| /* | |
| * twl-regulator.c -- support regulators in twl4030/twl6030 family chips | |
| * | |
| * Copyright (C) 2008 David Brownell | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License as published by | |
| * the Free Software Foundation; either version 2 of the License, or | |
| * (at your option) any later version. | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/string.h> | |
| #include <linux/slab.h> | |
| #include <linux/init.h> | |
| #include <linux/err.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/of.h> | |
| #include <linux/of_device.h> | |
| #include <linux/regulator/driver.h> | |
| #include <linux/regulator/machine.h> | |
| #include <linux/regulator/of_regulator.h> | |
| #include <linux/i2c/twl.h> | |
| #include <linux/delay.h> | |
| /* | |
| * The TWL4030/TW5030/TPS659x0/TWL6030 family chips include power management, a | |
| * USB OTG transceiver, an RTC, ADC, PWM, and lots more. Some versions | |
| * include an audio codec, battery charger, and more voltage regulators. | |
| * These chips are often used in OMAP-based systems. | |
| * | |
| * This driver implements software-based resource control for various | |
| * voltage regulators. This is usually augmented with state machine | |
| * based control. | |
| */ | |
| struct twlreg_info { | |
| /* start of regulator's PM_RECEIVER control register bank */ | |
| u8 base; | |
| /* twl resource ID, for resource control state machine */ | |
| u8 id; | |
| /* voltage in mV = table[VSEL]; table_len must be a power-of-two */ | |
| u8 table_len; | |
| const u16 *table; | |
| /* State REMAP default configuration */ | |
| u8 remap; | |
| /* chip constraints on regulator behavior */ | |
| u16 min_mV; | |
| u16 max_mV; | |
| u8 flags; | |
| /* used by regulator core */ | |
| struct regulator_desc desc; | |
| /* chip specific features */ | |
| unsigned long features; | |
| /* | |
| * optional override functions for voltage set/get | |
| * these are currently only used for SMPS regulators | |
| */ | |
| int (*get_voltage)(void *data); | |
| int (*set_voltage)(void *data, int target_uV); | |
| /* data passed from board for external get/set voltage */ | |
| void *data; | |
| }; | |
| /* LDO control registers ... offset is from the base of its register bank. | |
| * The first three registers of all power resource banks help hardware to | |
| * manage the various resource groups. | |
| */ | |
| /* Common offset in TWL4030/6030 */ | |
| #define VREG_GRP 0 | |
| /* TWL4030 register offsets */ | |
| #define VREG_TYPE 1 | |
| #define VREG_REMAP 2 | |
| #define VREG_DEDICATED 3 /* LDO control */ | |
| #define VREG_VOLTAGE_SMPS_4030 9 | |
| /* TWL6030 register offsets */ | |
| #define VREG_TRANS 1 | |
| #define VREG_STATE 2 | |
| #define VREG_VOLTAGE 3 | |
| #define VREG_VOLTAGE_SMPS 4 | |
| /* TWL6030 Misc register offsets */ | |
| #define VREG_BC_ALL 1 | |
| #define VREG_BC_REF 2 | |
| #define VREG_BC_PROC 3 | |
| #define VREG_BC_CLK_RST 4 | |
| /* TWL6030 LDO register values for CFG_STATE */ | |
| #define TWL6030_CFG_STATE_OFF 0x00 | |
| #define TWL6030_CFG_STATE_ON 0x01 | |
| #define TWL6030_CFG_STATE_OFF2 0x02 | |
| #define TWL6030_CFG_STATE_SLEEP 0x03 | |
| #define TWL6030_CFG_STATE_GRP_SHIFT 5 | |
| #define TWL6030_CFG_STATE_APP_SHIFT 2 | |
| #define TWL6030_CFG_STATE_APP_MASK (0x03 << TWL6030_CFG_STATE_APP_SHIFT) | |
| #define TWL6030_CFG_STATE_APP(v) (((v) & TWL6030_CFG_STATE_APP_MASK) >>\ | |
| TWL6030_CFG_STATE_APP_SHIFT) | |
| /* Flags for SMPS Voltage reading */ | |
| #define SMPS_OFFSET_EN BIT(0) | |
| #define SMPS_EXTENDED_EN BIT(1) | |
| /* twl6032 SMPS EPROM values */ | |
| #define TWL6030_SMPS_OFFSET 0xB0 | |
| #define TWL6030_SMPS_MULT 0xB3 | |
| #define SMPS_MULTOFFSET_SMPS4 BIT(0) | |
| #define SMPS_MULTOFFSET_VIO BIT(1) | |
| #define SMPS_MULTOFFSET_SMPS3 BIT(6) | |
| static inline int | |
| twlreg_read(struct twlreg_info *info, unsigned slave_subgp, unsigned offset) | |
| { | |
| u8 value; | |
| int status; | |
| status = twl_i2c_read_u8(slave_subgp, | |
| &value, info->base + offset); | |
| return (status < 0) ? status : value; | |
| } | |
| static inline int | |
| twlreg_write(struct twlreg_info *info, unsigned slave_subgp, unsigned offset, | |
| u8 value) | |
| { | |
| return twl_i2c_write_u8(slave_subgp, | |
| value, info->base + offset); | |
| } | |
| /*----------------------------------------------------------------------*/ | |
| /* generic power resource operations, which work on all regulators */ | |
| static int twlreg_grp(struct regulator_dev *rdev) | |
| { | |
| return twlreg_read(rdev_get_drvdata(rdev), TWL_MODULE_PM_RECEIVER, | |
| VREG_GRP); | |
| } | |
| /* | |
| * Enable/disable regulators by joining/leaving the P1 (processor) group. | |
| * We assume nobody else is updating the DEV_GRP registers. | |
| */ | |
| /* definition for 4030 family */ | |
| #define P3_GRP_4030 BIT(7) /* "peripherals" */ | |
| #define P2_GRP_4030 BIT(6) /* secondary processor, modem, etc */ | |
| #define P1_GRP_4030 BIT(5) /* CPU/Linux */ | |
| /* definition for 6030 family */ | |
| #define P3_GRP_6030 BIT(2) /* secondary processor, modem, etc */ | |
| #define P2_GRP_6030 BIT(1) /* "peripherals" */ | |
| #define P1_GRP_6030 BIT(0) /* CPU/Linux */ | |
| static int twl4030reg_is_enabled(struct regulator_dev *rdev) | |
| { | |
| int state = twlreg_grp(rdev); | |
| if (state < 0) | |
| return state; | |
| return state & P1_GRP_4030; | |
| } | |
| static int twl6030reg_is_enabled(struct regulator_dev *rdev) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int grp = 0, val; | |
| if (!(twl_class_is_6030() && (info->features & TWL6032_SUBCLASS))) { | |
| grp = twlreg_grp(rdev); | |
| if (grp < 0) | |
| return grp; | |
| grp &= P1_GRP_6030; | |
| } else { | |
| grp = 1; | |
| } | |
| val = twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_STATE); | |
| val = TWL6030_CFG_STATE_APP(val); | |
| return grp && (val == TWL6030_CFG_STATE_ON); | |
| } | |
| #define PB_I2C_BUSY BIT(0) | |
| #define PB_I2C_BWEN BIT(1) | |
| /* Wait until buffer empty/ready to send a word on power bus. */ | |
| static int twl4030_wait_pb_ready(void) | |
| { | |
| int ret; | |
| int timeout = 10; | |
| u8 val; | |
| do { | |
| ret = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &val, | |
| TWL4030_PM_MASTER_PB_CFG); | |
| if (ret < 0) | |
| return ret; | |
| if (!(val & PB_I2C_BUSY)) | |
| return 0; | |
| mdelay(1); | |
| timeout--; | |
| } while (timeout); | |
| return -ETIMEDOUT; | |
| } | |
| /* Send a word over the powerbus */ | |
| static int twl4030_send_pb_msg(unsigned msg) | |
| { | |
| u8 val; | |
| int ret; | |
| /* save powerbus configuration */ | |
| ret = twl_i2c_read_u8(TWL_MODULE_PM_MASTER, &val, | |
| TWL4030_PM_MASTER_PB_CFG); | |
| if (ret < 0) | |
| return ret; | |
| /* Enable i2c access to powerbus */ | |
| ret = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, val | PB_I2C_BWEN, | |
| TWL4030_PM_MASTER_PB_CFG); | |
| if (ret < 0) | |
| return ret; | |
| ret = twl4030_wait_pb_ready(); | |
| if (ret < 0) | |
| return ret; | |
| ret = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, msg >> 8, | |
| TWL4030_PM_MASTER_PB_WORD_MSB); | |
| if (ret < 0) | |
| return ret; | |
| ret = twl_i2c_write_u8(TWL_MODULE_PM_MASTER, msg & 0xff, | |
| TWL4030_PM_MASTER_PB_WORD_LSB); | |
| if (ret < 0) | |
| return ret; | |
| ret = twl4030_wait_pb_ready(); | |
| if (ret < 0) | |
| return ret; | |
| /* Restore powerbus configuration */ | |
| return twl_i2c_write_u8(TWL_MODULE_PM_MASTER, val, | |
| TWL4030_PM_MASTER_PB_CFG); | |
| } | |
| static int twl4030reg_enable(struct regulator_dev *rdev) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int grp; | |
| int ret; | |
| grp = twlreg_grp(rdev); | |
| if (grp < 0) | |
| return grp; | |
| grp |= P1_GRP_4030; | |
| ret = twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_GRP, grp); | |
| return ret; | |
| } | |
| static int twl6030reg_enable(struct regulator_dev *rdev) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int grp = 0; | |
| int ret; | |
| if (!(twl_class_is_6030() && (info->features & TWL6032_SUBCLASS))) | |
| grp = twlreg_grp(rdev); | |
| if (grp < 0) | |
| return grp; | |
| ret = twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_STATE, | |
| grp << TWL6030_CFG_STATE_GRP_SHIFT | | |
| TWL6030_CFG_STATE_ON); | |
| return ret; | |
| } | |
| static int twl4030reg_disable(struct regulator_dev *rdev) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int grp; | |
| int ret; | |
| grp = twlreg_grp(rdev); | |
| if (grp < 0) | |
| return grp; | |
| grp &= ~(P1_GRP_4030 | P2_GRP_4030 | P3_GRP_4030); | |
| ret = twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_GRP, grp); | |
| return ret; | |
| } | |
| static int twl6030reg_disable(struct regulator_dev *rdev) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int grp = 0; | |
| int ret; | |
| if (!(twl_class_is_6030() && (info->features & TWL6032_SUBCLASS))) | |
| grp = P1_GRP_6030 | P2_GRP_6030 | P3_GRP_6030; | |
| /* For 6030, set the off state for all grps enabled */ | |
| ret = twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_STATE, | |
| (grp) << TWL6030_CFG_STATE_GRP_SHIFT | | |
| TWL6030_CFG_STATE_OFF); | |
| return ret; | |
| } | |
| static int twl4030reg_get_status(struct regulator_dev *rdev) | |
| { | |
| int state = twlreg_grp(rdev); | |
| if (state < 0) | |
| return state; | |
| state &= 0x0f; | |
| /* assume state != WARM_RESET; we'd not be running... */ | |
| if (!state) | |
| return REGULATOR_STATUS_OFF; | |
| return (state & BIT(3)) | |
| ? REGULATOR_STATUS_NORMAL | |
| : REGULATOR_STATUS_STANDBY; | |
| } | |
| static int twl6030reg_get_status(struct regulator_dev *rdev) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int val; | |
| val = twlreg_grp(rdev); | |
| if (val < 0) | |
| return val; | |
| val = twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_STATE); | |
| switch (TWL6030_CFG_STATE_APP(val)) { | |
| case TWL6030_CFG_STATE_ON: | |
| return REGULATOR_STATUS_NORMAL; | |
| case TWL6030_CFG_STATE_SLEEP: | |
| return REGULATOR_STATUS_STANDBY; | |
| case TWL6030_CFG_STATE_OFF: | |
| case TWL6030_CFG_STATE_OFF2: | |
| default: | |
| break; | |
| } | |
| return REGULATOR_STATUS_OFF; | |
| } | |
| static int twl4030reg_set_mode(struct regulator_dev *rdev, unsigned mode) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| unsigned message; | |
| /* We can only set the mode through state machine commands... */ | |
| switch (mode) { | |
| case REGULATOR_MODE_NORMAL: | |
| message = MSG_SINGULAR(DEV_GRP_P1, info->id, RES_STATE_ACTIVE); | |
| break; | |
| case REGULATOR_MODE_STANDBY: | |
| message = MSG_SINGULAR(DEV_GRP_P1, info->id, RES_STATE_SLEEP); | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| return twl4030_send_pb_msg(message); | |
| } | |
| static inline unsigned int twl4030reg_map_mode(unsigned int mode) | |
| { | |
| switch (mode) { | |
| case RES_STATE_ACTIVE: | |
| return REGULATOR_MODE_NORMAL; | |
| case RES_STATE_SLEEP: | |
| return REGULATOR_MODE_STANDBY; | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| static int twl6030reg_set_mode(struct regulator_dev *rdev, unsigned mode) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int grp = 0; | |
| int val; | |
| if (!(twl_class_is_6030() && (info->features & TWL6032_SUBCLASS))) | |
| grp = twlreg_grp(rdev); | |
| if (grp < 0) | |
| return grp; | |
| /* Compose the state register settings */ | |
| val = grp << TWL6030_CFG_STATE_GRP_SHIFT; | |
| /* We can only set the mode through state machine commands... */ | |
| switch (mode) { | |
| case REGULATOR_MODE_NORMAL: | |
| val |= TWL6030_CFG_STATE_ON; | |
| break; | |
| case REGULATOR_MODE_STANDBY: | |
| val |= TWL6030_CFG_STATE_SLEEP; | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| return twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_STATE, val); | |
| } | |
| /*----------------------------------------------------------------------*/ | |
| /* | |
| * Support for adjustable-voltage LDOs uses a four bit (or less) voltage | |
| * select field in its control register. We use tables indexed by VSEL | |
| * to record voltages in milliVolts. (Accuracy is about three percent.) | |
| * | |
| * Note that VSEL values for VAUX2 changed in twl5030 and newer silicon; | |
| * currently handled by listing two slightly different VAUX2 regulators, | |
| * only one of which will be configured. | |
| * | |
| * VSEL values documented as "TI cannot support these values" are flagged | |
| * in these tables as UNSUP() values; we normally won't assign them. | |
| * | |
| * VAUX3 at 3V is incorrectly listed in some TI manuals as unsupported. | |
| * TI are revising the twl5030/tps659x0 specs to support that 3.0V setting. | |
| */ | |
| #define UNSUP_MASK 0x8000 | |
| #define UNSUP(x) (UNSUP_MASK | (x)) | |
| #define IS_UNSUP(info, x) \ | |
| ((UNSUP_MASK & (x)) && \ | |
| !((info)->features & TWL4030_ALLOW_UNSUPPORTED)) | |
| #define LDO_MV(x) (~UNSUP_MASK & (x)) | |
| static const u16 VAUX1_VSEL_table[] = { | |
| UNSUP(1500), UNSUP(1800), 2500, 2800, | |
| 3000, 3000, 3000, 3000, | |
| }; | |
| static const u16 VAUX2_4030_VSEL_table[] = { | |
| UNSUP(1000), UNSUP(1000), UNSUP(1200), 1300, | |
| 1500, 1800, UNSUP(1850), 2500, | |
| UNSUP(2600), 2800, UNSUP(2850), UNSUP(3000), | |
| UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), | |
| }; | |
| static const u16 VAUX2_VSEL_table[] = { | |
| 1700, 1700, 1900, 1300, | |
| 1500, 1800, 2000, 2500, | |
| 2100, 2800, 2200, 2300, | |
| 2400, 2400, 2400, 2400, | |
| }; | |
| static const u16 VAUX3_VSEL_table[] = { | |
| 1500, 1800, 2500, 2800, | |
| 3000, 3000, 3000, 3000, | |
| }; | |
| static const u16 VAUX4_VSEL_table[] = { | |
| 700, 1000, 1200, UNSUP(1300), | |
| 1500, 1800, UNSUP(1850), 2500, | |
| UNSUP(2600), 2800, UNSUP(2850), UNSUP(3000), | |
| UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), | |
| }; | |
| static const u16 VMMC1_VSEL_table[] = { | |
| 1850, 2850, 3000, 3150, | |
| }; | |
| static const u16 VMMC2_VSEL_table[] = { | |
| UNSUP(1000), UNSUP(1000), UNSUP(1200), UNSUP(1300), | |
| UNSUP(1500), UNSUP(1800), 1850, UNSUP(2500), | |
| 2600, 2800, 2850, 3000, | |
| 3150, 3150, 3150, 3150, | |
| }; | |
| static const u16 VPLL1_VSEL_table[] = { | |
| 1000, 1200, 1300, 1800, | |
| UNSUP(2800), UNSUP(3000), UNSUP(3000), UNSUP(3000), | |
| }; | |
| static const u16 VPLL2_VSEL_table[] = { | |
| 700, 1000, 1200, 1300, | |
| UNSUP(1500), 1800, UNSUP(1850), UNSUP(2500), | |
| UNSUP(2600), UNSUP(2800), UNSUP(2850), UNSUP(3000), | |
| UNSUP(3150), UNSUP(3150), UNSUP(3150), UNSUP(3150), | |
| }; | |
| static const u16 VSIM_VSEL_table[] = { | |
| UNSUP(1000), UNSUP(1200), UNSUP(1300), 1800, | |
| 2800, 3000, 3000, 3000, | |
| }; | |
| static const u16 VDAC_VSEL_table[] = { | |
| 1200, 1300, 1800, 1800, | |
| }; | |
| static const u16 VIO_VSEL_table[] = { | |
| 1800, 1850, | |
| }; | |
| static const u16 VINTANA2_VSEL_table[] = { | |
| 2500, 2750, | |
| }; | |
| static int twl4030ldo_list_voltage(struct regulator_dev *rdev, unsigned index) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int mV = info->table[index]; | |
| return IS_UNSUP(info, mV) ? 0 : (LDO_MV(mV) * 1000); | |
| } | |
| static int | |
| twl4030ldo_set_voltage_sel(struct regulator_dev *rdev, unsigned selector) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| return twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE, | |
| selector); | |
| } | |
| static int twl4030ldo_get_voltage_sel(struct regulator_dev *rdev) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int vsel = twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE); | |
| if (vsel < 0) | |
| return vsel; | |
| vsel &= info->table_len - 1; | |
| return vsel; | |
| } | |
| static struct regulator_ops twl4030ldo_ops = { | |
| .list_voltage = twl4030ldo_list_voltage, | |
| .set_voltage_sel = twl4030ldo_set_voltage_sel, | |
| .get_voltage_sel = twl4030ldo_get_voltage_sel, | |
| .enable = twl4030reg_enable, | |
| .disable = twl4030reg_disable, | |
| .is_enabled = twl4030reg_is_enabled, | |
| .set_mode = twl4030reg_set_mode, | |
| .get_status = twl4030reg_get_status, | |
| }; | |
| static int | |
| twl4030smps_set_voltage(struct regulator_dev *rdev, int min_uV, int max_uV, | |
| unsigned *selector) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int vsel = DIV_ROUND_UP(min_uV - 600000, 12500); | |
| if (info->set_voltage) { | |
| return info->set_voltage(info->data, min_uV); | |
| } else { | |
| twlreg_write(info, TWL_MODULE_PM_RECEIVER, | |
| VREG_VOLTAGE_SMPS_4030, vsel); | |
| } | |
| return 0; | |
| } | |
| static int twl4030smps_get_voltage(struct regulator_dev *rdev) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int vsel; | |
| if (info->get_voltage) | |
| return info->get_voltage(info->data); | |
| vsel = twlreg_read(info, TWL_MODULE_PM_RECEIVER, | |
| VREG_VOLTAGE_SMPS_4030); | |
| return vsel * 12500 + 600000; | |
| } | |
| static struct regulator_ops twl4030smps_ops = { | |
| .set_voltage = twl4030smps_set_voltage, | |
| .get_voltage = twl4030smps_get_voltage, | |
| }; | |
| static int twl6030coresmps_set_voltage(struct regulator_dev *rdev, int min_uV, | |
| int max_uV, unsigned *selector) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| if (info->set_voltage) | |
| return info->set_voltage(info->data, min_uV); | |
| return -ENODEV; | |
| } | |
| static int twl6030coresmps_get_voltage(struct regulator_dev *rdev) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| if (info->get_voltage) | |
| return info->get_voltage(info->data); | |
| return -ENODEV; | |
| } | |
| static struct regulator_ops twl6030coresmps_ops = { | |
| .set_voltage = twl6030coresmps_set_voltage, | |
| .get_voltage = twl6030coresmps_get_voltage, | |
| }; | |
| static int twl6030ldo_list_voltage(struct regulator_dev *rdev, unsigned sel) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| switch (sel) { | |
| case 0: | |
| return 0; | |
| case 1 ... 24: | |
| /* Linear mapping from 00000001 to 00011000: | |
| * Absolute voltage value = 1.0 V + 0.1 V × (sel – 00000001) | |
| */ | |
| return (info->min_mV + 100 * (sel - 1)) * 1000; | |
| case 25 ... 30: | |
| return -EINVAL; | |
| case 31: | |
| return 2750000; | |
| default: | |
| return -EINVAL; | |
| } | |
| } | |
| static int | |
| twl6030ldo_set_voltage_sel(struct regulator_dev *rdev, unsigned selector) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| return twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE, | |
| selector); | |
| } | |
| static int twl6030ldo_get_voltage_sel(struct regulator_dev *rdev) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int vsel = twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE); | |
| return vsel; | |
| } | |
| static struct regulator_ops twl6030ldo_ops = { | |
| .list_voltage = twl6030ldo_list_voltage, | |
| .set_voltage_sel = twl6030ldo_set_voltage_sel, | |
| .get_voltage_sel = twl6030ldo_get_voltage_sel, | |
| .enable = twl6030reg_enable, | |
| .disable = twl6030reg_disable, | |
| .is_enabled = twl6030reg_is_enabled, | |
| .set_mode = twl6030reg_set_mode, | |
| .get_status = twl6030reg_get_status, | |
| }; | |
| /*----------------------------------------------------------------------*/ | |
| static struct regulator_ops twl4030fixed_ops = { | |
| .list_voltage = regulator_list_voltage_linear, | |
| .enable = twl4030reg_enable, | |
| .disable = twl4030reg_disable, | |
| .is_enabled = twl4030reg_is_enabled, | |
| .set_mode = twl4030reg_set_mode, | |
| .get_status = twl4030reg_get_status, | |
| }; | |
| static struct regulator_ops twl6030fixed_ops = { | |
| .list_voltage = regulator_list_voltage_linear, | |
| .enable = twl6030reg_enable, | |
| .disable = twl6030reg_disable, | |
| .is_enabled = twl6030reg_is_enabled, | |
| .set_mode = twl6030reg_set_mode, | |
| .get_status = twl6030reg_get_status, | |
| }; | |
| /* | |
| * SMPS status and control | |
| */ | |
| static int twl6030smps_list_voltage(struct regulator_dev *rdev, unsigned index) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int voltage = 0; | |
| switch (info->flags) { | |
| case SMPS_OFFSET_EN: | |
| voltage = 100000; | |
| /* fall through */ | |
| case 0: | |
| switch (index) { | |
| case 0: | |
| voltage = 0; | |
| break; | |
| case 58: | |
| voltage = 1350 * 1000; | |
| break; | |
| case 59: | |
| voltage = 1500 * 1000; | |
| break; | |
| case 60: | |
| voltage = 1800 * 1000; | |
| break; | |
| case 61: | |
| voltage = 1900 * 1000; | |
| break; | |
| case 62: | |
| voltage = 2100 * 1000; | |
| break; | |
| default: | |
| voltage += (600000 + (12500 * (index - 1))); | |
| } | |
| break; | |
| case SMPS_EXTENDED_EN: | |
| switch (index) { | |
| case 0: | |
| voltage = 0; | |
| break; | |
| case 58: | |
| voltage = 2084 * 1000; | |
| break; | |
| case 59: | |
| voltage = 2315 * 1000; | |
| break; | |
| case 60: | |
| voltage = 2778 * 1000; | |
| break; | |
| case 61: | |
| voltage = 2932 * 1000; | |
| break; | |
| case 62: | |
| voltage = 3241 * 1000; | |
| break; | |
| default: | |
| voltage = (1852000 + (38600 * (index - 1))); | |
| } | |
| break; | |
| case SMPS_OFFSET_EN | SMPS_EXTENDED_EN: | |
| switch (index) { | |
| case 0: | |
| voltage = 0; | |
| break; | |
| case 58: | |
| voltage = 4167 * 1000; | |
| break; | |
| case 59: | |
| voltage = 2315 * 1000; | |
| break; | |
| case 60: | |
| voltage = 2778 * 1000; | |
| break; | |
| case 61: | |
| voltage = 2932 * 1000; | |
| break; | |
| case 62: | |
| voltage = 3241 * 1000; | |
| break; | |
| default: | |
| voltage = (2161000 + (38600 * (index - 1))); | |
| } | |
| break; | |
| } | |
| return voltage; | |
| } | |
| static int twl6030smps_map_voltage(struct regulator_dev *rdev, int min_uV, | |
| int max_uV) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| int vsel = 0; | |
| switch (info->flags) { | |
| case 0: | |
| if (min_uV == 0) | |
| vsel = 0; | |
| else if ((min_uV >= 600000) && (min_uV <= 1300000)) { | |
| vsel = DIV_ROUND_UP(min_uV - 600000, 12500); | |
| vsel++; | |
| } | |
| /* Values 1..57 for vsel are linear and can be calculated | |
| * values 58..62 are non linear. | |
| */ | |
| else if ((min_uV > 1900000) && (min_uV <= 2100000)) | |
| vsel = 62; | |
| else if ((min_uV > 1800000) && (min_uV <= 1900000)) | |
| vsel = 61; | |
| else if ((min_uV > 1500000) && (min_uV <= 1800000)) | |
| vsel = 60; | |
| else if ((min_uV > 1350000) && (min_uV <= 1500000)) | |
| vsel = 59; | |
| else if ((min_uV > 1300000) && (min_uV <= 1350000)) | |
| vsel = 58; | |
| else | |
| return -EINVAL; | |
| break; | |
| case SMPS_OFFSET_EN: | |
| if (min_uV == 0) | |
| vsel = 0; | |
| else if ((min_uV >= 700000) && (min_uV <= 1420000)) { | |
| vsel = DIV_ROUND_UP(min_uV - 700000, 12500); | |
| vsel++; | |
| } | |
| /* Values 1..57 for vsel are linear and can be calculated | |
| * values 58..62 are non linear. | |
| */ | |
| else if ((min_uV > 1900000) && (min_uV <= 2100000)) | |
| vsel = 62; | |
| else if ((min_uV > 1800000) && (min_uV <= 1900000)) | |
| vsel = 61; | |
| else if ((min_uV > 1350000) && (min_uV <= 1800000)) | |
| vsel = 60; | |
| else if ((min_uV > 1350000) && (min_uV <= 1500000)) | |
| vsel = 59; | |
| else if ((min_uV > 1300000) && (min_uV <= 1350000)) | |
| vsel = 58; | |
| else | |
| return -EINVAL; | |
| break; | |
| case SMPS_EXTENDED_EN: | |
| if (min_uV == 0) { | |
| vsel = 0; | |
| } else if ((min_uV >= 1852000) && (max_uV <= 4013600)) { | |
| vsel = DIV_ROUND_UP(min_uV - 1852000, 38600); | |
| vsel++; | |
| } | |
| break; | |
| case SMPS_OFFSET_EN|SMPS_EXTENDED_EN: | |
| if (min_uV == 0) { | |
| vsel = 0; | |
| } else if ((min_uV >= 2161000) && (min_uV <= 4321000)) { | |
| vsel = DIV_ROUND_UP(min_uV - 2161000, 38600); | |
| vsel++; | |
| } | |
| break; | |
| } | |
| return vsel; | |
| } | |
| static int twl6030smps_set_voltage_sel(struct regulator_dev *rdev, | |
| unsigned int selector) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| return twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE_SMPS, | |
| selector); | |
| } | |
| static int twl6030smps_get_voltage_sel(struct regulator_dev *rdev) | |
| { | |
| struct twlreg_info *info = rdev_get_drvdata(rdev); | |
| return twlreg_read(info, TWL_MODULE_PM_RECEIVER, VREG_VOLTAGE_SMPS); | |
| } | |
| static struct regulator_ops twlsmps_ops = { | |
| .list_voltage = twl6030smps_list_voltage, | |
| .map_voltage = twl6030smps_map_voltage, | |
| .set_voltage_sel = twl6030smps_set_voltage_sel, | |
| .get_voltage_sel = twl6030smps_get_voltage_sel, | |
| .enable = twl6030reg_enable, | |
| .disable = twl6030reg_disable, | |
| .is_enabled = twl6030reg_is_enabled, | |
| .set_mode = twl6030reg_set_mode, | |
| .get_status = twl6030reg_get_status, | |
| }; | |
| /*----------------------------------------------------------------------*/ | |
| #define TWL4030_FIXED_LDO(label, offset, mVolts, num, turnon_delay, \ | |
| remap_conf) \ | |
| TWL_FIXED_LDO(label, offset, mVolts, num, turnon_delay, \ | |
| remap_conf, TWL4030, twl4030fixed_ops, \ | |
| twl4030reg_map_mode) | |
| #define TWL6030_FIXED_LDO(label, offset, mVolts, turnon_delay) \ | |
| TWL_FIXED_LDO(label, offset, mVolts, 0x0, turnon_delay, \ | |
| 0x0, TWL6030, twl6030fixed_ops, NULL) | |
| #define TWL4030_ADJUSTABLE_LDO(label, offset, num, turnon_delay, remap_conf) \ | |
| static const struct twlreg_info TWL4030_INFO_##label = { \ | |
| .base = offset, \ | |
| .id = num, \ | |
| .table_len = ARRAY_SIZE(label##_VSEL_table), \ | |
| .table = label##_VSEL_table, \ | |
| .remap = remap_conf, \ | |
| .desc = { \ | |
| .name = #label, \ | |
| .id = TWL4030_REG_##label, \ | |
| .n_voltages = ARRAY_SIZE(label##_VSEL_table), \ | |
| .ops = &twl4030ldo_ops, \ | |
| .type = REGULATOR_VOLTAGE, \ | |
| .owner = THIS_MODULE, \ | |
| .enable_time = turnon_delay, \ | |
| .of_map_mode = twl4030reg_map_mode, \ | |
| }, \ | |
| } | |
| #define TWL4030_ADJUSTABLE_SMPS(label, offset, num, turnon_delay, remap_conf) \ | |
| static const struct twlreg_info TWL4030_INFO_##label = { \ | |
| .base = offset, \ | |
| .id = num, \ | |
| .remap = remap_conf, \ | |
| .desc = { \ | |
| .name = #label, \ | |
| .id = TWL4030_REG_##label, \ | |
| .ops = &twl4030smps_ops, \ | |
| .type = REGULATOR_VOLTAGE, \ | |
| .owner = THIS_MODULE, \ | |
| .enable_time = turnon_delay, \ | |
| .of_map_mode = twl4030reg_map_mode, \ | |
| }, \ | |
| } | |
| #define TWL6030_ADJUSTABLE_SMPS(label) \ | |
| static const struct twlreg_info TWL6030_INFO_##label = { \ | |
| .desc = { \ | |
| .name = #label, \ | |
| .id = TWL6030_REG_##label, \ | |
| .ops = &twl6030coresmps_ops, \ | |
| .type = REGULATOR_VOLTAGE, \ | |
| .owner = THIS_MODULE, \ | |
| }, \ | |
| } | |
| #define TWL6030_ADJUSTABLE_LDO(label, offset, min_mVolts, max_mVolts) \ | |
| static const struct twlreg_info TWL6030_INFO_##label = { \ | |
| .base = offset, \ | |
| .min_mV = min_mVolts, \ | |
| .max_mV = max_mVolts, \ | |
| .desc = { \ | |
| .name = #label, \ | |
| .id = TWL6030_REG_##label, \ | |
| .n_voltages = 32, \ | |
| .ops = &twl6030ldo_ops, \ | |
| .type = REGULATOR_VOLTAGE, \ | |
| .owner = THIS_MODULE, \ | |
| }, \ | |
| } | |
| #define TWL6032_ADJUSTABLE_LDO(label, offset, min_mVolts, max_mVolts) \ | |
| static const struct twlreg_info TWL6032_INFO_##label = { \ | |
| .base = offset, \ | |
| .min_mV = min_mVolts, \ | |
| .max_mV = max_mVolts, \ | |
| .desc = { \ | |
| .name = #label, \ | |
| .id = TWL6032_REG_##label, \ | |
| .n_voltages = 32, \ | |
| .ops = &twl6030ldo_ops, \ | |
| .type = REGULATOR_VOLTAGE, \ | |
| .owner = THIS_MODULE, \ | |
| }, \ | |
| } | |
| #define TWL_FIXED_LDO(label, offset, mVolts, num, turnon_delay, remap_conf, \ | |
| family, operations, map_mode) \ | |
| static const struct twlreg_info TWLFIXED_INFO_##label = { \ | |
| .base = offset, \ | |
| .id = num, \ | |
| .min_mV = mVolts, \ | |
| .remap = remap_conf, \ | |
| .desc = { \ | |
| .name = #label, \ | |
| .id = family##_REG_##label, \ | |
| .n_voltages = 1, \ | |
| .ops = &operations, \ | |
| .type = REGULATOR_VOLTAGE, \ | |
| .owner = THIS_MODULE, \ | |
| .min_uV = mVolts * 1000, \ | |
| .enable_time = turnon_delay, \ | |
| .of_map_mode = map_mode, \ | |
| }, \ | |
| } | |
| #define TWL6032_ADJUSTABLE_SMPS(label, offset) \ | |
| static const struct twlreg_info TWLSMPS_INFO_##label = { \ | |
| .base = offset, \ | |
| .min_mV = 600, \ | |
| .max_mV = 2100, \ | |
| .desc = { \ | |
| .name = #label, \ | |
| .id = TWL6032_REG_##label, \ | |
| .n_voltages = 63, \ | |
| .ops = &twlsmps_ops, \ | |
| .type = REGULATOR_VOLTAGE, \ | |
| .owner = THIS_MODULE, \ | |
| }, \ | |
| } | |
| /* | |
| * We list regulators here if systems need some level of | |
| * software control over them after boot. | |
| */ | |
| TWL4030_ADJUSTABLE_LDO(VAUX1, 0x17, 1, 100, 0x08); | |
| TWL4030_ADJUSTABLE_LDO(VAUX2_4030, 0x1b, 2, 100, 0x08); | |
| TWL4030_ADJUSTABLE_LDO(VAUX2, 0x1b, 2, 100, 0x08); | |
| TWL4030_ADJUSTABLE_LDO(VAUX3, 0x1f, 3, 100, 0x08); | |
| TWL4030_ADJUSTABLE_LDO(VAUX4, 0x23, 4, 100, 0x08); | |
| TWL4030_ADJUSTABLE_LDO(VMMC1, 0x27, 5, 100, 0x08); | |
| TWL4030_ADJUSTABLE_LDO(VMMC2, 0x2b, 6, 100, 0x08); | |
| TWL4030_ADJUSTABLE_LDO(VPLL1, 0x2f, 7, 100, 0x00); | |
| TWL4030_ADJUSTABLE_LDO(VPLL2, 0x33, 8, 100, 0x08); | |
| TWL4030_ADJUSTABLE_LDO(VSIM, 0x37, 9, 100, 0x00); | |
| TWL4030_ADJUSTABLE_LDO(VDAC, 0x3b, 10, 100, 0x08); | |
| TWL4030_ADJUSTABLE_LDO(VINTANA2, 0x43, 12, 100, 0x08); | |
| TWL4030_ADJUSTABLE_LDO(VIO, 0x4b, 14, 1000, 0x08); | |
| TWL4030_ADJUSTABLE_SMPS(VDD1, 0x55, 15, 1000, 0x08); | |
| TWL4030_ADJUSTABLE_SMPS(VDD2, 0x63, 16, 1000, 0x08); | |
| /* VUSBCP is managed *only* by the USB subchip */ | |
| /* 6030 REG with base as PMC Slave Misc : 0x0030 */ | |
| /* Turnon-delay and remap configuration values for 6030 are not | |
| verified since the specification is not public */ | |
| TWL6030_ADJUSTABLE_SMPS(VDD1); | |
| TWL6030_ADJUSTABLE_SMPS(VDD2); | |
| TWL6030_ADJUSTABLE_SMPS(VDD3); | |
| TWL6030_ADJUSTABLE_LDO(VAUX1_6030, 0x54, 1000, 3300); | |
| TWL6030_ADJUSTABLE_LDO(VAUX2_6030, 0x58, 1000, 3300); | |
| TWL6030_ADJUSTABLE_LDO(VAUX3_6030, 0x5c, 1000, 3300); | |
| TWL6030_ADJUSTABLE_LDO(VMMC, 0x68, 1000, 3300); | |
| TWL6030_ADJUSTABLE_LDO(VPP, 0x6c, 1000, 3300); | |
| TWL6030_ADJUSTABLE_LDO(VUSIM, 0x74, 1000, 3300); | |
| /* 6025 are renamed compared to 6030 versions */ | |
| TWL6032_ADJUSTABLE_LDO(LDO2, 0x54, 1000, 3300); | |
| TWL6032_ADJUSTABLE_LDO(LDO4, 0x58, 1000, 3300); | |
| TWL6032_ADJUSTABLE_LDO(LDO3, 0x5c, 1000, 3300); | |
| TWL6032_ADJUSTABLE_LDO(LDO5, 0x68, 1000, 3300); | |
| TWL6032_ADJUSTABLE_LDO(LDO1, 0x6c, 1000, 3300); | |
| TWL6032_ADJUSTABLE_LDO(LDO7, 0x74, 1000, 3300); | |
| TWL6032_ADJUSTABLE_LDO(LDO6, 0x60, 1000, 3300); | |
| TWL6032_ADJUSTABLE_LDO(LDOLN, 0x64, 1000, 3300); | |
| TWL6032_ADJUSTABLE_LDO(LDOUSB, 0x70, 1000, 3300); | |
| TWL4030_FIXED_LDO(VINTANA1, 0x3f, 1500, 11, 100, 0x08); | |
| TWL4030_FIXED_LDO(VINTDIG, 0x47, 1500, 13, 100, 0x08); | |
| TWL4030_FIXED_LDO(VUSB1V5, 0x71, 1500, 17, 100, 0x08); | |
| TWL4030_FIXED_LDO(VUSB1V8, 0x74, 1800, 18, 100, 0x08); | |
| TWL4030_FIXED_LDO(VUSB3V1, 0x77, 3100, 19, 150, 0x08); | |
| TWL6030_FIXED_LDO(VANA, 0x50, 2100, 0); | |
| TWL6030_FIXED_LDO(VCXIO, 0x60, 1800, 0); | |
| TWL6030_FIXED_LDO(VDAC, 0x64, 1800, 0); | |
| TWL6030_FIXED_LDO(VUSB, 0x70, 3300, 0); | |
| TWL6030_FIXED_LDO(V1V8, 0x16, 1800, 0); | |
| TWL6030_FIXED_LDO(V2V1, 0x1c, 2100, 0); | |
| TWL6032_ADJUSTABLE_SMPS(SMPS3, 0x34); | |
| TWL6032_ADJUSTABLE_SMPS(SMPS4, 0x10); | |
| TWL6032_ADJUSTABLE_SMPS(VIO, 0x16); | |
| static u8 twl_get_smps_offset(void) | |
| { | |
| u8 value; | |
| twl_i2c_read_u8(TWL_MODULE_PM_RECEIVER, &value, | |
| TWL6030_SMPS_OFFSET); | |
| return value; | |
| } | |
| static u8 twl_get_smps_mult(void) | |
| { | |
| u8 value; | |
| twl_i2c_read_u8(TWL_MODULE_PM_RECEIVER, &value, | |
| TWL6030_SMPS_MULT); | |
| return value; | |
| } | |
| #define TWL_OF_MATCH(comp, family, label) \ | |
| { \ | |
| .compatible = comp, \ | |
| .data = &family##_INFO_##label, \ | |
| } | |
| #define TWL4030_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL4030, label) | |
| #define TWL6030_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL6030, label) | |
| #define TWL6032_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWL6032, label) | |
| #define TWLFIXED_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLFIXED, label) | |
| #define TWLSMPS_OF_MATCH(comp, label) TWL_OF_MATCH(comp, TWLSMPS, label) | |
| static const struct of_device_id twl_of_match[] = { | |
| TWL4030_OF_MATCH("ti,twl4030-vaux1", VAUX1), | |
| TWL4030_OF_MATCH("ti,twl4030-vaux2", VAUX2_4030), | |
| TWL4030_OF_MATCH("ti,twl5030-vaux2", VAUX2), | |
| TWL4030_OF_MATCH("ti,twl4030-vaux3", VAUX3), | |
| TWL4030_OF_MATCH("ti,twl4030-vaux4", VAUX4), | |
| TWL4030_OF_MATCH("ti,twl4030-vmmc1", VMMC1), | |
| TWL4030_OF_MATCH("ti,twl4030-vmmc2", VMMC2), | |
| TWL4030_OF_MATCH("ti,twl4030-vpll1", VPLL1), | |
| TWL4030_OF_MATCH("ti,twl4030-vpll2", VPLL2), | |
| TWL4030_OF_MATCH("ti,twl4030-vsim", VSIM), | |
| TWL4030_OF_MATCH("ti,twl4030-vdac", VDAC), | |
| TWL4030_OF_MATCH("ti,twl4030-vintana2", VINTANA2), | |
| TWL4030_OF_MATCH("ti,twl4030-vio", VIO), | |
| TWL4030_OF_MATCH("ti,twl4030-vdd1", VDD1), | |
| TWL4030_OF_MATCH("ti,twl4030-vdd2", VDD2), | |
| TWL6030_OF_MATCH("ti,twl6030-vdd1", VDD1), | |
| TWL6030_OF_MATCH("ti,twl6030-vdd2", VDD2), | |
| TWL6030_OF_MATCH("ti,twl6030-vdd3", VDD3), | |
| TWL6030_OF_MATCH("ti,twl6030-vaux1", VAUX1_6030), | |
| TWL6030_OF_MATCH("ti,twl6030-vaux2", VAUX2_6030), | |
| TWL6030_OF_MATCH("ti,twl6030-vaux3", VAUX3_6030), | |
| TWL6030_OF_MATCH("ti,twl6030-vmmc", VMMC), | |
| TWL6030_OF_MATCH("ti,twl6030-vpp", VPP), | |
| TWL6030_OF_MATCH("ti,twl6030-vusim", VUSIM), | |
| TWL6032_OF_MATCH("ti,twl6032-ldo2", LDO2), | |
| TWL6032_OF_MATCH("ti,twl6032-ldo4", LDO4), | |
| TWL6032_OF_MATCH("ti,twl6032-ldo3", LDO3), | |
| TWL6032_OF_MATCH("ti,twl6032-ldo5", LDO5), | |
| TWL6032_OF_MATCH("ti,twl6032-ldo1", LDO1), | |
| TWL6032_OF_MATCH("ti,twl6032-ldo7", LDO7), | |
| TWL6032_OF_MATCH("ti,twl6032-ldo6", LDO6), | |
| TWL6032_OF_MATCH("ti,twl6032-ldoln", LDOLN), | |
| TWL6032_OF_MATCH("ti,twl6032-ldousb", LDOUSB), | |
| TWLFIXED_OF_MATCH("ti,twl4030-vintana1", VINTANA1), | |
| TWLFIXED_OF_MATCH("ti,twl4030-vintdig", VINTDIG), | |
| TWLFIXED_OF_MATCH("ti,twl4030-vusb1v5", VUSB1V5), | |
| TWLFIXED_OF_MATCH("ti,twl4030-vusb1v8", VUSB1V8), | |
| TWLFIXED_OF_MATCH("ti,twl4030-vusb3v1", VUSB3V1), | |
| TWLFIXED_OF_MATCH("ti,twl6030-vana", VANA), | |
| TWLFIXED_OF_MATCH("ti,twl6030-vcxio", VCXIO), | |
| TWLFIXED_OF_MATCH("ti,twl6030-vdac", VDAC), | |
| TWLFIXED_OF_MATCH("ti,twl6030-vusb", VUSB), | |
| TWLFIXED_OF_MATCH("ti,twl6030-v1v8", V1V8), | |
| TWLFIXED_OF_MATCH("ti,twl6030-v2v1", V2V1), | |
| TWLSMPS_OF_MATCH("ti,twl6032-smps3", SMPS3), | |
| TWLSMPS_OF_MATCH("ti,twl6032-smps4", SMPS4), | |
| TWLSMPS_OF_MATCH("ti,twl6032-vio", VIO), | |
| {}, | |
| }; | |
| MODULE_DEVICE_TABLE(of, twl_of_match); | |
| static int twlreg_probe(struct platform_device *pdev) | |
| { | |
| int i, id; | |
| struct twlreg_info *info; | |
| const struct twlreg_info *template; | |
| struct regulator_init_data *initdata; | |
| struct regulation_constraints *c; | |
| struct regulator_dev *rdev; | |
| struct twl_regulator_driver_data *drvdata; | |
| const struct of_device_id *match; | |
| struct regulator_config config = { }; | |
| match = of_match_device(twl_of_match, &pdev->dev); | |
| if (match) { | |
| template = match->data; | |
| id = template->desc.id; | |
| initdata = of_get_regulator_init_data(&pdev->dev, | |
| pdev->dev.of_node, | |
| &template->desc); | |
| drvdata = NULL; | |
| } else { | |
| id = pdev->id; | |
| initdata = dev_get_platdata(&pdev->dev); | |
| for (i = 0, template = NULL; i < ARRAY_SIZE(twl_of_match); i++) { | |
| template = twl_of_match[i].data; | |
| if (template && template->desc.id == id) | |
| break; | |
| } | |
| if (i == ARRAY_SIZE(twl_of_match)) | |
| return -ENODEV; | |
| drvdata = initdata->driver_data; | |
| if (!drvdata) | |
| return -EINVAL; | |
| } | |
| if (!template) | |
| return -ENODEV; | |
| if (!initdata) | |
| return -EINVAL; | |
| info = devm_kmemdup(&pdev->dev, template, sizeof(*info), GFP_KERNEL); | |
| if (!info) | |
| return -ENOMEM; | |
| if (drvdata) { | |
| /* copy the driver data into regulator data */ | |
| info->features = drvdata->features; | |
| info->data = drvdata->data; | |
| info->set_voltage = drvdata->set_voltage; | |
| info->get_voltage = drvdata->get_voltage; | |
| } | |
| /* Constrain board-specific capabilities according to what | |
| * this driver and the chip itself can actually do. | |
| */ | |
| c = &initdata->constraints; | |
| c->valid_modes_mask &= REGULATOR_MODE_NORMAL | REGULATOR_MODE_STANDBY; | |
| c->valid_ops_mask &= REGULATOR_CHANGE_VOLTAGE | |
| | REGULATOR_CHANGE_MODE | |
| | REGULATOR_CHANGE_STATUS; | |
| switch (id) { | |
| case TWL4030_REG_VIO: | |
| case TWL4030_REG_VDD1: | |
| case TWL4030_REG_VDD2: | |
| case TWL4030_REG_VPLL1: | |
| case TWL4030_REG_VINTANA1: | |
| case TWL4030_REG_VINTANA2: | |
| case TWL4030_REG_VINTDIG: | |
| c->always_on = true; | |
| break; | |
| default: | |
| break; | |
| } | |
| switch (id) { | |
| case TWL6032_REG_SMPS3: | |
| if (twl_get_smps_mult() & SMPS_MULTOFFSET_SMPS3) | |
| info->flags |= SMPS_EXTENDED_EN; | |
| if (twl_get_smps_offset() & SMPS_MULTOFFSET_SMPS3) | |
| info->flags |= SMPS_OFFSET_EN; | |
| break; | |
| case TWL6032_REG_SMPS4: | |
| if (twl_get_smps_mult() & SMPS_MULTOFFSET_SMPS4) | |
| info->flags |= SMPS_EXTENDED_EN; | |
| if (twl_get_smps_offset() & SMPS_MULTOFFSET_SMPS4) | |
| info->flags |= SMPS_OFFSET_EN; | |
| break; | |
| case TWL6032_REG_VIO: | |
| if (twl_get_smps_mult() & SMPS_MULTOFFSET_VIO) | |
| info->flags |= SMPS_EXTENDED_EN; | |
| if (twl_get_smps_offset() & SMPS_MULTOFFSET_VIO) | |
| info->flags |= SMPS_OFFSET_EN; | |
| break; | |
| } | |
| config.dev = &pdev->dev; | |
| config.init_data = initdata; | |
| config.driver_data = info; | |
| config.of_node = pdev->dev.of_node; | |
| rdev = devm_regulator_register(&pdev->dev, &info->desc, &config); | |
| if (IS_ERR(rdev)) { | |
| dev_err(&pdev->dev, "can't register %s, %ld\n", | |
| info->desc.name, PTR_ERR(rdev)); | |
| return PTR_ERR(rdev); | |
| } | |
| platform_set_drvdata(pdev, rdev); | |
| if (twl_class_is_4030()) | |
| twlreg_write(info, TWL_MODULE_PM_RECEIVER, VREG_REMAP, | |
| info->remap); | |
| /* NOTE: many regulators support short-circuit IRQs (presentable | |
| * as REGULATOR_OVER_CURRENT notifications?) configured via: | |
| * - SC_CONFIG | |
| * - SC_DETECT1 (vintana2, vmmc1/2, vaux1/2/3/4) | |
| * - SC_DETECT2 (vusb, vdac, vio, vdd1/2, vpll2) | |
| * - IT_CONFIG | |
| */ | |
| return 0; | |
| } | |
| MODULE_ALIAS("platform:twl_reg"); | |
| static struct platform_driver twlreg_driver = { | |
| .probe = twlreg_probe, | |
| /* NOTE: short name, to work around driver model truncation of | |
| * "twl_regulator.12" (and friends) to "twl_regulator.1". | |
| */ | |
| .driver = { | |
| .name = "twl_reg", | |
| .of_match_table = of_match_ptr(twl_of_match), | |
| }, | |
| }; | |
| static int __init twlreg_init(void) | |
| { | |
| return platform_driver_register(&twlreg_driver); | |
| } | |
| subsys_initcall(twlreg_init); | |
| static void __exit twlreg_exit(void) | |
| { | |
| platform_driver_unregister(&twlreg_driver); | |
| } | |
| module_exit(twlreg_exit) | |
| MODULE_DESCRIPTION("TWL regulator driver"); | |
| MODULE_LICENSE("GPL"); |