| /* | |
| * Generic GPIO driver for logic cells found in the Nomadik SoC | |
| * | |
| * Copyright (C) 2008,2009 STMicroelectronics | |
| * Copyright (C) 2009 Alessandro Rubini <rubini@unipv.it> | |
| * Rewritten based on work by Prafulla WADASKAR <prafulla.wadaskar@st.com> | |
| * Copyright (C) 2011-2013 Linus Walleij <linus.walleij@linaro.org> | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License version 2 as | |
| * published by the Free Software Foundation. | |
| */ | |
| #include <linux/kernel.h> | |
| #include <linux/init.h> | |
| #include <linux/device.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/io.h> | |
| #include <linux/clk.h> | |
| #include <linux/err.h> | |
| #include <linux/gpio.h> | |
| #include <linux/spinlock.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/slab.h> | |
| #include <linux/of_device.h> | |
| #include <linux/of_address.h> | |
| #include <linux/bitops.h> | |
| #include <linux/pinctrl/machine.h> | |
| #include <linux/pinctrl/pinctrl.h> | |
| #include <linux/pinctrl/pinmux.h> | |
| #include <linux/pinctrl/pinconf.h> | |
| /* Since we request GPIOs from ourself */ | |
| #include <linux/pinctrl/consumer.h> | |
| #include "pinctrl-nomadik.h" | |
| #include "../core.h" | |
| #include "../pinctrl-utils.h" | |
| /* | |
| * The GPIO module in the Nomadik family of Systems-on-Chip is an | |
| * AMBA device, managing 32 pins and alternate functions. The logic block | |
| * is currently used in the Nomadik and ux500. | |
| * | |
| * Symbols in this file are called "nmk_gpio" for "nomadik gpio" | |
| */ | |
| /* | |
| * pin configurations are represented by 32-bit integers: | |
| * | |
| * bit 0.. 8 - Pin Number (512 Pins Maximum) | |
| * bit 9..10 - Alternate Function Selection | |
| * bit 11..12 - Pull up/down state | |
| * bit 13 - Sleep mode behaviour | |
| * bit 14 - Direction | |
| * bit 15 - Value (if output) | |
| * bit 16..18 - SLPM pull up/down state | |
| * bit 19..20 - SLPM direction | |
| * bit 21..22 - SLPM Value (if output) | |
| * bit 23..25 - PDIS value (if input) | |
| * bit 26 - Gpio mode | |
| * bit 27 - Sleep mode | |
| * | |
| * to facilitate the definition, the following macros are provided | |
| * | |
| * PIN_CFG_DEFAULT - default config (0): | |
| * pull up/down = disabled | |
| * sleep mode = input/wakeup | |
| * direction = input | |
| * value = low | |
| * SLPM direction = same as normal | |
| * SLPM pull = same as normal | |
| * SLPM value = same as normal | |
| * | |
| * PIN_CFG - default config with alternate function | |
| */ | |
| typedef unsigned long pin_cfg_t; | |
| #define PIN_NUM_MASK 0x1ff | |
| #define PIN_NUM(x) ((x) & PIN_NUM_MASK) | |
| #define PIN_ALT_SHIFT 9 | |
| #define PIN_ALT_MASK (0x3 << PIN_ALT_SHIFT) | |
| #define PIN_ALT(x) (((x) & PIN_ALT_MASK) >> PIN_ALT_SHIFT) | |
| #define PIN_GPIO (NMK_GPIO_ALT_GPIO << PIN_ALT_SHIFT) | |
| #define PIN_ALT_A (NMK_GPIO_ALT_A << PIN_ALT_SHIFT) | |
| #define PIN_ALT_B (NMK_GPIO_ALT_B << PIN_ALT_SHIFT) | |
| #define PIN_ALT_C (NMK_GPIO_ALT_C << PIN_ALT_SHIFT) | |
| #define PIN_PULL_SHIFT 11 | |
| #define PIN_PULL_MASK (0x3 << PIN_PULL_SHIFT) | |
| #define PIN_PULL(x) (((x) & PIN_PULL_MASK) >> PIN_PULL_SHIFT) | |
| #define PIN_PULL_NONE (NMK_GPIO_PULL_NONE << PIN_PULL_SHIFT) | |
| #define PIN_PULL_UP (NMK_GPIO_PULL_UP << PIN_PULL_SHIFT) | |
| #define PIN_PULL_DOWN (NMK_GPIO_PULL_DOWN << PIN_PULL_SHIFT) | |
| #define PIN_SLPM_SHIFT 13 | |
| #define PIN_SLPM_MASK (0x1 << PIN_SLPM_SHIFT) | |
| #define PIN_SLPM(x) (((x) & PIN_SLPM_MASK) >> PIN_SLPM_SHIFT) | |
| #define PIN_SLPM_MAKE_INPUT (NMK_GPIO_SLPM_INPUT << PIN_SLPM_SHIFT) | |
| #define PIN_SLPM_NOCHANGE (NMK_GPIO_SLPM_NOCHANGE << PIN_SLPM_SHIFT) | |
| /* These two replace the above in DB8500v2+ */ | |
| #define PIN_SLPM_WAKEUP_ENABLE (NMK_GPIO_SLPM_WAKEUP_ENABLE << PIN_SLPM_SHIFT) | |
| #define PIN_SLPM_WAKEUP_DISABLE (NMK_GPIO_SLPM_WAKEUP_DISABLE << PIN_SLPM_SHIFT) | |
| #define PIN_SLPM_USE_MUX_SETTINGS_IN_SLEEP PIN_SLPM_WAKEUP_DISABLE | |
| #define PIN_SLPM_GPIO PIN_SLPM_WAKEUP_ENABLE /* In SLPM, pin is a gpio */ | |
| #define PIN_SLPM_ALTFUNC PIN_SLPM_WAKEUP_DISABLE /* In SLPM, pin is altfunc */ | |
| #define PIN_DIR_SHIFT 14 | |
| #define PIN_DIR_MASK (0x1 << PIN_DIR_SHIFT) | |
| #define PIN_DIR(x) (((x) & PIN_DIR_MASK) >> PIN_DIR_SHIFT) | |
| #define PIN_DIR_INPUT (0 << PIN_DIR_SHIFT) | |
| #define PIN_DIR_OUTPUT (1 << PIN_DIR_SHIFT) | |
| #define PIN_VAL_SHIFT 15 | |
| #define PIN_VAL_MASK (0x1 << PIN_VAL_SHIFT) | |
| #define PIN_VAL(x) (((x) & PIN_VAL_MASK) >> PIN_VAL_SHIFT) | |
| #define PIN_VAL_LOW (0 << PIN_VAL_SHIFT) | |
| #define PIN_VAL_HIGH (1 << PIN_VAL_SHIFT) | |
| #define PIN_SLPM_PULL_SHIFT 16 | |
| #define PIN_SLPM_PULL_MASK (0x7 << PIN_SLPM_PULL_SHIFT) | |
| #define PIN_SLPM_PULL(x) \ | |
| (((x) & PIN_SLPM_PULL_MASK) >> PIN_SLPM_PULL_SHIFT) | |
| #define PIN_SLPM_PULL_NONE \ | |
| ((1 + NMK_GPIO_PULL_NONE) << PIN_SLPM_PULL_SHIFT) | |
| #define PIN_SLPM_PULL_UP \ | |
| ((1 + NMK_GPIO_PULL_UP) << PIN_SLPM_PULL_SHIFT) | |
| #define PIN_SLPM_PULL_DOWN \ | |
| ((1 + NMK_GPIO_PULL_DOWN) << PIN_SLPM_PULL_SHIFT) | |
| #define PIN_SLPM_DIR_SHIFT 19 | |
| #define PIN_SLPM_DIR_MASK (0x3 << PIN_SLPM_DIR_SHIFT) | |
| #define PIN_SLPM_DIR(x) \ | |
| (((x) & PIN_SLPM_DIR_MASK) >> PIN_SLPM_DIR_SHIFT) | |
| #define PIN_SLPM_DIR_INPUT ((1 + 0) << PIN_SLPM_DIR_SHIFT) | |
| #define PIN_SLPM_DIR_OUTPUT ((1 + 1) << PIN_SLPM_DIR_SHIFT) | |
| #define PIN_SLPM_VAL_SHIFT 21 | |
| #define PIN_SLPM_VAL_MASK (0x3 << PIN_SLPM_VAL_SHIFT) | |
| #define PIN_SLPM_VAL(x) \ | |
| (((x) & PIN_SLPM_VAL_MASK) >> PIN_SLPM_VAL_SHIFT) | |
| #define PIN_SLPM_VAL_LOW ((1 + 0) << PIN_SLPM_VAL_SHIFT) | |
| #define PIN_SLPM_VAL_HIGH ((1 + 1) << PIN_SLPM_VAL_SHIFT) | |
| #define PIN_SLPM_PDIS_SHIFT 23 | |
| #define PIN_SLPM_PDIS_MASK (0x3 << PIN_SLPM_PDIS_SHIFT) | |
| #define PIN_SLPM_PDIS(x) \ | |
| (((x) & PIN_SLPM_PDIS_MASK) >> PIN_SLPM_PDIS_SHIFT) | |
| #define PIN_SLPM_PDIS_NO_CHANGE (0 << PIN_SLPM_PDIS_SHIFT) | |
| #define PIN_SLPM_PDIS_DISABLED (1 << PIN_SLPM_PDIS_SHIFT) | |
| #define PIN_SLPM_PDIS_ENABLED (2 << PIN_SLPM_PDIS_SHIFT) | |
| #define PIN_LOWEMI_SHIFT 25 | |
| #define PIN_LOWEMI_MASK (0x1 << PIN_LOWEMI_SHIFT) | |
| #define PIN_LOWEMI(x) (((x) & PIN_LOWEMI_MASK) >> PIN_LOWEMI_SHIFT) | |
| #define PIN_LOWEMI_DISABLED (0 << PIN_LOWEMI_SHIFT) | |
| #define PIN_LOWEMI_ENABLED (1 << PIN_LOWEMI_SHIFT) | |
| #define PIN_GPIOMODE_SHIFT 26 | |
| #define PIN_GPIOMODE_MASK (0x1 << PIN_GPIOMODE_SHIFT) | |
| #define PIN_GPIOMODE(x) (((x) & PIN_GPIOMODE_MASK) >> PIN_GPIOMODE_SHIFT) | |
| #define PIN_GPIOMODE_DISABLED (0 << PIN_GPIOMODE_SHIFT) | |
| #define PIN_GPIOMODE_ENABLED (1 << PIN_GPIOMODE_SHIFT) | |
| #define PIN_SLEEPMODE_SHIFT 27 | |
| #define PIN_SLEEPMODE_MASK (0x1 << PIN_SLEEPMODE_SHIFT) | |
| #define PIN_SLEEPMODE(x) (((x) & PIN_SLEEPMODE_MASK) >> PIN_SLEEPMODE_SHIFT) | |
| #define PIN_SLEEPMODE_DISABLED (0 << PIN_SLEEPMODE_SHIFT) | |
| #define PIN_SLEEPMODE_ENABLED (1 << PIN_SLEEPMODE_SHIFT) | |
| /* Shortcuts. Use these instead of separate DIR, PULL, and VAL. */ | |
| #define PIN_INPUT_PULLDOWN (PIN_DIR_INPUT | PIN_PULL_DOWN) | |
| #define PIN_INPUT_PULLUP (PIN_DIR_INPUT | PIN_PULL_UP) | |
| #define PIN_INPUT_NOPULL (PIN_DIR_INPUT | PIN_PULL_NONE) | |
| #define PIN_OUTPUT_LOW (PIN_DIR_OUTPUT | PIN_VAL_LOW) | |
| #define PIN_OUTPUT_HIGH (PIN_DIR_OUTPUT | PIN_VAL_HIGH) | |
| #define PIN_SLPM_INPUT_PULLDOWN (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_DOWN) | |
| #define PIN_SLPM_INPUT_PULLUP (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_UP) | |
| #define PIN_SLPM_INPUT_NOPULL (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_NONE) | |
| #define PIN_SLPM_OUTPUT_LOW (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_LOW) | |
| #define PIN_SLPM_OUTPUT_HIGH (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_HIGH) | |
| #define PIN_CFG_DEFAULT (0) | |
| #define PIN_CFG(num, alt) \ | |
| (PIN_CFG_DEFAULT |\ | |
| (PIN_NUM(num) | PIN_##alt)) | |
| #define PIN_CFG_INPUT(num, alt, pull) \ | |
| (PIN_CFG_DEFAULT |\ | |
| (PIN_NUM(num) | PIN_##alt | PIN_INPUT_##pull)) | |
| #define PIN_CFG_OUTPUT(num, alt, val) \ | |
| (PIN_CFG_DEFAULT |\ | |
| (PIN_NUM(num) | PIN_##alt | PIN_OUTPUT_##val)) | |
| /* | |
| * "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving | |
| * the "gpio" namespace for generic and cross-machine functions | |
| */ | |
| #define GPIO_BLOCK_SHIFT 5 | |
| #define NMK_GPIO_PER_CHIP (1 << GPIO_BLOCK_SHIFT) | |
| #define NMK_MAX_BANKS DIV_ROUND_UP(ARCH_NR_GPIOS, NMK_GPIO_PER_CHIP) | |
| /* Register in the logic block */ | |
| #define NMK_GPIO_DAT 0x00 | |
| #define NMK_GPIO_DATS 0x04 | |
| #define NMK_GPIO_DATC 0x08 | |
| #define NMK_GPIO_PDIS 0x0c | |
| #define NMK_GPIO_DIR 0x10 | |
| #define NMK_GPIO_DIRS 0x14 | |
| #define NMK_GPIO_DIRC 0x18 | |
| #define NMK_GPIO_SLPC 0x1c | |
| #define NMK_GPIO_AFSLA 0x20 | |
| #define NMK_GPIO_AFSLB 0x24 | |
| #define NMK_GPIO_LOWEMI 0x28 | |
| #define NMK_GPIO_RIMSC 0x40 | |
| #define NMK_GPIO_FIMSC 0x44 | |
| #define NMK_GPIO_IS 0x48 | |
| #define NMK_GPIO_IC 0x4c | |
| #define NMK_GPIO_RWIMSC 0x50 | |
| #define NMK_GPIO_FWIMSC 0x54 | |
| #define NMK_GPIO_WKS 0x58 | |
| /* These appear in DB8540 and later ASICs */ | |
| #define NMK_GPIO_EDGELEVEL 0x5C | |
| #define NMK_GPIO_LEVEL 0x60 | |
| /* Pull up/down values */ | |
| enum nmk_gpio_pull { | |
| NMK_GPIO_PULL_NONE, | |
| NMK_GPIO_PULL_UP, | |
| NMK_GPIO_PULL_DOWN, | |
| }; | |
| /* Sleep mode */ | |
| enum nmk_gpio_slpm { | |
| NMK_GPIO_SLPM_INPUT, | |
| NMK_GPIO_SLPM_WAKEUP_ENABLE = NMK_GPIO_SLPM_INPUT, | |
| NMK_GPIO_SLPM_NOCHANGE, | |
| NMK_GPIO_SLPM_WAKEUP_DISABLE = NMK_GPIO_SLPM_NOCHANGE, | |
| }; | |
| struct nmk_gpio_chip { | |
| struct gpio_chip chip; | |
| struct irq_chip irqchip; | |
| void __iomem *addr; | |
| struct clk *clk; | |
| unsigned int bank; | |
| unsigned int parent_irq; | |
| int latent_parent_irq; | |
| u32 (*get_latent_status)(unsigned int bank); | |
| void (*set_ioforce)(bool enable); | |
| spinlock_t lock; | |
| bool sleepmode; | |
| /* Keep track of configured edges */ | |
| u32 edge_rising; | |
| u32 edge_falling; | |
| u32 real_wake; | |
| u32 rwimsc; | |
| u32 fwimsc; | |
| u32 rimsc; | |
| u32 fimsc; | |
| u32 pull_up; | |
| u32 lowemi; | |
| }; | |
| /** | |
| * struct nmk_pinctrl - state container for the Nomadik pin controller | |
| * @dev: containing device pointer | |
| * @pctl: corresponding pin controller device | |
| * @soc: SoC data for this specific chip | |
| * @prcm_base: PRCM register range virtual base | |
| */ | |
| struct nmk_pinctrl { | |
| struct device *dev; | |
| struct pinctrl_dev *pctl; | |
| const struct nmk_pinctrl_soc_data *soc; | |
| void __iomem *prcm_base; | |
| }; | |
| static struct nmk_gpio_chip *nmk_gpio_chips[NMK_MAX_BANKS]; | |
| static DEFINE_SPINLOCK(nmk_gpio_slpm_lock); | |
| #define NUM_BANKS ARRAY_SIZE(nmk_gpio_chips) | |
| static void __nmk_gpio_set_mode(struct nmk_gpio_chip *nmk_chip, | |
| unsigned offset, int gpio_mode) | |
| { | |
| u32 afunc, bfunc; | |
| afunc = readl(nmk_chip->addr + NMK_GPIO_AFSLA) & ~BIT(offset); | |
| bfunc = readl(nmk_chip->addr + NMK_GPIO_AFSLB) & ~BIT(offset); | |
| if (gpio_mode & NMK_GPIO_ALT_A) | |
| afunc |= BIT(offset); | |
| if (gpio_mode & NMK_GPIO_ALT_B) | |
| bfunc |= BIT(offset); | |
| writel(afunc, nmk_chip->addr + NMK_GPIO_AFSLA); | |
| writel(bfunc, nmk_chip->addr + NMK_GPIO_AFSLB); | |
| } | |
| static void __nmk_gpio_set_slpm(struct nmk_gpio_chip *nmk_chip, | |
| unsigned offset, enum nmk_gpio_slpm mode) | |
| { | |
| u32 slpm; | |
| slpm = readl(nmk_chip->addr + NMK_GPIO_SLPC); | |
| if (mode == NMK_GPIO_SLPM_NOCHANGE) | |
| slpm |= BIT(offset); | |
| else | |
| slpm &= ~BIT(offset); | |
| writel(slpm, nmk_chip->addr + NMK_GPIO_SLPC); | |
| } | |
| static void __nmk_gpio_set_pull(struct nmk_gpio_chip *nmk_chip, | |
| unsigned offset, enum nmk_gpio_pull pull) | |
| { | |
| u32 pdis; | |
| pdis = readl(nmk_chip->addr + NMK_GPIO_PDIS); | |
| if (pull == NMK_GPIO_PULL_NONE) { | |
| pdis |= BIT(offset); | |
| nmk_chip->pull_up &= ~BIT(offset); | |
| } else { | |
| pdis &= ~BIT(offset); | |
| } | |
| writel(pdis, nmk_chip->addr + NMK_GPIO_PDIS); | |
| if (pull == NMK_GPIO_PULL_UP) { | |
| nmk_chip->pull_up |= BIT(offset); | |
| writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DATS); | |
| } else if (pull == NMK_GPIO_PULL_DOWN) { | |
| nmk_chip->pull_up &= ~BIT(offset); | |
| writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DATC); | |
| } | |
| } | |
| static void __nmk_gpio_set_lowemi(struct nmk_gpio_chip *nmk_chip, | |
| unsigned offset, bool lowemi) | |
| { | |
| bool enabled = nmk_chip->lowemi & BIT(offset); | |
| if (lowemi == enabled) | |
| return; | |
| if (lowemi) | |
| nmk_chip->lowemi |= BIT(offset); | |
| else | |
| nmk_chip->lowemi &= ~BIT(offset); | |
| writel_relaxed(nmk_chip->lowemi, | |
| nmk_chip->addr + NMK_GPIO_LOWEMI); | |
| } | |
| static void __nmk_gpio_make_input(struct nmk_gpio_chip *nmk_chip, | |
| unsigned offset) | |
| { | |
| writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DIRC); | |
| } | |
| static void __nmk_gpio_set_output(struct nmk_gpio_chip *nmk_chip, | |
| unsigned offset, int val) | |
| { | |
| if (val) | |
| writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DATS); | |
| else | |
| writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DATC); | |
| } | |
| static void __nmk_gpio_make_output(struct nmk_gpio_chip *nmk_chip, | |
| unsigned offset, int val) | |
| { | |
| writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DIRS); | |
| __nmk_gpio_set_output(nmk_chip, offset, val); | |
| } | |
| static void __nmk_gpio_set_mode_safe(struct nmk_gpio_chip *nmk_chip, | |
| unsigned offset, int gpio_mode, | |
| bool glitch) | |
| { | |
| u32 rwimsc = nmk_chip->rwimsc; | |
| u32 fwimsc = nmk_chip->fwimsc; | |
| if (glitch && nmk_chip->set_ioforce) { | |
| u32 bit = BIT(offset); | |
| /* Prevent spurious wakeups */ | |
| writel(rwimsc & ~bit, nmk_chip->addr + NMK_GPIO_RWIMSC); | |
| writel(fwimsc & ~bit, nmk_chip->addr + NMK_GPIO_FWIMSC); | |
| nmk_chip->set_ioforce(true); | |
| } | |
| __nmk_gpio_set_mode(nmk_chip, offset, gpio_mode); | |
| if (glitch && nmk_chip->set_ioforce) { | |
| nmk_chip->set_ioforce(false); | |
| writel(rwimsc, nmk_chip->addr + NMK_GPIO_RWIMSC); | |
| writel(fwimsc, nmk_chip->addr + NMK_GPIO_FWIMSC); | |
| } | |
| } | |
| static void | |
| nmk_gpio_disable_lazy_irq(struct nmk_gpio_chip *nmk_chip, unsigned offset) | |
| { | |
| u32 falling = nmk_chip->fimsc & BIT(offset); | |
| u32 rising = nmk_chip->rimsc & BIT(offset); | |
| int gpio = nmk_chip->chip.base + offset; | |
| int irq = irq_find_mapping(nmk_chip->chip.irqdomain, offset); | |
| struct irq_data *d = irq_get_irq_data(irq); | |
| if (!rising && !falling) | |
| return; | |
| if (!d || !irqd_irq_disabled(d)) | |
| return; | |
| if (rising) { | |
| nmk_chip->rimsc &= ~BIT(offset); | |
| writel_relaxed(nmk_chip->rimsc, | |
| nmk_chip->addr + NMK_GPIO_RIMSC); | |
| } | |
| if (falling) { | |
| nmk_chip->fimsc &= ~BIT(offset); | |
| writel_relaxed(nmk_chip->fimsc, | |
| nmk_chip->addr + NMK_GPIO_FIMSC); | |
| } | |
| dev_dbg(nmk_chip->chip.parent, "%d: clearing interrupt mask\n", gpio); | |
| } | |
| static void nmk_write_masked(void __iomem *reg, u32 mask, u32 value) | |
| { | |
| u32 val; | |
| val = readl(reg); | |
| val = ((val & ~mask) | (value & mask)); | |
| writel(val, reg); | |
| } | |
| static void nmk_prcm_altcx_set_mode(struct nmk_pinctrl *npct, | |
| unsigned offset, unsigned alt_num) | |
| { | |
| int i; | |
| u16 reg; | |
| u8 bit; | |
| u8 alt_index; | |
| const struct prcm_gpiocr_altcx_pin_desc *pin_desc; | |
| const u16 *gpiocr_regs; | |
| if (!npct->prcm_base) | |
| return; | |
| if (alt_num > PRCM_IDX_GPIOCR_ALTC_MAX) { | |
| dev_err(npct->dev, "PRCM GPIOCR: alternate-C%i is invalid\n", | |
| alt_num); | |
| return; | |
| } | |
| for (i = 0 ; i < npct->soc->npins_altcx ; i++) { | |
| if (npct->soc->altcx_pins[i].pin == offset) | |
| break; | |
| } | |
| if (i == npct->soc->npins_altcx) { | |
| dev_dbg(npct->dev, "PRCM GPIOCR: pin %i is not found\n", | |
| offset); | |
| return; | |
| } | |
| pin_desc = npct->soc->altcx_pins + i; | |
| gpiocr_regs = npct->soc->prcm_gpiocr_registers; | |
| /* | |
| * If alt_num is NULL, just clear current ALTCx selection | |
| * to make sure we come back to a pure ALTC selection | |
| */ | |
| if (!alt_num) { | |
| for (i = 0 ; i < PRCM_IDX_GPIOCR_ALTC_MAX ; i++) { | |
| if (pin_desc->altcx[i].used == true) { | |
| reg = gpiocr_regs[pin_desc->altcx[i].reg_index]; | |
| bit = pin_desc->altcx[i].control_bit; | |
| if (readl(npct->prcm_base + reg) & BIT(bit)) { | |
| nmk_write_masked(npct->prcm_base + reg, BIT(bit), 0); | |
| dev_dbg(npct->dev, | |
| "PRCM GPIOCR: pin %i: alternate-C%i has been disabled\n", | |
| offset, i+1); | |
| } | |
| } | |
| } | |
| return; | |
| } | |
| alt_index = alt_num - 1; | |
| if (pin_desc->altcx[alt_index].used == false) { | |
| dev_warn(npct->dev, | |
| "PRCM GPIOCR: pin %i: alternate-C%i does not exist\n", | |
| offset, alt_num); | |
| return; | |
| } | |
| /* | |
| * Check if any other ALTCx functions are activated on this pin | |
| * and disable it first. | |
| */ | |
| for (i = 0 ; i < PRCM_IDX_GPIOCR_ALTC_MAX ; i++) { | |
| if (i == alt_index) | |
| continue; | |
| if (pin_desc->altcx[i].used == true) { | |
| reg = gpiocr_regs[pin_desc->altcx[i].reg_index]; | |
| bit = pin_desc->altcx[i].control_bit; | |
| if (readl(npct->prcm_base + reg) & BIT(bit)) { | |
| nmk_write_masked(npct->prcm_base + reg, BIT(bit), 0); | |
| dev_dbg(npct->dev, | |
| "PRCM GPIOCR: pin %i: alternate-C%i has been disabled\n", | |
| offset, i+1); | |
| } | |
| } | |
| } | |
| reg = gpiocr_regs[pin_desc->altcx[alt_index].reg_index]; | |
| bit = pin_desc->altcx[alt_index].control_bit; | |
| dev_dbg(npct->dev, "PRCM GPIOCR: pin %i: alternate-C%i has been selected\n", | |
| offset, alt_index+1); | |
| nmk_write_masked(npct->prcm_base + reg, BIT(bit), BIT(bit)); | |
| } | |
| /* | |
| * Safe sequence used to switch IOs between GPIO and Alternate-C mode: | |
| * - Save SLPM registers | |
| * - Set SLPM=0 for the IOs you want to switch and others to 1 | |
| * - Configure the GPIO registers for the IOs that are being switched | |
| * - Set IOFORCE=1 | |
| * - Modify the AFLSA/B registers for the IOs that are being switched | |
| * - Set IOFORCE=0 | |
| * - Restore SLPM registers | |
| * - Any spurious wake up event during switch sequence to be ignored and | |
| * cleared | |
| */ | |
| static void nmk_gpio_glitch_slpm_init(unsigned int *slpm) | |
| { | |
| int i; | |
| for (i = 0; i < NUM_BANKS; i++) { | |
| struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; | |
| unsigned int temp = slpm[i]; | |
| if (!chip) | |
| break; | |
| clk_enable(chip->clk); | |
| slpm[i] = readl(chip->addr + NMK_GPIO_SLPC); | |
| writel(temp, chip->addr + NMK_GPIO_SLPC); | |
| } | |
| } | |
| static void nmk_gpio_glitch_slpm_restore(unsigned int *slpm) | |
| { | |
| int i; | |
| for (i = 0; i < NUM_BANKS; i++) { | |
| struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; | |
| if (!chip) | |
| break; | |
| writel(slpm[i], chip->addr + NMK_GPIO_SLPC); | |
| clk_disable(chip->clk); | |
| } | |
| } | |
| static int __maybe_unused nmk_prcm_gpiocr_get_mode(struct pinctrl_dev *pctldev, int gpio) | |
| { | |
| int i; | |
| u16 reg; | |
| u8 bit; | |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); | |
| const struct prcm_gpiocr_altcx_pin_desc *pin_desc; | |
| const u16 *gpiocr_regs; | |
| if (!npct->prcm_base) | |
| return NMK_GPIO_ALT_C; | |
| for (i = 0; i < npct->soc->npins_altcx; i++) { | |
| if (npct->soc->altcx_pins[i].pin == gpio) | |
| break; | |
| } | |
| if (i == npct->soc->npins_altcx) | |
| return NMK_GPIO_ALT_C; | |
| pin_desc = npct->soc->altcx_pins + i; | |
| gpiocr_regs = npct->soc->prcm_gpiocr_registers; | |
| for (i = 0; i < PRCM_IDX_GPIOCR_ALTC_MAX; i++) { | |
| if (pin_desc->altcx[i].used == true) { | |
| reg = gpiocr_regs[pin_desc->altcx[i].reg_index]; | |
| bit = pin_desc->altcx[i].control_bit; | |
| if (readl(npct->prcm_base + reg) & BIT(bit)) | |
| return NMK_GPIO_ALT_C+i+1; | |
| } | |
| } | |
| return NMK_GPIO_ALT_C; | |
| } | |
| /* IRQ functions */ | |
| static void nmk_gpio_irq_ack(struct irq_data *d) | |
| { | |
| struct gpio_chip *chip = irq_data_get_irq_chip_data(d); | |
| struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); | |
| clk_enable(nmk_chip->clk); | |
| writel(BIT(d->hwirq), nmk_chip->addr + NMK_GPIO_IC); | |
| clk_disable(nmk_chip->clk); | |
| } | |
| enum nmk_gpio_irq_type { | |
| NORMAL, | |
| WAKE, | |
| }; | |
| static void __nmk_gpio_irq_modify(struct nmk_gpio_chip *nmk_chip, | |
| int offset, enum nmk_gpio_irq_type which, | |
| bool enable) | |
| { | |
| u32 *rimscval; | |
| u32 *fimscval; | |
| u32 rimscreg; | |
| u32 fimscreg; | |
| if (which == NORMAL) { | |
| rimscreg = NMK_GPIO_RIMSC; | |
| fimscreg = NMK_GPIO_FIMSC; | |
| rimscval = &nmk_chip->rimsc; | |
| fimscval = &nmk_chip->fimsc; | |
| } else { | |
| rimscreg = NMK_GPIO_RWIMSC; | |
| fimscreg = NMK_GPIO_FWIMSC; | |
| rimscval = &nmk_chip->rwimsc; | |
| fimscval = &nmk_chip->fwimsc; | |
| } | |
| /* we must individually set/clear the two edges */ | |
| if (nmk_chip->edge_rising & BIT(offset)) { | |
| if (enable) | |
| *rimscval |= BIT(offset); | |
| else | |
| *rimscval &= ~BIT(offset); | |
| writel(*rimscval, nmk_chip->addr + rimscreg); | |
| } | |
| if (nmk_chip->edge_falling & BIT(offset)) { | |
| if (enable) | |
| *fimscval |= BIT(offset); | |
| else | |
| *fimscval &= ~BIT(offset); | |
| writel(*fimscval, nmk_chip->addr + fimscreg); | |
| } | |
| } | |
| static void __nmk_gpio_set_wake(struct nmk_gpio_chip *nmk_chip, | |
| int offset, bool on) | |
| { | |
| /* | |
| * Ensure WAKEUP_ENABLE is on. No need to disable it if wakeup is | |
| * disabled, since setting SLPM to 1 increases power consumption, and | |
| * wakeup is anyhow controlled by the RIMSC and FIMSC registers. | |
| */ | |
| if (nmk_chip->sleepmode && on) { | |
| __nmk_gpio_set_slpm(nmk_chip, offset, | |
| NMK_GPIO_SLPM_WAKEUP_ENABLE); | |
| } | |
| __nmk_gpio_irq_modify(nmk_chip, offset, WAKE, on); | |
| } | |
| static int nmk_gpio_irq_maskunmask(struct irq_data *d, bool enable) | |
| { | |
| struct nmk_gpio_chip *nmk_chip; | |
| unsigned long flags; | |
| nmk_chip = irq_data_get_irq_chip_data(d); | |
| if (!nmk_chip) | |
| return -EINVAL; | |
| clk_enable(nmk_chip->clk); | |
| spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); | |
| spin_lock(&nmk_chip->lock); | |
| __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, enable); | |
| if (!(nmk_chip->real_wake & BIT(d->hwirq))) | |
| __nmk_gpio_set_wake(nmk_chip, d->hwirq, enable); | |
| spin_unlock(&nmk_chip->lock); | |
| spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); | |
| clk_disable(nmk_chip->clk); | |
| return 0; | |
| } | |
| static void nmk_gpio_irq_mask(struct irq_data *d) | |
| { | |
| nmk_gpio_irq_maskunmask(d, false); | |
| } | |
| static void nmk_gpio_irq_unmask(struct irq_data *d) | |
| { | |
| nmk_gpio_irq_maskunmask(d, true); | |
| } | |
| static int nmk_gpio_irq_set_wake(struct irq_data *d, unsigned int on) | |
| { | |
| struct nmk_gpio_chip *nmk_chip; | |
| unsigned long flags; | |
| nmk_chip = irq_data_get_irq_chip_data(d); | |
| if (!nmk_chip) | |
| return -EINVAL; | |
| clk_enable(nmk_chip->clk); | |
| spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); | |
| spin_lock(&nmk_chip->lock); | |
| if (irqd_irq_disabled(d)) | |
| __nmk_gpio_set_wake(nmk_chip, d->hwirq, on); | |
| if (on) | |
| nmk_chip->real_wake |= BIT(d->hwirq); | |
| else | |
| nmk_chip->real_wake &= ~BIT(d->hwirq); | |
| spin_unlock(&nmk_chip->lock); | |
| spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); | |
| clk_disable(nmk_chip->clk); | |
| return 0; | |
| } | |
| static int nmk_gpio_irq_set_type(struct irq_data *d, unsigned int type) | |
| { | |
| bool enabled = !irqd_irq_disabled(d); | |
| bool wake = irqd_is_wakeup_set(d); | |
| struct nmk_gpio_chip *nmk_chip; | |
| unsigned long flags; | |
| nmk_chip = irq_data_get_irq_chip_data(d); | |
| if (!nmk_chip) | |
| return -EINVAL; | |
| if (type & IRQ_TYPE_LEVEL_HIGH) | |
| return -EINVAL; | |
| if (type & IRQ_TYPE_LEVEL_LOW) | |
| return -EINVAL; | |
| clk_enable(nmk_chip->clk); | |
| spin_lock_irqsave(&nmk_chip->lock, flags); | |
| if (enabled) | |
| __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, false); | |
| if (enabled || wake) | |
| __nmk_gpio_irq_modify(nmk_chip, d->hwirq, WAKE, false); | |
| nmk_chip->edge_rising &= ~BIT(d->hwirq); | |
| if (type & IRQ_TYPE_EDGE_RISING) | |
| nmk_chip->edge_rising |= BIT(d->hwirq); | |
| nmk_chip->edge_falling &= ~BIT(d->hwirq); | |
| if (type & IRQ_TYPE_EDGE_FALLING) | |
| nmk_chip->edge_falling |= BIT(d->hwirq); | |
| if (enabled) | |
| __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, true); | |
| if (enabled || wake) | |
| __nmk_gpio_irq_modify(nmk_chip, d->hwirq, WAKE, true); | |
| spin_unlock_irqrestore(&nmk_chip->lock, flags); | |
| clk_disable(nmk_chip->clk); | |
| return 0; | |
| } | |
| static unsigned int nmk_gpio_irq_startup(struct irq_data *d) | |
| { | |
| struct nmk_gpio_chip *nmk_chip = irq_data_get_irq_chip_data(d); | |
| clk_enable(nmk_chip->clk); | |
| nmk_gpio_irq_unmask(d); | |
| return 0; | |
| } | |
| static void nmk_gpio_irq_shutdown(struct irq_data *d) | |
| { | |
| struct nmk_gpio_chip *nmk_chip = irq_data_get_irq_chip_data(d); | |
| nmk_gpio_irq_mask(d); | |
| clk_disable(nmk_chip->clk); | |
| } | |
| static void __nmk_gpio_irq_handler(struct irq_desc *desc, u32 status) | |
| { | |
| struct irq_chip *host_chip = irq_desc_get_chip(desc); | |
| struct gpio_chip *chip = irq_desc_get_handler_data(desc); | |
| chained_irq_enter(host_chip, desc); | |
| while (status) { | |
| int bit = __ffs(status); | |
| generic_handle_irq(irq_find_mapping(chip->irqdomain, bit)); | |
| status &= ~BIT(bit); | |
| } | |
| chained_irq_exit(host_chip, desc); | |
| } | |
| static void nmk_gpio_irq_handler(struct irq_desc *desc) | |
| { | |
| struct gpio_chip *chip = irq_desc_get_handler_data(desc); | |
| struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); | |
| u32 status; | |
| clk_enable(nmk_chip->clk); | |
| status = readl(nmk_chip->addr + NMK_GPIO_IS); | |
| clk_disable(nmk_chip->clk); | |
| __nmk_gpio_irq_handler(desc, status); | |
| } | |
| static void nmk_gpio_latent_irq_handler(struct irq_desc *desc) | |
| { | |
| struct gpio_chip *chip = irq_desc_get_handler_data(desc); | |
| struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); | |
| u32 status = nmk_chip->get_latent_status(nmk_chip->bank); | |
| __nmk_gpio_irq_handler(desc, status); | |
| } | |
| /* I/O Functions */ | |
| static int nmk_gpio_get_dir(struct gpio_chip *chip, unsigned offset) | |
| { | |
| struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); | |
| int dir; | |
| clk_enable(nmk_chip->clk); | |
| dir = !(readl(nmk_chip->addr + NMK_GPIO_DIR) & BIT(offset)); | |
| clk_disable(nmk_chip->clk); | |
| return dir; | |
| } | |
| static int nmk_gpio_make_input(struct gpio_chip *chip, unsigned offset) | |
| { | |
| struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); | |
| clk_enable(nmk_chip->clk); | |
| writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DIRC); | |
| clk_disable(nmk_chip->clk); | |
| return 0; | |
| } | |
| static int nmk_gpio_get_input(struct gpio_chip *chip, unsigned offset) | |
| { | |
| struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); | |
| int value; | |
| clk_enable(nmk_chip->clk); | |
| value = !!(readl(nmk_chip->addr + NMK_GPIO_DAT) & BIT(offset)); | |
| clk_disable(nmk_chip->clk); | |
| return value; | |
| } | |
| static void nmk_gpio_set_output(struct gpio_chip *chip, unsigned offset, | |
| int val) | |
| { | |
| struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); | |
| clk_enable(nmk_chip->clk); | |
| __nmk_gpio_set_output(nmk_chip, offset, val); | |
| clk_disable(nmk_chip->clk); | |
| } | |
| static int nmk_gpio_make_output(struct gpio_chip *chip, unsigned offset, | |
| int val) | |
| { | |
| struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); | |
| clk_enable(nmk_chip->clk); | |
| __nmk_gpio_make_output(nmk_chip, offset, val); | |
| clk_disable(nmk_chip->clk); | |
| return 0; | |
| } | |
| #ifdef CONFIG_DEBUG_FS | |
| static int nmk_gpio_get_mode(struct nmk_gpio_chip *nmk_chip, int offset) | |
| { | |
| u32 afunc, bfunc; | |
| clk_enable(nmk_chip->clk); | |
| afunc = readl(nmk_chip->addr + NMK_GPIO_AFSLA) & BIT(offset); | |
| bfunc = readl(nmk_chip->addr + NMK_GPIO_AFSLB) & BIT(offset); | |
| clk_disable(nmk_chip->clk); | |
| return (afunc ? NMK_GPIO_ALT_A : 0) | (bfunc ? NMK_GPIO_ALT_B : 0); | |
| } | |
| #include <linux/seq_file.h> | |
| static void nmk_gpio_dbg_show_one(struct seq_file *s, | |
| struct pinctrl_dev *pctldev, struct gpio_chip *chip, | |
| unsigned offset, unsigned gpio) | |
| { | |
| const char *label = gpiochip_is_requested(chip, offset); | |
| struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); | |
| int mode; | |
| bool is_out; | |
| bool data_out; | |
| bool pull; | |
| const char *modes[] = { | |
| [NMK_GPIO_ALT_GPIO] = "gpio", | |
| [NMK_GPIO_ALT_A] = "altA", | |
| [NMK_GPIO_ALT_B] = "altB", | |
| [NMK_GPIO_ALT_C] = "altC", | |
| [NMK_GPIO_ALT_C+1] = "altC1", | |
| [NMK_GPIO_ALT_C+2] = "altC2", | |
| [NMK_GPIO_ALT_C+3] = "altC3", | |
| [NMK_GPIO_ALT_C+4] = "altC4", | |
| }; | |
| const char *pulls[] = { | |
| "none ", | |
| "pull down", | |
| "pull up ", | |
| }; | |
| clk_enable(nmk_chip->clk); | |
| is_out = !!(readl(nmk_chip->addr + NMK_GPIO_DIR) & BIT(offset)); | |
| pull = !(readl(nmk_chip->addr + NMK_GPIO_PDIS) & BIT(offset)); | |
| data_out = !!(readl(nmk_chip->addr + NMK_GPIO_DAT) & BIT(offset)); | |
| mode = nmk_gpio_get_mode(nmk_chip, offset); | |
| if ((mode == NMK_GPIO_ALT_C) && pctldev) | |
| mode = nmk_prcm_gpiocr_get_mode(pctldev, gpio); | |
| if (is_out) { | |
| seq_printf(s, " gpio-%-3d (%-20.20s) out %s %s", | |
| gpio, | |
| label ?: "(none)", | |
| data_out ? "hi" : "lo", | |
| (mode < 0) ? "unknown" : modes[mode]); | |
| } else { | |
| int irq = gpio_to_irq(gpio); | |
| struct irq_desc *desc = irq_to_desc(irq); | |
| int pullidx = 0; | |
| int val; | |
| if (pull) | |
| pullidx = data_out ? 2 : 1; | |
| seq_printf(s, " gpio-%-3d (%-20.20s) in %s %s", | |
| gpio, | |
| label ?: "(none)", | |
| pulls[pullidx], | |
| (mode < 0) ? "unknown" : modes[mode]); | |
| val = nmk_gpio_get_input(chip, offset); | |
| seq_printf(s, " VAL %d", val); | |
| /* | |
| * This races with request_irq(), set_irq_type(), | |
| * and set_irq_wake() ... but those are "rare". | |
| */ | |
| if (irq > 0 && desc && desc->action) { | |
| char *trigger; | |
| if (nmk_chip->edge_rising & BIT(offset)) | |
| trigger = "edge-rising"; | |
| else if (nmk_chip->edge_falling & BIT(offset)) | |
| trigger = "edge-falling"; | |
| else | |
| trigger = "edge-undefined"; | |
| seq_printf(s, " irq-%d %s%s", | |
| irq, trigger, | |
| irqd_is_wakeup_set(&desc->irq_data) | |
| ? " wakeup" : ""); | |
| } | |
| } | |
| clk_disable(nmk_chip->clk); | |
| } | |
| static void nmk_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip) | |
| { | |
| unsigned i; | |
| unsigned gpio = chip->base; | |
| for (i = 0; i < chip->ngpio; i++, gpio++) { | |
| nmk_gpio_dbg_show_one(s, NULL, chip, i, gpio); | |
| seq_printf(s, "\n"); | |
| } | |
| } | |
| #else | |
| static inline void nmk_gpio_dbg_show_one(struct seq_file *s, | |
| struct pinctrl_dev *pctldev, | |
| struct gpio_chip *chip, | |
| unsigned offset, unsigned gpio) | |
| { | |
| } | |
| #define nmk_gpio_dbg_show NULL | |
| #endif | |
| /* | |
| * We will allocate memory for the state container using devm* allocators | |
| * binding to the first device reaching this point, it doesn't matter if | |
| * it is the pin controller or GPIO driver. However we need to use the right | |
| * platform device when looking up resources so pay attention to pdev. | |
| */ | |
| static struct nmk_gpio_chip *nmk_gpio_populate_chip(struct device_node *np, | |
| struct platform_device *pdev) | |
| { | |
| struct nmk_gpio_chip *nmk_chip; | |
| struct platform_device *gpio_pdev; | |
| struct gpio_chip *chip; | |
| struct resource *res; | |
| struct clk *clk; | |
| void __iomem *base; | |
| u32 id; | |
| gpio_pdev = of_find_device_by_node(np); | |
| if (!gpio_pdev) { | |
| pr_err("populate \"%s\": device not found\n", np->name); | |
| return ERR_PTR(-ENODEV); | |
| } | |
| if (of_property_read_u32(np, "gpio-bank", &id)) { | |
| dev_err(&pdev->dev, "populate: gpio-bank property not found\n"); | |
| return ERR_PTR(-EINVAL); | |
| } | |
| /* Already populated? */ | |
| nmk_chip = nmk_gpio_chips[id]; | |
| if (nmk_chip) | |
| return nmk_chip; | |
| nmk_chip = devm_kzalloc(&pdev->dev, sizeof(*nmk_chip), GFP_KERNEL); | |
| if (!nmk_chip) | |
| return ERR_PTR(-ENOMEM); | |
| nmk_chip->bank = id; | |
| chip = &nmk_chip->chip; | |
| chip->base = id * NMK_GPIO_PER_CHIP; | |
| chip->ngpio = NMK_GPIO_PER_CHIP; | |
| chip->label = dev_name(&gpio_pdev->dev); | |
| chip->parent = &gpio_pdev->dev; | |
| res = platform_get_resource(gpio_pdev, IORESOURCE_MEM, 0); | |
| base = devm_ioremap_resource(&pdev->dev, res); | |
| if (IS_ERR(base)) | |
| return base; | |
| nmk_chip->addr = base; | |
| clk = clk_get(&gpio_pdev->dev, NULL); | |
| if (IS_ERR(clk)) | |
| return (void *) clk; | |
| clk_prepare(clk); | |
| nmk_chip->clk = clk; | |
| BUG_ON(nmk_chip->bank >= ARRAY_SIZE(nmk_gpio_chips)); | |
| nmk_gpio_chips[id] = nmk_chip; | |
| return nmk_chip; | |
| } | |
| static int nmk_gpio_probe(struct platform_device *dev) | |
| { | |
| struct device_node *np = dev->dev.of_node; | |
| struct nmk_gpio_chip *nmk_chip; | |
| struct gpio_chip *chip; | |
| struct irq_chip *irqchip; | |
| int latent_irq; | |
| bool supports_sleepmode; | |
| int irq; | |
| int ret; | |
| nmk_chip = nmk_gpio_populate_chip(np, dev); | |
| if (IS_ERR(nmk_chip)) { | |
| dev_err(&dev->dev, "could not populate nmk chip struct\n"); | |
| return PTR_ERR(nmk_chip); | |
| } | |
| supports_sleepmode = | |
| of_property_read_bool(np, "st,supports-sleepmode"); | |
| /* Correct platform device ID */ | |
| dev->id = nmk_chip->bank; | |
| irq = platform_get_irq(dev, 0); | |
| if (irq < 0) | |
| return irq; | |
| /* It's OK for this IRQ not to be present */ | |
| latent_irq = platform_get_irq(dev, 1); | |
| /* | |
| * The virt address in nmk_chip->addr is in the nomadik register space, | |
| * so we can simply convert the resource address, without remapping | |
| */ | |
| nmk_chip->parent_irq = irq; | |
| nmk_chip->latent_parent_irq = latent_irq; | |
| nmk_chip->sleepmode = supports_sleepmode; | |
| spin_lock_init(&nmk_chip->lock); | |
| chip = &nmk_chip->chip; | |
| chip->request = gpiochip_generic_request; | |
| chip->free = gpiochip_generic_free; | |
| chip->get_direction = nmk_gpio_get_dir; | |
| chip->direction_input = nmk_gpio_make_input; | |
| chip->get = nmk_gpio_get_input; | |
| chip->direction_output = nmk_gpio_make_output; | |
| chip->set = nmk_gpio_set_output; | |
| chip->dbg_show = nmk_gpio_dbg_show; | |
| chip->can_sleep = false; | |
| chip->owner = THIS_MODULE; | |
| irqchip = &nmk_chip->irqchip; | |
| irqchip->irq_ack = nmk_gpio_irq_ack; | |
| irqchip->irq_mask = nmk_gpio_irq_mask; | |
| irqchip->irq_unmask = nmk_gpio_irq_unmask; | |
| irqchip->irq_set_type = nmk_gpio_irq_set_type; | |
| irqchip->irq_set_wake = nmk_gpio_irq_set_wake; | |
| irqchip->irq_startup = nmk_gpio_irq_startup; | |
| irqchip->irq_shutdown = nmk_gpio_irq_shutdown; | |
| irqchip->flags = IRQCHIP_MASK_ON_SUSPEND; | |
| irqchip->name = kasprintf(GFP_KERNEL, "nmk%u-%u-%u", | |
| dev->id, | |
| chip->base, | |
| chip->base + chip->ngpio - 1); | |
| clk_enable(nmk_chip->clk); | |
| nmk_chip->lowemi = readl_relaxed(nmk_chip->addr + NMK_GPIO_LOWEMI); | |
| clk_disable(nmk_chip->clk); | |
| chip->of_node = np; | |
| ret = gpiochip_add_data(chip, nmk_chip); | |
| if (ret) | |
| return ret; | |
| platform_set_drvdata(dev, nmk_chip); | |
| /* | |
| * Let the generic code handle this edge IRQ, the the chained | |
| * handler will perform the actual work of handling the parent | |
| * interrupt. | |
| */ | |
| ret = gpiochip_irqchip_add(chip, | |
| irqchip, | |
| 0, | |
| handle_edge_irq, | |
| IRQ_TYPE_NONE); | |
| if (ret) { | |
| dev_err(&dev->dev, "could not add irqchip\n"); | |
| gpiochip_remove(&nmk_chip->chip); | |
| return -ENODEV; | |
| } | |
| /* Then register the chain on the parent IRQ */ | |
| gpiochip_set_chained_irqchip(chip, | |
| irqchip, | |
| nmk_chip->parent_irq, | |
| nmk_gpio_irq_handler); | |
| if (nmk_chip->latent_parent_irq > 0) | |
| gpiochip_set_chained_irqchip(chip, | |
| irqchip, | |
| nmk_chip->latent_parent_irq, | |
| nmk_gpio_latent_irq_handler); | |
| dev_info(&dev->dev, "at address %p\n", nmk_chip->addr); | |
| return 0; | |
| } | |
| static int nmk_get_groups_cnt(struct pinctrl_dev *pctldev) | |
| { | |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); | |
| return npct->soc->ngroups; | |
| } | |
| static const char *nmk_get_group_name(struct pinctrl_dev *pctldev, | |
| unsigned selector) | |
| { | |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); | |
| return npct->soc->groups[selector].name; | |
| } | |
| static int nmk_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector, | |
| const unsigned **pins, | |
| unsigned *num_pins) | |
| { | |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); | |
| *pins = npct->soc->groups[selector].pins; | |
| *num_pins = npct->soc->groups[selector].npins; | |
| return 0; | |
| } | |
| static struct nmk_gpio_chip *find_nmk_gpio_from_pin(unsigned pin) | |
| { | |
| int i; | |
| struct nmk_gpio_chip *nmk_gpio; | |
| for(i = 0; i < NMK_MAX_BANKS; i++) { | |
| nmk_gpio = nmk_gpio_chips[i]; | |
| if (!nmk_gpio) | |
| continue; | |
| if (pin >= nmk_gpio->chip.base && | |
| pin < nmk_gpio->chip.base + nmk_gpio->chip.ngpio) | |
| return nmk_gpio; | |
| } | |
| return NULL; | |
| } | |
| static struct gpio_chip *find_gc_from_pin(unsigned pin) | |
| { | |
| struct nmk_gpio_chip *nmk_gpio = find_nmk_gpio_from_pin(pin); | |
| if (nmk_gpio) | |
| return &nmk_gpio->chip; | |
| return NULL; | |
| } | |
| static void nmk_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s, | |
| unsigned offset) | |
| { | |
| struct gpio_chip *chip = find_gc_from_pin(offset); | |
| if (!chip) { | |
| seq_printf(s, "invalid pin offset"); | |
| return; | |
| } | |
| nmk_gpio_dbg_show_one(s, pctldev, chip, offset - chip->base, offset); | |
| } | |
| static int nmk_dt_add_map_mux(struct pinctrl_map **map, unsigned *reserved_maps, | |
| unsigned *num_maps, const char *group, | |
| const char *function) | |
| { | |
| if (*num_maps == *reserved_maps) | |
| return -ENOSPC; | |
| (*map)[*num_maps].type = PIN_MAP_TYPE_MUX_GROUP; | |
| (*map)[*num_maps].data.mux.group = group; | |
| (*map)[*num_maps].data.mux.function = function; | |
| (*num_maps)++; | |
| return 0; | |
| } | |
| static int nmk_dt_add_map_configs(struct pinctrl_map **map, | |
| unsigned *reserved_maps, | |
| unsigned *num_maps, const char *group, | |
| unsigned long *configs, unsigned num_configs) | |
| { | |
| unsigned long *dup_configs; | |
| if (*num_maps == *reserved_maps) | |
| return -ENOSPC; | |
| dup_configs = kmemdup(configs, num_configs * sizeof(*dup_configs), | |
| GFP_KERNEL); | |
| if (!dup_configs) | |
| return -ENOMEM; | |
| (*map)[*num_maps].type = PIN_MAP_TYPE_CONFIGS_PIN; | |
| (*map)[*num_maps].data.configs.group_or_pin = group; | |
| (*map)[*num_maps].data.configs.configs = dup_configs; | |
| (*map)[*num_maps].data.configs.num_configs = num_configs; | |
| (*num_maps)++; | |
| return 0; | |
| } | |
| #define NMK_CONFIG_PIN(x, y) { .property = x, .config = y, } | |
| #define NMK_CONFIG_PIN_ARRAY(x, y) { .property = x, .choice = y, \ | |
| .size = ARRAY_SIZE(y), } | |
| static const unsigned long nmk_pin_input_modes[] = { | |
| PIN_INPUT_NOPULL, | |
| PIN_INPUT_PULLUP, | |
| PIN_INPUT_PULLDOWN, | |
| }; | |
| static const unsigned long nmk_pin_output_modes[] = { | |
| PIN_OUTPUT_LOW, | |
| PIN_OUTPUT_HIGH, | |
| PIN_DIR_OUTPUT, | |
| }; | |
| static const unsigned long nmk_pin_sleep_modes[] = { | |
| PIN_SLEEPMODE_DISABLED, | |
| PIN_SLEEPMODE_ENABLED, | |
| }; | |
| static const unsigned long nmk_pin_sleep_input_modes[] = { | |
| PIN_SLPM_INPUT_NOPULL, | |
| PIN_SLPM_INPUT_PULLUP, | |
| PIN_SLPM_INPUT_PULLDOWN, | |
| PIN_SLPM_DIR_INPUT, | |
| }; | |
| static const unsigned long nmk_pin_sleep_output_modes[] = { | |
| PIN_SLPM_OUTPUT_LOW, | |
| PIN_SLPM_OUTPUT_HIGH, | |
| PIN_SLPM_DIR_OUTPUT, | |
| }; | |
| static const unsigned long nmk_pin_sleep_wakeup_modes[] = { | |
| PIN_SLPM_WAKEUP_DISABLE, | |
| PIN_SLPM_WAKEUP_ENABLE, | |
| }; | |
| static const unsigned long nmk_pin_gpio_modes[] = { | |
| PIN_GPIOMODE_DISABLED, | |
| PIN_GPIOMODE_ENABLED, | |
| }; | |
| static const unsigned long nmk_pin_sleep_pdis_modes[] = { | |
| PIN_SLPM_PDIS_DISABLED, | |
| PIN_SLPM_PDIS_ENABLED, | |
| }; | |
| struct nmk_cfg_param { | |
| const char *property; | |
| unsigned long config; | |
| const unsigned long *choice; | |
| int size; | |
| }; | |
| static const struct nmk_cfg_param nmk_cfg_params[] = { | |
| NMK_CONFIG_PIN_ARRAY("ste,input", nmk_pin_input_modes), | |
| NMK_CONFIG_PIN_ARRAY("ste,output", nmk_pin_output_modes), | |
| NMK_CONFIG_PIN_ARRAY("ste,sleep", nmk_pin_sleep_modes), | |
| NMK_CONFIG_PIN_ARRAY("ste,sleep-input", nmk_pin_sleep_input_modes), | |
| NMK_CONFIG_PIN_ARRAY("ste,sleep-output", nmk_pin_sleep_output_modes), | |
| NMK_CONFIG_PIN_ARRAY("ste,sleep-wakeup", nmk_pin_sleep_wakeup_modes), | |
| NMK_CONFIG_PIN_ARRAY("ste,gpio", nmk_pin_gpio_modes), | |
| NMK_CONFIG_PIN_ARRAY("ste,sleep-pull-disable", nmk_pin_sleep_pdis_modes), | |
| }; | |
| static int nmk_dt_pin_config(int index, int val, unsigned long *config) | |
| { | |
| int ret = 0; | |
| if (nmk_cfg_params[index].choice == NULL) | |
| *config = nmk_cfg_params[index].config; | |
| else { | |
| /* test if out of range */ | |
| if (val < nmk_cfg_params[index].size) { | |
| *config = nmk_cfg_params[index].config | | |
| nmk_cfg_params[index].choice[val]; | |
| } | |
| } | |
| return ret; | |
| } | |
| static const char *nmk_find_pin_name(struct pinctrl_dev *pctldev, const char *pin_name) | |
| { | |
| int i, pin_number; | |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); | |
| if (sscanf((char *)pin_name, "GPIO%d", &pin_number) == 1) | |
| for (i = 0; i < npct->soc->npins; i++) | |
| if (npct->soc->pins[i].number == pin_number) | |
| return npct->soc->pins[i].name; | |
| return NULL; | |
| } | |
| static bool nmk_pinctrl_dt_get_config(struct device_node *np, | |
| unsigned long *configs) | |
| { | |
| bool has_config = 0; | |
| unsigned long cfg = 0; | |
| int i, val, ret; | |
| for (i = 0; i < ARRAY_SIZE(nmk_cfg_params); i++) { | |
| ret = of_property_read_u32(np, | |
| nmk_cfg_params[i].property, &val); | |
| if (ret != -EINVAL) { | |
| if (nmk_dt_pin_config(i, val, &cfg) == 0) { | |
| *configs |= cfg; | |
| has_config = 1; | |
| } | |
| } | |
| } | |
| return has_config; | |
| } | |
| static int nmk_pinctrl_dt_subnode_to_map(struct pinctrl_dev *pctldev, | |
| struct device_node *np, | |
| struct pinctrl_map **map, | |
| unsigned *reserved_maps, | |
| unsigned *num_maps) | |
| { | |
| int ret; | |
| const char *function = NULL; | |
| unsigned long configs = 0; | |
| bool has_config = 0; | |
| struct property *prop; | |
| struct device_node *np_config; | |
| ret = of_property_read_string(np, "function", &function); | |
| if (ret >= 0) { | |
| const char *group; | |
| ret = of_property_count_strings(np, "groups"); | |
| if (ret < 0) | |
| goto exit; | |
| ret = pinctrl_utils_reserve_map(pctldev, map, | |
| reserved_maps, | |
| num_maps, ret); | |
| if (ret < 0) | |
| goto exit; | |
| of_property_for_each_string(np, "groups", prop, group) { | |
| ret = nmk_dt_add_map_mux(map, reserved_maps, num_maps, | |
| group, function); | |
| if (ret < 0) | |
| goto exit; | |
| } | |
| } | |
| has_config = nmk_pinctrl_dt_get_config(np, &configs); | |
| np_config = of_parse_phandle(np, "ste,config", 0); | |
| if (np_config) | |
| has_config |= nmk_pinctrl_dt_get_config(np_config, &configs); | |
| if (has_config) { | |
| const char *gpio_name; | |
| const char *pin; | |
| ret = of_property_count_strings(np, "pins"); | |
| if (ret < 0) | |
| goto exit; | |
| ret = pinctrl_utils_reserve_map(pctldev, map, | |
| reserved_maps, | |
| num_maps, ret); | |
| if (ret < 0) | |
| goto exit; | |
| of_property_for_each_string(np, "pins", prop, pin) { | |
| gpio_name = nmk_find_pin_name(pctldev, pin); | |
| ret = nmk_dt_add_map_configs(map, reserved_maps, | |
| num_maps, | |
| gpio_name, &configs, 1); | |
| if (ret < 0) | |
| goto exit; | |
| } | |
| } | |
| exit: | |
| return ret; | |
| } | |
| static int nmk_pinctrl_dt_node_to_map(struct pinctrl_dev *pctldev, | |
| struct device_node *np_config, | |
| struct pinctrl_map **map, unsigned *num_maps) | |
| { | |
| unsigned reserved_maps; | |
| struct device_node *np; | |
| int ret; | |
| reserved_maps = 0; | |
| *map = NULL; | |
| *num_maps = 0; | |
| for_each_child_of_node(np_config, np) { | |
| ret = nmk_pinctrl_dt_subnode_to_map(pctldev, np, map, | |
| &reserved_maps, num_maps); | |
| if (ret < 0) { | |
| pinctrl_utils_free_map(pctldev, *map, *num_maps); | |
| return ret; | |
| } | |
| } | |
| return 0; | |
| } | |
| static const struct pinctrl_ops nmk_pinctrl_ops = { | |
| .get_groups_count = nmk_get_groups_cnt, | |
| .get_group_name = nmk_get_group_name, | |
| .get_group_pins = nmk_get_group_pins, | |
| .pin_dbg_show = nmk_pin_dbg_show, | |
| .dt_node_to_map = nmk_pinctrl_dt_node_to_map, | |
| .dt_free_map = pinctrl_utils_free_map, | |
| }; | |
| static int nmk_pmx_get_funcs_cnt(struct pinctrl_dev *pctldev) | |
| { | |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); | |
| return npct->soc->nfunctions; | |
| } | |
| static const char *nmk_pmx_get_func_name(struct pinctrl_dev *pctldev, | |
| unsigned function) | |
| { | |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); | |
| return npct->soc->functions[function].name; | |
| } | |
| static int nmk_pmx_get_func_groups(struct pinctrl_dev *pctldev, | |
| unsigned function, | |
| const char * const **groups, | |
| unsigned * const num_groups) | |
| { | |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); | |
| *groups = npct->soc->functions[function].groups; | |
| *num_groups = npct->soc->functions[function].ngroups; | |
| return 0; | |
| } | |
| static int nmk_pmx_set(struct pinctrl_dev *pctldev, unsigned function, | |
| unsigned group) | |
| { | |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); | |
| const struct nmk_pingroup *g; | |
| static unsigned int slpm[NUM_BANKS]; | |
| unsigned long flags = 0; | |
| bool glitch; | |
| int ret = -EINVAL; | |
| int i; | |
| g = &npct->soc->groups[group]; | |
| if (g->altsetting < 0) | |
| return -EINVAL; | |
| dev_dbg(npct->dev, "enable group %s, %u pins\n", g->name, g->npins); | |
| /* | |
| * If we're setting altfunc C by setting both AFSLA and AFSLB to 1, | |
| * we may pass through an undesired state. In this case we take | |
| * some extra care. | |
| * | |
| * Safe sequence used to switch IOs between GPIO and Alternate-C mode: | |
| * - Save SLPM registers (since we have a shadow register in the | |
| * nmk_chip we're using that as backup) | |
| * - Set SLPM=0 for the IOs you want to switch and others to 1 | |
| * - Configure the GPIO registers for the IOs that are being switched | |
| * - Set IOFORCE=1 | |
| * - Modify the AFLSA/B registers for the IOs that are being switched | |
| * - Set IOFORCE=0 | |
| * - Restore SLPM registers | |
| * - Any spurious wake up event during switch sequence to be ignored | |
| * and cleared | |
| * | |
| * We REALLY need to save ALL slpm registers, because the external | |
| * IOFORCE will switch *all* ports to their sleepmode setting to as | |
| * to avoid glitches. (Not just one port!) | |
| */ | |
| glitch = ((g->altsetting & NMK_GPIO_ALT_C) == NMK_GPIO_ALT_C); | |
| if (glitch) { | |
| spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); | |
| /* Initially don't put any pins to sleep when switching */ | |
| memset(slpm, 0xff, sizeof(slpm)); | |
| /* | |
| * Then mask the pins that need to be sleeping now when we're | |
| * switching to the ALT C function. | |
| */ | |
| for (i = 0; i < g->npins; i++) | |
| slpm[g->pins[i] / NMK_GPIO_PER_CHIP] &= ~BIT(g->pins[i]); | |
| nmk_gpio_glitch_slpm_init(slpm); | |
| } | |
| for (i = 0; i < g->npins; i++) { | |
| struct nmk_gpio_chip *nmk_chip; | |
| unsigned bit; | |
| nmk_chip = find_nmk_gpio_from_pin(g->pins[i]); | |
| if (!nmk_chip) { | |
| dev_err(npct->dev, | |
| "invalid pin offset %d in group %s at index %d\n", | |
| g->pins[i], g->name, i); | |
| goto out_glitch; | |
| } | |
| dev_dbg(npct->dev, "setting pin %d to altsetting %d\n", g->pins[i], g->altsetting); | |
| clk_enable(nmk_chip->clk); | |
| bit = g->pins[i] % NMK_GPIO_PER_CHIP; | |
| /* | |
| * If the pin is switching to altfunc, and there was an | |
| * interrupt installed on it which has been lazy disabled, | |
| * actually mask the interrupt to prevent spurious interrupts | |
| * that would occur while the pin is under control of the | |
| * peripheral. Only SKE does this. | |
| */ | |
| nmk_gpio_disable_lazy_irq(nmk_chip, bit); | |
| __nmk_gpio_set_mode_safe(nmk_chip, bit, | |
| (g->altsetting & NMK_GPIO_ALT_C), glitch); | |
| clk_disable(nmk_chip->clk); | |
| /* | |
| * Call PRCM GPIOCR config function in case ALTC | |
| * has been selected: | |
| * - If selection is a ALTCx, some bits in PRCM GPIOCR registers | |
| * must be set. | |
| * - If selection is pure ALTC and previous selection was ALTCx, | |
| * then some bits in PRCM GPIOCR registers must be cleared. | |
| */ | |
| if ((g->altsetting & NMK_GPIO_ALT_C) == NMK_GPIO_ALT_C) | |
| nmk_prcm_altcx_set_mode(npct, g->pins[i], | |
| g->altsetting >> NMK_GPIO_ALT_CX_SHIFT); | |
| } | |
| /* When all pins are successfully reconfigured we get here */ | |
| ret = 0; | |
| out_glitch: | |
| if (glitch) { | |
| nmk_gpio_glitch_slpm_restore(slpm); | |
| spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); | |
| } | |
| return ret; | |
| } | |
| static int nmk_gpio_request_enable(struct pinctrl_dev *pctldev, | |
| struct pinctrl_gpio_range *range, | |
| unsigned offset) | |
| { | |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); | |
| struct nmk_gpio_chip *nmk_chip; | |
| struct gpio_chip *chip; | |
| unsigned bit; | |
| if (!range) { | |
| dev_err(npct->dev, "invalid range\n"); | |
| return -EINVAL; | |
| } | |
| if (!range->gc) { | |
| dev_err(npct->dev, "missing GPIO chip in range\n"); | |
| return -EINVAL; | |
| } | |
| chip = range->gc; | |
| nmk_chip = gpiochip_get_data(chip); | |
| dev_dbg(npct->dev, "enable pin %u as GPIO\n", offset); | |
| clk_enable(nmk_chip->clk); | |
| bit = offset % NMK_GPIO_PER_CHIP; | |
| /* There is no glitch when converting any pin to GPIO */ | |
| __nmk_gpio_set_mode(nmk_chip, bit, NMK_GPIO_ALT_GPIO); | |
| clk_disable(nmk_chip->clk); | |
| return 0; | |
| } | |
| static void nmk_gpio_disable_free(struct pinctrl_dev *pctldev, | |
| struct pinctrl_gpio_range *range, | |
| unsigned offset) | |
| { | |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); | |
| dev_dbg(npct->dev, "disable pin %u as GPIO\n", offset); | |
| /* Set the pin to some default state, GPIO is usually default */ | |
| } | |
| static const struct pinmux_ops nmk_pinmux_ops = { | |
| .get_functions_count = nmk_pmx_get_funcs_cnt, | |
| .get_function_name = nmk_pmx_get_func_name, | |
| .get_function_groups = nmk_pmx_get_func_groups, | |
| .set_mux = nmk_pmx_set, | |
| .gpio_request_enable = nmk_gpio_request_enable, | |
| .gpio_disable_free = nmk_gpio_disable_free, | |
| .strict = true, | |
| }; | |
| static int nmk_pin_config_get(struct pinctrl_dev *pctldev, unsigned pin, | |
| unsigned long *config) | |
| { | |
| /* Not implemented */ | |
| return -EINVAL; | |
| } | |
| static int nmk_pin_config_set(struct pinctrl_dev *pctldev, unsigned pin, | |
| unsigned long *configs, unsigned num_configs) | |
| { | |
| static const char *pullnames[] = { | |
| [NMK_GPIO_PULL_NONE] = "none", | |
| [NMK_GPIO_PULL_UP] = "up", | |
| [NMK_GPIO_PULL_DOWN] = "down", | |
| [3] /* illegal */ = "??" | |
| }; | |
| static const char *slpmnames[] = { | |
| [NMK_GPIO_SLPM_INPUT] = "input/wakeup", | |
| [NMK_GPIO_SLPM_NOCHANGE] = "no-change/no-wakeup", | |
| }; | |
| struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); | |
| struct nmk_gpio_chip *nmk_chip; | |
| unsigned bit; | |
| pin_cfg_t cfg; | |
| int pull, slpm, output, val, i; | |
| bool lowemi, gpiomode, sleep; | |
| nmk_chip = find_nmk_gpio_from_pin(pin); | |
| if (!nmk_chip) { | |
| dev_err(npct->dev, | |
| "invalid pin offset %d\n", pin); | |
| return -EINVAL; | |
| } | |
| for (i = 0; i < num_configs; i++) { | |
| /* | |
| * The pin config contains pin number and altfunction fields, | |
| * here we just ignore that part. It's being handled by the | |
| * framework and pinmux callback respectively. | |
| */ | |
| cfg = (pin_cfg_t) configs[i]; | |
| pull = PIN_PULL(cfg); | |
| slpm = PIN_SLPM(cfg); | |
| output = PIN_DIR(cfg); | |
| val = PIN_VAL(cfg); | |
| lowemi = PIN_LOWEMI(cfg); | |
| gpiomode = PIN_GPIOMODE(cfg); | |
| sleep = PIN_SLEEPMODE(cfg); | |
| if (sleep) { | |
| int slpm_pull = PIN_SLPM_PULL(cfg); | |
| int slpm_output = PIN_SLPM_DIR(cfg); | |
| int slpm_val = PIN_SLPM_VAL(cfg); | |
| /* All pins go into GPIO mode at sleep */ | |
| gpiomode = true; | |
| /* | |
| * The SLPM_* values are normal values + 1 to allow zero | |
| * to mean "same as normal". | |
| */ | |
| if (slpm_pull) | |
| pull = slpm_pull - 1; | |
| if (slpm_output) | |
| output = slpm_output - 1; | |
| if (slpm_val) | |
| val = slpm_val - 1; | |
| dev_dbg(nmk_chip->chip.parent, | |
| "pin %d: sleep pull %s, dir %s, val %s\n", | |
| pin, | |
| slpm_pull ? pullnames[pull] : "same", | |
| slpm_output ? (output ? "output" : "input") | |
| : "same", | |
| slpm_val ? (val ? "high" : "low") : "same"); | |
| } | |
| dev_dbg(nmk_chip->chip.parent, | |
| "pin %d [%#lx]: pull %s, slpm %s (%s%s), lowemi %s\n", | |
| pin, cfg, pullnames[pull], slpmnames[slpm], | |
| output ? "output " : "input", | |
| output ? (val ? "high" : "low") : "", | |
| lowemi ? "on" : "off"); | |
| clk_enable(nmk_chip->clk); | |
| bit = pin % NMK_GPIO_PER_CHIP; | |
| if (gpiomode) | |
| /* No glitch when going to GPIO mode */ | |
| __nmk_gpio_set_mode(nmk_chip, bit, NMK_GPIO_ALT_GPIO); | |
| if (output) | |
| __nmk_gpio_make_output(nmk_chip, bit, val); | |
| else { | |
| __nmk_gpio_make_input(nmk_chip, bit); | |
| __nmk_gpio_set_pull(nmk_chip, bit, pull); | |
| } | |
| /* TODO: isn't this only applicable on output pins? */ | |
| __nmk_gpio_set_lowemi(nmk_chip, bit, lowemi); | |
| __nmk_gpio_set_slpm(nmk_chip, bit, slpm); | |
| clk_disable(nmk_chip->clk); | |
| } /* for each config */ | |
| return 0; | |
| } | |
| static const struct pinconf_ops nmk_pinconf_ops = { | |
| .pin_config_get = nmk_pin_config_get, | |
| .pin_config_set = nmk_pin_config_set, | |
| }; | |
| static struct pinctrl_desc nmk_pinctrl_desc = { | |
| .name = "pinctrl-nomadik", | |
| .pctlops = &nmk_pinctrl_ops, | |
| .pmxops = &nmk_pinmux_ops, | |
| .confops = &nmk_pinconf_ops, | |
| .owner = THIS_MODULE, | |
| }; | |
| static const struct of_device_id nmk_pinctrl_match[] = { | |
| { | |
| .compatible = "stericsson,stn8815-pinctrl", | |
| .data = (void *)PINCTRL_NMK_STN8815, | |
| }, | |
| { | |
| .compatible = "stericsson,db8500-pinctrl", | |
| .data = (void *)PINCTRL_NMK_DB8500, | |
| }, | |
| { | |
| .compatible = "stericsson,db8540-pinctrl", | |
| .data = (void *)PINCTRL_NMK_DB8540, | |
| }, | |
| {}, | |
| }; | |
| #ifdef CONFIG_PM_SLEEP | |
| static int nmk_pinctrl_suspend(struct device *dev) | |
| { | |
| struct nmk_pinctrl *npct; | |
| npct = dev_get_drvdata(dev); | |
| if (!npct) | |
| return -EINVAL; | |
| return pinctrl_force_sleep(npct->pctl); | |
| } | |
| static int nmk_pinctrl_resume(struct device *dev) | |
| { | |
| struct nmk_pinctrl *npct; | |
| npct = dev_get_drvdata(dev); | |
| if (!npct) | |
| return -EINVAL; | |
| return pinctrl_force_default(npct->pctl); | |
| } | |
| #endif | |
| static int nmk_pinctrl_probe(struct platform_device *pdev) | |
| { | |
| const struct of_device_id *match; | |
| struct device_node *np = pdev->dev.of_node; | |
| struct device_node *prcm_np; | |
| struct nmk_pinctrl *npct; | |
| unsigned int version = 0; | |
| int i; | |
| npct = devm_kzalloc(&pdev->dev, sizeof(*npct), GFP_KERNEL); | |
| if (!npct) | |
| return -ENOMEM; | |
| match = of_match_device(nmk_pinctrl_match, &pdev->dev); | |
| if (!match) | |
| return -ENODEV; | |
| version = (unsigned int) match->data; | |
| /* Poke in other ASIC variants here */ | |
| if (version == PINCTRL_NMK_STN8815) | |
| nmk_pinctrl_stn8815_init(&npct->soc); | |
| if (version == PINCTRL_NMK_DB8500) | |
| nmk_pinctrl_db8500_init(&npct->soc); | |
| if (version == PINCTRL_NMK_DB8540) | |
| nmk_pinctrl_db8540_init(&npct->soc); | |
| /* | |
| * Since we depend on the GPIO chips to provide clock and register base | |
| * for the pin control operations, make sure that we have these | |
| * populated before we continue. Follow the phandles to instantiate | |
| * them. The GPIO portion of the actual hardware may be probed before | |
| * or after this point: it shouldn't matter as the APIs are orthogonal. | |
| */ | |
| for (i = 0; i < NMK_MAX_BANKS; i++) { | |
| struct device_node *gpio_np; | |
| struct nmk_gpio_chip *nmk_chip; | |
| gpio_np = of_parse_phandle(np, "nomadik-gpio-chips", i); | |
| if (gpio_np) { | |
| dev_info(&pdev->dev, | |
| "populate NMK GPIO %d \"%s\"\n", | |
| i, gpio_np->name); | |
| nmk_chip = nmk_gpio_populate_chip(gpio_np, pdev); | |
| if (IS_ERR(nmk_chip)) | |
| dev_err(&pdev->dev, | |
| "could not populate nmk chip struct " | |
| "- continue anyway\n"); | |
| of_node_put(gpio_np); | |
| } | |
| } | |
| prcm_np = of_parse_phandle(np, "prcm", 0); | |
| if (prcm_np) | |
| npct->prcm_base = of_iomap(prcm_np, 0); | |
| if (!npct->prcm_base) { | |
| if (version == PINCTRL_NMK_STN8815) { | |
| dev_info(&pdev->dev, | |
| "No PRCM base, " | |
| "assuming no ALT-Cx control is available\n"); | |
| } else { | |
| dev_err(&pdev->dev, "missing PRCM base address\n"); | |
| return -EINVAL; | |
| } | |
| } | |
| nmk_pinctrl_desc.pins = npct->soc->pins; | |
| nmk_pinctrl_desc.npins = npct->soc->npins; | |
| npct->dev = &pdev->dev; | |
| npct->pctl = devm_pinctrl_register(&pdev->dev, &nmk_pinctrl_desc, npct); | |
| if (IS_ERR(npct->pctl)) { | |
| dev_err(&pdev->dev, "could not register Nomadik pinctrl driver\n"); | |
| return PTR_ERR(npct->pctl); | |
| } | |
| platform_set_drvdata(pdev, npct); | |
| dev_info(&pdev->dev, "initialized Nomadik pin control driver\n"); | |
| return 0; | |
| } | |
| static const struct of_device_id nmk_gpio_match[] = { | |
| { .compatible = "st,nomadik-gpio", }, | |
| {} | |
| }; | |
| static struct platform_driver nmk_gpio_driver = { | |
| .driver = { | |
| .name = "gpio", | |
| .of_match_table = nmk_gpio_match, | |
| }, | |
| .probe = nmk_gpio_probe, | |
| }; | |
| static SIMPLE_DEV_PM_OPS(nmk_pinctrl_pm_ops, | |
| nmk_pinctrl_suspend, | |
| nmk_pinctrl_resume); | |
| static struct platform_driver nmk_pinctrl_driver = { | |
| .driver = { | |
| .name = "pinctrl-nomadik", | |
| .of_match_table = nmk_pinctrl_match, | |
| .pm = &nmk_pinctrl_pm_ops, | |
| }, | |
| .probe = nmk_pinctrl_probe, | |
| }; | |
| static int __init nmk_gpio_init(void) | |
| { | |
| return platform_driver_register(&nmk_gpio_driver); | |
| } | |
| subsys_initcall(nmk_gpio_init); | |
| static int __init nmk_pinctrl_init(void) | |
| { | |
| return platform_driver_register(&nmk_pinctrl_driver); | |
| } | |
| core_initcall(nmk_pinctrl_init); |