| / { | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| compatible = "brcm,bcm7346"; | |
| cpus { | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| mips-hpt-frequency = <163125000>; | |
| cpu@0 { | |
| compatible = "brcm,bmips5000"; | |
| device_type = "cpu"; | |
| reg = <0>; | |
| }; | |
| cpu@1 { | |
| compatible = "brcm,bmips5000"; | |
| device_type = "cpu"; | |
| reg = <1>; | |
| }; | |
| }; | |
| aliases { | |
| uart0 = &uart0; | |
| }; | |
| cpu_intc: interrupt-controller { | |
| #address-cells = <0>; | |
| compatible = "mti,cpu-interrupt-controller"; | |
| interrupt-controller; | |
| #interrupt-cells = <1>; | |
| }; | |
| clocks { | |
| uart_clk: uart_clk { | |
| compatible = "fixed-clock"; | |
| #clock-cells = <0>; | |
| clock-frequency = <81000000>; | |
| }; | |
| upg_clk: upg_clk { | |
| compatible = "fixed-clock"; | |
| #clock-cells = <0>; | |
| clock-frequency = <27000000>; | |
| }; | |
| }; | |
| rdb { | |
| #address-cells = <1>; | |
| #size-cells = <1>; | |
| compatible = "simple-bus"; | |
| ranges = <0 0x10000000 0x01000000>; | |
| periph_intc: interrupt-controller@411400 { | |
| compatible = "brcm,bcm7038-l1-intc"; | |
| reg = <0x411400 0x30>, <0x411600 0x30>; | |
| interrupt-controller; | |
| #interrupt-cells = <1>; | |
| interrupt-parent = <&cpu_intc>; | |
| interrupts = <2>, <3>; | |
| }; | |
| sun_l2_intc: interrupt-controller@403000 { | |
| compatible = "brcm,l2-intc"; | |
| reg = <0x403000 0x30>; | |
| interrupt-controller; | |
| #interrupt-cells = <1>; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <51>; | |
| }; | |
| gisb-arb@400000 { | |
| compatible = "brcm,bcm7400-gisb-arb"; | |
| reg = <0x400000 0xdc>; | |
| native-endian; | |
| interrupt-parent = <&sun_l2_intc>; | |
| interrupts = <0>, <2>; | |
| brcm,gisb-arb-master-mask = <0x673>; | |
| brcm,gisb-arb-master-names = "ssp_0", "cpu_0", "bsp_0", | |
| "rdc_0", "raaga_0", | |
| "jtag_0", "svd_0"; | |
| }; | |
| upg_irq0_intc: interrupt-controller@406780 { | |
| compatible = "brcm,bcm7120-l2-intc"; | |
| reg = <0x406780 0x8>; | |
| brcm,int-map-mask = <0x44>, <0xf000000>; | |
| brcm,int-fwd-mask = <0x70000>; | |
| interrupt-controller; | |
| #interrupt-cells = <1>; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <59>, <57>; | |
| interrupt-names = "upg_main", "upg_bsc"; | |
| }; | |
| upg_aon_irq0_intc: interrupt-controller@408b80 { | |
| compatible = "brcm,bcm7120-l2-intc"; | |
| reg = <0x408b80 0x8>; | |
| brcm,int-map-mask = <0x40>, <0x8000000>, <0x100000>; | |
| brcm,int-fwd-mask = <0>; | |
| brcm,irq-can-wake; | |
| interrupt-controller; | |
| #interrupt-cells = <1>; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <60>, <58>, <62>; | |
| interrupt-names = "upg_main_aon", "upg_bsc_aon", | |
| "upg_spi"; | |
| }; | |
| sun_top_ctrl: syscon@404000 { | |
| compatible = "brcm,bcm7346-sun-top-ctrl", "syscon"; | |
| reg = <0x404000 0x51c>; | |
| native-endian; | |
| }; | |
| reboot { | |
| compatible = "brcm,brcmstb-reboot"; | |
| syscon = <&sun_top_ctrl 0x304 0x308>; | |
| }; | |
| uart0: serial@406900 { | |
| compatible = "ns16550a"; | |
| reg = <0x406900 0x20>; | |
| reg-io-width = <0x4>; | |
| reg-shift = <0x2>; | |
| native-endian; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <64>; | |
| clocks = <&uart_clk>; | |
| status = "disabled"; | |
| }; | |
| uart1: serial@406940 { | |
| compatible = "ns16550a"; | |
| reg = <0x406940 0x20>; | |
| reg-io-width = <0x4>; | |
| reg-shift = <0x2>; | |
| native-endian; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <65>; | |
| clocks = <&uart_clk>; | |
| status = "disabled"; | |
| }; | |
| uart2: serial@406980 { | |
| compatible = "ns16550a"; | |
| reg = <0x406980 0x20>; | |
| reg-io-width = <0x4>; | |
| reg-shift = <0x2>; | |
| native-endian; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <66>; | |
| clocks = <&uart_clk>; | |
| status = "disabled"; | |
| }; | |
| bsca: i2c@406200 { | |
| clock-frequency = <390000>; | |
| compatible = "brcm,brcmstb-i2c"; | |
| interrupt-parent = <&upg_irq0_intc>; | |
| reg = <0x406200 0x58>; | |
| interrupts = <24>; | |
| interrupt-names = "upg_bsca"; | |
| status = "disabled"; | |
| }; | |
| bscb: i2c@406280 { | |
| clock-frequency = <390000>; | |
| compatible = "brcm,brcmstb-i2c"; | |
| interrupt-parent = <&upg_irq0_intc>; | |
| reg = <0x406280 0x58>; | |
| interrupts = <25>; | |
| interrupt-names = "upg_bscb"; | |
| status = "disabled"; | |
| }; | |
| bscc: i2c@406300 { | |
| clock-frequency = <390000>; | |
| compatible = "brcm,brcmstb-i2c"; | |
| interrupt-parent = <&upg_irq0_intc>; | |
| reg = <0x406300 0x58>; | |
| interrupts = <26>; | |
| interrupt-names = "upg_bscc"; | |
| status = "disabled"; | |
| }; | |
| bscd: i2c@406380 { | |
| clock-frequency = <390000>; | |
| compatible = "brcm,brcmstb-i2c"; | |
| interrupt-parent = <&upg_irq0_intc>; | |
| reg = <0x406380 0x58>; | |
| interrupts = <27>; | |
| interrupt-names = "upg_bscd"; | |
| status = "disabled"; | |
| }; | |
| bsce: i2c@408980 { | |
| clock-frequency = <390000>; | |
| compatible = "brcm,brcmstb-i2c"; | |
| interrupt-parent = <&upg_aon_irq0_intc>; | |
| reg = <0x408980 0x58>; | |
| interrupts = <27>; | |
| interrupt-names = "upg_bsce"; | |
| status = "disabled"; | |
| }; | |
| pwma: pwm@406580 { | |
| compatible = "brcm,bcm7038-pwm"; | |
| reg = <0x406580 0x28>; | |
| #pwm-cells = <2>; | |
| clocks = <&upg_clk>; | |
| status = "disabled"; | |
| }; | |
| pwmb: pwm@406800 { | |
| compatible = "brcm,bcm7038-pwm"; | |
| reg = <0x406800 0x28>; | |
| #pwm-cells = <2>; | |
| clocks = <&upg_clk>; | |
| status = "disabled"; | |
| }; | |
| aon_pm_l2_intc: interrupt-controller@408440 { | |
| compatible = "brcm,l2-intc"; | |
| reg = <0x408440 0x30>; | |
| interrupt-controller; | |
| #interrupt-cells = <1>; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <53>; | |
| brcm,irq-can-wake; | |
| }; | |
| upg_gio: gpio@406700 { | |
| compatible = "brcm,brcmstb-gpio"; | |
| reg = <0x406700 0x60>; | |
| #gpio-cells = <2>; | |
| #interrupt-cells = <2>; | |
| gpio-controller; | |
| interrupt-controller; | |
| interrupt-parent = <&upg_irq0_intc>; | |
| interrupts = <6>; | |
| brcm,gpio-bank-widths = <32 32 16>; | |
| }; | |
| upg_gio_aon: gpio@408c00 { | |
| compatible = "brcm,brcmstb-gpio"; | |
| reg = <0x408c00 0x60>; | |
| #gpio-cells = <2>; | |
| #interrupt-cells = <2>; | |
| gpio-controller; | |
| interrupt-controller; | |
| interrupt-parent = <&upg_aon_irq0_intc>; | |
| interrupts = <6>; | |
| interrupts-extended = <&upg_aon_irq0_intc 6>, | |
| <&aon_pm_l2_intc 5>; | |
| wakeup-source; | |
| brcm,gpio-bank-widths = <27 32 2>; | |
| }; | |
| enet0: ethernet@430000 { | |
| phy-mode = "internal"; | |
| phy-handle = <&phy1>; | |
| mac-address = [ 00 10 18 36 23 1a ]; | |
| compatible = "brcm,genet-v2"; | |
| #address-cells = <0x1>; | |
| #size-cells = <0x1>; | |
| reg = <0x430000 0x4c8c>; | |
| interrupts = <24>, <25>; | |
| interrupt-parent = <&periph_intc>; | |
| status = "disabled"; | |
| mdio@e14 { | |
| compatible = "brcm,genet-mdio-v2"; | |
| #address-cells = <0x1>; | |
| #size-cells = <0x0>; | |
| reg = <0xe14 0x8>; | |
| phy1: ethernet-phy@1 { | |
| max-speed = <100>; | |
| reg = <0x1>; | |
| compatible = "brcm,40nm-ephy", | |
| "ethernet-phy-ieee802.3-c22"; | |
| }; | |
| }; | |
| }; | |
| ehci0: usb@480300 { | |
| compatible = "brcm,bcm7346-ehci", "generic-ehci"; | |
| reg = <0x480300 0x100>; | |
| native-endian; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <68>; | |
| status = "disabled"; | |
| }; | |
| ohci0: usb@480400 { | |
| compatible = "brcm,bcm7346-ohci", "generic-ohci"; | |
| reg = <0x480400 0x100>; | |
| native-endian; | |
| no-big-frame-no; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <70>; | |
| status = "disabled"; | |
| }; | |
| ehci1: usb@480500 { | |
| compatible = "brcm,bcm7346-ehci", "generic-ehci"; | |
| reg = <0x480500 0x100>; | |
| native-endian; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <69>; | |
| status = "disabled"; | |
| }; | |
| ohci1: usb@480600 { | |
| compatible = "brcm,bcm7346-ohci", "generic-ohci"; | |
| reg = <0x480600 0x100>; | |
| native-endian; | |
| no-big-frame-no; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <71>; | |
| status = "disabled"; | |
| }; | |
| ehci2: usb@490300 { | |
| compatible = "brcm,bcm7346-ehci", "generic-ehci"; | |
| reg = <0x490300 0x100>; | |
| native-endian; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <73>; | |
| status = "disabled"; | |
| }; | |
| ohci2: usb@490400 { | |
| compatible = "brcm,bcm7346-ohci", "generic-ohci"; | |
| reg = <0x490400 0x100>; | |
| native-endian; | |
| no-big-frame-no; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <75>; | |
| status = "disabled"; | |
| }; | |
| ehci3: usb@490500 { | |
| compatible = "brcm,bcm7346-ehci", "generic-ehci"; | |
| reg = <0x490500 0x100>; | |
| native-endian; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <74>; | |
| status = "disabled"; | |
| }; | |
| ohci3: usb@490600 { | |
| compatible = "brcm,bcm7346-ohci", "generic-ohci"; | |
| reg = <0x490600 0x100>; | |
| native-endian; | |
| no-big-frame-no; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <76>; | |
| status = "disabled"; | |
| }; | |
| hif_l2_intc: interrupt-controller@411000 { | |
| compatible = "brcm,l2-intc"; | |
| reg = <0x411000 0x30>; | |
| interrupt-controller; | |
| #interrupt-cells = <1>; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <30>; | |
| }; | |
| nand: nand@412800 { | |
| compatible = "brcm,brcmnand-v5.0", "brcm,brcmnand"; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| reg-names = "nand"; | |
| reg = <0x412800 0x400>; | |
| interrupt-parent = <&hif_l2_intc>; | |
| interrupts = <24>; | |
| status = "disabled"; | |
| }; | |
| sata: sata@181000 { | |
| compatible = "brcm,bcm7425-ahci", "brcm,sata3-ahci"; | |
| reg-names = "ahci", "top-ctrl"; | |
| reg = <0x181000 0xa9c>, <0x180020 0x1c>; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <40>; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; | |
| sata0: sata-port@0 { | |
| reg = <0>; | |
| phys = <&sata_phy0>; | |
| }; | |
| sata1: sata-port@1 { | |
| reg = <1>; | |
| phys = <&sata_phy1>; | |
| }; | |
| }; | |
| sata_phy: sata-phy@180100 { | |
| compatible = "brcm,bcm7425-sata-phy", "brcm,phy-sata3"; | |
| reg = <0x180100 0x0eff>; | |
| reg-names = "phy"; | |
| #address-cells = <1>; | |
| #size-cells = <0>; | |
| status = "disabled"; | |
| sata_phy0: sata-phy@0 { | |
| reg = <0>; | |
| #phy-cells = <0>; | |
| }; | |
| sata_phy1: sata-phy@1 { | |
| reg = <1>; | |
| #phy-cells = <0>; | |
| }; | |
| }; | |
| sdhci0: sdhci@413500 { | |
| compatible = "brcm,bcm7425-sdhci"; | |
| reg = <0x413500 0x100>; | |
| interrupt-parent = <&periph_intc>; | |
| interrupts = <85>; | |
| status = "disabled"; | |
| }; | |
| }; | |
| }; |