| /* | |
| * Copyright (c) 2016 Marek Vasut <marex@denx.de> | |
| * | |
| * Driver for Hope RF HP03 digital temperature and pressure sensor. | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License version 2 as | |
| * published by the Free Software Foundation. | |
| */ | |
| #define pr_fmt(fmt) "hp03: " fmt | |
| #include <linux/module.h> | |
| #include <linux/delay.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/i2c.h> | |
| #include <linux/regmap.h> | |
| #include <linux/iio/iio.h> | |
| #include <linux/iio/sysfs.h> | |
| /* | |
| * The HP03 sensor occupies two fixed I2C addresses: | |
| * 0x50 ... read-only EEPROM with calibration data | |
| * 0x77 ... read-write ADC for pressure and temperature | |
| */ | |
| #define HP03_EEPROM_ADDR 0x50 | |
| #define HP03_ADC_ADDR 0x77 | |
| #define HP03_EEPROM_CX_OFFSET 0x10 | |
| #define HP03_EEPROM_AB_OFFSET 0x1e | |
| #define HP03_EEPROM_CD_OFFSET 0x20 | |
| #define HP03_ADC_WRITE_REG 0xff | |
| #define HP03_ADC_READ_REG 0xfd | |
| #define HP03_ADC_READ_PRESSURE 0xf0 /* D1 in datasheet */ | |
| #define HP03_ADC_READ_TEMP 0xe8 /* D2 in datasheet */ | |
| struct hp03_priv { | |
| struct i2c_client *client; | |
| struct mutex lock; | |
| struct gpio_desc *xclr_gpio; | |
| struct i2c_client *eeprom_client; | |
| struct regmap *eeprom_regmap; | |
| s32 pressure; /* kPa */ | |
| s32 temp; /* Deg. C */ | |
| }; | |
| static const struct iio_chan_spec hp03_channels[] = { | |
| { | |
| .type = IIO_PRESSURE, | |
| .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), | |
| .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), | |
| }, | |
| { | |
| .type = IIO_TEMP, | |
| .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), | |
| .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), | |
| }, | |
| }; | |
| static bool hp03_is_writeable_reg(struct device *dev, unsigned int reg) | |
| { | |
| return false; | |
| } | |
| static bool hp03_is_volatile_reg(struct device *dev, unsigned int reg) | |
| { | |
| return false; | |
| } | |
| static const struct regmap_config hp03_regmap_config = { | |
| .reg_bits = 8, | |
| .val_bits = 8, | |
| .max_register = HP03_EEPROM_CD_OFFSET + 1, | |
| .cache_type = REGCACHE_RBTREE, | |
| .writeable_reg = hp03_is_writeable_reg, | |
| .volatile_reg = hp03_is_volatile_reg, | |
| }; | |
| static int hp03_get_temp_pressure(struct hp03_priv *priv, const u8 reg) | |
| { | |
| int ret; | |
| ret = i2c_smbus_write_byte_data(priv->client, HP03_ADC_WRITE_REG, reg); | |
| if (ret < 0) | |
| return ret; | |
| msleep(50); /* Wait for conversion to finish */ | |
| return i2c_smbus_read_word_data(priv->client, HP03_ADC_READ_REG); | |
| } | |
| static int hp03_update_temp_pressure(struct hp03_priv *priv) | |
| { | |
| struct device *dev = &priv->client->dev; | |
| u8 coefs[18]; | |
| u16 cx_val[7]; | |
| int ab_val, d1_val, d2_val, diff_val, dut, off, sens, x; | |
| int i, ret; | |
| /* Sample coefficients from EEPROM */ | |
| ret = regmap_bulk_read(priv->eeprom_regmap, HP03_EEPROM_CX_OFFSET, | |
| coefs, sizeof(coefs)); | |
| if (ret < 0) { | |
| dev_err(dev, "Failed to read EEPROM (reg=%02x)\n", | |
| HP03_EEPROM_CX_OFFSET); | |
| return ret; | |
| } | |
| /* Sample Temperature and Pressure */ | |
| gpiod_set_value_cansleep(priv->xclr_gpio, 1); | |
| ret = hp03_get_temp_pressure(priv, HP03_ADC_READ_PRESSURE); | |
| if (ret < 0) { | |
| dev_err(dev, "Failed to read pressure\n"); | |
| goto err_adc; | |
| } | |
| d1_val = ret; | |
| ret = hp03_get_temp_pressure(priv, HP03_ADC_READ_TEMP); | |
| if (ret < 0) { | |
| dev_err(dev, "Failed to read temperature\n"); | |
| goto err_adc; | |
| } | |
| d2_val = ret; | |
| gpiod_set_value_cansleep(priv->xclr_gpio, 0); | |
| /* The Cx coefficients and Temp/Pressure values are MSB first. */ | |
| for (i = 0; i < 7; i++) | |
| cx_val[i] = (coefs[2 * i] << 8) | (coefs[(2 * i) + 1] << 0); | |
| d1_val = ((d1_val >> 8) & 0xff) | ((d1_val & 0xff) << 8); | |
| d2_val = ((d2_val >> 8) & 0xff) | ((d2_val & 0xff) << 8); | |
| /* Coefficient voodoo from the HP03 datasheet. */ | |
| if (d2_val >= cx_val[4]) | |
| ab_val = coefs[14]; /* A-value */ | |
| else | |
| ab_val = coefs[15]; /* B-value */ | |
| diff_val = d2_val - cx_val[4]; | |
| dut = (ab_val * (diff_val >> 7) * (diff_val >> 7)) >> coefs[16]; | |
| dut = diff_val - dut; | |
| off = (cx_val[1] + (((cx_val[3] - 1024) * dut) >> 14)) * 4; | |
| sens = cx_val[0] + ((cx_val[2] * dut) >> 10); | |
| x = ((sens * (d1_val - 7168)) >> 14) - off; | |
| priv->pressure = ((x * 100) >> 5) + (cx_val[6] * 10); | |
| priv->temp = 250 + ((dut * cx_val[5]) >> 16) - (dut >> coefs[17]); | |
| return 0; | |
| err_adc: | |
| gpiod_set_value_cansleep(priv->xclr_gpio, 0); | |
| return ret; | |
| } | |
| static int hp03_read_raw(struct iio_dev *indio_dev, | |
| struct iio_chan_spec const *chan, | |
| int *val, int *val2, long mask) | |
| { | |
| struct hp03_priv *priv = iio_priv(indio_dev); | |
| int ret; | |
| mutex_lock(&priv->lock); | |
| ret = hp03_update_temp_pressure(priv); | |
| mutex_unlock(&priv->lock); | |
| if (ret) | |
| return ret; | |
| switch (mask) { | |
| case IIO_CHAN_INFO_RAW: | |
| switch (chan->type) { | |
| case IIO_PRESSURE: | |
| *val = priv->pressure; | |
| return IIO_VAL_INT; | |
| case IIO_TEMP: | |
| *val = priv->temp; | |
| return IIO_VAL_INT; | |
| default: | |
| return -EINVAL; | |
| } | |
| break; | |
| case IIO_CHAN_INFO_SCALE: | |
| switch (chan->type) { | |
| case IIO_PRESSURE: | |
| *val = 0; | |
| *val2 = 1000; | |
| return IIO_VAL_INT_PLUS_MICRO; | |
| case IIO_TEMP: | |
| *val = 10; | |
| return IIO_VAL_INT; | |
| default: | |
| return -EINVAL; | |
| } | |
| break; | |
| default: | |
| return -EINVAL; | |
| } | |
| return -EINVAL; | |
| } | |
| static const struct iio_info hp03_info = { | |
| .driver_module = THIS_MODULE, | |
| .read_raw = &hp03_read_raw, | |
| }; | |
| static int hp03_probe(struct i2c_client *client, | |
| const struct i2c_device_id *id) | |
| { | |
| struct device *dev = &client->dev; | |
| struct iio_dev *indio_dev; | |
| struct hp03_priv *priv; | |
| int ret; | |
| indio_dev = devm_iio_device_alloc(dev, sizeof(*priv)); | |
| if (!indio_dev) | |
| return -ENOMEM; | |
| priv = iio_priv(indio_dev); | |
| priv->client = client; | |
| mutex_init(&priv->lock); | |
| indio_dev->dev.parent = dev; | |
| indio_dev->name = id->name; | |
| indio_dev->channels = hp03_channels; | |
| indio_dev->num_channels = ARRAY_SIZE(hp03_channels); | |
| indio_dev->info = &hp03_info; | |
| indio_dev->modes = INDIO_DIRECT_MODE; | |
| priv->xclr_gpio = devm_gpiod_get_index(dev, "xclr", 0, GPIOD_OUT_HIGH); | |
| if (IS_ERR(priv->xclr_gpio)) { | |
| dev_err(dev, "Failed to claim XCLR GPIO\n"); | |
| ret = PTR_ERR(priv->xclr_gpio); | |
| return ret; | |
| } | |
| /* | |
| * Allocate another device for the on-sensor EEPROM, | |
| * which has it's dedicated I2C address and contains | |
| * the calibration constants for the sensor. | |
| */ | |
| priv->eeprom_client = i2c_new_dummy(client->adapter, HP03_EEPROM_ADDR); | |
| if (!priv->eeprom_client) { | |
| dev_err(dev, "New EEPROM I2C device failed\n"); | |
| return -ENODEV; | |
| } | |
| priv->eeprom_regmap = regmap_init_i2c(priv->eeprom_client, | |
| &hp03_regmap_config); | |
| if (IS_ERR(priv->eeprom_regmap)) { | |
| dev_err(dev, "Failed to allocate EEPROM regmap\n"); | |
| ret = PTR_ERR(priv->eeprom_regmap); | |
| goto err_cleanup_eeprom_client; | |
| } | |
| ret = iio_device_register(indio_dev); | |
| if (ret) { | |
| dev_err(dev, "Failed to register IIO device\n"); | |
| goto err_cleanup_eeprom_regmap; | |
| } | |
| i2c_set_clientdata(client, indio_dev); | |
| return 0; | |
| err_cleanup_eeprom_regmap: | |
| regmap_exit(priv->eeprom_regmap); | |
| err_cleanup_eeprom_client: | |
| i2c_unregister_device(priv->eeprom_client); | |
| return ret; | |
| } | |
| static int hp03_remove(struct i2c_client *client) | |
| { | |
| struct iio_dev *indio_dev = i2c_get_clientdata(client); | |
| struct hp03_priv *priv = iio_priv(indio_dev); | |
| iio_device_unregister(indio_dev); | |
| regmap_exit(priv->eeprom_regmap); | |
| i2c_unregister_device(priv->eeprom_client); | |
| return 0; | |
| } | |
| static const struct i2c_device_id hp03_id[] = { | |
| { "hp03", 0 }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, hp03_id); | |
| static const struct of_device_id hp03_of_match[] = { | |
| { .compatible = "hoperf,hp03" }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(of, hp03_of_match); | |
| static struct i2c_driver hp03_driver = { | |
| .driver = { | |
| .name = "hp03", | |
| .of_match_table = hp03_of_match, | |
| }, | |
| .probe = hp03_probe, | |
| .remove = hp03_remove, | |
| .id_table = hp03_id, | |
| }; | |
| module_i2c_driver(hp03_driver); | |
| MODULE_AUTHOR("Marek Vasut <marex@denx.de>"); | |
| MODULE_DESCRIPTION("Driver for Hope RF HP03 pressure and temperature sensor"); | |
| MODULE_LICENSE("GPL v2"); |