| config LEDS_GPIO_REGISTER | |
| bool | |
| help | |
| This option provides the function gpio_led_register_device. | |
| As this function is used by arch code it must not be compiled as a | |
| module. | |
| menuconfig NEW_LEDS | |
| bool "LED Support" | |
| help | |
| Say Y to enable Linux LED support. This allows control of supported | |
| LEDs from both userspace and optionally, by kernel events (triggers). | |
| if NEW_LEDS | |
| config LEDS_CLASS | |
| tristate "LED Class Support" | |
| help | |
| This option enables the led sysfs class in /sys/class/leds. You'll | |
| need this to do anything useful with LEDs. If unsure, say N. | |
| config LEDS_CLASS_FLASH | |
| tristate "LED Flash Class Support" | |
| depends on LEDS_CLASS | |
| help | |
| This option enables the flash led sysfs class in /sys/class/leds. | |
| It wrapps LED Class and adds flash LEDs specific sysfs attributes | |
| and kernel internal API to it. You'll need this to provide support | |
| for the flash related features of a LED device. It can be built | |
| as a module. | |
| comment "LED drivers" | |
| config LEDS_88PM860X | |
| tristate "LED Support for Marvell 88PM860x PMIC" | |
| depends on LEDS_CLASS | |
| depends on MFD_88PM860X | |
| help | |
| This option enables support for on-chip LED drivers found on Marvell | |
| Semiconductor 88PM8606 PMIC. | |
| config LEDS_AAT1290 | |
| tristate "LED support for the AAT1290" | |
| depends on LEDS_CLASS_FLASH | |
| depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS | |
| depends on GPIOLIB || COMPILE_TEST | |
| depends on OF | |
| depends on PINCTRL | |
| help | |
| This option enables support for the LEDs on the AAT1290. | |
| config LEDS_BCM6328 | |
| tristate "LED Support for Broadcom BCM6328" | |
| depends on LEDS_CLASS | |
| depends on HAS_IOMEM | |
| depends on OF | |
| help | |
| This option enables support for LEDs connected to the BCM6328 | |
| LED HW controller accessed via MMIO registers. | |
| config LEDS_BCM6358 | |
| tristate "LED Support for Broadcom BCM6358" | |
| depends on LEDS_CLASS | |
| depends on HAS_IOMEM | |
| depends on OF | |
| help | |
| This option enables support for LEDs connected to the BCM6358 | |
| LED HW controller accessed via MMIO registers. | |
| config LEDS_LM3530 | |
| tristate "LCD Backlight driver for LM3530" | |
| depends on LEDS_CLASS | |
| depends on I2C | |
| help | |
| This option enables support for the LCD backlight using | |
| LM3530 ambient light sensor chip. This ALS chip can be | |
| controlled manually or using PWM input or using ambient | |
| light automatically. | |
| config LEDS_LM3533 | |
| tristate "LED support for LM3533" | |
| depends on LEDS_CLASS | |
| depends on MFD_LM3533 | |
| help | |
| This option enables support for the LEDs on National Semiconductor / | |
| TI LM3533 Lighting Power chips. | |
| The LEDs can be controlled directly, through PWM input, or by the | |
| ambient-light-sensor interface. The chip supports | |
| hardware-accelerated blinking with maximum on and off periods of 9.8 | |
| and 77 seconds respectively. | |
| config LEDS_LM3642 | |
| tristate "LED support for LM3642 Chip" | |
| depends on LEDS_CLASS && I2C | |
| select REGMAP_I2C | |
| help | |
| This option enables support for LEDs connected to LM3642. | |
| The LM3642 is a 4MHz fixed-frequency synchronous boost | |
| converter plus 1.5A constant current driver for a high-current | |
| white LED. | |
| config LEDS_LOCOMO | |
| tristate "LED Support for Locomo device" | |
| depends on LEDS_CLASS | |
| depends on SHARP_LOCOMO | |
| help | |
| This option enables support for the LEDs on Sharp Locomo. | |
| Zaurus models SL-5500 and SL-5600. | |
| config LEDS_MIKROTIK_RB532 | |
| tristate "LED Support for Mikrotik Routerboard 532" | |
| depends on LEDS_CLASS | |
| depends on MIKROTIK_RB532 | |
| help | |
| This option enables support for the so called "User LED" of | |
| Mikrotik's Routerboard 532. | |
| config LEDS_S3C24XX | |
| tristate "LED Support for Samsung S3C24XX GPIO LEDs" | |
| depends on LEDS_CLASS | |
| depends on ARCH_S3C24XX | |
| help | |
| This option enables support for LEDs connected to GPIO lines | |
| on Samsung S3C24XX series CPUs, such as the S3C2410 and S3C2440. | |
| config LEDS_NET48XX | |
| tristate "LED Support for Soekris net48xx series Error LED" | |
| depends on LEDS_CLASS | |
| depends on SCx200_GPIO | |
| help | |
| This option enables support for the Soekris net4801 and net4826 error | |
| LED. | |
| config LEDS_FSG | |
| tristate "LED Support for the Freecom FSG-3" | |
| depends on LEDS_CLASS | |
| depends on MACH_FSG | |
| help | |
| This option enables support for the LEDs on the Freecom FSG-3. | |
| config LEDS_WRAP | |
| tristate "LED Support for the WRAP series LEDs" | |
| depends on LEDS_CLASS | |
| depends on SCx200_GPIO | |
| help | |
| This option enables support for the PCEngines WRAP programmable LEDs. | |
| config LEDS_COBALT_QUBE | |
| tristate "LED Support for the Cobalt Qube series front LED" | |
| depends on LEDS_CLASS | |
| depends on MIPS_COBALT | |
| help | |
| This option enables support for the front LED on Cobalt Qube series | |
| config LEDS_COBALT_RAQ | |
| bool "LED Support for the Cobalt Raq series" | |
| depends on LEDS_CLASS=y && MIPS_COBALT | |
| select LEDS_TRIGGERS | |
| help | |
| This option enables support for the Cobalt Raq series LEDs. | |
| config LEDS_SUNFIRE | |
| tristate "LED support for SunFire servers." | |
| depends on LEDS_CLASS | |
| depends on SPARC64 | |
| select LEDS_TRIGGERS | |
| help | |
| This option enables support for the Left, Middle, and Right | |
| LEDs on the I/O and CPU boards of SunFire UltraSPARC servers. | |
| config LEDS_IPAQ_MICRO | |
| tristate "LED Support for the Compaq iPAQ h3xxx" | |
| depends on LEDS_CLASS | |
| depends on MFD_IPAQ_MICRO | |
| help | |
| Choose this option if you want to use the notification LED on | |
| Compaq/HP iPAQ h3100 and h3600. | |
| config LEDS_HP6XX | |
| tristate "LED Support for the HP Jornada 6xx" | |
| depends on LEDS_CLASS | |
| depends on SH_HP6XX | |
| help | |
| This option enables LED support for the handheld | |
| HP Jornada 620/660/680/690. | |
| config LEDS_PCA9532 | |
| tristate "LED driver for PCA9532 dimmer" | |
| depends on LEDS_CLASS | |
| depends on I2C && INPUT | |
| help | |
| This option enables support for NXP pca9532 | |
| LED controller. It is generally only useful | |
| as a platform driver | |
| config LEDS_PCA9532_GPIO | |
| bool "Enable GPIO support for PCA9532" | |
| depends on LEDS_PCA9532 | |
| depends on GPIOLIB | |
| help | |
| Allow unused pins on PCA9532 to be used as gpio. | |
| To use a pin as gpio pca9532_type in pca9532_platform data needs to | |
| set to PCA9532_TYPE_GPIO. | |
| config LEDS_GPIO | |
| tristate "LED Support for GPIO connected LEDs" | |
| depends on LEDS_CLASS | |
| depends on GPIOLIB || COMPILE_TEST | |
| help | |
| This option enables support for the LEDs connected to GPIO | |
| outputs. To be useful the particular board must have LEDs | |
| and they must be connected to the GPIO lines. The LEDs must be | |
| defined as platform devices and/or OpenFirmware platform devices. | |
| The code to use these bindings can be selected below. | |
| config LEDS_LP3944 | |
| tristate "LED Support for N.S. LP3944 (Fun Light) I2C chip" | |
| depends on LEDS_CLASS | |
| depends on I2C | |
| help | |
| This option enables support for LEDs connected to the National | |
| Semiconductor LP3944 Lighting Management Unit (LMU) also known as | |
| Fun Light Chip. | |
| To compile this driver as a module, choose M here: the | |
| module will be called leds-lp3944. | |
| config LEDS_LP3952 | |
| tristate "LED Support for TI LP3952 2 channel LED driver" | |
| depends on LEDS_CLASS | |
| depends on I2C | |
| depends on ACPI | |
| depends on GPIOLIB | |
| select REGMAP_I2C | |
| help | |
| This option enables support for LEDs connected to the Texas | |
| Instruments LP3952 LED driver. | |
| To compile this driver as a module, choose M here: the | |
| module will be called leds-lp3952. | |
| config LEDS_LP55XX_COMMON | |
| tristate "Common Driver for TI/National LP5521/5523/55231/5562/8501" | |
| depends on LEDS_LP5521 || LEDS_LP5523 || LEDS_LP5562 || LEDS_LP8501 | |
| select FW_LOADER | |
| select FW_LOADER_USER_HELPER | |
| help | |
| This option supports common operations for LP5521/5523/55231/5562/8501 | |
| devices. | |
| config LEDS_LP5521 | |
| tristate "LED Support for N.S. LP5521 LED driver chip" | |
| depends on LEDS_CLASS && I2C | |
| select LEDS_LP55XX_COMMON | |
| help | |
| If you say yes here you get support for the National Semiconductor | |
| LP5521 LED driver. It is 3 channel chip with programmable engines. | |
| Driver provides direct control via LED class and interface for | |
| programming the engines. | |
| config LEDS_LP5523 | |
| tristate "LED Support for TI/National LP5523/55231 LED driver chip" | |
| depends on LEDS_CLASS && I2C | |
| select LEDS_LP55XX_COMMON | |
| help | |
| If you say yes here you get support for TI/National Semiconductor | |
| LP5523/55231 LED driver. | |
| It is 9 channel chip with programmable engines. | |
| Driver provides direct control via LED class and interface for | |
| programming the engines. | |
| config LEDS_LP5562 | |
| tristate "LED Support for TI LP5562 LED driver chip" | |
| depends on LEDS_CLASS && I2C | |
| select LEDS_LP55XX_COMMON | |
| help | |
| If you say yes here you get support for TI LP5562 LED driver. | |
| It is 4 channels chip with programmable engines. | |
| Driver provides direct control via LED class and interface for | |
| programming the engines. | |
| config LEDS_LP8501 | |
| tristate "LED Support for TI LP8501 LED driver chip" | |
| depends on LEDS_CLASS && I2C | |
| select LEDS_LP55XX_COMMON | |
| help | |
| If you say yes here you get support for TI LP8501 LED driver. | |
| It is 9 channel chip with programmable engines. | |
| Driver provides direct control via LED class and interface for | |
| programming the engines. | |
| It is similar as LP5523, but output power selection is available. | |
| And register layout and engine program schemes are different. | |
| config LEDS_LP8788 | |
| tristate "LED support for the TI LP8788 PMIC" | |
| depends on LEDS_CLASS | |
| depends on MFD_LP8788 | |
| help | |
| This option enables support for the Keyboard LEDs on the LP8788 PMIC. | |
| config LEDS_LP8860 | |
| tristate "LED support for the TI LP8860 4 channel LED driver" | |
| depends on LEDS_CLASS && I2C | |
| select REGMAP_I2C | |
| help | |
| If you say yes here you get support for the TI LP8860 4 channel | |
| LED driver. | |
| This option enables support for the display cluster LEDs | |
| on the LP8860 4 channel LED driver using the I2C communication | |
| bus. | |
| config LEDS_CLEVO_MAIL | |
| tristate "Mail LED on Clevo notebook" | |
| depends on LEDS_CLASS | |
| depends on X86 && SERIO_I8042 && DMI | |
| help | |
| This driver makes the mail LED accessible from userspace | |
| programs through the leds subsystem. This LED have three | |
| known mode: off, blink at 0.5Hz and blink at 1Hz. | |
| The driver supports two kinds of interface: using ledtrig-timer | |
| or through /sys/class/leds/clevo::mail/brightness. As this LED | |
| cannot change it's brightness it blinks instead. The brightness | |
| value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means | |
| blink at 1Hz. | |
| This module can drive the mail LED for the following notebooks: | |
| Clevo D400P | |
| Clevo D410J | |
| Clevo D410V | |
| Clevo D400V/D470V (not tested, but might work) | |
| Clevo M540N | |
| Clevo M5x0N (not tested, but might work) | |
| Positivo Mobile (Clevo M5x0V) | |
| If your model is not listed here you can try the "nodetect" | |
| module parameter. | |
| To compile this driver as a module, choose M here: the | |
| module will be called leds-clevo-mail. | |
| config LEDS_PCA955X | |
| tristate "LED Support for PCA955x I2C chips" | |
| depends on LEDS_CLASS | |
| depends on I2C | |
| help | |
| This option enables support for LEDs connected to PCA955x | |
| LED driver chips accessed via the I2C bus. Supported | |
| devices include PCA9550, PCA9551, PCA9552, and PCA9553. | |
| config LEDS_PCA963X | |
| tristate "LED support for PCA963x I2C chip" | |
| depends on LEDS_CLASS | |
| depends on I2C | |
| help | |
| This option enables support for LEDs connected to the PCA963x | |
| LED driver chip accessed via the I2C bus. Supported | |
| devices include PCA9633 and PCA9634 | |
| config LEDS_WM831X_STATUS | |
| tristate "LED support for status LEDs on WM831x PMICs" | |
| depends on LEDS_CLASS | |
| depends on MFD_WM831X | |
| help | |
| This option enables support for the status LEDs of the WM831x | |
| series of PMICs. | |
| config LEDS_WM8350 | |
| tristate "LED Support for WM8350 AudioPlus PMIC" | |
| depends on LEDS_CLASS | |
| depends on MFD_WM8350 | |
| help | |
| This option enables support for LEDs driven by the Wolfson | |
| Microelectronics WM8350 AudioPlus PMIC. | |
| config LEDS_DA903X | |
| tristate "LED Support for DA9030/DA9034 PMIC" | |
| depends on LEDS_CLASS | |
| depends on PMIC_DA903X | |
| help | |
| This option enables support for on-chip LED drivers found | |
| on Dialog Semiconductor DA9030/DA9034 PMICs. | |
| config LEDS_DA9052 | |
| tristate "Dialog DA9052/DA9053 LEDS" | |
| depends on LEDS_CLASS | |
| depends on PMIC_DA9052 | |
| help | |
| This option enables support for on-chip LED drivers found | |
| on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs. | |
| config LEDS_DAC124S085 | |
| tristate "LED Support for DAC124S085 SPI DAC" | |
| depends on LEDS_CLASS | |
| depends on SPI | |
| help | |
| This option enables support for DAC124S085 SPI DAC from NatSemi, | |
| which can be used to control up to four LEDs. | |
| config LEDS_PWM | |
| tristate "PWM driven LED Support" | |
| depends on LEDS_CLASS | |
| depends on PWM | |
| help | |
| This option enables support for pwm driven LEDs | |
| config LEDS_REGULATOR | |
| tristate "REGULATOR driven LED support" | |
| depends on LEDS_CLASS | |
| depends on REGULATOR | |
| help | |
| This option enables support for regulator driven LEDs. | |
| config LEDS_BD2802 | |
| tristate "LED driver for BD2802 RGB LED" | |
| depends on LEDS_CLASS | |
| depends on I2C | |
| help | |
| This option enables support for BD2802GU RGB LED driver chips | |
| accessed via the I2C bus. | |
| config LEDS_INTEL_SS4200 | |
| tristate "LED driver for Intel NAS SS4200 series" | |
| depends on LEDS_CLASS | |
| depends on PCI && DMI | |
| depends on X86 | |
| help | |
| This option enables support for the Intel SS4200 series of | |
| Network Attached Storage servers. You may control the hard | |
| drive or power LEDs on the front panel. Using this driver | |
| can stop the front LED from blinking after startup. | |
| config LEDS_LT3593 | |
| tristate "LED driver for LT3593 controllers" | |
| depends on LEDS_CLASS | |
| depends on GPIOLIB || COMPILE_TEST | |
| help | |
| This option enables support for LEDs driven by a Linear Technology | |
| LT3593 controller. This controller uses a special one-wire pulse | |
| coding protocol to set the brightness. | |
| config LEDS_ADP5520 | |
| tristate "LED Support for ADP5520/ADP5501 PMIC" | |
| depends on LEDS_CLASS | |
| depends on PMIC_ADP5520 | |
| help | |
| This option enables support for on-chip LED drivers found | |
| on Analog Devices ADP5520/ADP5501 PMICs. | |
| To compile this driver as a module, choose M here: the module will | |
| be called leds-adp5520. | |
| config LEDS_DELL_NETBOOKS | |
| tristate "External LED on Dell Business Netbooks" | |
| depends on LEDS_CLASS | |
| depends on X86 && ACPI_WMI | |
| depends on DELL_SMBIOS | |
| help | |
| This adds support for the Latitude 2100 and similar | |
| notebooks that have an external LED. | |
| config LEDS_MC13783 | |
| tristate "LED Support for MC13XXX PMIC" | |
| depends on LEDS_CLASS | |
| depends on MFD_MC13XXX | |
| help | |
| This option enable support for on-chip LED drivers found | |
| on Freescale Semiconductor MC13783/MC13892/MC34708 PMIC. | |
| config LEDS_NS2 | |
| tristate "LED support for Network Space v2 GPIO LEDs" | |
| depends on LEDS_CLASS | |
| depends on MACH_KIRKWOOD || MACH_ARMADA_370 | |
| default y | |
| help | |
| This option enables support for the dual-GPIO LEDs found on the | |
| following LaCie/Seagate boards: | |
| Network Space v2 (and parents: Max, Mini) | |
| Internet Space v2 | |
| d2 Network v2 | |
| n090401 (Seagate NAS 4-Bay) | |
| config LEDS_NETXBIG | |
| tristate "LED support for Big Network series LEDs" | |
| depends on LEDS_CLASS | |
| depends on MACH_KIRKWOOD | |
| default y | |
| help | |
| This option enable support for LEDs found on the LaCie 2Big | |
| and 5Big Network v2 boards. The LEDs are wired to a CPLD and are | |
| controlled through a GPIO extension bus. | |
| config LEDS_ASIC3 | |
| bool "LED support for the HTC ASIC3" | |
| depends on LEDS_CLASS=y | |
| depends on MFD_ASIC3 | |
| default y | |
| help | |
| This option enables support for the LEDs on the HTC ASIC3. The HTC | |
| ASIC3 LED GPIOs are inputs, not outputs, thus the leds-gpio driver | |
| cannot be used. This driver supports hardware blinking with an on+off | |
| period from 62ms to 125s. Say Y to enable LEDs on the HP iPAQ hx4700. | |
| config LEDS_TCA6507 | |
| tristate "LED Support for TCA6507 I2C chip" | |
| depends on LEDS_CLASS && I2C | |
| help | |
| This option enables support for LEDs connected to TC6507 | |
| LED driver chips accessed via the I2C bus. | |
| Driver support brightness control and hardware-assisted blinking. | |
| config LEDS_TLC591XX | |
| tristate "LED driver for TLC59108 and TLC59116 controllers" | |
| depends on LEDS_CLASS && I2C | |
| select REGMAP_I2C | |
| help | |
| This option enables support for Texas Instruments TLC59108 | |
| and TLC59116 LED controllers. | |
| config LEDS_MAX77693 | |
| tristate "LED support for MAX77693 Flash" | |
| depends on LEDS_CLASS_FLASH | |
| depends on V4L2_FLASH_LED_CLASS || !V4L2_FLASH_LED_CLASS | |
| depends on MFD_MAX77693 | |
| depends on OF | |
| help | |
| This option enables support for the flash part of the MAX77693 | |
| multifunction device. It has build in control for two leds in flash | |
| and torch mode. | |
| config LEDS_MAX8997 | |
| tristate "LED support for MAX8997 PMIC" | |
| depends on LEDS_CLASS && MFD_MAX8997 | |
| help | |
| This option enables support for on-chip LED drivers on | |
| MAXIM MAX8997 PMIC. | |
| config LEDS_LM355x | |
| tristate "LED support for LM355x Chips, LM3554 and LM3556" | |
| depends on LEDS_CLASS && I2C | |
| select REGMAP_I2C | |
| help | |
| This option enables support for LEDs connected to LM355x. | |
| LM355x includes Torch, Flash and Indicator functions. | |
| config LEDS_OT200 | |
| tristate "LED support for the Bachmann OT200" | |
| depends on LEDS_CLASS && HAS_IOMEM && (X86_32 || COMPILE_TEST) | |
| help | |
| This option enables support for the LEDs on the Bachmann OT200. | |
| Say Y to enable LEDs on the Bachmann OT200. | |
| config LEDS_MENF21BMC | |
| tristate "LED support for the MEN 14F021P00 BMC" | |
| depends on LEDS_CLASS && MFD_MENF21BMC | |
| help | |
| Say Y here to include support for the MEN 14F021P00 BMC LEDs. | |
| This driver can also be built as a module. If so the module | |
| will be called leds-menf21bmc. | |
| config LEDS_KTD2692 | |
| tristate "LED support for KTD2692 flash LED controller" | |
| depends on LEDS_CLASS_FLASH && OF | |
| depends on GPIOLIB || COMPILE_TEST | |
| help | |
| This option enables support for KTD2692 LED flash connected | |
| through ExpressWire interface. | |
| Say Y to enable this driver. | |
| config LEDS_SEAD3 | |
| tristate "LED support for the MIPS SEAD 3 board" | |
| depends on LEDS_CLASS && MIPS_SEAD3 | |
| help | |
| Say Y here to include support for the FLED and PLED LEDs on SEAD3 eval | |
| boards. | |
| This driver can also be built as a module. If so the module | |
| will be called leds-sead3. | |
| config LEDS_IS31FL319X | |
| tristate "LED Support for ISSI IS31FL319x I2C LED controller family" | |
| depends on LEDS_CLASS && I2C && OF | |
| select REGMAP_I2C | |
| help | |
| This option enables support for LEDs connected to ISSI IS31FL319x | |
| fancy LED driver chips accessed via the I2C bus. | |
| Driver supports individual PWM brightness control for each channel. | |
| This driver can also be built as a module. If so the module will be | |
| called leds-is31fl319x. | |
| config LEDS_IS31FL32XX | |
| tristate "LED support for ISSI IS31FL32XX I2C LED controller family" | |
| depends on LEDS_CLASS && I2C && OF | |
| help | |
| Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx | |
| LED controllers. They are I2C devices with multiple constant-current | |
| channels, each with independent 256-level PWM control. | |
| comment "LED driver for blink(1) USB RGB LED is under Special HID drivers (HID_THINGM)" | |
| config LEDS_BLINKM | |
| tristate "LED support for the BlinkM I2C RGB LED" | |
| depends on LEDS_CLASS | |
| depends on I2C | |
| help | |
| This option enables support for the BlinkM RGB LED connected | |
| through I2C. Say Y to enable support for the BlinkM LED. | |
| config LEDS_POWERNV | |
| tristate "LED support for PowerNV Platform" | |
| depends on LEDS_CLASS | |
| depends on PPC_POWERNV | |
| depends on OF | |
| help | |
| This option enables support for the system LEDs present on | |
| PowerNV platforms. Say 'y' to enable this support in kernel. | |
| To compile this driver as a module, choose 'm' here: the module | |
| will be called leds-powernv. | |
| config LEDS_SYSCON | |
| bool "LED support for LEDs on system controllers" | |
| depends on LEDS_CLASS=y | |
| depends on MFD_SYSCON | |
| depends on OF | |
| help | |
| This option enabled support for the LEDs on syscon type | |
| devices. This will only work with device tree enabled | |
| devices. | |
| config LEDS_VERSATILE | |
| tristate "LED support for the ARM Versatile and RealView" | |
| depends on ARCH_REALVIEW || ARCH_VERSATILE | |
| depends on LEDS_CLASS | |
| help | |
| This option enabled support for the LEDs on the ARM Versatile | |
| and RealView boards. Say Y to enabled these. | |
| config LEDS_PM8058 | |
| tristate "LED Support for the Qualcomm PM8058 PMIC" | |
| depends on MFD_PM8921_CORE | |
| depends on LEDS_CLASS | |
| help | |
| Choose this option if you want to use the LED drivers in | |
| the Qualcomm PM8058 PMIC. | |
| config LEDS_MLXCPLD | |
| tristate "LED support for the Mellanox boards" | |
| depends on X86_64 && DMI | |
| depends on LEDS_CLASS | |
| help | |
| This option enabled support for the LEDs on the Mellanox | |
| boards. Say Y to enabled these. | |
| comment "LED Triggers" | |
| source "drivers/leds/trigger/Kconfig" | |
| endif # NEW_LEDS |