| /* | |
| * AMD64 class Memory Controller kernel module | |
| * | |
| * Copyright (c) 2009 SoftwareBitMaker. | |
| * Copyright (c) 2009-15 Advanced Micro Devices, Inc. | |
| * | |
| * This file may be distributed under the terms of the | |
| * GNU General Public License. | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/ctype.h> | |
| #include <linux/init.h> | |
| #include <linux/pci.h> | |
| #include <linux/pci_ids.h> | |
| #include <linux/slab.h> | |
| #include <linux/mmzone.h> | |
| #include <linux/edac.h> | |
| #include <asm/msr.h> | |
| #include "edac_core.h" | |
| #include "mce_amd.h" | |
| #define amd64_debug(fmt, arg...) \ | |
| edac_printk(KERN_DEBUG, "amd64", fmt, ##arg) | |
| #define amd64_info(fmt, arg...) \ | |
| edac_printk(KERN_INFO, "amd64", fmt, ##arg) | |
| #define amd64_notice(fmt, arg...) \ | |
| edac_printk(KERN_NOTICE, "amd64", fmt, ##arg) | |
| #define amd64_warn(fmt, arg...) \ | |
| edac_printk(KERN_WARNING, "amd64", fmt, ##arg) | |
| #define amd64_err(fmt, arg...) \ | |
| edac_printk(KERN_ERR, "amd64", fmt, ##arg) | |
| #define amd64_mc_warn(mci, fmt, arg...) \ | |
| edac_mc_chipset_printk(mci, KERN_WARNING, "amd64", fmt, ##arg) | |
| #define amd64_mc_err(mci, fmt, arg...) \ | |
| edac_mc_chipset_printk(mci, KERN_ERR, "amd64", fmt, ##arg) | |
| /* | |
| * Throughout the comments in this code, the following terms are used: | |
| * | |
| * SysAddr, DramAddr, and InputAddr | |
| * | |
| * These terms come directly from the amd64 documentation | |
| * (AMD publication #26094). They are defined as follows: | |
| * | |
| * SysAddr: | |
| * This is a physical address generated by a CPU core or a device | |
| * doing DMA. If generated by a CPU core, a SysAddr is the result of | |
| * a virtual to physical address translation by the CPU core's address | |
| * translation mechanism (MMU). | |
| * | |
| * DramAddr: | |
| * A DramAddr is derived from a SysAddr by subtracting an offset that | |
| * depends on which node the SysAddr maps to and whether the SysAddr | |
| * is within a range affected by memory hoisting. The DRAM Base | |
| * (section 3.4.4.1) and DRAM Limit (section 3.4.4.2) registers | |
| * determine which node a SysAddr maps to. | |
| * | |
| * If the DRAM Hole Address Register (DHAR) is enabled and the SysAddr | |
| * is within the range of addresses specified by this register, then | |
| * a value x from the DHAR is subtracted from the SysAddr to produce a | |
| * DramAddr. Here, x represents the base address for the node that | |
| * the SysAddr maps to plus an offset due to memory hoisting. See | |
| * section 3.4.8 and the comments in amd64_get_dram_hole_info() and | |
| * sys_addr_to_dram_addr() below for more information. | |
| * | |
| * If the SysAddr is not affected by the DHAR then a value y is | |
| * subtracted from the SysAddr to produce a DramAddr. Here, y is the | |
| * base address for the node that the SysAddr maps to. See section | |
| * 3.4.4 and the comments in sys_addr_to_dram_addr() below for more | |
| * information. | |
| * | |
| * InputAddr: | |
| * A DramAddr is translated to an InputAddr before being passed to the | |
| * memory controller for the node that the DramAddr is associated | |
| * with. The memory controller then maps the InputAddr to a csrow. | |
| * If node interleaving is not in use, then the InputAddr has the same | |
| * value as the DramAddr. Otherwise, the InputAddr is produced by | |
| * discarding the bits used for node interleaving from the DramAddr. | |
| * See section 3.4.4 for more information. | |
| * | |
| * The memory controller for a given node uses its DRAM CS Base and | |
| * DRAM CS Mask registers to map an InputAddr to a csrow. See | |
| * sections 3.5.4 and 3.5.5 for more information. | |
| */ | |
| #define EDAC_AMD64_VERSION "3.4.0" | |
| #define EDAC_MOD_STR "amd64_edac" | |
| /* Extended Model from CPUID, for CPU Revision numbers */ | |
| #define K8_REV_D 1 | |
| #define K8_REV_E 2 | |
| #define K8_REV_F 4 | |
| /* Hardware limit on ChipSelect rows per MC and processors per system */ | |
| #define NUM_CHIPSELECTS 8 | |
| #define DRAM_RANGES 8 | |
| #define ON true | |
| #define OFF false | |
| /* | |
| * PCI-defined configuration space registers | |
| */ | |
| #define PCI_DEVICE_ID_AMD_15H_NB_F1 0x1601 | |
| #define PCI_DEVICE_ID_AMD_15H_NB_F2 0x1602 | |
| #define PCI_DEVICE_ID_AMD_15H_M30H_NB_F1 0x141b | |
| #define PCI_DEVICE_ID_AMD_15H_M30H_NB_F2 0x141c | |
| #define PCI_DEVICE_ID_AMD_15H_M60H_NB_F1 0x1571 | |
| #define PCI_DEVICE_ID_AMD_15H_M60H_NB_F2 0x1572 | |
| #define PCI_DEVICE_ID_AMD_16H_NB_F1 0x1531 | |
| #define PCI_DEVICE_ID_AMD_16H_NB_F2 0x1532 | |
| #define PCI_DEVICE_ID_AMD_16H_M30H_NB_F1 0x1581 | |
| #define PCI_DEVICE_ID_AMD_16H_M30H_NB_F2 0x1582 | |
| /* | |
| * Function 1 - Address Map | |
| */ | |
| #define DRAM_BASE_LO 0x40 | |
| #define DRAM_LIMIT_LO 0x44 | |
| /* | |
| * F15 M30h D18F1x2[1C:00] | |
| */ | |
| #define DRAM_CONT_BASE 0x200 | |
| #define DRAM_CONT_LIMIT 0x204 | |
| /* | |
| * F15 M30h D18F1x2[4C:40] | |
| */ | |
| #define DRAM_CONT_HIGH_OFF 0x240 | |
| #define dram_rw(pvt, i) ((u8)(pvt->ranges[i].base.lo & 0x3)) | |
| #define dram_intlv_sel(pvt, i) ((u8)((pvt->ranges[i].lim.lo >> 8) & 0x7)) | |
| #define dram_dst_node(pvt, i) ((u8)(pvt->ranges[i].lim.lo & 0x7)) | |
| #define DHAR 0xf0 | |
| #define dhar_mem_hoist_valid(pvt) ((pvt)->dhar & BIT(1)) | |
| #define dhar_base(pvt) ((pvt)->dhar & 0xff000000) | |
| #define k8_dhar_offset(pvt) (((pvt)->dhar & 0x0000ff00) << 16) | |
| /* NOTE: Extra mask bit vs K8 */ | |
| #define f10_dhar_offset(pvt) (((pvt)->dhar & 0x0000ff80) << 16) | |
| #define DCT_CFG_SEL 0x10C | |
| #define DRAM_LOCAL_NODE_BASE 0x120 | |
| #define DRAM_LOCAL_NODE_LIM 0x124 | |
| #define DRAM_BASE_HI 0x140 | |
| #define DRAM_LIMIT_HI 0x144 | |
| /* | |
| * Function 2 - DRAM controller | |
| */ | |
| #define DCSB0 0x40 | |
| #define DCSB1 0x140 | |
| #define DCSB_CS_ENABLE BIT(0) | |
| #define DCSM0 0x60 | |
| #define DCSM1 0x160 | |
| #define csrow_enabled(i, dct, pvt) ((pvt)->csels[(dct)].csbases[(i)] & DCSB_CS_ENABLE) | |
| #define DRAM_CONTROL 0x78 | |
| #define DBAM0 0x80 | |
| #define DBAM1 0x180 | |
| /* Extract the DIMM 'type' on the i'th DIMM from the DBAM reg value passed */ | |
| #define DBAM_DIMM(i, reg) ((((reg) >> (4*(i)))) & 0xF) | |
| #define DBAM_MAX_VALUE 11 | |
| #define DCLR0 0x90 | |
| #define DCLR1 0x190 | |
| #define REVE_WIDTH_128 BIT(16) | |
| #define WIDTH_128 BIT(11) | |
| #define DCHR0 0x94 | |
| #define DCHR1 0x194 | |
| #define DDR3_MODE BIT(8) | |
| #define DCT_SEL_LO 0x110 | |
| #define dct_high_range_enabled(pvt) ((pvt)->dct_sel_lo & BIT(0)) | |
| #define dct_interleave_enabled(pvt) ((pvt)->dct_sel_lo & BIT(2)) | |
| #define dct_ganging_enabled(pvt) ((boot_cpu_data.x86 == 0x10) && ((pvt)->dct_sel_lo & BIT(4))) | |
| #define dct_data_intlv_enabled(pvt) ((pvt)->dct_sel_lo & BIT(5)) | |
| #define dct_memory_cleared(pvt) ((pvt)->dct_sel_lo & BIT(10)) | |
| #define SWAP_INTLV_REG 0x10c | |
| #define DCT_SEL_HI 0x114 | |
| #define F15H_M60H_SCRCTRL 0x1C8 | |
| /* | |
| * Function 3 - Misc Control | |
| */ | |
| #define NBCTL 0x40 | |
| #define NBCFG 0x44 | |
| #define NBCFG_CHIPKILL BIT(23) | |
| #define NBCFG_ECC_ENABLE BIT(22) | |
| /* F3x48: NBSL */ | |
| #define F10_NBSL_EXT_ERR_ECC 0x8 | |
| #define NBSL_PP_OBS 0x2 | |
| #define SCRCTRL 0x58 | |
| #define F10_ONLINE_SPARE 0xB0 | |
| #define online_spare_swap_done(pvt, c) (((pvt)->online_spare >> (1 + 2 * (c))) & 0x1) | |
| #define online_spare_bad_dramcs(pvt, c) (((pvt)->online_spare >> (4 + 4 * (c))) & 0x7) | |
| #define F10_NB_ARRAY_ADDR 0xB8 | |
| #define F10_NB_ARRAY_DRAM BIT(31) | |
| /* Bits [2:1] are used to select 16-byte section within a 64-byte cacheline */ | |
| #define SET_NB_ARRAY_ADDR(section) (((section) & 0x3) << 1) | |
| #define F10_NB_ARRAY_DATA 0xBC | |
| #define F10_NB_ARR_ECC_WR_REQ BIT(17) | |
| #define SET_NB_DRAM_INJECTION_WRITE(inj) \ | |
| (BIT(((inj.word) & 0xF) + 20) | \ | |
| F10_NB_ARR_ECC_WR_REQ | inj.bit_map) | |
| #define SET_NB_DRAM_INJECTION_READ(inj) \ | |
| (BIT(((inj.word) & 0xF) + 20) | \ | |
| BIT(16) | inj.bit_map) | |
| #define NBCAP 0xE8 | |
| #define NBCAP_CHIPKILL BIT(4) | |
| #define NBCAP_SECDED BIT(3) | |
| #define NBCAP_DCT_DUAL BIT(0) | |
| #define EXT_NB_MCA_CFG 0x180 | |
| /* MSRs */ | |
| #define MSR_MCGCTL_NBE BIT(4) | |
| enum amd_families { | |
| K8_CPUS = 0, | |
| F10_CPUS, | |
| F15_CPUS, | |
| F15_M30H_CPUS, | |
| F15_M60H_CPUS, | |
| F16_CPUS, | |
| F16_M30H_CPUS, | |
| NUM_FAMILIES, | |
| }; | |
| /* Error injection control structure */ | |
| struct error_injection { | |
| u32 section; | |
| u32 word; | |
| u32 bit_map; | |
| }; | |
| /* low and high part of PCI config space regs */ | |
| struct reg_pair { | |
| u32 lo, hi; | |
| }; | |
| /* | |
| * See F1x[1, 0][7C:40] DRAM Base/Limit Registers | |
| */ | |
| struct dram_range { | |
| struct reg_pair base; | |
| struct reg_pair lim; | |
| }; | |
| /* A DCT chip selects collection */ | |
| struct chip_select { | |
| u32 csbases[NUM_CHIPSELECTS]; | |
| u8 b_cnt; | |
| u32 csmasks[NUM_CHIPSELECTS]; | |
| u8 m_cnt; | |
| }; | |
| struct amd64_pvt { | |
| struct low_ops *ops; | |
| /* pci_device handles which we utilize */ | |
| struct pci_dev *F1, *F2, *F3; | |
| u16 mc_node_id; /* MC index of this MC node */ | |
| u8 fam; /* CPU family */ | |
| u8 model; /* ... model */ | |
| u8 stepping; /* ... stepping */ | |
| int ext_model; /* extended model value of this node */ | |
| int channel_count; | |
| /* Raw registers */ | |
| u32 dclr0; /* DRAM Configuration Low DCT0 reg */ | |
| u32 dclr1; /* DRAM Configuration Low DCT1 reg */ | |
| u32 dchr0; /* DRAM Configuration High DCT0 reg */ | |
| u32 dchr1; /* DRAM Configuration High DCT1 reg */ | |
| u32 nbcap; /* North Bridge Capabilities */ | |
| u32 nbcfg; /* F10 North Bridge Configuration */ | |
| u32 ext_nbcfg; /* Extended F10 North Bridge Configuration */ | |
| u32 dhar; /* DRAM Hoist reg */ | |
| u32 dbam0; /* DRAM Base Address Mapping reg for DCT0 */ | |
| u32 dbam1; /* DRAM Base Address Mapping reg for DCT1 */ | |
| /* one for each DCT */ | |
| struct chip_select csels[2]; | |
| /* DRAM base and limit pairs F1x[78,70,68,60,58,50,48,40] */ | |
| struct dram_range ranges[DRAM_RANGES]; | |
| u64 top_mem; /* top of memory below 4GB */ | |
| u64 top_mem2; /* top of memory above 4GB */ | |
| u32 dct_sel_lo; /* DRAM Controller Select Low */ | |
| u32 dct_sel_hi; /* DRAM Controller Select High */ | |
| u32 online_spare; /* On-Line spare Reg */ | |
| /* x4 or x8 syndromes in use */ | |
| u8 ecc_sym_sz; | |
| /* place to store error injection parameters prior to issue */ | |
| struct error_injection injection; | |
| /* cache the dram_type */ | |
| enum mem_type dram_type; | |
| }; | |
| enum err_codes { | |
| DECODE_OK = 0, | |
| ERR_NODE = -1, | |
| ERR_CSROW = -2, | |
| ERR_CHANNEL = -3, | |
| }; | |
| struct err_info { | |
| int err_code; | |
| struct mem_ctl_info *src_mci; | |
| int csrow; | |
| int channel; | |
| u16 syndrome; | |
| u32 page; | |
| u32 offset; | |
| }; | |
| static inline u64 get_dram_base(struct amd64_pvt *pvt, u8 i) | |
| { | |
| u64 addr = ((u64)pvt->ranges[i].base.lo & 0xffff0000) << 8; | |
| if (boot_cpu_data.x86 == 0xf) | |
| return addr; | |
| return (((u64)pvt->ranges[i].base.hi & 0x000000ff) << 40) | addr; | |
| } | |
| static inline u64 get_dram_limit(struct amd64_pvt *pvt, u8 i) | |
| { | |
| u64 lim = (((u64)pvt->ranges[i].lim.lo & 0xffff0000) << 8) | 0x00ffffff; | |
| if (boot_cpu_data.x86 == 0xf) | |
| return lim; | |
| return (((u64)pvt->ranges[i].lim.hi & 0x000000ff) << 40) | lim; | |
| } | |
| static inline u16 extract_syndrome(u64 status) | |
| { | |
| return ((status >> 47) & 0xff) | ((status >> 16) & 0xff00); | |
| } | |
| static inline u8 dct_sel_interleave_addr(struct amd64_pvt *pvt) | |
| { | |
| if (pvt->fam == 0x15 && pvt->model >= 0x30) | |
| return (((pvt->dct_sel_hi >> 9) & 0x1) << 2) | | |
| ((pvt->dct_sel_lo >> 6) & 0x3); | |
| return ((pvt)->dct_sel_lo >> 6) & 0x3; | |
| } | |
| /* | |
| * per-node ECC settings descriptor | |
| */ | |
| struct ecc_settings { | |
| u32 old_nbctl; | |
| bool nbctl_valid; | |
| struct flags { | |
| unsigned long nb_mce_enable:1; | |
| unsigned long nb_ecc_prev:1; | |
| } flags; | |
| }; | |
| #ifdef CONFIG_EDAC_DEBUG | |
| extern const struct attribute_group amd64_edac_dbg_group; | |
| #endif | |
| #ifdef CONFIG_EDAC_AMD64_ERROR_INJECTION | |
| extern const struct attribute_group amd64_edac_inj_group; | |
| #endif | |
| /* | |
| * Each of the PCI Device IDs types have their own set of hardware accessor | |
| * functions and per device encoding/decoding logic. | |
| */ | |
| struct low_ops { | |
| int (*early_channel_count) (struct amd64_pvt *pvt); | |
| void (*map_sysaddr_to_csrow) (struct mem_ctl_info *mci, u64 sys_addr, | |
| struct err_info *); | |
| int (*dbam_to_cs) (struct amd64_pvt *pvt, u8 dct, | |
| unsigned cs_mode, int cs_mask_nr); | |
| }; | |
| struct amd64_family_type { | |
| const char *ctl_name; | |
| u16 f1_id, f2_id; | |
| struct low_ops ops; | |
| }; | |
| int __amd64_read_pci_cfg_dword(struct pci_dev *pdev, int offset, | |
| u32 *val, const char *func); | |
| int __amd64_write_pci_cfg_dword(struct pci_dev *pdev, int offset, | |
| u32 val, const char *func); | |
| #define amd64_read_pci_cfg(pdev, offset, val) \ | |
| __amd64_read_pci_cfg_dword(pdev, offset, val, __func__) | |
| #define amd64_write_pci_cfg(pdev, offset, val) \ | |
| __amd64_write_pci_cfg_dword(pdev, offset, val, __func__) | |
| int amd64_get_dram_hole_info(struct mem_ctl_info *mci, u64 *hole_base, | |
| u64 *hole_offset, u64 *hole_size); | |
| #define to_mci(k) container_of(k, struct mem_ctl_info, dev) | |
| /* Injection helpers */ | |
| static inline void disable_caches(void *dummy) | |
| { | |
| write_cr0(read_cr0() | X86_CR0_CD); | |
| wbinvd(); | |
| } | |
| static inline void enable_caches(void *dummy) | |
| { | |
| write_cr0(read_cr0() & ~X86_CR0_CD); | |
| } | |
| static inline u8 dram_intlv_en(struct amd64_pvt *pvt, unsigned int i) | |
| { | |
| if (pvt->fam == 0x15 && pvt->model >= 0x30) { | |
| u32 tmp; | |
| amd64_read_pci_cfg(pvt->F1, DRAM_CONT_LIMIT, &tmp); | |
| return (u8) tmp & 0xF; | |
| } | |
| return (u8) (pvt->ranges[i].base.lo >> 8) & 0x7; | |
| } | |
| static inline u8 dhar_valid(struct amd64_pvt *pvt) | |
| { | |
| if (pvt->fam == 0x15 && pvt->model >= 0x30) { | |
| u32 tmp; | |
| amd64_read_pci_cfg(pvt->F1, DRAM_CONT_BASE, &tmp); | |
| return (tmp >> 1) & BIT(0); | |
| } | |
| return (pvt)->dhar & BIT(0); | |
| } | |
| static inline u32 dct_sel_baseaddr(struct amd64_pvt *pvt) | |
| { | |
| if (pvt->fam == 0x15 && pvt->model >= 0x30) { | |
| u32 tmp; | |
| amd64_read_pci_cfg(pvt->F1, DRAM_CONT_BASE, &tmp); | |
| return (tmp >> 11) & 0x1FFF; | |
| } | |
| return (pvt)->dct_sel_lo & 0xFFFFF800; | |
| } |