| /* | |
| * Copyright (c) 2013-2015, Linux Foundation. All rights reserved. | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License version 2 and | |
| * only version 2 as published by the Free Software Foundation. | |
| * | |
| * This program is distributed in the hope that it will be useful, | |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| * GNU General Public License for more details. | |
| * | |
| */ | |
| #ifndef UFS_QCOM_PHY_QMP_20NM_H_ | |
| #define UFS_QCOM_PHY_QMP_20NM_H_ | |
| #include "phy-qcom-ufs-i.h" | |
| /* QCOM UFS PHY control registers */ | |
| #define COM_OFF(x) (0x000 + x) | |
| #define PHY_OFF(x) (0xC00 + x) | |
| #define TX_OFF(n, x) (0x400 + (0x400 * n) + x) | |
| #define RX_OFF(n, x) (0x600 + (0x400 * n) + x) | |
| /* UFS PHY PLL block registers */ | |
| #define QSERDES_COM_SYS_CLK_CTRL COM_OFF(0x0) | |
| #define QSERDES_COM_PLL_VCOTAIL_EN COM_OFF(0x04) | |
| #define QSERDES_COM_PLL_CNTRL COM_OFF(0x14) | |
| #define QSERDES_COM_PLL_IP_SETI COM_OFF(0x24) | |
| #define QSERDES_COM_CORE_CLK_IN_SYNC_SEL COM_OFF(0x28) | |
| #define QSERDES_COM_BIAS_EN_CLKBUFLR_EN COM_OFF(0x30) | |
| #define QSERDES_COM_PLL_CP_SETI COM_OFF(0x34) | |
| #define QSERDES_COM_PLL_IP_SETP COM_OFF(0x38) | |
| #define QSERDES_COM_PLL_CP_SETP COM_OFF(0x3C) | |
| #define QSERDES_COM_SYSCLK_EN_SEL_TXBAND COM_OFF(0x48) | |
| #define QSERDES_COM_RESETSM_CNTRL COM_OFF(0x4C) | |
| #define QSERDES_COM_RESETSM_CNTRL2 COM_OFF(0x50) | |
| #define QSERDES_COM_PLLLOCK_CMP1 COM_OFF(0x90) | |
| #define QSERDES_COM_PLLLOCK_CMP2 COM_OFF(0x94) | |
| #define QSERDES_COM_PLLLOCK_CMP3 COM_OFF(0x98) | |
| #define QSERDES_COM_PLLLOCK_CMP_EN COM_OFF(0x9C) | |
| #define QSERDES_COM_BGTC COM_OFF(0xA0) | |
| #define QSERDES_COM_DEC_START1 COM_OFF(0xAC) | |
| #define QSERDES_COM_PLL_AMP_OS COM_OFF(0xB0) | |
| #define QSERDES_COM_RES_CODE_UP_OFFSET COM_OFF(0xD8) | |
| #define QSERDES_COM_RES_CODE_DN_OFFSET COM_OFF(0xDC) | |
| #define QSERDES_COM_DIV_FRAC_START1 COM_OFF(0x100) | |
| #define QSERDES_COM_DIV_FRAC_START2 COM_OFF(0x104) | |
| #define QSERDES_COM_DIV_FRAC_START3 COM_OFF(0x108) | |
| #define QSERDES_COM_DEC_START2 COM_OFF(0x10C) | |
| #define QSERDES_COM_PLL_RXTXEPCLK_EN COM_OFF(0x110) | |
| #define QSERDES_COM_PLL_CRCTRL COM_OFF(0x114) | |
| #define QSERDES_COM_PLL_CLKEPDIV COM_OFF(0x118) | |
| /* TX LANE n (0, 1) registers */ | |
| #define QSERDES_TX_EMP_POST1_LVL(n) TX_OFF(n, 0x08) | |
| #define QSERDES_TX_DRV_LVL(n) TX_OFF(n, 0x0C) | |
| #define QSERDES_TX_LANE_MODE(n) TX_OFF(n, 0x54) | |
| /* RX LANE n (0, 1) registers */ | |
| #define QSERDES_RX_CDR_CONTROL1(n) RX_OFF(n, 0x0) | |
| #define QSERDES_RX_CDR_CONTROL_HALF(n) RX_OFF(n, 0x8) | |
| #define QSERDES_RX_RX_EQ_GAIN1_LSB(n) RX_OFF(n, 0xA8) | |
| #define QSERDES_RX_RX_EQ_GAIN1_MSB(n) RX_OFF(n, 0xAC) | |
| #define QSERDES_RX_RX_EQ_GAIN2_LSB(n) RX_OFF(n, 0xB0) | |
| #define QSERDES_RX_RX_EQ_GAIN2_MSB(n) RX_OFF(n, 0xB4) | |
| #define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(n) RX_OFF(n, 0xBC) | |
| #define QSERDES_RX_CDR_CONTROL_QUARTER(n) RX_OFF(n, 0xC) | |
| #define QSERDES_RX_SIGDET_CNTRL(n) RX_OFF(n, 0x100) | |
| /* UFS PHY registers */ | |
| #define UFS_PHY_PHY_START PHY_OFF(0x00) | |
| #define UFS_PHY_POWER_DOWN_CONTROL PHY_OFF(0x4) | |
| #define UFS_PHY_TX_LANE_ENABLE PHY_OFF(0x44) | |
| #define UFS_PHY_PWM_G1_CLK_DIVIDER PHY_OFF(0x08) | |
| #define UFS_PHY_PWM_G2_CLK_DIVIDER PHY_OFF(0x0C) | |
| #define UFS_PHY_PWM_G3_CLK_DIVIDER PHY_OFF(0x10) | |
| #define UFS_PHY_PWM_G4_CLK_DIVIDER PHY_OFF(0x14) | |
| #define UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER PHY_OFF(0x34) | |
| #define UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER PHY_OFF(0x38) | |
| #define UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER PHY_OFF(0x3C) | |
| #define UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER PHY_OFF(0x40) | |
| #define UFS_PHY_OMC_STATUS_RDVAL PHY_OFF(0x68) | |
| #define UFS_PHY_LINE_RESET_TIME PHY_OFF(0x28) | |
| #define UFS_PHY_LINE_RESET_GRANULARITY PHY_OFF(0x2C) | |
| #define UFS_PHY_TSYNC_RSYNC_CNTL PHY_OFF(0x48) | |
| #define UFS_PHY_PLL_CNTL PHY_OFF(0x50) | |
| #define UFS_PHY_TX_LARGE_AMP_DRV_LVL PHY_OFF(0x54) | |
| #define UFS_PHY_TX_SMALL_AMP_DRV_LVL PHY_OFF(0x5C) | |
| #define UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL PHY_OFF(0x58) | |
| #define UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL PHY_OFF(0x60) | |
| #define UFS_PHY_CFG_CHANGE_CNT_VAL PHY_OFF(0x64) | |
| #define UFS_PHY_RX_SYNC_WAIT_TIME PHY_OFF(0x6C) | |
| #define UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB4) | |
| #define UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE0) | |
| #define UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB8) | |
| #define UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE4) | |
| #define UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xBC) | |
| #define UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xE8) | |
| #define UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY PHY_OFF(0xFC) | |
| #define UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY PHY_OFF(0x100) | |
| #define UFS_PHY_RX_SIGDET_CTRL3 PHY_OFF(0x14c) | |
| #define UFS_PHY_RMMI_ATTR_CTRL PHY_OFF(0x160) | |
| #define UFS_PHY_RMMI_RX_CFGUPDT_L1 (1 << 7) | |
| #define UFS_PHY_RMMI_TX_CFGUPDT_L1 (1 << 6) | |
| #define UFS_PHY_RMMI_CFGWR_L1 (1 << 5) | |
| #define UFS_PHY_RMMI_CFGRD_L1 (1 << 4) | |
| #define UFS_PHY_RMMI_RX_CFGUPDT_L0 (1 << 3) | |
| #define UFS_PHY_RMMI_TX_CFGUPDT_L0 (1 << 2) | |
| #define UFS_PHY_RMMI_CFGWR_L0 (1 << 1) | |
| #define UFS_PHY_RMMI_CFGRD_L0 (1 << 0) | |
| #define UFS_PHY_RMMI_ATTRID PHY_OFF(0x164) | |
| #define UFS_PHY_RMMI_ATTRWRVAL PHY_OFF(0x168) | |
| #define UFS_PHY_RMMI_ATTRRDVAL_L0_STATUS PHY_OFF(0x16C) | |
| #define UFS_PHY_RMMI_ATTRRDVAL_L1_STATUS PHY_OFF(0x170) | |
| #define UFS_PHY_PCS_READY_STATUS PHY_OFF(0x174) | |
| #define UFS_PHY_TX_LANE_ENABLE_MASK 0x3 | |
| /* | |
| * This structure represents the 20nm specific phy. | |
| * common_cfg MUST remain the first field in this structure | |
| * in case extra fields are added. This way, when calling | |
| * get_ufs_qcom_phy() of generic phy, we can extract the | |
| * common phy structure (struct ufs_qcom_phy) out of it | |
| * regardless of the relevant specific phy. | |
| */ | |
| struct ufs_qcom_phy_qmp_20nm { | |
| struct ufs_qcom_phy common_cfg; | |
| }; | |
| static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_1_2_0[] = { | |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), | |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL3, 0x0D), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x3f), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x1b), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x0f), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(0), 0x2F), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(0), 0x20), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(1), 0x2F), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(1), 0x20), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x3), | |
| }; | |
| static struct ufs_qcom_phy_calibration phy_cal_table_rate_A_1_3_0[] = { | |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), | |
| UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SIGDET_CTRL3, 0x0D), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x2b), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x38), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x3c), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_CODE_UP_OFFSET, 0x02), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_CODE_DN_OFFSET, 0x02), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CNTRL, 0x40), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x3), | |
| }; | |
| static struct ufs_qcom_phy_calibration phy_cal_table_rate_B[] = { | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x98), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0x65), | |
| UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x1e), | |
| }; | |
| #endif |