| # | |
| # PCCARD (PCMCIA/CardBus) bus subsystem configuration | |
| # | |
| menuconfig PCCARD | |
| tristate "PCCard (PCMCIA/CardBus) support" | |
| ---help--- | |
| Say Y here if you want to attach PCMCIA- or PC-cards to your Linux | |
| computer. These are credit-card size devices such as network cards, | |
| modems or hard drives often used with laptops computers. There are | |
| actually two varieties of these cards: 16 bit PCMCIA and 32 bit | |
| CardBus cards. | |
| To compile this driver as modules, choose M here: the | |
| module will be called pcmcia_core. | |
| if PCCARD | |
| config PCMCIA | |
| tristate "16-bit PCMCIA support" | |
| select CRC32 | |
| default y | |
| ---help--- | |
| This option enables support for 16-bit PCMCIA cards. Most older | |
| PC-cards are such 16-bit PCMCIA cards, so unless you know you're | |
| only using 32-bit CardBus cards, say Y or M here. | |
| To use 16-bit PCMCIA cards, you will need supporting software in | |
| most cases. (see the file <file:Documentation/Changes> for | |
| location and details). | |
| To compile this driver as modules, choose M here: the | |
| module will be called pcmcia. | |
| If unsure, say Y. | |
| config PCMCIA_LOAD_CIS | |
| bool "Load CIS updates from userspace" | |
| depends on PCMCIA | |
| select FW_LOADER | |
| default y | |
| help | |
| Some PCMCIA cards require an updated Card Information Structure (CIS) | |
| to be loaded from userspace to work correctly. If you say Y here, | |
| and your userspace is arranged correctly, this will be loaded | |
| automatically using the in-kernel firmware loader and the hotplug | |
| subsystem, instead of relying on cardmgr from pcmcia-cs to do so. | |
| If unsure, say Y. | |
| config CARDBUS | |
| bool "32-bit CardBus support" | |
| depends on PCI | |
| default y | |
| ---help--- | |
| CardBus is a bus mastering architecture for PC-cards, which allows | |
| for 32 bit PC-cards (the original PCMCIA standard specifies only | |
| a 16 bit wide bus). Many newer PC-cards are actually CardBus cards. | |
| To use 32 bit PC-cards, you also need a CardBus compatible host | |
| bridge. Virtually all modern PCMCIA bridges do this, and most of | |
| them are "yenta-compatible", so say Y or M there, too. | |
| If unsure, say Y. | |
| comment "PC-card bridges" | |
| config YENTA | |
| tristate "CardBus yenta-compatible bridge support" | |
| depends on PCI | |
| select CARDBUS if !EXPERT | |
| select PCCARD_NONSTATIC if PCMCIA != n | |
| ---help--- | |
| This option enables support for CardBus host bridges. Virtually | |
| all modern PCMCIA bridges are CardBus compatible. A "bridge" is | |
| the hardware inside your computer that PCMCIA cards are plugged | |
| into. | |
| To compile this driver as modules, choose M here: the | |
| module will be called yenta_socket. | |
| If unsure, say Y. | |
| config YENTA_O2 | |
| default y | |
| bool "Special initialization for O2Micro bridges" if EXPERT | |
| depends on YENTA | |
| config YENTA_RICOH | |
| default y | |
| bool "Special initialization for Ricoh bridges" if EXPERT | |
| depends on YENTA | |
| config YENTA_TI | |
| default y | |
| bool "Special initialization for TI and EnE bridges" if EXPERT | |
| depends on YENTA | |
| config YENTA_ENE_TUNE | |
| default y | |
| bool "Auto-tune EnE bridges for CB cards" if EXPERT | |
| depends on YENTA_TI && CARDBUS | |
| config YENTA_TOSHIBA | |
| default y | |
| bool "Special initialization for Toshiba ToPIC bridges" if EXPERT | |
| depends on YENTA | |
| config PD6729 | |
| tristate "Cirrus PD6729 compatible bridge support" | |
| depends on PCMCIA && PCI | |
| select PCCARD_NONSTATIC | |
| help | |
| This provides support for the Cirrus PD6729 PCI-to-PCMCIA bridge | |
| device, found in some older laptops and PCMCIA card readers. | |
| config I82092 | |
| tristate "i82092 compatible bridge support" | |
| depends on PCMCIA && PCI | |
| select PCCARD_NONSTATIC | |
| help | |
| This provides support for the Intel I82092AA PCI-to-PCMCIA bridge device, | |
| found in some older laptops and more commonly in evaluation boards for the | |
| chip. | |
| config I82365 | |
| tristate "i82365 compatible bridge support" | |
| depends on PCMCIA && ISA | |
| select PCCARD_NONSTATIC | |
| help | |
| Say Y here to include support for ISA-bus PCMCIA host bridges that | |
| are register compatible with the Intel i82365. These are found on | |
| older laptops and ISA-bus card readers for desktop systems. A | |
| "bridge" is the hardware inside your computer that PCMCIA cards are | |
| plugged into. If unsure, say N. | |
| config TCIC | |
| tristate "Databook TCIC host bridge support" | |
| depends on PCMCIA && ISA | |
| select PCCARD_NONSTATIC | |
| help | |
| Say Y here to include support for the Databook TCIC family of PCMCIA | |
| host bridges. These are only found on a handful of old systems. | |
| "Bridge" is the name used for the hardware inside your computer that | |
| PCMCIA cards are plugged into. If unsure, say N. | |
| config PCMCIA_ALCHEMY_DEVBOARD | |
| tristate "Alchemy Db/Pb1xxx PCMCIA socket services" | |
| depends on MIPS_ALCHEMY && PCMCIA | |
| help | |
| Enable this driver of you want PCMCIA support on your Alchemy | |
| Db1000, Db/Pb1100, Db/Pb1500, Db/Pb1550, Db/Pb1200, DB1300 | |
| board. NOT suitable for the PB1000! | |
| This driver is also available as a module called db1xxx_ss.ko | |
| config PCMCIA_XXS1500 | |
| tristate "MyCable XXS1500 PCMCIA socket support" | |
| depends on PCMCIA && MIPS_XXS1500 | |
| help | |
| Support for the PCMCIA/CF socket interface on MyCable XXS1500 | |
| systems. | |
| This driver is also available as a module called xxs1500_ss.ko | |
| config PCMCIA_BCM63XX | |
| tristate "bcm63xx pcmcia support" | |
| depends on BCM63XX && PCMCIA | |
| config PCMCIA_SOC_COMMON | |
| tristate | |
| config PCMCIA_SA11XX_BASE | |
| tristate | |
| config PCMCIA_SA1100 | |
| tristate "SA1100 support" | |
| depends on ARM && ARCH_SA1100 && PCMCIA | |
| select PCMCIA_SOC_COMMON | |
| select PCMCIA_SA11XX_BASE | |
| help | |
| Say Y here to include support for SA11x0-based PCMCIA or CF | |
| sockets, found on HP iPAQs, Yopy, and other StrongARM(R)/ | |
| Xscale(R) embedded machines. | |
| This driver is also available as a module called sa1100_cs. | |
| config PCMCIA_SA1111 | |
| tristate "SA1111 support" | |
| depends on ARM && SA1111 && PCMCIA | |
| select PCMCIA_SOC_COMMON | |
| select PCMCIA_SA11XX_BASE if ARCH_SA1100 | |
| select PCMCIA_PXA2XX if ARCH_LUBBOCK && SA1111 | |
| help | |
| Say Y here to include support for SA1111-based PCMCIA or CF | |
| sockets, found on the Jornada 720, Graphicsmaster and other | |
| StrongARM(R)/Xscale(R) embedded machines. | |
| This driver is also available as a module called sa1111_cs. | |
| config PCMCIA_PXA2XX | |
| tristate "PXA2xx support" | |
| depends on ARM && ARCH_PXA && PCMCIA | |
| depends on (ARCH_LUBBOCK || MACH_MAINSTONE || PXA_SHARPSL \ | |
| || MACH_ARMCORE || ARCH_PXA_PALM || TRIZEPS_PCMCIA \ | |
| || ARCOM_PCMCIA || ARCH_PXA_ESERIES || MACH_STARGATE2 \ | |
| || MACH_VPAC270 || MACH_BALLOON3 || MACH_COLIBRI \ | |
| || MACH_COLIBRI320 || MACH_H4700) | |
| select PCMCIA_SOC_COMMON | |
| help | |
| Say Y here to include support for the PXA2xx PCMCIA controller | |
| config PCMCIA_DEBUG | |
| bool "Enable debugging" | |
| depends on (PCMCIA_SA1111 || PCMCIA_SA1100 || PCMCIA_PXA2XX) | |
| help | |
| Say Y here to enable debugging for the SoC PCMCIA layer. | |
| You will need to choose the debugging level either via the | |
| kernel command line, or module options depending whether | |
| you build the drivers as modules. | |
| The kernel command line options are: | |
| sa11xx_core.pc_debug=N | |
| pxa2xx_core.pc_debug=N | |
| The module option is called pc_debug=N | |
| In all the above examples, N is the debugging verbosity | |
| level. | |
| config PCMCIA_PROBE | |
| bool | |
| default y if ISA && !ARCH_SA1100 && !PARISC | |
| config M32R_PCC | |
| bool "M32R PCMCIA I/F" | |
| depends on M32R && CHIP_M32700 && PCMCIA | |
| help | |
| Say Y here to use the M32R PCMCIA controller. | |
| config M32R_CFC | |
| bool "M32R CF I/F Controller" | |
| depends on M32R && (PLAT_USRV || PLAT_M32700UT || PLAT_MAPPI2 || PLAT_MAPPI3 || PLAT_OPSPUT) | |
| help | |
| Say Y here to use the M32R CompactFlash controller. | |
| config M32R_CFC_NUM | |
| int "M32R CF I/F number" | |
| depends on M32R_CFC | |
| default "1" if PLAT_USRV || PLAT_M32700UT || PLAT_MAPPI2 || PLAT_MAPPI3 || PLAT_OPSPUT | |
| help | |
| Set the number of M32R CF slots. | |
| config PCMCIA_VRC4171 | |
| tristate "NEC VRC4171 Card Controllers support" | |
| depends on CPU_VR41XX && ISA && PCMCIA | |
| config PCMCIA_VRC4173 | |
| tristate "NEC VRC4173 CARDU support" | |
| depends on CPU_VR41XX && PCI && PCMCIA | |
| config OMAP_CF | |
| tristate "OMAP CompactFlash Controller" | |
| depends on PCMCIA && ARCH_OMAP16XX | |
| help | |
| Say Y here to support the CompactFlash controller on OMAP. | |
| Note that this doesn't support "True IDE" mode. | |
| config BFIN_CFPCMCIA | |
| tristate "Blackfin CompactFlash PCMCIA Driver" | |
| depends on PCMCIA && BLACKFIN | |
| help | |
| Say Y here to support the CompactFlash PCMCIA driver for Blackfin. | |
| config AT91_CF | |
| tristate "AT91 CompactFlash Controller" | |
| depends on PCI | |
| depends on PCMCIA && ARCH_AT91 | |
| help | |
| Say Y here to support the CompactFlash controller on AT91 chips. | |
| Or choose M to compile the driver as a module named "at91_cf". | |
| config ELECTRA_CF | |
| tristate "Electra CompactFlash Controller" | |
| depends on PCMCIA && PPC_PASEMI | |
| help | |
| Say Y here to support the CompactFlash controller on the | |
| PA Semi Electra eval board. | |
| config PCCARD_NONSTATIC | |
| bool | |
| config PCCARD_IODYN | |
| bool | |
| endif # PCCARD |