| /* | |
| * drivers/dma/imx-sdma.c | |
| * | |
| * This file contains a driver for the Freescale Smart DMA engine | |
| * | |
| * Copyright 2010 Sascha Hauer, Pengutronix <s.hauer@pengutronix.de> | |
| * | |
| * Based on code from Freescale: | |
| * | |
| * Copyright 2004-2009 Freescale Semiconductor, Inc. All Rights Reserved. | |
| * | |
| * The code contained herein is licensed under the GNU General Public | |
| * License. You may obtain a copy of the GNU General Public License | |
| * Version 2 or later at the following locations: | |
| * | |
| * http://www.opensource.org/licenses/gpl-license.html | |
| * http://www.gnu.org/copyleft/gpl.html | |
| */ | |
| #include <linux/init.h> | |
| #include <linux/iopoll.h> | |
| #include <linux/module.h> | |
| #include <linux/types.h> | |
| #include <linux/bitops.h> | |
| #include <linux/mm.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/clk.h> | |
| #include <linux/delay.h> | |
| #include <linux/sched.h> | |
| #include <linux/semaphore.h> | |
| #include <linux/spinlock.h> | |
| #include <linux/device.h> | |
| #include <linux/dma-mapping.h> | |
| #include <linux/firmware.h> | |
| #include <linux/slab.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/dmaengine.h> | |
| #include <linux/of.h> | |
| #include <linux/of_address.h> | |
| #include <linux/of_device.h> | |
| #include <linux/of_dma.h> | |
| #include <asm/irq.h> | |
| #include <linux/platform_data/dma-imx-sdma.h> | |
| #include <linux/platform_data/dma-imx.h> | |
| #include <linux/regmap.h> | |
| #include <linux/mfd/syscon.h> | |
| #include <linux/mfd/syscon/imx6q-iomuxc-gpr.h> | |
| #include "dmaengine.h" | |
| /* SDMA registers */ | |
| #define SDMA_H_C0PTR 0x000 | |
| #define SDMA_H_INTR 0x004 | |
| #define SDMA_H_STATSTOP 0x008 | |
| #define SDMA_H_START 0x00c | |
| #define SDMA_H_EVTOVR 0x010 | |
| #define SDMA_H_DSPOVR 0x014 | |
| #define SDMA_H_HOSTOVR 0x018 | |
| #define SDMA_H_EVTPEND 0x01c | |
| #define SDMA_H_DSPENBL 0x020 | |
| #define SDMA_H_RESET 0x024 | |
| #define SDMA_H_EVTERR 0x028 | |
| #define SDMA_H_INTRMSK 0x02c | |
| #define SDMA_H_PSW 0x030 | |
| #define SDMA_H_EVTERRDBG 0x034 | |
| #define SDMA_H_CONFIG 0x038 | |
| #define SDMA_ONCE_ENB 0x040 | |
| #define SDMA_ONCE_DATA 0x044 | |
| #define SDMA_ONCE_INSTR 0x048 | |
| #define SDMA_ONCE_STAT 0x04c | |
| #define SDMA_ONCE_CMD 0x050 | |
| #define SDMA_EVT_MIRROR 0x054 | |
| #define SDMA_ILLINSTADDR 0x058 | |
| #define SDMA_CHN0ADDR 0x05c | |
| #define SDMA_ONCE_RTB 0x060 | |
| #define SDMA_XTRIG_CONF1 0x070 | |
| #define SDMA_XTRIG_CONF2 0x074 | |
| #define SDMA_CHNENBL0_IMX35 0x200 | |
| #define SDMA_CHNENBL0_IMX31 0x080 | |
| #define SDMA_CHNPRI_0 0x100 | |
| /* | |
| * Buffer descriptor status values. | |
| */ | |
| #define BD_DONE 0x01 | |
| #define BD_WRAP 0x02 | |
| #define BD_CONT 0x04 | |
| #define BD_INTR 0x08 | |
| #define BD_RROR 0x10 | |
| #define BD_LAST 0x20 | |
| #define BD_EXTD 0x80 | |
| /* | |
| * Data Node descriptor status values. | |
| */ | |
| #define DND_END_OF_FRAME 0x80 | |
| #define DND_END_OF_XFER 0x40 | |
| #define DND_DONE 0x20 | |
| #define DND_UNUSED 0x01 | |
| /* | |
| * IPCV2 descriptor status values. | |
| */ | |
| #define BD_IPCV2_END_OF_FRAME 0x40 | |
| #define IPCV2_MAX_NODES 50 | |
| /* | |
| * Error bit set in the CCB status field by the SDMA, | |
| * in setbd routine, in case of a transfer error | |
| */ | |
| #define DATA_ERROR 0x10000000 | |
| /* | |
| * Buffer descriptor commands. | |
| */ | |
| #define C0_ADDR 0x01 | |
| #define C0_LOAD 0x02 | |
| #define C0_DUMP 0x03 | |
| #define C0_SETCTX 0x07 | |
| #define C0_GETCTX 0x03 | |
| #define C0_SETDM 0x01 | |
| #define C0_SETPM 0x04 | |
| #define C0_GETDM 0x02 | |
| #define C0_GETPM 0x08 | |
| /* | |
| * Change endianness indicator in the BD command field | |
| */ | |
| #define CHANGE_ENDIANNESS 0x80 | |
| /* | |
| * p_2_p watermark_level description | |
| * Bits Name Description | |
| * 0-7 Lower WML Lower watermark level | |
| * 8 PS 1: Pad Swallowing | |
| * 0: No Pad Swallowing | |
| * 9 PA 1: Pad Adding | |
| * 0: No Pad Adding | |
| * 10 SPDIF If this bit is set both source | |
| * and destination are on SPBA | |
| * 11 Source Bit(SP) 1: Source on SPBA | |
| * 0: Source on AIPS | |
| * 12 Destination Bit(DP) 1: Destination on SPBA | |
| * 0: Destination on AIPS | |
| * 13-15 --------- MUST BE 0 | |
| * 16-23 Higher WML HWML | |
| * 24-27 N Total number of samples after | |
| * which Pad adding/Swallowing | |
| * must be done. It must be odd. | |
| * 28 Lower WML Event(LWE) SDMA events reg to check for | |
| * LWML event mask | |
| * 0: LWE in EVENTS register | |
| * 1: LWE in EVENTS2 register | |
| * 29 Higher WML Event(HWE) SDMA events reg to check for | |
| * HWML event mask | |
| * 0: HWE in EVENTS register | |
| * 1: HWE in EVENTS2 register | |
| * 30 --------- MUST BE 0 | |
| * 31 CONT 1: Amount of samples to be | |
| * transferred is unknown and | |
| * script will keep on | |
| * transferring samples as long as | |
| * both events are detected and | |
| * script must be manually stopped | |
| * by the application | |
| * 0: The amount of samples to be | |
| * transferred is equal to the | |
| * count field of mode word | |
| */ | |
| #define SDMA_WATERMARK_LEVEL_LWML 0xFF | |
| #define SDMA_WATERMARK_LEVEL_PS BIT(8) | |
| #define SDMA_WATERMARK_LEVEL_PA BIT(9) | |
| #define SDMA_WATERMARK_LEVEL_SPDIF BIT(10) | |
| #define SDMA_WATERMARK_LEVEL_SP BIT(11) | |
| #define SDMA_WATERMARK_LEVEL_DP BIT(12) | |
| #define SDMA_WATERMARK_LEVEL_HWML (0xFF << 16) | |
| #define SDMA_WATERMARK_LEVEL_LWE BIT(28) | |
| #define SDMA_WATERMARK_LEVEL_HWE BIT(29) | |
| #define SDMA_WATERMARK_LEVEL_CONT BIT(31) | |
| /* | |
| * Mode/Count of data node descriptors - IPCv2 | |
| */ | |
| struct sdma_mode_count { | |
| u32 count : 16; /* size of the buffer pointed by this BD */ | |
| u32 status : 8; /* E,R,I,C,W,D status bits stored here */ | |
| u32 command : 8; /* command mostly used for channel 0 */ | |
| }; | |
| /* | |
| * Buffer descriptor | |
| */ | |
| struct sdma_buffer_descriptor { | |
| struct sdma_mode_count mode; | |
| u32 buffer_addr; /* address of the buffer described */ | |
| u32 ext_buffer_addr; /* extended buffer address */ | |
| } __attribute__ ((packed)); | |
| /** | |
| * struct sdma_channel_control - Channel control Block | |
| * | |
| * @current_bd_ptr current buffer descriptor processed | |
| * @base_bd_ptr first element of buffer descriptor array | |
| * @unused padding. The SDMA engine expects an array of 128 byte | |
| * control blocks | |
| */ | |
| struct sdma_channel_control { | |
| u32 current_bd_ptr; | |
| u32 base_bd_ptr; | |
| u32 unused[2]; | |
| } __attribute__ ((packed)); | |
| /** | |
| * struct sdma_state_registers - SDMA context for a channel | |
| * | |
| * @pc: program counter | |
| * @t: test bit: status of arithmetic & test instruction | |
| * @rpc: return program counter | |
| * @sf: source fault while loading data | |
| * @spc: loop start program counter | |
| * @df: destination fault while storing data | |
| * @epc: loop end program counter | |
| * @lm: loop mode | |
| */ | |
| struct sdma_state_registers { | |
| u32 pc :14; | |
| u32 unused1: 1; | |
| u32 t : 1; | |
| u32 rpc :14; | |
| u32 unused0: 1; | |
| u32 sf : 1; | |
| u32 spc :14; | |
| u32 unused2: 1; | |
| u32 df : 1; | |
| u32 epc :14; | |
| u32 lm : 2; | |
| } __attribute__ ((packed)); | |
| /** | |
| * struct sdma_context_data - sdma context specific to a channel | |
| * | |
| * @channel_state: channel state bits | |
| * @gReg: general registers | |
| * @mda: burst dma destination address register | |
| * @msa: burst dma source address register | |
| * @ms: burst dma status register | |
| * @md: burst dma data register | |
| * @pda: peripheral dma destination address register | |
| * @psa: peripheral dma source address register | |
| * @ps: peripheral dma status register | |
| * @pd: peripheral dma data register | |
| * @ca: CRC polynomial register | |
| * @cs: CRC accumulator register | |
| * @dda: dedicated core destination address register | |
| * @dsa: dedicated core source address register | |
| * @ds: dedicated core status register | |
| * @dd: dedicated core data register | |
| */ | |
| struct sdma_context_data { | |
| struct sdma_state_registers channel_state; | |
| u32 gReg[8]; | |
| u32 mda; | |
| u32 msa; | |
| u32 ms; | |
| u32 md; | |
| u32 pda; | |
| u32 psa; | |
| u32 ps; | |
| u32 pd; | |
| u32 ca; | |
| u32 cs; | |
| u32 dda; | |
| u32 dsa; | |
| u32 ds; | |
| u32 dd; | |
| u32 scratch0; | |
| u32 scratch1; | |
| u32 scratch2; | |
| u32 scratch3; | |
| u32 scratch4; | |
| u32 scratch5; | |
| u32 scratch6; | |
| u32 scratch7; | |
| } __attribute__ ((packed)); | |
| #define NUM_BD (int)(PAGE_SIZE / sizeof(struct sdma_buffer_descriptor)) | |
| struct sdma_engine; | |
| /** | |
| * struct sdma_channel - housekeeping for a SDMA channel | |
| * | |
| * @sdma pointer to the SDMA engine for this channel | |
| * @channel the channel number, matches dmaengine chan_id + 1 | |
| * @direction transfer type. Needed for setting SDMA script | |
| * @peripheral_type Peripheral type. Needed for setting SDMA script | |
| * @event_id0 aka dma request line | |
| * @event_id1 for channels that use 2 events | |
| * @word_size peripheral access size | |
| * @buf_tail ID of the buffer that was processed | |
| * @num_bd max NUM_BD. number of descriptors currently handling | |
| */ | |
| struct sdma_channel { | |
| struct sdma_engine *sdma; | |
| unsigned int channel; | |
| enum dma_transfer_direction direction; | |
| enum sdma_peripheral_type peripheral_type; | |
| unsigned int event_id0; | |
| unsigned int event_id1; | |
| enum dma_slave_buswidth word_size; | |
| unsigned int buf_tail; | |
| unsigned int num_bd; | |
| unsigned int period_len; | |
| struct sdma_buffer_descriptor *bd; | |
| dma_addr_t bd_phys; | |
| unsigned int pc_from_device, pc_to_device; | |
| unsigned int device_to_device; | |
| unsigned long flags; | |
| dma_addr_t per_address, per_address2; | |
| unsigned long event_mask[2]; | |
| unsigned long watermark_level; | |
| u32 shp_addr, per_addr; | |
| struct dma_chan chan; | |
| spinlock_t lock; | |
| struct dma_async_tx_descriptor desc; | |
| enum dma_status status; | |
| unsigned int chn_count; | |
| unsigned int chn_real_count; | |
| struct tasklet_struct tasklet; | |
| struct imx_dma_data data; | |
| }; | |
| #define IMX_DMA_SG_LOOP BIT(0) | |
| #define MAX_DMA_CHANNELS 32 | |
| #define MXC_SDMA_DEFAULT_PRIORITY 1 | |
| #define MXC_SDMA_MIN_PRIORITY 1 | |
| #define MXC_SDMA_MAX_PRIORITY 7 | |
| #define SDMA_FIRMWARE_MAGIC 0x414d4453 | |
| /** | |
| * struct sdma_firmware_header - Layout of the firmware image | |
| * | |
| * @magic "SDMA" | |
| * @version_major increased whenever layout of struct sdma_script_start_addrs | |
| * changes. | |
| * @version_minor firmware minor version (for binary compatible changes) | |
| * @script_addrs_start offset of struct sdma_script_start_addrs in this image | |
| * @num_script_addrs Number of script addresses in this image | |
| * @ram_code_start offset of SDMA ram image in this firmware image | |
| * @ram_code_size size of SDMA ram image | |
| * @script_addrs Stores the start address of the SDMA scripts | |
| * (in SDMA memory space) | |
| */ | |
| struct sdma_firmware_header { | |
| u32 magic; | |
| u32 version_major; | |
| u32 version_minor; | |
| u32 script_addrs_start; | |
| u32 num_script_addrs; | |
| u32 ram_code_start; | |
| u32 ram_code_size; | |
| }; | |
| struct sdma_driver_data { | |
| int chnenbl0; | |
| int num_events; | |
| struct sdma_script_start_addrs *script_addrs; | |
| }; | |
| struct sdma_engine { | |
| struct device *dev; | |
| struct device_dma_parameters dma_parms; | |
| struct sdma_channel channel[MAX_DMA_CHANNELS]; | |
| struct sdma_channel_control *channel_control; | |
| void __iomem *regs; | |
| struct sdma_context_data *context; | |
| dma_addr_t context_phys; | |
| struct dma_device dma_device; | |
| struct clk *clk_ipg; | |
| struct clk *clk_ahb; | |
| spinlock_t channel_0_lock; | |
| u32 script_number; | |
| struct sdma_script_start_addrs *script_addrs; | |
| const struct sdma_driver_data *drvdata; | |
| u32 spba_start_addr; | |
| u32 spba_end_addr; | |
| unsigned int irq; | |
| }; | |
| static struct sdma_driver_data sdma_imx31 = { | |
| .chnenbl0 = SDMA_CHNENBL0_IMX31, | |
| .num_events = 32, | |
| }; | |
| static struct sdma_script_start_addrs sdma_script_imx25 = { | |
| .ap_2_ap_addr = 729, | |
| .uart_2_mcu_addr = 904, | |
| .per_2_app_addr = 1255, | |
| .mcu_2_app_addr = 834, | |
| .uartsh_2_mcu_addr = 1120, | |
| .per_2_shp_addr = 1329, | |
| .mcu_2_shp_addr = 1048, | |
| .ata_2_mcu_addr = 1560, | |
| .mcu_2_ata_addr = 1479, | |
| .app_2_per_addr = 1189, | |
| .app_2_mcu_addr = 770, | |
| .shp_2_per_addr = 1407, | |
| .shp_2_mcu_addr = 979, | |
| }; | |
| static struct sdma_driver_data sdma_imx25 = { | |
| .chnenbl0 = SDMA_CHNENBL0_IMX35, | |
| .num_events = 48, | |
| .script_addrs = &sdma_script_imx25, | |
| }; | |
| static struct sdma_driver_data sdma_imx35 = { | |
| .chnenbl0 = SDMA_CHNENBL0_IMX35, | |
| .num_events = 48, | |
| }; | |
| static struct sdma_script_start_addrs sdma_script_imx51 = { | |
| .ap_2_ap_addr = 642, | |
| .uart_2_mcu_addr = 817, | |
| .mcu_2_app_addr = 747, | |
| .mcu_2_shp_addr = 961, | |
| .ata_2_mcu_addr = 1473, | |
| .mcu_2_ata_addr = 1392, | |
| .app_2_per_addr = 1033, | |
| .app_2_mcu_addr = 683, | |
| .shp_2_per_addr = 1251, | |
| .shp_2_mcu_addr = 892, | |
| }; | |
| static struct sdma_driver_data sdma_imx51 = { | |
| .chnenbl0 = SDMA_CHNENBL0_IMX35, | |
| .num_events = 48, | |
| .script_addrs = &sdma_script_imx51, | |
| }; | |
| static struct sdma_script_start_addrs sdma_script_imx53 = { | |
| .ap_2_ap_addr = 642, | |
| .app_2_mcu_addr = 683, | |
| .mcu_2_app_addr = 747, | |
| .uart_2_mcu_addr = 817, | |
| .shp_2_mcu_addr = 891, | |
| .mcu_2_shp_addr = 960, | |
| .uartsh_2_mcu_addr = 1032, | |
| .spdif_2_mcu_addr = 1100, | |
| .mcu_2_spdif_addr = 1134, | |
| .firi_2_mcu_addr = 1193, | |
| .mcu_2_firi_addr = 1290, | |
| }; | |
| static struct sdma_driver_data sdma_imx53 = { | |
| .chnenbl0 = SDMA_CHNENBL0_IMX35, | |
| .num_events = 48, | |
| .script_addrs = &sdma_script_imx53, | |
| }; | |
| static struct sdma_script_start_addrs sdma_script_imx6q = { | |
| .ap_2_ap_addr = 642, | |
| .uart_2_mcu_addr = 817, | |
| .mcu_2_app_addr = 747, | |
| .per_2_per_addr = 6331, | |
| .uartsh_2_mcu_addr = 1032, | |
| .mcu_2_shp_addr = 960, | |
| .app_2_mcu_addr = 683, | |
| .shp_2_mcu_addr = 891, | |
| .spdif_2_mcu_addr = 1100, | |
| .mcu_2_spdif_addr = 1134, | |
| }; | |
| static struct sdma_driver_data sdma_imx6q = { | |
| .chnenbl0 = SDMA_CHNENBL0_IMX35, | |
| .num_events = 48, | |
| .script_addrs = &sdma_script_imx6q, | |
| }; | |
| static struct sdma_script_start_addrs sdma_script_imx7d = { | |
| .ap_2_ap_addr = 644, | |
| .uart_2_mcu_addr = 819, | |
| .mcu_2_app_addr = 749, | |
| .uartsh_2_mcu_addr = 1034, | |
| .mcu_2_shp_addr = 962, | |
| .app_2_mcu_addr = 685, | |
| .shp_2_mcu_addr = 893, | |
| .spdif_2_mcu_addr = 1102, | |
| .mcu_2_spdif_addr = 1136, | |
| }; | |
| static struct sdma_driver_data sdma_imx7d = { | |
| .chnenbl0 = SDMA_CHNENBL0_IMX35, | |
| .num_events = 48, | |
| .script_addrs = &sdma_script_imx7d, | |
| }; | |
| static const struct platform_device_id sdma_devtypes[] = { | |
| { | |
| .name = "imx25-sdma", | |
| .driver_data = (unsigned long)&sdma_imx25, | |
| }, { | |
| .name = "imx31-sdma", | |
| .driver_data = (unsigned long)&sdma_imx31, | |
| }, { | |
| .name = "imx35-sdma", | |
| .driver_data = (unsigned long)&sdma_imx35, | |
| }, { | |
| .name = "imx51-sdma", | |
| .driver_data = (unsigned long)&sdma_imx51, | |
| }, { | |
| .name = "imx53-sdma", | |
| .driver_data = (unsigned long)&sdma_imx53, | |
| }, { | |
| .name = "imx6q-sdma", | |
| .driver_data = (unsigned long)&sdma_imx6q, | |
| }, { | |
| .name = "imx7d-sdma", | |
| .driver_data = (unsigned long)&sdma_imx7d, | |
| }, { | |
| /* sentinel */ | |
| } | |
| }; | |
| MODULE_DEVICE_TABLE(platform, sdma_devtypes); | |
| static const struct of_device_id sdma_dt_ids[] = { | |
| { .compatible = "fsl,imx6q-sdma", .data = &sdma_imx6q, }, | |
| { .compatible = "fsl,imx53-sdma", .data = &sdma_imx53, }, | |
| { .compatible = "fsl,imx51-sdma", .data = &sdma_imx51, }, | |
| { .compatible = "fsl,imx35-sdma", .data = &sdma_imx35, }, | |
| { .compatible = "fsl,imx31-sdma", .data = &sdma_imx31, }, | |
| { .compatible = "fsl,imx25-sdma", .data = &sdma_imx25, }, | |
| { .compatible = "fsl,imx7d-sdma", .data = &sdma_imx7d, }, | |
| { /* sentinel */ } | |
| }; | |
| MODULE_DEVICE_TABLE(of, sdma_dt_ids); | |
| #define SDMA_H_CONFIG_DSPDMA BIT(12) /* indicates if the DSPDMA is used */ | |
| #define SDMA_H_CONFIG_RTD_PINS BIT(11) /* indicates if Real-Time Debug pins are enabled */ | |
| #define SDMA_H_CONFIG_ACR BIT(4) /* indicates if AHB freq /core freq = 2 or 1 */ | |
| #define SDMA_H_CONFIG_CSM (3) /* indicates which context switch mode is selected*/ | |
| static inline u32 chnenbl_ofs(struct sdma_engine *sdma, unsigned int event) | |
| { | |
| u32 chnenbl0 = sdma->drvdata->chnenbl0; | |
| return chnenbl0 + event * 4; | |
| } | |
| static int sdma_config_ownership(struct sdma_channel *sdmac, | |
| bool event_override, bool mcu_override, bool dsp_override) | |
| { | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| int channel = sdmac->channel; | |
| unsigned long evt, mcu, dsp; | |
| if (event_override && mcu_override && dsp_override) | |
| return -EINVAL; | |
| evt = readl_relaxed(sdma->regs + SDMA_H_EVTOVR); | |
| mcu = readl_relaxed(sdma->regs + SDMA_H_HOSTOVR); | |
| dsp = readl_relaxed(sdma->regs + SDMA_H_DSPOVR); | |
| if (dsp_override) | |
| __clear_bit(channel, &dsp); | |
| else | |
| __set_bit(channel, &dsp); | |
| if (event_override) | |
| __clear_bit(channel, &evt); | |
| else | |
| __set_bit(channel, &evt); | |
| if (mcu_override) | |
| __clear_bit(channel, &mcu); | |
| else | |
| __set_bit(channel, &mcu); | |
| writel_relaxed(evt, sdma->regs + SDMA_H_EVTOVR); | |
| writel_relaxed(mcu, sdma->regs + SDMA_H_HOSTOVR); | |
| writel_relaxed(dsp, sdma->regs + SDMA_H_DSPOVR); | |
| return 0; | |
| } | |
| static void sdma_enable_channel(struct sdma_engine *sdma, int channel) | |
| { | |
| writel(BIT(channel), sdma->regs + SDMA_H_START); | |
| } | |
| /* | |
| * sdma_run_channel0 - run a channel and wait till it's done | |
| */ | |
| static int sdma_run_channel0(struct sdma_engine *sdma) | |
| { | |
| int ret; | |
| u32 reg; | |
| sdma_enable_channel(sdma, 0); | |
| ret = readl_relaxed_poll_timeout_atomic(sdma->regs + SDMA_H_STATSTOP, | |
| reg, !(reg & 1), 1, 500); | |
| if (ret) | |
| dev_err(sdma->dev, "Timeout waiting for CH0 ready\n"); | |
| /* Set bits of CONFIG register with dynamic context switching */ | |
| if (readl(sdma->regs + SDMA_H_CONFIG) == 0) | |
| writel_relaxed(SDMA_H_CONFIG_CSM, sdma->regs + SDMA_H_CONFIG); | |
| return ret; | |
| } | |
| static int sdma_load_script(struct sdma_engine *sdma, void *buf, int size, | |
| u32 address) | |
| { | |
| struct sdma_buffer_descriptor *bd0 = sdma->channel[0].bd; | |
| void *buf_virt; | |
| dma_addr_t buf_phys; | |
| int ret; | |
| unsigned long flags; | |
| buf_virt = dma_alloc_coherent(NULL, | |
| size, | |
| &buf_phys, GFP_KERNEL); | |
| if (!buf_virt) { | |
| return -ENOMEM; | |
| } | |
| spin_lock_irqsave(&sdma->channel_0_lock, flags); | |
| bd0->mode.command = C0_SETPM; | |
| bd0->mode.status = BD_DONE | BD_INTR | BD_WRAP | BD_EXTD; | |
| bd0->mode.count = size / 2; | |
| bd0->buffer_addr = buf_phys; | |
| bd0->ext_buffer_addr = address; | |
| memcpy(buf_virt, buf, size); | |
| ret = sdma_run_channel0(sdma); | |
| spin_unlock_irqrestore(&sdma->channel_0_lock, flags); | |
| dma_free_coherent(NULL, size, buf_virt, buf_phys); | |
| return ret; | |
| } | |
| static void sdma_event_enable(struct sdma_channel *sdmac, unsigned int event) | |
| { | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| int channel = sdmac->channel; | |
| unsigned long val; | |
| u32 chnenbl = chnenbl_ofs(sdma, event); | |
| val = readl_relaxed(sdma->regs + chnenbl); | |
| __set_bit(channel, &val); | |
| writel_relaxed(val, sdma->regs + chnenbl); | |
| } | |
| static void sdma_event_disable(struct sdma_channel *sdmac, unsigned int event) | |
| { | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| int channel = sdmac->channel; | |
| u32 chnenbl = chnenbl_ofs(sdma, event); | |
| unsigned long val; | |
| val = readl_relaxed(sdma->regs + chnenbl); | |
| __clear_bit(channel, &val); | |
| writel_relaxed(val, sdma->regs + chnenbl); | |
| } | |
| static void sdma_update_channel_loop(struct sdma_channel *sdmac) | |
| { | |
| struct sdma_buffer_descriptor *bd; | |
| int error = 0; | |
| enum dma_status old_status = sdmac->status; | |
| /* | |
| * loop mode. Iterate over descriptors, re-setup them and | |
| * call callback function. | |
| */ | |
| while (1) { | |
| bd = &sdmac->bd[sdmac->buf_tail]; | |
| if (bd->mode.status & BD_DONE) | |
| break; | |
| if (bd->mode.status & BD_RROR) { | |
| bd->mode.status &= ~BD_RROR; | |
| sdmac->status = DMA_ERROR; | |
| error = -EIO; | |
| } | |
| /* | |
| * We use bd->mode.count to calculate the residue, since contains | |
| * the number of bytes present in the current buffer descriptor. | |
| */ | |
| sdmac->chn_real_count = bd->mode.count; | |
| bd->mode.status |= BD_DONE; | |
| bd->mode.count = sdmac->period_len; | |
| /* | |
| * The callback is called from the interrupt context in order | |
| * to reduce latency and to avoid the risk of altering the | |
| * SDMA transaction status by the time the client tasklet is | |
| * executed. | |
| */ | |
| dmaengine_desc_get_callback_invoke(&sdmac->desc, NULL); | |
| sdmac->buf_tail++; | |
| sdmac->buf_tail %= sdmac->num_bd; | |
| if (error) | |
| sdmac->status = old_status; | |
| } | |
| } | |
| static void mxc_sdma_handle_channel_normal(unsigned long data) | |
| { | |
| struct sdma_channel *sdmac = (struct sdma_channel *) data; | |
| struct sdma_buffer_descriptor *bd; | |
| int i, error = 0; | |
| sdmac->chn_real_count = 0; | |
| /* | |
| * non loop mode. Iterate over all descriptors, collect | |
| * errors and call callback function | |
| */ | |
| for (i = 0; i < sdmac->num_bd; i++) { | |
| bd = &sdmac->bd[i]; | |
| if (bd->mode.status & (BD_DONE | BD_RROR)) | |
| error = -EIO; | |
| sdmac->chn_real_count += bd->mode.count; | |
| } | |
| if (error) | |
| sdmac->status = DMA_ERROR; | |
| else | |
| sdmac->status = DMA_COMPLETE; | |
| dma_cookie_complete(&sdmac->desc); | |
| dmaengine_desc_get_callback_invoke(&sdmac->desc, NULL); | |
| } | |
| static irqreturn_t sdma_int_handler(int irq, void *dev_id) | |
| { | |
| struct sdma_engine *sdma = dev_id; | |
| unsigned long stat; | |
| stat = readl_relaxed(sdma->regs + SDMA_H_INTR); | |
| writel_relaxed(stat, sdma->regs + SDMA_H_INTR); | |
| /* channel 0 is special and not handled here, see run_channel0() */ | |
| stat &= ~1; | |
| while (stat) { | |
| int channel = fls(stat) - 1; | |
| struct sdma_channel *sdmac = &sdma->channel[channel]; | |
| if (sdmac->flags & IMX_DMA_SG_LOOP) | |
| sdma_update_channel_loop(sdmac); | |
| else | |
| tasklet_schedule(&sdmac->tasklet); | |
| __clear_bit(channel, &stat); | |
| } | |
| return IRQ_HANDLED; | |
| } | |
| /* | |
| * sets the pc of SDMA script according to the peripheral type | |
| */ | |
| static void sdma_get_pc(struct sdma_channel *sdmac, | |
| enum sdma_peripheral_type peripheral_type) | |
| { | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| int per_2_emi = 0, emi_2_per = 0; | |
| /* | |
| * These are needed once we start to support transfers between | |
| * two peripherals or memory-to-memory transfers | |
| */ | |
| int per_2_per = 0; | |
| sdmac->pc_from_device = 0; | |
| sdmac->pc_to_device = 0; | |
| sdmac->device_to_device = 0; | |
| switch (peripheral_type) { | |
| case IMX_DMATYPE_MEMORY: | |
| break; | |
| case IMX_DMATYPE_DSP: | |
| emi_2_per = sdma->script_addrs->bp_2_ap_addr; | |
| per_2_emi = sdma->script_addrs->ap_2_bp_addr; | |
| break; | |
| case IMX_DMATYPE_FIRI: | |
| per_2_emi = sdma->script_addrs->firi_2_mcu_addr; | |
| emi_2_per = sdma->script_addrs->mcu_2_firi_addr; | |
| break; | |
| case IMX_DMATYPE_UART: | |
| per_2_emi = sdma->script_addrs->uart_2_mcu_addr; | |
| emi_2_per = sdma->script_addrs->mcu_2_app_addr; | |
| break; | |
| case IMX_DMATYPE_UART_SP: | |
| per_2_emi = sdma->script_addrs->uartsh_2_mcu_addr; | |
| emi_2_per = sdma->script_addrs->mcu_2_shp_addr; | |
| break; | |
| case IMX_DMATYPE_ATA: | |
| per_2_emi = sdma->script_addrs->ata_2_mcu_addr; | |
| emi_2_per = sdma->script_addrs->mcu_2_ata_addr; | |
| break; | |
| case IMX_DMATYPE_CSPI: | |
| case IMX_DMATYPE_EXT: | |
| case IMX_DMATYPE_SSI: | |
| case IMX_DMATYPE_SAI: | |
| per_2_emi = sdma->script_addrs->app_2_mcu_addr; | |
| emi_2_per = sdma->script_addrs->mcu_2_app_addr; | |
| break; | |
| case IMX_DMATYPE_SSI_DUAL: | |
| per_2_emi = sdma->script_addrs->ssish_2_mcu_addr; | |
| emi_2_per = sdma->script_addrs->mcu_2_ssish_addr; | |
| break; | |
| case IMX_DMATYPE_SSI_SP: | |
| case IMX_DMATYPE_MMC: | |
| case IMX_DMATYPE_SDHC: | |
| case IMX_DMATYPE_CSPI_SP: | |
| case IMX_DMATYPE_ESAI: | |
| case IMX_DMATYPE_MSHC_SP: | |
| per_2_emi = sdma->script_addrs->shp_2_mcu_addr; | |
| emi_2_per = sdma->script_addrs->mcu_2_shp_addr; | |
| break; | |
| case IMX_DMATYPE_ASRC: | |
| per_2_emi = sdma->script_addrs->asrc_2_mcu_addr; | |
| emi_2_per = sdma->script_addrs->asrc_2_mcu_addr; | |
| per_2_per = sdma->script_addrs->per_2_per_addr; | |
| break; | |
| case IMX_DMATYPE_ASRC_SP: | |
| per_2_emi = sdma->script_addrs->shp_2_mcu_addr; | |
| emi_2_per = sdma->script_addrs->mcu_2_shp_addr; | |
| per_2_per = sdma->script_addrs->per_2_per_addr; | |
| break; | |
| case IMX_DMATYPE_MSHC: | |
| per_2_emi = sdma->script_addrs->mshc_2_mcu_addr; | |
| emi_2_per = sdma->script_addrs->mcu_2_mshc_addr; | |
| break; | |
| case IMX_DMATYPE_CCM: | |
| per_2_emi = sdma->script_addrs->dptc_dvfs_addr; | |
| break; | |
| case IMX_DMATYPE_SPDIF: | |
| per_2_emi = sdma->script_addrs->spdif_2_mcu_addr; | |
| emi_2_per = sdma->script_addrs->mcu_2_spdif_addr; | |
| break; | |
| case IMX_DMATYPE_IPU_MEMORY: | |
| emi_2_per = sdma->script_addrs->ext_mem_2_ipu_addr; | |
| break; | |
| default: | |
| break; | |
| } | |
| sdmac->pc_from_device = per_2_emi; | |
| sdmac->pc_to_device = emi_2_per; | |
| sdmac->device_to_device = per_2_per; | |
| } | |
| static int sdma_load_context(struct sdma_channel *sdmac) | |
| { | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| int channel = sdmac->channel; | |
| int load_address; | |
| struct sdma_context_data *context = sdma->context; | |
| struct sdma_buffer_descriptor *bd0 = sdma->channel[0].bd; | |
| int ret; | |
| unsigned long flags; | |
| if (sdmac->direction == DMA_DEV_TO_MEM) | |
| load_address = sdmac->pc_from_device; | |
| else if (sdmac->direction == DMA_DEV_TO_DEV) | |
| load_address = sdmac->device_to_device; | |
| else | |
| load_address = sdmac->pc_to_device; | |
| if (load_address < 0) | |
| return load_address; | |
| dev_dbg(sdma->dev, "load_address = %d\n", load_address); | |
| dev_dbg(sdma->dev, "wml = 0x%08x\n", (u32)sdmac->watermark_level); | |
| dev_dbg(sdma->dev, "shp_addr = 0x%08x\n", sdmac->shp_addr); | |
| dev_dbg(sdma->dev, "per_addr = 0x%08x\n", sdmac->per_addr); | |
| dev_dbg(sdma->dev, "event_mask0 = 0x%08x\n", (u32)sdmac->event_mask[0]); | |
| dev_dbg(sdma->dev, "event_mask1 = 0x%08x\n", (u32)sdmac->event_mask[1]); | |
| spin_lock_irqsave(&sdma->channel_0_lock, flags); | |
| memset(context, 0, sizeof(*context)); | |
| context->channel_state.pc = load_address; | |
| /* Send by context the event mask,base address for peripheral | |
| * and watermark level | |
| */ | |
| context->gReg[0] = sdmac->event_mask[1]; | |
| context->gReg[1] = sdmac->event_mask[0]; | |
| context->gReg[2] = sdmac->per_addr; | |
| context->gReg[6] = sdmac->shp_addr; | |
| context->gReg[7] = sdmac->watermark_level; | |
| bd0->mode.command = C0_SETDM; | |
| bd0->mode.status = BD_DONE | BD_INTR | BD_WRAP | BD_EXTD; | |
| bd0->mode.count = sizeof(*context) / 4; | |
| bd0->buffer_addr = sdma->context_phys; | |
| bd0->ext_buffer_addr = 2048 + (sizeof(*context) / 4) * channel; | |
| ret = sdma_run_channel0(sdma); | |
| spin_unlock_irqrestore(&sdma->channel_0_lock, flags); | |
| return ret; | |
| } | |
| static struct sdma_channel *to_sdma_chan(struct dma_chan *chan) | |
| { | |
| return container_of(chan, struct sdma_channel, chan); | |
| } | |
| static int sdma_disable_channel(struct dma_chan *chan) | |
| { | |
| struct sdma_channel *sdmac = to_sdma_chan(chan); | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| int channel = sdmac->channel; | |
| writel_relaxed(BIT(channel), sdma->regs + SDMA_H_STATSTOP); | |
| sdmac->status = DMA_ERROR; | |
| return 0; | |
| } | |
| static void sdma_set_watermarklevel_for_p2p(struct sdma_channel *sdmac) | |
| { | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| int lwml = sdmac->watermark_level & SDMA_WATERMARK_LEVEL_LWML; | |
| int hwml = (sdmac->watermark_level & SDMA_WATERMARK_LEVEL_HWML) >> 16; | |
| set_bit(sdmac->event_id0 % 32, &sdmac->event_mask[1]); | |
| set_bit(sdmac->event_id1 % 32, &sdmac->event_mask[0]); | |
| if (sdmac->event_id0 > 31) | |
| sdmac->watermark_level |= SDMA_WATERMARK_LEVEL_LWE; | |
| if (sdmac->event_id1 > 31) | |
| sdmac->watermark_level |= SDMA_WATERMARK_LEVEL_HWE; | |
| /* | |
| * If LWML(src_maxburst) > HWML(dst_maxburst), we need | |
| * swap LWML and HWML of INFO(A.3.2.5.1), also need swap | |
| * r0(event_mask[1]) and r1(event_mask[0]). | |
| */ | |
| if (lwml > hwml) { | |
| sdmac->watermark_level &= ~(SDMA_WATERMARK_LEVEL_LWML | | |
| SDMA_WATERMARK_LEVEL_HWML); | |
| sdmac->watermark_level |= hwml; | |
| sdmac->watermark_level |= lwml << 16; | |
| swap(sdmac->event_mask[0], sdmac->event_mask[1]); | |
| } | |
| if (sdmac->per_address2 >= sdma->spba_start_addr && | |
| sdmac->per_address2 <= sdma->spba_end_addr) | |
| sdmac->watermark_level |= SDMA_WATERMARK_LEVEL_SP; | |
| if (sdmac->per_address >= sdma->spba_start_addr && | |
| sdmac->per_address <= sdma->spba_end_addr) | |
| sdmac->watermark_level |= SDMA_WATERMARK_LEVEL_DP; | |
| sdmac->watermark_level |= SDMA_WATERMARK_LEVEL_CONT; | |
| } | |
| static int sdma_config_channel(struct dma_chan *chan) | |
| { | |
| struct sdma_channel *sdmac = to_sdma_chan(chan); | |
| int ret; | |
| sdma_disable_channel(chan); | |
| sdmac->event_mask[0] = 0; | |
| sdmac->event_mask[1] = 0; | |
| sdmac->shp_addr = 0; | |
| sdmac->per_addr = 0; | |
| if (sdmac->event_id0) { | |
| if (sdmac->event_id0 >= sdmac->sdma->drvdata->num_events) | |
| return -EINVAL; | |
| sdma_event_enable(sdmac, sdmac->event_id0); | |
| } | |
| if (sdmac->event_id1) { | |
| if (sdmac->event_id1 >= sdmac->sdma->drvdata->num_events) | |
| return -EINVAL; | |
| sdma_event_enable(sdmac, sdmac->event_id1); | |
| } | |
| switch (sdmac->peripheral_type) { | |
| case IMX_DMATYPE_DSP: | |
| sdma_config_ownership(sdmac, false, true, true); | |
| break; | |
| case IMX_DMATYPE_MEMORY: | |
| sdma_config_ownership(sdmac, false, true, false); | |
| break; | |
| default: | |
| sdma_config_ownership(sdmac, true, true, false); | |
| break; | |
| } | |
| sdma_get_pc(sdmac, sdmac->peripheral_type); | |
| if ((sdmac->peripheral_type != IMX_DMATYPE_MEMORY) && | |
| (sdmac->peripheral_type != IMX_DMATYPE_DSP)) { | |
| /* Handle multiple event channels differently */ | |
| if (sdmac->event_id1) { | |
| if (sdmac->peripheral_type == IMX_DMATYPE_ASRC_SP || | |
| sdmac->peripheral_type == IMX_DMATYPE_ASRC) | |
| sdma_set_watermarklevel_for_p2p(sdmac); | |
| } else | |
| __set_bit(sdmac->event_id0, sdmac->event_mask); | |
| /* Address */ | |
| sdmac->shp_addr = sdmac->per_address; | |
| sdmac->per_addr = sdmac->per_address2; | |
| } else { | |
| sdmac->watermark_level = 0; /* FIXME: M3_BASE_ADDRESS */ | |
| } | |
| ret = sdma_load_context(sdmac); | |
| return ret; | |
| } | |
| static int sdma_set_channel_priority(struct sdma_channel *sdmac, | |
| unsigned int priority) | |
| { | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| int channel = sdmac->channel; | |
| if (priority < MXC_SDMA_MIN_PRIORITY | |
| || priority > MXC_SDMA_MAX_PRIORITY) { | |
| return -EINVAL; | |
| } | |
| writel_relaxed(priority, sdma->regs + SDMA_CHNPRI_0 + 4 * channel); | |
| return 0; | |
| } | |
| static int sdma_request_channel(struct sdma_channel *sdmac) | |
| { | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| int channel = sdmac->channel; | |
| int ret = -EBUSY; | |
| sdmac->bd = dma_zalloc_coherent(NULL, PAGE_SIZE, &sdmac->bd_phys, | |
| GFP_KERNEL); | |
| if (!sdmac->bd) { | |
| ret = -ENOMEM; | |
| goto out; | |
| } | |
| sdma->channel_control[channel].base_bd_ptr = sdmac->bd_phys; | |
| sdma->channel_control[channel].current_bd_ptr = sdmac->bd_phys; | |
| sdma_set_channel_priority(sdmac, MXC_SDMA_DEFAULT_PRIORITY); | |
| return 0; | |
| out: | |
| return ret; | |
| } | |
| static dma_cookie_t sdma_tx_submit(struct dma_async_tx_descriptor *tx) | |
| { | |
| unsigned long flags; | |
| struct sdma_channel *sdmac = to_sdma_chan(tx->chan); | |
| dma_cookie_t cookie; | |
| spin_lock_irqsave(&sdmac->lock, flags); | |
| cookie = dma_cookie_assign(tx); | |
| spin_unlock_irqrestore(&sdmac->lock, flags); | |
| return cookie; | |
| } | |
| static int sdma_alloc_chan_resources(struct dma_chan *chan) | |
| { | |
| struct sdma_channel *sdmac = to_sdma_chan(chan); | |
| struct imx_dma_data *data = chan->private; | |
| int prio, ret; | |
| if (!data) | |
| return -EINVAL; | |
| switch (data->priority) { | |
| case DMA_PRIO_HIGH: | |
| prio = 3; | |
| break; | |
| case DMA_PRIO_MEDIUM: | |
| prio = 2; | |
| break; | |
| case DMA_PRIO_LOW: | |
| default: | |
| prio = 1; | |
| break; | |
| } | |
| sdmac->peripheral_type = data->peripheral_type; | |
| sdmac->event_id0 = data->dma_request; | |
| sdmac->event_id1 = data->dma_request2; | |
| ret = clk_enable(sdmac->sdma->clk_ipg); | |
| if (ret) | |
| return ret; | |
| ret = clk_enable(sdmac->sdma->clk_ahb); | |
| if (ret) | |
| goto disable_clk_ipg; | |
| ret = sdma_request_channel(sdmac); | |
| if (ret) | |
| goto disable_clk_ahb; | |
| ret = sdma_set_channel_priority(sdmac, prio); | |
| if (ret) | |
| goto disable_clk_ahb; | |
| dma_async_tx_descriptor_init(&sdmac->desc, chan); | |
| sdmac->desc.tx_submit = sdma_tx_submit; | |
| /* txd.flags will be overwritten in prep funcs */ | |
| sdmac->desc.flags = DMA_CTRL_ACK; | |
| return 0; | |
| disable_clk_ahb: | |
| clk_disable(sdmac->sdma->clk_ahb); | |
| disable_clk_ipg: | |
| clk_disable(sdmac->sdma->clk_ipg); | |
| return ret; | |
| } | |
| static void sdma_free_chan_resources(struct dma_chan *chan) | |
| { | |
| struct sdma_channel *sdmac = to_sdma_chan(chan); | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| sdma_disable_channel(chan); | |
| if (sdmac->event_id0) | |
| sdma_event_disable(sdmac, sdmac->event_id0); | |
| if (sdmac->event_id1) | |
| sdma_event_disable(sdmac, sdmac->event_id1); | |
| sdmac->event_id0 = 0; | |
| sdmac->event_id1 = 0; | |
| sdma_set_channel_priority(sdmac, 0); | |
| dma_free_coherent(NULL, PAGE_SIZE, sdmac->bd, sdmac->bd_phys); | |
| clk_disable(sdma->clk_ipg); | |
| clk_disable(sdma->clk_ahb); | |
| } | |
| static struct dma_async_tx_descriptor *sdma_prep_slave_sg( | |
| struct dma_chan *chan, struct scatterlist *sgl, | |
| unsigned int sg_len, enum dma_transfer_direction direction, | |
| unsigned long flags, void *context) | |
| { | |
| struct sdma_channel *sdmac = to_sdma_chan(chan); | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| int ret, i, count; | |
| int channel = sdmac->channel; | |
| struct scatterlist *sg; | |
| if (sdmac->status == DMA_IN_PROGRESS) | |
| return NULL; | |
| sdmac->status = DMA_IN_PROGRESS; | |
| sdmac->flags = 0; | |
| sdmac->buf_tail = 0; | |
| dev_dbg(sdma->dev, "setting up %d entries for channel %d.\n", | |
| sg_len, channel); | |
| sdmac->direction = direction; | |
| ret = sdma_load_context(sdmac); | |
| if (ret) | |
| goto err_out; | |
| if (sg_len > NUM_BD) { | |
| dev_err(sdma->dev, "SDMA channel %d: maximum number of sg exceeded: %d > %d\n", | |
| channel, sg_len, NUM_BD); | |
| ret = -EINVAL; | |
| goto err_out; | |
| } | |
| sdmac->chn_count = 0; | |
| for_each_sg(sgl, sg, sg_len, i) { | |
| struct sdma_buffer_descriptor *bd = &sdmac->bd[i]; | |
| int param; | |
| bd->buffer_addr = sg->dma_address; | |
| count = sg_dma_len(sg); | |
| if (count > 0xffff) { | |
| dev_err(sdma->dev, "SDMA channel %d: maximum bytes for sg entry exceeded: %d > %d\n", | |
| channel, count, 0xffff); | |
| ret = -EINVAL; | |
| goto err_out; | |
| } | |
| bd->mode.count = count; | |
| sdmac->chn_count += count; | |
| if (sdmac->word_size > DMA_SLAVE_BUSWIDTH_4_BYTES) { | |
| ret = -EINVAL; | |
| goto err_out; | |
| } | |
| switch (sdmac->word_size) { | |
| case DMA_SLAVE_BUSWIDTH_4_BYTES: | |
| bd->mode.command = 0; | |
| if (count & 3 || sg->dma_address & 3) | |
| return NULL; | |
| break; | |
| case DMA_SLAVE_BUSWIDTH_2_BYTES: | |
| bd->mode.command = 2; | |
| if (count & 1 || sg->dma_address & 1) | |
| return NULL; | |
| break; | |
| case DMA_SLAVE_BUSWIDTH_1_BYTE: | |
| bd->mode.command = 1; | |
| break; | |
| default: | |
| return NULL; | |
| } | |
| param = BD_DONE | BD_EXTD | BD_CONT; | |
| if (i + 1 == sg_len) { | |
| param |= BD_INTR; | |
| param |= BD_LAST; | |
| param &= ~BD_CONT; | |
| } | |
| dev_dbg(sdma->dev, "entry %d: count: %d dma: %#llx %s%s\n", | |
| i, count, (u64)sg->dma_address, | |
| param & BD_WRAP ? "wrap" : "", | |
| param & BD_INTR ? " intr" : ""); | |
| bd->mode.status = param; | |
| } | |
| sdmac->num_bd = sg_len; | |
| sdma->channel_control[channel].current_bd_ptr = sdmac->bd_phys; | |
| return &sdmac->desc; | |
| err_out: | |
| sdmac->status = DMA_ERROR; | |
| return NULL; | |
| } | |
| static struct dma_async_tx_descriptor *sdma_prep_dma_cyclic( | |
| struct dma_chan *chan, dma_addr_t dma_addr, size_t buf_len, | |
| size_t period_len, enum dma_transfer_direction direction, | |
| unsigned long flags) | |
| { | |
| struct sdma_channel *sdmac = to_sdma_chan(chan); | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| int num_periods = buf_len / period_len; | |
| int channel = sdmac->channel; | |
| int ret, i = 0, buf = 0; | |
| dev_dbg(sdma->dev, "%s channel: %d\n", __func__, channel); | |
| if (sdmac->status == DMA_IN_PROGRESS) | |
| return NULL; | |
| sdmac->status = DMA_IN_PROGRESS; | |
| sdmac->buf_tail = 0; | |
| sdmac->period_len = period_len; | |
| sdmac->flags |= IMX_DMA_SG_LOOP; | |
| sdmac->direction = direction; | |
| ret = sdma_load_context(sdmac); | |
| if (ret) | |
| goto err_out; | |
| if (num_periods > NUM_BD) { | |
| dev_err(sdma->dev, "SDMA channel %d: maximum number of sg exceeded: %d > %d\n", | |
| channel, num_periods, NUM_BD); | |
| goto err_out; | |
| } | |
| if (period_len > 0xffff) { | |
| dev_err(sdma->dev, "SDMA channel %d: maximum period size exceeded: %d > %d\n", | |
| channel, period_len, 0xffff); | |
| goto err_out; | |
| } | |
| while (buf < buf_len) { | |
| struct sdma_buffer_descriptor *bd = &sdmac->bd[i]; | |
| int param; | |
| bd->buffer_addr = dma_addr; | |
| bd->mode.count = period_len; | |
| if (sdmac->word_size > DMA_SLAVE_BUSWIDTH_4_BYTES) | |
| goto err_out; | |
| if (sdmac->word_size == DMA_SLAVE_BUSWIDTH_4_BYTES) | |
| bd->mode.command = 0; | |
| else | |
| bd->mode.command = sdmac->word_size; | |
| param = BD_DONE | BD_EXTD | BD_CONT | BD_INTR; | |
| if (i + 1 == num_periods) | |
| param |= BD_WRAP; | |
| dev_dbg(sdma->dev, "entry %d: count: %d dma: %#llx %s%s\n", | |
| i, period_len, (u64)dma_addr, | |
| param & BD_WRAP ? "wrap" : "", | |
| param & BD_INTR ? " intr" : ""); | |
| bd->mode.status = param; | |
| dma_addr += period_len; | |
| buf += period_len; | |
| i++; | |
| } | |
| sdmac->num_bd = num_periods; | |
| sdma->channel_control[channel].current_bd_ptr = sdmac->bd_phys; | |
| return &sdmac->desc; | |
| err_out: | |
| sdmac->status = DMA_ERROR; | |
| return NULL; | |
| } | |
| static int sdma_config(struct dma_chan *chan, | |
| struct dma_slave_config *dmaengine_cfg) | |
| { | |
| struct sdma_channel *sdmac = to_sdma_chan(chan); | |
| if (dmaengine_cfg->direction == DMA_DEV_TO_MEM) { | |
| sdmac->per_address = dmaengine_cfg->src_addr; | |
| sdmac->watermark_level = dmaengine_cfg->src_maxburst * | |
| dmaengine_cfg->src_addr_width; | |
| sdmac->word_size = dmaengine_cfg->src_addr_width; | |
| } else if (dmaengine_cfg->direction == DMA_DEV_TO_DEV) { | |
| sdmac->per_address2 = dmaengine_cfg->src_addr; | |
| sdmac->per_address = dmaengine_cfg->dst_addr; | |
| sdmac->watermark_level = dmaengine_cfg->src_maxburst & | |
| SDMA_WATERMARK_LEVEL_LWML; | |
| sdmac->watermark_level |= (dmaengine_cfg->dst_maxburst << 16) & | |
| SDMA_WATERMARK_LEVEL_HWML; | |
| sdmac->word_size = dmaengine_cfg->dst_addr_width; | |
| } else { | |
| sdmac->per_address = dmaengine_cfg->dst_addr; | |
| sdmac->watermark_level = dmaengine_cfg->dst_maxburst * | |
| dmaengine_cfg->dst_addr_width; | |
| sdmac->word_size = dmaengine_cfg->dst_addr_width; | |
| } | |
| sdmac->direction = dmaengine_cfg->direction; | |
| return sdma_config_channel(chan); | |
| } | |
| static enum dma_status sdma_tx_status(struct dma_chan *chan, | |
| dma_cookie_t cookie, | |
| struct dma_tx_state *txstate) | |
| { | |
| struct sdma_channel *sdmac = to_sdma_chan(chan); | |
| u32 residue; | |
| if (sdmac->flags & IMX_DMA_SG_LOOP) | |
| residue = (sdmac->num_bd - sdmac->buf_tail) * | |
| sdmac->period_len - sdmac->chn_real_count; | |
| else | |
| residue = sdmac->chn_count - sdmac->chn_real_count; | |
| dma_set_tx_state(txstate, chan->completed_cookie, chan->cookie, | |
| residue); | |
| return sdmac->status; | |
| } | |
| static void sdma_issue_pending(struct dma_chan *chan) | |
| { | |
| struct sdma_channel *sdmac = to_sdma_chan(chan); | |
| struct sdma_engine *sdma = sdmac->sdma; | |
| if (sdmac->status == DMA_IN_PROGRESS) | |
| sdma_enable_channel(sdma, sdmac->channel); | |
| } | |
| #define SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V1 34 | |
| #define SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V2 38 | |
| #define SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3 41 | |
| #define SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V4 42 | |
| static void sdma_add_scripts(struct sdma_engine *sdma, | |
| const struct sdma_script_start_addrs *addr) | |
| { | |
| s32 *addr_arr = (u32 *)addr; | |
| s32 *saddr_arr = (u32 *)sdma->script_addrs; | |
| int i; | |
| /* use the default firmware in ROM if missing external firmware */ | |
| if (!sdma->script_number) | |
| sdma->script_number = SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V1; | |
| for (i = 0; i < sdma->script_number; i++) | |
| if (addr_arr[i] > 0) | |
| saddr_arr[i] = addr_arr[i]; | |
| } | |
| static void sdma_load_firmware(const struct firmware *fw, void *context) | |
| { | |
| struct sdma_engine *sdma = context; | |
| const struct sdma_firmware_header *header; | |
| const struct sdma_script_start_addrs *addr; | |
| unsigned short *ram_code; | |
| if (!fw) { | |
| dev_info(sdma->dev, "external firmware not found, using ROM firmware\n"); | |
| /* In this case we just use the ROM firmware. */ | |
| return; | |
| } | |
| if (fw->size < sizeof(*header)) | |
| goto err_firmware; | |
| header = (struct sdma_firmware_header *)fw->data; | |
| if (header->magic != SDMA_FIRMWARE_MAGIC) | |
| goto err_firmware; | |
| if (header->ram_code_start + header->ram_code_size > fw->size) | |
| goto err_firmware; | |
| switch (header->version_major) { | |
| case 1: | |
| sdma->script_number = SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V1; | |
| break; | |
| case 2: | |
| sdma->script_number = SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V2; | |
| break; | |
| case 3: | |
| sdma->script_number = SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3; | |
| break; | |
| case 4: | |
| sdma->script_number = SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V4; | |
| break; | |
| default: | |
| dev_err(sdma->dev, "unknown firmware version\n"); | |
| goto err_firmware; | |
| } | |
| addr = (void *)header + header->script_addrs_start; | |
| ram_code = (void *)header + header->ram_code_start; | |
| clk_enable(sdma->clk_ipg); | |
| clk_enable(sdma->clk_ahb); | |
| /* download the RAM image for SDMA */ | |
| sdma_load_script(sdma, ram_code, | |
| header->ram_code_size, | |
| addr->ram_code_start_addr); | |
| clk_disable(sdma->clk_ipg); | |
| clk_disable(sdma->clk_ahb); | |
| sdma_add_scripts(sdma, addr); | |
| dev_info(sdma->dev, "loaded firmware %d.%d\n", | |
| header->version_major, | |
| header->version_minor); | |
| err_firmware: | |
| release_firmware(fw); | |
| } | |
| #define EVENT_REMAP_CELLS 3 | |
| static int sdma_event_remap(struct sdma_engine *sdma) | |
| { | |
| struct device_node *np = sdma->dev->of_node; | |
| struct device_node *gpr_np = of_parse_phandle(np, "gpr", 0); | |
| struct property *event_remap; | |
| struct regmap *gpr; | |
| char propname[] = "fsl,sdma-event-remap"; | |
| u32 reg, val, shift, num_map, i; | |
| int ret = 0; | |
| if (IS_ERR(np) || IS_ERR(gpr_np)) | |
| goto out; | |
| event_remap = of_find_property(np, propname, NULL); | |
| num_map = event_remap ? (event_remap->length / sizeof(u32)) : 0; | |
| if (!num_map) { | |
| dev_dbg(sdma->dev, "no event needs to be remapped\n"); | |
| goto out; | |
| } else if (num_map % EVENT_REMAP_CELLS) { | |
| dev_err(sdma->dev, "the property %s must modulo %d\n", | |
| propname, EVENT_REMAP_CELLS); | |
| ret = -EINVAL; | |
| goto out; | |
| } | |
| gpr = syscon_node_to_regmap(gpr_np); | |
| if (IS_ERR(gpr)) { | |
| dev_err(sdma->dev, "failed to get gpr regmap\n"); | |
| ret = PTR_ERR(gpr); | |
| goto out; | |
| } | |
| for (i = 0; i < num_map; i += EVENT_REMAP_CELLS) { | |
| ret = of_property_read_u32_index(np, propname, i, ®); | |
| if (ret) { | |
| dev_err(sdma->dev, "failed to read property %s index %d\n", | |
| propname, i); | |
| goto out; | |
| } | |
| ret = of_property_read_u32_index(np, propname, i + 1, &shift); | |
| if (ret) { | |
| dev_err(sdma->dev, "failed to read property %s index %d\n", | |
| propname, i + 1); | |
| goto out; | |
| } | |
| ret = of_property_read_u32_index(np, propname, i + 2, &val); | |
| if (ret) { | |
| dev_err(sdma->dev, "failed to read property %s index %d\n", | |
| propname, i + 2); | |
| goto out; | |
| } | |
| regmap_update_bits(gpr, reg, BIT(shift), val << shift); | |
| } | |
| out: | |
| if (!IS_ERR(gpr_np)) | |
| of_node_put(gpr_np); | |
| return ret; | |
| } | |
| static int sdma_get_firmware(struct sdma_engine *sdma, | |
| const char *fw_name) | |
| { | |
| int ret; | |
| ret = request_firmware_nowait(THIS_MODULE, | |
| FW_ACTION_HOTPLUG, fw_name, sdma->dev, | |
| GFP_KERNEL, sdma, sdma_load_firmware); | |
| return ret; | |
| } | |
| static int sdma_init(struct sdma_engine *sdma) | |
| { | |
| int i, ret; | |
| dma_addr_t ccb_phys; | |
| ret = clk_enable(sdma->clk_ipg); | |
| if (ret) | |
| return ret; | |
| ret = clk_enable(sdma->clk_ahb); | |
| if (ret) | |
| goto disable_clk_ipg; | |
| /* Be sure SDMA has not started yet */ | |
| writel_relaxed(0, sdma->regs + SDMA_H_C0PTR); | |
| sdma->channel_control = dma_alloc_coherent(NULL, | |
| MAX_DMA_CHANNELS * sizeof (struct sdma_channel_control) + | |
| sizeof(struct sdma_context_data), | |
| &ccb_phys, GFP_KERNEL); | |
| if (!sdma->channel_control) { | |
| ret = -ENOMEM; | |
| goto err_dma_alloc; | |
| } | |
| sdma->context = (void *)sdma->channel_control + | |
| MAX_DMA_CHANNELS * sizeof (struct sdma_channel_control); | |
| sdma->context_phys = ccb_phys + | |
| MAX_DMA_CHANNELS * sizeof (struct sdma_channel_control); | |
| /* Zero-out the CCB structures array just allocated */ | |
| memset(sdma->channel_control, 0, | |
| MAX_DMA_CHANNELS * sizeof (struct sdma_channel_control)); | |
| /* disable all channels */ | |
| for (i = 0; i < sdma->drvdata->num_events; i++) | |
| writel_relaxed(0, sdma->regs + chnenbl_ofs(sdma, i)); | |
| /* All channels have priority 0 */ | |
| for (i = 0; i < MAX_DMA_CHANNELS; i++) | |
| writel_relaxed(0, sdma->regs + SDMA_CHNPRI_0 + i * 4); | |
| ret = sdma_request_channel(&sdma->channel[0]); | |
| if (ret) | |
| goto err_dma_alloc; | |
| sdma_config_ownership(&sdma->channel[0], false, true, false); | |
| /* Set Command Channel (Channel Zero) */ | |
| writel_relaxed(0x4050, sdma->regs + SDMA_CHN0ADDR); | |
| /* Set bits of CONFIG register but with static context switching */ | |
| /* FIXME: Check whether to set ACR bit depending on clock ratios */ | |
| writel_relaxed(0, sdma->regs + SDMA_H_CONFIG); | |
| writel_relaxed(ccb_phys, sdma->regs + SDMA_H_C0PTR); | |
| /* Initializes channel's priorities */ | |
| sdma_set_channel_priority(&sdma->channel[0], 7); | |
| clk_disable(sdma->clk_ipg); | |
| clk_disable(sdma->clk_ahb); | |
| return 0; | |
| err_dma_alloc: | |
| clk_disable(sdma->clk_ahb); | |
| disable_clk_ipg: | |
| clk_disable(sdma->clk_ipg); | |
| dev_err(sdma->dev, "initialisation failed with %d\n", ret); | |
| return ret; | |
| } | |
| static bool sdma_filter_fn(struct dma_chan *chan, void *fn_param) | |
| { | |
| struct sdma_channel *sdmac = to_sdma_chan(chan); | |
| struct imx_dma_data *data = fn_param; | |
| if (!imx_dma_is_general_purpose(chan)) | |
| return false; | |
| sdmac->data = *data; | |
| chan->private = &sdmac->data; | |
| return true; | |
| } | |
| static struct dma_chan *sdma_xlate(struct of_phandle_args *dma_spec, | |
| struct of_dma *ofdma) | |
| { | |
| struct sdma_engine *sdma = ofdma->of_dma_data; | |
| dma_cap_mask_t mask = sdma->dma_device.cap_mask; | |
| struct imx_dma_data data; | |
| if (dma_spec->args_count != 3) | |
| return NULL; | |
| data.dma_request = dma_spec->args[0]; | |
| data.peripheral_type = dma_spec->args[1]; | |
| data.priority = dma_spec->args[2]; | |
| /* | |
| * init dma_request2 to zero, which is not used by the dts. | |
| * For P2P, dma_request2 is init from dma_request_channel(), | |
| * chan->private will point to the imx_dma_data, and in | |
| * device_alloc_chan_resources(), imx_dma_data.dma_request2 will | |
| * be set to sdmac->event_id1. | |
| */ | |
| data.dma_request2 = 0; | |
| return dma_request_channel(mask, sdma_filter_fn, &data); | |
| } | |
| static int sdma_probe(struct platform_device *pdev) | |
| { | |
| const struct of_device_id *of_id = | |
| of_match_device(sdma_dt_ids, &pdev->dev); | |
| struct device_node *np = pdev->dev.of_node; | |
| struct device_node *spba_bus; | |
| const char *fw_name; | |
| int ret; | |
| int irq; | |
| struct resource *iores; | |
| struct resource spba_res; | |
| struct sdma_platform_data *pdata = dev_get_platdata(&pdev->dev); | |
| int i; | |
| struct sdma_engine *sdma; | |
| s32 *saddr_arr; | |
| const struct sdma_driver_data *drvdata = NULL; | |
| if (of_id) | |
| drvdata = of_id->data; | |
| else if (pdev->id_entry) | |
| drvdata = (void *)pdev->id_entry->driver_data; | |
| if (!drvdata) { | |
| dev_err(&pdev->dev, "unable to find driver data\n"); | |
| return -EINVAL; | |
| } | |
| ret = dma_coerce_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); | |
| if (ret) | |
| return ret; | |
| sdma = devm_kzalloc(&pdev->dev, sizeof(*sdma), GFP_KERNEL); | |
| if (!sdma) | |
| return -ENOMEM; | |
| spin_lock_init(&sdma->channel_0_lock); | |
| sdma->dev = &pdev->dev; | |
| sdma->drvdata = drvdata; | |
| irq = platform_get_irq(pdev, 0); | |
| if (irq < 0) | |
| return irq; | |
| iores = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
| sdma->regs = devm_ioremap_resource(&pdev->dev, iores); | |
| if (IS_ERR(sdma->regs)) | |
| return PTR_ERR(sdma->regs); | |
| sdma->clk_ipg = devm_clk_get(&pdev->dev, "ipg"); | |
| if (IS_ERR(sdma->clk_ipg)) | |
| return PTR_ERR(sdma->clk_ipg); | |
| sdma->clk_ahb = devm_clk_get(&pdev->dev, "ahb"); | |
| if (IS_ERR(sdma->clk_ahb)) | |
| return PTR_ERR(sdma->clk_ahb); | |
| clk_prepare(sdma->clk_ipg); | |
| clk_prepare(sdma->clk_ahb); | |
| ret = devm_request_irq(&pdev->dev, irq, sdma_int_handler, 0, "sdma", | |
| sdma); | |
| if (ret) | |
| return ret; | |
| sdma->irq = irq; | |
| sdma->script_addrs = kzalloc(sizeof(*sdma->script_addrs), GFP_KERNEL); | |
| if (!sdma->script_addrs) | |
| return -ENOMEM; | |
| /* initially no scripts available */ | |
| saddr_arr = (s32 *)sdma->script_addrs; | |
| for (i = 0; i < SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V1; i++) | |
| saddr_arr[i] = -EINVAL; | |
| dma_cap_set(DMA_SLAVE, sdma->dma_device.cap_mask); | |
| dma_cap_set(DMA_CYCLIC, sdma->dma_device.cap_mask); | |
| INIT_LIST_HEAD(&sdma->dma_device.channels); | |
| /* Initialize channel parameters */ | |
| for (i = 0; i < MAX_DMA_CHANNELS; i++) { | |
| struct sdma_channel *sdmac = &sdma->channel[i]; | |
| sdmac->sdma = sdma; | |
| spin_lock_init(&sdmac->lock); | |
| sdmac->chan.device = &sdma->dma_device; | |
| dma_cookie_init(&sdmac->chan); | |
| sdmac->channel = i; | |
| tasklet_init(&sdmac->tasklet, mxc_sdma_handle_channel_normal, | |
| (unsigned long) sdmac); | |
| /* | |
| * Add the channel to the DMAC list. Do not add channel 0 though | |
| * because we need it internally in the SDMA driver. This also means | |
| * that channel 0 in dmaengine counting matches sdma channel 1. | |
| */ | |
| if (i) | |
| list_add_tail(&sdmac->chan.device_node, | |
| &sdma->dma_device.channels); | |
| } | |
| ret = sdma_init(sdma); | |
| if (ret) | |
| goto err_init; | |
| ret = sdma_event_remap(sdma); | |
| if (ret) | |
| goto err_init; | |
| if (sdma->drvdata->script_addrs) | |
| sdma_add_scripts(sdma, sdma->drvdata->script_addrs); | |
| if (pdata && pdata->script_addrs) | |
| sdma_add_scripts(sdma, pdata->script_addrs); | |
| if (pdata) { | |
| ret = sdma_get_firmware(sdma, pdata->fw_name); | |
| if (ret) | |
| dev_warn(&pdev->dev, "failed to get firmware from platform data\n"); | |
| } else { | |
| /* | |
| * Because that device tree does not encode ROM script address, | |
| * the RAM script in firmware is mandatory for device tree | |
| * probe, otherwise it fails. | |
| */ | |
| ret = of_property_read_string(np, "fsl,sdma-ram-script-name", | |
| &fw_name); | |
| if (ret) | |
| dev_warn(&pdev->dev, "failed to get firmware name\n"); | |
| else { | |
| ret = sdma_get_firmware(sdma, fw_name); | |
| if (ret) | |
| dev_warn(&pdev->dev, "failed to get firmware from device tree\n"); | |
| } | |
| } | |
| sdma->dma_device.dev = &pdev->dev; | |
| sdma->dma_device.device_alloc_chan_resources = sdma_alloc_chan_resources; | |
| sdma->dma_device.device_free_chan_resources = sdma_free_chan_resources; | |
| sdma->dma_device.device_tx_status = sdma_tx_status; | |
| sdma->dma_device.device_prep_slave_sg = sdma_prep_slave_sg; | |
| sdma->dma_device.device_prep_dma_cyclic = sdma_prep_dma_cyclic; | |
| sdma->dma_device.device_config = sdma_config; | |
| sdma->dma_device.device_terminate_all = sdma_disable_channel; | |
| sdma->dma_device.src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES); | |
| sdma->dma_device.dst_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_4_BYTES); | |
| sdma->dma_device.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV); | |
| sdma->dma_device.residue_granularity = DMA_RESIDUE_GRANULARITY_BURST; | |
| sdma->dma_device.device_issue_pending = sdma_issue_pending; | |
| sdma->dma_device.dev->dma_parms = &sdma->dma_parms; | |
| dma_set_max_seg_size(sdma->dma_device.dev, 65535); | |
| platform_set_drvdata(pdev, sdma); | |
| ret = dma_async_device_register(&sdma->dma_device); | |
| if (ret) { | |
| dev_err(&pdev->dev, "unable to register\n"); | |
| goto err_init; | |
| } | |
| if (np) { | |
| ret = of_dma_controller_register(np, sdma_xlate, sdma); | |
| if (ret) { | |
| dev_err(&pdev->dev, "failed to register controller\n"); | |
| goto err_register; | |
| } | |
| spba_bus = of_find_compatible_node(NULL, NULL, "fsl,spba-bus"); | |
| ret = of_address_to_resource(spba_bus, 0, &spba_res); | |
| if (!ret) { | |
| sdma->spba_start_addr = spba_res.start; | |
| sdma->spba_end_addr = spba_res.end; | |
| } | |
| of_node_put(spba_bus); | |
| } | |
| return 0; | |
| err_register: | |
| dma_async_device_unregister(&sdma->dma_device); | |
| err_init: | |
| kfree(sdma->script_addrs); | |
| return ret; | |
| } | |
| static int sdma_remove(struct platform_device *pdev) | |
| { | |
| struct sdma_engine *sdma = platform_get_drvdata(pdev); | |
| int i; | |
| devm_free_irq(&pdev->dev, sdma->irq, sdma); | |
| dma_async_device_unregister(&sdma->dma_device); | |
| kfree(sdma->script_addrs); | |
| /* Kill the tasklet */ | |
| for (i = 0; i < MAX_DMA_CHANNELS; i++) { | |
| struct sdma_channel *sdmac = &sdma->channel[i]; | |
| tasklet_kill(&sdmac->tasklet); | |
| } | |
| platform_set_drvdata(pdev, NULL); | |
| return 0; | |
| } | |
| static struct platform_driver sdma_driver = { | |
| .driver = { | |
| .name = "imx-sdma", | |
| .of_match_table = sdma_dt_ids, | |
| }, | |
| .id_table = sdma_devtypes, | |
| .remove = sdma_remove, | |
| .probe = sdma_probe, | |
| }; | |
| module_platform_driver(sdma_driver); | |
| MODULE_AUTHOR("Sascha Hauer, Pengutronix <s.hauer@pengutronix.de>"); | |
| MODULE_DESCRIPTION("i.MX SDMA driver"); | |
| MODULE_LICENSE("GPL"); |