| /* | |
| * The following devices are accessible using this driver using | |
| * GPIO_MAJOR (120) and a couple of minor numbers. | |
| * | |
| * For ETRAX 100LX (CONFIG_ETRAX_ARCH_V10): | |
| * /dev/gpioa minor 0, 8 bit GPIO, each bit can change direction | |
| * /dev/gpiob minor 1, 8 bit GPIO, each bit can change direction | |
| * /dev/leds minor 2, Access to leds depending on kernelconfig | |
| * /dev/gpiog minor 3 | |
| * g0dir, g8_15dir, g16_23dir, g24 dir configurable in R_GEN_CONFIG | |
| * g1-g7 and g25-g31 is both input and outputs but on different pins | |
| * Also note that some bits change pins depending on what interfaces | |
| * are enabled. | |
| */ | |
| #ifndef _ASM_ETRAXGPIO_H | |
| #define _ASM_ETRAXGPIO_H | |
| #define GPIO_MINOR_FIRST 0 | |
| #define ETRAXGPIO_IOCTYPE 43 | |
| /* etraxgpio _IOC_TYPE, bits 8 to 15 in ioctl cmd */ | |
| #define GPIO_MINOR_A 0 | |
| #define GPIO_MINOR_B 1 | |
| #define GPIO_MINOR_LEDS 2 | |
| #define GPIO_MINOR_G 3 | |
| #define GPIO_MINOR_LAST 3 | |
| #define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST | |
| /* supported ioctl _IOC_NR's */ | |
| #define IO_READBITS 0x1 /* read and return current port bits (obsolete) */ | |
| #define IO_SETBITS 0x2 /* set the bits marked by 1 in the argument */ | |
| #define IO_CLRBITS 0x3 /* clear the bits marked by 1 in the argument */ | |
| /* the alarm is waited for by select() */ | |
| #define IO_HIGHALARM 0x4 /* set alarm on high for bits marked by 1 */ | |
| #define IO_LOWALARM 0x5 /* set alarm on low for bits marked by 1 */ | |
| #define IO_CLRALARM 0x6 /* clear alarm for bits marked by 1 */ | |
| /* LED ioctl */ | |
| #define IO_LEDACTIVE_SET 0x7 /* set active led | |
| * 0=off, 1=green, 2=red, 3=yellow */ | |
| /* GPIO direction ioctl's */ | |
| #define IO_READDIR 0x8 /* Read direction 0=input 1=output (obsolete) */ | |
| #define IO_SETINPUT 0x9 /* Set direction for bits set, 0=unchanged 1=input, | |
| returns mask with current inputs (obsolete) */ | |
| #define IO_SETOUTPUT 0xA /* Set direction for bits set, 0=unchanged 1=output, | |
| returns mask with current outputs (obsolete)*/ | |
| /* LED ioctl extended */ | |
| #define IO_LED_SETBIT 0xB | |
| #define IO_LED_CLRBIT 0xC | |
| /* SHUTDOWN ioctl */ | |
| #define IO_SHUTDOWN 0xD | |
| #define IO_GET_PWR_BT 0xE | |
| /* Bit toggling in driver settings */ | |
| /* bit set in low byte0 is CLK mask (0x00FF), | |
| bit set in byte1 is DATA mask (0xFF00) | |
| msb, data_mask[7:0] , clk_mask[7:0] | |
| */ | |
| #define IO_CFG_WRITE_MODE 0xF | |
| #define IO_CFG_WRITE_MODE_VALUE(msb, data_mask, clk_mask) \ | |
| ( (((msb)&1) << 16) | (((data_mask) &0xFF) << 8) | ((clk_mask) & 0xFF) ) | |
| /* The following 4 ioctl's take a pointer as argument and handles | |
| * 32 bit ports (port G) properly. | |
| * These replaces IO_READBITS,IO_SETINPUT AND IO_SETOUTPUT | |
| */ | |
| #define IO_READ_INBITS 0x10 /* *arg is result of reading the input pins */ | |
| #define IO_READ_OUTBITS 0x11 /* *arg is result of reading the output shadow */ | |
| #define IO_SETGET_INPUT 0x12 /* bits set in *arg is set to input, */ | |
| /* *arg updated with current input pins. */ | |
| #define IO_SETGET_OUTPUT 0x13 /* bits set in *arg is set to output, */ | |
| /* *arg updated with current output pins. */ | |
| #endif |