| /* | |
| * drivers/media/i2c/as3645a.c - AS3645A and LM3555 flash controllers driver | |
| * | |
| * Copyright (C) 2008-2011 Nokia Corporation | |
| * Copyright (c) 2011, Intel Corporation. | |
| * | |
| * Contact: Laurent Pinchart <laurent.pinchart@ideasonboard.com> | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License | |
| * version 2 as published by the Free Software Foundation. | |
| * | |
| * This program is distributed in the hope that it will be useful, but | |
| * WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU | |
| * General Public License for more details. | |
| * | |
| * TODO: | |
| * - Check hardware FSTROBE control when sensor driver add support for this | |
| * | |
| */ | |
| #include <linux/delay.h> | |
| #include <linux/i2c.h> | |
| #include <linux/module.h> | |
| #include <linux/mutex.h> | |
| #include <linux/slab.h> | |
| #include <media/i2c/as3645a.h> | |
| #include <media/v4l2-ctrls.h> | |
| #include <media/v4l2-device.h> | |
| #define AS_TIMER_MS_TO_CODE(t) (((t) - 100) / 50) | |
| #define AS_TIMER_CODE_TO_MS(c) (50 * (c) + 100) | |
| /* Register definitions */ | |
| /* Read-only Design info register: Reset state: xxxx 0001 */ | |
| #define AS_DESIGN_INFO_REG 0x00 | |
| #define AS_DESIGN_INFO_FACTORY(x) (((x) >> 4)) | |
| #define AS_DESIGN_INFO_MODEL(x) ((x) & 0x0f) | |
| /* Read-only Version control register: Reset state: 0000 0000 | |
| * for first engineering samples | |
| */ | |
| #define AS_VERSION_CONTROL_REG 0x01 | |
| #define AS_VERSION_CONTROL_RFU(x) (((x) >> 4)) | |
| #define AS_VERSION_CONTROL_VERSION(x) ((x) & 0x0f) | |
| /* Read / Write (Indicator and timer register): Reset state: 0000 1111 */ | |
| #define AS_INDICATOR_AND_TIMER_REG 0x02 | |
| #define AS_INDICATOR_AND_TIMER_TIMEOUT_SHIFT 0 | |
| #define AS_INDICATOR_AND_TIMER_VREF_SHIFT 4 | |
| #define AS_INDICATOR_AND_TIMER_INDICATOR_SHIFT 6 | |
| /* Read / Write (Current set register): Reset state: 0110 1001 */ | |
| #define AS_CURRENT_SET_REG 0x03 | |
| #define AS_CURRENT_ASSIST_LIGHT_SHIFT 0 | |
| #define AS_CURRENT_LED_DET_ON (1 << 3) | |
| #define AS_CURRENT_FLASH_CURRENT_SHIFT 4 | |
| /* Read / Write (Control register): Reset state: 1011 0100 */ | |
| #define AS_CONTROL_REG 0x04 | |
| #define AS_CONTROL_MODE_SETTING_SHIFT 0 | |
| #define AS_CONTROL_STROBE_ON (1 << 2) | |
| #define AS_CONTROL_OUT_ON (1 << 3) | |
| #define AS_CONTROL_EXT_TORCH_ON (1 << 4) | |
| #define AS_CONTROL_STROBE_TYPE_EDGE (0 << 5) | |
| #define AS_CONTROL_STROBE_TYPE_LEVEL (1 << 5) | |
| #define AS_CONTROL_COIL_PEAK_SHIFT 6 | |
| /* Read only (D3 is read / write) (Fault and info): Reset state: 0000 x000 */ | |
| #define AS_FAULT_INFO_REG 0x05 | |
| #define AS_FAULT_INFO_INDUCTOR_PEAK_LIMIT (1 << 1) | |
| #define AS_FAULT_INFO_INDICATOR_LED (1 << 2) | |
| #define AS_FAULT_INFO_LED_AMOUNT (1 << 3) | |
| #define AS_FAULT_INFO_TIMEOUT (1 << 4) | |
| #define AS_FAULT_INFO_OVER_TEMPERATURE (1 << 5) | |
| #define AS_FAULT_INFO_SHORT_CIRCUIT (1 << 6) | |
| #define AS_FAULT_INFO_OVER_VOLTAGE (1 << 7) | |
| /* Boost register */ | |
| #define AS_BOOST_REG 0x0d | |
| #define AS_BOOST_CURRENT_DISABLE (0 << 0) | |
| #define AS_BOOST_CURRENT_ENABLE (1 << 0) | |
| /* Password register is used to unlock boost register writing */ | |
| #define AS_PASSWORD_REG 0x0f | |
| #define AS_PASSWORD_UNLOCK_VALUE 0x55 | |
| enum as_mode { | |
| AS_MODE_EXT_TORCH = 0 << AS_CONTROL_MODE_SETTING_SHIFT, | |
| AS_MODE_INDICATOR = 1 << AS_CONTROL_MODE_SETTING_SHIFT, | |
| AS_MODE_ASSIST = 2 << AS_CONTROL_MODE_SETTING_SHIFT, | |
| AS_MODE_FLASH = 3 << AS_CONTROL_MODE_SETTING_SHIFT, | |
| }; | |
| /* | |
| * struct as3645a | |
| * | |
| * @subdev: V4L2 subdev | |
| * @pdata: Flash platform data | |
| * @power_lock: Protects power_count | |
| * @power_count: Power reference count | |
| * @led_mode: V4L2 flash LED mode | |
| * @timeout: Flash timeout in microseconds | |
| * @flash_current: Flash current (0=200mA ... 15=500mA). Maximum | |
| * values are 400mA for two LEDs and 500mA for one LED. | |
| * @assist_current: Torch/Assist light current (0=20mA, 1=40mA ... 7=160mA) | |
| * @indicator_current: Indicator LED current (0=0mA, 1=2.5mA ... 4=10mA) | |
| * @strobe_source: Flash strobe source (software or external) | |
| */ | |
| struct as3645a { | |
| struct v4l2_subdev subdev; | |
| const struct as3645a_platform_data *pdata; | |
| struct mutex power_lock; | |
| int power_count; | |
| /* Controls */ | |
| struct v4l2_ctrl_handler ctrls; | |
| enum v4l2_flash_led_mode led_mode; | |
| unsigned int timeout; | |
| u8 flash_current; | |
| u8 assist_current; | |
| u8 indicator_current; | |
| enum v4l2_flash_strobe_source strobe_source; | |
| }; | |
| #define to_as3645a(sd) container_of(sd, struct as3645a, subdev) | |
| /* Return negative errno else zero on success */ | |
| static int as3645a_write(struct as3645a *flash, u8 addr, u8 val) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&flash->subdev); | |
| int rval; | |
| rval = i2c_smbus_write_byte_data(client, addr, val); | |
| dev_dbg(&client->dev, "Write Addr:%02X Val:%02X %s\n", addr, val, | |
| rval < 0 ? "fail" : "ok"); | |
| return rval; | |
| } | |
| /* Return negative errno else a data byte received from the device. */ | |
| static int as3645a_read(struct as3645a *flash, u8 addr) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&flash->subdev); | |
| int rval; | |
| rval = i2c_smbus_read_byte_data(client, addr); | |
| dev_dbg(&client->dev, "Read Addr:%02X Val:%02X %s\n", addr, rval, | |
| rval < 0 ? "fail" : "ok"); | |
| return rval; | |
| } | |
| /* ----------------------------------------------------------------------------- | |
| * Hardware configuration and trigger | |
| */ | |
| /* | |
| * as3645a_set_config - Set flash configuration registers | |
| * @flash: The flash | |
| * | |
| * Configure the hardware with flash, assist and indicator currents, as well as | |
| * flash timeout. | |
| * | |
| * Return 0 on success, or a negative error code if an I2C communication error | |
| * occurred. | |
| */ | |
| static int as3645a_set_config(struct as3645a *flash) | |
| { | |
| int ret; | |
| u8 val; | |
| val = (flash->flash_current << AS_CURRENT_FLASH_CURRENT_SHIFT) | |
| | (flash->assist_current << AS_CURRENT_ASSIST_LIGHT_SHIFT) | |
| | AS_CURRENT_LED_DET_ON; | |
| ret = as3645a_write(flash, AS_CURRENT_SET_REG, val); | |
| if (ret < 0) | |
| return ret; | |
| val = AS_TIMER_MS_TO_CODE(flash->timeout / 1000) | |
| << AS_INDICATOR_AND_TIMER_TIMEOUT_SHIFT; | |
| val |= (flash->pdata->vref << AS_INDICATOR_AND_TIMER_VREF_SHIFT) | |
| | ((flash->indicator_current ? flash->indicator_current - 1 : 0) | |
| << AS_INDICATOR_AND_TIMER_INDICATOR_SHIFT); | |
| return as3645a_write(flash, AS_INDICATOR_AND_TIMER_REG, val); | |
| } | |
| /* | |
| * as3645a_set_control - Set flash control register | |
| * @flash: The flash | |
| * @mode: Desired output mode | |
| * @on: Desired output state | |
| * | |
| * Configure the hardware with output mode and state. | |
| * | |
| * Return 0 on success, or a negative error code if an I2C communication error | |
| * occurred. | |
| */ | |
| static int | |
| as3645a_set_control(struct as3645a *flash, enum as_mode mode, bool on) | |
| { | |
| u8 reg; | |
| /* Configure output parameters and operation mode. */ | |
| reg = (flash->pdata->peak << AS_CONTROL_COIL_PEAK_SHIFT) | |
| | (on ? AS_CONTROL_OUT_ON : 0) | |
| | mode; | |
| if (flash->led_mode == V4L2_FLASH_LED_MODE_FLASH && | |
| flash->strobe_source == V4L2_FLASH_STROBE_SOURCE_EXTERNAL) { | |
| reg |= AS_CONTROL_STROBE_TYPE_LEVEL | |
| | AS_CONTROL_STROBE_ON; | |
| } | |
| return as3645a_write(flash, AS_CONTROL_REG, reg); | |
| } | |
| /* | |
| * as3645a_set_output - Configure output and operation mode | |
| * @flash: Flash controller | |
| * @strobe: Strobe the flash (only valid in flash mode) | |
| * | |
| * Turn the LEDs output on/off and set the operation mode based on the current | |
| * parameters. | |
| * | |
| * The AS3645A can't control the indicator LED independently of the flash/torch | |
| * LED. If the flash controller is in V4L2_FLASH_LED_MODE_NONE mode, set the | |
| * chip to indicator mode. Otherwise set it to assist light (torch) or flash | |
| * mode. | |
| * | |
| * In indicator and assist modes, turn the output on/off based on the indicator | |
| * and torch currents. In software strobe flash mode, turn the output on/off | |
| * based on the strobe parameter. | |
| */ | |
| static int as3645a_set_output(struct as3645a *flash, bool strobe) | |
| { | |
| enum as_mode mode; | |
| bool on; | |
| switch (flash->led_mode) { | |
| case V4L2_FLASH_LED_MODE_NONE: | |
| on = flash->indicator_current != 0; | |
| mode = AS_MODE_INDICATOR; | |
| break; | |
| case V4L2_FLASH_LED_MODE_TORCH: | |
| on = true; | |
| mode = AS_MODE_ASSIST; | |
| break; | |
| case V4L2_FLASH_LED_MODE_FLASH: | |
| on = strobe; | |
| mode = AS_MODE_FLASH; | |
| break; | |
| default: | |
| BUG(); | |
| } | |
| /* Configure output parameters and operation mode. */ | |
| return as3645a_set_control(flash, mode, on); | |
| } | |
| /* ----------------------------------------------------------------------------- | |
| * V4L2 controls | |
| */ | |
| static int as3645a_is_active(struct as3645a *flash) | |
| { | |
| int ret; | |
| ret = as3645a_read(flash, AS_CONTROL_REG); | |
| return ret < 0 ? ret : !!(ret & AS_CONTROL_OUT_ON); | |
| } | |
| static int as3645a_read_fault(struct as3645a *flash) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&flash->subdev); | |
| int rval; | |
| /* NOTE: reading register clear fault status */ | |
| rval = as3645a_read(flash, AS_FAULT_INFO_REG); | |
| if (rval < 0) | |
| return rval; | |
| if (rval & AS_FAULT_INFO_INDUCTOR_PEAK_LIMIT) | |
| dev_dbg(&client->dev, "Inductor Peak limit fault\n"); | |
| if (rval & AS_FAULT_INFO_INDICATOR_LED) | |
| dev_dbg(&client->dev, | |
| "Indicator LED fault: Short circuit or open loop\n"); | |
| dev_dbg(&client->dev, "%u connected LEDs\n", | |
| rval & AS_FAULT_INFO_LED_AMOUNT ? 2 : 1); | |
| if (rval & AS_FAULT_INFO_TIMEOUT) | |
| dev_dbg(&client->dev, "Timeout fault\n"); | |
| if (rval & AS_FAULT_INFO_OVER_TEMPERATURE) | |
| dev_dbg(&client->dev, "Over temperature fault\n"); | |
| if (rval & AS_FAULT_INFO_SHORT_CIRCUIT) | |
| dev_dbg(&client->dev, "Short circuit fault\n"); | |
| if (rval & AS_FAULT_INFO_OVER_VOLTAGE) | |
| dev_dbg(&client->dev, | |
| "Over voltage fault: Indicates missing capacitor or open connection\n"); | |
| return rval; | |
| } | |
| static int as3645a_get_ctrl(struct v4l2_ctrl *ctrl) | |
| { | |
| struct as3645a *flash = | |
| container_of(ctrl->handler, struct as3645a, ctrls); | |
| struct i2c_client *client = v4l2_get_subdevdata(&flash->subdev); | |
| int value; | |
| switch (ctrl->id) { | |
| case V4L2_CID_FLASH_FAULT: | |
| value = as3645a_read_fault(flash); | |
| if (value < 0) | |
| return value; | |
| ctrl->cur.val = 0; | |
| if (value & AS_FAULT_INFO_SHORT_CIRCUIT) | |
| ctrl->cur.val |= V4L2_FLASH_FAULT_SHORT_CIRCUIT; | |
| if (value & AS_FAULT_INFO_OVER_TEMPERATURE) | |
| ctrl->cur.val |= V4L2_FLASH_FAULT_OVER_TEMPERATURE; | |
| if (value & AS_FAULT_INFO_TIMEOUT) | |
| ctrl->cur.val |= V4L2_FLASH_FAULT_TIMEOUT; | |
| if (value & AS_FAULT_INFO_OVER_VOLTAGE) | |
| ctrl->cur.val |= V4L2_FLASH_FAULT_OVER_VOLTAGE; | |
| if (value & AS_FAULT_INFO_INDUCTOR_PEAK_LIMIT) | |
| ctrl->cur.val |= V4L2_FLASH_FAULT_OVER_CURRENT; | |
| if (value & AS_FAULT_INFO_INDICATOR_LED) | |
| ctrl->cur.val |= V4L2_FLASH_FAULT_INDICATOR; | |
| break; | |
| case V4L2_CID_FLASH_STROBE_STATUS: | |
| if (flash->led_mode != V4L2_FLASH_LED_MODE_FLASH) { | |
| ctrl->cur.val = 0; | |
| break; | |
| } | |
| value = as3645a_is_active(flash); | |
| if (value < 0) | |
| return value; | |
| ctrl->cur.val = value; | |
| break; | |
| } | |
| dev_dbg(&client->dev, "G_CTRL %08x:%d\n", ctrl->id, ctrl->cur.val); | |
| return 0; | |
| } | |
| static int as3645a_set_ctrl(struct v4l2_ctrl *ctrl) | |
| { | |
| struct as3645a *flash = | |
| container_of(ctrl->handler, struct as3645a, ctrls); | |
| struct i2c_client *client = v4l2_get_subdevdata(&flash->subdev); | |
| int ret; | |
| dev_dbg(&client->dev, "S_CTRL %08x:%d\n", ctrl->id, ctrl->val); | |
| /* If a control that doesn't apply to the current mode is modified, | |
| * we store the value and return immediately. The setting will be | |
| * applied when the LED mode is changed. Otherwise we apply the setting | |
| * immediately. | |
| */ | |
| switch (ctrl->id) { | |
| case V4L2_CID_FLASH_LED_MODE: | |
| if (flash->indicator_current) | |
| return -EBUSY; | |
| ret = as3645a_set_config(flash); | |
| if (ret < 0) | |
| return ret; | |
| flash->led_mode = ctrl->val; | |
| return as3645a_set_output(flash, false); | |
| case V4L2_CID_FLASH_STROBE_SOURCE: | |
| flash->strobe_source = ctrl->val; | |
| /* Applies to flash mode only. */ | |
| if (flash->led_mode != V4L2_FLASH_LED_MODE_FLASH) | |
| break; | |
| return as3645a_set_output(flash, false); | |
| case V4L2_CID_FLASH_STROBE: | |
| if (flash->led_mode != V4L2_FLASH_LED_MODE_FLASH) | |
| return -EBUSY; | |
| return as3645a_set_output(flash, true); | |
| case V4L2_CID_FLASH_STROBE_STOP: | |
| if (flash->led_mode != V4L2_FLASH_LED_MODE_FLASH) | |
| return -EBUSY; | |
| return as3645a_set_output(flash, false); | |
| case V4L2_CID_FLASH_TIMEOUT: | |
| flash->timeout = ctrl->val; | |
| /* Applies to flash mode only. */ | |
| if (flash->led_mode != V4L2_FLASH_LED_MODE_FLASH) | |
| break; | |
| return as3645a_set_config(flash); | |
| case V4L2_CID_FLASH_INTENSITY: | |
| flash->flash_current = (ctrl->val - AS3645A_FLASH_INTENSITY_MIN) | |
| / AS3645A_FLASH_INTENSITY_STEP; | |
| /* Applies to flash mode only. */ | |
| if (flash->led_mode != V4L2_FLASH_LED_MODE_FLASH) | |
| break; | |
| return as3645a_set_config(flash); | |
| case V4L2_CID_FLASH_TORCH_INTENSITY: | |
| flash->assist_current = | |
| (ctrl->val - AS3645A_TORCH_INTENSITY_MIN) | |
| / AS3645A_TORCH_INTENSITY_STEP; | |
| /* Applies to torch mode only. */ | |
| if (flash->led_mode != V4L2_FLASH_LED_MODE_TORCH) | |
| break; | |
| return as3645a_set_config(flash); | |
| case V4L2_CID_FLASH_INDICATOR_INTENSITY: | |
| if (flash->led_mode != V4L2_FLASH_LED_MODE_NONE) | |
| return -EBUSY; | |
| flash->indicator_current = | |
| (ctrl->val - AS3645A_INDICATOR_INTENSITY_MIN) | |
| / AS3645A_INDICATOR_INTENSITY_STEP; | |
| ret = as3645a_set_config(flash); | |
| if (ret < 0) | |
| return ret; | |
| if ((ctrl->val == 0) == (ctrl->cur.val == 0)) | |
| break; | |
| return as3645a_set_output(flash, false); | |
| } | |
| return 0; | |
| } | |
| static const struct v4l2_ctrl_ops as3645a_ctrl_ops = { | |
| .g_volatile_ctrl = as3645a_get_ctrl, | |
| .s_ctrl = as3645a_set_ctrl, | |
| }; | |
| /* ----------------------------------------------------------------------------- | |
| * V4L2 subdev core operations | |
| */ | |
| /* Put device into know state. */ | |
| static int as3645a_setup(struct as3645a *flash) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&flash->subdev); | |
| int ret; | |
| /* clear errors */ | |
| ret = as3645a_read(flash, AS_FAULT_INFO_REG); | |
| if (ret < 0) | |
| return ret; | |
| dev_dbg(&client->dev, "Fault info: %02x\n", ret); | |
| ret = as3645a_set_config(flash); | |
| if (ret < 0) | |
| return ret; | |
| ret = as3645a_set_output(flash, false); | |
| if (ret < 0) | |
| return ret; | |
| /* read status */ | |
| ret = as3645a_read_fault(flash); | |
| if (ret < 0) | |
| return ret; | |
| dev_dbg(&client->dev, "AS_INDICATOR_AND_TIMER_REG: %02x\n", | |
| as3645a_read(flash, AS_INDICATOR_AND_TIMER_REG)); | |
| dev_dbg(&client->dev, "AS_CURRENT_SET_REG: %02x\n", | |
| as3645a_read(flash, AS_CURRENT_SET_REG)); | |
| dev_dbg(&client->dev, "AS_CONTROL_REG: %02x\n", | |
| as3645a_read(flash, AS_CONTROL_REG)); | |
| return ret & ~AS_FAULT_INFO_LED_AMOUNT ? -EIO : 0; | |
| } | |
| static int __as3645a_set_power(struct as3645a *flash, int on) | |
| { | |
| int ret; | |
| if (!on) | |
| as3645a_set_control(flash, AS_MODE_EXT_TORCH, false); | |
| if (flash->pdata->set_power) { | |
| ret = flash->pdata->set_power(&flash->subdev, on); | |
| if (ret < 0) | |
| return ret; | |
| } | |
| if (!on) | |
| return 0; | |
| ret = as3645a_setup(flash); | |
| if (ret < 0) { | |
| if (flash->pdata->set_power) | |
| flash->pdata->set_power(&flash->subdev, 0); | |
| } | |
| return ret; | |
| } | |
| static int as3645a_set_power(struct v4l2_subdev *sd, int on) | |
| { | |
| struct as3645a *flash = to_as3645a(sd); | |
| int ret = 0; | |
| mutex_lock(&flash->power_lock); | |
| if (flash->power_count == !on) { | |
| ret = __as3645a_set_power(flash, !!on); | |
| if (ret < 0) | |
| goto done; | |
| } | |
| flash->power_count += on ? 1 : -1; | |
| WARN_ON(flash->power_count < 0); | |
| done: | |
| mutex_unlock(&flash->power_lock); | |
| return ret; | |
| } | |
| static int as3645a_registered(struct v4l2_subdev *sd) | |
| { | |
| struct as3645a *flash = to_as3645a(sd); | |
| struct i2c_client *client = v4l2_get_subdevdata(sd); | |
| int rval, man, model, rfu, version; | |
| const char *vendor; | |
| /* Power up the flash driver and read manufacturer ID, model ID, RFU | |
| * and version. | |
| */ | |
| rval = as3645a_set_power(&flash->subdev, 1); | |
| if (rval < 0) | |
| return rval; | |
| rval = as3645a_read(flash, AS_DESIGN_INFO_REG); | |
| if (rval < 0) | |
| goto power_off; | |
| man = AS_DESIGN_INFO_FACTORY(rval); | |
| model = AS_DESIGN_INFO_MODEL(rval); | |
| rval = as3645a_read(flash, AS_VERSION_CONTROL_REG); | |
| if (rval < 0) | |
| goto power_off; | |
| rfu = AS_VERSION_CONTROL_RFU(rval); | |
| version = AS_VERSION_CONTROL_VERSION(rval); | |
| /* Verify the chip model and version. */ | |
| if (model != 0x01 || rfu != 0x00) { | |
| dev_err(&client->dev, | |
| "AS3645A not detected (model %d rfu %d)\n", model, rfu); | |
| rval = -ENODEV; | |
| goto power_off; | |
| } | |
| switch (man) { | |
| case 1: | |
| vendor = "AMS, Austria Micro Systems"; | |
| break; | |
| case 2: | |
| vendor = "ADI, Analog Devices Inc."; | |
| break; | |
| case 3: | |
| vendor = "NSC, National Semiconductor"; | |
| break; | |
| case 4: | |
| vendor = "NXP"; | |
| break; | |
| case 5: | |
| vendor = "TI, Texas Instrument"; | |
| break; | |
| default: | |
| vendor = "Unknown"; | |
| } | |
| dev_info(&client->dev, "Chip vendor: %s (%d) Version: %d\n", vendor, | |
| man, version); | |
| rval = as3645a_write(flash, AS_PASSWORD_REG, AS_PASSWORD_UNLOCK_VALUE); | |
| if (rval < 0) | |
| goto power_off; | |
| rval = as3645a_write(flash, AS_BOOST_REG, AS_BOOST_CURRENT_DISABLE); | |
| if (rval < 0) | |
| goto power_off; | |
| /* Setup default values. This makes sure that the chip is in a known | |
| * state, in case the power rail can't be controlled. | |
| */ | |
| rval = as3645a_setup(flash); | |
| power_off: | |
| as3645a_set_power(&flash->subdev, 0); | |
| return rval; | |
| } | |
| static int as3645a_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) | |
| { | |
| return as3645a_set_power(sd, 1); | |
| } | |
| static int as3645a_close(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) | |
| { | |
| return as3645a_set_power(sd, 0); | |
| } | |
| static const struct v4l2_subdev_core_ops as3645a_core_ops = { | |
| .s_power = as3645a_set_power, | |
| }; | |
| static const struct v4l2_subdev_ops as3645a_ops = { | |
| .core = &as3645a_core_ops, | |
| }; | |
| static const struct v4l2_subdev_internal_ops as3645a_internal_ops = { | |
| .registered = as3645a_registered, | |
| .open = as3645a_open, | |
| .close = as3645a_close, | |
| }; | |
| /* ----------------------------------------------------------------------------- | |
| * I2C driver | |
| */ | |
| #ifdef CONFIG_PM | |
| static int as3645a_suspend(struct device *dev) | |
| { | |
| struct i2c_client *client = to_i2c_client(dev); | |
| struct v4l2_subdev *subdev = i2c_get_clientdata(client); | |
| struct as3645a *flash = to_as3645a(subdev); | |
| int rval; | |
| if (flash->power_count == 0) | |
| return 0; | |
| rval = __as3645a_set_power(flash, 0); | |
| dev_dbg(&client->dev, "Suspend %s\n", rval < 0 ? "failed" : "ok"); | |
| return rval; | |
| } | |
| static int as3645a_resume(struct device *dev) | |
| { | |
| struct i2c_client *client = to_i2c_client(dev); | |
| struct v4l2_subdev *subdev = i2c_get_clientdata(client); | |
| struct as3645a *flash = to_as3645a(subdev); | |
| int rval; | |
| if (flash->power_count == 0) | |
| return 0; | |
| rval = __as3645a_set_power(flash, 1); | |
| dev_dbg(&client->dev, "Resume %s\n", rval < 0 ? "fail" : "ok"); | |
| return rval; | |
| } | |
| #else | |
| #define as3645a_suspend NULL | |
| #define as3645a_resume NULL | |
| #endif /* CONFIG_PM */ | |
| /* | |
| * as3645a_init_controls - Create controls | |
| * @flash: The flash | |
| * | |
| * The number of LEDs reported in platform data is used to compute default | |
| * limits. Parameters passed through platform data can override those limits. | |
| */ | |
| static int as3645a_init_controls(struct as3645a *flash) | |
| { | |
| const struct as3645a_platform_data *pdata = flash->pdata; | |
| struct v4l2_ctrl *ctrl; | |
| int maximum; | |
| v4l2_ctrl_handler_init(&flash->ctrls, 10); | |
| /* V4L2_CID_FLASH_LED_MODE */ | |
| v4l2_ctrl_new_std_menu(&flash->ctrls, &as3645a_ctrl_ops, | |
| V4L2_CID_FLASH_LED_MODE, 2, ~7, | |
| V4L2_FLASH_LED_MODE_NONE); | |
| /* V4L2_CID_FLASH_STROBE_SOURCE */ | |
| v4l2_ctrl_new_std_menu(&flash->ctrls, &as3645a_ctrl_ops, | |
| V4L2_CID_FLASH_STROBE_SOURCE, | |
| pdata->ext_strobe ? 1 : 0, | |
| pdata->ext_strobe ? ~3 : ~1, | |
| V4L2_FLASH_STROBE_SOURCE_SOFTWARE); | |
| flash->strobe_source = V4L2_FLASH_STROBE_SOURCE_SOFTWARE; | |
| /* V4L2_CID_FLASH_STROBE */ | |
| v4l2_ctrl_new_std(&flash->ctrls, &as3645a_ctrl_ops, | |
| V4L2_CID_FLASH_STROBE, 0, 0, 0, 0); | |
| /* V4L2_CID_FLASH_STROBE_STOP */ | |
| v4l2_ctrl_new_std(&flash->ctrls, &as3645a_ctrl_ops, | |
| V4L2_CID_FLASH_STROBE_STOP, 0, 0, 0, 0); | |
| /* V4L2_CID_FLASH_STROBE_STATUS */ | |
| ctrl = v4l2_ctrl_new_std(&flash->ctrls, &as3645a_ctrl_ops, | |
| V4L2_CID_FLASH_STROBE_STATUS, 0, 1, 1, 1); | |
| if (ctrl != NULL) | |
| ctrl->flags |= V4L2_CTRL_FLAG_VOLATILE; | |
| /* V4L2_CID_FLASH_TIMEOUT */ | |
| maximum = pdata->timeout_max; | |
| v4l2_ctrl_new_std(&flash->ctrls, &as3645a_ctrl_ops, | |
| V4L2_CID_FLASH_TIMEOUT, AS3645A_FLASH_TIMEOUT_MIN, | |
| maximum, AS3645A_FLASH_TIMEOUT_STEP, maximum); | |
| flash->timeout = maximum; | |
| /* V4L2_CID_FLASH_INTENSITY */ | |
| maximum = pdata->flash_max_current; | |
| v4l2_ctrl_new_std(&flash->ctrls, &as3645a_ctrl_ops, | |
| V4L2_CID_FLASH_INTENSITY, AS3645A_FLASH_INTENSITY_MIN, | |
| maximum, AS3645A_FLASH_INTENSITY_STEP, maximum); | |
| flash->flash_current = (maximum - AS3645A_FLASH_INTENSITY_MIN) | |
| / AS3645A_FLASH_INTENSITY_STEP; | |
| /* V4L2_CID_FLASH_TORCH_INTENSITY */ | |
| maximum = pdata->torch_max_current; | |
| v4l2_ctrl_new_std(&flash->ctrls, &as3645a_ctrl_ops, | |
| V4L2_CID_FLASH_TORCH_INTENSITY, | |
| AS3645A_TORCH_INTENSITY_MIN, maximum, | |
| AS3645A_TORCH_INTENSITY_STEP, | |
| AS3645A_TORCH_INTENSITY_MIN); | |
| flash->assist_current = 0; | |
| /* V4L2_CID_FLASH_INDICATOR_INTENSITY */ | |
| v4l2_ctrl_new_std(&flash->ctrls, &as3645a_ctrl_ops, | |
| V4L2_CID_FLASH_INDICATOR_INTENSITY, | |
| AS3645A_INDICATOR_INTENSITY_MIN, | |
| AS3645A_INDICATOR_INTENSITY_MAX, | |
| AS3645A_INDICATOR_INTENSITY_STEP, | |
| AS3645A_INDICATOR_INTENSITY_MIN); | |
| flash->indicator_current = 0; | |
| /* V4L2_CID_FLASH_FAULT */ | |
| ctrl = v4l2_ctrl_new_std(&flash->ctrls, &as3645a_ctrl_ops, | |
| V4L2_CID_FLASH_FAULT, 0, | |
| V4L2_FLASH_FAULT_OVER_VOLTAGE | | |
| V4L2_FLASH_FAULT_TIMEOUT | | |
| V4L2_FLASH_FAULT_OVER_TEMPERATURE | | |
| V4L2_FLASH_FAULT_SHORT_CIRCUIT, 0, 0); | |
| if (ctrl != NULL) | |
| ctrl->flags |= V4L2_CTRL_FLAG_VOLATILE; | |
| flash->subdev.ctrl_handler = &flash->ctrls; | |
| return flash->ctrls.error; | |
| } | |
| static int as3645a_probe(struct i2c_client *client, | |
| const struct i2c_device_id *devid) | |
| { | |
| struct as3645a *flash; | |
| int ret; | |
| if (client->dev.platform_data == NULL) | |
| return -ENODEV; | |
| flash = devm_kzalloc(&client->dev, sizeof(*flash), GFP_KERNEL); | |
| if (flash == NULL) | |
| return -ENOMEM; | |
| flash->pdata = client->dev.platform_data; | |
| v4l2_i2c_subdev_init(&flash->subdev, client, &as3645a_ops); | |
| flash->subdev.internal_ops = &as3645a_internal_ops; | |
| flash->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; | |
| ret = as3645a_init_controls(flash); | |
| if (ret < 0) | |
| goto done; | |
| ret = media_entity_pads_init(&flash->subdev.entity, 0, NULL); | |
| if (ret < 0) | |
| goto done; | |
| flash->subdev.entity.function = MEDIA_ENT_F_FLASH; | |
| mutex_init(&flash->power_lock); | |
| flash->led_mode = V4L2_FLASH_LED_MODE_NONE; | |
| done: | |
| if (ret < 0) | |
| v4l2_ctrl_handler_free(&flash->ctrls); | |
| return ret; | |
| } | |
| static int as3645a_remove(struct i2c_client *client) | |
| { | |
| struct v4l2_subdev *subdev = i2c_get_clientdata(client); | |
| struct as3645a *flash = to_as3645a(subdev); | |
| v4l2_device_unregister_subdev(subdev); | |
| v4l2_ctrl_handler_free(&flash->ctrls); | |
| media_entity_cleanup(&flash->subdev.entity); | |
| mutex_destroy(&flash->power_lock); | |
| return 0; | |
| } | |
| static const struct i2c_device_id as3645a_id_table[] = { | |
| { AS3645A_NAME, 0 }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, as3645a_id_table); | |
| static const struct dev_pm_ops as3645a_pm_ops = { | |
| .suspend = as3645a_suspend, | |
| .resume = as3645a_resume, | |
| }; | |
| static struct i2c_driver as3645a_i2c_driver = { | |
| .driver = { | |
| .name = AS3645A_NAME, | |
| .pm = &as3645a_pm_ops, | |
| }, | |
| .probe = as3645a_probe, | |
| .remove = as3645a_remove, | |
| .id_table = as3645a_id_table, | |
| }; | |
| module_i2c_driver(as3645a_i2c_driver); | |
| MODULE_AUTHOR("Laurent Pinchart <laurent.pinchart@ideasonboard.com>"); | |
| MODULE_DESCRIPTION("LED flash driver for AS3645A, LM3555 and their clones"); | |
| MODULE_LICENSE("GPL"); |