| /* | |
| * Copyright (c) 2008-2011 Atheros Communications Inc. | |
| * | |
| * Permission to use, copy, modify, and/or distribute this software for any | |
| * purpose with or without fee is hereby granted, provided that the above | |
| * copyright notice and this permission notice appear in all copies. | |
| * | |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES | |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF | |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR | |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES | |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN | |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF | |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. | |
| */ | |
| #include <linux/moduleparam.h> | |
| #include "hw.h" | |
| #include "ar5008_initvals.h" | |
| #include "ar9001_initvals.h" | |
| #include "ar9002_initvals.h" | |
| #include "ar9002_phy.h" | |
| /* General hardware code for the A5008/AR9001/AR9002 hadware families */ | |
| static int ar9002_hw_init_mode_regs(struct ath_hw *ah) | |
| { | |
| if (AR_SREV_9271(ah)) { | |
| INIT_INI_ARRAY(&ah->iniModes, ar9271Modes_9271); | |
| INIT_INI_ARRAY(&ah->iniCommon, ar9271Common_9271); | |
| INIT_INI_ARRAY(&ah->iniModes_9271_ANI_reg, ar9271Modes_9271_ANI_reg); | |
| return 0; | |
| } | |
| INIT_INI_ARRAY(&ah->iniPcieSerdes, | |
| ar9280PciePhy_clkreq_always_on_L1_9280); | |
| if (AR_SREV_9287_11_OR_LATER(ah)) { | |
| INIT_INI_ARRAY(&ah->iniModes, ar9287Modes_9287_1_1); | |
| INIT_INI_ARRAY(&ah->iniCommon, ar9287Common_9287_1_1); | |
| } else if (AR_SREV_9285_12_OR_LATER(ah)) { | |
| INIT_INI_ARRAY(&ah->iniModes, ar9285Modes_9285_1_2); | |
| INIT_INI_ARRAY(&ah->iniCommon, ar9285Common_9285_1_2); | |
| } else if (AR_SREV_9280_20_OR_LATER(ah)) { | |
| INIT_INI_ARRAY(&ah->iniModes, ar9280Modes_9280_2); | |
| INIT_INI_ARRAY(&ah->iniCommon, ar9280Common_9280_2); | |
| INIT_INI_ARRAY(&ah->iniModesFastClock, | |
| ar9280Modes_fast_clock_9280_2); | |
| } else if (AR_SREV_9160_10_OR_LATER(ah)) { | |
| INIT_INI_ARRAY(&ah->iniModes, ar5416Modes_9160); | |
| INIT_INI_ARRAY(&ah->iniCommon, ar5416Common_9160); | |
| if (AR_SREV_9160_11(ah)) { | |
| INIT_INI_ARRAY(&ah->iniAddac, | |
| ar5416Addac_9160_1_1); | |
| } else { | |
| INIT_INI_ARRAY(&ah->iniAddac, ar5416Addac_9160); | |
| } | |
| } else if (AR_SREV_9100_OR_LATER(ah)) { | |
| INIT_INI_ARRAY(&ah->iniModes, ar5416Modes_9100); | |
| INIT_INI_ARRAY(&ah->iniCommon, ar5416Common_9100); | |
| INIT_INI_ARRAY(&ah->iniAddac, ar5416Addac_9100); | |
| } else { | |
| INIT_INI_ARRAY(&ah->iniModes, ar5416Modes); | |
| INIT_INI_ARRAY(&ah->iniCommon, ar5416Common); | |
| INIT_INI_ARRAY(&ah->iniAddac, ar5416Addac); | |
| } | |
| if (!AR_SREV_9280_20_OR_LATER(ah)) { | |
| /* Common for AR5416, AR913x, AR9160 */ | |
| INIT_INI_ARRAY(&ah->iniBB_RfGain, ar5416BB_RfGain); | |
| /* Common for AR913x, AR9160 */ | |
| if (!AR_SREV_5416(ah)) | |
| INIT_INI_ARRAY(&ah->iniBank6, ar5416Bank6TPC_9100); | |
| else | |
| INIT_INI_ARRAY(&ah->iniBank6, ar5416Bank6TPC); | |
| } | |
| /* iniAddac needs to be modified for these chips */ | |
| if (AR_SREV_9160(ah) || !AR_SREV_5416_22_OR_LATER(ah)) { | |
| struct ar5416IniArray *addac = &ah->iniAddac; | |
| u32 size = sizeof(u32) * addac->ia_rows * addac->ia_columns; | |
| u32 *data; | |
| data = devm_kzalloc(ah->dev, size, GFP_KERNEL); | |
| if (!data) | |
| return -ENOMEM; | |
| memcpy(data, addac->ia_array, size); | |
| addac->ia_array = data; | |
| if (!AR_SREV_5416_22_OR_LATER(ah)) { | |
| /* override CLKDRV value */ | |
| INI_RA(addac, 31,1) = 0; | |
| } | |
| } | |
| if (AR_SREV_9287_11_OR_LATER(ah)) { | |
| INIT_INI_ARRAY(&ah->iniCckfirNormal, | |
| ar9287Common_normal_cck_fir_coeff_9287_1_1); | |
| INIT_INI_ARRAY(&ah->iniCckfirJapan2484, | |
| ar9287Common_japan_2484_cck_fir_coeff_9287_1_1); | |
| } | |
| return 0; | |
| } | |
| static void ar9280_20_hw_init_rxgain_ini(struct ath_hw *ah) | |
| { | |
| u32 rxgain_type; | |
| if (ah->eep_ops->get_eeprom(ah, EEP_MINOR_REV) >= | |
| AR5416_EEP_MINOR_VER_17) { | |
| rxgain_type = ah->eep_ops->get_eeprom(ah, EEP_RXGAIN_TYPE); | |
| if (rxgain_type == AR5416_EEP_RXGAIN_13DB_BACKOFF) | |
| INIT_INI_ARRAY(&ah->iniModesRxGain, | |
| ar9280Modes_backoff_13db_rxgain_9280_2); | |
| else if (rxgain_type == AR5416_EEP_RXGAIN_23DB_BACKOFF) | |
| INIT_INI_ARRAY(&ah->iniModesRxGain, | |
| ar9280Modes_backoff_23db_rxgain_9280_2); | |
| else | |
| INIT_INI_ARRAY(&ah->iniModesRxGain, | |
| ar9280Modes_original_rxgain_9280_2); | |
| } else { | |
| INIT_INI_ARRAY(&ah->iniModesRxGain, | |
| ar9280Modes_original_rxgain_9280_2); | |
| } | |
| } | |
| static void ar9280_20_hw_init_txgain_ini(struct ath_hw *ah, u32 txgain_type) | |
| { | |
| if (ah->eep_ops->get_eeprom(ah, EEP_MINOR_REV) >= | |
| AR5416_EEP_MINOR_VER_19) { | |
| if (txgain_type == AR5416_EEP_TXGAIN_HIGH_POWER) | |
| INIT_INI_ARRAY(&ah->iniModesTxGain, | |
| ar9280Modes_high_power_tx_gain_9280_2); | |
| else | |
| INIT_INI_ARRAY(&ah->iniModesTxGain, | |
| ar9280Modes_original_tx_gain_9280_2); | |
| } else { | |
| INIT_INI_ARRAY(&ah->iniModesTxGain, | |
| ar9280Modes_original_tx_gain_9280_2); | |
| } | |
| } | |
| static void ar9271_hw_init_txgain_ini(struct ath_hw *ah, u32 txgain_type) | |
| { | |
| if (txgain_type == AR5416_EEP_TXGAIN_HIGH_POWER) | |
| INIT_INI_ARRAY(&ah->iniModesTxGain, | |
| ar9271Modes_high_power_tx_gain_9271); | |
| else | |
| INIT_INI_ARRAY(&ah->iniModesTxGain, | |
| ar9271Modes_normal_power_tx_gain_9271); | |
| } | |
| static void ar9002_hw_init_mode_gain_regs(struct ath_hw *ah) | |
| { | |
| u32 txgain_type = ah->eep_ops->get_eeprom(ah, EEP_TXGAIN_TYPE); | |
| if (AR_SREV_9287_11_OR_LATER(ah)) | |
| INIT_INI_ARRAY(&ah->iniModesRxGain, | |
| ar9287Modes_rx_gain_9287_1_1); | |
| else if (AR_SREV_9280_20(ah)) | |
| ar9280_20_hw_init_rxgain_ini(ah); | |
| if (AR_SREV_9271(ah)) { | |
| ar9271_hw_init_txgain_ini(ah, txgain_type); | |
| } else if (AR_SREV_9287_11_OR_LATER(ah)) { | |
| INIT_INI_ARRAY(&ah->iniModesTxGain, | |
| ar9287Modes_tx_gain_9287_1_1); | |
| } else if (AR_SREV_9280_20(ah)) { | |
| ar9280_20_hw_init_txgain_ini(ah, txgain_type); | |
| } else if (AR_SREV_9285_12_OR_LATER(ah)) { | |
| /* txgain table */ | |
| if (txgain_type == AR5416_EEP_TXGAIN_HIGH_POWER) { | |
| if (AR_SREV_9285E_20(ah)) { | |
| INIT_INI_ARRAY(&ah->iniModesTxGain, | |
| ar9285Modes_XE2_0_high_power); | |
| } else { | |
| INIT_INI_ARRAY(&ah->iniModesTxGain, | |
| ar9285Modes_high_power_tx_gain_9285_1_2); | |
| } | |
| } else { | |
| if (AR_SREV_9285E_20(ah)) { | |
| INIT_INI_ARRAY(&ah->iniModesTxGain, | |
| ar9285Modes_XE2_0_normal_power); | |
| } else { | |
| INIT_INI_ARRAY(&ah->iniModesTxGain, | |
| ar9285Modes_original_tx_gain_9285_1_2); | |
| } | |
| } | |
| } | |
| } | |
| /* | |
| * Helper for ASPM support. | |
| * | |
| * Disable PLL when in L0s as well as receiver clock when in L1. | |
| * This power saving option must be enabled through the SerDes. | |
| * | |
| * Programming the SerDes must go through the same 288 bit serial shift | |
| * register as the other analog registers. Hence the 9 writes. | |
| */ | |
| static void ar9002_hw_configpcipowersave(struct ath_hw *ah, | |
| bool power_off) | |
| { | |
| u8 i; | |
| u32 val; | |
| /* Nothing to do on restore for 11N */ | |
| if (!power_off /* !restore */) { | |
| if (AR_SREV_9280_20_OR_LATER(ah)) { | |
| /* | |
| * AR9280 2.0 or later chips use SerDes values from the | |
| * initvals.h initialized depending on chipset during | |
| * __ath9k_hw_init() | |
| */ | |
| for (i = 0; i < ah->iniPcieSerdes.ia_rows; i++) { | |
| REG_WRITE(ah, INI_RA(&ah->iniPcieSerdes, i, 0), | |
| INI_RA(&ah->iniPcieSerdes, i, 1)); | |
| } | |
| } else { | |
| ENABLE_REGWRITE_BUFFER(ah); | |
| REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fc00); | |
| REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924); | |
| /* RX shut off when elecidle is asserted */ | |
| REG_WRITE(ah, AR_PCIE_SERDES, 0x28000039); | |
| REG_WRITE(ah, AR_PCIE_SERDES, 0x53160824); | |
| REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980579); | |
| /* | |
| * Ignore ah->ah_config.pcie_clock_req setting for | |
| * pre-AR9280 11n | |
| */ | |
| REG_WRITE(ah, AR_PCIE_SERDES, 0x001defff); | |
| REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40); | |
| REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554); | |
| REG_WRITE(ah, AR_PCIE_SERDES, 0x000e3007); | |
| /* Load the new settings */ | |
| REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000); | |
| REGWRITE_BUFFER_FLUSH(ah); | |
| } | |
| udelay(1000); | |
| } | |
| if (power_off) { | |
| /* clear bit 19 to disable L1 */ | |
| REG_CLR_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA); | |
| val = REG_READ(ah, AR_WA); | |
| /* | |
| * Set PCIe workaround bits | |
| * In AR9280 and AR9285, bit 14 in WA register (disable L1) | |
| * should only be set when device enters D3 and be | |
| * cleared when device comes back to D0. | |
| */ | |
| if (ah->config.pcie_waen) { | |
| if (ah->config.pcie_waen & AR_WA_D3_L1_DISABLE) | |
| val |= AR_WA_D3_L1_DISABLE; | |
| } else { | |
| if (AR_SREV_9285(ah) || AR_SREV_9271(ah) || AR_SREV_9287(ah)) { | |
| if (AR9285_WA_DEFAULT & AR_WA_D3_L1_DISABLE) | |
| val |= AR_WA_D3_L1_DISABLE; | |
| } else if (AR_SREV_9280(ah)) { | |
| if (AR9280_WA_DEFAULT & AR_WA_D3_L1_DISABLE) | |
| val |= AR_WA_D3_L1_DISABLE; | |
| } | |
| } | |
| if (AR_SREV_9280(ah) || AR_SREV_9285(ah) || AR_SREV_9287(ah)) { | |
| /* | |
| * Disable bit 6 and 7 before entering D3 to | |
| * prevent system hang. | |
| */ | |
| val &= ~(AR_WA_BIT6 | AR_WA_BIT7); | |
| } | |
| if (AR_SREV_9280(ah)) | |
| val |= AR_WA_BIT22; | |
| if (AR_SREV_9285E_20(ah)) | |
| val |= AR_WA_BIT23; | |
| REG_WRITE(ah, AR_WA, val); | |
| } else { | |
| if (ah->config.pcie_waen) { | |
| val = ah->config.pcie_waen; | |
| val &= (~AR_WA_D3_L1_DISABLE); | |
| } else { | |
| if (AR_SREV_9285(ah) || AR_SREV_9271(ah) || AR_SREV_9287(ah)) { | |
| val = AR9285_WA_DEFAULT; | |
| val &= (~AR_WA_D3_L1_DISABLE); | |
| } else if (AR_SREV_9280(ah)) { | |
| /* | |
| * For AR9280 chips, bit 22 of 0x4004 | |
| * needs to be set. | |
| */ | |
| val = AR9280_WA_DEFAULT; | |
| val &= (~AR_WA_D3_L1_DISABLE); | |
| } else { | |
| val = AR_WA_DEFAULT; | |
| } | |
| } | |
| /* WAR for ASPM system hang */ | |
| if (AR_SREV_9285(ah) || AR_SREV_9287(ah)) | |
| val |= (AR_WA_BIT6 | AR_WA_BIT7); | |
| if (AR_SREV_9285E_20(ah)) | |
| val |= AR_WA_BIT23; | |
| REG_WRITE(ah, AR_WA, val); | |
| /* set bit 19 to allow forcing of pcie core into L1 state */ | |
| REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA); | |
| } | |
| } | |
| static int ar9002_hw_get_radiorev(struct ath_hw *ah) | |
| { | |
| u32 val; | |
| int i; | |
| ENABLE_REGWRITE_BUFFER(ah); | |
| REG_WRITE(ah, AR_PHY(0x36), 0x00007058); | |
| for (i = 0; i < 8; i++) | |
| REG_WRITE(ah, AR_PHY(0x20), 0x00010000); | |
| REGWRITE_BUFFER_FLUSH(ah); | |
| val = (REG_READ(ah, AR_PHY(256)) >> 24) & 0xff; | |
| val = ((val & 0xf0) >> 4) | ((val & 0x0f) << 4); | |
| return ath9k_hw_reverse_bits(val, 8); | |
| } | |
| int ar9002_hw_rf_claim(struct ath_hw *ah) | |
| { | |
| u32 val; | |
| REG_WRITE(ah, AR_PHY(0), 0x00000007); | |
| val = ar9002_hw_get_radiorev(ah); | |
| switch (val & AR_RADIO_SREV_MAJOR) { | |
| case 0: | |
| val = AR_RAD5133_SREV_MAJOR; | |
| break; | |
| case AR_RAD5133_SREV_MAJOR: | |
| case AR_RAD5122_SREV_MAJOR: | |
| case AR_RAD2133_SREV_MAJOR: | |
| case AR_RAD2122_SREV_MAJOR: | |
| break; | |
| default: | |
| ath_err(ath9k_hw_common(ah), | |
| "Radio Chip Rev 0x%02X not supported\n", | |
| val & AR_RADIO_SREV_MAJOR); | |
| return -EOPNOTSUPP; | |
| } | |
| ah->hw_version.analog5GhzRev = val; | |
| return 0; | |
| } | |
| void ar9002_hw_enable_async_fifo(struct ath_hw *ah) | |
| { | |
| if (AR_SREV_9287_13_OR_LATER(ah)) { | |
| REG_SET_BIT(ah, AR_MAC_PCU_ASYNC_FIFO_REG3, | |
| AR_MAC_PCU_ASYNC_FIFO_REG3_DATAPATH_SEL); | |
| REG_SET_BIT(ah, AR_PHY_MODE, AR_PHY_MODE_ASYNCFIFO); | |
| REG_CLR_BIT(ah, AR_MAC_PCU_ASYNC_FIFO_REG3, | |
| AR_MAC_PCU_ASYNC_FIFO_REG3_SOFT_RESET); | |
| REG_SET_BIT(ah, AR_MAC_PCU_ASYNC_FIFO_REG3, | |
| AR_MAC_PCU_ASYNC_FIFO_REG3_SOFT_RESET); | |
| } | |
| } | |
| static void ar9002_hw_init_hang_checks(struct ath_hw *ah) | |
| { | |
| if (AR_SREV_9100(ah) || AR_SREV_9160(ah)) { | |
| ah->config.hw_hang_checks |= HW_BB_RIFS_HANG; | |
| ah->config.hw_hang_checks |= HW_BB_DFS_HANG; | |
| } | |
| if (AR_SREV_9280(ah)) | |
| ah->config.hw_hang_checks |= HW_BB_RX_CLEAR_STUCK_HANG; | |
| if (AR_SREV_5416(ah) || AR_SREV_9100(ah) || AR_SREV_9160(ah)) | |
| ah->config.hw_hang_checks |= HW_MAC_HANG; | |
| } | |
| /* Sets up the AR5008/AR9001/AR9002 hardware familiy callbacks */ | |
| int ar9002_hw_attach_ops(struct ath_hw *ah) | |
| { | |
| struct ath_hw_private_ops *priv_ops = ath9k_hw_private_ops(ah); | |
| struct ath_hw_ops *ops = ath9k_hw_ops(ah); | |
| int ret; | |
| ret = ar9002_hw_init_mode_regs(ah); | |
| if (ret) | |
| return ret; | |
| priv_ops->init_mode_gain_regs = ar9002_hw_init_mode_gain_regs; | |
| priv_ops->init_hang_checks = ar9002_hw_init_hang_checks; | |
| ops->config_pci_powersave = ar9002_hw_configpcipowersave; | |
| ret = ar5008_hw_attach_phy_ops(ah); | |
| if (ret) | |
| return ret; | |
| if (AR_SREV_9280_20_OR_LATER(ah)) | |
| ar9002_hw_attach_phy_ops(ah); | |
| ar9002_hw_attach_calib_ops(ah); | |
| ar9002_hw_attach_mac_ops(ah); | |
| return 0; | |
| } | |
| void ar9002_hw_load_ani_reg(struct ath_hw *ah, struct ath9k_channel *chan) | |
| { | |
| u32 modesIndex; | |
| int i; | |
| if (IS_CHAN_5GHZ(chan)) | |
| modesIndex = IS_CHAN_HT40(chan) ? 2 : 1; | |
| else | |
| modesIndex = IS_CHAN_HT40(chan) ? 3 : 4; | |
| ENABLE_REGWRITE_BUFFER(ah); | |
| for (i = 0; i < ah->iniModes_9271_ANI_reg.ia_rows; i++) { | |
| u32 reg = INI_RA(&ah->iniModes_9271_ANI_reg, i, 0); | |
| u32 val = INI_RA(&ah->iniModes_9271_ANI_reg, i, modesIndex); | |
| u32 val_orig; | |
| if (reg == AR_PHY_CCK_DETECT) { | |
| val_orig = REG_READ(ah, reg); | |
| val &= AR_PHY_CCK_DETECT_WEAK_SIG_THR_CCK; | |
| val_orig &= ~AR_PHY_CCK_DETECT_WEAK_SIG_THR_CCK; | |
| REG_WRITE(ah, reg, val|val_orig); | |
| } else | |
| REG_WRITE(ah, reg, val); | |
| } | |
| REGWRITE_BUFFER_FLUSH(ah); | |
| } |