drivers/crypto/caam/regs.h

/* SPDX-License-Identifier: GPL-2.0 */
/*
 * CAAM hardware register-level view
 *
 * Copyright 2008-2011 Freescale Semiconductor, Inc.
 */

#ifndef REGS_H
#define REGS_H

#include <linux/types.h>
#include <linux/bitops.h>
#include <linux/io.h>

/*
 * Architecture-specific register access methods
 *
 * CAAM's bus-addressable registers are 64 bits internally.
 * They have been wired to be safely accessible on 32-bit
 * architectures, however. Registers were organized such
 * that (a) they can be contained in 32 bits, (b) if not, then they
 * can be treated as two 32-bit entities, or finally (c) if they
 * must be treated as a single 64-bit value, then this can safely
 * be done with two 32-bit cycles.
 *
 * For 32-bit operations on 64-bit values, CAAM follows the same
 * 64-bit register access conventions as it's predecessors, in that
 * writes are "triggered" by a write to the register at the numerically
 * higher address, thus, a full 64-bit write cycle requires a write
 * to the lower address, followed by a write to the higher address,
 * which will latch/execute the write cycle.
 *
 * For example, let's assume a SW reset of CAAM through the master
 * configuration register.
 * - SWRST is in bit 31 of MCFG.
 * - MCFG begins at base+0x0000.
 * - Bits 63-32 are a 32-bit word at base+0x0000 (numerically-lower)
 * - Bits 31-0 are a 32-bit word at base+0x0004 (numerically-higher)
 *
 * (and on Power, the convention is 0-31, 32-63, I know...)
 *
 * Assuming a 64-bit write to this MCFG to perform a software reset
 * would then require a write of 0 to base+0x0000, followed by a
 * write of 0x80000000 to base+0x0004, which would "execute" the
 * reset.
 *
 * Of course, since MCFG 63-32 is all zero, we could cheat and simply
 * write 0x8000000 to base+0x0004, and the reset would work fine.
 * However, since CAAM does contain some write-and-read-intended
 * 64-bit registers, this code defines 64-bit access methods for
 * the sake of internal consistency and simplicity, and so that a
 * clean transition to 64-bit is possible when it becomes necessary.
 *
 * There are limitations to this that the developer must recognize.
 * 32-bit architectures cannot enforce an atomic-64 operation,
 * Therefore:
 *
 * - On writes, since the HW is assumed to latch the cycle on the
 *   write of the higher-numeric-address word, then ordered
 *   writes work OK.
 *
 * - For reads, where a register contains a relevant value of more
 *   that 32 bits, the hardware employs logic to latch the other
 *   "half" of the data until read, ensuring an accurate value.
 *   This is of particular relevance when dealing with CAAM's
 *   performance counters.
 *
 */

extern bool caam_little_end;
extern bool caam_imx;

#define caam_to_cpu(len)				\
static inline u##len caam##len ## _to_cpu(u##len val)	\
{							\
	if (caam_little_end)				\
		return le##len ## _to_cpu(val);		\
	else						\
		return be##len ## _to_cpu(val);		\
}

#define cpu_to_caam(len)				\
static inline u##len cpu_to_caam##len(u##len val)	\
{							\
	if (caam_little_end)				\
		return cpu_to_le##len(val);		\
	else						\
		return cpu_to_be##len(val);		\
}

caam_to_cpu(16)
caam_to_cpu(32)
caam_to_cpu(64)
cpu_to_caam(16)
cpu_to_caam(32)
cpu_to_caam(64)

static inline void wr_reg32(void __iomem *reg, u32 data)
{
	if (caam_little_end)
		iowrite32(data, reg);
	else
		iowrite32be(data, reg);
}

static inline u32 rd_reg32(void __iomem *reg)
{
	if (caam_little_end)
		return ioread32(reg);

	return ioread32be(reg);
}

static inline void clrsetbits_32(void __iomem *reg, u32 clear, u32 set)
{
	if (caam_little_end)
		iowrite32((ioread32(reg) & ~clear) | set, reg);
	else
		iowrite32be((ioread32be(reg) & ~clear) | set, reg);
}

/*
 * The only users of these wr/rd_reg64 functions is the Job Ring (JR).
 * The DMA address registers in the JR are handled differently depending on
 * platform:
 *
 * 1. All BE CAAM platforms and i.MX platforms (LE CAAM):
 *
 *    base + 0x0000 : most-significant 32 bits
 *    base + 0x0004 : least-significant 32 bits
 *
 * The 32-bit version of this core therefore has to write to base + 0x0004
 * to set the 32-bit wide DMA address.
 *
 * 2. All other LE CAAM platforms (LS1021A etc.)
 *    base + 0x0000 : least-significant 32 bits
 *    base + 0x0004 : most-significant 32 bits
 */
#ifdef CONFIG_64BIT
static inline void wr_reg64(void __iomem *reg, u64 data)
{
	if (caam_little_end)
		iowrite64(data, reg);
	else
		iowrite64be(data, reg);
}

static inline u64 rd_reg64(void __iomem *reg)
{
	if (caam_little_end)
		return ioread64(reg);
	else
		return ioread64be(reg);
}

#else /* CONFIG_64BIT */
static inline void wr_reg64(void __iomem *reg, u64 data)
{
	if (!caam_imx && caam_little_end) {
		wr_reg32((u32 __iomem *)(reg) + 1, data >> 32);
		wr_reg32((u32 __iomem *)(reg), data);
	} else {
		wr_reg32((u32 __iomem *)(reg), data >> 32);
		wr_reg32((u32 __iomem *)(reg) + 1, data);
	}
}

static inline u64 rd_reg64(void __iomem *reg)
{
	if (!caam_imx && caam_little_end)
		return ((u64)rd_reg32((u32 __iomem *)(reg) + 1) << 32 |
			(u64)rd_reg32((u32 __iomem *)(reg)));

	return ((u64)rd_reg32((u32 __iomem *)(reg)) << 32 |
		(u64)rd_reg32((u32 __iomem *)(reg) + 1));
}
#endif /* CONFIG_64BIT  */

static inline u64 cpu_to_caam_dma64(dma_addr_t value)
{
	if (caam_imx)
		return (((u64)cpu_to_caam32(lower_32_bits(value)) << 32) |
			 (u64)cpu_to_caam32(upper_32_bits(value)));

	return cpu_to_caam64(value);
}

static inline u64 caam_dma64_to_cpu(u64 value)
{
	if (caam_imx)
		return (((u64)caam32_to_cpu(lower_32_bits(value)) << 32) |
			 (u64)caam32_to_cpu(upper_32_bits(value)));

	return caam64_to_cpu(value);
}

#ifdef CONFIG_ARCH_DMA_ADDR_T_64BIT
#define cpu_to_caam_dma(value) cpu_to_caam_dma64(value)
#define caam_dma_to_cpu(value) caam_dma64_to_cpu(value)
#else
#define cpu_to_caam_dma(value) cpu_to_caam32(value)
#define caam_dma_to_cpu(value) caam32_to_cpu(value)
#endif /* CONFIG_ARCH_DMA_ADDR_T_64BIT */

/*
 * jr_outentry
 * Represents each entry in a JobR output ring
 */
struct jr_outentry {
	dma_addr_t desc;/* Pointer to completed descriptor */
	u32 jrstatus;	/* Status for completed descriptor */
} __packed;

/*
 * caam_perfmon - Performance Monitor/Secure Memory Status/
 *                CAAM Global Status/Component Version IDs
 *
 * Spans f00-fff wherever instantiated
 */

/* Number of DECOs */
#define CHA_NUM_MS_DECONUM_SHIFT	24
#define CHA_NUM_MS_DECONUM_MASK	(0xfull << CHA_NUM_MS_DECONUM_SHIFT)

/*
 * CHA version IDs / instantiation bitfields
 * Defined for use with the cha_id fields in perfmon, but the same shift/mask
 * selectors can be used to pull out the number of instantiated blocks within
 * cha_num fields in perfmon because the locations are the same.
 */
#define CHA_ID_LS_AES_SHIFT	0
#define CHA_ID_LS_AES_MASK	(0xfull << CHA_ID_LS_AES_SHIFT)
#define CHA_ID_LS_AES_LP	(0x3ull << CHA_ID_LS_AES_SHIFT)
#define CHA_ID_LS_AES_HP	(0x4ull << CHA_ID_LS_AES_SHIFT)

#define CHA_ID_LS_DES_SHIFT	4
#define CHA_ID_LS_DES_MASK	(0xfull << CHA_ID_LS_DES_SHIFT)

#define CHA_ID_LS_ARC4_SHIFT	8
#define CHA_ID_LS_ARC4_MASK	(0xfull << CHA_ID_LS_ARC4_SHIFT)

#define CHA_ID_LS_MD_SHIFT	12
#define CHA_ID_LS_MD_MASK	(0xfull << CHA_ID_LS_MD_SHIFT)
#define CHA_ID_LS_MD_LP256	(0x0ull << CHA_ID_LS_MD_SHIFT)
#define CHA_ID_LS_MD_LP512	(0x1ull << CHA_ID_LS_MD_SHIFT)
#define CHA_ID_LS_MD_HP		(0x2ull << CHA_ID_LS_MD_SHIFT)

#define CHA_ID_LS_RNG_SHIFT	16
#define CHA_ID_LS_RNG_MASK	(0xfull << CHA_ID_LS_RNG_SHIFT)

#define CHA_ID_LS_SNW8_SHIFT	20
#define CHA_ID_LS_SNW8_MASK	(0xfull << CHA_ID_LS_SNW8_SHIFT)

#define CHA_ID_LS_KAS_SHIFT	24
#define CHA_ID_LS_KAS_MASK	(0xfull << CHA_ID_LS_KAS_SHIFT)

#define CHA_ID_LS_PK_SHIFT	28
#define CHA_ID_LS_PK_MASK	(0xfull << CHA_ID_LS_PK_SHIFT)

#define CHA_ID_MS_CRC_SHIFT	0
#define CHA_ID_MS_CRC_MASK	(0xfull << CHA_ID_MS_CRC_SHIFT)

#define CHA_ID_MS_SNW9_SHIFT	4
#define CHA_ID_MS_SNW9_MASK	(0xfull << CHA_ID_MS_SNW9_SHIFT)

#define CHA_ID_MS_DECO_SHIFT	24
#define CHA_ID_MS_DECO_MASK	(0xfull << CHA_ID_MS_DECO_SHIFT)

#define CHA_ID_MS_JR_SHIFT	28
#define CHA_ID_MS_JR_MASK	(0xfull << CHA_ID_MS_JR_SHIFT)

struct sec_vid {
	u16 ip_id;
	u8 maj_rev;
	u8 min_rev;
};

struct caam_perfmon {
	/* Performance Monitor Registers			f00-f9f */
	u64 req_dequeued;	/* PC_REQ_DEQ - Dequeued Requests	     */
	u64 ob_enc_req;	/* PC_OB_ENC_REQ - Outbound Encrypt Requests */
	u64 ib_dec_req;	/* PC_IB_DEC_REQ - Inbound Decrypt Requests  */
	u64 ob_enc_bytes;	/* PC_OB_ENCRYPT - Outbound Bytes Encrypted  */
	u64 ob_prot_bytes;	/* PC_OB_PROTECT - Outbound Bytes Protected  */
	u64 ib_dec_bytes;	/* PC_IB_DECRYPT - Inbound Bytes Decrypted   */
	u64 ib_valid_bytes;	/* PC_IB_VALIDATED Inbound Bytes Validated   */
	u64 rsvd[13];

	/* CAAM Hardware Instantiation Parameters		fa0-fbf */
	u32 cha_rev_ms;		/* CRNR - CHA Rev No. Most significant half*/
	u32 cha_rev_ls;		/* CRNR - CHA Rev No. Least significant half*/
#define CTPR_MS_QI_SHIFT	25
#define CTPR_MS_QI_MASK		(0x1ull << CTPR_MS_QI_SHIFT)
#define CTPR_MS_DPAA2		BIT(13)
#define CTPR_MS_VIRT_EN_INCL	0x00000001
#define CTPR_MS_VIRT_EN_POR	0x00000002
#define CTPR_MS_PG_SZ_MASK	0x10
#define CTPR_MS_PG_SZ_SHIFT	4
	u32 comp_parms_ms;	/* CTPR - Compile Parameters Register	*/
	u32 comp_parms_ls;	/* CTPR - Compile Parameters Register	*/
	u64 rsvd1[2];

	/* CAAM Global Status					fc0-fdf */
	u64 faultaddr;	/* FAR  - Fault Address		*/
	u32 faultliodn;	/* FALR - Fault Address LIODN	*/
	u32 faultdetail;	/* FADR - Fault Addr Detail	*/
	u32 rsvd2;
#define CSTA_PLEND		BIT(10)
#define CSTA_ALT_PLEND		BIT(18)
	u32 status;		/* CSTA - CAAM Status */
	u64 rsvd3;

	/* Component Instantiation Parameters			fe0-fff */
	u32 rtic_id;		/* RVID - RTIC Version ID	*/
	u32 ccb_id;		/* CCBVID - CCB Version ID	*/
	u32 cha_id_ms;		/* CHAVID - CHA Version ID Most Significant*/
	u32 cha_id_ls;		/* CHAVID - CHA Version ID Least Significant*/
	u32 cha_num_ms;		/* CHANUM - CHA Number Most Significant	*/
	u32 cha_num_ls;		/* CHANUM - CHA Number Least Significant*/
	u32 caam_id_ms;		/* CAAMVID - CAAM Version ID MS	*/
	u32 caam_id_ls;		/* CAAMVID - CAAM Version ID LS	*/
};

/* LIODN programming for DMA configuration */
#define MSTRID_LOCK_LIODN	0x80000000
#define MSTRID_LOCK_MAKETRUSTED	0x00010000	/* only for JR masterid */

#define MSTRID_LIODN_MASK	0x0fff
struct masterid {
	u32 liodn_ms;	/* lock and make-trusted control bits */
	u32 liodn_ls;	/* LIODN for non-sequence and seq access */
};

/* Partition ID for DMA configuration */
struct partid {
	u32 rsvd1;
	u32 pidr;	/* partition ID, DECO */
};

/* RNGB test mode (replicated twice in some configurations) */
/* Padded out to 0x100 */
struct rngtst {
	u32 mode;		/* RTSTMODEx - Test mode */
	u32 rsvd1[3];
	u32 reset;		/* RTSTRESETx - Test reset control */
	u32 rsvd2[3];
	u32 status;		/* RTSTSSTATUSx - Test status */
	u32 rsvd3;
	u32 errstat;		/* RTSTERRSTATx - Test error status */
	u32 rsvd4;
	u32 errctl;		/* RTSTERRCTLx - Test error control */
	u32 rsvd5;
	u32 entropy;		/* RTSTENTROPYx - Test entropy */
	u32 rsvd6[15];
	u32 verifctl;	/* RTSTVERIFCTLx - Test verification control */
	u32 rsvd7;
	u32 verifstat;	/* RTSTVERIFSTATx - Test verification status */
	u32 rsvd8;
	u32 verifdata;	/* RTSTVERIFDx - Test verification data */
	u32 rsvd9;
	u32 xkey;		/* RTSTXKEYx - Test XKEY */
	u32 rsvd10;
	u32 oscctctl;	/* RTSTOSCCTCTLx - Test osc. counter control */
	u32 rsvd11;
	u32 oscct;		/* RTSTOSCCTx - Test oscillator counter */
	u32 rsvd12;
	u32 oscctstat;	/* RTSTODCCTSTATx - Test osc counter status */
	u32 rsvd13[2];
	u32 ofifo[4];	/* RTSTOFIFOx - Test output FIFO */
	u32 rsvd14[15];
};

/* RNG4 TRNG test registers */
struct rng4tst {
#define RTMCTL_PRGM	0x00010000	/* 1 -> program mode, 0 -> run mode */
#define RTMCTL_SAMP_MODE_VON_NEUMANN_ES_SC	0 /* use von Neumann data in
						     both entropy shifter and
						     statistical checker */
#define RTMCTL_SAMP_MODE_RAW_ES_SC		1 /* use raw data in both
						     entropy shifter and
						     statistical checker */
#define RTMCTL_SAMP_MODE_VON_NEUMANN_ES_RAW_SC	2 /* use von Neumann data in
						     entropy shifter, raw data
						     in statistical checker */
#define RTMCTL_SAMP_MODE_INVALID		3 /* invalid combination */
	u32 rtmctl;		/* misc. control register */
	u32 rtscmisc;		/* statistical check misc. register */
	u32 rtpkrrng;		/* poker range register */
	union {
		u32 rtpkrmax;	/* PRGM=1: poker max. limit register */
		u32 rtpkrsq;	/* PRGM=0: poker square calc. result register */
	};
#define RTSDCTL_ENT_DLY_SHIFT 16
#define RTSDCTL_ENT_DLY_MASK (0xffff << RTSDCTL_ENT_DLY_SHIFT)
#define RTSDCTL_ENT_DLY_MIN 3200
#define RTSDCTL_ENT_DLY_MAX 12800
	u32 rtsdctl;		/* seed control register */
	union {
		u32 rtsblim;	/* PRGM=1: sparse bit limit register */
		u32 rttotsam;	/* PRGM=0: total samples register */
	};
	u32 rtfrqmin;		/* frequency count min. limit register */
#define RTFRQMAX_DISABLE	(1 << 20)
	union {
		u32 rtfrqmax;	/* PRGM=1: freq. count max. limit register */
		u32 rtfrqcnt;	/* PRGM=0: freq. count register */
	};
	u32 rsvd1[40];
#define RDSTA_SKVT 0x80000000
#define RDSTA_SKVN 0x40000000
#define RDSTA_IF0 0x00000001
#define RDSTA_IF1 0x00000002
#define RDSTA_IFMASK (RDSTA_IF1 | RDSTA_IF0)
	u32 rdsta;
	u32 rsvd2[15];
};

/*
 * caam_ctrl - basic core configuration
 * starts base + 0x0000 padded out to 0x1000
 */

#define KEK_KEY_SIZE		8
#define TKEK_KEY_SIZE		8
#define TDSK_KEY_SIZE		8

#define DECO_RESET	1	/* Use with DECO reset/availability regs */
#define DECO_RESET_0	(DECO_RESET << 0)
#define DECO_RESET_1	(DECO_RESET << 1)
#define DECO_RESET_2	(DECO_RESET << 2)
#define DECO_RESET_3	(DECO_RESET << 3)
#define DECO_RESET_4	(DECO_RESET << 4)

struct caam_ctrl {
	/* Basic Configuration Section				000-01f */
	/* Read/Writable					        */
	u32 rsvd1;
	u32 mcr;		/* MCFG      Master Config Register  */
	u32 rsvd2;
	u32 scfgr;		/* SCFGR, Security Config Register */

	/* Bus Access Configuration Section			010-11f */
	/* Read/Writable                                                */
	struct masterid jr_mid[4];	/* JRxLIODNR - JobR LIODN setup */
	u32 rsvd3[11];
	u32 jrstart;			/* JRSTART - Job Ring Start Register */
	struct masterid rtic_mid[4];	/* RTICxLIODNR - RTIC LIODN setup */
	u32 rsvd4[5];
	u32 deco_rsr;			/* DECORSR - Deco Request Source */
	u32 rsvd11;
	u32 deco_rq;			/* DECORR - DECO Request */
	struct partid deco_mid[5];	/* DECOxLIODNR - 1 per DECO */
	u32 rsvd5[22];

	/* DECO Availability/Reset Section			120-3ff */
	u32 deco_avail;		/* DAR - DECO availability */
	u32 deco_reset;		/* DRR - DECO reset */
	u32 rsvd6[182];

	/* Key Encryption/Decryption Configuration              400-5ff */
	/* Read/Writable only while in Non-secure mode                  */
	u32 kek[KEK_KEY_SIZE];	/* JDKEKR - Key Encryption Key */
	u32 tkek[TKEK_KEY_SIZE];	/* TDKEKR - Trusted Desc KEK */
	u32 tdsk[TDSK_KEY_SIZE];	/* TDSKR - Trusted Desc Signing Key */
	u32 rsvd7[32];
	u64 sknonce;			/* SKNR - Secure Key Nonce */
	u32 rsvd8[70];

	/* RNG Test/Verification/Debug Access                   600-7ff */
	/* (Useful in Test/Debug modes only...)                         */
	union {
		struct rngtst rtst[2];
		struct rng4tst r4tst[2];
	};

	u32 rsvd9[448];

	/* Performance Monitor                                  f00-fff */
	struct caam_perfmon perfmon;
};

/*
 * Controller master config register defs
 */
#define MCFGR_SWRESET		0x80000000 /* software reset */
#define MCFGR_WDENABLE		0x40000000 /* DECO watchdog enable */
#define MCFGR_WDFAIL		0x20000000 /* DECO watchdog force-fail */
#define MCFGR_DMA_RESET		0x10000000
#define MCFGR_LONG_PTR		0x00010000 /* Use >32-bit desc addressing */
#define SCFGR_RDBENABLE		0x00000400
#define SCFGR_VIRT_EN		0x00008000
#define DECORR_RQD0ENABLE	0x00000001 /* Enable DECO0 for direct access */
#define DECORSR_JR0		0x00000001 /* JR to supply TZ, SDID, ICID */
#define DECORSR_VALID		0x80000000
#define DECORR_DEN0		0x00010000 /* DECO0 available for access*/

/* AXI read cache control */
#define MCFGR_ARCACHE_SHIFT	12
#define MCFGR_ARCACHE_MASK	(0xf << MCFGR_ARCACHE_SHIFT)
#define MCFGR_ARCACHE_BUFF	(0x1 << MCFGR_ARCACHE_SHIFT)
#define MCFGR_ARCACHE_CACH	(0x2 << MCFGR_ARCACHE_SHIFT)
#define MCFGR_ARCACHE_RALL	(0x4 << MCFGR_ARCACHE_SHIFT)

/* AXI write cache control */
#define MCFGR_AWCACHE_SHIFT	8
#define MCFGR_AWCACHE_MASK	(0xf << MCFGR_AWCACHE_SHIFT)
#define MCFGR_AWCACHE_BUFF	(0x1 << MCFGR_AWCACHE_SHIFT)
#define MCFGR_AWCACHE_CACH	(0x2 << MCFGR_AWCACHE_SHIFT)
#define MCFGR_AWCACHE_WALL	(0x8 << MCFGR_AWCACHE_SHIFT)

/* AXI pipeline depth */
#define MCFGR_AXIPIPE_SHIFT	4
#define MCFGR_AXIPIPE_MASK	(0xf << MCFGR_AXIPIPE_SHIFT)

#define MCFGR_AXIPRI		0x00000008 /* Assert AXI priority sideband */
#define MCFGR_LARGE_BURST	0x00000004 /* 128/256-byte burst size */
#define MCFGR_BURST_64		0x00000001 /* 64-byte burst size */

/* JRSTART register offsets */
#define JRSTART_JR0_START       0x00000001 /* Start Job ring 0 */
#define JRSTART_JR1_START       0x00000002 /* Start Job ring 1 */
#define JRSTART_JR2_START       0x00000004 /* Start Job ring 2 */
#define JRSTART_JR3_START       0x00000008 /* Start Job ring 3 */

/*
 * caam_job_ring - direct job ring setup
 * 1-4 possible per instantiation, base + 1000/2000/3000/4000
 * Padded out to 0x1000
 */
struct caam_job_ring {
	/* Input ring */
	u64 inpring_base;	/* IRBAx -  Input desc ring baseaddr */
	u32 rsvd1;
	u32 inpring_size;	/* IRSx - Input ring size */
	u32 rsvd2;
	u32 inpring_avail;	/* IRSAx - Input ring room remaining */
	u32 rsvd3;
	u32 inpring_jobadd;	/* IRJAx - Input ring jobs added */

	/* Output Ring */
	u64 outring_base;	/* ORBAx - Output status ring base addr */
	u32 rsvd4;
	u32 outring_size;	/* ORSx - Output ring size */
	u32 rsvd5;
	u32 outring_rmvd;	/* ORJRx - Output ring jobs removed */
	u32 rsvd6;
	u32 outring_used;	/* ORSFx - Output ring slots full */

	/* Status/Configuration */
	u32 rsvd7;
	u32 jroutstatus;	/* JRSTAx - JobR output status */
	u32 rsvd8;
	u32 jrintstatus;	/* JRINTx - JobR interrupt status */
	u32 rconfig_hi;	/* JRxCFG - Ring configuration */
	u32 rconfig_lo;

	/* Indices. CAAM maintains as "heads" of each queue */
	u32 rsvd9;
	u32 inp_rdidx;	/* IRRIx - Input ring read index */
	u32 rsvd10;
	u32 out_wtidx;	/* ORWIx - Output ring write index */

	/* Command/control */
	u32 rsvd11;
	u32 jrcommand;	/* JRCRx - JobR command */

	u32 rsvd12[932];

	/* Performance Monitor                                  f00-fff */
	struct caam_perfmon perfmon;
};

#define JR_RINGSIZE_MASK	0x03ff
/*
 * jrstatus - Job Ring Output Status
 * All values in lo word
 * Also note, same values written out as status through QI
 * in the command/status field of a frame descriptor
 */
#define JRSTA_SSRC_SHIFT            28
#define JRSTA_SSRC_MASK             0xf0000000

#define JRSTA_SSRC_NONE             0x00000000
#define JRSTA_SSRC_CCB_ERROR        0x20000000
#define JRSTA_SSRC_JUMP_HALT_USER   0x30000000
#define JRSTA_SSRC_DECO             0x40000000
#define JRSTA_SSRC_JRERROR          0x60000000
#define JRSTA_SSRC_JUMP_HALT_CC     0x70000000

#define JRSTA_DECOERR_JUMP          0x08000000
#define JRSTA_DECOERR_INDEX_SHIFT   8
#define JRSTA_DECOERR_INDEX_MASK    0xff00
#define JRSTA_DECOERR_ERROR_MASK    0x00ff

#define JRSTA_DECOERR_NONE          0x00
#define JRSTA_DECOERR_LINKLEN       0x01
#define JRSTA_DECOERR_LINKPTR       0x02
#define JRSTA_DECOERR_JRCTRL        0x03
#define JRSTA_DECOERR_DESCCMD       0x04
#define JRSTA_DECOERR_ORDER         0x05
#define JRSTA_DECOERR_KEYCMD        0x06
#define JRSTA_DECOERR_LOADCMD       0x07
#define JRSTA_DECOERR_STORECMD      0x08
#define JRSTA_DECOERR_OPCMD         0x09
#define JRSTA_DECOERR_FIFOLDCMD     0x0a
#define JRSTA_DECOERR_FIFOSTCMD     0x0b
#define JRSTA_DECOERR_MOVECMD       0x0c
#define JRSTA_DECOERR_JUMPCMD       0x0d
#define JRSTA_DECOERR_MATHCMD       0x0e
#define JRSTA_DECOERR_SHASHCMD      0x0f
#define JRSTA_DECOERR_SEQCMD        0x10
#define JRSTA_DECOERR_DECOINTERNAL  0x11
#define JRSTA_DECOERR_SHDESCHDR     0x12
#define JRSTA_DECOERR_HDRLEN        0x13
#define JRSTA_DECOERR_BURSTER       0x14
#define JRSTA_DECOERR_DESCSIGNATURE 0x15
#define JRSTA_DECOERR_DMA           0x16
#define JRSTA_DECOERR_BURSTFIFO     0x17
#define JRSTA_DECOERR_JRRESET       0x1a
#define JRSTA_DECOERR_JOBFAIL       0x1b
#define JRSTA_DECOERR_DNRERR        0x80
#define JRSTA_DECOERR_UNDEFPCL      0x81
#define JRSTA_DECOERR_PDBERR        0x82
#define JRSTA_DECOERR_ANRPLY_LATE   0x83
#define JRSTA_DECOERR_ANRPLY_REPLAY 0x84
#define JRSTA_DECOERR_SEQOVF        0x85
#define JRSTA_DECOERR_INVSIGN       0x86
#define JRSTA_DECOERR_DSASIGN       0x87

#define JRSTA_CCBERR_JUMP           0x08000000
#define JRSTA_CCBERR_INDEX_MASK     0xff00
#define JRSTA_CCBERR_INDEX_SHIFT    8
#define JRSTA_CCBERR_CHAID_MASK     0x00f0
#define JRSTA_CCBERR_CHAID_SHIFT    4
#define JRSTA_CCBERR_ERRID_MASK     0x000f

#define JRSTA_CCBERR_CHAID_AES      (0x01 << JRSTA_CCBERR_CHAID_SHIFT)
#define JRSTA_CCBERR_CHAID_DES      (0x02 << JRSTA_CCBERR_CHAID_SHIFT)
#define JRSTA_CCBERR_CHAID_ARC4     (0x03 << JRSTA_CCBERR_CHAID_SHIFT)
#define JRSTA_CCBERR_CHAID_MD       (0x04 << JRSTA_CCBERR_CHAID_SHIFT)
#define JRSTA_CCBERR_CHAID_RNG      (0x05 << JRSTA_CCBERR_CHAID_SHIFT)
#define JRSTA_CCBERR_CHAID_SNOW     (0x06 << JRSTA_CCBERR_CHAID_SHIFT)
#define JRSTA_CCBERR_CHAID_KASUMI   (0x07 << JRSTA_CCBERR_CHAID_SHIFT)
#define JRSTA_CCBERR_CHAID_PK       (0x08 << JRSTA_CCBERR_CHAID_SHIFT)
#define JRSTA_CCBERR_CHAID_CRC      (0x09 << JRSTA_CCBERR_CHAID_SHIFT)

#define JRSTA_CCBERR_ERRID_NONE     0x00
#define JRSTA_CCBERR_ERRID_MODE     0x01
#define JRSTA_CCBERR_ERRID_DATASIZ  0x02
#define JRSTA_CCBERR_ERRID_KEYSIZ   0x03
#define JRSTA_CCBERR_ERRID_PKAMEMSZ 0x04
#define JRSTA_CCBERR_ERRID_PKBMEMSZ 0x05
#define JRSTA_CCBERR_ERRID_SEQUENCE 0x06
#define JRSTA_CCBERR_ERRID_PKDIVZRO 0x07
#define JRSTA_CCBERR_ERRID_PKMODEVN 0x08
#define JRSTA_CCBERR_ERRID_KEYPARIT 0x09
#define JRSTA_CCBERR_ERRID_ICVCHK   0x0a
#define JRSTA_CCBERR_ERRID_HARDWARE 0x0b
#define JRSTA_CCBERR_ERRID_CCMAAD   0x0c
#define JRSTA_CCBERR_ERRID_INVCHA   0x0f

#define JRINT_ERR_INDEX_MASK        0x3fff0000
#define JRINT_ERR_INDEX_SHIFT       16
#define JRINT_ERR_TYPE_MASK         0xf00
#define JRINT_ERR_TYPE_SHIFT        8
#define JRINT_ERR_HALT_MASK         0xc
#define JRINT_ERR_HALT_SHIFT        2
#define JRINT_ERR_HALT_INPROGRESS   0x4
#define JRINT_ERR_HALT_COMPLETE     0x8
#define JRINT_JR_ERROR              0x02
#define JRINT_JR_INT                0x01

#define JRINT_ERR_TYPE_WRITE        1
#define JRINT_ERR_TYPE_BAD_INPADDR  3
#define JRINT_ERR_TYPE_BAD_OUTADDR  4
#define JRINT_ERR_TYPE_INV_INPWRT   5
#define JRINT_ERR_TYPE_INV_OUTWRT   6
#define JRINT_ERR_TYPE_RESET        7
#define JRINT_ERR_TYPE_REMOVE_OFL   8
#define JRINT_ERR_TYPE_ADD_OFL      9

#define JRCFG_SOE		0x04
#define JRCFG_ICEN		0x02
#define JRCFG_IMSK		0x01
#define JRCFG_ICDCT_SHIFT	8
#define JRCFG_ICTT_SHIFT	16

#define JRCR_RESET                  0x01

/*
 * caam_assurance - Assurance Controller View
 * base + 0x6000 padded out to 0x1000
 */

struct rtic_element {
	u64 address;
	u32 rsvd;
	u32 length;
};

struct rtic_block {
	struct rtic_element element[2];
};

struct rtic_memhash {
	u32 memhash_be[32];
	u32 memhash_le[32];
};

struct caam_assurance {
    /* Status/Command/Watchdog */
	u32 rsvd1;
	u32 status;		/* RSTA - Status */
	u32 rsvd2;
	u32 cmd;		/* RCMD - Command */
	u32 rsvd3;
	u32 ctrl;		/* RCTL - Control */
	u32 rsvd4;
	u32 throttle;	/* RTHR - Throttle */
	u32 rsvd5[2];
	u64 watchdog;	/* RWDOG - Watchdog Timer */
	u32 rsvd6;
	u32 rend;		/* REND - Endian corrections */
	u32 rsvd7[50];

	/* Block access/configuration @ 100/110/120/130 */
	struct rtic_block memblk[4];	/* Memory Blocks A-D */
	u32 rsvd8[32];

	/* Block hashes @ 200/300/400/500 */
	struct rtic_memhash hash[4];	/* Block hash values A-D */
	u32 rsvd_3[640];
};

/*
 * caam_queue_if - QI configuration and control
 * starts base + 0x7000, padded out to 0x1000 long
 */

struct caam_queue_if {
	u32 qi_control_hi;	/* QICTL  - QI Control */
	u32 qi_control_lo;
	u32 rsvd1;
	u32 qi_status;	/* QISTA  - QI Status */
	u32 qi_deq_cfg_hi;	/* QIDQC  - QI Dequeue Configuration */
	u32 qi_deq_cfg_lo;
	u32 qi_enq_cfg_hi;	/* QISEQC - QI Enqueue Command     */
	u32 qi_enq_cfg_lo;
	u32 rsvd2[1016];
};

/* QI control bits - low word */
#define QICTL_DQEN      0x01              /* Enable frame pop          */
#define QICTL_STOP      0x02              /* Stop dequeue/enqueue      */
#define QICTL_SOE       0x04              /* Stop on error             */

/* QI control bits - high word */
#define QICTL_MBSI	0x01
#define QICTL_MHWSI	0x02
#define QICTL_MWSI	0x04
#define QICTL_MDWSI	0x08
#define QICTL_CBSI	0x10		/* CtrlDataByteSwapInput     */
#define QICTL_CHWSI	0x20		/* CtrlDataHalfSwapInput     */
#define QICTL_CWSI	0x40		/* CtrlDataWordSwapInput     */
#define QICTL_CDWSI	0x80		/* CtrlDataDWordSwapInput    */
#define QICTL_MBSO	0x0100
#define QICTL_MHWSO	0x0200
#define QICTL_MWSO	0x0400
#define QICTL_MDWSO	0x0800
#define QICTL_CBSO	0x1000		/* CtrlDataByteSwapOutput    */
#define QICTL_CHWSO	0x2000		/* CtrlDataHalfSwapOutput    */
#define QICTL_CWSO	0x4000		/* CtrlDataWordSwapOutput    */
#define QICTL_CDWSO     0x8000		/* CtrlDataDWordSwapOutput   */
#define QICTL_DMBS	0x010000
#define QICTL_EPO	0x020000

/* QI status bits */
#define QISTA_PHRDERR   0x01              /* PreHeader Read Error      */
#define QISTA_CFRDERR   0x02              /* Compound Frame Read Error */
#define QISTA_OFWRERR   0x04              /* Output Frame Read Error   */
#define QISTA_BPDERR    0x08              /* Buffer Pool Depleted      */
#define QISTA_BTSERR    0x10              /* Buffer Undersize          */
#define QISTA_CFWRERR   0x20              /* Compound Frame Write Err  */
#define QISTA_STOPD     0x80000000        /* QI Stopped (see QICTL)    */

/* deco_sg_table - DECO view of scatter/gather table */
struct deco_sg_table {
	u64 addr;		/* Segment Address */
	u32 elen;		/* E, F bits + 30-bit length */
	u32 bpid_offset;	/* Buffer Pool ID + 16-bit length */
};

/*
 * caam_deco - descriptor controller - CHA cluster block
 *
 * Only accessible when direct DECO access is turned on
 * (done in DECORR, via MID programmed in DECOxMID
 *
 * 5 typical, base + 0x8000/9000/a000/b000
 * Padded out to 0x1000 long
 */
struct caam_deco {
	u32 rsvd1;
	u32 cls1_mode;	/* CxC1MR -  Class 1 Mode */
	u32 rsvd2;
	u32 cls1_keysize;	/* CxC1KSR - Class 1 Key Size */
	u32 cls1_datasize_hi;	/* CxC1DSR - Class 1 Data Size */
	u32 cls1_datasize_lo;
	u32 rsvd3;
	u32 cls1_icvsize;	/* CxC1ICVSR - Class 1 ICV size */
	u32 rsvd4[5];
	u32 cha_ctrl;	/* CCTLR - CHA control */
	u32 rsvd5;
	u32 irq_crtl;	/* CxCIRQ - CCB interrupt done/error/clear */
	u32 rsvd6;
	u32 clr_written;	/* CxCWR - Clear-Written */
	u32 ccb_status_hi;	/* CxCSTA - CCB Status/Error */
	u32 ccb_status_lo;
	u32 rsvd7[3];
	u32 aad_size;	/* CxAADSZR - Current AAD Size */
	u32 rsvd8;
	u32 cls1_iv_size;	/* CxC1IVSZR - Current Class 1 IV Size */
	u32 rsvd9[7];
	u32 pkha_a_size;	/* PKASZRx - Size of PKHA A */
	u32 rsvd10;
	u32 pkha_b_size;	/* PKBSZRx - Size of PKHA B */
	u32 rsvd11;
	u32 pkha_n_size;	/* PKNSZRx - Size of PKHA N */
	u32 rsvd12;
	u32 pkha_e_size;	/* PKESZRx - Size of PKHA E */
	u32 rsvd13[24];
	u32 cls1_ctx[16];	/* CxC1CTXR - Class 1 Context @100 */
	u32 rsvd14[48];
	u32 cls1_key[8];	/* CxC1KEYR - Class 1 Key @200 */
	u32 rsvd15[121];
	u32 cls2_mode;	/* CxC2MR - Class 2 Mode */
	u32 rsvd16;
	u32 cls2_keysize;	/* CxX2KSR - Class 2 Key Size */
	u32 cls2_datasize_hi;	/* CxC2DSR - Class 2 Data Size */
	u32 cls2_datasize_lo;
	u32 rsvd17;
	u32 cls2_icvsize;	/* CxC2ICVSZR - Class 2 ICV Size */
	u32 rsvd18[56];
	u32 cls2_ctx[18];	/* CxC2CTXR - Class 2 Context @500 */
	u32 rsvd19[46];
	u32 cls2_key[32];	/* CxC2KEYR - Class2 Key @600 */
	u32 rsvd20[84];
	u32 inp_infofifo_hi;	/* CxIFIFO - Input Info FIFO @7d0 */
	u32 inp_infofifo_lo;
	u32 rsvd21[2];
	u64 inp_datafifo;	/* CxDFIFO - Input Data FIFO */
	u32 rsvd22[2];
	u64 out_datafifo;	/* CxOFIFO - Output Data FIFO */
	u32 rsvd23[2];
	u32 jr_ctl_hi;	/* CxJRR - JobR Control Register      @800 */
	u32 jr_ctl_lo;
	u64 jr_descaddr;	/* CxDADR - JobR Descriptor Address */
#define DECO_OP_STATUS_HI_ERR_MASK 0xF00000FF
	u32 op_status_hi;	/* DxOPSTA - DECO Operation Status */
	u32 op_status_lo;
	u32 rsvd24[2];
	u32 liodn;		/* DxLSR - DECO LIODN Status - non-seq */
	u32 td_liodn;	/* DxLSR - DECO LIODN Status - trustdesc */
	u32 rsvd26[6];
	u64 math[4];		/* DxMTH - Math register */
	u32 rsvd27[8];
	struct deco_sg_table gthr_tbl[4];	/* DxGTR - Gather Tables */
	u32 rsvd28[16];
	struct deco_sg_table sctr_tbl[4];	/* DxSTR - Scatter Tables */
	u32 rsvd29[48];
	u32 descbuf[64];	/* DxDESB - Descriptor buffer */
	u32 rscvd30[193];
#define DESC_DBG_DECO_STAT_HOST_ERR	0x00D00000
#define DESC_DBG_DECO_STAT_VALID	0x80000000
#define DESC_DBG_DECO_STAT_MASK		0x00F00000
	u32 desc_dbg;		/* DxDDR - DECO Debug Register */
	u32 rsvd31[126];
};

#define DECO_JQCR_WHL		0x20000000
#define DECO_JQCR_FOUR		0x10000000

#define JR_BLOCK_NUMBER		1
#define ASSURE_BLOCK_NUMBER	6
#define QI_BLOCK_NUMBER		7
#define DECO_BLOCK_NUMBER	8
#define PG_SIZE_4K		0x1000
#define PG_SIZE_64K		0x10000
#endif /* REGS_H */