| /* | |
| * Driver for CSR SiRFprimaII onboard UARTs. | |
| * | |
| * Copyright (c) 2011 Cambridge Silicon Radio Limited, a CSR plc group company. | |
| * | |
| * Licensed under GPLv2 or later. | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/ioport.h> | |
| #include <linux/platform_device.h> | |
| #include <linux/init.h> | |
| #include <linux/sysrq.h> | |
| #include <linux/console.h> | |
| #include <linux/tty.h> | |
| #include <linux/tty_flip.h> | |
| #include <linux/serial_core.h> | |
| #include <linux/serial.h> | |
| #include <linux/clk.h> | |
| #include <linux/of.h> | |
| #include <linux/slab.h> | |
| #include <linux/io.h> | |
| #include <linux/of_gpio.h> | |
| #include <linux/dmaengine.h> | |
| #include <linux/dma-direction.h> | |
| #include <linux/dma-mapping.h> | |
| #include <asm/irq.h> | |
| #include <asm/mach/irq.h> | |
| #include "sirfsoc_uart.h" | |
| static unsigned int | |
| sirfsoc_uart_pio_tx_chars(struct sirfsoc_uart_port *sirfport, int count); | |
| static unsigned int | |
| sirfsoc_uart_pio_rx_chars(struct uart_port *port, unsigned int max_rx_count); | |
| static struct uart_driver sirfsoc_uart_drv; | |
| static void sirfsoc_uart_tx_dma_complete_callback(void *param); | |
| static const struct sirfsoc_baudrate_to_regv baudrate_to_regv[] = { | |
| {4000000, 2359296}, | |
| {3500000, 1310721}, | |
| {3000000, 1572865}, | |
| {2500000, 1245186}, | |
| {2000000, 1572866}, | |
| {1500000, 1245188}, | |
| {1152000, 1638404}, | |
| {1000000, 1572869}, | |
| {921600, 1114120}, | |
| {576000, 1245196}, | |
| {500000, 1245198}, | |
| {460800, 1572876}, | |
| {230400, 1310750}, | |
| {115200, 1310781}, | |
| {57600, 1310843}, | |
| {38400, 1114328}, | |
| {19200, 1114545}, | |
| {9600, 1114979}, | |
| }; | |
| static struct sirfsoc_uart_port *sirf_ports[SIRFSOC_UART_NR]; | |
| static inline struct sirfsoc_uart_port *to_sirfport(struct uart_port *port) | |
| { | |
| return container_of(port, struct sirfsoc_uart_port, port); | |
| } | |
| static inline unsigned int sirfsoc_uart_tx_empty(struct uart_port *port) | |
| { | |
| unsigned long reg; | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_fifo_status *ufifo_st = &sirfport->uart_reg->fifo_status; | |
| reg = rd_regl(port, ureg->sirfsoc_tx_fifo_status); | |
| return (reg & ufifo_st->ff_empty(port)) ? TIOCSER_TEMT : 0; | |
| } | |
| static unsigned int sirfsoc_uart_get_mctrl(struct uart_port *port) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| if (!sirfport->hw_flow_ctrl || !sirfport->ms_enabled) | |
| goto cts_asserted; | |
| if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) { | |
| if (!(rd_regl(port, ureg->sirfsoc_afc_ctrl) & | |
| SIRFUART_AFC_CTS_STATUS)) | |
| goto cts_asserted; | |
| else | |
| goto cts_deasserted; | |
| } else { | |
| if (!gpio_get_value(sirfport->cts_gpio)) | |
| goto cts_asserted; | |
| else | |
| goto cts_deasserted; | |
| } | |
| cts_deasserted: | |
| return TIOCM_CAR | TIOCM_DSR; | |
| cts_asserted: | |
| return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS; | |
| } | |
| static void sirfsoc_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| unsigned int assert = mctrl & TIOCM_RTS; | |
| unsigned int val = assert ? SIRFUART_AFC_CTRL_RX_THD : 0x0; | |
| unsigned int current_val; | |
| if (mctrl & TIOCM_LOOP) { | |
| if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) | |
| wr_regl(port, ureg->sirfsoc_line_ctrl, | |
| rd_regl(port, ureg->sirfsoc_line_ctrl) | | |
| SIRFUART_LOOP_BACK); | |
| else | |
| wr_regl(port, ureg->sirfsoc_mode1, | |
| rd_regl(port, ureg->sirfsoc_mode1) | | |
| SIRFSOC_USP_LOOP_BACK_CTRL); | |
| } else { | |
| if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) | |
| wr_regl(port, ureg->sirfsoc_line_ctrl, | |
| rd_regl(port, ureg->sirfsoc_line_ctrl) & | |
| ~SIRFUART_LOOP_BACK); | |
| else | |
| wr_regl(port, ureg->sirfsoc_mode1, | |
| rd_regl(port, ureg->sirfsoc_mode1) & | |
| ~SIRFSOC_USP_LOOP_BACK_CTRL); | |
| } | |
| if (!sirfport->hw_flow_ctrl || !sirfport->ms_enabled) | |
| return; | |
| if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) { | |
| current_val = rd_regl(port, ureg->sirfsoc_afc_ctrl) & ~0xFF; | |
| val |= current_val; | |
| wr_regl(port, ureg->sirfsoc_afc_ctrl, val); | |
| } else { | |
| if (!val) | |
| gpio_set_value(sirfport->rts_gpio, 1); | |
| else | |
| gpio_set_value(sirfport->rts_gpio, 0); | |
| } | |
| } | |
| static void sirfsoc_uart_stop_tx(struct uart_port *port) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; | |
| if (sirfport->tx_dma_chan) { | |
| if (sirfport->tx_dma_state == TX_DMA_RUNNING) { | |
| dmaengine_pause(sirfport->tx_dma_chan); | |
| sirfport->tx_dma_state = TX_DMA_PAUSE; | |
| } else { | |
| if (!sirfport->is_atlas7) | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg) & | |
| ~uint_en->sirfsoc_txfifo_empty_en); | |
| else | |
| wr_regl(port, ureg->sirfsoc_int_en_clr_reg, | |
| uint_en->sirfsoc_txfifo_empty_en); | |
| } | |
| } else { | |
| if (sirfport->uart_reg->uart_type == SIRF_USP_UART) | |
| wr_regl(port, ureg->sirfsoc_tx_rx_en, rd_regl(port, | |
| ureg->sirfsoc_tx_rx_en) & ~SIRFUART_TX_EN); | |
| if (!sirfport->is_atlas7) | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg) & | |
| ~uint_en->sirfsoc_txfifo_empty_en); | |
| else | |
| wr_regl(port, ureg->sirfsoc_int_en_clr_reg, | |
| uint_en->sirfsoc_txfifo_empty_en); | |
| } | |
| } | |
| static void sirfsoc_uart_tx_with_dma(struct sirfsoc_uart_port *sirfport) | |
| { | |
| struct uart_port *port = &sirfport->port; | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; | |
| struct circ_buf *xmit = &port->state->xmit; | |
| unsigned long tran_size; | |
| unsigned long tran_start; | |
| unsigned long pio_tx_size; | |
| tran_size = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); | |
| tran_start = (unsigned long)(xmit->buf + xmit->tail); | |
| if (uart_circ_empty(xmit) || uart_tx_stopped(port) || | |
| !tran_size) | |
| return; | |
| if (sirfport->tx_dma_state == TX_DMA_PAUSE) { | |
| dmaengine_resume(sirfport->tx_dma_chan); | |
| return; | |
| } | |
| if (sirfport->tx_dma_state == TX_DMA_RUNNING) | |
| return; | |
| if (!sirfport->is_atlas7) | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg)& | |
| ~(uint_en->sirfsoc_txfifo_empty_en)); | |
| else | |
| wr_regl(port, ureg->sirfsoc_int_en_clr_reg, | |
| uint_en->sirfsoc_txfifo_empty_en); | |
| /* | |
| * DMA requires buffer address and buffer length are both aligned with | |
| * 4 bytes, so we use PIO for | |
| * 1. if address is not aligned with 4bytes, use PIO for the first 1~3 | |
| * bytes, and move to DMA for the left part aligned with 4bytes | |
| * 2. if buffer length is not aligned with 4bytes, use DMA for aligned | |
| * part first, move to PIO for the left 1~3 bytes | |
| */ | |
| if (tran_size < 4 || BYTES_TO_ALIGN(tran_start)) { | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_op, SIRFUART_FIFO_STOP); | |
| wr_regl(port, ureg->sirfsoc_tx_dma_io_ctrl, | |
| rd_regl(port, ureg->sirfsoc_tx_dma_io_ctrl)| | |
| SIRFUART_IO_MODE); | |
| if (BYTES_TO_ALIGN(tran_start)) { | |
| pio_tx_size = sirfsoc_uart_pio_tx_chars(sirfport, | |
| BYTES_TO_ALIGN(tran_start)); | |
| tran_size -= pio_tx_size; | |
| } | |
| if (tran_size < 4) | |
| sirfsoc_uart_pio_tx_chars(sirfport, tran_size); | |
| if (!sirfport->is_atlas7) | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg)| | |
| uint_en->sirfsoc_txfifo_empty_en); | |
| else | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| uint_en->sirfsoc_txfifo_empty_en); | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_op, SIRFUART_FIFO_START); | |
| } else { | |
| /* tx transfer mode switch into dma mode */ | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_op, SIRFUART_FIFO_STOP); | |
| wr_regl(port, ureg->sirfsoc_tx_dma_io_ctrl, | |
| rd_regl(port, ureg->sirfsoc_tx_dma_io_ctrl)& | |
| ~SIRFUART_IO_MODE); | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_op, SIRFUART_FIFO_START); | |
| tran_size &= ~(0x3); | |
| sirfport->tx_dma_addr = dma_map_single(port->dev, | |
| xmit->buf + xmit->tail, | |
| tran_size, DMA_TO_DEVICE); | |
| sirfport->tx_dma_desc = dmaengine_prep_slave_single( | |
| sirfport->tx_dma_chan, sirfport->tx_dma_addr, | |
| tran_size, DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT); | |
| if (!sirfport->tx_dma_desc) { | |
| dev_err(port->dev, "DMA prep slave single fail\n"); | |
| return; | |
| } | |
| sirfport->tx_dma_desc->callback = | |
| sirfsoc_uart_tx_dma_complete_callback; | |
| sirfport->tx_dma_desc->callback_param = (void *)sirfport; | |
| sirfport->transfer_size = tran_size; | |
| dmaengine_submit(sirfport->tx_dma_desc); | |
| dma_async_issue_pending(sirfport->tx_dma_chan); | |
| sirfport->tx_dma_state = TX_DMA_RUNNING; | |
| } | |
| } | |
| static void sirfsoc_uart_start_tx(struct uart_port *port) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; | |
| if (sirfport->tx_dma_chan) | |
| sirfsoc_uart_tx_with_dma(sirfport); | |
| else { | |
| if (sirfport->uart_reg->uart_type == SIRF_USP_UART) | |
| wr_regl(port, ureg->sirfsoc_tx_rx_en, rd_regl(port, | |
| ureg->sirfsoc_tx_rx_en) | SIRFUART_TX_EN); | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_op, SIRFUART_FIFO_STOP); | |
| sirfsoc_uart_pio_tx_chars(sirfport, port->fifosize); | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_op, SIRFUART_FIFO_START); | |
| if (!sirfport->is_atlas7) | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg)| | |
| uint_en->sirfsoc_txfifo_empty_en); | |
| else | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| uint_en->sirfsoc_txfifo_empty_en); | |
| } | |
| } | |
| static void sirfsoc_uart_stop_rx(struct uart_port *port) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; | |
| wr_regl(port, ureg->sirfsoc_rx_fifo_op, 0); | |
| if (sirfport->rx_dma_chan) { | |
| if (!sirfport->is_atlas7) | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg) & | |
| ~(SIRFUART_RX_DMA_INT_EN(uint_en, | |
| sirfport->uart_reg->uart_type) | | |
| uint_en->sirfsoc_rx_done_en)); | |
| else | |
| wr_regl(port, ureg->sirfsoc_int_en_clr_reg, | |
| SIRFUART_RX_DMA_INT_EN(uint_en, | |
| sirfport->uart_reg->uart_type)| | |
| uint_en->sirfsoc_rx_done_en); | |
| dmaengine_terminate_all(sirfport->rx_dma_chan); | |
| } else { | |
| if (!sirfport->is_atlas7) | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg)& | |
| ~(SIRFUART_RX_IO_INT_EN(uint_en, | |
| sirfport->uart_reg->uart_type))); | |
| else | |
| wr_regl(port, ureg->sirfsoc_int_en_clr_reg, | |
| SIRFUART_RX_IO_INT_EN(uint_en, | |
| sirfport->uart_reg->uart_type)); | |
| } | |
| } | |
| static void sirfsoc_uart_disable_ms(struct uart_port *port) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; | |
| if (!sirfport->hw_flow_ctrl) | |
| return; | |
| sirfport->ms_enabled = false; | |
| if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) { | |
| wr_regl(port, ureg->sirfsoc_afc_ctrl, | |
| rd_regl(port, ureg->sirfsoc_afc_ctrl) & ~0x3FF); | |
| if (!sirfport->is_atlas7) | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg)& | |
| ~uint_en->sirfsoc_cts_en); | |
| else | |
| wr_regl(port, ureg->sirfsoc_int_en_clr_reg, | |
| uint_en->sirfsoc_cts_en); | |
| } else | |
| disable_irq(gpio_to_irq(sirfport->cts_gpio)); | |
| } | |
| static irqreturn_t sirfsoc_uart_usp_cts_handler(int irq, void *dev_id) | |
| { | |
| struct sirfsoc_uart_port *sirfport = (struct sirfsoc_uart_port *)dev_id; | |
| struct uart_port *port = &sirfport->port; | |
| spin_lock(&port->lock); | |
| if (gpio_is_valid(sirfport->cts_gpio) && sirfport->ms_enabled) | |
| uart_handle_cts_change(port, | |
| !gpio_get_value(sirfport->cts_gpio)); | |
| spin_unlock(&port->lock); | |
| return IRQ_HANDLED; | |
| } | |
| static void sirfsoc_uart_enable_ms(struct uart_port *port) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; | |
| if (!sirfport->hw_flow_ctrl) | |
| return; | |
| sirfport->ms_enabled = true; | |
| if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) { | |
| wr_regl(port, ureg->sirfsoc_afc_ctrl, | |
| rd_regl(port, ureg->sirfsoc_afc_ctrl) | | |
| SIRFUART_AFC_TX_EN | SIRFUART_AFC_RX_EN | | |
| SIRFUART_AFC_CTRL_RX_THD); | |
| if (!sirfport->is_atlas7) | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg) | |
| | uint_en->sirfsoc_cts_en); | |
| else | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| uint_en->sirfsoc_cts_en); | |
| } else | |
| enable_irq(gpio_to_irq(sirfport->cts_gpio)); | |
| } | |
| static void sirfsoc_uart_break_ctl(struct uart_port *port, int break_state) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) { | |
| unsigned long ulcon = rd_regl(port, ureg->sirfsoc_line_ctrl); | |
| if (break_state) | |
| ulcon |= SIRFUART_SET_BREAK; | |
| else | |
| ulcon &= ~SIRFUART_SET_BREAK; | |
| wr_regl(port, ureg->sirfsoc_line_ctrl, ulcon); | |
| } | |
| } | |
| static unsigned int | |
| sirfsoc_uart_pio_rx_chars(struct uart_port *port, unsigned int max_rx_count) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_fifo_status *ufifo_st = &sirfport->uart_reg->fifo_status; | |
| unsigned int ch, rx_count = 0; | |
| struct tty_struct *tty; | |
| tty = tty_port_tty_get(&port->state->port); | |
| if (!tty) | |
| return -ENODEV; | |
| while (!(rd_regl(port, ureg->sirfsoc_rx_fifo_status) & | |
| ufifo_st->ff_empty(port))) { | |
| ch = rd_regl(port, ureg->sirfsoc_rx_fifo_data) | | |
| SIRFUART_DUMMY_READ; | |
| if (unlikely(uart_handle_sysrq_char(port, ch))) | |
| continue; | |
| uart_insert_char(port, 0, 0, ch, TTY_NORMAL); | |
| rx_count++; | |
| if (rx_count >= max_rx_count) | |
| break; | |
| } | |
| port->icount.rx += rx_count; | |
| return rx_count; | |
| } | |
| static unsigned int | |
| sirfsoc_uart_pio_tx_chars(struct sirfsoc_uart_port *sirfport, int count) | |
| { | |
| struct uart_port *port = &sirfport->port; | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_fifo_status *ufifo_st = &sirfport->uart_reg->fifo_status; | |
| struct circ_buf *xmit = &port->state->xmit; | |
| unsigned int num_tx = 0; | |
| while (!uart_circ_empty(xmit) && | |
| !(rd_regl(port, ureg->sirfsoc_tx_fifo_status) & | |
| ufifo_st->ff_full(port)) && | |
| count--) { | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_data, | |
| xmit->buf[xmit->tail]); | |
| xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); | |
| port->icount.tx++; | |
| num_tx++; | |
| } | |
| if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) | |
| uart_write_wakeup(port); | |
| return num_tx; | |
| } | |
| static void sirfsoc_uart_tx_dma_complete_callback(void *param) | |
| { | |
| struct sirfsoc_uart_port *sirfport = (struct sirfsoc_uart_port *)param; | |
| struct uart_port *port = &sirfport->port; | |
| struct circ_buf *xmit = &port->state->xmit; | |
| unsigned long flags; | |
| spin_lock_irqsave(&port->lock, flags); | |
| xmit->tail = (xmit->tail + sirfport->transfer_size) & | |
| (UART_XMIT_SIZE - 1); | |
| port->icount.tx += sirfport->transfer_size; | |
| if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) | |
| uart_write_wakeup(port); | |
| if (sirfport->tx_dma_addr) | |
| dma_unmap_single(port->dev, sirfport->tx_dma_addr, | |
| sirfport->transfer_size, DMA_TO_DEVICE); | |
| sirfport->tx_dma_state = TX_DMA_IDLE; | |
| sirfsoc_uart_tx_with_dma(sirfport); | |
| spin_unlock_irqrestore(&port->lock, flags); | |
| } | |
| static irqreturn_t sirfsoc_uart_isr(int irq, void *dev_id) | |
| { | |
| unsigned long intr_status; | |
| unsigned long cts_status; | |
| unsigned long flag = TTY_NORMAL; | |
| struct sirfsoc_uart_port *sirfport = (struct sirfsoc_uart_port *)dev_id; | |
| struct uart_port *port = &sirfport->port; | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_fifo_status *ufifo_st = &sirfport->uart_reg->fifo_status; | |
| struct sirfsoc_int_status *uint_st = &sirfport->uart_reg->uart_int_st; | |
| struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; | |
| struct uart_state *state = port->state; | |
| struct circ_buf *xmit = &port->state->xmit; | |
| spin_lock(&port->lock); | |
| intr_status = rd_regl(port, ureg->sirfsoc_int_st_reg); | |
| wr_regl(port, ureg->sirfsoc_int_st_reg, intr_status); | |
| intr_status &= rd_regl(port, ureg->sirfsoc_int_en_reg); | |
| if (unlikely(intr_status & (SIRFUART_ERR_INT_STAT(uint_st, | |
| sirfport->uart_reg->uart_type)))) { | |
| if (intr_status & uint_st->sirfsoc_rxd_brk) { | |
| port->icount.brk++; | |
| if (uart_handle_break(port)) | |
| goto recv_char; | |
| } | |
| if (intr_status & uint_st->sirfsoc_rx_oflow) { | |
| port->icount.overrun++; | |
| flag = TTY_OVERRUN; | |
| } | |
| if (intr_status & uint_st->sirfsoc_frm_err) { | |
| port->icount.frame++; | |
| flag = TTY_FRAME; | |
| } | |
| if (intr_status & uint_st->sirfsoc_parity_err) { | |
| port->icount.parity++; | |
| flag = TTY_PARITY; | |
| } | |
| wr_regl(port, ureg->sirfsoc_rx_fifo_op, SIRFUART_FIFO_RESET); | |
| wr_regl(port, ureg->sirfsoc_rx_fifo_op, 0); | |
| wr_regl(port, ureg->sirfsoc_rx_fifo_op, SIRFUART_FIFO_START); | |
| intr_status &= port->read_status_mask; | |
| uart_insert_char(port, intr_status, | |
| uint_en->sirfsoc_rx_oflow_en, 0, flag); | |
| } | |
| recv_char: | |
| if ((sirfport->uart_reg->uart_type == SIRF_REAL_UART) && | |
| (intr_status & SIRFUART_CTS_INT_ST(uint_st)) && | |
| !sirfport->tx_dma_state) { | |
| cts_status = rd_regl(port, ureg->sirfsoc_afc_ctrl) & | |
| SIRFUART_AFC_CTS_STATUS; | |
| if (cts_status != 0) | |
| cts_status = 0; | |
| else | |
| cts_status = 1; | |
| uart_handle_cts_change(port, cts_status); | |
| wake_up_interruptible(&state->port.delta_msr_wait); | |
| } | |
| if (!sirfport->rx_dma_chan && | |
| (intr_status & SIRFUART_RX_IO_INT_ST(uint_st))) { | |
| /* | |
| * chip will trigger continuous RX_TIMEOUT interrupt | |
| * in RXFIFO empty and not trigger if RXFIFO recevice | |
| * data in limit time, original method use RX_TIMEOUT | |
| * will trigger lots of useless interrupt in RXFIFO | |
| * empty.RXFIFO received one byte will trigger RX_DONE | |
| * interrupt.use RX_DONE to wait for data received | |
| * into RXFIFO, use RX_THD/RX_FULL for lots data receive | |
| * and use RX_TIMEOUT for the last left data. | |
| */ | |
| if (intr_status & uint_st->sirfsoc_rx_done) { | |
| if (!sirfport->is_atlas7) { | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg) | |
| & ~(uint_en->sirfsoc_rx_done_en)); | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg) | |
| | (uint_en->sirfsoc_rx_timeout_en)); | |
| } else { | |
| wr_regl(port, ureg->sirfsoc_int_en_clr_reg, | |
| uint_en->sirfsoc_rx_done_en); | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| uint_en->sirfsoc_rx_timeout_en); | |
| } | |
| } else { | |
| if (intr_status & uint_st->sirfsoc_rx_timeout) { | |
| if (!sirfport->is_atlas7) { | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg) | |
| & ~(uint_en->sirfsoc_rx_timeout_en)); | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg) | |
| | (uint_en->sirfsoc_rx_done_en)); | |
| } else { | |
| wr_regl(port, | |
| ureg->sirfsoc_int_en_clr_reg, | |
| uint_en->sirfsoc_rx_timeout_en); | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| uint_en->sirfsoc_rx_done_en); | |
| } | |
| } | |
| sirfsoc_uart_pio_rx_chars(port, port->fifosize); | |
| } | |
| } | |
| spin_unlock(&port->lock); | |
| tty_flip_buffer_push(&state->port); | |
| spin_lock(&port->lock); | |
| if (intr_status & uint_st->sirfsoc_txfifo_empty) { | |
| if (sirfport->tx_dma_chan) | |
| sirfsoc_uart_tx_with_dma(sirfport); | |
| else { | |
| if (uart_circ_empty(xmit) || uart_tx_stopped(port)) { | |
| spin_unlock(&port->lock); | |
| return IRQ_HANDLED; | |
| } else { | |
| sirfsoc_uart_pio_tx_chars(sirfport, | |
| port->fifosize); | |
| if ((uart_circ_empty(xmit)) && | |
| (rd_regl(port, ureg->sirfsoc_tx_fifo_status) & | |
| ufifo_st->ff_empty(port))) | |
| sirfsoc_uart_stop_tx(port); | |
| } | |
| } | |
| } | |
| spin_unlock(&port->lock); | |
| return IRQ_HANDLED; | |
| } | |
| static void sirfsoc_uart_rx_dma_complete_callback(void *param) | |
| { | |
| } | |
| /* submit rx dma task into dmaengine */ | |
| static void sirfsoc_uart_start_next_rx_dma(struct uart_port *port) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; | |
| wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, | |
| rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) & | |
| ~SIRFUART_IO_MODE); | |
| sirfport->rx_dma_items.xmit.tail = | |
| sirfport->rx_dma_items.xmit.head = 0; | |
| sirfport->rx_dma_items.desc = | |
| dmaengine_prep_dma_cyclic(sirfport->rx_dma_chan, | |
| sirfport->rx_dma_items.dma_addr, SIRFSOC_RX_DMA_BUF_SIZE, | |
| SIRFSOC_RX_DMA_BUF_SIZE / 2, | |
| DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT); | |
| if (IS_ERR_OR_NULL(sirfport->rx_dma_items.desc)) { | |
| dev_err(port->dev, "DMA slave single fail\n"); | |
| return; | |
| } | |
| sirfport->rx_dma_items.desc->callback = | |
| sirfsoc_uart_rx_dma_complete_callback; | |
| sirfport->rx_dma_items.desc->callback_param = sirfport; | |
| sirfport->rx_dma_items.cookie = | |
| dmaengine_submit(sirfport->rx_dma_items.desc); | |
| dma_async_issue_pending(sirfport->rx_dma_chan); | |
| if (!sirfport->is_atlas7) | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg) | | |
| SIRFUART_RX_DMA_INT_EN(uint_en, | |
| sirfport->uart_reg->uart_type)); | |
| else | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| SIRFUART_RX_DMA_INT_EN(uint_en, | |
| sirfport->uart_reg->uart_type)); | |
| } | |
| static unsigned int | |
| sirfsoc_usp_calc_sample_div(unsigned long set_rate, | |
| unsigned long ioclk_rate, unsigned long *sample_reg) | |
| { | |
| unsigned long min_delta = ~0UL; | |
| unsigned short sample_div; | |
| unsigned long ioclk_div = 0; | |
| unsigned long temp_delta; | |
| for (sample_div = SIRF_USP_MIN_SAMPLE_DIV; | |
| sample_div <= SIRF_MAX_SAMPLE_DIV; sample_div++) { | |
| temp_delta = ioclk_rate - | |
| (ioclk_rate + (set_rate * sample_div) / 2) | |
| / (set_rate * sample_div) * set_rate * sample_div; | |
| temp_delta = (temp_delta > 0) ? temp_delta : -temp_delta; | |
| if (temp_delta < min_delta) { | |
| ioclk_div = (2 * ioclk_rate / | |
| (set_rate * sample_div) + 1) / 2 - 1; | |
| if (ioclk_div > SIRF_IOCLK_DIV_MAX) | |
| continue; | |
| min_delta = temp_delta; | |
| *sample_reg = sample_div; | |
| if (!temp_delta) | |
| break; | |
| } | |
| } | |
| return ioclk_div; | |
| } | |
| static unsigned int | |
| sirfsoc_uart_calc_sample_div(unsigned long baud_rate, | |
| unsigned long ioclk_rate, unsigned long *set_baud) | |
| { | |
| unsigned long min_delta = ~0UL; | |
| unsigned short sample_div; | |
| unsigned int regv = 0; | |
| unsigned long ioclk_div; | |
| unsigned long baud_tmp; | |
| int temp_delta; | |
| for (sample_div = SIRF_MIN_SAMPLE_DIV; | |
| sample_div <= SIRF_MAX_SAMPLE_DIV; sample_div++) { | |
| ioclk_div = (ioclk_rate / (baud_rate * (sample_div + 1))) - 1; | |
| if (ioclk_div > SIRF_IOCLK_DIV_MAX) | |
| continue; | |
| baud_tmp = ioclk_rate / ((ioclk_div + 1) * (sample_div + 1)); | |
| temp_delta = baud_tmp - baud_rate; | |
| temp_delta = (temp_delta > 0) ? temp_delta : -temp_delta; | |
| if (temp_delta < min_delta) { | |
| regv = regv & (~SIRF_IOCLK_DIV_MASK); | |
| regv = regv | ioclk_div; | |
| regv = regv & (~SIRF_SAMPLE_DIV_MASK); | |
| regv = regv | (sample_div << SIRF_SAMPLE_DIV_SHIFT); | |
| min_delta = temp_delta; | |
| *set_baud = baud_tmp; | |
| } | |
| } | |
| return regv; | |
| } | |
| static void sirfsoc_uart_set_termios(struct uart_port *port, | |
| struct ktermios *termios, | |
| struct ktermios *old) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; | |
| unsigned long config_reg = 0; | |
| unsigned long baud_rate; | |
| unsigned long set_baud; | |
| unsigned long flags; | |
| unsigned long ic; | |
| unsigned int clk_div_reg = 0; | |
| unsigned long txfifo_op_reg, ioclk_rate; | |
| unsigned long rx_time_out; | |
| int threshold_div; | |
| u32 data_bit_len, stop_bit_len, len_val; | |
| unsigned long sample_div_reg = 0xf; | |
| ioclk_rate = port->uartclk; | |
| switch (termios->c_cflag & CSIZE) { | |
| default: | |
| case CS8: | |
| data_bit_len = 8; | |
| config_reg |= SIRFUART_DATA_BIT_LEN_8; | |
| break; | |
| case CS7: | |
| data_bit_len = 7; | |
| config_reg |= SIRFUART_DATA_BIT_LEN_7; | |
| break; | |
| case CS6: | |
| data_bit_len = 6; | |
| config_reg |= SIRFUART_DATA_BIT_LEN_6; | |
| break; | |
| case CS5: | |
| data_bit_len = 5; | |
| config_reg |= SIRFUART_DATA_BIT_LEN_5; | |
| break; | |
| } | |
| if (termios->c_cflag & CSTOPB) { | |
| config_reg |= SIRFUART_STOP_BIT_LEN_2; | |
| stop_bit_len = 2; | |
| } else | |
| stop_bit_len = 1; | |
| spin_lock_irqsave(&port->lock, flags); | |
| port->read_status_mask = uint_en->sirfsoc_rx_oflow_en; | |
| port->ignore_status_mask = 0; | |
| if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) { | |
| if (termios->c_iflag & INPCK) | |
| port->read_status_mask |= uint_en->sirfsoc_frm_err_en | | |
| uint_en->sirfsoc_parity_err_en; | |
| } else { | |
| if (termios->c_iflag & INPCK) | |
| port->read_status_mask |= uint_en->sirfsoc_frm_err_en; | |
| } | |
| if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) | |
| port->read_status_mask |= uint_en->sirfsoc_rxd_brk_en; | |
| if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) { | |
| if (termios->c_iflag & IGNPAR) | |
| port->ignore_status_mask |= | |
| uint_en->sirfsoc_frm_err_en | | |
| uint_en->sirfsoc_parity_err_en; | |
| if (termios->c_cflag & PARENB) { | |
| if (termios->c_cflag & CMSPAR) { | |
| if (termios->c_cflag & PARODD) | |
| config_reg |= SIRFUART_STICK_BIT_MARK; | |
| else | |
| config_reg |= SIRFUART_STICK_BIT_SPACE; | |
| } else { | |
| if (termios->c_cflag & PARODD) | |
| config_reg |= SIRFUART_STICK_BIT_ODD; | |
| else | |
| config_reg |= SIRFUART_STICK_BIT_EVEN; | |
| } | |
| } | |
| } else { | |
| if (termios->c_iflag & IGNPAR) | |
| port->ignore_status_mask |= | |
| uint_en->sirfsoc_frm_err_en; | |
| if (termios->c_cflag & PARENB) | |
| dev_warn(port->dev, | |
| "USP-UART not support parity err\n"); | |
| } | |
| if (termios->c_iflag & IGNBRK) { | |
| port->ignore_status_mask |= | |
| uint_en->sirfsoc_rxd_brk_en; | |
| if (termios->c_iflag & IGNPAR) | |
| port->ignore_status_mask |= | |
| uint_en->sirfsoc_rx_oflow_en; | |
| } | |
| if ((termios->c_cflag & CREAD) == 0) | |
| port->ignore_status_mask |= SIRFUART_DUMMY_READ; | |
| /* Hardware Flow Control Settings */ | |
| if (UART_ENABLE_MS(port, termios->c_cflag)) { | |
| if (!sirfport->ms_enabled) | |
| sirfsoc_uart_enable_ms(port); | |
| } else { | |
| if (sirfport->ms_enabled) | |
| sirfsoc_uart_disable_ms(port); | |
| } | |
| baud_rate = uart_get_baud_rate(port, termios, old, 0, 4000000); | |
| if (ioclk_rate == 150000000) { | |
| for (ic = 0; ic < SIRF_BAUD_RATE_SUPPORT_NR; ic++) | |
| if (baud_rate == baudrate_to_regv[ic].baud_rate) | |
| clk_div_reg = baudrate_to_regv[ic].reg_val; | |
| } | |
| set_baud = baud_rate; | |
| if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) { | |
| if (unlikely(clk_div_reg == 0)) | |
| clk_div_reg = sirfsoc_uart_calc_sample_div(baud_rate, | |
| ioclk_rate, &set_baud); | |
| wr_regl(port, ureg->sirfsoc_divisor, clk_div_reg); | |
| } else { | |
| clk_div_reg = sirfsoc_usp_calc_sample_div(baud_rate, | |
| ioclk_rate, &sample_div_reg); | |
| sample_div_reg--; | |
| set_baud = ((ioclk_rate / (clk_div_reg+1) - 1) / | |
| (sample_div_reg + 1)); | |
| /* setting usp mode 2 */ | |
| len_val = ((1 << SIRFSOC_USP_MODE2_RXD_DELAY_OFFSET) | | |
| (1 << SIRFSOC_USP_MODE2_TXD_DELAY_OFFSET)); | |
| len_val |= ((clk_div_reg & SIRFSOC_USP_MODE2_CLK_DIVISOR_MASK) | |
| << SIRFSOC_USP_MODE2_CLK_DIVISOR_OFFSET); | |
| wr_regl(port, ureg->sirfsoc_mode2, len_val); | |
| } | |
| if (tty_termios_baud_rate(termios)) | |
| tty_termios_encode_baud_rate(termios, set_baud, set_baud); | |
| /* set receive timeout && data bits len */ | |
| rx_time_out = SIRFSOC_UART_RX_TIMEOUT(set_baud, 20000); | |
| rx_time_out = SIRFUART_RECV_TIMEOUT_VALUE(rx_time_out); | |
| txfifo_op_reg = rd_regl(port, ureg->sirfsoc_tx_fifo_op); | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_op, | |
| (txfifo_op_reg & ~SIRFUART_FIFO_START)); | |
| if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) { | |
| config_reg |= SIRFUART_UART_RECV_TIMEOUT(rx_time_out); | |
| wr_regl(port, ureg->sirfsoc_line_ctrl, config_reg); | |
| } else { | |
| /*tx frame ctrl*/ | |
| len_val = (data_bit_len - 1) << SIRFSOC_USP_TX_DATA_LEN_OFFSET; | |
| len_val |= (data_bit_len + 1 + stop_bit_len - 1) << | |
| SIRFSOC_USP_TX_FRAME_LEN_OFFSET; | |
| len_val |= ((data_bit_len - 1) << | |
| SIRFSOC_USP_TX_SHIFTER_LEN_OFFSET); | |
| len_val |= (((clk_div_reg & 0xc00) >> 10) << | |
| SIRFSOC_USP_TX_CLK_DIVISOR_OFFSET); | |
| wr_regl(port, ureg->sirfsoc_tx_frame_ctrl, len_val); | |
| /*rx frame ctrl*/ | |
| len_val = (data_bit_len - 1) << SIRFSOC_USP_RX_DATA_LEN_OFFSET; | |
| len_val |= (data_bit_len + 1 + stop_bit_len - 1) << | |
| SIRFSOC_USP_RX_FRAME_LEN_OFFSET; | |
| len_val |= (data_bit_len - 1) << | |
| SIRFSOC_USP_RX_SHIFTER_LEN_OFFSET; | |
| len_val |= (((clk_div_reg & 0xf000) >> 12) << | |
| SIRFSOC_USP_RX_CLK_DIVISOR_OFFSET); | |
| wr_regl(port, ureg->sirfsoc_rx_frame_ctrl, len_val); | |
| /*async param*/ | |
| wr_regl(port, ureg->sirfsoc_async_param_reg, | |
| (SIRFUART_USP_RECV_TIMEOUT(rx_time_out)) | | |
| (sample_div_reg & SIRFSOC_USP_ASYNC_DIV2_MASK) << | |
| SIRFSOC_USP_ASYNC_DIV2_OFFSET); | |
| } | |
| if (sirfport->tx_dma_chan) | |
| wr_regl(port, ureg->sirfsoc_tx_dma_io_ctrl, SIRFUART_DMA_MODE); | |
| else | |
| wr_regl(port, ureg->sirfsoc_tx_dma_io_ctrl, SIRFUART_IO_MODE); | |
| if (sirfport->rx_dma_chan) | |
| wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, | |
| rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) & | |
| ~SIRFUART_IO_MODE); | |
| else | |
| wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, | |
| rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) | | |
| SIRFUART_IO_MODE); | |
| sirfport->rx_period_time = 20000000; | |
| /* Reset Rx/Tx FIFO Threshold level for proper baudrate */ | |
| if (set_baud < 1000000) | |
| threshold_div = 1; | |
| else | |
| threshold_div = 2; | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_ctrl, | |
| SIRFUART_FIFO_THD(port) / threshold_div); | |
| wr_regl(port, ureg->sirfsoc_rx_fifo_ctrl, | |
| SIRFUART_FIFO_THD(port) / threshold_div); | |
| txfifo_op_reg |= SIRFUART_FIFO_START; | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_op, txfifo_op_reg); | |
| uart_update_timeout(port, termios->c_cflag, set_baud); | |
| wr_regl(port, ureg->sirfsoc_tx_rx_en, SIRFUART_TX_EN | SIRFUART_RX_EN); | |
| spin_unlock_irqrestore(&port->lock, flags); | |
| } | |
| static void sirfsoc_uart_pm(struct uart_port *port, unsigned int state, | |
| unsigned int oldstate) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| if (!state) | |
| clk_prepare_enable(sirfport->clk); | |
| else | |
| clk_disable_unprepare(sirfport->clk); | |
| } | |
| static int sirfsoc_uart_startup(struct uart_port *port) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en; | |
| unsigned int index = port->line; | |
| int ret; | |
| irq_modify_status(port->irq, IRQ_NOREQUEST, IRQ_NOAUTOEN); | |
| ret = request_irq(port->irq, | |
| sirfsoc_uart_isr, | |
| 0, | |
| SIRFUART_PORT_NAME, | |
| sirfport); | |
| if (ret != 0) { | |
| dev_err(port->dev, "UART%d request IRQ line (%d) failed.\n", | |
| index, port->irq); | |
| goto irq_err; | |
| } | |
| /* initial hardware settings */ | |
| wr_regl(port, ureg->sirfsoc_tx_dma_io_ctrl, | |
| rd_regl(port, ureg->sirfsoc_tx_dma_io_ctrl) | | |
| SIRFUART_IO_MODE); | |
| wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, | |
| rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) | | |
| SIRFUART_IO_MODE); | |
| wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, | |
| rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) & | |
| ~SIRFUART_RX_DMA_FLUSH); | |
| wr_regl(port, ureg->sirfsoc_tx_dma_io_len, 0); | |
| wr_regl(port, ureg->sirfsoc_rx_dma_io_len, 0); | |
| wr_regl(port, ureg->sirfsoc_tx_rx_en, SIRFUART_RX_EN | SIRFUART_TX_EN); | |
| if (sirfport->uart_reg->uart_type == SIRF_USP_UART) | |
| wr_regl(port, ureg->sirfsoc_mode1, | |
| SIRFSOC_USP_ENDIAN_CTRL_LSBF | | |
| SIRFSOC_USP_EN); | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_op, SIRFUART_FIFO_RESET); | |
| wr_regl(port, ureg->sirfsoc_rx_fifo_op, SIRFUART_FIFO_RESET); | |
| wr_regl(port, ureg->sirfsoc_rx_fifo_op, 0); | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_ctrl, SIRFUART_FIFO_THD(port)); | |
| wr_regl(port, ureg->sirfsoc_rx_fifo_ctrl, SIRFUART_FIFO_THD(port)); | |
| if (sirfport->rx_dma_chan) | |
| wr_regl(port, ureg->sirfsoc_rx_fifo_level_chk, | |
| SIRFUART_RX_FIFO_CHK_SC(port->line, 0x1) | | |
| SIRFUART_RX_FIFO_CHK_LC(port->line, 0x2) | | |
| SIRFUART_RX_FIFO_CHK_HC(port->line, 0x4)); | |
| if (sirfport->tx_dma_chan) { | |
| sirfport->tx_dma_state = TX_DMA_IDLE; | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_level_chk, | |
| SIRFUART_TX_FIFO_CHK_SC(port->line, 0x1b) | | |
| SIRFUART_TX_FIFO_CHK_LC(port->line, 0xe) | | |
| SIRFUART_TX_FIFO_CHK_HC(port->line, 0x4)); | |
| } | |
| sirfport->ms_enabled = false; | |
| if (sirfport->uart_reg->uart_type == SIRF_USP_UART && | |
| sirfport->hw_flow_ctrl) { | |
| irq_modify_status(gpio_to_irq(sirfport->cts_gpio), | |
| IRQ_NOREQUEST, IRQ_NOAUTOEN); | |
| ret = request_irq(gpio_to_irq(sirfport->cts_gpio), | |
| sirfsoc_uart_usp_cts_handler, IRQF_TRIGGER_FALLING | | |
| IRQF_TRIGGER_RISING, "usp_cts_irq", sirfport); | |
| if (ret != 0) { | |
| dev_err(port->dev, "UART-USP:request gpio irq fail\n"); | |
| goto init_rx_err; | |
| } | |
| } | |
| if (sirfport->uart_reg->uart_type == SIRF_REAL_UART && | |
| sirfport->rx_dma_chan) | |
| wr_regl(port, ureg->sirfsoc_swh_dma_io, | |
| SIRFUART_CLEAR_RX_ADDR_EN); | |
| if (sirfport->uart_reg->uart_type == SIRF_USP_UART && | |
| sirfport->rx_dma_chan) | |
| wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, | |
| rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) | | |
| SIRFSOC_USP_FRADDR_CLR_EN); | |
| if (sirfport->rx_dma_chan && !sirfport->is_hrt_enabled) { | |
| sirfport->is_hrt_enabled = true; | |
| sirfport->rx_period_time = 20000000; | |
| sirfport->rx_last_pos = -1; | |
| sirfport->pio_fetch_cnt = 0; | |
| sirfport->rx_dma_items.xmit.tail = | |
| sirfport->rx_dma_items.xmit.head = 0; | |
| hrtimer_start(&sirfport->hrt, | |
| ns_to_ktime(sirfport->rx_period_time), | |
| HRTIMER_MODE_REL); | |
| } | |
| wr_regl(port, ureg->sirfsoc_rx_fifo_op, SIRFUART_FIFO_START); | |
| if (sirfport->rx_dma_chan) | |
| sirfsoc_uart_start_next_rx_dma(port); | |
| else { | |
| if (!sirfport->is_atlas7) | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| rd_regl(port, ureg->sirfsoc_int_en_reg) | | |
| SIRFUART_RX_IO_INT_EN(uint_en, | |
| sirfport->uart_reg->uart_type)); | |
| else | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, | |
| SIRFUART_RX_IO_INT_EN(uint_en, | |
| sirfport->uart_reg->uart_type)); | |
| } | |
| enable_irq(port->irq); | |
| return 0; | |
| init_rx_err: | |
| free_irq(port->irq, sirfport); | |
| irq_err: | |
| return ret; | |
| } | |
| static void sirfsoc_uart_shutdown(struct uart_port *port) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct circ_buf *xmit; | |
| xmit = &sirfport->rx_dma_items.xmit; | |
| if (!sirfport->is_atlas7) | |
| wr_regl(port, ureg->sirfsoc_int_en_reg, 0); | |
| else | |
| wr_regl(port, ureg->sirfsoc_int_en_clr_reg, ~0UL); | |
| free_irq(port->irq, sirfport); | |
| if (sirfport->ms_enabled) | |
| sirfsoc_uart_disable_ms(port); | |
| if (sirfport->uart_reg->uart_type == SIRF_USP_UART && | |
| sirfport->hw_flow_ctrl) { | |
| gpio_set_value(sirfport->rts_gpio, 1); | |
| free_irq(gpio_to_irq(sirfport->cts_gpio), sirfport); | |
| } | |
| if (sirfport->tx_dma_chan) | |
| sirfport->tx_dma_state = TX_DMA_IDLE; | |
| if (sirfport->rx_dma_chan && sirfport->is_hrt_enabled) { | |
| while (((rd_regl(port, ureg->sirfsoc_rx_fifo_status) & | |
| SIRFUART_RX_FIFO_MASK) > sirfport->pio_fetch_cnt) && | |
| !CIRC_CNT(xmit->head, xmit->tail, | |
| SIRFSOC_RX_DMA_BUF_SIZE)) | |
| ; | |
| sirfport->is_hrt_enabled = false; | |
| hrtimer_cancel(&sirfport->hrt); | |
| } | |
| } | |
| static const char *sirfsoc_uart_type(struct uart_port *port) | |
| { | |
| return port->type == SIRFSOC_PORT_TYPE ? SIRFUART_PORT_NAME : NULL; | |
| } | |
| static int sirfsoc_uart_request_port(struct uart_port *port) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_uart_param *uart_param = &sirfport->uart_reg->uart_param; | |
| void *ret; | |
| ret = request_mem_region(port->mapbase, | |
| SIRFUART_MAP_SIZE, uart_param->port_name); | |
| return ret ? 0 : -EBUSY; | |
| } | |
| static void sirfsoc_uart_release_port(struct uart_port *port) | |
| { | |
| release_mem_region(port->mapbase, SIRFUART_MAP_SIZE); | |
| } | |
| static void sirfsoc_uart_config_port(struct uart_port *port, int flags) | |
| { | |
| if (flags & UART_CONFIG_TYPE) { | |
| port->type = SIRFSOC_PORT_TYPE; | |
| sirfsoc_uart_request_port(port); | |
| } | |
| } | |
| static const struct uart_ops sirfsoc_uart_ops = { | |
| .tx_empty = sirfsoc_uart_tx_empty, | |
| .get_mctrl = sirfsoc_uart_get_mctrl, | |
| .set_mctrl = sirfsoc_uart_set_mctrl, | |
| .stop_tx = sirfsoc_uart_stop_tx, | |
| .start_tx = sirfsoc_uart_start_tx, | |
| .stop_rx = sirfsoc_uart_stop_rx, | |
| .enable_ms = sirfsoc_uart_enable_ms, | |
| .break_ctl = sirfsoc_uart_break_ctl, | |
| .startup = sirfsoc_uart_startup, | |
| .shutdown = sirfsoc_uart_shutdown, | |
| .set_termios = sirfsoc_uart_set_termios, | |
| .pm = sirfsoc_uart_pm, | |
| .type = sirfsoc_uart_type, | |
| .release_port = sirfsoc_uart_release_port, | |
| .request_port = sirfsoc_uart_request_port, | |
| .config_port = sirfsoc_uart_config_port, | |
| }; | |
| #ifdef CONFIG_SERIAL_SIRFSOC_CONSOLE | |
| static int __init | |
| sirfsoc_uart_console_setup(struct console *co, char *options) | |
| { | |
| unsigned int baud = 115200; | |
| unsigned int bits = 8; | |
| unsigned int parity = 'n'; | |
| unsigned int flow = 'n'; | |
| struct sirfsoc_uart_port *sirfport; | |
| struct sirfsoc_register *ureg; | |
| if (co->index < 0 || co->index >= SIRFSOC_UART_NR) | |
| co->index = 1; | |
| sirfport = sirf_ports[co->index]; | |
| if (!sirfport) | |
| return -ENODEV; | |
| ureg = &sirfport->uart_reg->uart_reg; | |
| if (!sirfport->port.mapbase) | |
| return -ENODEV; | |
| /* enable usp in mode1 register */ | |
| if (sirfport->uart_reg->uart_type == SIRF_USP_UART) | |
| wr_regl(&sirfport->port, ureg->sirfsoc_mode1, SIRFSOC_USP_EN | | |
| SIRFSOC_USP_ENDIAN_CTRL_LSBF); | |
| if (options) | |
| uart_parse_options(options, &baud, &parity, &bits, &flow); | |
| sirfport->port.cons = co; | |
| /* default console tx/rx transfer using io mode */ | |
| sirfport->rx_dma_chan = NULL; | |
| sirfport->tx_dma_chan = NULL; | |
| return uart_set_options(&sirfport->port, co, baud, parity, bits, flow); | |
| } | |
| static void sirfsoc_uart_console_putchar(struct uart_port *port, int ch) | |
| { | |
| struct sirfsoc_uart_port *sirfport = to_sirfport(port); | |
| struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg; | |
| struct sirfsoc_fifo_status *ufifo_st = &sirfport->uart_reg->fifo_status; | |
| while (rd_regl(port, ureg->sirfsoc_tx_fifo_status) & | |
| ufifo_st->ff_full(port)) | |
| cpu_relax(); | |
| wr_regl(port, ureg->sirfsoc_tx_fifo_data, ch); | |
| } | |
| static void sirfsoc_uart_console_write(struct console *co, const char *s, | |
| unsigned int count) | |
| { | |
| struct sirfsoc_uart_port *sirfport = sirf_ports[co->index]; | |
| uart_console_write(&sirfport->port, s, count, | |
| sirfsoc_uart_console_putchar); | |
| } | |
| static struct console sirfsoc_uart_console = { | |
| .name = SIRFSOC_UART_NAME, | |
| .device = uart_console_device, | |
| .flags = CON_PRINTBUFFER, | |
| .index = -1, | |
| .write = sirfsoc_uart_console_write, | |
| .setup = sirfsoc_uart_console_setup, | |
| .data = &sirfsoc_uart_drv, | |
| }; | |
| static int __init sirfsoc_uart_console_init(void) | |
| { | |
| register_console(&sirfsoc_uart_console); | |
| return 0; | |
| } | |
| console_initcall(sirfsoc_uart_console_init); | |
| #endif | |
| static struct uart_driver sirfsoc_uart_drv = { | |
| .owner = THIS_MODULE, | |
| .driver_name = SIRFUART_PORT_NAME, | |
| .nr = SIRFSOC_UART_NR, | |
| .dev_name = SIRFSOC_UART_NAME, | |
| .major = SIRFSOC_UART_MAJOR, | |
| .minor = SIRFSOC_UART_MINOR, | |
| #ifdef CONFIG_SERIAL_SIRFSOC_CONSOLE | |
| .cons = &sirfsoc_uart_console, | |
| #else | |
| .cons = NULL, | |
| #endif | |
| }; | |
| static enum hrtimer_restart | |
| sirfsoc_uart_rx_dma_hrtimer_callback(struct hrtimer *hrt) | |
| { | |
| struct sirfsoc_uart_port *sirfport; | |
| struct uart_port *port; | |
| int count, inserted; | |
| struct dma_tx_state tx_state; | |
| struct tty_struct *tty; | |
| struct sirfsoc_register *ureg; | |
| struct circ_buf *xmit; | |
| struct sirfsoc_fifo_status *ufifo_st; | |
| int max_pio_cnt; | |
| sirfport = container_of(hrt, struct sirfsoc_uart_port, hrt); | |
| port = &sirfport->port; | |
| inserted = 0; | |
| tty = port->state->port.tty; | |
| ureg = &sirfport->uart_reg->uart_reg; | |
| xmit = &sirfport->rx_dma_items.xmit; | |
| ufifo_st = &sirfport->uart_reg->fifo_status; | |
| dmaengine_tx_status(sirfport->rx_dma_chan, | |
| sirfport->rx_dma_items.cookie, &tx_state); | |
| if (SIRFSOC_RX_DMA_BUF_SIZE - tx_state.residue != | |
| sirfport->rx_last_pos) { | |
| xmit->head = SIRFSOC_RX_DMA_BUF_SIZE - tx_state.residue; | |
| sirfport->rx_last_pos = xmit->head; | |
| sirfport->pio_fetch_cnt = 0; | |
| } | |
| count = CIRC_CNT_TO_END(xmit->head, xmit->tail, | |
| SIRFSOC_RX_DMA_BUF_SIZE); | |
| while (count > 0) { | |
| inserted = tty_insert_flip_string(tty->port, | |
| (const unsigned char *)&xmit->buf[xmit->tail], count); | |
| if (!inserted) | |
| goto next_hrt; | |
| port->icount.rx += inserted; | |
| xmit->tail = (xmit->tail + inserted) & | |
| (SIRFSOC_RX_DMA_BUF_SIZE - 1); | |
| count = CIRC_CNT_TO_END(xmit->head, xmit->tail, | |
| SIRFSOC_RX_DMA_BUF_SIZE); | |
| tty_flip_buffer_push(tty->port); | |
| } | |
| /* | |
| * if RX DMA buffer data have all push into tty buffer, and there is | |
| * only little data(less than a dma transfer unit) left in rxfifo, | |
| * fetch it out in pio mode and switch back to dma immediately | |
| */ | |
| if (!inserted && !count && | |
| ((rd_regl(port, ureg->sirfsoc_rx_fifo_status) & | |
| SIRFUART_RX_FIFO_MASK) > sirfport->pio_fetch_cnt)) { | |
| dmaengine_pause(sirfport->rx_dma_chan); | |
| /* switch to pio mode */ | |
| wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, | |
| rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) | | |
| SIRFUART_IO_MODE); | |
| /* | |
| * UART controller SWH_DMA_IO register have CLEAR_RX_ADDR_EN | |
| * When found changing I/O to DMA mode, it clears | |
| * two low bits of read point; | |
| * USP have similar FRADDR_CLR_EN bit in USP_RX_DMA_IO_CTRL. | |
| * Fetch data out from rxfifo into DMA buffer in PIO mode, | |
| * while switch back to DMA mode, the data fetched will override | |
| * by DMA, as hardware have a strange behaviour: | |
| * after switch back to DMA mode, check rxfifo status it will | |
| * be the number PIO fetched, so record the fetched data count | |
| * to avoid the repeated fetch | |
| */ | |
| max_pio_cnt = 3; | |
| while (!(rd_regl(port, ureg->sirfsoc_rx_fifo_status) & | |
| ufifo_st->ff_empty(port)) && max_pio_cnt--) { | |
| xmit->buf[xmit->head] = | |
| rd_regl(port, ureg->sirfsoc_rx_fifo_data); | |
| xmit->head = (xmit->head + 1) & | |
| (SIRFSOC_RX_DMA_BUF_SIZE - 1); | |
| sirfport->pio_fetch_cnt++; | |
| } | |
| /* switch back to dma mode */ | |
| wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl, | |
| rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) & | |
| ~SIRFUART_IO_MODE); | |
| dmaengine_resume(sirfport->rx_dma_chan); | |
| } | |
| next_hrt: | |
| hrtimer_forward_now(hrt, ns_to_ktime(sirfport->rx_period_time)); | |
| return HRTIMER_RESTART; | |
| } | |
| static const struct of_device_id sirfsoc_uart_ids[] = { | |
| { .compatible = "sirf,prima2-uart", .data = &sirfsoc_uart,}, | |
| { .compatible = "sirf,atlas7-uart", .data = &sirfsoc_uart}, | |
| { .compatible = "sirf,prima2-usp-uart", .data = &sirfsoc_usp}, | |
| { .compatible = "sirf,atlas7-usp-uart", .data = &sirfsoc_usp}, | |
| {} | |
| }; | |
| MODULE_DEVICE_TABLE(of, sirfsoc_uart_ids); | |
| static int sirfsoc_uart_probe(struct platform_device *pdev) | |
| { | |
| struct device_node *np = pdev->dev.of_node; | |
| struct sirfsoc_uart_port *sirfport; | |
| struct uart_port *port; | |
| struct resource *res; | |
| int ret; | |
| struct dma_slave_config slv_cfg = { | |
| .src_maxburst = 1, | |
| }; | |
| struct dma_slave_config tx_slv_cfg = { | |
| .dst_maxburst = 2, | |
| }; | |
| const struct of_device_id *match; | |
| match = of_match_node(sirfsoc_uart_ids, np); | |
| sirfport = devm_kzalloc(&pdev->dev, sizeof(*sirfport), GFP_KERNEL); | |
| if (!sirfport) { | |
| ret = -ENOMEM; | |
| goto err; | |
| } | |
| sirfport->port.line = of_alias_get_id(np, "serial"); | |
| sirf_ports[sirfport->port.line] = sirfport; | |
| sirfport->port.iotype = UPIO_MEM; | |
| sirfport->port.flags = UPF_BOOT_AUTOCONF; | |
| port = &sirfport->port; | |
| port->dev = &pdev->dev; | |
| port->private_data = sirfport; | |
| sirfport->uart_reg = (struct sirfsoc_uart_register *)match->data; | |
| sirfport->hw_flow_ctrl = | |
| of_property_read_bool(np, "uart-has-rtscts") || | |
| of_property_read_bool(np, "sirf,uart-has-rtscts") /* deprecated */; | |
| if (of_device_is_compatible(np, "sirf,prima2-uart") || | |
| of_device_is_compatible(np, "sirf,atlas7-uart")) | |
| sirfport->uart_reg->uart_type = SIRF_REAL_UART; | |
| if (of_device_is_compatible(np, "sirf,prima2-usp-uart") || | |
| of_device_is_compatible(np, "sirf,atlas7-usp-uart")) { | |
| sirfport->uart_reg->uart_type = SIRF_USP_UART; | |
| if (!sirfport->hw_flow_ctrl) | |
| goto usp_no_flow_control; | |
| if (of_find_property(np, "cts-gpios", NULL)) | |
| sirfport->cts_gpio = | |
| of_get_named_gpio(np, "cts-gpios", 0); | |
| else | |
| sirfport->cts_gpio = -1; | |
| if (of_find_property(np, "rts-gpios", NULL)) | |
| sirfport->rts_gpio = | |
| of_get_named_gpio(np, "rts-gpios", 0); | |
| else | |
| sirfport->rts_gpio = -1; | |
| if ((!gpio_is_valid(sirfport->cts_gpio) || | |
| !gpio_is_valid(sirfport->rts_gpio))) { | |
| ret = -EINVAL; | |
| dev_err(&pdev->dev, | |
| "Usp flow control must have cts and rts gpio"); | |
| goto err; | |
| } | |
| ret = devm_gpio_request(&pdev->dev, sirfport->cts_gpio, | |
| "usp-cts-gpio"); | |
| if (ret) { | |
| dev_err(&pdev->dev, "Unable request cts gpio"); | |
| goto err; | |
| } | |
| gpio_direction_input(sirfport->cts_gpio); | |
| ret = devm_gpio_request(&pdev->dev, sirfport->rts_gpio, | |
| "usp-rts-gpio"); | |
| if (ret) { | |
| dev_err(&pdev->dev, "Unable request rts gpio"); | |
| goto err; | |
| } | |
| gpio_direction_output(sirfport->rts_gpio, 1); | |
| } | |
| usp_no_flow_control: | |
| if (of_device_is_compatible(np, "sirf,atlas7-uart") || | |
| of_device_is_compatible(np, "sirf,atlas7-usp-uart")) | |
| sirfport->is_atlas7 = true; | |
| if (of_property_read_u32(np, "fifosize", &port->fifosize)) { | |
| dev_err(&pdev->dev, | |
| "Unable to find fifosize in uart node.\n"); | |
| ret = -EFAULT; | |
| goto err; | |
| } | |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); | |
| if (res == NULL) { | |
| dev_err(&pdev->dev, "Insufficient resources.\n"); | |
| ret = -EFAULT; | |
| goto err; | |
| } | |
| port->mapbase = res->start; | |
| port->membase = devm_ioremap(&pdev->dev, | |
| res->start, resource_size(res)); | |
| if (!port->membase) { | |
| dev_err(&pdev->dev, "Cannot remap resource.\n"); | |
| ret = -ENOMEM; | |
| goto err; | |
| } | |
| res = platform_get_resource(pdev, IORESOURCE_IRQ, 0); | |
| if (res == NULL) { | |
| dev_err(&pdev->dev, "Insufficient resources.\n"); | |
| ret = -EFAULT; | |
| goto err; | |
| } | |
| port->irq = res->start; | |
| sirfport->clk = devm_clk_get(&pdev->dev, NULL); | |
| if (IS_ERR(sirfport->clk)) { | |
| ret = PTR_ERR(sirfport->clk); | |
| goto err; | |
| } | |
| port->uartclk = clk_get_rate(sirfport->clk); | |
| port->ops = &sirfsoc_uart_ops; | |
| spin_lock_init(&port->lock); | |
| platform_set_drvdata(pdev, sirfport); | |
| ret = uart_add_one_port(&sirfsoc_uart_drv, port); | |
| if (ret != 0) { | |
| dev_err(&pdev->dev, "Cannot add UART port(%d).\n", pdev->id); | |
| goto err; | |
| } | |
| sirfport->rx_dma_chan = dma_request_slave_channel(port->dev, "rx"); | |
| sirfport->rx_dma_items.xmit.buf = | |
| dma_alloc_coherent(port->dev, SIRFSOC_RX_DMA_BUF_SIZE, | |
| &sirfport->rx_dma_items.dma_addr, GFP_KERNEL); | |
| if (!sirfport->rx_dma_items.xmit.buf) { | |
| dev_err(port->dev, "Uart alloc bufa failed\n"); | |
| ret = -ENOMEM; | |
| goto alloc_coherent_err; | |
| } | |
| sirfport->rx_dma_items.xmit.head = | |
| sirfport->rx_dma_items.xmit.tail = 0; | |
| if (sirfport->rx_dma_chan) | |
| dmaengine_slave_config(sirfport->rx_dma_chan, &slv_cfg); | |
| sirfport->tx_dma_chan = dma_request_slave_channel(port->dev, "tx"); | |
| if (sirfport->tx_dma_chan) | |
| dmaengine_slave_config(sirfport->tx_dma_chan, &tx_slv_cfg); | |
| if (sirfport->rx_dma_chan) { | |
| hrtimer_init(&sirfport->hrt, CLOCK_MONOTONIC, HRTIMER_MODE_REL); | |
| sirfport->hrt.function = sirfsoc_uart_rx_dma_hrtimer_callback; | |
| sirfport->is_hrt_enabled = false; | |
| } | |
| return 0; | |
| alloc_coherent_err: | |
| dma_free_coherent(port->dev, SIRFSOC_RX_DMA_BUF_SIZE, | |
| sirfport->rx_dma_items.xmit.buf, | |
| sirfport->rx_dma_items.dma_addr); | |
| dma_release_channel(sirfport->rx_dma_chan); | |
| err: | |
| return ret; | |
| } | |
| static int sirfsoc_uart_remove(struct platform_device *pdev) | |
| { | |
| struct sirfsoc_uart_port *sirfport = platform_get_drvdata(pdev); | |
| struct uart_port *port = &sirfport->port; | |
| uart_remove_one_port(&sirfsoc_uart_drv, port); | |
| if (sirfport->rx_dma_chan) { | |
| dmaengine_terminate_all(sirfport->rx_dma_chan); | |
| dma_release_channel(sirfport->rx_dma_chan); | |
| dma_free_coherent(port->dev, SIRFSOC_RX_DMA_BUF_SIZE, | |
| sirfport->rx_dma_items.xmit.buf, | |
| sirfport->rx_dma_items.dma_addr); | |
| } | |
| if (sirfport->tx_dma_chan) { | |
| dmaengine_terminate_all(sirfport->tx_dma_chan); | |
| dma_release_channel(sirfport->tx_dma_chan); | |
| } | |
| return 0; | |
| } | |
| #ifdef CONFIG_PM_SLEEP | |
| static int | |
| sirfsoc_uart_suspend(struct device *pdev) | |
| { | |
| struct sirfsoc_uart_port *sirfport = dev_get_drvdata(pdev); | |
| struct uart_port *port = &sirfport->port; | |
| uart_suspend_port(&sirfsoc_uart_drv, port); | |
| return 0; | |
| } | |
| static int sirfsoc_uart_resume(struct device *pdev) | |
| { | |
| struct sirfsoc_uart_port *sirfport = dev_get_drvdata(pdev); | |
| struct uart_port *port = &sirfport->port; | |
| uart_resume_port(&sirfsoc_uart_drv, port); | |
| return 0; | |
| } | |
| #endif | |
| static const struct dev_pm_ops sirfsoc_uart_pm_ops = { | |
| SET_SYSTEM_SLEEP_PM_OPS(sirfsoc_uart_suspend, sirfsoc_uart_resume) | |
| }; | |
| static struct platform_driver sirfsoc_uart_driver = { | |
| .probe = sirfsoc_uart_probe, | |
| .remove = sirfsoc_uart_remove, | |
| .driver = { | |
| .name = SIRFUART_PORT_NAME, | |
| .of_match_table = sirfsoc_uart_ids, | |
| .pm = &sirfsoc_uart_pm_ops, | |
| }, | |
| }; | |
| static int __init sirfsoc_uart_init(void) | |
| { | |
| int ret = 0; | |
| ret = uart_register_driver(&sirfsoc_uart_drv); | |
| if (ret) | |
| goto out; | |
| ret = platform_driver_register(&sirfsoc_uart_driver); | |
| if (ret) | |
| uart_unregister_driver(&sirfsoc_uart_drv); | |
| out: | |
| return ret; | |
| } | |
| module_init(sirfsoc_uart_init); | |
| static void __exit sirfsoc_uart_exit(void) | |
| { | |
| platform_driver_unregister(&sirfsoc_uart_driver); | |
| uart_unregister_driver(&sirfsoc_uart_drv); | |
| } | |
| module_exit(sirfsoc_uart_exit); | |
| MODULE_LICENSE("GPL v2"); | |
| MODULE_AUTHOR("Bin Shi <Bin.Shi@csr.com>, Rong Wang<Rong.Wang@csr.com>"); | |
| MODULE_DESCRIPTION("CSR SiRFprimaII Uart Driver"); |