| /* |
| * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| */ |
| |
| #ifndef _UFS_QUIRKS_H_ |
| #define _UFS_QUIRKS_H_ |
| |
| /* return true if s1 is a prefix of s2 */ |
| #define STR_PRFX_EQUAL(s1, s2) !strncmp(s1, s2, strlen(s1)) |
| |
| #define UFS_ANY_VENDOR 0xFFFF |
| #define UFS_ANY_MODEL "ANY_MODEL" |
| |
| #define MAX_MODEL_LEN 16 |
| |
| #define UFS_VENDOR_TOSHIBA 0x198 |
| #define UFS_VENDOR_SAMSUNG 0x1CE |
| #define UFS_VENDOR_SKHYNIX 0x1AD |
| |
| /** |
| * ufs_device_info - ufs device details |
| * @wmanufacturerid: card details |
| * @model: card model |
| */ |
| struct ufs_device_info { |
| u16 wmanufacturerid; |
| char model[MAX_MODEL_LEN + 1]; |
| }; |
| |
| /** |
| * ufs_dev_fix - ufs device quirk info |
| * @card: ufs card details |
| * @quirk: device quirk |
| */ |
| struct ufs_dev_fix { |
| struct ufs_device_info card; |
| unsigned int quirk; |
| }; |
| |
| #define END_FIX { { 0 }, 0 } |
| |
| /* add specific device quirk */ |
| #define UFS_FIX(_vendor, _model, _quirk) \ |
| { \ |
| .card.wmanufacturerid = (_vendor),\ |
| .card.model = (_model), \ |
| .quirk = (_quirk), \ |
| } |
| |
| /* |
| * If UFS device is having issue in processing LCC (Line Control |
| * Command) coming from UFS host controller then enable this quirk. |
| * When this quirk is enabled, host controller driver should disable |
| * the LCC transmission on UFS host controller (by clearing |
| * TX_LCC_ENABLE attribute of host to 0). |
| */ |
| #define UFS_DEVICE_QUIRK_BROKEN_LCC (1 << 0) |
| |
| /* |
| * Some UFS devices don't need VCCQ rail for device operations. Enabling this |
| * quirk for such devices will make sure that VCCQ rail is not voted. |
| */ |
| #define UFS_DEVICE_NO_VCCQ (1 << 1) |
| |
| /* |
| * Some vendor's UFS device sends back to back NACs for the DL data frames |
| * causing the host controller to raise the DFES error status. Sometimes |
| * such UFS devices send back to back NAC without waiting for new |
| * retransmitted DL frame from the host and in such cases it might be possible |
| * the Host UniPro goes into bad state without raising the DFES error |
| * interrupt. If this happens then all the pending commands would timeout |
| * only after respective SW command (which is generally too large). |
| * |
| * We can workaround such device behaviour like this: |
| * - As soon as SW sees the DL NAC error, it should schedule the error handler |
| * - Error handler would sleep for 50ms to see if there are any fatal errors |
| * raised by UFS controller. |
| * - If there are fatal errors then SW does normal error recovery. |
| * - If there are no fatal errors then SW sends the NOP command to device |
| * to check if link is alive. |
| * - If NOP command times out, SW does normal error recovery |
| * - If NOP command succeed, skip the error handling. |
| * |
| * If DL NAC error is seen multiple times with some vendor's UFS devices then |
| * enable this quirk to initiate quick error recovery and also silence related |
| * error logs to reduce spamming of kernel logs. |
| */ |
| #define UFS_DEVICE_QUIRK_RECOVERY_FROM_DL_NAC_ERRORS (1 << 2) |
| |
| /* |
| * Some UFS devices may not work properly after resume if the link was kept |
| * in off state during suspend. Enabling this quirk will not allow the |
| * link to be kept in off state during suspend. |
| */ |
| #define UFS_DEVICE_QUIRK_NO_LINK_OFF (1 << 3) |
| |
| /* |
| * Few Toshiba UFS device models advertise RX_MIN_ACTIVATETIME_CAPABILITY as |
| * 600us which may not be enough for reliable hibern8 exit hardware sequence |
| * from UFS device. |
| * To workaround this issue, host should set its PA_TACTIVATE time to 1ms even |
| * if device advertises RX_MIN_ACTIVATETIME_CAPABILITY less than 1ms. |
| */ |
| #define UFS_DEVICE_QUIRK_PA_TACTIVATE (1 << 4) |
| |
| /* |
| * Some UFS memory devices may have really low read/write throughput in |
| * FAST AUTO mode, enable this quirk to make sure that FAST AUTO mode is |
| * never enabled for such devices. |
| */ |
| #define UFS_DEVICE_NO_FASTAUTO (1 << 5) |
| |
| /* |
| * It seems some UFS devices may keep drawing more than sleep current |
| * (atleast for 500us) from UFS rails (especially from VCCQ rail). |
| * To avoid this situation, add 2ms delay before putting these UFS |
| * rails in LPM mode. |
| */ |
| #define UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM (1 << 6) |
| |
| struct ufs_hba; |
| void ufs_advertise_fixup_device(struct ufs_hba *hba); |
| |
| static struct ufs_dev_fix ufs_fixups[] = { |
| /* UFS cards deviations table */ |
| UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL, |
| UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM), |
| UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL, UFS_DEVICE_NO_VCCQ), |
| UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL, |
| UFS_DEVICE_QUIRK_RECOVERY_FROM_DL_NAC_ERRORS), |
| UFS_FIX(UFS_VENDOR_SAMSUNG, UFS_ANY_MODEL, |
| UFS_DEVICE_NO_FASTAUTO), |
| UFS_FIX(UFS_VENDOR_TOSHIBA, UFS_ANY_MODEL, |
| UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM), |
| UFS_FIX(UFS_VENDOR_TOSHIBA, "THGLF2G9C8KBADG", |
| UFS_DEVICE_QUIRK_PA_TACTIVATE), |
| UFS_FIX(UFS_VENDOR_TOSHIBA, "THGLF2G9D8KBADG", |
| UFS_DEVICE_QUIRK_PA_TACTIVATE), |
| UFS_FIX(UFS_VENDOR_SKHYNIX, UFS_ANY_MODEL, UFS_DEVICE_NO_VCCQ), |
| |
| END_FIX |
| }; |
| #endif /* UFS_QUIRKS_H_ */ |