| /* | |
| * Copyright (C) 2010 Google, Inc. | |
| * Copyright (C) 2013 NVIDIA Corporation | |
| * | |
| * Author: | |
| * Erik Gilling <konkers@google.com> | |
| * Benoit Goby <benoit@android.com> | |
| * Venu Byravarasu <vbyravarasu@nvidia.com> | |
| * | |
| * This software is licensed under the terms of the GNU General Public | |
| * License version 2, as published by the Free Software Foundation, and | |
| * may be copied, distributed, and modified under those terms. | |
| * | |
| * This program is distributed in the hope that it will be useful, | |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| * GNU General Public License for more details. | |
| * | |
| */ | |
| #include <linux/resource.h> | |
| #include <linux/delay.h> | |
| #include <linux/slab.h> | |
| #include <linux/err.h> | |
| #include <linux/export.h> | |
| #include <linux/module.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/io.h> | |
| #include <linux/gpio.h> | |
| #include <linux/of.h> | |
| #include <linux/of_device.h> | |
| #include <linux/of_gpio.h> | |
| #include <linux/usb/otg.h> | |
| #include <linux/usb/ulpi.h> | |
| #include <linux/usb/of.h> | |
| #include <asm/mach-types.h> | |
| #include <linux/usb/ehci_def.h> | |
| #include <linux/usb/tegra_usb_phy.h> | |
| #include <linux/regulator/consumer.h> | |
| #define ULPI_VIEWPORT 0x170 | |
| /* PORTSC PTS/PHCD bits, Tegra20 only */ | |
| #define TEGRA_USB_PORTSC1 0x184 | |
| #define TEGRA_USB_PORTSC1_PTS(x) (((x) & 0x3) << 30) | |
| #define TEGRA_USB_PORTSC1_PHCD (1 << 23) | |
| /* HOSTPC1 PTS/PHCD bits, Tegra30 and above */ | |
| #define TEGRA_USB_HOSTPC1_DEVLC 0x1b4 | |
| #define TEGRA_USB_HOSTPC1_DEVLC_PTS(x) (((x) & 0x7) << 29) | |
| #define TEGRA_USB_HOSTPC1_DEVLC_PHCD (1 << 22) | |
| /* Bits of PORTSC1, which will get cleared by writing 1 into them */ | |
| #define TEGRA_PORTSC1_RWC_BITS (PORT_CSC | PORT_PEC | PORT_OCC) | |
| #define USB_SUSP_CTRL 0x400 | |
| #define USB_WAKE_ON_CNNT_EN_DEV (1 << 3) | |
| #define USB_WAKE_ON_DISCON_EN_DEV (1 << 4) | |
| #define USB_SUSP_CLR (1 << 5) | |
| #define USB_PHY_CLK_VALID (1 << 7) | |
| #define UTMIP_RESET (1 << 11) | |
| #define UHSIC_RESET (1 << 11) | |
| #define UTMIP_PHY_ENABLE (1 << 12) | |
| #define ULPI_PHY_ENABLE (1 << 13) | |
| #define USB_SUSP_SET (1 << 14) | |
| #define USB_WAKEUP_DEBOUNCE_COUNT(x) (((x) & 0x7) << 16) | |
| #define USB1_LEGACY_CTRL 0x410 | |
| #define USB1_NO_LEGACY_MODE (1 << 0) | |
| #define USB1_VBUS_SENSE_CTL_MASK (3 << 1) | |
| #define USB1_VBUS_SENSE_CTL_VBUS_WAKEUP (0 << 1) | |
| #define USB1_VBUS_SENSE_CTL_AB_SESS_VLD_OR_VBUS_WAKEUP \ | |
| (1 << 1) | |
| #define USB1_VBUS_SENSE_CTL_AB_SESS_VLD (2 << 1) | |
| #define USB1_VBUS_SENSE_CTL_A_SESS_VLD (3 << 1) | |
| #define ULPI_TIMING_CTRL_0 0x424 | |
| #define ULPI_OUTPUT_PINMUX_BYP (1 << 10) | |
| #define ULPI_CLKOUT_PINMUX_BYP (1 << 11) | |
| #define ULPI_TIMING_CTRL_1 0x428 | |
| #define ULPI_DATA_TRIMMER_LOAD (1 << 0) | |
| #define ULPI_DATA_TRIMMER_SEL(x) (((x) & 0x7) << 1) | |
| #define ULPI_STPDIRNXT_TRIMMER_LOAD (1 << 16) | |
| #define ULPI_STPDIRNXT_TRIMMER_SEL(x) (((x) & 0x7) << 17) | |
| #define ULPI_DIR_TRIMMER_LOAD (1 << 24) | |
| #define ULPI_DIR_TRIMMER_SEL(x) (((x) & 0x7) << 25) | |
| #define UTMIP_PLL_CFG1 0x804 | |
| #define UTMIP_XTAL_FREQ_COUNT(x) (((x) & 0xfff) << 0) | |
| #define UTMIP_PLLU_ENABLE_DLY_COUNT(x) (((x) & 0x1f) << 27) | |
| #define UTMIP_XCVR_CFG0 0x808 | |
| #define UTMIP_XCVR_SETUP(x) (((x) & 0xf) << 0) | |
| #define UTMIP_XCVR_SETUP_MSB(x) ((((x) & 0x70) >> 4) << 22) | |
| #define UTMIP_XCVR_LSRSLEW(x) (((x) & 0x3) << 8) | |
| #define UTMIP_XCVR_LSFSLEW(x) (((x) & 0x3) << 10) | |
| #define UTMIP_FORCE_PD_POWERDOWN (1 << 14) | |
| #define UTMIP_FORCE_PD2_POWERDOWN (1 << 16) | |
| #define UTMIP_FORCE_PDZI_POWERDOWN (1 << 18) | |
| #define UTMIP_XCVR_LSBIAS_SEL (1 << 21) | |
| #define UTMIP_XCVR_HSSLEW(x) (((x) & 0x3) << 4) | |
| #define UTMIP_XCVR_HSSLEW_MSB(x) ((((x) & 0x1fc) >> 2) << 25) | |
| #define UTMIP_BIAS_CFG0 0x80c | |
| #define UTMIP_OTGPD (1 << 11) | |
| #define UTMIP_BIASPD (1 << 10) | |
| #define UTMIP_HSSQUELCH_LEVEL(x) (((x) & 0x3) << 0) | |
| #define UTMIP_HSDISCON_LEVEL(x) (((x) & 0x3) << 2) | |
| #define UTMIP_HSDISCON_LEVEL_MSB(x) ((((x) & 0x4) >> 2) << 24) | |
| #define UTMIP_HSRX_CFG0 0x810 | |
| #define UTMIP_ELASTIC_LIMIT(x) (((x) & 0x1f) << 10) | |
| #define UTMIP_IDLE_WAIT(x) (((x) & 0x1f) << 15) | |
| #define UTMIP_HSRX_CFG1 0x814 | |
| #define UTMIP_HS_SYNC_START_DLY(x) (((x) & 0x1f) << 1) | |
| #define UTMIP_TX_CFG0 0x820 | |
| #define UTMIP_FS_PREABMLE_J (1 << 19) | |
| #define UTMIP_HS_DISCON_DISABLE (1 << 8) | |
| #define UTMIP_MISC_CFG0 0x824 | |
| #define UTMIP_DPDM_OBSERVE (1 << 26) | |
| #define UTMIP_DPDM_OBSERVE_SEL(x) (((x) & 0xf) << 27) | |
| #define UTMIP_DPDM_OBSERVE_SEL_FS_J UTMIP_DPDM_OBSERVE_SEL(0xf) | |
| #define UTMIP_DPDM_OBSERVE_SEL_FS_K UTMIP_DPDM_OBSERVE_SEL(0xe) | |
| #define UTMIP_DPDM_OBSERVE_SEL_FS_SE1 UTMIP_DPDM_OBSERVE_SEL(0xd) | |
| #define UTMIP_DPDM_OBSERVE_SEL_FS_SE0 UTMIP_DPDM_OBSERVE_SEL(0xc) | |
| #define UTMIP_SUSPEND_EXIT_ON_EDGE (1 << 22) | |
| #define UTMIP_MISC_CFG1 0x828 | |
| #define UTMIP_PLL_ACTIVE_DLY_COUNT(x) (((x) & 0x1f) << 18) | |
| #define UTMIP_PLLU_STABLE_COUNT(x) (((x) & 0xfff) << 6) | |
| #define UTMIP_DEBOUNCE_CFG0 0x82c | |
| #define UTMIP_BIAS_DEBOUNCE_A(x) (((x) & 0xffff) << 0) | |
| #define UTMIP_BAT_CHRG_CFG0 0x830 | |
| #define UTMIP_PD_CHRG (1 << 0) | |
| #define UTMIP_SPARE_CFG0 0x834 | |
| #define FUSE_SETUP_SEL (1 << 3) | |
| #define UTMIP_XCVR_CFG1 0x838 | |
| #define UTMIP_FORCE_PDDISC_POWERDOWN (1 << 0) | |
| #define UTMIP_FORCE_PDCHRP_POWERDOWN (1 << 2) | |
| #define UTMIP_FORCE_PDDR_POWERDOWN (1 << 4) | |
| #define UTMIP_XCVR_TERM_RANGE_ADJ(x) (((x) & 0xf) << 18) | |
| #define UTMIP_BIAS_CFG1 0x83c | |
| #define UTMIP_BIAS_PDTRK_COUNT(x) (((x) & 0x1f) << 3) | |
| /* For Tegra30 and above only, the address is different in Tegra20 */ | |
| #define USB_USBMODE 0x1f8 | |
| #define USB_USBMODE_MASK (3 << 0) | |
| #define USB_USBMODE_HOST (3 << 0) | |
| #define USB_USBMODE_DEVICE (2 << 0) | |
| static DEFINE_SPINLOCK(utmip_pad_lock); | |
| static int utmip_pad_count; | |
| struct tegra_xtal_freq { | |
| int freq; | |
| u8 enable_delay; | |
| u8 stable_count; | |
| u8 active_delay; | |
| u8 xtal_freq_count; | |
| u16 debounce; | |
| }; | |
| static const struct tegra_xtal_freq tegra_freq_table[] = { | |
| { | |
| .freq = 12000000, | |
| .enable_delay = 0x02, | |
| .stable_count = 0x2F, | |
| .active_delay = 0x04, | |
| .xtal_freq_count = 0x76, | |
| .debounce = 0x7530, | |
| }, | |
| { | |
| .freq = 13000000, | |
| .enable_delay = 0x02, | |
| .stable_count = 0x33, | |
| .active_delay = 0x05, | |
| .xtal_freq_count = 0x7F, | |
| .debounce = 0x7EF4, | |
| }, | |
| { | |
| .freq = 19200000, | |
| .enable_delay = 0x03, | |
| .stable_count = 0x4B, | |
| .active_delay = 0x06, | |
| .xtal_freq_count = 0xBB, | |
| .debounce = 0xBB80, | |
| }, | |
| { | |
| .freq = 26000000, | |
| .enable_delay = 0x04, | |
| .stable_count = 0x66, | |
| .active_delay = 0x09, | |
| .xtal_freq_count = 0xFE, | |
| .debounce = 0xFDE8, | |
| }, | |
| }; | |
| static void set_pts(struct tegra_usb_phy *phy, u8 pts_val) | |
| { | |
| void __iomem *base = phy->regs; | |
| unsigned long val; | |
| if (phy->soc_config->has_hostpc) { | |
| val = readl(base + TEGRA_USB_HOSTPC1_DEVLC); | |
| val &= ~TEGRA_USB_HOSTPC1_DEVLC_PTS(~0); | |
| val |= TEGRA_USB_HOSTPC1_DEVLC_PTS(pts_val); | |
| writel(val, base + TEGRA_USB_HOSTPC1_DEVLC); | |
| } else { | |
| val = readl(base + TEGRA_USB_PORTSC1) & ~TEGRA_PORTSC1_RWC_BITS; | |
| val &= ~TEGRA_USB_PORTSC1_PTS(~0); | |
| val |= TEGRA_USB_PORTSC1_PTS(pts_val); | |
| writel(val, base + TEGRA_USB_PORTSC1); | |
| } | |
| } | |
| static void set_phcd(struct tegra_usb_phy *phy, bool enable) | |
| { | |
| void __iomem *base = phy->regs; | |
| unsigned long val; | |
| if (phy->soc_config->has_hostpc) { | |
| val = readl(base + TEGRA_USB_HOSTPC1_DEVLC); | |
| if (enable) | |
| val |= TEGRA_USB_HOSTPC1_DEVLC_PHCD; | |
| else | |
| val &= ~TEGRA_USB_HOSTPC1_DEVLC_PHCD; | |
| writel(val, base + TEGRA_USB_HOSTPC1_DEVLC); | |
| } else { | |
| val = readl(base + TEGRA_USB_PORTSC1) & ~PORT_RWC_BITS; | |
| if (enable) | |
| val |= TEGRA_USB_PORTSC1_PHCD; | |
| else | |
| val &= ~TEGRA_USB_PORTSC1_PHCD; | |
| writel(val, base + TEGRA_USB_PORTSC1); | |
| } | |
| } | |
| static int utmip_pad_open(struct tegra_usb_phy *phy) | |
| { | |
| phy->pad_clk = devm_clk_get(phy->u_phy.dev, "utmi-pads"); | |
| if (IS_ERR(phy->pad_clk)) { | |
| pr_err("%s: can't get utmip pad clock\n", __func__); | |
| return PTR_ERR(phy->pad_clk); | |
| } | |
| return 0; | |
| } | |
| static void utmip_pad_power_on(struct tegra_usb_phy *phy) | |
| { | |
| unsigned long val, flags; | |
| void __iomem *base = phy->pad_regs; | |
| struct tegra_utmip_config *config = phy->config; | |
| clk_prepare_enable(phy->pad_clk); | |
| spin_lock_irqsave(&utmip_pad_lock, flags); | |
| if (utmip_pad_count++ == 0) { | |
| val = readl(base + UTMIP_BIAS_CFG0); | |
| val &= ~(UTMIP_OTGPD | UTMIP_BIASPD); | |
| if (phy->soc_config->requires_extra_tuning_parameters) { | |
| val &= ~(UTMIP_HSSQUELCH_LEVEL(~0) | | |
| UTMIP_HSDISCON_LEVEL(~0) | | |
| UTMIP_HSDISCON_LEVEL_MSB(~0)); | |
| val |= UTMIP_HSSQUELCH_LEVEL(config->hssquelch_level); | |
| val |= UTMIP_HSDISCON_LEVEL(config->hsdiscon_level); | |
| val |= UTMIP_HSDISCON_LEVEL_MSB(config->hsdiscon_level); | |
| } | |
| writel(val, base + UTMIP_BIAS_CFG0); | |
| } | |
| spin_unlock_irqrestore(&utmip_pad_lock, flags); | |
| clk_disable_unprepare(phy->pad_clk); | |
| } | |
| static int utmip_pad_power_off(struct tegra_usb_phy *phy) | |
| { | |
| unsigned long val, flags; | |
| void __iomem *base = phy->pad_regs; | |
| if (!utmip_pad_count) { | |
| pr_err("%s: utmip pad already powered off\n", __func__); | |
| return -EINVAL; | |
| } | |
| clk_prepare_enable(phy->pad_clk); | |
| spin_lock_irqsave(&utmip_pad_lock, flags); | |
| if (--utmip_pad_count == 0) { | |
| val = readl(base + UTMIP_BIAS_CFG0); | |
| val |= UTMIP_OTGPD | UTMIP_BIASPD; | |
| writel(val, base + UTMIP_BIAS_CFG0); | |
| } | |
| spin_unlock_irqrestore(&utmip_pad_lock, flags); | |
| clk_disable_unprepare(phy->pad_clk); | |
| return 0; | |
| } | |
| static int utmi_wait_register(void __iomem *reg, u32 mask, u32 result) | |
| { | |
| unsigned long timeout = 2000; | |
| do { | |
| if ((readl(reg) & mask) == result) | |
| return 0; | |
| udelay(1); | |
| timeout--; | |
| } while (timeout); | |
| return -1; | |
| } | |
| static void utmi_phy_clk_disable(struct tegra_usb_phy *phy) | |
| { | |
| unsigned long val; | |
| void __iomem *base = phy->regs; | |
| if (phy->is_legacy_phy) { | |
| val = readl(base + USB_SUSP_CTRL); | |
| val |= USB_SUSP_SET; | |
| writel(val, base + USB_SUSP_CTRL); | |
| udelay(10); | |
| val = readl(base + USB_SUSP_CTRL); | |
| val &= ~USB_SUSP_SET; | |
| writel(val, base + USB_SUSP_CTRL); | |
| } else | |
| set_phcd(phy, true); | |
| if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, 0) < 0) | |
| pr_err("%s: timeout waiting for phy to stabilize\n", __func__); | |
| } | |
| static void utmi_phy_clk_enable(struct tegra_usb_phy *phy) | |
| { | |
| unsigned long val; | |
| void __iomem *base = phy->regs; | |
| if (phy->is_legacy_phy) { | |
| val = readl(base + USB_SUSP_CTRL); | |
| val |= USB_SUSP_CLR; | |
| writel(val, base + USB_SUSP_CTRL); | |
| udelay(10); | |
| val = readl(base + USB_SUSP_CTRL); | |
| val &= ~USB_SUSP_CLR; | |
| writel(val, base + USB_SUSP_CTRL); | |
| } else | |
| set_phcd(phy, false); | |
| if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, | |
| USB_PHY_CLK_VALID)) | |
| pr_err("%s: timeout waiting for phy to stabilize\n", __func__); | |
| } | |
| static int utmi_phy_power_on(struct tegra_usb_phy *phy) | |
| { | |
| unsigned long val; | |
| void __iomem *base = phy->regs; | |
| struct tegra_utmip_config *config = phy->config; | |
| val = readl(base + USB_SUSP_CTRL); | |
| val |= UTMIP_RESET; | |
| writel(val, base + USB_SUSP_CTRL); | |
| if (phy->is_legacy_phy) { | |
| val = readl(base + USB1_LEGACY_CTRL); | |
| val |= USB1_NO_LEGACY_MODE; | |
| writel(val, base + USB1_LEGACY_CTRL); | |
| } | |
| val = readl(base + UTMIP_TX_CFG0); | |
| val |= UTMIP_FS_PREABMLE_J; | |
| writel(val, base + UTMIP_TX_CFG0); | |
| val = readl(base + UTMIP_HSRX_CFG0); | |
| val &= ~(UTMIP_IDLE_WAIT(~0) | UTMIP_ELASTIC_LIMIT(~0)); | |
| val |= UTMIP_IDLE_WAIT(config->idle_wait_delay); | |
| val |= UTMIP_ELASTIC_LIMIT(config->elastic_limit); | |
| writel(val, base + UTMIP_HSRX_CFG0); | |
| val = readl(base + UTMIP_HSRX_CFG1); | |
| val &= ~UTMIP_HS_SYNC_START_DLY(~0); | |
| val |= UTMIP_HS_SYNC_START_DLY(config->hssync_start_delay); | |
| writel(val, base + UTMIP_HSRX_CFG1); | |
| val = readl(base + UTMIP_DEBOUNCE_CFG0); | |
| val &= ~UTMIP_BIAS_DEBOUNCE_A(~0); | |
| val |= UTMIP_BIAS_DEBOUNCE_A(phy->freq->debounce); | |
| writel(val, base + UTMIP_DEBOUNCE_CFG0); | |
| val = readl(base + UTMIP_MISC_CFG0); | |
| val &= ~UTMIP_SUSPEND_EXIT_ON_EDGE; | |
| writel(val, base + UTMIP_MISC_CFG0); | |
| if (!phy->soc_config->utmi_pll_config_in_car_module) { | |
| val = readl(base + UTMIP_MISC_CFG1); | |
| val &= ~(UTMIP_PLL_ACTIVE_DLY_COUNT(~0) | | |
| UTMIP_PLLU_STABLE_COUNT(~0)); | |
| val |= UTMIP_PLL_ACTIVE_DLY_COUNT(phy->freq->active_delay) | | |
| UTMIP_PLLU_STABLE_COUNT(phy->freq->stable_count); | |
| writel(val, base + UTMIP_MISC_CFG1); | |
| val = readl(base + UTMIP_PLL_CFG1); | |
| val &= ~(UTMIP_XTAL_FREQ_COUNT(~0) | | |
| UTMIP_PLLU_ENABLE_DLY_COUNT(~0)); | |
| val |= UTMIP_XTAL_FREQ_COUNT(phy->freq->xtal_freq_count) | | |
| UTMIP_PLLU_ENABLE_DLY_COUNT(phy->freq->enable_delay); | |
| writel(val, base + UTMIP_PLL_CFG1); | |
| } | |
| if (phy->mode == USB_DR_MODE_PERIPHERAL) { | |
| val = readl(base + USB_SUSP_CTRL); | |
| val &= ~(USB_WAKE_ON_CNNT_EN_DEV | USB_WAKE_ON_DISCON_EN_DEV); | |
| writel(val, base + USB_SUSP_CTRL); | |
| val = readl(base + UTMIP_BAT_CHRG_CFG0); | |
| val &= ~UTMIP_PD_CHRG; | |
| writel(val, base + UTMIP_BAT_CHRG_CFG0); | |
| } else { | |
| val = readl(base + UTMIP_BAT_CHRG_CFG0); | |
| val |= UTMIP_PD_CHRG; | |
| writel(val, base + UTMIP_BAT_CHRG_CFG0); | |
| } | |
| utmip_pad_power_on(phy); | |
| val = readl(base + UTMIP_XCVR_CFG0); | |
| val &= ~(UTMIP_FORCE_PD_POWERDOWN | UTMIP_FORCE_PD2_POWERDOWN | | |
| UTMIP_FORCE_PDZI_POWERDOWN | UTMIP_XCVR_LSBIAS_SEL | | |
| UTMIP_XCVR_SETUP(~0) | UTMIP_XCVR_SETUP_MSB(~0) | | |
| UTMIP_XCVR_LSFSLEW(~0) | UTMIP_XCVR_LSRSLEW(~0)); | |
| if (!config->xcvr_setup_use_fuses) { | |
| val |= UTMIP_XCVR_SETUP(config->xcvr_setup); | |
| val |= UTMIP_XCVR_SETUP_MSB(config->xcvr_setup); | |
| } | |
| val |= UTMIP_XCVR_LSFSLEW(config->xcvr_lsfslew); | |
| val |= UTMIP_XCVR_LSRSLEW(config->xcvr_lsrslew); | |
| if (phy->soc_config->requires_extra_tuning_parameters) { | |
| val &= ~(UTMIP_XCVR_HSSLEW(~0) | UTMIP_XCVR_HSSLEW_MSB(~0)); | |
| val |= UTMIP_XCVR_HSSLEW(config->xcvr_hsslew); | |
| val |= UTMIP_XCVR_HSSLEW_MSB(config->xcvr_hsslew); | |
| } | |
| writel(val, base + UTMIP_XCVR_CFG0); | |
| val = readl(base + UTMIP_XCVR_CFG1); | |
| val &= ~(UTMIP_FORCE_PDDISC_POWERDOWN | UTMIP_FORCE_PDCHRP_POWERDOWN | | |
| UTMIP_FORCE_PDDR_POWERDOWN | UTMIP_XCVR_TERM_RANGE_ADJ(~0)); | |
| val |= UTMIP_XCVR_TERM_RANGE_ADJ(config->term_range_adj); | |
| writel(val, base + UTMIP_XCVR_CFG1); | |
| val = readl(base + UTMIP_BIAS_CFG1); | |
| val &= ~UTMIP_BIAS_PDTRK_COUNT(~0); | |
| val |= UTMIP_BIAS_PDTRK_COUNT(0x5); | |
| writel(val, base + UTMIP_BIAS_CFG1); | |
| val = readl(base + UTMIP_SPARE_CFG0); | |
| if (config->xcvr_setup_use_fuses) | |
| val |= FUSE_SETUP_SEL; | |
| else | |
| val &= ~FUSE_SETUP_SEL; | |
| writel(val, base + UTMIP_SPARE_CFG0); | |
| if (!phy->is_legacy_phy) { | |
| val = readl(base + USB_SUSP_CTRL); | |
| val |= UTMIP_PHY_ENABLE; | |
| writel(val, base + USB_SUSP_CTRL); | |
| } | |
| val = readl(base + USB_SUSP_CTRL); | |
| val &= ~UTMIP_RESET; | |
| writel(val, base + USB_SUSP_CTRL); | |
| if (phy->is_legacy_phy) { | |
| val = readl(base + USB1_LEGACY_CTRL); | |
| val &= ~USB1_VBUS_SENSE_CTL_MASK; | |
| val |= USB1_VBUS_SENSE_CTL_A_SESS_VLD; | |
| writel(val, base + USB1_LEGACY_CTRL); | |
| val = readl(base + USB_SUSP_CTRL); | |
| val &= ~USB_SUSP_SET; | |
| writel(val, base + USB_SUSP_CTRL); | |
| } | |
| utmi_phy_clk_enable(phy); | |
| if (phy->soc_config->requires_usbmode_setup) { | |
| val = readl(base + USB_USBMODE); | |
| val &= ~USB_USBMODE_MASK; | |
| if (phy->mode == USB_DR_MODE_HOST) | |
| val |= USB_USBMODE_HOST; | |
| else | |
| val |= USB_USBMODE_DEVICE; | |
| writel(val, base + USB_USBMODE); | |
| } | |
| if (!phy->is_legacy_phy) | |
| set_pts(phy, 0); | |
| return 0; | |
| } | |
| static int utmi_phy_power_off(struct tegra_usb_phy *phy) | |
| { | |
| unsigned long val; | |
| void __iomem *base = phy->regs; | |
| utmi_phy_clk_disable(phy); | |
| if (phy->mode == USB_DR_MODE_PERIPHERAL) { | |
| val = readl(base + USB_SUSP_CTRL); | |
| val &= ~USB_WAKEUP_DEBOUNCE_COUNT(~0); | |
| val |= USB_WAKE_ON_CNNT_EN_DEV | USB_WAKEUP_DEBOUNCE_COUNT(5); | |
| writel(val, base + USB_SUSP_CTRL); | |
| } | |
| val = readl(base + USB_SUSP_CTRL); | |
| val |= UTMIP_RESET; | |
| writel(val, base + USB_SUSP_CTRL); | |
| val = readl(base + UTMIP_BAT_CHRG_CFG0); | |
| val |= UTMIP_PD_CHRG; | |
| writel(val, base + UTMIP_BAT_CHRG_CFG0); | |
| val = readl(base + UTMIP_XCVR_CFG0); | |
| val |= UTMIP_FORCE_PD_POWERDOWN | UTMIP_FORCE_PD2_POWERDOWN | | |
| UTMIP_FORCE_PDZI_POWERDOWN; | |
| writel(val, base + UTMIP_XCVR_CFG0); | |
| val = readl(base + UTMIP_XCVR_CFG1); | |
| val |= UTMIP_FORCE_PDDISC_POWERDOWN | UTMIP_FORCE_PDCHRP_POWERDOWN | | |
| UTMIP_FORCE_PDDR_POWERDOWN; | |
| writel(val, base + UTMIP_XCVR_CFG1); | |
| return utmip_pad_power_off(phy); | |
| } | |
| static void utmi_phy_preresume(struct tegra_usb_phy *phy) | |
| { | |
| unsigned long val; | |
| void __iomem *base = phy->regs; | |
| val = readl(base + UTMIP_TX_CFG0); | |
| val |= UTMIP_HS_DISCON_DISABLE; | |
| writel(val, base + UTMIP_TX_CFG0); | |
| } | |
| static void utmi_phy_postresume(struct tegra_usb_phy *phy) | |
| { | |
| unsigned long val; | |
| void __iomem *base = phy->regs; | |
| val = readl(base + UTMIP_TX_CFG0); | |
| val &= ~UTMIP_HS_DISCON_DISABLE; | |
| writel(val, base + UTMIP_TX_CFG0); | |
| } | |
| static void utmi_phy_restore_start(struct tegra_usb_phy *phy, | |
| enum tegra_usb_phy_port_speed port_speed) | |
| { | |
| unsigned long val; | |
| void __iomem *base = phy->regs; | |
| val = readl(base + UTMIP_MISC_CFG0); | |
| val &= ~UTMIP_DPDM_OBSERVE_SEL(~0); | |
| if (port_speed == TEGRA_USB_PHY_PORT_SPEED_LOW) | |
| val |= UTMIP_DPDM_OBSERVE_SEL_FS_K; | |
| else | |
| val |= UTMIP_DPDM_OBSERVE_SEL_FS_J; | |
| writel(val, base + UTMIP_MISC_CFG0); | |
| udelay(1); | |
| val = readl(base + UTMIP_MISC_CFG0); | |
| val |= UTMIP_DPDM_OBSERVE; | |
| writel(val, base + UTMIP_MISC_CFG0); | |
| udelay(10); | |
| } | |
| static void utmi_phy_restore_end(struct tegra_usb_phy *phy) | |
| { | |
| unsigned long val; | |
| void __iomem *base = phy->regs; | |
| val = readl(base + UTMIP_MISC_CFG0); | |
| val &= ~UTMIP_DPDM_OBSERVE; | |
| writel(val, base + UTMIP_MISC_CFG0); | |
| udelay(10); | |
| } | |
| static int ulpi_phy_power_on(struct tegra_usb_phy *phy) | |
| { | |
| int ret; | |
| unsigned long val; | |
| void __iomem *base = phy->regs; | |
| ret = gpio_direction_output(phy->reset_gpio, 0); | |
| if (ret < 0) { | |
| dev_err(phy->u_phy.dev, "gpio %d not set to 0\n", | |
| phy->reset_gpio); | |
| return ret; | |
| } | |
| msleep(5); | |
| ret = gpio_direction_output(phy->reset_gpio, 1); | |
| if (ret < 0) { | |
| dev_err(phy->u_phy.dev, "gpio %d not set to 1\n", | |
| phy->reset_gpio); | |
| return ret; | |
| } | |
| clk_prepare_enable(phy->clk); | |
| msleep(1); | |
| val = readl(base + USB_SUSP_CTRL); | |
| val |= UHSIC_RESET; | |
| writel(val, base + USB_SUSP_CTRL); | |
| val = readl(base + ULPI_TIMING_CTRL_0); | |
| val |= ULPI_OUTPUT_PINMUX_BYP | ULPI_CLKOUT_PINMUX_BYP; | |
| writel(val, base + ULPI_TIMING_CTRL_0); | |
| val = readl(base + USB_SUSP_CTRL); | |
| val |= ULPI_PHY_ENABLE; | |
| writel(val, base + USB_SUSP_CTRL); | |
| val = 0; | |
| writel(val, base + ULPI_TIMING_CTRL_1); | |
| val |= ULPI_DATA_TRIMMER_SEL(4); | |
| val |= ULPI_STPDIRNXT_TRIMMER_SEL(4); | |
| val |= ULPI_DIR_TRIMMER_SEL(4); | |
| writel(val, base + ULPI_TIMING_CTRL_1); | |
| udelay(10); | |
| val |= ULPI_DATA_TRIMMER_LOAD; | |
| val |= ULPI_STPDIRNXT_TRIMMER_LOAD; | |
| val |= ULPI_DIR_TRIMMER_LOAD; | |
| writel(val, base + ULPI_TIMING_CTRL_1); | |
| /* Fix VbusInvalid due to floating VBUS */ | |
| ret = usb_phy_io_write(phy->ulpi, 0x40, 0x08); | |
| if (ret) { | |
| pr_err("%s: ulpi write failed\n", __func__); | |
| return ret; | |
| } | |
| ret = usb_phy_io_write(phy->ulpi, 0x80, 0x0B); | |
| if (ret) { | |
| pr_err("%s: ulpi write failed\n", __func__); | |
| return ret; | |
| } | |
| val = readl(base + USB_SUSP_CTRL); | |
| val |= USB_SUSP_CLR; | |
| writel(val, base + USB_SUSP_CTRL); | |
| udelay(100); | |
| val = readl(base + USB_SUSP_CTRL); | |
| val &= ~USB_SUSP_CLR; | |
| writel(val, base + USB_SUSP_CTRL); | |
| return 0; | |
| } | |
| static int ulpi_phy_power_off(struct tegra_usb_phy *phy) | |
| { | |
| clk_disable(phy->clk); | |
| return gpio_direction_output(phy->reset_gpio, 0); | |
| } | |
| static void tegra_usb_phy_close(struct usb_phy *x) | |
| { | |
| struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); | |
| if (!IS_ERR(phy->vbus)) | |
| regulator_disable(phy->vbus); | |
| clk_disable_unprepare(phy->pll_u); | |
| } | |
| static int tegra_usb_phy_power_on(struct tegra_usb_phy *phy) | |
| { | |
| if (phy->is_ulpi_phy) | |
| return ulpi_phy_power_on(phy); | |
| else | |
| return utmi_phy_power_on(phy); | |
| } | |
| static int tegra_usb_phy_power_off(struct tegra_usb_phy *phy) | |
| { | |
| if (phy->is_ulpi_phy) | |
| return ulpi_phy_power_off(phy); | |
| else | |
| return utmi_phy_power_off(phy); | |
| } | |
| static int tegra_usb_phy_suspend(struct usb_phy *x, int suspend) | |
| { | |
| struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); | |
| if (suspend) | |
| return tegra_usb_phy_power_off(phy); | |
| else | |
| return tegra_usb_phy_power_on(phy); | |
| } | |
| static int ulpi_open(struct tegra_usb_phy *phy) | |
| { | |
| int err; | |
| phy->clk = devm_clk_get(phy->u_phy.dev, "ulpi-link"); | |
| if (IS_ERR(phy->clk)) { | |
| pr_err("%s: can't get ulpi clock\n", __func__); | |
| return PTR_ERR(phy->clk); | |
| } | |
| err = devm_gpio_request(phy->u_phy.dev, phy->reset_gpio, | |
| "ulpi_phy_reset_b"); | |
| if (err < 0) { | |
| dev_err(phy->u_phy.dev, "request failed for gpio: %d\n", | |
| phy->reset_gpio); | |
| return err; | |
| } | |
| err = gpio_direction_output(phy->reset_gpio, 0); | |
| if (err < 0) { | |
| dev_err(phy->u_phy.dev, "gpio %d direction not set to output\n", | |
| phy->reset_gpio); | |
| return err; | |
| } | |
| phy->ulpi = otg_ulpi_create(&ulpi_viewport_access_ops, 0); | |
| if (!phy->ulpi) { | |
| dev_err(phy->u_phy.dev, "otg_ulpi_create returned NULL\n"); | |
| err = -ENOMEM; | |
| return err; | |
| } | |
| phy->ulpi->io_priv = phy->regs + ULPI_VIEWPORT; | |
| return 0; | |
| } | |
| static int tegra_usb_phy_init(struct tegra_usb_phy *phy) | |
| { | |
| unsigned long parent_rate; | |
| int i; | |
| int err; | |
| phy->pll_u = devm_clk_get(phy->u_phy.dev, "pll_u"); | |
| if (IS_ERR(phy->pll_u)) { | |
| pr_err("Can't get pll_u clock\n"); | |
| return PTR_ERR(phy->pll_u); | |
| } | |
| err = clk_prepare_enable(phy->pll_u); | |
| if (err) | |
| return err; | |
| parent_rate = clk_get_rate(clk_get_parent(phy->pll_u)); | |
| for (i = 0; i < ARRAY_SIZE(tegra_freq_table); i++) { | |
| if (tegra_freq_table[i].freq == parent_rate) { | |
| phy->freq = &tegra_freq_table[i]; | |
| break; | |
| } | |
| } | |
| if (!phy->freq) { | |
| pr_err("invalid pll_u parent rate %ld\n", parent_rate); | |
| err = -EINVAL; | |
| goto fail; | |
| } | |
| if (!IS_ERR(phy->vbus)) { | |
| err = regulator_enable(phy->vbus); | |
| if (err) { | |
| dev_err(phy->u_phy.dev, | |
| "failed to enable usb vbus regulator: %d\n", | |
| err); | |
| goto fail; | |
| } | |
| } | |
| if (phy->is_ulpi_phy) | |
| err = ulpi_open(phy); | |
| else | |
| err = utmip_pad_open(phy); | |
| if (err < 0) | |
| goto fail; | |
| return 0; | |
| fail: | |
| clk_disable_unprepare(phy->pll_u); | |
| return err; | |
| } | |
| void tegra_usb_phy_preresume(struct usb_phy *x) | |
| { | |
| struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); | |
| if (!phy->is_ulpi_phy) | |
| utmi_phy_preresume(phy); | |
| } | |
| EXPORT_SYMBOL_GPL(tegra_usb_phy_preresume); | |
| void tegra_usb_phy_postresume(struct usb_phy *x) | |
| { | |
| struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); | |
| if (!phy->is_ulpi_phy) | |
| utmi_phy_postresume(phy); | |
| } | |
| EXPORT_SYMBOL_GPL(tegra_usb_phy_postresume); | |
| void tegra_ehci_phy_restore_start(struct usb_phy *x, | |
| enum tegra_usb_phy_port_speed port_speed) | |
| { | |
| struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); | |
| if (!phy->is_ulpi_phy) | |
| utmi_phy_restore_start(phy, port_speed); | |
| } | |
| EXPORT_SYMBOL_GPL(tegra_ehci_phy_restore_start); | |
| void tegra_ehci_phy_restore_end(struct usb_phy *x) | |
| { | |
| struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); | |
| if (!phy->is_ulpi_phy) | |
| utmi_phy_restore_end(phy); | |
| } | |
| EXPORT_SYMBOL_GPL(tegra_ehci_phy_restore_end); | |
| static int read_utmi_param(struct platform_device *pdev, const char *param, | |
| u8 *dest) | |
| { | |
| u32 value; | |
| int err = of_property_read_u32(pdev->dev.of_node, param, &value); | |
| *dest = (u8)value; | |
| if (err < 0) | |
| dev_err(&pdev->dev, "Failed to read USB UTMI parameter %s: %d\n", | |
| param, err); | |
| return err; | |
| } | |
| static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy, | |
| struct platform_device *pdev) | |
| { | |
| struct resource *res; | |
| int err; | |
| struct tegra_utmip_config *config; | |
| tegra_phy->is_ulpi_phy = false; | |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 1); | |
| if (!res) { | |
| dev_err(&pdev->dev, "Failed to get UTMI Pad regs\n"); | |
| return -ENXIO; | |
| } | |
| tegra_phy->pad_regs = devm_ioremap(&pdev->dev, res->start, | |
| resource_size(res)); | |
| if (!tegra_phy->regs) { | |
| dev_err(&pdev->dev, "Failed to remap UTMI Pad regs\n"); | |
| return -ENOMEM; | |
| } | |
| tegra_phy->config = devm_kzalloc(&pdev->dev, | |
| sizeof(*tegra_phy->config), GFP_KERNEL); | |
| if (!tegra_phy->config) { | |
| dev_err(&pdev->dev, | |
| "unable to allocate memory for USB UTMIP config\n"); | |
| return -ENOMEM; | |
| } | |
| config = tegra_phy->config; | |
| err = read_utmi_param(pdev, "nvidia,hssync-start-delay", | |
| &config->hssync_start_delay); | |
| if (err < 0) | |
| return err; | |
| err = read_utmi_param(pdev, "nvidia,elastic-limit", | |
| &config->elastic_limit); | |
| if (err < 0) | |
| return err; | |
| err = read_utmi_param(pdev, "nvidia,idle-wait-delay", | |
| &config->idle_wait_delay); | |
| if (err < 0) | |
| return err; | |
| err = read_utmi_param(pdev, "nvidia,term-range-adj", | |
| &config->term_range_adj); | |
| if (err < 0) | |
| return err; | |
| err = read_utmi_param(pdev, "nvidia,xcvr-lsfslew", | |
| &config->xcvr_lsfslew); | |
| if (err < 0) | |
| return err; | |
| err = read_utmi_param(pdev, "nvidia,xcvr-lsrslew", | |
| &config->xcvr_lsrslew); | |
| if (err < 0) | |
| return err; | |
| if (tegra_phy->soc_config->requires_extra_tuning_parameters) { | |
| err = read_utmi_param(pdev, "nvidia,xcvr-hsslew", | |
| &config->xcvr_hsslew); | |
| if (err < 0) | |
| return err; | |
| err = read_utmi_param(pdev, "nvidia,hssquelch-level", | |
| &config->hssquelch_level); | |
| if (err < 0) | |
| return err; | |
| err = read_utmi_param(pdev, "nvidia,hsdiscon-level", | |
| &config->hsdiscon_level); | |
| if (err < 0) | |
| return err; | |
| } | |
| config->xcvr_setup_use_fuses = of_property_read_bool( | |
| pdev->dev.of_node, "nvidia,xcvr-setup-use-fuses"); | |
| if (!config->xcvr_setup_use_fuses) { | |
| err = read_utmi_param(pdev, "nvidia,xcvr-setup", | |
| &config->xcvr_setup); | |
| if (err < 0) | |
| return err; | |
| } | |
| return 0; | |
| } | |
| static const struct tegra_phy_soc_config tegra20_soc_config = { | |
| .utmi_pll_config_in_car_module = false, | |
| .has_hostpc = false, | |
| .requires_usbmode_setup = false, | |
| .requires_extra_tuning_parameters = false, | |
| }; | |
| static const struct tegra_phy_soc_config tegra30_soc_config = { | |
| .utmi_pll_config_in_car_module = true, | |
| .has_hostpc = true, | |
| .requires_usbmode_setup = true, | |
| .requires_extra_tuning_parameters = true, | |
| }; | |
| static struct of_device_id tegra_usb_phy_id_table[] = { | |
| { .compatible = "nvidia,tegra30-usb-phy", .data = &tegra30_soc_config }, | |
| { .compatible = "nvidia,tegra20-usb-phy", .data = &tegra20_soc_config }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(of, tegra_usb_phy_id_table); | |
| static int tegra_usb_phy_probe(struct platform_device *pdev) | |
| { | |
| const struct of_device_id *match; | |
| struct resource *res; | |
| struct tegra_usb_phy *tegra_phy = NULL; | |
| struct device_node *np = pdev->dev.of_node; | |
| enum usb_phy_interface phy_type; | |
| int err; | |
| tegra_phy = devm_kzalloc(&pdev->dev, sizeof(*tegra_phy), GFP_KERNEL); | |
| if (!tegra_phy) { | |
| dev_err(&pdev->dev, "unable to allocate memory for USB2 PHY\n"); | |
| return -ENOMEM; | |
| } | |
| match = of_match_device(tegra_usb_phy_id_table, &pdev->dev); | |
| if (!match) { | |
| dev_err(&pdev->dev, "Error: No device match found\n"); | |
| return -ENODEV; | |
| } | |
| tegra_phy->soc_config = match->data; | |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
| if (!res) { | |
| dev_err(&pdev->dev, "Failed to get I/O memory\n"); | |
| return -ENXIO; | |
| } | |
| tegra_phy->regs = devm_ioremap(&pdev->dev, res->start, | |
| resource_size(res)); | |
| if (!tegra_phy->regs) { | |
| dev_err(&pdev->dev, "Failed to remap I/O memory\n"); | |
| return -ENOMEM; | |
| } | |
| tegra_phy->is_legacy_phy = | |
| of_property_read_bool(np, "nvidia,has-legacy-mode"); | |
| phy_type = of_usb_get_phy_mode(np); | |
| switch (phy_type) { | |
| case USBPHY_INTERFACE_MODE_UTMI: | |
| err = utmi_phy_probe(tegra_phy, pdev); | |
| if (err < 0) | |
| return err; | |
| break; | |
| case USBPHY_INTERFACE_MODE_ULPI: | |
| tegra_phy->is_ulpi_phy = true; | |
| tegra_phy->reset_gpio = | |
| of_get_named_gpio(np, "nvidia,phy-reset-gpio", 0); | |
| if (!gpio_is_valid(tegra_phy->reset_gpio)) { | |
| dev_err(&pdev->dev, "invalid gpio: %d\n", | |
| tegra_phy->reset_gpio); | |
| return tegra_phy->reset_gpio; | |
| } | |
| tegra_phy->config = NULL; | |
| break; | |
| default: | |
| dev_err(&pdev->dev, "phy_type is invalid or unsupported\n"); | |
| return -EINVAL; | |
| } | |
| if (of_find_property(np, "dr_mode", NULL)) | |
| tegra_phy->mode = of_usb_get_dr_mode(np); | |
| else | |
| tegra_phy->mode = USB_DR_MODE_HOST; | |
| if (tegra_phy->mode == USB_DR_MODE_UNKNOWN) { | |
| dev_err(&pdev->dev, "dr_mode is invalid\n"); | |
| return -EINVAL; | |
| } | |
| /* On some boards, the VBUS regulator doesn't need to be controlled */ | |
| if (of_find_property(np, "vbus-supply", NULL)) { | |
| tegra_phy->vbus = devm_regulator_get(&pdev->dev, "vbus"); | |
| if (IS_ERR(tegra_phy->vbus)) | |
| return PTR_ERR(tegra_phy->vbus); | |
| } else { | |
| dev_notice(&pdev->dev, "no vbus regulator"); | |
| tegra_phy->vbus = ERR_PTR(-ENODEV); | |
| } | |
| tegra_phy->u_phy.dev = &pdev->dev; | |
| err = tegra_usb_phy_init(tegra_phy); | |
| if (err < 0) | |
| return err; | |
| tegra_phy->u_phy.shutdown = tegra_usb_phy_close; | |
| tegra_phy->u_phy.set_suspend = tegra_usb_phy_suspend; | |
| platform_set_drvdata(pdev, tegra_phy); | |
| err = usb_add_phy_dev(&tegra_phy->u_phy); | |
| if (err < 0) { | |
| tegra_usb_phy_close(&tegra_phy->u_phy); | |
| return err; | |
| } | |
| return 0; | |
| } | |
| static int tegra_usb_phy_remove(struct platform_device *pdev) | |
| { | |
| struct tegra_usb_phy *tegra_phy = platform_get_drvdata(pdev); | |
| usb_remove_phy(&tegra_phy->u_phy); | |
| return 0; | |
| } | |
| static struct platform_driver tegra_usb_phy_driver = { | |
| .probe = tegra_usb_phy_probe, | |
| .remove = tegra_usb_phy_remove, | |
| .driver = { | |
| .name = "tegra-phy", | |
| .owner = THIS_MODULE, | |
| .of_match_table = of_match_ptr(tegra_usb_phy_id_table), | |
| }, | |
| }; | |
| module_platform_driver(tegra_usb_phy_driver); | |
| MODULE_DESCRIPTION("Tegra USB PHY driver"); | |
| MODULE_LICENSE("GPL v2"); |