| /* | |
| * Pin controller and GPIO driver for Amlogic Meson SoCs | |
| * | |
| * Copyright (C) 2014 Beniamino Galvani <b.galvani@gmail.com> | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License | |
| * version 2 as published by the Free Software Foundation. | |
| * | |
| * You should have received a copy of the GNU General Public License | |
| * along with this program. If not, see <http://www.gnu.org/licenses/>. | |
| */ | |
| /* | |
| * The available pins are organized in banks (A,B,C,D,E,X,Y,Z,AO, | |
| * BOOT,CARD for meson6, X,Y,DV,H,Z,AO,BOOT,CARD for meson8 and | |
| * X,Y,DV,H,AO,BOOT,CARD,DIF for meson8b) and each bank has a | |
| * variable number of pins. | |
| * | |
| * The AO bank is special because it belongs to the Always-On power | |
| * domain which can't be powered off; the bank also uses a set of | |
| * registers different from the other banks. | |
| * | |
| * For each pin controller there are 4 different register ranges that | |
| * control the following properties of the pins: | |
| * 1) pin muxing | |
| * 2) pull enable/disable | |
| * 3) pull up/down | |
| * 4) GPIO direction, output value, input value | |
| * | |
| * In some cases the register ranges for pull enable and pull | |
| * direction are the same and thus there are only 3 register ranges. | |
| * | |
| * Every pinmux group can be enabled by a specific bit in the first | |
| * register range; when all groups for a given pin are disabled the | |
| * pin acts as a GPIO. | |
| * | |
| * For the pull and GPIO configuration every bank uses a contiguous | |
| * set of bits in the register sets described above; the same register | |
| * can be shared by more banks with different offsets. | |
| * | |
| * In addition to this there are some registers shared between all | |
| * banks that control the IRQ functionality. This feature is not | |
| * supported at the moment by the driver. | |
| */ | |
| #include <linux/device.h> | |
| #include <linux/gpio.h> | |
| #include <linux/init.h> | |
| #include <linux/io.h> | |
| #include <linux/of.h> | |
| #include <linux/of_address.h> | |
| #include <linux/pinctrl/pinconf-generic.h> | |
| #include <linux/pinctrl/pinconf.h> | |
| #include <linux/pinctrl/pinctrl.h> | |
| #include <linux/pinctrl/pinmux.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/regmap.h> | |
| #include <linux/seq_file.h> | |
| #include "../core.h" | |
| #include "../pinctrl-utils.h" | |
| #include "pinctrl-meson.h" | |
| /** | |
| * meson_get_bank() - find the bank containing a given pin | |
| * | |
| * @pc: the pinctrl instance | |
| * @pin: the pin number | |
| * @bank: the found bank | |
| * | |
| * Return: 0 on success, a negative value on error | |
| */ | |
| static int meson_get_bank(struct meson_pinctrl *pc, unsigned int pin, | |
| struct meson_bank **bank) | |
| { | |
| int i; | |
| for (i = 0; i < pc->data->num_banks; i++) { | |
| if (pin >= pc->data->banks[i].first && | |
| pin <= pc->data->banks[i].last) { | |
| *bank = &pc->data->banks[i]; | |
| return 0; | |
| } | |
| } | |
| return -EINVAL; | |
| } | |
| /** | |
| * meson_calc_reg_and_bit() - calculate register and bit for a pin | |
| * | |
| * @bank: the bank containing the pin | |
| * @pin: the pin number | |
| * @reg_type: the type of register needed (pull-enable, pull, etc...) | |
| * @reg: the computed register offset | |
| * @bit: the computed bit | |
| */ | |
| static void meson_calc_reg_and_bit(struct meson_bank *bank, unsigned int pin, | |
| enum meson_reg_type reg_type, | |
| unsigned int *reg, unsigned int *bit) | |
| { | |
| struct meson_reg_desc *desc = &bank->regs[reg_type]; | |
| *reg = desc->reg * 4; | |
| *bit = desc->bit + pin - bank->first; | |
| } | |
| static int meson_get_groups_count(struct pinctrl_dev *pcdev) | |
| { | |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); | |
| return pc->data->num_groups; | |
| } | |
| static const char *meson_get_group_name(struct pinctrl_dev *pcdev, | |
| unsigned selector) | |
| { | |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); | |
| return pc->data->groups[selector].name; | |
| } | |
| static int meson_get_group_pins(struct pinctrl_dev *pcdev, unsigned selector, | |
| const unsigned **pins, unsigned *num_pins) | |
| { | |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); | |
| *pins = pc->data->groups[selector].pins; | |
| *num_pins = pc->data->groups[selector].num_pins; | |
| return 0; | |
| } | |
| static void meson_pin_dbg_show(struct pinctrl_dev *pcdev, struct seq_file *s, | |
| unsigned offset) | |
| { | |
| seq_printf(s, " %s", dev_name(pcdev->dev)); | |
| } | |
| static const struct pinctrl_ops meson_pctrl_ops = { | |
| .get_groups_count = meson_get_groups_count, | |
| .get_group_name = meson_get_group_name, | |
| .get_group_pins = meson_get_group_pins, | |
| .dt_node_to_map = pinconf_generic_dt_node_to_map_all, | |
| .dt_free_map = pinctrl_utils_free_map, | |
| .pin_dbg_show = meson_pin_dbg_show, | |
| }; | |
| /** | |
| * meson_pmx_disable_other_groups() - disable other groups using a given pin | |
| * | |
| * @pc: meson pin controller device | |
| * @pin: number of the pin | |
| * @sel_group: index of the selected group, or -1 if none | |
| * | |
| * The function disables all pinmux groups using a pin except the | |
| * selected one. If @sel_group is -1 all groups are disabled, leaving | |
| * the pin in GPIO mode. | |
| */ | |
| static void meson_pmx_disable_other_groups(struct meson_pinctrl *pc, | |
| unsigned int pin, int sel_group) | |
| { | |
| struct meson_pmx_group *group; | |
| int i, j; | |
| for (i = 0; i < pc->data->num_groups; i++) { | |
| group = &pc->data->groups[i]; | |
| if (group->is_gpio || i == sel_group) | |
| continue; | |
| for (j = 0; j < group->num_pins; j++) { | |
| if (group->pins[j] == pin) { | |
| /* We have found a group using the pin */ | |
| regmap_update_bits(pc->reg_mux, | |
| group->reg * 4, | |
| BIT(group->bit), 0); | |
| } | |
| } | |
| } | |
| } | |
| static int meson_pmx_set_mux(struct pinctrl_dev *pcdev, unsigned func_num, | |
| unsigned group_num) | |
| { | |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); | |
| struct meson_pmx_func *func = &pc->data->funcs[func_num]; | |
| struct meson_pmx_group *group = &pc->data->groups[group_num]; | |
| int i, ret = 0; | |
| dev_dbg(pc->dev, "enable function %s, group %s\n", func->name, | |
| group->name); | |
| /* | |
| * Disable groups using the same pin. | |
| * The selected group is not disabled to avoid glitches. | |
| */ | |
| for (i = 0; i < group->num_pins; i++) | |
| meson_pmx_disable_other_groups(pc, group->pins[i], group_num); | |
| /* Function 0 (GPIO) doesn't need any additional setting */ | |
| if (func_num) | |
| ret = regmap_update_bits(pc->reg_mux, group->reg * 4, | |
| BIT(group->bit), BIT(group->bit)); | |
| return ret; | |
| } | |
| static int meson_pmx_request_gpio(struct pinctrl_dev *pcdev, | |
| struct pinctrl_gpio_range *range, | |
| unsigned offset) | |
| { | |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); | |
| meson_pmx_disable_other_groups(pc, range->pin_base + offset, -1); | |
| return 0; | |
| } | |
| static int meson_pmx_get_funcs_count(struct pinctrl_dev *pcdev) | |
| { | |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); | |
| return pc->data->num_funcs; | |
| } | |
| static const char *meson_pmx_get_func_name(struct pinctrl_dev *pcdev, | |
| unsigned selector) | |
| { | |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); | |
| return pc->data->funcs[selector].name; | |
| } | |
| static int meson_pmx_get_groups(struct pinctrl_dev *pcdev, unsigned selector, | |
| const char * const **groups, | |
| unsigned * const num_groups) | |
| { | |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); | |
| *groups = pc->data->funcs[selector].groups; | |
| *num_groups = pc->data->funcs[selector].num_groups; | |
| return 0; | |
| } | |
| static const struct pinmux_ops meson_pmx_ops = { | |
| .set_mux = meson_pmx_set_mux, | |
| .get_functions_count = meson_pmx_get_funcs_count, | |
| .get_function_name = meson_pmx_get_func_name, | |
| .get_function_groups = meson_pmx_get_groups, | |
| .gpio_request_enable = meson_pmx_request_gpio, | |
| }; | |
| static int meson_pinconf_set(struct pinctrl_dev *pcdev, unsigned int pin, | |
| unsigned long *configs, unsigned num_configs) | |
| { | |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); | |
| struct meson_bank *bank; | |
| enum pin_config_param param; | |
| unsigned int reg, bit; | |
| int i, ret; | |
| u16 arg; | |
| ret = meson_get_bank(pc, pin, &bank); | |
| if (ret) | |
| return ret; | |
| for (i = 0; i < num_configs; i++) { | |
| param = pinconf_to_config_param(configs[i]); | |
| arg = pinconf_to_config_argument(configs[i]); | |
| switch (param) { | |
| case PIN_CONFIG_BIAS_DISABLE: | |
| dev_dbg(pc->dev, "pin %u: disable bias\n", pin); | |
| meson_calc_reg_and_bit(bank, pin, REG_PULL, ®, &bit); | |
| ret = regmap_update_bits(pc->reg_pull, reg, | |
| BIT(bit), 0); | |
| if (ret) | |
| return ret; | |
| break; | |
| case PIN_CONFIG_BIAS_PULL_UP: | |
| dev_dbg(pc->dev, "pin %u: enable pull-up\n", pin); | |
| meson_calc_reg_and_bit(bank, pin, REG_PULLEN, | |
| ®, &bit); | |
| ret = regmap_update_bits(pc->reg_pullen, reg, | |
| BIT(bit), BIT(bit)); | |
| if (ret) | |
| return ret; | |
| meson_calc_reg_and_bit(bank, pin, REG_PULL, ®, &bit); | |
| ret = regmap_update_bits(pc->reg_pull, reg, | |
| BIT(bit), BIT(bit)); | |
| if (ret) | |
| return ret; | |
| break; | |
| case PIN_CONFIG_BIAS_PULL_DOWN: | |
| dev_dbg(pc->dev, "pin %u: enable pull-down\n", pin); | |
| meson_calc_reg_and_bit(bank, pin, REG_PULLEN, | |
| ®, &bit); | |
| ret = regmap_update_bits(pc->reg_pullen, reg, | |
| BIT(bit), BIT(bit)); | |
| if (ret) | |
| return ret; | |
| meson_calc_reg_and_bit(bank, pin, REG_PULL, ®, &bit); | |
| ret = regmap_update_bits(pc->reg_pull, reg, | |
| BIT(bit), 0); | |
| if (ret) | |
| return ret; | |
| break; | |
| default: | |
| return -ENOTSUPP; | |
| } | |
| } | |
| return 0; | |
| } | |
| static int meson_pinconf_get_pull(struct meson_pinctrl *pc, unsigned int pin) | |
| { | |
| struct meson_bank *bank; | |
| unsigned int reg, bit, val; | |
| int ret, conf; | |
| ret = meson_get_bank(pc, pin, &bank); | |
| if (ret) | |
| return ret; | |
| meson_calc_reg_and_bit(bank, pin, REG_PULLEN, ®, &bit); | |
| ret = regmap_read(pc->reg_pullen, reg, &val); | |
| if (ret) | |
| return ret; | |
| if (!(val & BIT(bit))) { | |
| conf = PIN_CONFIG_BIAS_DISABLE; | |
| } else { | |
| meson_calc_reg_and_bit(bank, pin, REG_PULL, ®, &bit); | |
| ret = regmap_read(pc->reg_pull, reg, &val); | |
| if (ret) | |
| return ret; | |
| if (val & BIT(bit)) | |
| conf = PIN_CONFIG_BIAS_PULL_UP; | |
| else | |
| conf = PIN_CONFIG_BIAS_PULL_DOWN; | |
| } | |
| return conf; | |
| } | |
| static int meson_pinconf_get(struct pinctrl_dev *pcdev, unsigned int pin, | |
| unsigned long *config) | |
| { | |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); | |
| enum pin_config_param param = pinconf_to_config_param(*config); | |
| u16 arg; | |
| switch (param) { | |
| case PIN_CONFIG_BIAS_DISABLE: | |
| case PIN_CONFIG_BIAS_PULL_DOWN: | |
| case PIN_CONFIG_BIAS_PULL_UP: | |
| if (meson_pinconf_get_pull(pc, pin) == param) | |
| arg = 1; | |
| else | |
| return -EINVAL; | |
| break; | |
| default: | |
| return -ENOTSUPP; | |
| } | |
| *config = pinconf_to_config_packed(param, arg); | |
| dev_dbg(pc->dev, "pinconf for pin %u is %lu\n", pin, *config); | |
| return 0; | |
| } | |
| static int meson_pinconf_group_set(struct pinctrl_dev *pcdev, | |
| unsigned int num_group, | |
| unsigned long *configs, unsigned num_configs) | |
| { | |
| struct meson_pinctrl *pc = pinctrl_dev_get_drvdata(pcdev); | |
| struct meson_pmx_group *group = &pc->data->groups[num_group]; | |
| int i; | |
| dev_dbg(pc->dev, "set pinconf for group %s\n", group->name); | |
| for (i = 0; i < group->num_pins; i++) { | |
| meson_pinconf_set(pcdev, group->pins[i], configs, | |
| num_configs); | |
| } | |
| return 0; | |
| } | |
| static int meson_pinconf_group_get(struct pinctrl_dev *pcdev, | |
| unsigned int group, unsigned long *config) | |
| { | |
| return -ENOSYS; | |
| } | |
| static const struct pinconf_ops meson_pinconf_ops = { | |
| .pin_config_get = meson_pinconf_get, | |
| .pin_config_set = meson_pinconf_set, | |
| .pin_config_group_get = meson_pinconf_group_get, | |
| .pin_config_group_set = meson_pinconf_group_set, | |
| .is_generic = true, | |
| }; | |
| static int meson_gpio_request(struct gpio_chip *chip, unsigned gpio) | |
| { | |
| return pinctrl_request_gpio(chip->base + gpio); | |
| } | |
| static void meson_gpio_free(struct gpio_chip *chip, unsigned gpio) | |
| { | |
| struct meson_pinctrl *pc = gpiochip_get_data(chip); | |
| pinctrl_free_gpio(pc->data->pin_base + gpio); | |
| } | |
| static int meson_gpio_direction_input(struct gpio_chip *chip, unsigned gpio) | |
| { | |
| struct meson_pinctrl *pc = gpiochip_get_data(chip); | |
| unsigned int reg, bit, pin; | |
| struct meson_bank *bank; | |
| int ret; | |
| pin = pc->data->pin_base + gpio; | |
| ret = meson_get_bank(pc, pin, &bank); | |
| if (ret) | |
| return ret; | |
| meson_calc_reg_and_bit(bank, pin, REG_DIR, ®, &bit); | |
| return regmap_update_bits(pc->reg_gpio, reg, BIT(bit), BIT(bit)); | |
| } | |
| static int meson_gpio_direction_output(struct gpio_chip *chip, unsigned gpio, | |
| int value) | |
| { | |
| struct meson_pinctrl *pc = gpiochip_get_data(chip); | |
| unsigned int reg, bit, pin; | |
| struct meson_bank *bank; | |
| int ret; | |
| pin = pc->data->pin_base + gpio; | |
| ret = meson_get_bank(pc, pin, &bank); | |
| if (ret) | |
| return ret; | |
| meson_calc_reg_and_bit(bank, pin, REG_DIR, ®, &bit); | |
| ret = regmap_update_bits(pc->reg_gpio, reg, BIT(bit), 0); | |
| if (ret) | |
| return ret; | |
| meson_calc_reg_and_bit(bank, pin, REG_OUT, ®, &bit); | |
| return regmap_update_bits(pc->reg_gpio, reg, BIT(bit), | |
| value ? BIT(bit) : 0); | |
| } | |
| static void meson_gpio_set(struct gpio_chip *chip, unsigned gpio, int value) | |
| { | |
| struct meson_pinctrl *pc = gpiochip_get_data(chip); | |
| unsigned int reg, bit, pin; | |
| struct meson_bank *bank; | |
| int ret; | |
| pin = pc->data->pin_base + gpio; | |
| ret = meson_get_bank(pc, pin, &bank); | |
| if (ret) | |
| return; | |
| meson_calc_reg_and_bit(bank, pin, REG_OUT, ®, &bit); | |
| regmap_update_bits(pc->reg_gpio, reg, BIT(bit), | |
| value ? BIT(bit) : 0); | |
| } | |
| static int meson_gpio_get(struct gpio_chip *chip, unsigned gpio) | |
| { | |
| struct meson_pinctrl *pc = gpiochip_get_data(chip); | |
| unsigned int reg, bit, val, pin; | |
| struct meson_bank *bank; | |
| int ret; | |
| pin = pc->data->pin_base + gpio; | |
| ret = meson_get_bank(pc, pin, &bank); | |
| if (ret) | |
| return ret; | |
| meson_calc_reg_and_bit(bank, pin, REG_IN, ®, &bit); | |
| regmap_read(pc->reg_gpio, reg, &val); | |
| return !!(val & BIT(bit)); | |
| } | |
| static const struct of_device_id meson_pinctrl_dt_match[] = { | |
| { | |
| .compatible = "amlogic,meson8-cbus-pinctrl", | |
| .data = &meson8_cbus_pinctrl_data, | |
| }, | |
| { | |
| .compatible = "amlogic,meson8b-cbus-pinctrl", | |
| .data = &meson8b_cbus_pinctrl_data, | |
| }, | |
| { | |
| .compatible = "amlogic,meson8-aobus-pinctrl", | |
| .data = &meson8_aobus_pinctrl_data, | |
| }, | |
| { | |
| .compatible = "amlogic,meson8b-aobus-pinctrl", | |
| .data = &meson8b_aobus_pinctrl_data, | |
| }, | |
| { | |
| .compatible = "amlogic,meson-gxbb-periphs-pinctrl", | |
| .data = &meson_gxbb_periphs_pinctrl_data, | |
| }, | |
| { | |
| .compatible = "amlogic,meson-gxbb-aobus-pinctrl", | |
| .data = &meson_gxbb_aobus_pinctrl_data, | |
| }, | |
| { }, | |
| }; | |
| static int meson_gpiolib_register(struct meson_pinctrl *pc) | |
| { | |
| int ret; | |
| pc->chip.label = pc->data->name; | |
| pc->chip.parent = pc->dev; | |
| pc->chip.request = meson_gpio_request; | |
| pc->chip.free = meson_gpio_free; | |
| pc->chip.direction_input = meson_gpio_direction_input; | |
| pc->chip.direction_output = meson_gpio_direction_output; | |
| pc->chip.get = meson_gpio_get; | |
| pc->chip.set = meson_gpio_set; | |
| pc->chip.base = pc->data->pin_base; | |
| pc->chip.ngpio = pc->data->num_pins; | |
| pc->chip.can_sleep = false; | |
| pc->chip.of_node = pc->of_node; | |
| pc->chip.of_gpio_n_cells = 2; | |
| ret = gpiochip_add_data(&pc->chip, pc); | |
| if (ret) { | |
| dev_err(pc->dev, "can't add gpio chip %s\n", | |
| pc->data->name); | |
| goto fail; | |
| } | |
| ret = gpiochip_add_pin_range(&pc->chip, dev_name(pc->dev), | |
| 0, pc->data->pin_base, | |
| pc->chip.ngpio); | |
| if (ret) { | |
| dev_err(pc->dev, "can't add pin range\n"); | |
| goto fail; | |
| } | |
| return 0; | |
| fail: | |
| gpiochip_remove(&pc->chip); | |
| return ret; | |
| } | |
| static struct regmap_config meson_regmap_config = { | |
| .reg_bits = 32, | |
| .val_bits = 32, | |
| .reg_stride = 4, | |
| }; | |
| static struct regmap *meson_map_resource(struct meson_pinctrl *pc, | |
| struct device_node *node, char *name) | |
| { | |
| struct resource res; | |
| void __iomem *base; | |
| int i; | |
| i = of_property_match_string(node, "reg-names", name); | |
| if (of_address_to_resource(node, i, &res)) | |
| return ERR_PTR(-ENOENT); | |
| base = devm_ioremap_resource(pc->dev, &res); | |
| if (IS_ERR(base)) | |
| return ERR_CAST(base); | |
| meson_regmap_config.max_register = resource_size(&res) - 4; | |
| meson_regmap_config.name = devm_kasprintf(pc->dev, GFP_KERNEL, | |
| "%s-%s", node->name, | |
| name); | |
| if (!meson_regmap_config.name) | |
| return ERR_PTR(-ENOMEM); | |
| return devm_regmap_init_mmio(pc->dev, base, &meson_regmap_config); | |
| } | |
| static int meson_pinctrl_parse_dt(struct meson_pinctrl *pc, | |
| struct device_node *node) | |
| { | |
| struct device_node *np, *gpio_np = NULL; | |
| for_each_child_of_node(node, np) { | |
| if (!of_find_property(np, "gpio-controller", NULL)) | |
| continue; | |
| if (gpio_np) { | |
| dev_err(pc->dev, "multiple gpio nodes\n"); | |
| return -EINVAL; | |
| } | |
| gpio_np = np; | |
| } | |
| if (!gpio_np) { | |
| dev_err(pc->dev, "no gpio node found\n"); | |
| return -EINVAL; | |
| } | |
| pc->of_node = gpio_np; | |
| pc->reg_mux = meson_map_resource(pc, gpio_np, "mux"); | |
| if (IS_ERR(pc->reg_mux)) { | |
| dev_err(pc->dev, "mux registers not found\n"); | |
| return PTR_ERR(pc->reg_mux); | |
| } | |
| pc->reg_pull = meson_map_resource(pc, gpio_np, "pull"); | |
| if (IS_ERR(pc->reg_pull)) { | |
| dev_err(pc->dev, "pull registers not found\n"); | |
| return PTR_ERR(pc->reg_pull); | |
| } | |
| pc->reg_pullen = meson_map_resource(pc, gpio_np, "pull-enable"); | |
| /* Use pull region if pull-enable one is not present */ | |
| if (IS_ERR(pc->reg_pullen)) | |
| pc->reg_pullen = pc->reg_pull; | |
| pc->reg_gpio = meson_map_resource(pc, gpio_np, "gpio"); | |
| if (IS_ERR(pc->reg_gpio)) { | |
| dev_err(pc->dev, "gpio registers not found\n"); | |
| return PTR_ERR(pc->reg_gpio); | |
| } | |
| return 0; | |
| } | |
| static int meson_pinctrl_probe(struct platform_device *pdev) | |
| { | |
| const struct of_device_id *match; | |
| struct device *dev = &pdev->dev; | |
| struct meson_pinctrl *pc; | |
| int ret; | |
| pc = devm_kzalloc(dev, sizeof(struct meson_pinctrl), GFP_KERNEL); | |
| if (!pc) | |
| return -ENOMEM; | |
| pc->dev = dev; | |
| match = of_match_node(meson_pinctrl_dt_match, pdev->dev.of_node); | |
| pc->data = (struct meson_pinctrl_data *) match->data; | |
| ret = meson_pinctrl_parse_dt(pc, pdev->dev.of_node); | |
| if (ret) | |
| return ret; | |
| pc->desc.name = "pinctrl-meson"; | |
| pc->desc.owner = THIS_MODULE; | |
| pc->desc.pctlops = &meson_pctrl_ops; | |
| pc->desc.pmxops = &meson_pmx_ops; | |
| pc->desc.confops = &meson_pinconf_ops; | |
| pc->desc.pins = pc->data->pins; | |
| pc->desc.npins = pc->data->num_pins; | |
| pc->pcdev = devm_pinctrl_register(pc->dev, &pc->desc, pc); | |
| if (IS_ERR(pc->pcdev)) { | |
| dev_err(pc->dev, "can't register pinctrl device"); | |
| return PTR_ERR(pc->pcdev); | |
| } | |
| return meson_gpiolib_register(pc); | |
| } | |
| static struct platform_driver meson_pinctrl_driver = { | |
| .probe = meson_pinctrl_probe, | |
| .driver = { | |
| .name = "meson-pinctrl", | |
| .of_match_table = meson_pinctrl_dt_match, | |
| }, | |
| }; | |
| builtin_platform_driver(meson_pinctrl_driver); |