| # |
| # USB Core configuration |
| # |
| config USB_ANNOUNCE_NEW_DEVICES |
| bool "USB announce new devices" |
| help |
| Say Y here if you want the USB core to always announce the |
| idVendor, idProduct, Manufacturer, Product, and SerialNumber |
| strings for every new USB device to the syslog. This option is |
| usually used by distro vendors to help with debugging and to |
| let users know what specific device was added to the machine |
| in what location. |
| |
| If you do not want this kind of information sent to the system |
| log, or have any doubts about this, say N here. |
| |
| comment "Miscellaneous USB options" |
| |
| config USB_DEFAULT_PERSIST |
| bool "Enable USB persist by default" |
| default y |
| help |
| Say N here if you don't want USB power session persistence |
| enabled by default. If you say N it will make suspended USB |
| devices that lose power get reenumerated as if they had been |
| unplugged, causing any mounted filesystems to be lost. The |
| persist feature can still be enabled for individual devices |
| through the power/persist sysfs node. See |
| Documentation/usb/persist.txt for more info. |
| |
| If you have any questions about this, say Y here, only say N |
| if you know exactly what you are doing. |
| |
| config USB_DYNAMIC_MINORS |
| bool "Dynamic USB minor allocation" |
| help |
| If you say Y here, the USB subsystem will use dynamic minor |
| allocation for any device that uses the USB major number. |
| This means that you can have more than 16 of a single type |
| of device (like USB printers). |
| |
| If you are unsure about this, say N here. |
| |
| config USB_OTG |
| bool "OTG support" |
| depends on PM |
| default n |
| help |
| The most notable feature of USB OTG is support for a |
| "Dual-Role" device, which can act as either a device |
| or a host. The initial role is decided by the type of |
| plug inserted and can be changed later when two dual |
| role devices talk to each other. |
| |
| Select this only if your board has Mini-AB/Micro-AB |
| connector. |
| |
| config USB_OTG_WHITELIST |
| bool "Rely on OTG and EH Targeted Peripherals List" |
| depends on USB |
| help |
| If you say Y here, the "otg_whitelist.h" file will be used as a |
| product whitelist, so USB peripherals not listed there will be |
| rejected during enumeration. This behavior is required by the |
| USB OTG and EH specification for all devices not on your product's |
| "Targeted Peripherals List". "Embedded Hosts" are likewise |
| allowed to support only a limited number of peripherals. |
| |
| config USB_OTG_BLACKLIST_HUB |
| bool "Disable external hubs" |
| depends on USB_OTG || EXPERT |
| help |
| If you say Y here, then Linux will refuse to enumerate |
| external hubs. OTG hosts are allowed to reduce hardware |
| and software costs by not supporting external hubs. So |
| are "Embedded Hosts" that don't offer OTG support. |
| |
| config USB_OTG_FSM |
| tristate "USB 2.0 OTG FSM implementation" |
| depends on USB && USB_OTG |
| select USB_PHY |
| help |
| Implements OTG Finite State Machine as specified in On-The-Go |
| and Embedded Host Supplement to the USB Revision 2.0 Specification. |
| |
| config USB_ULPI_BUS |
| tristate "USB ULPI PHY interface support" |
| depends on USB_SUPPORT |
| help |
| UTMI+ Low Pin Interface (ULPI) is specification for a commonly used |
| USB 2.0 PHY interface. The ULPI specification defines a standard set |
| of registers that can be used to detect the vendor and product which |
| allows ULPI to be handled as a bus. This module is the driver for that |
| bus. |
| |
| The ULPI interfaces (the buses) are registered by the drivers for USB |
| controllers which support ULPI register access and have ULPI PHY |
| attached to them. The ULPI PHY drivers themselves are normal PHY |
| drivers. |
| |
| ULPI PHYs provide often functions such as ADP sensing/probing (OTG |
| protocol) and USB charger detection. |
| |
| To compile this driver as a module, choose M here: the module will |
| be called ulpi. |
