| # | |
| # PINCTRL infrastructure and drivers | |
| # | |
| config PINCTRL | |
| bool | |
| menu "Pin controllers" | |
| depends on PINCTRL | |
| config PINMUX | |
| bool "Support pin multiplexing controllers" if COMPILE_TEST | |
| config PINCONF | |
| bool "Support pin configuration controllers" if COMPILE_TEST | |
| config GENERIC_PINCONF | |
| bool | |
| select PINCONF | |
| config DEBUG_PINCTRL | |
| bool "Debug PINCTRL calls" | |
| depends on DEBUG_KERNEL | |
| help | |
| Say Y here to add some extra checks and diagnostics to PINCTRL calls. | |
| config PINCTRL_ADI2 | |
| bool "ADI pin controller driver" | |
| depends on BLACKFIN | |
| select PINMUX | |
| select IRQ_DOMAIN | |
| help | |
| This is the pin controller and gpio driver for ADI BF54x, BF60x and | |
| future processors. This option is selected automatically when specific | |
| machine and arch are selected to build. | |
| config PINCTRL_AS3722 | |
| tristate "Pinctrl and GPIO driver for ams AS3722 PMIC" | |
| depends on MFD_AS3722 && GPIOLIB | |
| select PINMUX | |
| select GENERIC_PINCONF | |
| help | |
| AS3722 device supports the configuration of GPIO pins for different | |
| functionality. This driver supports the pinmux, push-pull and | |
| open drain configuration for the GPIO pins of AS3722 devices. It also | |
| supports the GPIO functionality through gpiolib. | |
| config PINCTRL_BF54x | |
| def_bool y if BF54x | |
| select PINCTRL_ADI2 | |
| config PINCTRL_BF60x | |
| def_bool y if BF60x | |
| select PINCTRL_ADI2 | |
| config PINCTRL_AT91 | |
| bool "AT91 pinctrl driver" | |
| depends on OF | |
| depends on ARCH_AT91 | |
| select PINMUX | |
| select PINCONF | |
| select GPIOLIB | |
| select OF_GPIO | |
| select GPIOLIB_IRQCHIP | |
| help | |
| Say Y here to enable the at91 pinctrl driver | |
| config PINCTRL_AT91PIO4 | |
| bool "AT91 PIO4 pinctrl driver" | |
| depends on OF | |
| depends on ARCH_AT91 | |
| select PINMUX | |
| select GENERIC_PINCONF | |
| select GPIOLIB | |
| select GPIOLIB_IRQCHIP | |
| select OF_GPIO | |
| help | |
| Say Y here to enable the at91 pinctrl/gpio driver for Atmel PIO4 | |
| controller available on sama5d2 SoC. | |
| config PINCTRL_AMD | |
| tristate "AMD GPIO pin control" | |
| depends on GPIOLIB | |
| select GPIOLIB_IRQCHIP | |
| select PINCONF | |
| select GENERIC_PINCONF | |
| help | |
| driver for memory mapped GPIO functionality on AMD platforms | |
| (x86 or arm).Most pins are usually muxed to some other | |
| functionality by firmware,so only a small amount is available | |
| for gpio use. | |
| Requires ACPI/FDT device enumeration code to set up a platform | |
| device. | |
| config PINCTRL_DIGICOLOR | |
| bool | |
| depends on OF && (ARCH_DIGICOLOR || COMPILE_TEST) | |
| select PINMUX | |
| select GENERIC_PINCONF | |
| config PINCTRL_LANTIQ | |
| bool | |
| depends on LANTIQ | |
| select PINMUX | |
| select PINCONF | |
| config PINCTRL_LPC18XX | |
| bool "NXP LPC18XX/43XX SCU pinctrl driver" | |
| depends on OF && (ARCH_LPC18XX || COMPILE_TEST) | |
| default ARCH_LPC18XX | |
| select PINMUX | |
| select GENERIC_PINCONF | |
| help | |
| Pinctrl driver for NXP LPC18xx/43xx System Control Unit (SCU). | |
| config PINCTRL_FALCON | |
| bool | |
| depends on SOC_FALCON | |
| depends on PINCTRL_LANTIQ | |
| config PINCTRL_MESON | |
| bool | |
| depends on OF | |
| select PINMUX | |
| select PINCONF | |
| select GENERIC_PINCONF | |
| select GPIOLIB | |
| select OF_GPIO | |
| select REGMAP_MMIO | |
| config PINCTRL_OXNAS | |
| bool | |
| depends on OF | |
| select PINMUX | |
| select PINCONF | |
| select GENERIC_PINCONF | |
| select GPIOLIB | |
| select OF_GPIO | |
| select GPIOLIB_IRQCHIP | |
| select MFD_SYSCON | |
| config PINCTRL_ROCKCHIP | |
| bool | |
| select PINMUX | |
| select GENERIC_PINCONF | |
| select GENERIC_IRQ_CHIP | |
| select MFD_SYSCON | |
| config PINCTRL_SINGLE | |
| tristate "One-register-per-pin type device tree based pinctrl driver" | |
| depends on OF | |
| select PINMUX | |
| select PINCONF | |
| select GENERIC_PINCONF | |
| help | |
| This selects the device tree based generic pinctrl driver. | |
| config PINCTRL_SIRF | |
| bool "CSR SiRFprimaII pin controller driver" | |
| depends on ARCH_SIRF | |
| select PINMUX | |
| select PINCONF | |
| select GENERIC_PINCONF | |
| select GPIOLIB_IRQCHIP | |
| config PINCTRL_PISTACHIO | |
| def_bool y if MACH_PISTACHIO | |
| depends on GPIOLIB | |
| select PINMUX | |
| select GENERIC_PINCONF | |
| select GPIOLIB_IRQCHIP | |
| select OF_GPIO | |
| config PINCTRL_ST | |
| bool | |
| depends on OF | |
| select PINMUX | |
| select PINCONF | |
| select GPIOLIB_IRQCHIP | |
| config PINCTRL_TZ1090 | |
| bool "Toumaz Xenif TZ1090 pin control driver" | |
| depends on SOC_TZ1090 | |
| select PINMUX | |
| select GENERIC_PINCONF | |
| config PINCTRL_TZ1090_PDC | |
| bool "Toumaz Xenif TZ1090 PDC pin control driver" | |
| depends on SOC_TZ1090 | |
| select PINMUX | |
| select PINCONF | |
| config PINCTRL_U300 | |
| bool "U300 pin controller driver" | |
| depends on ARCH_U300 | |
| select PINMUX | |
| select GENERIC_PINCONF | |
| config PINCTRL_COH901 | |
| bool "ST-Ericsson U300 COH 901 335/571 GPIO" | |
| depends on GPIOLIB && ARCH_U300 && PINCTRL_U300 | |
| select GPIOLIB_IRQCHIP | |
| help | |
| Say yes here to support GPIO interface on ST-Ericsson U300. | |
| The names of the two IP block variants supported are | |
| COH 901 335 and COH 901 571/3. They contain 3, 5 or 7 | |
| ports of 8 GPIO pins each. | |
| config PINCTRL_MAX77620 | |
| tristate "MAX77620/MAX20024 Pincontrol support" | |
| depends on MFD_MAX77620 | |
| select PINMUX | |
| select GENERIC_PINCONF | |
| help | |
| Say Yes here to enable Pin control support for Maxim PMIC MAX77620. | |
| This PMIC has 8 GPIO pins that work as GPIO as well as special | |
| function in alternate mode. This driver also configure push-pull, | |
| open drain, FPS slots etc. | |
| config PINCTRL_PALMAS | |
| tristate "Pinctrl driver for the PALMAS Series MFD devices" | |
| depends on OF && MFD_PALMAS | |
| select PINMUX | |
| select GENERIC_PINCONF | |
| help | |
| Palmas device supports the configuration of pins for different | |
| functionality. This driver supports the pinmux, push-pull and | |
| open drain configuration for the Palmas series devices like | |
| TPS65913, TPS80036 etc. | |
| config PINCTRL_PIC32 | |
| bool "Microchip PIC32 pin controller driver" | |
| depends on OF | |
| depends on MACH_PIC32 | |
| select PINMUX | |
| select GENERIC_PINCONF | |
| select GPIOLIB_IRQCHIP | |
| select OF_GPIO | |
| help | |
| This is the pin controller and gpio driver for Microchip PIC32 | |
| microcontrollers. This option is selected automatically when specific | |
| machine and arch are selected to build. | |
| config PINCTRL_PIC32MZDA | |
| def_bool y if PIC32MZDA | |
| select PINCTRL_PIC32 | |
| config PINCTRL_ZYNQ | |
| bool "Pinctrl driver for Xilinx Zynq" | |
| depends on ARCH_ZYNQ | |
| select PINMUX | |
| select GENERIC_PINCONF | |
| help | |
| This selects the pinctrl driver for Xilinx Zynq. | |
| source "drivers/pinctrl/aspeed/Kconfig" | |
| source "drivers/pinctrl/bcm/Kconfig" | |
| source "drivers/pinctrl/berlin/Kconfig" | |
| source "drivers/pinctrl/freescale/Kconfig" | |
| source "drivers/pinctrl/intel/Kconfig" | |
| source "drivers/pinctrl/mvebu/Kconfig" | |
| source "drivers/pinctrl/nomadik/Kconfig" | |
| source "drivers/pinctrl/pxa/Kconfig" | |
| source "drivers/pinctrl/qcom/Kconfig" | |
| source "drivers/pinctrl/samsung/Kconfig" | |
| source "drivers/pinctrl/sh-pfc/Kconfig" | |
| source "drivers/pinctrl/spear/Kconfig" | |
| source "drivers/pinctrl/stm32/Kconfig" | |
| source "drivers/pinctrl/sunxi/Kconfig" | |
| source "drivers/pinctrl/tegra/Kconfig" | |
| source "drivers/pinctrl/uniphier/Kconfig" | |
| source "drivers/pinctrl/vt8500/Kconfig" | |
| source "drivers/pinctrl/mediatek/Kconfig" | |
| config PINCTRL_XWAY | |
| bool | |
| depends on SOC_TYPE_XWAY | |
| depends on PINCTRL_LANTIQ | |
| config PINCTRL_TB10X | |
| bool | |
| depends on OF && ARC_PLAT_TB10X | |
| select GPIOLIB | |
| endmenu |