| /* | |
| * V4L2 Driver for i.MXL/i.MXL camera (CSI) host | |
| * | |
| * Copyright (C) 2008, Paulius Zaleckas <paulius.zaleckas@teltonika.lt> | |
| * Copyright (C) 2009, Darius Augulis <augulis.darius@gmail.com> | |
| * | |
| * Based on PXA SoC camera driver | |
| * Copyright (C) 2006, Sascha Hauer, Pengutronix | |
| * Copyright (C) 2008, Guennadi Liakhovetski <kernel@pengutronix.de> | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License version 2 as | |
| * published by the Free Software Foundation. | |
| */ | |
| #include <linux/clk.h> | |
| #include <linux/delay.h> | |
| #include <linux/device.h> | |
| #include <linux/dma-mapping.h> | |
| #include <linux/errno.h> | |
| #include <linux/fs.h> | |
| #include <linux/init.h> | |
| #include <linux/interrupt.h> | |
| #include <linux/io.h> | |
| #include <linux/kernel.h> | |
| #include <linux/mm.h> | |
| #include <linux/module.h> | |
| #include <linux/moduleparam.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/sched.h> | |
| #include <linux/slab.h> | |
| #include <linux/time.h> | |
| #include <linux/videodev2.h> | |
| #include <media/soc_camera.h> | |
| #include <media/v4l2-common.h> | |
| #include <media/v4l2-dev.h> | |
| #include <media/videobuf-dma-contig.h> | |
| #include <media/soc_mediabus.h> | |
| #include <asm/dma.h> | |
| #include <asm/fiq.h> | |
| #include <mach/dma-mx1-mx2.h> | |
| #include <mach/hardware.h> | |
| #include <mach/irqs.h> | |
| #include <linux/platform_data/camera-mx1.h> | |
| /* | |
| * CSI registers | |
| */ | |
| #define CSICR1 0x00 /* CSI Control Register 1 */ | |
| #define CSISR 0x08 /* CSI Status Register */ | |
| #define CSIRXR 0x10 /* CSI RxFIFO Register */ | |
| #define CSICR1_RXFF_LEVEL(x) (((x) & 0x3) << 19) | |
| #define CSICR1_SOF_POL (1 << 17) | |
| #define CSICR1_SOF_INTEN (1 << 16) | |
| #define CSICR1_MCLKDIV(x) (((x) & 0xf) << 12) | |
| #define CSICR1_MCLKEN (1 << 9) | |
| #define CSICR1_FCC (1 << 8) | |
| #define CSICR1_BIG_ENDIAN (1 << 7) | |
| #define CSICR1_CLR_RXFIFO (1 << 5) | |
| #define CSICR1_GCLK_MODE (1 << 4) | |
| #define CSICR1_DATA_POL (1 << 2) | |
| #define CSICR1_REDGE (1 << 1) | |
| #define CSICR1_EN (1 << 0) | |
| #define CSISR_SFF_OR_INT (1 << 25) | |
| #define CSISR_RFF_OR_INT (1 << 24) | |
| #define CSISR_STATFF_INT (1 << 21) | |
| #define CSISR_RXFF_INT (1 << 18) | |
| #define CSISR_SOF_INT (1 << 16) | |
| #define CSISR_DRDY (1 << 0) | |
| #define DRIVER_VERSION "0.0.2" | |
| #define DRIVER_NAME "mx1-camera" | |
| #define CSI_IRQ_MASK (CSISR_SFF_OR_INT | CSISR_RFF_OR_INT | \ | |
| CSISR_STATFF_INT | CSISR_RXFF_INT | CSISR_SOF_INT) | |
| #define CSI_BUS_FLAGS (V4L2_MBUS_MASTER | V4L2_MBUS_HSYNC_ACTIVE_HIGH | \ | |
| V4L2_MBUS_VSYNC_ACTIVE_HIGH | V4L2_MBUS_VSYNC_ACTIVE_LOW | \ | |
| V4L2_MBUS_PCLK_SAMPLE_RISING | V4L2_MBUS_PCLK_SAMPLE_FALLING | \ | |
| V4L2_MBUS_DATA_ACTIVE_HIGH | V4L2_MBUS_DATA_ACTIVE_LOW) | |
| #define MAX_VIDEO_MEM 16 /* Video memory limit in megabytes */ | |
| /* | |
| * Structures | |
| */ | |
| /* buffer for one video frame */ | |
| struct mx1_buffer { | |
| /* common v4l buffer stuff -- must be first */ | |
| struct videobuf_buffer vb; | |
| enum v4l2_mbus_pixelcode code; | |
| int inwork; | |
| }; | |
| /* | |
| * i.MX1/i.MXL is only supposed to handle one camera on its Camera Sensor | |
| * Interface. If anyone ever builds hardware to enable more than | |
| * one camera, they will have to modify this driver too | |
| */ | |
| struct mx1_camera_dev { | |
| struct soc_camera_host soc_host; | |
| struct mx1_camera_pdata *pdata; | |
| struct mx1_buffer *active; | |
| struct resource *res; | |
| struct clk *clk; | |
| struct list_head capture; | |
| void __iomem *base; | |
| int dma_chan; | |
| unsigned int irq; | |
| unsigned long mclk; | |
| spinlock_t lock; | |
| }; | |
| /* | |
| * Videobuf operations | |
| */ | |
| static int mx1_videobuf_setup(struct videobuf_queue *vq, unsigned int *count, | |
| unsigned int *size) | |
| { | |
| struct soc_camera_device *icd = vq->priv_data; | |
| *size = icd->sizeimage; | |
| if (!*count) | |
| *count = 32; | |
| if (*size * *count > MAX_VIDEO_MEM * 1024 * 1024) | |
| *count = (MAX_VIDEO_MEM * 1024 * 1024) / *size; | |
| dev_dbg(icd->parent, "count=%d, size=%d\n", *count, *size); | |
| return 0; | |
| } | |
| static void free_buffer(struct videobuf_queue *vq, struct mx1_buffer *buf) | |
| { | |
| struct soc_camera_device *icd = vq->priv_data; | |
| struct videobuf_buffer *vb = &buf->vb; | |
| BUG_ON(in_interrupt()); | |
| dev_dbg(icd->parent, "%s (vb=0x%p) 0x%08lx %d\n", __func__, | |
| vb, vb->baddr, vb->bsize); | |
| /* | |
| * This waits until this buffer is out of danger, i.e., until it is no | |
| * longer in STATE_QUEUED or STATE_ACTIVE | |
| */ | |
| videobuf_waiton(vq, vb, 0, 0); | |
| videobuf_dma_contig_free(vq, vb); | |
| vb->state = VIDEOBUF_NEEDS_INIT; | |
| } | |
| static int mx1_videobuf_prepare(struct videobuf_queue *vq, | |
| struct videobuf_buffer *vb, enum v4l2_field field) | |
| { | |
| struct soc_camera_device *icd = vq->priv_data; | |
| struct mx1_buffer *buf = container_of(vb, struct mx1_buffer, vb); | |
| int ret; | |
| dev_dbg(icd->parent, "%s (vb=0x%p) 0x%08lx %d\n", __func__, | |
| vb, vb->baddr, vb->bsize); | |
| /* Added list head initialization on alloc */ | |
| WARN_ON(!list_empty(&vb->queue)); | |
| BUG_ON(NULL == icd->current_fmt); | |
| /* | |
| * I think, in buf_prepare you only have to protect global data, | |
| * the actual buffer is yours | |
| */ | |
| buf->inwork = 1; | |
| if (buf->code != icd->current_fmt->code || | |
| vb->width != icd->user_width || | |
| vb->height != icd->user_height || | |
| vb->field != field) { | |
| buf->code = icd->current_fmt->code; | |
| vb->width = icd->user_width; | |
| vb->height = icd->user_height; | |
| vb->field = field; | |
| vb->state = VIDEOBUF_NEEDS_INIT; | |
| } | |
| vb->size = icd->sizeimage; | |
| if (0 != vb->baddr && vb->bsize < vb->size) { | |
| ret = -EINVAL; | |
| goto out; | |
| } | |
| if (vb->state == VIDEOBUF_NEEDS_INIT) { | |
| ret = videobuf_iolock(vq, vb, NULL); | |
| if (ret) | |
| goto fail; | |
| vb->state = VIDEOBUF_PREPARED; | |
| } | |
| buf->inwork = 0; | |
| return 0; | |
| fail: | |
| free_buffer(vq, buf); | |
| out: | |
| buf->inwork = 0; | |
| return ret; | |
| } | |
| static int mx1_camera_setup_dma(struct mx1_camera_dev *pcdev) | |
| { | |
| struct videobuf_buffer *vbuf = &pcdev->active->vb; | |
| struct device *dev = pcdev->soc_host.icd->parent; | |
| int ret; | |
| if (unlikely(!pcdev->active)) { | |
| dev_err(dev, "DMA End IRQ with no active buffer\n"); | |
| return -EFAULT; | |
| } | |
| /* setup sg list for future DMA */ | |
| ret = imx_dma_setup_single(pcdev->dma_chan, | |
| videobuf_to_dma_contig(vbuf), | |
| vbuf->size, pcdev->res->start + | |
| CSIRXR, DMA_MODE_READ); | |
| if (unlikely(ret)) | |
| dev_err(dev, "Failed to setup DMA sg list\n"); | |
| return ret; | |
| } | |
| /* Called under spinlock_irqsave(&pcdev->lock, ...) */ | |
| static void mx1_videobuf_queue(struct videobuf_queue *vq, | |
| struct videobuf_buffer *vb) | |
| { | |
| struct soc_camera_device *icd = vq->priv_data; | |
| struct soc_camera_host *ici = to_soc_camera_host(icd->parent); | |
| struct mx1_camera_dev *pcdev = ici->priv; | |
| struct mx1_buffer *buf = container_of(vb, struct mx1_buffer, vb); | |
| dev_dbg(icd->parent, "%s (vb=0x%p) 0x%08lx %d\n", __func__, | |
| vb, vb->baddr, vb->bsize); | |
| list_add_tail(&vb->queue, &pcdev->capture); | |
| vb->state = VIDEOBUF_ACTIVE; | |
| if (!pcdev->active) { | |
| pcdev->active = buf; | |
| /* setup sg list for future DMA */ | |
| if (!mx1_camera_setup_dma(pcdev)) { | |
| unsigned int temp; | |
| /* enable SOF irq */ | |
| temp = __raw_readl(pcdev->base + CSICR1) | | |
| CSICR1_SOF_INTEN; | |
| __raw_writel(temp, pcdev->base + CSICR1); | |
| } | |
| } | |
| } | |
| static void mx1_videobuf_release(struct videobuf_queue *vq, | |
| struct videobuf_buffer *vb) | |
| { | |
| struct mx1_buffer *buf = container_of(vb, struct mx1_buffer, vb); | |
| #ifdef DEBUG | |
| struct soc_camera_device *icd = vq->priv_data; | |
| struct device *dev = icd->parent; | |
| dev_dbg(dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__, | |
| vb, vb->baddr, vb->bsize); | |
| switch (vb->state) { | |
| case VIDEOBUF_ACTIVE: | |
| dev_dbg(dev, "%s (active)\n", __func__); | |
| break; | |
| case VIDEOBUF_QUEUED: | |
| dev_dbg(dev, "%s (queued)\n", __func__); | |
| break; | |
| case VIDEOBUF_PREPARED: | |
| dev_dbg(dev, "%s (prepared)\n", __func__); | |
| break; | |
| default: | |
| dev_dbg(dev, "%s (unknown)\n", __func__); | |
| break; | |
| } | |
| #endif | |
| free_buffer(vq, buf); | |
| } | |
| static void mx1_camera_wakeup(struct mx1_camera_dev *pcdev, | |
| struct videobuf_buffer *vb, | |
| struct mx1_buffer *buf) | |
| { | |
| /* _init is used to debug races, see comment in mx1_camera_reqbufs() */ | |
| list_del_init(&vb->queue); | |
| vb->state = VIDEOBUF_DONE; | |
| v4l2_get_timestamp(&vb->ts); | |
| vb->field_count++; | |
| wake_up(&vb->done); | |
| if (list_empty(&pcdev->capture)) { | |
| pcdev->active = NULL; | |
| return; | |
| } | |
| pcdev->active = list_entry(pcdev->capture.next, | |
| struct mx1_buffer, vb.queue); | |
| /* setup sg list for future DMA */ | |
| if (likely(!mx1_camera_setup_dma(pcdev))) { | |
| unsigned int temp; | |
| /* enable SOF irq */ | |
| temp = __raw_readl(pcdev->base + CSICR1) | CSICR1_SOF_INTEN; | |
| __raw_writel(temp, pcdev->base + CSICR1); | |
| } | |
| } | |
| static void mx1_camera_dma_irq(int channel, void *data) | |
| { | |
| struct mx1_camera_dev *pcdev = data; | |
| struct device *dev = pcdev->soc_host.icd->parent; | |
| struct mx1_buffer *buf; | |
| struct videobuf_buffer *vb; | |
| unsigned long flags; | |
| spin_lock_irqsave(&pcdev->lock, flags); | |
| imx_dma_disable(channel); | |
| if (unlikely(!pcdev->active)) { | |
| dev_err(dev, "DMA End IRQ with no active buffer\n"); | |
| goto out; | |
| } | |
| vb = &pcdev->active->vb; | |
| buf = container_of(vb, struct mx1_buffer, vb); | |
| WARN_ON(buf->inwork || list_empty(&vb->queue)); | |
| dev_dbg(dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__, | |
| vb, vb->baddr, vb->bsize); | |
| mx1_camera_wakeup(pcdev, vb, buf); | |
| out: | |
| spin_unlock_irqrestore(&pcdev->lock, flags); | |
| } | |
| static struct videobuf_queue_ops mx1_videobuf_ops = { | |
| .buf_setup = mx1_videobuf_setup, | |
| .buf_prepare = mx1_videobuf_prepare, | |
| .buf_queue = mx1_videobuf_queue, | |
| .buf_release = mx1_videobuf_release, | |
| }; | |
| static void mx1_camera_init_videobuf(struct videobuf_queue *q, | |
| struct soc_camera_device *icd) | |
| { | |
| struct soc_camera_host *ici = to_soc_camera_host(icd->parent); | |
| struct mx1_camera_dev *pcdev = ici->priv; | |
| videobuf_queue_dma_contig_init(q, &mx1_videobuf_ops, icd->parent, | |
| &pcdev->lock, V4L2_BUF_TYPE_VIDEO_CAPTURE, | |
| V4L2_FIELD_NONE, | |
| sizeof(struct mx1_buffer), icd, &ici->host_lock); | |
| } | |
| static int mclk_get_divisor(struct mx1_camera_dev *pcdev) | |
| { | |
| unsigned int mclk = pcdev->mclk; | |
| unsigned long div; | |
| unsigned long lcdclk; | |
| lcdclk = clk_get_rate(pcdev->clk); | |
| /* | |
| * We verify platform_mclk_10khz != 0, so if anyone breaks it, here | |
| * they get a nice Oops | |
| */ | |
| div = (lcdclk + 2 * mclk - 1) / (2 * mclk) - 1; | |
| dev_dbg(pcdev->soc_host.icd->parent, | |
| "System clock %lukHz, target freq %dkHz, divisor %lu\n", | |
| lcdclk / 1000, mclk / 1000, div); | |
| return div; | |
| } | |
| static void mx1_camera_activate(struct mx1_camera_dev *pcdev) | |
| { | |
| unsigned int csicr1 = CSICR1_EN; | |
| dev_dbg(pcdev->soc_host.v4l2_dev.dev, "Activate device\n"); | |
| clk_prepare_enable(pcdev->clk); | |
| /* enable CSI before doing anything else */ | |
| __raw_writel(csicr1, pcdev->base + CSICR1); | |
| csicr1 |= CSICR1_MCLKEN | CSICR1_FCC | CSICR1_GCLK_MODE; | |
| csicr1 |= CSICR1_MCLKDIV(mclk_get_divisor(pcdev)); | |
| csicr1 |= CSICR1_RXFF_LEVEL(2); /* 16 words */ | |
| __raw_writel(csicr1, pcdev->base + CSICR1); | |
| } | |
| static void mx1_camera_deactivate(struct mx1_camera_dev *pcdev) | |
| { | |
| dev_dbg(pcdev->soc_host.v4l2_dev.dev, "Deactivate device\n"); | |
| /* Disable all CSI interface */ | |
| __raw_writel(0x00, pcdev->base + CSICR1); | |
| clk_disable_unprepare(pcdev->clk); | |
| } | |
| static int mx1_camera_add_device(struct soc_camera_device *icd) | |
| { | |
| dev_info(icd->parent, "MX1 Camera driver attached to camera %d\n", | |
| icd->devnum); | |
| return 0; | |
| } | |
| static void mx1_camera_remove_device(struct soc_camera_device *icd) | |
| { | |
| dev_info(icd->parent, "MX1 Camera driver detached from camera %d\n", | |
| icd->devnum); | |
| } | |
| /* | |
| * The following two functions absolutely depend on the fact, that | |
| * there can be only one camera on i.MX1/i.MXL camera sensor interface | |
| */ | |
| static int mx1_camera_clock_start(struct soc_camera_host *ici) | |
| { | |
| struct mx1_camera_dev *pcdev = ici->priv; | |
| mx1_camera_activate(pcdev); | |
| return 0; | |
| } | |
| static void mx1_camera_clock_stop(struct soc_camera_host *ici) | |
| { | |
| struct mx1_camera_dev *pcdev = ici->priv; | |
| unsigned int csicr1; | |
| /* disable interrupts */ | |
| csicr1 = __raw_readl(pcdev->base + CSICR1) & ~CSI_IRQ_MASK; | |
| __raw_writel(csicr1, pcdev->base + CSICR1); | |
| /* Stop DMA engine */ | |
| imx_dma_disable(pcdev->dma_chan); | |
| mx1_camera_deactivate(pcdev); | |
| } | |
| static int mx1_camera_set_bus_param(struct soc_camera_device *icd) | |
| { | |
| struct v4l2_subdev *sd = soc_camera_to_subdev(icd); | |
| struct soc_camera_host *ici = to_soc_camera_host(icd->parent); | |
| struct mx1_camera_dev *pcdev = ici->priv; | |
| struct v4l2_mbus_config cfg = {.type = V4L2_MBUS_PARALLEL,}; | |
| unsigned long common_flags; | |
| unsigned int csicr1; | |
| int ret; | |
| /* MX1 supports only 8bit buswidth */ | |
| ret = v4l2_subdev_call(sd, video, g_mbus_config, &cfg); | |
| if (!ret) { | |
| common_flags = soc_mbus_config_compatible(&cfg, CSI_BUS_FLAGS); | |
| if (!common_flags) { | |
| dev_warn(icd->parent, | |
| "Flags incompatible: camera 0x%x, host 0x%x\n", | |
| cfg.flags, CSI_BUS_FLAGS); | |
| return -EINVAL; | |
| } | |
| } else if (ret != -ENOIOCTLCMD) { | |
| return ret; | |
| } else { | |
| common_flags = CSI_BUS_FLAGS; | |
| } | |
| /* Make choises, based on platform choice */ | |
| if ((common_flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH) && | |
| (common_flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)) { | |
| if (!pcdev->pdata || | |
| pcdev->pdata->flags & MX1_CAMERA_VSYNC_HIGH) | |
| common_flags &= ~V4L2_MBUS_VSYNC_ACTIVE_LOW; | |
| else | |
| common_flags &= ~V4L2_MBUS_VSYNC_ACTIVE_HIGH; | |
| } | |
| if ((common_flags & V4L2_MBUS_PCLK_SAMPLE_RISING) && | |
| (common_flags & V4L2_MBUS_PCLK_SAMPLE_FALLING)) { | |
| if (!pcdev->pdata || | |
| pcdev->pdata->flags & MX1_CAMERA_PCLK_RISING) | |
| common_flags &= ~V4L2_MBUS_PCLK_SAMPLE_FALLING; | |
| else | |
| common_flags &= ~V4L2_MBUS_PCLK_SAMPLE_RISING; | |
| } | |
| if ((common_flags & V4L2_MBUS_DATA_ACTIVE_HIGH) && | |
| (common_flags & V4L2_MBUS_DATA_ACTIVE_LOW)) { | |
| if (!pcdev->pdata || | |
| pcdev->pdata->flags & MX1_CAMERA_DATA_HIGH) | |
| common_flags &= ~V4L2_MBUS_DATA_ACTIVE_LOW; | |
| else | |
| common_flags &= ~V4L2_MBUS_DATA_ACTIVE_HIGH; | |
| } | |
| cfg.flags = common_flags; | |
| ret = v4l2_subdev_call(sd, video, s_mbus_config, &cfg); | |
| if (ret < 0 && ret != -ENOIOCTLCMD) { | |
| dev_dbg(icd->parent, "camera s_mbus_config(0x%lx) returned %d\n", | |
| common_flags, ret); | |
| return ret; | |
| } | |
| csicr1 = __raw_readl(pcdev->base + CSICR1); | |
| if (common_flags & V4L2_MBUS_PCLK_SAMPLE_RISING) | |
| csicr1 |= CSICR1_REDGE; | |
| if (common_flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH) | |
| csicr1 |= CSICR1_SOF_POL; | |
| if (common_flags & V4L2_MBUS_DATA_ACTIVE_LOW) | |
| csicr1 |= CSICR1_DATA_POL; | |
| __raw_writel(csicr1, pcdev->base + CSICR1); | |
| return 0; | |
| } | |
| static int mx1_camera_set_fmt(struct soc_camera_device *icd, | |
| struct v4l2_format *f) | |
| { | |
| struct v4l2_subdev *sd = soc_camera_to_subdev(icd); | |
| const struct soc_camera_format_xlate *xlate; | |
| struct v4l2_pix_format *pix = &f->fmt.pix; | |
| struct v4l2_mbus_framefmt mf; | |
| int ret, buswidth; | |
| xlate = soc_camera_xlate_by_fourcc(icd, pix->pixelformat); | |
| if (!xlate) { | |
| dev_warn(icd->parent, "Format %x not found\n", | |
| pix->pixelformat); | |
| return -EINVAL; | |
| } | |
| buswidth = xlate->host_fmt->bits_per_sample; | |
| if (buswidth > 8) { | |
| dev_warn(icd->parent, | |
| "bits-per-sample %d for format %x unsupported\n", | |
| buswidth, pix->pixelformat); | |
| return -EINVAL; | |
| } | |
| mf.width = pix->width; | |
| mf.height = pix->height; | |
| mf.field = pix->field; | |
| mf.colorspace = pix->colorspace; | |
| mf.code = xlate->code; | |
| ret = v4l2_subdev_call(sd, video, s_mbus_fmt, &mf); | |
| if (ret < 0) | |
| return ret; | |
| if (mf.code != xlate->code) | |
| return -EINVAL; | |
| pix->width = mf.width; | |
| pix->height = mf.height; | |
| pix->field = mf.field; | |
| pix->colorspace = mf.colorspace; | |
| icd->current_fmt = xlate; | |
| return ret; | |
| } | |
| static int mx1_camera_try_fmt(struct soc_camera_device *icd, | |
| struct v4l2_format *f) | |
| { | |
| struct v4l2_subdev *sd = soc_camera_to_subdev(icd); | |
| const struct soc_camera_format_xlate *xlate; | |
| struct v4l2_pix_format *pix = &f->fmt.pix; | |
| struct v4l2_mbus_framefmt mf; | |
| int ret; | |
| /* TODO: limit to mx1 hardware capabilities */ | |
| xlate = soc_camera_xlate_by_fourcc(icd, pix->pixelformat); | |
| if (!xlate) { | |
| dev_warn(icd->parent, "Format %x not found\n", | |
| pix->pixelformat); | |
| return -EINVAL; | |
| } | |
| mf.width = pix->width; | |
| mf.height = pix->height; | |
| mf.field = pix->field; | |
| mf.colorspace = pix->colorspace; | |
| mf.code = xlate->code; | |
| /* limit to sensor capabilities */ | |
| ret = v4l2_subdev_call(sd, video, try_mbus_fmt, &mf); | |
| if (ret < 0) | |
| return ret; | |
| pix->width = mf.width; | |
| pix->height = mf.height; | |
| pix->field = mf.field; | |
| pix->colorspace = mf.colorspace; | |
| return 0; | |
| } | |
| static int mx1_camera_reqbufs(struct soc_camera_device *icd, | |
| struct v4l2_requestbuffers *p) | |
| { | |
| int i; | |
| /* | |
| * This is for locking debugging only. I removed spinlocks and now I | |
| * check whether .prepare is ever called on a linked buffer, or whether | |
| * a dma IRQ can occur for an in-work or unlinked buffer. Until now | |
| * it hadn't triggered | |
| */ | |
| for (i = 0; i < p->count; i++) { | |
| struct mx1_buffer *buf = container_of(icd->vb_vidq.bufs[i], | |
| struct mx1_buffer, vb); | |
| buf->inwork = 0; | |
| INIT_LIST_HEAD(&buf->vb.queue); | |
| } | |
| return 0; | |
| } | |
| static unsigned int mx1_camera_poll(struct file *file, poll_table *pt) | |
| { | |
| struct soc_camera_device *icd = file->private_data; | |
| struct mx1_buffer *buf; | |
| buf = list_entry(icd->vb_vidq.stream.next, struct mx1_buffer, | |
| vb.stream); | |
| poll_wait(file, &buf->vb.done, pt); | |
| if (buf->vb.state == VIDEOBUF_DONE || | |
| buf->vb.state == VIDEOBUF_ERROR) | |
| return POLLIN | POLLRDNORM; | |
| return 0; | |
| } | |
| static int mx1_camera_querycap(struct soc_camera_host *ici, | |
| struct v4l2_capability *cap) | |
| { | |
| /* cap->name is set by the friendly caller:-> */ | |
| strlcpy(cap->card, "i.MX1/i.MXL Camera", sizeof(cap->card)); | |
| cap->capabilities = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING; | |
| return 0; | |
| } | |
| static struct soc_camera_host_ops mx1_soc_camera_host_ops = { | |
| .owner = THIS_MODULE, | |
| .add = mx1_camera_add_device, | |
| .remove = mx1_camera_remove_device, | |
| .clock_start = mx1_camera_clock_start, | |
| .clock_stop = mx1_camera_clock_stop, | |
| .set_bus_param = mx1_camera_set_bus_param, | |
| .set_fmt = mx1_camera_set_fmt, | |
| .try_fmt = mx1_camera_try_fmt, | |
| .init_videobuf = mx1_camera_init_videobuf, | |
| .reqbufs = mx1_camera_reqbufs, | |
| .poll = mx1_camera_poll, | |
| .querycap = mx1_camera_querycap, | |
| }; | |
| static struct fiq_handler fh = { | |
| .name = "csi_sof" | |
| }; | |
| static int __init mx1_camera_probe(struct platform_device *pdev) | |
| { | |
| struct mx1_camera_dev *pcdev; | |
| struct resource *res; | |
| struct pt_regs regs; | |
| struct clk *clk; | |
| void __iomem *base; | |
| unsigned int irq; | |
| int err = 0; | |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
| irq = platform_get_irq(pdev, 0); | |
| if (!res || (int)irq <= 0) { | |
| err = -ENODEV; | |
| goto exit; | |
| } | |
| clk = clk_get(&pdev->dev, "csi_clk"); | |
| if (IS_ERR(clk)) { | |
| err = PTR_ERR(clk); | |
| goto exit; | |
| } | |
| pcdev = kzalloc(sizeof(*pcdev), GFP_KERNEL); | |
| if (!pcdev) { | |
| dev_err(&pdev->dev, "Could not allocate pcdev\n"); | |
| err = -ENOMEM; | |
| goto exit_put_clk; | |
| } | |
| pcdev->res = res; | |
| pcdev->clk = clk; | |
| pcdev->pdata = pdev->dev.platform_data; | |
| if (pcdev->pdata) | |
| pcdev->mclk = pcdev->pdata->mclk_10khz * 10000; | |
| if (!pcdev->mclk) { | |
| dev_warn(&pdev->dev, | |
| "mclk_10khz == 0! Please, fix your platform data. " | |
| "Using default 20MHz\n"); | |
| pcdev->mclk = 20000000; | |
| } | |
| INIT_LIST_HEAD(&pcdev->capture); | |
| spin_lock_init(&pcdev->lock); | |
| /* | |
| * Request the regions. | |
| */ | |
| if (!request_mem_region(res->start, resource_size(res), DRIVER_NAME)) { | |
| err = -EBUSY; | |
| goto exit_kfree; | |
| } | |
| base = ioremap(res->start, resource_size(res)); | |
| if (!base) { | |
| err = -ENOMEM; | |
| goto exit_release; | |
| } | |
| pcdev->irq = irq; | |
| pcdev->base = base; | |
| /* request dma */ | |
| pcdev->dma_chan = imx_dma_request_by_prio(DRIVER_NAME, DMA_PRIO_HIGH); | |
| if (pcdev->dma_chan < 0) { | |
| dev_err(&pdev->dev, "Can't request DMA for MX1 CSI\n"); | |
| err = -EBUSY; | |
| goto exit_iounmap; | |
| } | |
| dev_dbg(&pdev->dev, "got DMA channel %d\n", pcdev->dma_chan); | |
| imx_dma_setup_handlers(pcdev->dma_chan, mx1_camera_dma_irq, NULL, | |
| pcdev); | |
| imx_dma_config_channel(pcdev->dma_chan, IMX_DMA_TYPE_FIFO, | |
| IMX_DMA_MEMSIZE_32, MX1_DMA_REQ_CSI_R, 0); | |
| /* burst length : 16 words = 64 bytes */ | |
| imx_dma_config_burstlen(pcdev->dma_chan, 0); | |
| /* request irq */ | |
| err = claim_fiq(&fh); | |
| if (err) { | |
| dev_err(&pdev->dev, "Camera interrupt register failed\n"); | |
| goto exit_free_dma; | |
| } | |
| set_fiq_handler(&mx1_camera_sof_fiq_start, &mx1_camera_sof_fiq_end - | |
| &mx1_camera_sof_fiq_start); | |
| regs.ARM_r8 = (long)MX1_DMA_DIMR; | |
| regs.ARM_r9 = (long)MX1_DMA_CCR(pcdev->dma_chan); | |
| regs.ARM_r10 = (long)pcdev->base + CSICR1; | |
| regs.ARM_fp = (long)pcdev->base + CSISR; | |
| regs.ARM_sp = 1 << pcdev->dma_chan; | |
| set_fiq_regs(®s); | |
| mxc_set_irq_fiq(irq, 1); | |
| enable_fiq(irq); | |
| pcdev->soc_host.drv_name = DRIVER_NAME; | |
| pcdev->soc_host.ops = &mx1_soc_camera_host_ops; | |
| pcdev->soc_host.priv = pcdev; | |
| pcdev->soc_host.v4l2_dev.dev = &pdev->dev; | |
| pcdev->soc_host.nr = pdev->id; | |
| err = soc_camera_host_register(&pcdev->soc_host); | |
| if (err) | |
| goto exit_free_irq; | |
| dev_info(&pdev->dev, "MX1 Camera driver loaded\n"); | |
| return 0; | |
| exit_free_irq: | |
| disable_fiq(irq); | |
| mxc_set_irq_fiq(irq, 0); | |
| release_fiq(&fh); | |
| exit_free_dma: | |
| imx_dma_free(pcdev->dma_chan); | |
| exit_iounmap: | |
| iounmap(base); | |
| exit_release: | |
| release_mem_region(res->start, resource_size(res)); | |
| exit_kfree: | |
| kfree(pcdev); | |
| exit_put_clk: | |
| clk_put(clk); | |
| exit: | |
| return err; | |
| } | |
| static int __exit mx1_camera_remove(struct platform_device *pdev) | |
| { | |
| struct soc_camera_host *soc_host = to_soc_camera_host(&pdev->dev); | |
| struct mx1_camera_dev *pcdev = container_of(soc_host, | |
| struct mx1_camera_dev, soc_host); | |
| struct resource *res; | |
| imx_dma_free(pcdev->dma_chan); | |
| disable_fiq(pcdev->irq); | |
| mxc_set_irq_fiq(pcdev->irq, 0); | |
| release_fiq(&fh); | |
| clk_put(pcdev->clk); | |
| soc_camera_host_unregister(soc_host); | |
| iounmap(pcdev->base); | |
| res = pcdev->res; | |
| release_mem_region(res->start, resource_size(res)); | |
| kfree(pcdev); | |
| dev_info(&pdev->dev, "MX1 Camera driver unloaded\n"); | |
| return 0; | |
| } | |
| static struct platform_driver mx1_camera_driver = { | |
| .driver = { | |
| .name = DRIVER_NAME, | |
| }, | |
| .remove = __exit_p(mx1_camera_remove), | |
| }; | |
| module_platform_driver_probe(mx1_camera_driver, mx1_camera_probe); | |
| MODULE_DESCRIPTION("i.MX1/i.MXL SoC Camera Host driver"); | |
| MODULE_AUTHOR("Paulius Zaleckas <paulius.zaleckas@teltonika.lt>"); | |
| MODULE_LICENSE("GPL v2"); | |
| MODULE_VERSION(DRIVER_VERSION); | |
| MODULE_ALIAS("platform:" DRIVER_NAME); |