| /* hermes.h | |
| * | |
| * Driver core for the "Hermes" wireless MAC controller, as used in | |
| * the Lucent Orinoco and Cabletron RoamAbout cards. It should also | |
| * work on the hfa3841 and hfa3842 MAC controller chips used in the | |
| * Prism I & II chipsets. | |
| * | |
| * This is not a complete driver, just low-level access routines for | |
| * the MAC controller itself. | |
| * | |
| * Based on the prism2 driver from Absolute Value Systems' linux-wlan | |
| * project, the Linux wvlan_cs driver, Lucent's HCF-Light | |
| * (wvlan_hcf.c) library, and the NetBSD wireless driver. | |
| * | |
| * Copyright (C) 2000, David Gibson, Linuxcare Australia. | |
| * (C) Copyright David Gibson, IBM Corp. 2001-2003. | |
| * | |
| * Portions taken from hfa384x.h. | |
| * Copyright (C) 1999 AbsoluteValue Systems, Inc. All Rights Reserved. | |
| * | |
| * This file distributed under the GPL, version 2. | |
| */ | |
| #ifndef _HERMES_H | |
| #define _HERMES_H | |
| /* Notes on locking: | |
| * | |
| * As a module of low level hardware access routines, there is no | |
| * locking. Users of this module should ensure that they serialize | |
| * access to the hermes structure, and to the hardware | |
| */ | |
| #include <linux/if_ether.h> | |
| #include <linux/io.h> | |
| /* | |
| * Limits and constants | |
| */ | |
| #define HERMES_ALLOC_LEN_MIN (4) | |
| #define HERMES_ALLOC_LEN_MAX (2400) | |
| #define HERMES_LTV_LEN_MAX (34) | |
| #define HERMES_BAP_DATALEN_MAX (4096) | |
| #define HERMES_BAP_OFFSET_MAX (4096) | |
| #define HERMES_PORTID_MAX (7) | |
| #define HERMES_NUMPORTS_MAX (HERMES_PORTID_MAX + 1) | |
| #define HERMES_PDR_LEN_MAX (260) /* in bytes, from EK */ | |
| #define HERMES_PDA_RECS_MAX (200) /* a guess */ | |
| #define HERMES_PDA_LEN_MAX (1024) /* in bytes, from EK */ | |
| #define HERMES_SCANRESULT_MAX (35) | |
| #define HERMES_CHINFORESULT_MAX (8) | |
| #define HERMES_MAX_MULTICAST (16) | |
| #define HERMES_MAGIC (0x7d1f) | |
| /* | |
| * Hermes register offsets | |
| */ | |
| #define HERMES_CMD (0x00) | |
| #define HERMES_PARAM0 (0x02) | |
| #define HERMES_PARAM1 (0x04) | |
| #define HERMES_PARAM2 (0x06) | |
| #define HERMES_STATUS (0x08) | |
| #define HERMES_RESP0 (0x0A) | |
| #define HERMES_RESP1 (0x0C) | |
| #define HERMES_RESP2 (0x0E) | |
| #define HERMES_INFOFID (0x10) | |
| #define HERMES_RXFID (0x20) | |
| #define HERMES_ALLOCFID (0x22) | |
| #define HERMES_TXCOMPLFID (0x24) | |
| #define HERMES_SELECT0 (0x18) | |
| #define HERMES_OFFSET0 (0x1C) | |
| #define HERMES_DATA0 (0x36) | |
| #define HERMES_SELECT1 (0x1A) | |
| #define HERMES_OFFSET1 (0x1E) | |
| #define HERMES_DATA1 (0x38) | |
| #define HERMES_EVSTAT (0x30) | |
| #define HERMES_INTEN (0x32) | |
| #define HERMES_EVACK (0x34) | |
| #define HERMES_CONTROL (0x14) | |
| #define HERMES_SWSUPPORT0 (0x28) | |
| #define HERMES_SWSUPPORT1 (0x2A) | |
| #define HERMES_SWSUPPORT2 (0x2C) | |
| #define HERMES_AUXPAGE (0x3A) | |
| #define HERMES_AUXOFFSET (0x3C) | |
| #define HERMES_AUXDATA (0x3E) | |
| /* | |
| * CMD register bitmasks | |
| */ | |
| #define HERMES_CMD_BUSY (0x8000) | |
| #define HERMES_CMD_AINFO (0x7f00) | |
| #define HERMES_CMD_MACPORT (0x0700) | |
| #define HERMES_CMD_RECL (0x0100) | |
| #define HERMES_CMD_WRITE (0x0100) | |
| #define HERMES_CMD_PROGMODE (0x0300) | |
| #define HERMES_CMD_CMDCODE (0x003f) | |
| /* | |
| * STATUS register bitmasks | |
| */ | |
| #define HERMES_STATUS_RESULT (0x7f00) | |
| #define HERMES_STATUS_CMDCODE (0x003f) | |
| /* | |
| * OFFSET register bitmasks | |
| */ | |
| #define HERMES_OFFSET_BUSY (0x8000) | |
| #define HERMES_OFFSET_ERR (0x4000) | |
| #define HERMES_OFFSET_DATAOFF (0x0ffe) | |
| /* | |
| * Event register bitmasks (INTEN, EVSTAT, EVACK) | |
| */ | |
| #define HERMES_EV_TICK (0x8000) | |
| #define HERMES_EV_WTERR (0x4000) | |
| #define HERMES_EV_INFDROP (0x2000) | |
| #define HERMES_EV_INFO (0x0080) | |
| #define HERMES_EV_DTIM (0x0020) | |
| #define HERMES_EV_CMD (0x0010) | |
| #define HERMES_EV_ALLOC (0x0008) | |
| #define HERMES_EV_TXEXC (0x0004) | |
| #define HERMES_EV_TX (0x0002) | |
| #define HERMES_EV_RX (0x0001) | |
| /* | |
| * Command codes | |
| */ | |
| /*--- Controller Commands ----------------------------*/ | |
| #define HERMES_CMD_INIT (0x0000) | |
| #define HERMES_CMD_ENABLE (0x0001) | |
| #define HERMES_CMD_DISABLE (0x0002) | |
| #define HERMES_CMD_DIAG (0x0003) | |
| /*--- Buffer Mgmt Commands ---------------------------*/ | |
| #define HERMES_CMD_ALLOC (0x000A) | |
| #define HERMES_CMD_TX (0x000B) | |
| /*--- Regulate Commands ------------------------------*/ | |
| #define HERMES_CMD_NOTIFY (0x0010) | |
| #define HERMES_CMD_INQUIRE (0x0011) | |
| /*--- Configure Commands -----------------------------*/ | |
| #define HERMES_CMD_ACCESS (0x0021) | |
| #define HERMES_CMD_DOWNLD (0x0022) | |
| /*--- Serial I/O Commands ----------------------------*/ | |
| #define HERMES_CMD_READMIF (0x0030) | |
| #define HERMES_CMD_WRITEMIF (0x0031) | |
| /*--- Debugging Commands -----------------------------*/ | |
| #define HERMES_CMD_TEST (0x0038) | |
| /* Test command arguments */ | |
| #define HERMES_TEST_SET_CHANNEL 0x0800 | |
| #define HERMES_TEST_MONITOR 0x0b00 | |
| #define HERMES_TEST_STOP 0x0f00 | |
| /* Authentication algorithms */ | |
| #define HERMES_AUTH_OPEN 1 | |
| #define HERMES_AUTH_SHARED_KEY 2 | |
| /* WEP settings */ | |
| #define HERMES_WEP_PRIVACY_INVOKED 0x0001 | |
| #define HERMES_WEP_EXCL_UNENCRYPTED 0x0002 | |
| #define HERMES_WEP_HOST_ENCRYPT 0x0010 | |
| #define HERMES_WEP_HOST_DECRYPT 0x0080 | |
| /* Symbol hostscan options */ | |
| #define HERMES_HOSTSCAN_SYMBOL_5SEC 0x0001 | |
| #define HERMES_HOSTSCAN_SYMBOL_ONCE 0x0002 | |
| #define HERMES_HOSTSCAN_SYMBOL_PASSIVE 0x0040 | |
| #define HERMES_HOSTSCAN_SYMBOL_BCAST 0x0080 | |
| /* | |
| * Frame structures and constants | |
| */ | |
| #define HERMES_DESCRIPTOR_OFFSET 0 | |
| #define HERMES_802_11_OFFSET (14) | |
| #define HERMES_802_3_OFFSET (14 + 32) | |
| #define HERMES_802_2_OFFSET (14 + 32 + 14) | |
| #define HERMES_TXCNTL2_OFFSET (HERMES_802_3_OFFSET - 2) | |
| #define HERMES_RXSTAT_ERR (0x0003) | |
| #define HERMES_RXSTAT_BADCRC (0x0001) | |
| #define HERMES_RXSTAT_UNDECRYPTABLE (0x0002) | |
| #define HERMES_RXSTAT_MIC (0x0010) /* Frame contains MIC */ | |
| #define HERMES_RXSTAT_MACPORT (0x0700) | |
| #define HERMES_RXSTAT_PCF (0x1000) /* Frame was received in CF period */ | |
| #define HERMES_RXSTAT_MIC_KEY_ID (0x1800) /* MIC key used */ | |
| #define HERMES_RXSTAT_MSGTYPE (0xE000) | |
| #define HERMES_RXSTAT_1042 (0x2000) /* RFC-1042 frame */ | |
| #define HERMES_RXSTAT_TUNNEL (0x4000) /* bridge-tunnel encoded frame */ | |
| #define HERMES_RXSTAT_WMP (0x6000) /* Wavelan-II Management Protocol frame */ | |
| /* Shift amount for key ID in RXSTAT and TXCTRL */ | |
| #define HERMES_MIC_KEY_ID_SHIFT 11 | |
| struct hermes_tx_descriptor { | |
| __le16 status; | |
| __le16 reserved1; | |
| __le16 reserved2; | |
| __le32 sw_support; | |
| u8 retry_count; | |
| u8 tx_rate; | |
| __le16 tx_control; | |
| } __packed; | |
| #define HERMES_TXSTAT_RETRYERR (0x0001) | |
| #define HERMES_TXSTAT_AGEDERR (0x0002) | |
| #define HERMES_TXSTAT_DISCON (0x0004) | |
| #define HERMES_TXSTAT_FORMERR (0x0008) | |
| #define HERMES_TXCTRL_TX_OK (0x0002) /* ?? interrupt on Tx complete */ | |
| #define HERMES_TXCTRL_TX_EX (0x0004) /* ?? interrupt on Tx exception */ | |
| #define HERMES_TXCTRL_802_11 (0x0008) /* We supply 802.11 header */ | |
| #define HERMES_TXCTRL_MIC (0x0010) /* 802.3 + TKIP */ | |
| #define HERMES_TXCTRL_MIC_KEY_ID (0x1800) /* MIC Key ID mask */ | |
| #define HERMES_TXCTRL_ALT_RTRY (0x0020) | |
| /* Inquiry constants and data types */ | |
| #define HERMES_INQ_TALLIES (0xF100) | |
| #define HERMES_INQ_SCAN (0xF101) | |
| #define HERMES_INQ_CHANNELINFO (0xF102) | |
| #define HERMES_INQ_HOSTSCAN (0xF103) | |
| #define HERMES_INQ_HOSTSCAN_SYMBOL (0xF104) | |
| #define HERMES_INQ_LINKSTATUS (0xF200) | |
| #define HERMES_INQ_SEC_STAT_AGERE (0xF202) | |
| struct hermes_tallies_frame { | |
| __le16 TxUnicastFrames; | |
| __le16 TxMulticastFrames; | |
| __le16 TxFragments; | |
| __le16 TxUnicastOctets; | |
| __le16 TxMulticastOctets; | |
| __le16 TxDeferredTransmissions; | |
| __le16 TxSingleRetryFrames; | |
| __le16 TxMultipleRetryFrames; | |
| __le16 TxRetryLimitExceeded; | |
| __le16 TxDiscards; | |
| __le16 RxUnicastFrames; | |
| __le16 RxMulticastFrames; | |
| __le16 RxFragments; | |
| __le16 RxUnicastOctets; | |
| __le16 RxMulticastOctets; | |
| __le16 RxFCSErrors; | |
| __le16 RxDiscards_NoBuffer; | |
| __le16 TxDiscardsWrongSA; | |
| __le16 RxWEPUndecryptable; | |
| __le16 RxMsgInMsgFragments; | |
| __le16 RxMsgInBadMsgFragments; | |
| /* Those last are probably not available in very old firmwares */ | |
| __le16 RxDiscards_WEPICVError; | |
| __le16 RxDiscards_WEPExcluded; | |
| } __packed; | |
| /* Grabbed from wlan-ng - Thanks Mark... - Jean II | |
| * This is the result of a scan inquiry command */ | |
| /* Structure describing info about an Access Point */ | |
| struct prism2_scan_apinfo { | |
| __le16 channel; /* Channel where the AP sits */ | |
| __le16 noise; /* Noise level */ | |
| __le16 level; /* Signal level */ | |
| u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ | |
| __le16 beacon_interv; /* Beacon interval */ | |
| __le16 capabilities; /* Capabilities */ | |
| __le16 essid_len; /* ESSID length */ | |
| u8 essid[32]; /* ESSID of the network */ | |
| u8 rates[10]; /* Bit rate supported */ | |
| __le16 proberesp_rate; /* Data rate of the response frame */ | |
| __le16 atim; /* ATIM window time, Kus (hostscan only) */ | |
| } __packed; | |
| /* Same stuff for the Lucent/Agere card. | |
| * Thanks to h1kari <h1kari AT dachb0den.com> - Jean II */ | |
| struct agere_scan_apinfo { | |
| __le16 channel; /* Channel where the AP sits */ | |
| __le16 noise; /* Noise level */ | |
| __le16 level; /* Signal level */ | |
| u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ | |
| __le16 beacon_interv; /* Beacon interval */ | |
| __le16 capabilities; /* Capabilities */ | |
| /* bits: 0-ess, 1-ibss, 4-privacy [wep] */ | |
| __le16 essid_len; /* ESSID length */ | |
| u8 essid[32]; /* ESSID of the network */ | |
| } __packed; | |
| /* Moustafa: Scan structure for Symbol cards */ | |
| struct symbol_scan_apinfo { | |
| u8 channel; /* Channel where the AP sits */ | |
| u8 unknown1; /* 8 in 2.9x and 3.9x f/w, 0 otherwise */ | |
| __le16 noise; /* Noise level */ | |
| __le16 level; /* Signal level */ | |
| u8 bssid[ETH_ALEN]; /* MAC address of the Access Point */ | |
| __le16 beacon_interv; /* Beacon interval */ | |
| __le16 capabilities; /* Capabilities */ | |
| /* bits: 0-ess, 1-ibss, 4-privacy [wep] */ | |
| __le16 essid_len; /* ESSID length */ | |
| u8 essid[32]; /* ESSID of the network */ | |
| __le16 rates[5]; /* Bit rate supported */ | |
| __le16 basic_rates; /* Basic rates bitmask */ | |
| u8 unknown2[6]; /* Always FF:FF:FF:FF:00:00 */ | |
| u8 unknown3[8]; /* Always 0, appeared in f/w 3.91-68 */ | |
| } __packed; | |
| union hermes_scan_info { | |
| struct agere_scan_apinfo a; | |
| struct prism2_scan_apinfo p; | |
| struct symbol_scan_apinfo s; | |
| }; | |
| /* Extended scan struct for HERMES_INQ_CHANNELINFO. | |
| * wl_lkm calls this an ACS scan (Automatic Channel Select). | |
| * Keep out of union hermes_scan_info because it is much bigger than | |
| * the older scan structures. */ | |
| struct agere_ext_scan_info { | |
| __le16 reserved0; | |
| u8 noise; | |
| u8 level; | |
| u8 rx_flow; | |
| u8 rate; | |
| __le16 reserved1[2]; | |
| __le16 frame_control; | |
| __le16 dur_id; | |
| u8 addr1[ETH_ALEN]; | |
| u8 addr2[ETH_ALEN]; | |
| u8 bssid[ETH_ALEN]; | |
| __le16 sequence; | |
| u8 addr4[ETH_ALEN]; | |
| __le16 data_length; | |
| /* Next 3 fields do not get filled in. */ | |
| u8 daddr[ETH_ALEN]; | |
| u8 saddr[ETH_ALEN]; | |
| __le16 len_type; | |
| __le64 timestamp; | |
| __le16 beacon_interval; | |
| __le16 capabilities; | |
| u8 data[0]; | |
| } __packed; | |
| #define HERMES_LINKSTATUS_NOT_CONNECTED (0x0000) | |
| #define HERMES_LINKSTATUS_CONNECTED (0x0001) | |
| #define HERMES_LINKSTATUS_DISCONNECTED (0x0002) | |
| #define HERMES_LINKSTATUS_AP_CHANGE (0x0003) | |
| #define HERMES_LINKSTATUS_AP_OUT_OF_RANGE (0x0004) | |
| #define HERMES_LINKSTATUS_AP_IN_RANGE (0x0005) | |
| #define HERMES_LINKSTATUS_ASSOC_FAILED (0x0006) | |
| struct hermes_linkstatus { | |
| __le16 linkstatus; /* Link status */ | |
| } __packed; | |
| struct hermes_response { | |
| u16 status, resp0, resp1, resp2; | |
| }; | |
| /* "ID" structure - used for ESSID and station nickname */ | |
| struct hermes_idstring { | |
| __le16 len; | |
| __le16 val[16]; | |
| } __packed; | |
| struct hermes_multicast { | |
| u8 addr[HERMES_MAX_MULTICAST][ETH_ALEN]; | |
| } __packed; | |
| /* Timeouts */ | |
| #define HERMES_BAP_BUSY_TIMEOUT (10000) /* In iterations of ~1us */ | |
| struct hermes; | |
| /* Functions to access hardware */ | |
| struct hermes_ops { | |
| int (*init)(struct hermes *hw); | |
| int (*cmd_wait)(struct hermes *hw, u16 cmd, u16 parm0, | |
| struct hermes_response *resp); | |
| int (*init_cmd_wait)(struct hermes *hw, u16 cmd, | |
| u16 parm0, u16 parm1, u16 parm2, | |
| struct hermes_response *resp); | |
| int (*allocate)(struct hermes *hw, u16 size, u16 *fid); | |
| int (*read_ltv)(struct hermes *hw, int bap, u16 rid, unsigned buflen, | |
| u16 *length, void *buf); | |
| int (*write_ltv)(struct hermes *hw, int bap, u16 rid, | |
| u16 length, const void *value); | |
| int (*bap_pread)(struct hermes *hw, int bap, void *buf, int len, | |
| u16 id, u16 offset); | |
| int (*bap_pwrite)(struct hermes *hw, int bap, const void *buf, | |
| int len, u16 id, u16 offset); | |
| int (*read_pda)(struct hermes *hw, __le16 *pda, | |
| u32 pda_addr, u16 pda_len); | |
| int (*program_init)(struct hermes *hw, u32 entry_point); | |
| int (*program_end)(struct hermes *hw); | |
| int (*program)(struct hermes *hw, const char *buf, | |
| u32 addr, u32 len); | |
| void (*lock_irqsave)(spinlock_t *lock, unsigned long *flags); | |
| void (*unlock_irqrestore)(spinlock_t *lock, unsigned long *flags); | |
| void (*lock_irq)(spinlock_t *lock); | |
| void (*unlock_irq)(spinlock_t *lock); | |
| }; | |
| /* Basic control structure */ | |
| struct hermes { | |
| void __iomem *iobase; | |
| int reg_spacing; | |
| #define HERMES_16BIT_REGSPACING 0 | |
| #define HERMES_32BIT_REGSPACING 1 | |
| u16 inten; /* Which interrupts should be enabled? */ | |
| bool eeprom_pda; | |
| const struct hermes_ops *ops; | |
| void *priv; | |
| }; | |
| /* Register access convenience macros */ | |
| #define hermes_read_reg(hw, off) \ | |
| (ioread16((hw)->iobase + ((off) << (hw)->reg_spacing))) | |
| #define hermes_write_reg(hw, off, val) \ | |
| (iowrite16((val), (hw)->iobase + ((off) << (hw)->reg_spacing))) | |
| #define hermes_read_regn(hw, name) hermes_read_reg((hw), HERMES_##name) | |
| #define hermes_write_regn(hw, name, val) \ | |
| hermes_write_reg((hw), HERMES_##name, (val)) | |
| /* Function prototypes */ | |
| void hermes_struct_init(struct hermes *hw, void __iomem *address, | |
| int reg_spacing); | |
| /* Inline functions */ | |
| static inline int hermes_present(struct hermes *hw) | |
| { | |
| return hermes_read_regn(hw, SWSUPPORT0) == HERMES_MAGIC; | |
| } | |
| static inline void hermes_set_irqmask(struct hermes *hw, u16 events) | |
| { | |
| hw->inten = events; | |
| hermes_write_regn(hw, INTEN, events); | |
| } | |
| static inline int hermes_enable_port(struct hermes *hw, int port) | |
| { | |
| return hw->ops->cmd_wait(hw, HERMES_CMD_ENABLE | (port << 8), | |
| 0, NULL); | |
| } | |
| static inline int hermes_disable_port(struct hermes *hw, int port) | |
| { | |
| return hw->ops->cmd_wait(hw, HERMES_CMD_DISABLE | (port << 8), | |
| 0, NULL); | |
| } | |
| /* Initiate an INQUIRE command (tallies or scan). The result will come as an | |
| * information frame in __orinoco_ev_info() */ | |
| static inline int hermes_inquire(struct hermes *hw, u16 rid) | |
| { | |
| return hw->ops->cmd_wait(hw, HERMES_CMD_INQUIRE, rid, NULL); | |
| } | |
| #define HERMES_BYTES_TO_RECLEN(n) ((((n) + 1) / 2) + 1) | |
| #define HERMES_RECLEN_TO_BYTES(n) (((n) - 1) * 2) | |
| /* Note that for the next two, the count is in 16-bit words, not bytes */ | |
| static inline void hermes_read_words(struct hermes *hw, int off, | |
| void *buf, unsigned count) | |
| { | |
| off = off << hw->reg_spacing; | |
| ioread16_rep(hw->iobase + off, buf, count); | |
| } | |
| static inline void hermes_write_bytes(struct hermes *hw, int off, | |
| const char *buf, unsigned count) | |
| { | |
| off = off << hw->reg_spacing; | |
| iowrite16_rep(hw->iobase + off, buf, count >> 1); | |
| if (unlikely(count & 1)) | |
| iowrite8(buf[count - 1], hw->iobase + off); | |
| } | |
| static inline void hermes_clear_words(struct hermes *hw, int off, | |
| unsigned count) | |
| { | |
| unsigned i; | |
| off = off << hw->reg_spacing; | |
| for (i = 0; i < count; i++) | |
| iowrite16(0, hw->iobase + off); | |
| } | |
| #define HERMES_READ_RECORD(hw, bap, rid, buf) \ | |
| (hw->ops->read_ltv((hw), (bap), (rid), sizeof(*buf), NULL, (buf))) | |
| #define HERMES_WRITE_RECORD(hw, bap, rid, buf) \ | |
| (hw->ops->write_ltv((hw), (bap), (rid), \ | |
| HERMES_BYTES_TO_RECLEN(sizeof(*buf)), (buf))) | |
| static inline int hermes_read_wordrec(struct hermes *hw, int bap, u16 rid, | |
| u16 *word) | |
| { | |
| __le16 rec; | |
| int err; | |
| err = HERMES_READ_RECORD(hw, bap, rid, &rec); | |
| *word = le16_to_cpu(rec); | |
| return err; | |
| } | |
| static inline int hermes_write_wordrec(struct hermes *hw, int bap, u16 rid, | |
| u16 word) | |
| { | |
| __le16 rec = cpu_to_le16(word); | |
| return HERMES_WRITE_RECORD(hw, bap, rid, &rec); | |
| } | |
| #endif /* _HERMES_H */ |