| /* | |
| * GPIO Chip driver for Analog Devices | |
| * ADP5588/ADP5587 I/O Expander and QWERTY Keypad Controller | |
| * | |
| * Copyright 2009-2010 Analog Devices Inc. | |
| * | |
| * Licensed under the GPL-2 or later. | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/kernel.h> | |
| #include <linux/slab.h> | |
| #include <linux/init.h> | |
| #include <linux/i2c.h> | |
| #include <linux/gpio.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/irq.h> | |
| #include <linux/i2c/adp5588.h> | |
| #define DRV_NAME "adp5588-gpio" | |
| /* | |
| * Early pre 4.0 Silicon required to delay readout by at least 25ms, | |
| * since the Event Counter Register updated 25ms after the interrupt | |
| * asserted. | |
| */ | |
| #define WA_DELAYED_READOUT_REVID(rev) ((rev) < 4) | |
| struct adp5588_gpio { | |
| struct i2c_client *client; | |
| struct gpio_chip gpio_chip; | |
| struct mutex lock; /* protect cached dir, dat_out */ | |
| /* protect serialized access to the interrupt controller bus */ | |
| struct mutex irq_lock; | |
| unsigned gpio_start; | |
| unsigned irq_base; | |
| uint8_t dat_out[3]; | |
| uint8_t dir[3]; | |
| uint8_t int_lvl[3]; | |
| uint8_t int_en[3]; | |
| uint8_t irq_mask[3]; | |
| uint8_t irq_stat[3]; | |
| }; | |
| static int adp5588_gpio_read(struct i2c_client *client, u8 reg) | |
| { | |
| int ret = i2c_smbus_read_byte_data(client, reg); | |
| if (ret < 0) | |
| dev_err(&client->dev, "Read Error\n"); | |
| return ret; | |
| } | |
| static int adp5588_gpio_write(struct i2c_client *client, u8 reg, u8 val) | |
| { | |
| int ret = i2c_smbus_write_byte_data(client, reg, val); | |
| if (ret < 0) | |
| dev_err(&client->dev, "Write Error\n"); | |
| return ret; | |
| } | |
| static int adp5588_gpio_get_value(struct gpio_chip *chip, unsigned off) | |
| { | |
| struct adp5588_gpio *dev = gpiochip_get_data(chip); | |
| unsigned bank = ADP5588_BANK(off); | |
| unsigned bit = ADP5588_BIT(off); | |
| int val; | |
| mutex_lock(&dev->lock); | |
| if (dev->dir[bank] & bit) | |
| val = dev->dat_out[bank]; | |
| else | |
| val = adp5588_gpio_read(dev->client, GPIO_DAT_STAT1 + bank); | |
| mutex_unlock(&dev->lock); | |
| return !!(val & bit); | |
| } | |
| static void adp5588_gpio_set_value(struct gpio_chip *chip, | |
| unsigned off, int val) | |
| { | |
| unsigned bank, bit; | |
| struct adp5588_gpio *dev = gpiochip_get_data(chip); | |
| bank = ADP5588_BANK(off); | |
| bit = ADP5588_BIT(off); | |
| mutex_lock(&dev->lock); | |
| if (val) | |
| dev->dat_out[bank] |= bit; | |
| else | |
| dev->dat_out[bank] &= ~bit; | |
| adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank, | |
| dev->dat_out[bank]); | |
| mutex_unlock(&dev->lock); | |
| } | |
| static int adp5588_gpio_direction_input(struct gpio_chip *chip, unsigned off) | |
| { | |
| int ret; | |
| unsigned bank; | |
| struct adp5588_gpio *dev = gpiochip_get_data(chip); | |
| bank = ADP5588_BANK(off); | |
| mutex_lock(&dev->lock); | |
| dev->dir[bank] &= ~ADP5588_BIT(off); | |
| ret = adp5588_gpio_write(dev->client, GPIO_DIR1 + bank, dev->dir[bank]); | |
| mutex_unlock(&dev->lock); | |
| return ret; | |
| } | |
| static int adp5588_gpio_direction_output(struct gpio_chip *chip, | |
| unsigned off, int val) | |
| { | |
| int ret; | |
| unsigned bank, bit; | |
| struct adp5588_gpio *dev = gpiochip_get_data(chip); | |
| bank = ADP5588_BANK(off); | |
| bit = ADP5588_BIT(off); | |
| mutex_lock(&dev->lock); | |
| dev->dir[bank] |= bit; | |
| if (val) | |
| dev->dat_out[bank] |= bit; | |
| else | |
| dev->dat_out[bank] &= ~bit; | |
| ret = adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank, | |
| dev->dat_out[bank]); | |
| ret |= adp5588_gpio_write(dev->client, GPIO_DIR1 + bank, | |
| dev->dir[bank]); | |
| mutex_unlock(&dev->lock); | |
| return ret; | |
| } | |
| #ifdef CONFIG_GPIO_ADP5588_IRQ | |
| static int adp5588_gpio_to_irq(struct gpio_chip *chip, unsigned off) | |
| { | |
| struct adp5588_gpio *dev = gpiochip_get_data(chip); | |
| return dev->irq_base + off; | |
| } | |
| static void adp5588_irq_bus_lock(struct irq_data *d) | |
| { | |
| struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d); | |
| mutex_lock(&dev->irq_lock); | |
| } | |
| /* | |
| * genirq core code can issue chip->mask/unmask from atomic context. | |
| * This doesn't work for slow busses where an access needs to sleep. | |
| * bus_sync_unlock() is therefore called outside the atomic context, | |
| * syncs the current irq mask state with the slow external controller | |
| * and unlocks the bus. | |
| */ | |
| static void adp5588_irq_bus_sync_unlock(struct irq_data *d) | |
| { | |
| struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d); | |
| int i; | |
| for (i = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) | |
| if (dev->int_en[i] ^ dev->irq_mask[i]) { | |
| dev->int_en[i] = dev->irq_mask[i]; | |
| adp5588_gpio_write(dev->client, GPIO_INT_EN1 + i, | |
| dev->int_en[i]); | |
| } | |
| mutex_unlock(&dev->irq_lock); | |
| } | |
| static void adp5588_irq_mask(struct irq_data *d) | |
| { | |
| struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d); | |
| unsigned gpio = d->irq - dev->irq_base; | |
| dev->irq_mask[ADP5588_BANK(gpio)] &= ~ADP5588_BIT(gpio); | |
| } | |
| static void adp5588_irq_unmask(struct irq_data *d) | |
| { | |
| struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d); | |
| unsigned gpio = d->irq - dev->irq_base; | |
| dev->irq_mask[ADP5588_BANK(gpio)] |= ADP5588_BIT(gpio); | |
| } | |
| static int adp5588_irq_set_type(struct irq_data *d, unsigned int type) | |
| { | |
| struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d); | |
| uint16_t gpio = d->irq - dev->irq_base; | |
| unsigned bank, bit; | |
| if ((type & IRQ_TYPE_EDGE_BOTH)) { | |
| dev_err(&dev->client->dev, "irq %d: unsupported type %d\n", | |
| d->irq, type); | |
| return -EINVAL; | |
| } | |
| bank = ADP5588_BANK(gpio); | |
| bit = ADP5588_BIT(gpio); | |
| if (type & IRQ_TYPE_LEVEL_HIGH) | |
| dev->int_lvl[bank] |= bit; | |
| else if (type & IRQ_TYPE_LEVEL_LOW) | |
| dev->int_lvl[bank] &= ~bit; | |
| else | |
| return -EINVAL; | |
| adp5588_gpio_direction_input(&dev->gpio_chip, gpio); | |
| adp5588_gpio_write(dev->client, GPIO_INT_LVL1 + bank, | |
| dev->int_lvl[bank]); | |
| return 0; | |
| } | |
| static struct irq_chip adp5588_irq_chip = { | |
| .name = "adp5588", | |
| .irq_mask = adp5588_irq_mask, | |
| .irq_unmask = adp5588_irq_unmask, | |
| .irq_bus_lock = adp5588_irq_bus_lock, | |
| .irq_bus_sync_unlock = adp5588_irq_bus_sync_unlock, | |
| .irq_set_type = adp5588_irq_set_type, | |
| }; | |
| static int adp5588_gpio_read_intstat(struct i2c_client *client, u8 *buf) | |
| { | |
| int ret = i2c_smbus_read_i2c_block_data(client, GPIO_INT_STAT1, 3, buf); | |
| if (ret < 0) | |
| dev_err(&client->dev, "Read INT_STAT Error\n"); | |
| return ret; | |
| } | |
| static irqreturn_t adp5588_irq_handler(int irq, void *devid) | |
| { | |
| struct adp5588_gpio *dev = devid; | |
| unsigned status, bank, bit, pending; | |
| int ret; | |
| status = adp5588_gpio_read(dev->client, INT_STAT); | |
| if (status & ADP5588_GPI_INT) { | |
| ret = adp5588_gpio_read_intstat(dev->client, dev->irq_stat); | |
| if (ret < 0) | |
| memset(dev->irq_stat, 0, ARRAY_SIZE(dev->irq_stat)); | |
| for (bank = 0, bit = 0; bank <= ADP5588_BANK(ADP5588_MAXGPIO); | |
| bank++, bit = 0) { | |
| pending = dev->irq_stat[bank] & dev->irq_mask[bank]; | |
| while (pending) { | |
| if (pending & (1 << bit)) { | |
| handle_nested_irq(dev->irq_base + | |
| (bank << 3) + bit); | |
| pending &= ~(1 << bit); | |
| } | |
| bit++; | |
| } | |
| } | |
| } | |
| adp5588_gpio_write(dev->client, INT_STAT, status); /* Status is W1C */ | |
| return IRQ_HANDLED; | |
| } | |
| static int adp5588_irq_setup(struct adp5588_gpio *dev) | |
| { | |
| struct i2c_client *client = dev->client; | |
| struct adp5588_gpio_platform_data *pdata = | |
| dev_get_platdata(&client->dev); | |
| unsigned gpio; | |
| int ret; | |
| adp5588_gpio_write(client, CFG, ADP5588_AUTO_INC); | |
| adp5588_gpio_write(client, INT_STAT, -1); /* status is W1C */ | |
| adp5588_gpio_read_intstat(client, dev->irq_stat); /* read to clear */ | |
| dev->irq_base = pdata->irq_base; | |
| mutex_init(&dev->irq_lock); | |
| for (gpio = 0; gpio < dev->gpio_chip.ngpio; gpio++) { | |
| int irq = gpio + dev->irq_base; | |
| irq_set_chip_data(irq, dev); | |
| irq_set_chip_and_handler(irq, &adp5588_irq_chip, | |
| handle_level_irq); | |
| irq_set_nested_thread(irq, 1); | |
| irq_modify_status(irq, IRQ_NOREQUEST, IRQ_NOPROBE); | |
| } | |
| ret = request_threaded_irq(client->irq, | |
| NULL, | |
| adp5588_irq_handler, | |
| IRQF_TRIGGER_FALLING | IRQF_ONESHOT, | |
| dev_name(&client->dev), dev); | |
| if (ret) { | |
| dev_err(&client->dev, "failed to request irq %d\n", | |
| client->irq); | |
| goto out; | |
| } | |
| dev->gpio_chip.to_irq = adp5588_gpio_to_irq; | |
| adp5588_gpio_write(client, CFG, | |
| ADP5588_AUTO_INC | ADP5588_INT_CFG | ADP5588_GPI_INT); | |
| return 0; | |
| out: | |
| dev->irq_base = 0; | |
| return ret; | |
| } | |
| static void adp5588_irq_teardown(struct adp5588_gpio *dev) | |
| { | |
| if (dev->irq_base) | |
| free_irq(dev->client->irq, dev); | |
| } | |
| #else | |
| static int adp5588_irq_setup(struct adp5588_gpio *dev) | |
| { | |
| struct i2c_client *client = dev->client; | |
| dev_warn(&client->dev, "interrupt support not compiled in\n"); | |
| return 0; | |
| } | |
| static void adp5588_irq_teardown(struct adp5588_gpio *dev) | |
| { | |
| } | |
| #endif /* CONFIG_GPIO_ADP5588_IRQ */ | |
| static int adp5588_gpio_probe(struct i2c_client *client, | |
| const struct i2c_device_id *id) | |
| { | |
| struct adp5588_gpio_platform_data *pdata = | |
| dev_get_platdata(&client->dev); | |
| struct adp5588_gpio *dev; | |
| struct gpio_chip *gc; | |
| int ret, i, revid; | |
| if (!pdata) { | |
| dev_err(&client->dev, "missing platform data\n"); | |
| return -ENODEV; | |
| } | |
| if (!i2c_check_functionality(client->adapter, | |
| I2C_FUNC_SMBUS_BYTE_DATA)) { | |
| dev_err(&client->dev, "SMBUS Byte Data not Supported\n"); | |
| return -EIO; | |
| } | |
| dev = devm_kzalloc(&client->dev, sizeof(*dev), GFP_KERNEL); | |
| if (!dev) | |
| return -ENOMEM; | |
| dev->client = client; | |
| gc = &dev->gpio_chip; | |
| gc->direction_input = adp5588_gpio_direction_input; | |
| gc->direction_output = adp5588_gpio_direction_output; | |
| gc->get = adp5588_gpio_get_value; | |
| gc->set = adp5588_gpio_set_value; | |
| gc->can_sleep = true; | |
| gc->base = pdata->gpio_start; | |
| gc->ngpio = ADP5588_MAXGPIO; | |
| gc->label = client->name; | |
| gc->owner = THIS_MODULE; | |
| gc->names = pdata->names; | |
| mutex_init(&dev->lock); | |
| ret = adp5588_gpio_read(dev->client, DEV_ID); | |
| if (ret < 0) | |
| goto err; | |
| revid = ret & ADP5588_DEVICE_ID_MASK; | |
| for (i = 0, ret = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) { | |
| dev->dat_out[i] = adp5588_gpio_read(client, GPIO_DAT_OUT1 + i); | |
| dev->dir[i] = adp5588_gpio_read(client, GPIO_DIR1 + i); | |
| ret |= adp5588_gpio_write(client, KP_GPIO1 + i, 0); | |
| ret |= adp5588_gpio_write(client, GPIO_PULL1 + i, | |
| (pdata->pullup_dis_mask >> (8 * i)) & 0xFF); | |
| ret |= adp5588_gpio_write(client, GPIO_INT_EN1 + i, 0); | |
| if (ret) | |
| goto err; | |
| } | |
| if (pdata->irq_base) { | |
| if (WA_DELAYED_READOUT_REVID(revid)) { | |
| dev_warn(&client->dev, "GPIO int not supported\n"); | |
| } else { | |
| ret = adp5588_irq_setup(dev); | |
| if (ret) | |
| goto err; | |
| } | |
| } | |
| ret = devm_gpiochip_add_data(&client->dev, &dev->gpio_chip, dev); | |
| if (ret) | |
| goto err_irq; | |
| dev_info(&client->dev, "IRQ Base: %d Rev.: %d\n", | |
| pdata->irq_base, revid); | |
| if (pdata->setup) { | |
| ret = pdata->setup(client, gc->base, gc->ngpio, pdata->context); | |
| if (ret < 0) | |
| dev_warn(&client->dev, "setup failed, %d\n", ret); | |
| } | |
| i2c_set_clientdata(client, dev); | |
| return 0; | |
| err_irq: | |
| adp5588_irq_teardown(dev); | |
| err: | |
| return ret; | |
| } | |
| static int adp5588_gpio_remove(struct i2c_client *client) | |
| { | |
| struct adp5588_gpio_platform_data *pdata = | |
| dev_get_platdata(&client->dev); | |
| struct adp5588_gpio *dev = i2c_get_clientdata(client); | |
| int ret; | |
| if (pdata->teardown) { | |
| ret = pdata->teardown(client, | |
| dev->gpio_chip.base, dev->gpio_chip.ngpio, | |
| pdata->context); | |
| if (ret < 0) { | |
| dev_err(&client->dev, "teardown failed %d\n", ret); | |
| return ret; | |
| } | |
| } | |
| if (dev->irq_base) | |
| free_irq(dev->client->irq, dev); | |
| return 0; | |
| } | |
| static const struct i2c_device_id adp5588_gpio_id[] = { | |
| {DRV_NAME, 0}, | |
| {} | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, adp5588_gpio_id); | |
| static struct i2c_driver adp5588_gpio_driver = { | |
| .driver = { | |
| .name = DRV_NAME, | |
| }, | |
| .probe = adp5588_gpio_probe, | |
| .remove = adp5588_gpio_remove, | |
| .id_table = adp5588_gpio_id, | |
| }; | |
| module_i2c_driver(adp5588_gpio_driver); | |
| MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>"); | |
| MODULE_DESCRIPTION("GPIO ADP5588 Driver"); | |
| MODULE_LICENSE("GPL"); |