], (int) data[30])) |
| |
| return (0); |
| } |
| |
| void diva_os_prepare_pri2_functions(PISDN_ADAPTER IoAdapter) |
| { |
| } |
| |
| void diva_os_prepare_pri_functions(PISDN_ADAPTER IoAdapter) |
| { |
| } |
| |
| /* |
| ** Checks presence of DSP on board |
| */ |
| static int |
| dsp_check_presence(volatile byte __iomem *addr, volatile byte __iomem *data, int dsp) |
| { |
| word pattern; |
| |
| WRITE_WORD(addr, 0x4000); |
| WRITE_WORD(data, DSP_SIGNATURE_PROBE_WORD); |
| |
| WRITE_WORD(addr, 0x4000); |
| pattern = READ_WORD(data); |
| |
| if (pattern != DSP_SIGNATURE_PROBE_WORD) { |
| DBG_TRC(("W: DSP[%d] %04x(is) != %04x(should)", |
| dsp, pattern, DSP_SIGNATURE_PROBE_WORD)) |
| return (-1); |
| } |
| |
| WRITE_WORD(addr, 0x4000); |
| WRITE_WORD(data, ~DSP_SIGNATURE_PROBE_WORD); |
| |
| WRITE_WORD(addr, 0x4000); |
| pattern = READ_WORD(data); |
| |
| if (pattern != (word)~DSP_SIGNATURE_PROBE_WORD) { |
| DBG_ERR(("A: DSP[%d] %04x(is) != %04x(should)", |
| dsp, pattern, (word)~DSP_SIGNATURE_PROBE_WORD)) |
| return (-2); |
| } |
| |
| DBG_TRC(("DSP[%d] present", dsp)) |
| |
| return (0); |
| } |
| |
| |
| /* |
| ** Check if DSP's are present and operating |
| ** Information about detected DSP's is returned as bit mask |
| ** Bit 0 - DSP1 |
| ** ... |
| ** ... |
| ** ... |
| ** Bit 29 - DSP30 |
| */ |
| static dword diva_pri_detect_dsps(diva_os_xdi_adapter_t *a) |
| { |
| byte __iomem *base; |
| byte __iomem *p; |
| dword ret = 0; |
| dword row_offset[7] = { |
| 0x00000000, |
| 0x00000800, /* 1 - ROW 1 */ |
| 0x00000840, /* 2 - ROW 2 */ |
| 0x00001000, /* 3 - ROW 3 */ |
| 0x00001040, /* 4 - ROW 4 */ |
| 0x00000000 /* 5 - ROW 0 */ |
| }; |
| |
| byte __iomem *dsp_addr_port; |
| byte __iomem *dsp_data_port; |
| byte row_state; |
| int dsp_row = 0, dsp_index, dsp_num; |
| |
| if (!a->xdi_adapter.Control || !a->xdi_adapter.reset) { |
| return (0); |
| } |
| |
| p = DIVA_OS_MEM_ATTACH_RESET(&a->xdi_adapter); |
| WRITE_BYTE(p, _MP_RISC_RESET | _MP_DSP_RESET); |
| DIVA_OS_MEM_DETACH_RESET(&a->xdi_adapter, p); |
| diva_os_wait(5); |
| |
| base = DIVA_OS_MEM_ATTACH_CONTROL(&a->xdi_adapter); |
| |
| for (dsp_num = 0; dsp_num < 30; dsp_num++) { |
| dsp_row = dsp_num / 7 + 1; |
| dsp_index = dsp_num % 7; |
| |
| dsp_data_port = base; |
| dsp_addr_port = base; |
| |
| dsp_data_port += row_offset[dsp_row]; |
| dsp_addr_port += row_offset[dsp_row]; |
| |
| dsp_data_port += (dsp_index * 8); |
| dsp_addr_port += (dsp_index * 8) + 0x80; |
| |
| if (!dsp_check_presence |
| (dsp_addr_port, dsp_data_port, dsp_num + 1)) { |
| ret |= (1 << dsp_num); |
| } |
| } |
| DIVA_OS_MEM_DETACH_CONTROL(&a->xdi_adapter, base); |
| |
| p = DIVA_OS_MEM_ATTACH_RESET(&a->xdi_adapter); |
| WRITE_BYTE(p, _MP_RISC_RESET | _MP_LED1 | _MP_LED2); |
| DIVA_OS_MEM_DETACH_RESET(&a->xdi_adapter, p); |
| diva_os_wait(5); |
| |
| /* |
| Verify modules |
| */ |
| for (dsp_row = 0; dsp_row < 4; dsp_row++) { |
| row_state = ((ret >> (dsp_row * 7)) & 0x7F); |
| if (row_state && (row_state != 0x7F)) { |
| for (dsp_index = 0; dsp_index < 7; dsp_index++) { |
| if (!(row_state & (1 << dsp_index))) { |
| DBG_ERR(("A: MODULE[%d]-DSP[%d] failed", |
| dsp_row + 1, |
| dsp_index + 1)) |
| } |
| } |
| } |
| } |
| |
| if (!(ret & 0x10000000)) { |
| DBG_ERR(("A: ON BOARD-DSP[1] failed")) |
| } |
| if (!(ret & 0x20000000)) { |
| DBG_ERR(("A: ON BOARD-DSP[2] failed")) |
| } |
| |
| /* |
| Print module population now |
| */ |
| DBG_LOG(("+-----------------------+")) |
| DBG_LOG(("| DSP MODULE POPULATION |")) |
| DBG_LOG(("+-----------------------+")) |
| DBG_LOG(("| 1 | 2 | 3 | 4 |")) |
| DBG_LOG(("+-----------------------+")) |
| DBG_LOG(("| %s | %s | %s | %s |", |
| ((ret >> (0 * 7)) & 0x7F) ? "Y" : "N", |
| ((ret >> (1 * 7)) & 0x7F) ? "Y" : "N", |
| ((ret >> (2 * 7)) & 0x7F) ? "Y" : "N", |
| ((ret >> (3 * 7)) & 0x7F) ? "Y" : "N")) |
| DBG_LOG(("+-----------------------+")) |
| |
| DBG_LOG(("DSP's(present-absent):%08x-%08x", ret, |
| ~ret & 0x3fffffff)) |
| |
| return (ret); |
| } |