| /* | |
| * AMD CS5535/CS5536 GPIO driver | |
| * Copyright (C) 2006 Advanced Micro Devices, Inc. | |
| * Copyright (C) 2007-2009 Andres Salomon <dilinger@collabora.co.uk> | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of version 2 of the GNU General Public License | |
| * as published by the Free Software Foundation. | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/spinlock.h> | |
| #include <linux/module.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/gpio.h> | |
| #include <linux/io.h> | |
| #include <linux/cs5535.h> | |
| #include <asm/msr.h> | |
| #define DRV_NAME "cs5535-gpio" | |
| /* | |
| * Some GPIO pins | |
| * 31-29,23 : reserved (always mask out) | |
| * 28 : Power Button | |
| * 26 : PME# | |
| * 22-16 : LPC | |
| * 14,15 : SMBus | |
| * 9,8 : UART1 | |
| * 7 : PCI INTB | |
| * 3,4 : UART2/DDC | |
| * 2 : IDE_IRQ0 | |
| * 1 : AC_BEEP | |
| * 0 : PCI INTA | |
| * | |
| * If a mask was not specified, allow all except | |
| * reserved and Power Button | |
| */ | |
| #define GPIO_DEFAULT_MASK 0x0F7FFFFF | |
| static ulong mask = GPIO_DEFAULT_MASK; | |
| module_param_named(mask, mask, ulong, 0444); | |
| MODULE_PARM_DESC(mask, "GPIO channel mask."); | |
| /* | |
| * FIXME: convert this singleton driver to use the state container | |
| * design pattern, see Documentation/driver-model/design-patterns.txt | |
| */ | |
| static struct cs5535_gpio_chip { | |
| struct gpio_chip chip; | |
| resource_size_t base; | |
| struct platform_device *pdev; | |
| spinlock_t lock; | |
| } cs5535_gpio_chip; | |
| /* | |
| * The CS5535/CS5536 GPIOs support a number of extra features not defined | |
| * by the gpio_chip API, so these are exported. For a full list of the | |
| * registers, see include/linux/cs5535.h. | |
| */ | |
| static void errata_outl(struct cs5535_gpio_chip *chip, u32 val, | |
| unsigned int reg) | |
| { | |
| unsigned long addr = chip->base + 0x80 + reg; | |
| /* | |
| * According to the CS5536 errata (#36), after suspend | |
| * a write to the high bank GPIO register will clear all | |
| * non-selected bits; the recommended workaround is a | |
| * read-modify-write operation. | |
| * | |
| * Don't apply this errata to the edge status GPIOs, as writing | |
| * to their lower bits will clear them. | |
| */ | |
| if (reg != GPIO_POSITIVE_EDGE_STS && reg != GPIO_NEGATIVE_EDGE_STS) { | |
| if (val & 0xffff) | |
| val |= (inl(addr) & 0xffff); /* ignore the high bits */ | |
| else | |
| val |= (inl(addr) ^ (val >> 16)); | |
| } | |
| outl(val, addr); | |
| } | |
| static void __cs5535_gpio_set(struct cs5535_gpio_chip *chip, unsigned offset, | |
| unsigned int reg) | |
| { | |
| if (offset < 16) | |
| /* low bank register */ | |
| outl(1 << offset, chip->base + reg); | |
| else | |
| /* high bank register */ | |
| errata_outl(chip, 1 << (offset - 16), reg); | |
| } | |
| void cs5535_gpio_set(unsigned offset, unsigned int reg) | |
| { | |
| struct cs5535_gpio_chip *chip = &cs5535_gpio_chip; | |
| unsigned long flags; | |
| spin_lock_irqsave(&chip->lock, flags); | |
| __cs5535_gpio_set(chip, offset, reg); | |
| spin_unlock_irqrestore(&chip->lock, flags); | |
| } | |
| EXPORT_SYMBOL_GPL(cs5535_gpio_set); | |
| static void __cs5535_gpio_clear(struct cs5535_gpio_chip *chip, unsigned offset, | |
| unsigned int reg) | |
| { | |
| if (offset < 16) | |
| /* low bank register */ | |
| outl(1 << (offset + 16), chip->base + reg); | |
| else | |
| /* high bank register */ | |
| errata_outl(chip, 1 << offset, reg); | |
| } | |
| void cs5535_gpio_clear(unsigned offset, unsigned int reg) | |
| { | |
| struct cs5535_gpio_chip *chip = &cs5535_gpio_chip; | |
| unsigned long flags; | |
| spin_lock_irqsave(&chip->lock, flags); | |
| __cs5535_gpio_clear(chip, offset, reg); | |
| spin_unlock_irqrestore(&chip->lock, flags); | |
| } | |
| EXPORT_SYMBOL_GPL(cs5535_gpio_clear); | |
| int cs5535_gpio_isset(unsigned offset, unsigned int reg) | |
| { | |
| struct cs5535_gpio_chip *chip = &cs5535_gpio_chip; | |
| unsigned long flags; | |
| long val; | |
| spin_lock_irqsave(&chip->lock, flags); | |
| if (offset < 16) | |
| /* low bank register */ | |
| val = inl(chip->base + reg); | |
| else { | |
| /* high bank register */ | |
| val = inl(chip->base + 0x80 + reg); | |
| offset -= 16; | |
| } | |
| spin_unlock_irqrestore(&chip->lock, flags); | |
| return (val & (1 << offset)) ? 1 : 0; | |
| } | |
| EXPORT_SYMBOL_GPL(cs5535_gpio_isset); | |
| int cs5535_gpio_set_irq(unsigned group, unsigned irq) | |
| { | |
| uint32_t lo, hi; | |
| if (group > 7 || irq > 15) | |
| return -EINVAL; | |
| rdmsr(MSR_PIC_ZSEL_HIGH, lo, hi); | |
| lo &= ~(0xF << (group * 4)); | |
| lo |= (irq & 0xF) << (group * 4); | |
| wrmsr(MSR_PIC_ZSEL_HIGH, lo, hi); | |
| return 0; | |
| } | |
| EXPORT_SYMBOL_GPL(cs5535_gpio_set_irq); | |
| void cs5535_gpio_setup_event(unsigned offset, int pair, int pme) | |
| { | |
| struct cs5535_gpio_chip *chip = &cs5535_gpio_chip; | |
| uint32_t shift = (offset % 8) * 4; | |
| unsigned long flags; | |
| uint32_t val; | |
| if (offset >= 24) | |
| offset = GPIO_MAP_W; | |
| else if (offset >= 16) | |
| offset = GPIO_MAP_Z; | |
| else if (offset >= 8) | |
| offset = GPIO_MAP_Y; | |
| else | |
| offset = GPIO_MAP_X; | |
| spin_lock_irqsave(&chip->lock, flags); | |
| val = inl(chip->base + offset); | |
| /* Clear whatever was there before */ | |
| val &= ~(0xF << shift); | |
| /* Set the new value */ | |
| val |= ((pair & 7) << shift); | |
| /* Set the PME bit if this is a PME event */ | |
| if (pme) | |
| val |= (1 << (shift + 3)); | |
| outl(val, chip->base + offset); | |
| spin_unlock_irqrestore(&chip->lock, flags); | |
| } | |
| EXPORT_SYMBOL_GPL(cs5535_gpio_setup_event); | |
| /* | |
| * Generic gpio_chip API support. | |
| */ | |
| static int chip_gpio_request(struct gpio_chip *c, unsigned offset) | |
| { | |
| struct cs5535_gpio_chip *chip = gpiochip_get_data(c); | |
| unsigned long flags; | |
| spin_lock_irqsave(&chip->lock, flags); | |
| /* check if this pin is available */ | |
| if ((mask & (1 << offset)) == 0) { | |
| dev_info(&chip->pdev->dev, | |
| "pin %u is not available (check mask)\n", offset); | |
| spin_unlock_irqrestore(&chip->lock, flags); | |
| return -EINVAL; | |
| } | |
| /* disable output aux 1 & 2 on this pin */ | |
| __cs5535_gpio_clear(chip, offset, GPIO_OUTPUT_AUX1); | |
| __cs5535_gpio_clear(chip, offset, GPIO_OUTPUT_AUX2); | |
| /* disable input aux 1 on this pin */ | |
| __cs5535_gpio_clear(chip, offset, GPIO_INPUT_AUX1); | |
| spin_unlock_irqrestore(&chip->lock, flags); | |
| return 0; | |
| } | |
| static int chip_gpio_get(struct gpio_chip *chip, unsigned offset) | |
| { | |
| return cs5535_gpio_isset(offset, GPIO_READ_BACK); | |
| } | |
| static void chip_gpio_set(struct gpio_chip *chip, unsigned offset, int val) | |
| { | |
| if (val) | |
| cs5535_gpio_set(offset, GPIO_OUTPUT_VAL); | |
| else | |
| cs5535_gpio_clear(offset, GPIO_OUTPUT_VAL); | |
| } | |
| static int chip_direction_input(struct gpio_chip *c, unsigned offset) | |
| { | |
| struct cs5535_gpio_chip *chip = gpiochip_get_data(c); | |
| unsigned long flags; | |
| spin_lock_irqsave(&chip->lock, flags); | |
| __cs5535_gpio_set(chip, offset, GPIO_INPUT_ENABLE); | |
| __cs5535_gpio_clear(chip, offset, GPIO_OUTPUT_ENABLE); | |
| spin_unlock_irqrestore(&chip->lock, flags); | |
| return 0; | |
| } | |
| static int chip_direction_output(struct gpio_chip *c, unsigned offset, int val) | |
| { | |
| struct cs5535_gpio_chip *chip = gpiochip_get_data(c); | |
| unsigned long flags; | |
| spin_lock_irqsave(&chip->lock, flags); | |
| __cs5535_gpio_set(chip, offset, GPIO_INPUT_ENABLE); | |
| __cs5535_gpio_set(chip, offset, GPIO_OUTPUT_ENABLE); | |
| if (val) | |
| __cs5535_gpio_set(chip, offset, GPIO_OUTPUT_VAL); | |
| else | |
| __cs5535_gpio_clear(chip, offset, GPIO_OUTPUT_VAL); | |
| spin_unlock_irqrestore(&chip->lock, flags); | |
| return 0; | |
| } | |
| static const char * const cs5535_gpio_names[] = { | |
| "GPIO0", "GPIO1", "GPIO2", "GPIO3", | |
| "GPIO4", "GPIO5", "GPIO6", "GPIO7", | |
| "GPIO8", "GPIO9", "GPIO10", "GPIO11", | |
| "GPIO12", "GPIO13", "GPIO14", "GPIO15", | |
| "GPIO16", "GPIO17", "GPIO18", "GPIO19", | |
| "GPIO20", "GPIO21", "GPIO22", NULL, | |
| "GPIO24", "GPIO25", "GPIO26", "GPIO27", | |
| "GPIO28", NULL, NULL, NULL, | |
| }; | |
| static struct cs5535_gpio_chip cs5535_gpio_chip = { | |
| .chip = { | |
| .owner = THIS_MODULE, | |
| .label = DRV_NAME, | |
| .base = 0, | |
| .ngpio = 32, | |
| .names = cs5535_gpio_names, | |
| .request = chip_gpio_request, | |
| .get = chip_gpio_get, | |
| .set = chip_gpio_set, | |
| .direction_input = chip_direction_input, | |
| .direction_output = chip_direction_output, | |
| }, | |
| }; | |
| static int cs5535_gpio_probe(struct platform_device *pdev) | |
| { | |
| struct resource *res; | |
| int err = -EIO; | |
| ulong mask_orig = mask; | |
| /* There are two ways to get the GPIO base address; one is by | |
| * fetching it from MSR_LBAR_GPIO, the other is by reading the | |
| * PCI BAR info. The latter method is easier (especially across | |
| * different architectures), so we'll stick with that for now. If | |
| * it turns out to be unreliable in the face of crappy BIOSes, we | |
| * can always go back to using MSRs.. */ | |
| res = platform_get_resource(pdev, IORESOURCE_IO, 0); | |
| if (!res) { | |
| dev_err(&pdev->dev, "can't fetch device resource info\n"); | |
| return err; | |
| } | |
| if (!devm_request_region(&pdev->dev, res->start, resource_size(res), | |
| pdev->name)) { | |
| dev_err(&pdev->dev, "can't request region\n"); | |
| return err; | |
| } | |
| /* set up the driver-specific struct */ | |
| cs5535_gpio_chip.base = res->start; | |
| cs5535_gpio_chip.pdev = pdev; | |
| spin_lock_init(&cs5535_gpio_chip.lock); | |
| dev_info(&pdev->dev, "reserved resource region %pR\n", res); | |
| /* mask out reserved pins */ | |
| mask &= 0x1F7FFFFF; | |
| /* do not allow pin 28, Power Button, as there's special handling | |
| * in the PMC needed. (note 12, p. 48) */ | |
| mask &= ~(1 << 28); | |
| if (mask_orig != mask) | |
| dev_info(&pdev->dev, "mask changed from 0x%08lX to 0x%08lX\n", | |
| mask_orig, mask); | |
| /* finally, register with the generic GPIO API */ | |
| err = devm_gpiochip_add_data(&pdev->dev, &cs5535_gpio_chip.chip, | |
| &cs5535_gpio_chip); | |
| if (err) | |
| return err; | |
| return 0; | |
| } | |
| static struct platform_driver cs5535_gpio_driver = { | |
| .driver = { | |
| .name = DRV_NAME, | |
| }, | |
| .probe = cs5535_gpio_probe, | |
| }; | |
| module_platform_driver(cs5535_gpio_driver); | |
| MODULE_AUTHOR("Andres Salomon <dilinger@queued.net>"); | |
| MODULE_DESCRIPTION("AMD CS5535/CS5536 GPIO driver"); | |
| MODULE_LICENSE("GPL"); | |
| MODULE_ALIAS("platform:" DRV_NAME); |