| /* | |
| * Copyright (C) 2010 Juergen Beisert, Pengutronix | |
| * | |
| * This code is based on: | |
| * Author: Vitaly Wool <vital@embeddedalley.com> | |
| * | |
| * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved. | |
| * Copyright 2008 Embedded Alley Solutions, Inc All Rights Reserved. | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License | |
| * as published by the Free Software Foundation; either version 2 | |
| * of the License, or (at your option) any later version. | |
| * This program is distributed in the hope that it will be useful, | |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| * GNU General Public License for more details. | |
| */ | |
| #define DRIVER_NAME "mxsfb" | |
| /** | |
| * @file | |
| * @brief LCDIF driver for i.MX23 and i.MX28 | |
| * | |
| * The LCDIF support four modes of operation | |
| * - MPU interface (to drive smart displays) -> not supported yet | |
| * - VSYNC interface (like MPU interface plus Vsync) -> not supported yet | |
| * - Dotclock interface (to drive LC displays with RGB data and sync signals) | |
| * - DVI (to drive ITU-R BT656) -> not supported yet | |
| * | |
| * This driver depends on a correct setup of the pins used for this purpose | |
| * (platform specific). | |
| * | |
| * For the developer: Don't forget to set the data bus width to the display | |
| * in the imx_fb_videomode structure. You will else end up with ugly colours. | |
| * If you fight against jitter you can vary the clock delay. This is a feature | |
| * of the i.MX28 and you can vary it between 2 ns ... 8 ns in 2 ns steps. Give | |
| * the required value in the imx_fb_videomode structure. | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/kernel.h> | |
| #include <linux/of_device.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/clk.h> | |
| #include <linux/dma-mapping.h> | |
| #include <linux/io.h> | |
| #include <linux/fb.h> | |
| #include <linux/regulator/consumer.h> | |
| #include <video/of_display_timing.h> | |
| #include <video/of_videomode.h> | |
| #include <video/videomode.h> | |
| #define REG_SET 4 | |
| #define REG_CLR 8 | |
| #define LCDC_CTRL 0x00 | |
| #define LCDC_CTRL1 0x10 | |
| #define LCDC_V4_CTRL2 0x20 | |
| #define LCDC_V3_TRANSFER_COUNT 0x20 | |
| #define LCDC_V4_TRANSFER_COUNT 0x30 | |
| #define LCDC_V4_CUR_BUF 0x40 | |
| #define LCDC_V4_NEXT_BUF 0x50 | |
| #define LCDC_V3_CUR_BUF 0x30 | |
| #define LCDC_V3_NEXT_BUF 0x40 | |
| #define LCDC_TIMING 0x60 | |
| #define LCDC_VDCTRL0 0x70 | |
| #define LCDC_VDCTRL1 0x80 | |
| #define LCDC_VDCTRL2 0x90 | |
| #define LCDC_VDCTRL3 0xa0 | |
| #define LCDC_VDCTRL4 0xb0 | |
| #define LCDC_DVICTRL0 0xc0 | |
| #define LCDC_DVICTRL1 0xd0 | |
| #define LCDC_DVICTRL2 0xe0 | |
| #define LCDC_DVICTRL3 0xf0 | |
| #define LCDC_DVICTRL4 0x100 | |
| #define LCDC_V4_DATA 0x180 | |
| #define LCDC_V3_DATA 0x1b0 | |
| #define LCDC_V4_DEBUG0 0x1d0 | |
| #define LCDC_V3_DEBUG0 0x1f0 | |
| #define CTRL_SFTRST (1 << 31) | |
| #define CTRL_CLKGATE (1 << 30) | |
| #define CTRL_BYPASS_COUNT (1 << 19) | |
| #define CTRL_VSYNC_MODE (1 << 18) | |
| #define CTRL_DOTCLK_MODE (1 << 17) | |
| #define CTRL_DATA_SELECT (1 << 16) | |
| #define CTRL_SET_BUS_WIDTH(x) (((x) & 0x3) << 10) | |
| #define CTRL_GET_BUS_WIDTH(x) (((x) >> 10) & 0x3) | |
| #define CTRL_SET_WORD_LENGTH(x) (((x) & 0x3) << 8) | |
| #define CTRL_GET_WORD_LENGTH(x) (((x) >> 8) & 0x3) | |
| #define CTRL_MASTER (1 << 5) | |
| #define CTRL_DF16 (1 << 3) | |
| #define CTRL_DF18 (1 << 2) | |
| #define CTRL_DF24 (1 << 1) | |
| #define CTRL_RUN (1 << 0) | |
| #define CTRL1_FIFO_CLEAR (1 << 21) | |
| #define CTRL1_SET_BYTE_PACKAGING(x) (((x) & 0xf) << 16) | |
| #define CTRL1_GET_BYTE_PACKAGING(x) (((x) >> 16) & 0xf) | |
| #define TRANSFER_COUNT_SET_VCOUNT(x) (((x) & 0xffff) << 16) | |
| #define TRANSFER_COUNT_GET_VCOUNT(x) (((x) >> 16) & 0xffff) | |
| #define TRANSFER_COUNT_SET_HCOUNT(x) ((x) & 0xffff) | |
| #define TRANSFER_COUNT_GET_HCOUNT(x) ((x) & 0xffff) | |
| #define VDCTRL0_ENABLE_PRESENT (1 << 28) | |
| #define VDCTRL0_VSYNC_ACT_HIGH (1 << 27) | |
| #define VDCTRL0_HSYNC_ACT_HIGH (1 << 26) | |
| #define VDCTRL0_DOTCLK_ACT_FALLING (1 << 25) | |
| #define VDCTRL0_ENABLE_ACT_HIGH (1 << 24) | |
| #define VDCTRL0_VSYNC_PERIOD_UNIT (1 << 21) | |
| #define VDCTRL0_VSYNC_PULSE_WIDTH_UNIT (1 << 20) | |
| #define VDCTRL0_HALF_LINE (1 << 19) | |
| #define VDCTRL0_HALF_LINE_MODE (1 << 18) | |
| #define VDCTRL0_SET_VSYNC_PULSE_WIDTH(x) ((x) & 0x3ffff) | |
| #define VDCTRL0_GET_VSYNC_PULSE_WIDTH(x) ((x) & 0x3ffff) | |
| #define VDCTRL2_SET_HSYNC_PERIOD(x) ((x) & 0x3ffff) | |
| #define VDCTRL2_GET_HSYNC_PERIOD(x) ((x) & 0x3ffff) | |
| #define VDCTRL3_MUX_SYNC_SIGNALS (1 << 29) | |
| #define VDCTRL3_VSYNC_ONLY (1 << 28) | |
| #define SET_HOR_WAIT_CNT(x) (((x) & 0xfff) << 16) | |
| #define GET_HOR_WAIT_CNT(x) (((x) >> 16) & 0xfff) | |
| #define SET_VERT_WAIT_CNT(x) ((x) & 0xffff) | |
| #define GET_VERT_WAIT_CNT(x) ((x) & 0xffff) | |
| #define VDCTRL4_SET_DOTCLK_DLY(x) (((x) & 0x7) << 29) /* v4 only */ | |
| #define VDCTRL4_GET_DOTCLK_DLY(x) (((x) >> 29) & 0x7) /* v4 only */ | |
| #define VDCTRL4_SYNC_SIGNALS_ON (1 << 18) | |
| #define SET_DOTCLK_H_VALID_DATA_CNT(x) ((x) & 0x3ffff) | |
| #define DEBUG0_HSYNC (1 < 26) | |
| #define DEBUG0_VSYNC (1 < 25) | |
| #define MIN_XRES 120 | |
| #define MIN_YRES 120 | |
| #define RED 0 | |
| #define GREEN 1 | |
| #define BLUE 2 | |
| #define TRANSP 3 | |
| #define STMLCDIF_8BIT 1 /** pixel data bus to the display is of 8 bit width */ | |
| #define STMLCDIF_16BIT 0 /** pixel data bus to the display is of 16 bit width */ | |
| #define STMLCDIF_18BIT 2 /** pixel data bus to the display is of 18 bit width */ | |
| #define STMLCDIF_24BIT 3 /** pixel data bus to the display is of 24 bit width */ | |
| #define MXSFB_SYNC_DATA_ENABLE_HIGH_ACT (1 << 6) | |
| #define MXSFB_SYNC_DOTCLK_FALLING_ACT (1 << 7) /* negtive edge sampling */ | |
| enum mxsfb_devtype { | |
| MXSFB_V3, | |
| MXSFB_V4, | |
| }; | |
| /* CPU dependent register offsets */ | |
| struct mxsfb_devdata { | |
| unsigned transfer_count; | |
| unsigned cur_buf; | |
| unsigned next_buf; | |
| unsigned debug0; | |
| unsigned hs_wdth_mask; | |
| unsigned hs_wdth_shift; | |
| unsigned ipversion; | |
| }; | |
| struct mxsfb_info { | |
| struct fb_info fb_info; | |
| struct platform_device *pdev; | |
| struct clk *clk; | |
| struct clk *clk_axi; | |
| struct clk *clk_disp_axi; | |
| void __iomem *base; /* registers */ | |
| unsigned allocated_size; | |
| int enabled; | |
| unsigned ld_intf_width; | |
| unsigned dotclk_delay; | |
| const struct mxsfb_devdata *devdata; | |
| u32 sync; | |
| struct regulator *reg_lcd; | |
| }; | |
| #define mxsfb_is_v3(host) (host->devdata->ipversion == 3) | |
| #define mxsfb_is_v4(host) (host->devdata->ipversion == 4) | |
| static const struct mxsfb_devdata mxsfb_devdata[] = { | |
| [MXSFB_V3] = { | |
| .transfer_count = LCDC_V3_TRANSFER_COUNT, | |
| .cur_buf = LCDC_V3_CUR_BUF, | |
| .next_buf = LCDC_V3_NEXT_BUF, | |
| .debug0 = LCDC_V3_DEBUG0, | |
| .hs_wdth_mask = 0xff, | |
| .hs_wdth_shift = 24, | |
| .ipversion = 3, | |
| }, | |
| [MXSFB_V4] = { | |
| .transfer_count = LCDC_V4_TRANSFER_COUNT, | |
| .cur_buf = LCDC_V4_CUR_BUF, | |
| .next_buf = LCDC_V4_NEXT_BUF, | |
| .debug0 = LCDC_V4_DEBUG0, | |
| .hs_wdth_mask = 0x3fff, | |
| .hs_wdth_shift = 18, | |
| .ipversion = 4, | |
| }, | |
| }; | |
| #define to_imxfb_host(x) (container_of(x, struct mxsfb_info, fb_info)) | |
| /* mask and shift depends on architecture */ | |
| static inline u32 set_hsync_pulse_width(struct mxsfb_info *host, unsigned val) | |
| { | |
| return (val & host->devdata->hs_wdth_mask) << | |
| host->devdata->hs_wdth_shift; | |
| } | |
| static inline u32 get_hsync_pulse_width(struct mxsfb_info *host, unsigned val) | |
| { | |
| return (val >> host->devdata->hs_wdth_shift) & | |
| host->devdata->hs_wdth_mask; | |
| } | |
| static const struct fb_bitfield def_rgb565[] = { | |
| [RED] = { | |
| .offset = 11, | |
| .length = 5, | |
| }, | |
| [GREEN] = { | |
| .offset = 5, | |
| .length = 6, | |
| }, | |
| [BLUE] = { | |
| .offset = 0, | |
| .length = 5, | |
| }, | |
| [TRANSP] = { /* no support for transparency */ | |
| .length = 0, | |
| } | |
| }; | |
| static const struct fb_bitfield def_rgb888[] = { | |
| [RED] = { | |
| .offset = 16, | |
| .length = 8, | |
| }, | |
| [GREEN] = { | |
| .offset = 8, | |
| .length = 8, | |
| }, | |
| [BLUE] = { | |
| .offset = 0, | |
| .length = 8, | |
| }, | |
| [TRANSP] = { /* no support for transparency */ | |
| .length = 0, | |
| } | |
| }; | |
| static inline unsigned chan_to_field(unsigned chan, struct fb_bitfield *bf) | |
| { | |
| chan &= 0xffff; | |
| chan >>= 16 - bf->length; | |
| return chan << bf->offset; | |
| } | |
| static int mxsfb_check_var(struct fb_var_screeninfo *var, | |
| struct fb_info *fb_info) | |
| { | |
| struct mxsfb_info *host = to_imxfb_host(fb_info); | |
| const struct fb_bitfield *rgb = NULL; | |
| if (var->xres < MIN_XRES) | |
| var->xres = MIN_XRES; | |
| if (var->yres < MIN_YRES) | |
| var->yres = MIN_YRES; | |
| var->xres_virtual = var->xres; | |
| var->yres_virtual = var->yres; | |
| switch (var->bits_per_pixel) { | |
| case 16: | |
| /* always expect RGB 565 */ | |
| rgb = def_rgb565; | |
| break; | |
| case 32: | |
| switch (host->ld_intf_width) { | |
| case STMLCDIF_8BIT: | |
| pr_debug("Unsupported LCD bus width mapping\n"); | |
| break; | |
| case STMLCDIF_16BIT: | |
| case STMLCDIF_18BIT: | |
| case STMLCDIF_24BIT: | |
| /* real 24 bit */ | |
| rgb = def_rgb888; | |
| break; | |
| } | |
| break; | |
| default: | |
| pr_err("Unsupported colour depth: %u\n", var->bits_per_pixel); | |
| return -EINVAL; | |
| } | |
| /* | |
| * Copy the RGB parameters for this display | |
| * from the machine specific parameters. | |
| */ | |
| var->red = rgb[RED]; | |
| var->green = rgb[GREEN]; | |
| var->blue = rgb[BLUE]; | |
| var->transp = rgb[TRANSP]; | |
| return 0; | |
| } | |
| static inline void mxsfb_enable_axi_clk(struct mxsfb_info *host) | |
| { | |
| if (host->clk_axi) | |
| clk_prepare_enable(host->clk_axi); | |
| } | |
| static inline void mxsfb_disable_axi_clk(struct mxsfb_info *host) | |
| { | |
| if (host->clk_axi) | |
| clk_disable_unprepare(host->clk_axi); | |
| } | |
| static void mxsfb_enable_controller(struct fb_info *fb_info) | |
| { | |
| struct mxsfb_info *host = to_imxfb_host(fb_info); | |
| u32 reg; | |
| int ret; | |
| dev_dbg(&host->pdev->dev, "%s\n", __func__); | |
| if (host->reg_lcd) { | |
| ret = regulator_enable(host->reg_lcd); | |
| if (ret) { | |
| dev_err(&host->pdev->dev, | |
| "lcd regulator enable failed: %d\n", ret); | |
| return; | |
| } | |
| } | |
| if (host->clk_disp_axi) | |
| clk_prepare_enable(host->clk_disp_axi); | |
| clk_prepare_enable(host->clk); | |
| clk_set_rate(host->clk, PICOS2KHZ(fb_info->var.pixclock) * 1000U); | |
| mxsfb_enable_axi_clk(host); | |
| /* if it was disabled, re-enable the mode again */ | |
| writel(CTRL_DOTCLK_MODE, host->base + LCDC_CTRL + REG_SET); | |
| /* enable the SYNC signals first, then the DMA engine */ | |
| reg = readl(host->base + LCDC_VDCTRL4); | |
| reg |= VDCTRL4_SYNC_SIGNALS_ON; | |
| writel(reg, host->base + LCDC_VDCTRL4); | |
| writel(CTRL_RUN, host->base + LCDC_CTRL + REG_SET); | |
| host->enabled = 1; | |
| } | |
| static void mxsfb_disable_controller(struct fb_info *fb_info) | |
| { | |
| struct mxsfb_info *host = to_imxfb_host(fb_info); | |
| unsigned loop; | |
| u32 reg; | |
| int ret; | |
| dev_dbg(&host->pdev->dev, "%s\n", __func__); | |
| /* | |
| * Even if we disable the controller here, it will still continue | |
| * until its FIFOs are running out of data | |
| */ | |
| writel(CTRL_DOTCLK_MODE, host->base + LCDC_CTRL + REG_CLR); | |
| loop = 1000; | |
| while (loop) { | |
| reg = readl(host->base + LCDC_CTRL); | |
| if (!(reg & CTRL_RUN)) | |
| break; | |
| loop--; | |
| } | |
| reg = readl(host->base + LCDC_VDCTRL4); | |
| writel(reg & ~VDCTRL4_SYNC_SIGNALS_ON, host->base + LCDC_VDCTRL4); | |
| mxsfb_disable_axi_clk(host); | |
| clk_disable_unprepare(host->clk); | |
| if (host->clk_disp_axi) | |
| clk_disable_unprepare(host->clk_disp_axi); | |
| host->enabled = 0; | |
| if (host->reg_lcd) { | |
| ret = regulator_disable(host->reg_lcd); | |
| if (ret) | |
| dev_err(&host->pdev->dev, | |
| "lcd regulator disable failed: %d\n", ret); | |
| } | |
| } | |
| static int mxsfb_set_par(struct fb_info *fb_info) | |
| { | |
| struct mxsfb_info *host = to_imxfb_host(fb_info); | |
| u32 ctrl, vdctrl0, vdctrl4; | |
| int line_size, fb_size; | |
| int reenable = 0; | |
| line_size = fb_info->var.xres * (fb_info->var.bits_per_pixel >> 3); | |
| fb_size = fb_info->var.yres_virtual * line_size; | |
| if (fb_size > fb_info->fix.smem_len) | |
| return -ENOMEM; | |
| fb_info->fix.line_length = line_size; | |
| /* | |
| * It seems, you can't re-program the controller if it is still running. | |
| * This may lead into shifted pictures (FIFO issue?). | |
| * So, first stop the controller and drain its FIFOs | |
| */ | |
| if (host->enabled) { | |
| reenable = 1; | |
| mxsfb_disable_controller(fb_info); | |
| } | |
| mxsfb_enable_axi_clk(host); | |
| /* clear the FIFOs */ | |
| writel(CTRL1_FIFO_CLEAR, host->base + LCDC_CTRL1 + REG_SET); | |
| ctrl = CTRL_BYPASS_COUNT | CTRL_MASTER | | |
| CTRL_SET_BUS_WIDTH(host->ld_intf_width); | |
| switch (fb_info->var.bits_per_pixel) { | |
| case 16: | |
| dev_dbg(&host->pdev->dev, "Setting up RGB565 mode\n"); | |
| ctrl |= CTRL_SET_WORD_LENGTH(0); | |
| writel(CTRL1_SET_BYTE_PACKAGING(0xf), host->base + LCDC_CTRL1); | |
| break; | |
| case 32: | |
| dev_dbg(&host->pdev->dev, "Setting up RGB888/666 mode\n"); | |
| ctrl |= CTRL_SET_WORD_LENGTH(3); | |
| switch (host->ld_intf_width) { | |
| case STMLCDIF_8BIT: | |
| mxsfb_disable_axi_clk(host); | |
| dev_err(&host->pdev->dev, | |
| "Unsupported LCD bus width mapping\n"); | |
| return -EINVAL; | |
| case STMLCDIF_16BIT: | |
| case STMLCDIF_18BIT: | |
| case STMLCDIF_24BIT: | |
| /* real 24 bit */ | |
| break; | |
| } | |
| /* do not use packed pixels = one pixel per word instead */ | |
| writel(CTRL1_SET_BYTE_PACKAGING(0x7), host->base + LCDC_CTRL1); | |
| break; | |
| default: | |
| mxsfb_disable_axi_clk(host); | |
| dev_err(&host->pdev->dev, "Unhandled color depth of %u\n", | |
| fb_info->var.bits_per_pixel); | |
| return -EINVAL; | |
| } | |
| writel(ctrl, host->base + LCDC_CTRL); | |
| writel(TRANSFER_COUNT_SET_VCOUNT(fb_info->var.yres) | | |
| TRANSFER_COUNT_SET_HCOUNT(fb_info->var.xres), | |
| host->base + host->devdata->transfer_count); | |
| vdctrl0 = VDCTRL0_ENABLE_PRESENT | /* always in DOTCLOCK mode */ | |
| VDCTRL0_VSYNC_PERIOD_UNIT | | |
| VDCTRL0_VSYNC_PULSE_WIDTH_UNIT | | |
| VDCTRL0_SET_VSYNC_PULSE_WIDTH(fb_info->var.vsync_len); | |
| if (fb_info->var.sync & FB_SYNC_HOR_HIGH_ACT) | |
| vdctrl0 |= VDCTRL0_HSYNC_ACT_HIGH; | |
| if (fb_info->var.sync & FB_SYNC_VERT_HIGH_ACT) | |
| vdctrl0 |= VDCTRL0_VSYNC_ACT_HIGH; | |
| if (host->sync & MXSFB_SYNC_DATA_ENABLE_HIGH_ACT) | |
| vdctrl0 |= VDCTRL0_ENABLE_ACT_HIGH; | |
| if (host->sync & MXSFB_SYNC_DOTCLK_FALLING_ACT) | |
| vdctrl0 |= VDCTRL0_DOTCLK_ACT_FALLING; | |
| writel(vdctrl0, host->base + LCDC_VDCTRL0); | |
| /* frame length in lines */ | |
| writel(fb_info->var.upper_margin + fb_info->var.vsync_len + | |
| fb_info->var.lower_margin + fb_info->var.yres, | |
| host->base + LCDC_VDCTRL1); | |
| /* line length in units of clocks or pixels */ | |
| writel(set_hsync_pulse_width(host, fb_info->var.hsync_len) | | |
| VDCTRL2_SET_HSYNC_PERIOD(fb_info->var.left_margin + | |
| fb_info->var.hsync_len + fb_info->var.right_margin + | |
| fb_info->var.xres), | |
| host->base + LCDC_VDCTRL2); | |
| writel(SET_HOR_WAIT_CNT(fb_info->var.left_margin + | |
| fb_info->var.hsync_len) | | |
| SET_VERT_WAIT_CNT(fb_info->var.upper_margin + | |
| fb_info->var.vsync_len), | |
| host->base + LCDC_VDCTRL3); | |
| vdctrl4 = SET_DOTCLK_H_VALID_DATA_CNT(fb_info->var.xres); | |
| if (mxsfb_is_v4(host)) | |
| vdctrl4 |= VDCTRL4_SET_DOTCLK_DLY(host->dotclk_delay); | |
| writel(vdctrl4, host->base + LCDC_VDCTRL4); | |
| writel(fb_info->fix.smem_start + | |
| fb_info->fix.line_length * fb_info->var.yoffset, | |
| host->base + host->devdata->next_buf); | |
| mxsfb_disable_axi_clk(host); | |
| if (reenable) | |
| mxsfb_enable_controller(fb_info); | |
| return 0; | |
| } | |
| static int mxsfb_setcolreg(u_int regno, u_int red, u_int green, u_int blue, | |
| u_int transp, struct fb_info *fb_info) | |
| { | |
| unsigned int val; | |
| int ret = -EINVAL; | |
| /* | |
| * If greyscale is true, then we convert the RGB value | |
| * to greyscale no matter what visual we are using. | |
| */ | |
| if (fb_info->var.grayscale) | |
| red = green = blue = (19595 * red + 38470 * green + | |
| 7471 * blue) >> 16; | |
| switch (fb_info->fix.visual) { | |
| case FB_VISUAL_TRUECOLOR: | |
| /* | |
| * 12 or 16-bit True Colour. We encode the RGB value | |
| * according to the RGB bitfield information. | |
| */ | |
| if (regno < 16) { | |
| u32 *pal = fb_info->pseudo_palette; | |
| val = chan_to_field(red, &fb_info->var.red); | |
| val |= chan_to_field(green, &fb_info->var.green); | |
| val |= chan_to_field(blue, &fb_info->var.blue); | |
| pal[regno] = val; | |
| ret = 0; | |
| } | |
| break; | |
| case FB_VISUAL_STATIC_PSEUDOCOLOR: | |
| case FB_VISUAL_PSEUDOCOLOR: | |
| break; | |
| } | |
| return ret; | |
| } | |
| static int mxsfb_blank(int blank, struct fb_info *fb_info) | |
| { | |
| struct mxsfb_info *host = to_imxfb_host(fb_info); | |
| switch (blank) { | |
| case FB_BLANK_POWERDOWN: | |
| case FB_BLANK_VSYNC_SUSPEND: | |
| case FB_BLANK_HSYNC_SUSPEND: | |
| case FB_BLANK_NORMAL: | |
| if (host->enabled) | |
| mxsfb_disable_controller(fb_info); | |
| break; | |
| case FB_BLANK_UNBLANK: | |
| if (!host->enabled) | |
| mxsfb_enable_controller(fb_info); | |
| break; | |
| } | |
| return 0; | |
| } | |
| static int mxsfb_pan_display(struct fb_var_screeninfo *var, | |
| struct fb_info *fb_info) | |
| { | |
| struct mxsfb_info *host = to_imxfb_host(fb_info); | |
| unsigned offset; | |
| if (var->xoffset != 0) | |
| return -EINVAL; | |
| offset = fb_info->fix.line_length * var->yoffset; | |
| mxsfb_enable_axi_clk(host); | |
| /* update on next VSYNC */ | |
| writel(fb_info->fix.smem_start + offset, | |
| host->base + host->devdata->next_buf); | |
| mxsfb_disable_axi_clk(host); | |
| return 0; | |
| } | |
| static struct fb_ops mxsfb_ops = { | |
| .owner = THIS_MODULE, | |
| .fb_check_var = mxsfb_check_var, | |
| .fb_set_par = mxsfb_set_par, | |
| .fb_setcolreg = mxsfb_setcolreg, | |
| .fb_blank = mxsfb_blank, | |
| .fb_pan_display = mxsfb_pan_display, | |
| .fb_fillrect = cfb_fillrect, | |
| .fb_copyarea = cfb_copyarea, | |
| .fb_imageblit = cfb_imageblit, | |
| }; | |
| static int mxsfb_restore_mode(struct mxsfb_info *host, | |
| struct fb_videomode *vmode) | |
| { | |
| struct fb_info *fb_info = &host->fb_info; | |
| unsigned line_count; | |
| unsigned period; | |
| unsigned long pa, fbsize; | |
| int bits_per_pixel, ofs, ret = 0; | |
| u32 transfer_count, vdctrl0, vdctrl2, vdctrl3, vdctrl4, ctrl; | |
| mxsfb_enable_axi_clk(host); | |
| /* Only restore the mode when the controller is running */ | |
| ctrl = readl(host->base + LCDC_CTRL); | |
| if (!(ctrl & CTRL_RUN)) { | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| vdctrl0 = readl(host->base + LCDC_VDCTRL0); | |
| vdctrl2 = readl(host->base + LCDC_VDCTRL2); | |
| vdctrl3 = readl(host->base + LCDC_VDCTRL3); | |
| vdctrl4 = readl(host->base + LCDC_VDCTRL4); | |
| transfer_count = readl(host->base + host->devdata->transfer_count); | |
| vmode->xres = TRANSFER_COUNT_GET_HCOUNT(transfer_count); | |
| vmode->yres = TRANSFER_COUNT_GET_VCOUNT(transfer_count); | |
| switch (CTRL_GET_WORD_LENGTH(ctrl)) { | |
| case 0: | |
| bits_per_pixel = 16; | |
| break; | |
| case 3: | |
| bits_per_pixel = 32; | |
| break; | |
| case 1: | |
| default: | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| fb_info->var.bits_per_pixel = bits_per_pixel; | |
| vmode->pixclock = KHZ2PICOS(clk_get_rate(host->clk) / 1000U); | |
| vmode->hsync_len = get_hsync_pulse_width(host, vdctrl2); | |
| vmode->left_margin = GET_HOR_WAIT_CNT(vdctrl3) - vmode->hsync_len; | |
| vmode->right_margin = VDCTRL2_GET_HSYNC_PERIOD(vdctrl2) - | |
| vmode->hsync_len - vmode->left_margin - vmode->xres; | |
| vmode->vsync_len = VDCTRL0_GET_VSYNC_PULSE_WIDTH(vdctrl0); | |
| period = readl(host->base + LCDC_VDCTRL1); | |
| vmode->upper_margin = GET_VERT_WAIT_CNT(vdctrl3) - vmode->vsync_len; | |
| vmode->lower_margin = period - vmode->vsync_len - | |
| vmode->upper_margin - vmode->yres; | |
| vmode->vmode = FB_VMODE_NONINTERLACED; | |
| vmode->sync = 0; | |
| if (vdctrl0 & VDCTRL0_HSYNC_ACT_HIGH) | |
| vmode->sync |= FB_SYNC_HOR_HIGH_ACT; | |
| if (vdctrl0 & VDCTRL0_VSYNC_ACT_HIGH) | |
| vmode->sync |= FB_SYNC_VERT_HIGH_ACT; | |
| pr_debug("Reconstructed video mode:\n"); | |
| pr_debug("%dx%d, hsync: %u left: %u, right: %u, vsync: %u, upper: %u, lower: %u\n", | |
| vmode->xres, vmode->yres, vmode->hsync_len, vmode->left_margin, | |
| vmode->right_margin, vmode->vsync_len, vmode->upper_margin, | |
| vmode->lower_margin); | |
| pr_debug("pixclk: %ldkHz\n", PICOS2KHZ(vmode->pixclock)); | |
| host->ld_intf_width = CTRL_GET_BUS_WIDTH(ctrl); | |
| host->dotclk_delay = VDCTRL4_GET_DOTCLK_DLY(vdctrl4); | |
| fb_info->fix.line_length = vmode->xres * (bits_per_pixel >> 3); | |
| pa = readl(host->base + host->devdata->cur_buf); | |
| fbsize = fb_info->fix.line_length * vmode->yres; | |
| if (pa < fb_info->fix.smem_start) { | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| if (pa + fbsize > fb_info->fix.smem_start + fb_info->fix.smem_len) { | |
| ret = -EINVAL; | |
| goto err; | |
| } | |
| ofs = pa - fb_info->fix.smem_start; | |
| if (ofs) { | |
| memmove(fb_info->screen_base, fb_info->screen_base + ofs, fbsize); | |
| writel(fb_info->fix.smem_start, host->base + host->devdata->next_buf); | |
| } | |
| line_count = fb_info->fix.smem_len / fb_info->fix.line_length; | |
| fb_info->fix.ypanstep = 1; | |
| clk_prepare_enable(host->clk); | |
| host->enabled = 1; | |
| err: | |
| if (ret) | |
| mxsfb_disable_axi_clk(host); | |
| return ret; | |
| } | |
| static int mxsfb_init_fbinfo_dt(struct mxsfb_info *host, | |
| struct fb_videomode *vmode) | |
| { | |
| struct fb_info *fb_info = &host->fb_info; | |
| struct fb_var_screeninfo *var = &fb_info->var; | |
| struct device *dev = &host->pdev->dev; | |
| struct device_node *np = host->pdev->dev.of_node; | |
| struct device_node *display_np; | |
| struct videomode vm; | |
| u32 width; | |
| int ret; | |
| display_np = of_parse_phandle(np, "display", 0); | |
| if (!display_np) { | |
| dev_err(dev, "failed to find display phandle\n"); | |
| return -ENOENT; | |
| } | |
| ret = of_property_read_u32(display_np, "bus-width", &width); | |
| if (ret < 0) { | |
| dev_err(dev, "failed to get property bus-width\n"); | |
| goto put_display_node; | |
| } | |
| switch (width) { | |
| case 8: | |
| host->ld_intf_width = STMLCDIF_8BIT; | |
| break; | |
| case 16: | |
| host->ld_intf_width = STMLCDIF_16BIT; | |
| break; | |
| case 18: | |
| host->ld_intf_width = STMLCDIF_18BIT; | |
| break; | |
| case 24: | |
| host->ld_intf_width = STMLCDIF_24BIT; | |
| break; | |
| default: | |
| dev_err(dev, "invalid bus-width value\n"); | |
| ret = -EINVAL; | |
| goto put_display_node; | |
| } | |
| ret = of_property_read_u32(display_np, "bits-per-pixel", | |
| &var->bits_per_pixel); | |
| if (ret < 0) { | |
| dev_err(dev, "failed to get property bits-per-pixel\n"); | |
| goto put_display_node; | |
| } | |
| ret = of_get_videomode(display_np, &vm, OF_USE_NATIVE_MODE); | |
| if (ret) { | |
| dev_err(dev, "failed to get videomode from DT\n"); | |
| goto put_display_node; | |
| } | |
| ret = fb_videomode_from_videomode(&vm, vmode); | |
| if (ret < 0) | |
| goto put_display_node; | |
| if (vm.flags & DISPLAY_FLAGS_DE_HIGH) | |
| host->sync |= MXSFB_SYNC_DATA_ENABLE_HIGH_ACT; | |
| if (vm.flags & DISPLAY_FLAGS_PIXDATA_NEGEDGE) | |
| host->sync |= MXSFB_SYNC_DOTCLK_FALLING_ACT; | |
| put_display_node: | |
| of_node_put(display_np); | |
| return ret; | |
| } | |
| static int mxsfb_init_fbinfo(struct mxsfb_info *host, | |
| struct fb_videomode *vmode) | |
| { | |
| int ret; | |
| struct device *dev = &host->pdev->dev; | |
| struct fb_info *fb_info = &host->fb_info; | |
| struct fb_var_screeninfo *var = &fb_info->var; | |
| dma_addr_t fb_phys; | |
| void *fb_virt; | |
| unsigned fb_size; | |
| fb_info->fbops = &mxsfb_ops; | |
| fb_info->flags = FBINFO_FLAG_DEFAULT | FBINFO_READS_FAST; | |
| strlcpy(fb_info->fix.id, "mxs", sizeof(fb_info->fix.id)); | |
| fb_info->fix.type = FB_TYPE_PACKED_PIXELS; | |
| fb_info->fix.ypanstep = 1; | |
| fb_info->fix.visual = FB_VISUAL_TRUECOLOR, | |
| fb_info->fix.accel = FB_ACCEL_NONE; | |
| ret = mxsfb_init_fbinfo_dt(host, vmode); | |
| if (ret) | |
| return ret; | |
| var->nonstd = 0; | |
| var->activate = FB_ACTIVATE_NOW; | |
| var->accel_flags = 0; | |
| var->vmode = FB_VMODE_NONINTERLACED; | |
| /* Memory allocation for framebuffer */ | |
| fb_size = SZ_2M; | |
| fb_virt = dma_alloc_wc(dev, PAGE_ALIGN(fb_size), &fb_phys, GFP_KERNEL); | |
| if (!fb_virt) | |
| return -ENOMEM; | |
| fb_info->fix.smem_start = fb_phys; | |
| fb_info->screen_base = fb_virt; | |
| fb_info->screen_size = fb_info->fix.smem_len = fb_size; | |
| if (mxsfb_restore_mode(host, vmode)) | |
| memset(fb_virt, 0, fb_size); | |
| return 0; | |
| } | |
| static void mxsfb_free_videomem(struct mxsfb_info *host) | |
| { | |
| struct device *dev = &host->pdev->dev; | |
| struct fb_info *fb_info = &host->fb_info; | |
| dma_free_wc(dev, fb_info->screen_size, fb_info->screen_base, | |
| fb_info->fix.smem_start); | |
| } | |
| static const struct platform_device_id mxsfb_devtype[] = { | |
| { | |
| .name = "imx23-fb", | |
| .driver_data = MXSFB_V3, | |
| }, { | |
| .name = "imx28-fb", | |
| .driver_data = MXSFB_V4, | |
| }, { | |
| /* sentinel */ | |
| } | |
| }; | |
| MODULE_DEVICE_TABLE(platform, mxsfb_devtype); | |
| static const struct of_device_id mxsfb_dt_ids[] = { | |
| { .compatible = "fsl,imx23-lcdif", .data = &mxsfb_devtype[0], }, | |
| { .compatible = "fsl,imx28-lcdif", .data = &mxsfb_devtype[1], }, | |
| { /* sentinel */ } | |
| }; | |
| MODULE_DEVICE_TABLE(of, mxsfb_dt_ids); | |
| static int mxsfb_probe(struct platform_device *pdev) | |
| { | |
| const struct of_device_id *of_id = | |
| of_match_device(mxsfb_dt_ids, &pdev->dev); | |
| struct resource *res; | |
| struct mxsfb_info *host; | |
| struct fb_info *fb_info; | |
| struct fb_videomode *mode; | |
| int ret; | |
| if (of_id) | |
| pdev->id_entry = of_id->data; | |
| fb_info = framebuffer_alloc(sizeof(struct mxsfb_info), &pdev->dev); | |
| if (!fb_info) { | |
| dev_err(&pdev->dev, "Failed to allocate fbdev\n"); | |
| return -ENOMEM; | |
| } | |
| mode = devm_kzalloc(&pdev->dev, sizeof(struct fb_videomode), | |
| GFP_KERNEL); | |
| if (mode == NULL) | |
| return -ENOMEM; | |
| host = to_imxfb_host(fb_info); | |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
| host->base = devm_ioremap_resource(&pdev->dev, res); | |
| if (IS_ERR(host->base)) { | |
| ret = PTR_ERR(host->base); | |
| goto fb_release; | |
| } | |
| host->pdev = pdev; | |
| platform_set_drvdata(pdev, host); | |
| host->devdata = &mxsfb_devdata[pdev->id_entry->driver_data]; | |
| host->clk = devm_clk_get(&host->pdev->dev, NULL); | |
| if (IS_ERR(host->clk)) { | |
| ret = PTR_ERR(host->clk); | |
| goto fb_release; | |
| } | |
| host->clk_axi = devm_clk_get(&host->pdev->dev, "axi"); | |
| if (IS_ERR(host->clk_axi)) | |
| host->clk_axi = NULL; | |
| host->clk_disp_axi = devm_clk_get(&host->pdev->dev, "disp_axi"); | |
| if (IS_ERR(host->clk_disp_axi)) | |
| host->clk_disp_axi = NULL; | |
| host->reg_lcd = devm_regulator_get(&pdev->dev, "lcd"); | |
| if (IS_ERR(host->reg_lcd)) | |
| host->reg_lcd = NULL; | |
| fb_info->pseudo_palette = devm_kzalloc(&pdev->dev, sizeof(u32) * 16, | |
| GFP_KERNEL); | |
| if (!fb_info->pseudo_palette) { | |
| ret = -ENOMEM; | |
| goto fb_release; | |
| } | |
| ret = mxsfb_init_fbinfo(host, mode); | |
| if (ret != 0) | |
| goto fb_release; | |
| fb_videomode_to_var(&fb_info->var, mode); | |
| /* init the color fields */ | |
| mxsfb_check_var(&fb_info->var, fb_info); | |
| platform_set_drvdata(pdev, fb_info); | |
| ret = register_framebuffer(fb_info); | |
| if (ret != 0) { | |
| dev_err(&pdev->dev,"Failed to register framebuffer\n"); | |
| goto fb_destroy; | |
| } | |
| if (!host->enabled) { | |
| mxsfb_enable_axi_clk(host); | |
| writel(0, host->base + LCDC_CTRL); | |
| mxsfb_disable_axi_clk(host); | |
| mxsfb_set_par(fb_info); | |
| mxsfb_enable_controller(fb_info); | |
| } | |
| dev_info(&pdev->dev, "initialized\n"); | |
| return 0; | |
| fb_destroy: | |
| if (host->enabled) | |
| clk_disable_unprepare(host->clk); | |
| fb_release: | |
| framebuffer_release(fb_info); | |
| return ret; | |
| } | |
| static int mxsfb_remove(struct platform_device *pdev) | |
| { | |
| struct fb_info *fb_info = platform_get_drvdata(pdev); | |
| struct mxsfb_info *host = to_imxfb_host(fb_info); | |
| if (host->enabled) | |
| mxsfb_disable_controller(fb_info); | |
| unregister_framebuffer(fb_info); | |
| mxsfb_free_videomem(host); | |
| framebuffer_release(fb_info); | |
| return 0; | |
| } | |
| static void mxsfb_shutdown(struct platform_device *pdev) | |
| { | |
| struct fb_info *fb_info = platform_get_drvdata(pdev); | |
| struct mxsfb_info *host = to_imxfb_host(fb_info); | |
| mxsfb_enable_axi_clk(host); | |
| /* | |
| * Force stop the LCD controller as keeping it running during reboot | |
| * might interfere with the BootROM's boot mode pads sampling. | |
| */ | |
| writel(CTRL_RUN, host->base + LCDC_CTRL + REG_CLR); | |
| mxsfb_disable_axi_clk(host); | |
| } | |
| static struct platform_driver mxsfb_driver = { | |
| .probe = mxsfb_probe, | |
| .remove = mxsfb_remove, | |
| .shutdown = mxsfb_shutdown, | |
| .id_table = mxsfb_devtype, | |
| .driver = { | |
| .name = DRIVER_NAME, | |
| .of_match_table = mxsfb_dt_ids, | |
| }, | |
| }; | |
| module_platform_driver(mxsfb_driver); | |
| MODULE_DESCRIPTION("Freescale mxs framebuffer driver"); | |
| MODULE_AUTHOR("Sascha Hauer, Pengutronix"); | |
| MODULE_LICENSE("GPL"); |