blob: 8862ec907fd8e9564aa9d8e5ed4aba173f6a2623 [file] [log] [blame]
/*
* BSD LICENSE
*
* Copyright(c) 2016-2017 Broadcom. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
*
* * Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* * Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in
* the documentation and/or other materials provided with the
* distribution.
* * Neither the name of Broadcom nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include "stingray.dtsi"
/ {
chosen {
stdout-path = "serial0:115200n8";
};
aliases {
serial0 = &uart1;
serial1 = &uart0;
serial2 = &uart2;
serial3 = &uart3;
};
sdio0_vddo_ctrl_reg: sdio0_vddo_ctrl {
compatible = "regulator-gpio";
regulator-name = "sdio0_vddo_ctrl_reg";
regulator-type = "voltage";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&pca9505 18 0>;
states = <3300000 0x0
1800000 0x1>;
};
sdio1_vddo_ctrl_reg: sdio1_vddo_ctrl {
compatible = "regulator-gpio";
regulator-name = "sdio1_vddo_ctrl_reg";
regulator-type = "voltage";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&pca9505 19 0>;
states = <3300000 0x0
1800000 0x1>;
};
};
&memory { /* Default DRAM banks */
reg = <0x00000000 0x80000000 0x0 0x80000000>, /* 2G @ 2G */
<0x00000008 0x80000000 0x1 0x80000000>; /* 6G @ 34G */
};
&sata0 {
status = "okay";
};
&sata_phy0{
status = "okay";
};
&sata1 {
status = "okay";
};
&sata_phy1{
status = "okay";
};
&sata2 {
status = "okay";
};
&sata_phy2{
status = "okay";
};
&sata3 {
status = "okay";
};
&sata_phy3{
status = "okay";
};
&sata4 {
status = "okay";
};
&sata_phy4{
status = "okay";
};
&sata5 {
status = "okay";
};
&sata_phy5{
status = "okay";
};
&sata6 {
status = "okay";
};
&sata_phy6{
status = "okay";
};
&sata7 {
status = "okay";
};
&sata_phy7{
status = "okay";
};
&mdio_mux_iproc {
mdio@10 {
gphy0: eth-phy@10 {
reg = <0x10>;
};
};
};
&uart1 {
status = "okay";
};
&pwm {
status = "okay";
};
&i2c0 {
status = "okay";
pca9505: pca9505@20 {
compatible = "nxp,pca9505";
gpio-controller;
#gpio-cells = <2>;
reg = <0x20>;
};
};
&i2c1 {
status = "okay";
pcf8574: pcf8574@20 {
compatible = "nxp,pcf8574a";
gpio-controller;
#gpio-cells = <2>;
reg = <0x27>;
};
};
&enet {
phy-mode = "rgmii-id";
phy-handle = <&gphy0>;
status = "okay";
};
&nand {
status = "ok";
nandcs@0 {
compatible = "brcm,nandcs";
reg = <0>;
nand-ecc-mode = "hw";
nand-ecc-strength = <8>;
nand-ecc-step-size = <512>;
nand-bus-width = <16>;
brcm,nand-oob-sector-size = <16>;
#address-cells = <1>;
#size-cells = <1>;
};
};
&sdio0 {
vqmmc-supply = <&sdio0_vddo_ctrl_reg>;
non-removable;
full-pwr-cycle;
status = "okay";
};
&sdio1 {
vqmmc-supply = <&sdio1_vddo_ctrl_reg>;
full-pwr-cycle;
status = "okay";
};