Documentation/fb/udlfb.txt - arm/linux - Git at Google


 What is udlfb?
 ===============

 This is a driver for DisplayLink USB 2.0 era graphics chips.

 DisplayLink chips provide simple hline/blit operations with some compression,
 pairing that with a hardware framebuffer (16MB) on the other end of the
 USB wire.  That hardware framebuffer is able to drive the VGA, DVI, or HDMI
 monitor with no CPU involvement until a pixel has to change.

 The CPU or other local resource does all the rendering; optionally compares the
 result with a local shadow of the remote hardware framebuffer to identify
 the minimal set of pixels that have changed; and compresses and sends those
 pixels line-by-line via USB bulk transfers.

 Because of the efficiency of bulk transfers and a protocol on top that
 does not require any acks - the effect is very low latency that
 can support surprisingly high resolutions with good performance for
 non-gaming and non-video applications.

 Mode setting, EDID read, etc are other bulk or control transfers. Mode
 setting is very flexible - able to set nearly arbitrary modes from any timing.

 Advantages of USB graphics in general:

  * Ability to add a nearly arbitrary number of displays to any USB 2.0
    capable system. On Linux, number of displays is limited by fbdev interface
    (FB_MAX is currently 32). Of course, all USB devices on the same
    host controller share the same 480Mbs USB 2.0 interface.

 Advantages of supporting DisplayLink chips with kernel framebuffer interface:

  * The actual hardware functionality of DisplayLink chips matches nearly
    one-to-one with the fbdev interface, making the driver quite small and
    tight relative to the functionality it provides.
  * X servers and other applications can use the standard fbdev interface
    from user mode to talk to the device, without needing to know anything
    about USB or DisplayLink's protocol at all. A "displaylink" X driver
    and a slightly modified "fbdev" X driver are among those that already do.

 Disadvantages:

  * Fbdev's mmap interface assumes a real hardware framebuffer is mapped.
    In the case of USB graphics, it is just an allocated (virtual) buffer.
    Writes need to be detected and encoded into USB bulk transfers by the CPU.
    Accurate damage/changed area notifications work around this problem.
    In the future, hopefully fbdev will be enhanced with an small standard
    interface to allow mmap clients to report damage, for the benefit
    of virtual or remote framebuffers.
  * Fbdev does not arbitrate client ownership of the framebuffer well.
  * Fbcon assumes the first framebuffer it finds should be consumed for console.
  * It's not clear what the future of fbdev is, given the rise of KMS/DRM.

 How to use it?
 ==============

 Udlfb, when loaded as a module, will match against all USB 2.0 generation
 DisplayLink chips (Alex and Ollie family). It will then attempt to read the EDID
 of the monitor, and set the best common mode between the DisplayLink device
 and the monitor's capabilities.

 If the DisplayLink device is successful, it will paint a "green screen" which
 means that from a hardware and fbdev software perspective, everything is good.

 At that point, a /dev/fb? interface will be present for user-mode applications
 to open and begin writing to the framebuffer of the DisplayLink device using
 standard fbdev calls.  Note that if mmap() is used, by default the user mode
 application must send down damage notifications to trigger repaints of the
 changed regions.  Alternatively, udlfb can be recompiled with experimental
 defio support enabled, to support a page-fault based detection mechanism
 that can work without explicit notification.

 The most common client of udlfb is xf86-video-displaylink or a modified
 xf86-video-fbdev X server. These servers have no real DisplayLink specific
 code. They write to the standard framebuffer interface and rely on udlfb
 to do its thing.  The one extra feature they have is the ability to report
 rectangles from the X DAMAGE protocol extension down to udlfb via udlfb's
 damage interface (which will hopefully be standardized for all virtual
 framebuffers that need damage info). These damage notifications allow
 udlfb to efficiently process the changed pixels.

 Module Options
 ==============

 Special configuration for udlfb is usually unnecessary. There are a few
 options, however.

 From the command line, pass options to modprobe
 modprobe udlfb fb_defio=0 console=1 shadow=1

 Or modify options on the fly at /sys/module/udlfb/parameters directory via
 sudo nano fb_defio
 change the parameter in place, and save the file.

 Unplug/replug USB device to apply with new settings

 Or for permanent option, create file like /etc/modprobe.d/udlfb.conf with text
 options udlfb fb_defio=0 console=1 shadow=1

 Accepted boolean options:

 fb_defio	Make use of the fb_defio (CONFIG_FB_DEFERRED_IO) kernel
 		module to track changed areas of the framebuffer by page faults.
 		Standard fbdev applications that use mmap but that do not
 		report damage, should be able to work with this enabled.
 		Disable when running with X server that supports reporting
 		changed regions via ioctl, as this method is simpler,
 		more stable, and higher performance.
 		default: fb_defio=1

 console	Allow fbcon to attach to udlfb provided framebuffers.
 		Can be disabled if fbcon and other clients
 		(e.g. X with --shared-vt) are in conflict.
 		default: console=1

 shadow		Allocate a 2nd framebuffer to shadow what's currently across
 		the USB bus in device memory. If any pixels are unchanged,
 		do not transmit. Spends host memory to save USB transfers.
 		Enabled by default. Only disable on very low memory systems.
 		default: shadow=1

 Sysfs Attributes
 ================

 Udlfb creates several files in /sys/class/graphics/fb?
 Where ? is the sequential framebuffer id of the particular DisplayLink device

 edid	       		If a valid EDID blob is written to this file (typically
 			by a udev rule), then udlfb will use this EDID as a
 			backup in case reading the actual EDID of the monitor
 			attached to the DisplayLink device fails. This is
 			especially useful for fixed panels, etc. that cannot
 			communicate their capabilities via EDID. Reading
 			this file returns the current EDID of the attached
 			monitor (or last backup value written). This is
 			useful to get the EDID of the attached monitor,
 			which can be passed to utilities like parse-edid.

 metrics_bytes_rendered	32-bit count of pixel bytes rendered

 metrics_bytes_identical 32-bit count of how many of those bytes were found to be
 			unchanged, based on a shadow framebuffer check

 metrics_bytes_sent	32-bit count of how many bytes were transferred over
 			USB to communicate the resulting changed pixels to the
 			hardware. Includes compression and protocol overhead

 metrics_cpu_kcycles_used 32-bit count of CPU cycles used in processing the
 			above pixels (in thousands of cycles).

 metrics_reset		Write-only. Any write to this file resets all metrics
 			above to zero.  Note that the 32-bit counters above
 			roll over very quickly. To get reliable results, design
 			performance tests to start and finish in a very short
 			period of time (one minute or less is safe).

 --
 Bernie Thompson <bernie@plugable.com>

	What is udlfb?
	===============

	This is a driver for DisplayLink USB 2.0 era graphics chips.

	DisplayLink chips provide simple hline/blit operations with some compression,
	pairing that with a hardware framebuffer (16MB) on the other end of the
	USB wire. That hardware framebuffer is able to drive the VGA, DVI, or HDMI
	monitor with no CPU involvement until a pixel has to change.

	The CPU or other local resource does all the rendering; optionally compares the
	result with a local shadow of the remote hardware framebuffer to identify
	the minimal set of pixels that have changed; and compresses and sends those
	pixels line-by-line via USB bulk transfers.

	Because of the efficiency of bulk transfers and a protocol on top that
	does not require any acks - the effect is very low latency that
	can support surprisingly high resolutions with good performance for
	non-gaming and non-video applications.

	Mode setting, EDID read, etc are other bulk or control transfers. Mode
	setting is very flexible - able to set nearly arbitrary modes from any timing.

	Advantages of USB graphics in general:

	* Ability to add a nearly arbitrary number of displays to any USB 2.0
	capable system. On Linux, number of displays is limited by fbdev interface
	(FB_MAX is currently 32). Of course, all USB devices on the same
	host controller share the same 480Mbs USB 2.0 interface.

	Advantages of supporting DisplayLink chips with kernel framebuffer interface:

	* The actual hardware functionality of DisplayLink chips matches nearly
	one-to-one with the fbdev interface, making the driver quite small and
	tight relative to the functionality it provides.
	* X servers and other applications can use the standard fbdev interface
	from user mode to talk to the device, without needing to know anything
	about USB or DisplayLink's protocol at all. A "displaylink" X driver
	and a slightly modified "fbdev" X driver are among those that already do.

	Disadvantages:

	* Fbdev's mmap interface assumes a real hardware framebuffer is mapped.
	In the case of USB graphics, it is just an allocated (virtual) buffer.
	Writes need to be detected and encoded into USB bulk transfers by the CPU.
	Accurate damage/changed area notifications work around this problem.
	In the future, hopefully fbdev will be enhanced with an small standard
	interface to allow mmap clients to report damage, for the benefit
	of virtual or remote framebuffers.
	* Fbdev does not arbitrate client ownership of the framebuffer well.
	* Fbcon assumes the first framebuffer it finds should be consumed for console.
	* It's not clear what the future of fbdev is, given the rise of KMS/DRM.

	How to use it?
	==============

	Udlfb, when loaded as a module, will match against all USB 2.0 generation
	DisplayLink chips (Alex and Ollie family). It will then attempt to read the EDID
	of the monitor, and set the best common mode between the DisplayLink device
	and the monitor's capabilities.

	If the DisplayLink device is successful, it will paint a "green screen" which
	means that from a hardware and fbdev software perspective, everything is good.

	At that point, a /dev/fb? interface will be present for user-mode applications
	to open and begin writing to the framebuffer of the DisplayLink device using
	standard fbdev calls. Note that if mmap() is used, by default the user mode
	application must send down damage notifications to trigger repaints of the
	changed regions. Alternatively, udlfb can be recompiled with experimental
	defio support enabled, to support a page-fault based detection mechanism
	that can work without explicit notification.

	The most common client of udlfb is xf86-video-displaylink or a modified
	xf86-video-fbdev X server. These servers have no real DisplayLink specific
	code. They write to the standard framebuffer interface and rely on udlfb
	to do its thing. The one extra feature they have is the ability to report
	rectangles from the X DAMAGE protocol extension down to udlfb via udlfb's
	damage interface (which will hopefully be standardized for all virtual
	framebuffers that need damage info). These damage notifications allow
	udlfb to efficiently process the changed pixels.

	Module Options
	==============

	Special configuration for udlfb is usually unnecessary. There are a few
	options, however.

	From the command line, pass options to modprobe
	modprobe udlfb fb_defio=0 console=1 shadow=1

	Or modify options on the fly at /sys/module/udlfb/parameters directory via
	sudo nano fb_defio
	change the parameter in place, and save the file.

	Unplug/replug USB device to apply with new settings

	Or for permanent option, create file like /etc/modprobe.d/udlfb.conf with text
	options udlfb fb_defio=0 console=1 shadow=1

	Accepted boolean options:

	fb_defio Make use of the fb_defio (CONFIG_FB_DEFERRED_IO) kernel
	module to track changed areas of the framebuffer by page faults.
	Standard fbdev applications that use mmap but that do not
	report damage, should be able to work with this enabled.
	Disable when running with X server that supports reporting
	changed regions via ioctl, as this method is simpler,
	more stable, and higher performance.
	default: fb_defio=1

	console Allow fbcon to attach to udlfb provided framebuffers.
	Can be disabled if fbcon and other clients
	(e.g. X with --shared-vt) are in conflict.
	default: console=1

	shadow Allocate a 2nd framebuffer to shadow what's currently across
	the USB bus in device memory. If any pixels are unchanged,
	do not transmit. Spends host memory to save USB transfers.
	Enabled by default. Only disable on very low memory systems.
	default: shadow=1

	Sysfs Attributes
	================

	Udlfb creates several files in /sys/class/graphics/fb?
	Where ? is the sequential framebuffer id of the particular DisplayLink device

	edid If a valid EDID blob is written to this file (typically
	by a udev rule), then udlfb will use this EDID as a
	backup in case reading the actual EDID of the monitor
	attached to the DisplayLink device fails. This is
	especially useful for fixed panels, etc. that cannot
	communicate their capabilities via EDID. Reading
	this file returns the current EDID of the attached
	monitor (or last backup value written). This is
	useful to get the EDID of the attached monitor,
	which can be passed to utilities like parse-edid.

	metrics_bytes_rendered 32-bit count of pixel bytes rendered

	metrics_bytes_identical 32-bit count of how many of those bytes were found to be
	unchanged, based on a shadow framebuffer check

	metrics_bytes_sent 32-bit count of how many bytes were transferred over
	USB to communicate the resulting changed pixels to the
	hardware. Includes compression and protocol overhead

	metrics_cpu_kcycles_used 32-bit count of CPU cycles used in processing the
	above pixels (in thousands of cycles).

	metrics_reset Write-only. Any write to this file resets all metrics
	above to zero. Note that the 32-bit counters above
	roll over very quickly. To get reliable results, design
	performance tests to start and finish in a very short
	period of time (one minute or less is safe).

	--
	Bernie Thompson <bernie@plugable.com>