| /* | |
| * Driver for Samsung S5K6AAFX SXGA 1/6" 1.3M CMOS Image Sensor | |
| * with embedded SoC ISP. | |
| * | |
| * Copyright (C) 2011, Samsung Electronics Co., Ltd. | |
| * Sylwester Nawrocki <s.nawrocki@samsung.com> | |
| * | |
| * Based on a driver authored by Dongsoo Nathaniel Kim. | |
| * Copyright (C) 2009, Dongsoo Nathaniel Kim <dongsoo45.kim@samsung.com> | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License as published by | |
| * the Free Software Foundation; either version 2 of the License, or | |
| * (at your option) any later version. | |
| */ | |
| #include <linux/clk.h> | |
| #include <linux/delay.h> | |
| #include <linux/gpio.h> | |
| #include <linux/i2c.h> | |
| #include <linux/media.h> | |
| #include <linux/module.h> | |
| #include <linux/regulator/consumer.h> | |
| #include <linux/slab.h> | |
| #include <media/media-entity.h> | |
| #include <media/v4l2-ctrls.h> | |
| #include <media/v4l2-device.h> | |
| #include <media/v4l2-subdev.h> | |
| #include <media/v4l2-mediabus.h> | |
| #include <media/i2c/s5k6aa.h> | |
| static int debug; | |
| module_param(debug, int, 0644); | |
| #define DRIVER_NAME "S5K6AA" | |
| /* The token to indicate array termination */ | |
| #define S5K6AA_TERM 0xffff | |
| #define S5K6AA_OUT_WIDTH_DEF 640 | |
| #define S5K6AA_OUT_HEIGHT_DEF 480 | |
| #define S5K6AA_WIN_WIDTH_MAX 1280 | |
| #define S5K6AA_WIN_HEIGHT_MAX 1024 | |
| #define S5K6AA_WIN_WIDTH_MIN 8 | |
| #define S5K6AA_WIN_HEIGHT_MIN 8 | |
| /* | |
| * H/W register Interface (0xD0000000 - 0xD0000FFF) | |
| */ | |
| #define AHB_MSB_ADDR_PTR 0xfcfc | |
| #define GEN_REG_OFFSH 0xd000 | |
| #define REG_CMDWR_ADDRH 0x0028 | |
| #define REG_CMDWR_ADDRL 0x002a | |
| #define REG_CMDRD_ADDRH 0x002c | |
| #define REG_CMDRD_ADDRL 0x002e | |
| #define REG_CMDBUF0_ADDR 0x0f12 | |
| #define REG_CMDBUF1_ADDR 0x0f10 | |
| /* | |
| * Host S/W Register interface (0x70000000 - 0x70002000) | |
| * The value of the two most significant address bytes is 0x7000, | |
| * (HOST_SWIF_OFFS_H). The register addresses below specify 2 LSBs. | |
| */ | |
| #define HOST_SWIF_OFFSH 0x7000 | |
| /* Initialization parameters */ | |
| /* Master clock frequency in KHz */ | |
| #define REG_I_INCLK_FREQ_L 0x01b8 | |
| #define REG_I_INCLK_FREQ_H 0x01ba | |
| #define MIN_MCLK_FREQ_KHZ 6000U | |
| #define MAX_MCLK_FREQ_KHZ 27000U | |
| #define REG_I_USE_NPVI_CLOCKS 0x01c6 | |
| #define REG_I_USE_NMIPI_CLOCKS 0x01c8 | |
| /* Clock configurations, n = 0..2. REG_I_* frequency unit is 4 kHz. */ | |
| #define REG_I_OPCLK_4KHZ(n) ((n) * 6 + 0x01cc) | |
| #define REG_I_MIN_OUTRATE_4KHZ(n) ((n) * 6 + 0x01ce) | |
| #define REG_I_MAX_OUTRATE_4KHZ(n) ((n) * 6 + 0x01d0) | |
| #define SYS_PLL_OUT_FREQ (48000000 / 4000) | |
| #define PCLK_FREQ_MIN (24000000 / 4000) | |
| #define PCLK_FREQ_MAX (48000000 / 4000) | |
| #define REG_I_INIT_PARAMS_UPDATED 0x01e0 | |
| #define REG_I_ERROR_INFO 0x01e2 | |
| /* General purpose parameters */ | |
| #define REG_USER_BRIGHTNESS 0x01e4 | |
| #define REG_USER_CONTRAST 0x01e6 | |
| #define REG_USER_SATURATION 0x01e8 | |
| #define REG_USER_SHARPBLUR 0x01ea | |
| #define REG_G_SPEC_EFFECTS 0x01ee | |
| #define REG_G_ENABLE_PREV 0x01f0 | |
| #define REG_G_ENABLE_PREV_CHG 0x01f2 | |
| #define REG_G_NEW_CFG_SYNC 0x01f8 | |
| #define REG_G_PREVZOOM_IN_WIDTH 0x020a | |
| #define REG_G_PREVZOOM_IN_HEIGHT 0x020c | |
| #define REG_G_PREVZOOM_IN_XOFFS 0x020e | |
| #define REG_G_PREVZOOM_IN_YOFFS 0x0210 | |
| #define REG_G_INPUTS_CHANGE_REQ 0x021a | |
| #define REG_G_ACTIVE_PREV_CFG 0x021c | |
| #define REG_G_PREV_CFG_CHG 0x021e | |
| #define REG_G_PREV_OPEN_AFTER_CH 0x0220 | |
| #define REG_G_PREV_CFG_ERROR 0x0222 | |
| /* Preview control section. n = 0...4. */ | |
| #define PREG(n, x) ((n) * 0x26 + x) | |
| #define REG_P_OUT_WIDTH(n) PREG(n, 0x0242) | |
| #define REG_P_OUT_HEIGHT(n) PREG(n, 0x0244) | |
| #define REG_P_FMT(n) PREG(n, 0x0246) | |
| #define REG_P_MAX_OUT_RATE(n) PREG(n, 0x0248) | |
| #define REG_P_MIN_OUT_RATE(n) PREG(n, 0x024a) | |
| #define REG_P_PVI_MASK(n) PREG(n, 0x024c) | |
| #define REG_P_CLK_INDEX(n) PREG(n, 0x024e) | |
| #define REG_P_FR_RATE_TYPE(n) PREG(n, 0x0250) | |
| #define FR_RATE_DYNAMIC 0 | |
| #define FR_RATE_FIXED 1 | |
| #define FR_RATE_FIXED_ACCURATE 2 | |
| #define REG_P_FR_RATE_Q_TYPE(n) PREG(n, 0x0252) | |
| #define FR_RATE_Q_BEST_FRRATE 1 /* Binning enabled */ | |
| #define FR_RATE_Q_BEST_QUALITY 2 /* Binning disabled */ | |
| /* Frame period in 0.1 ms units */ | |
| #define REG_P_MAX_FR_TIME(n) PREG(n, 0x0254) | |
| #define REG_P_MIN_FR_TIME(n) PREG(n, 0x0256) | |
| /* Conversion to REG_P_[MAX/MIN]_FR_TIME value; __t: time in us */ | |
| #define US_TO_FR_TIME(__t) ((__t) / 100) | |
| #define S5K6AA_MIN_FR_TIME 33300 /* us */ | |
| #define S5K6AA_MAX_FR_TIME 650000 /* us */ | |
| #define S5K6AA_MAX_HIGHRES_FR_TIME 666 /* x100 us */ | |
| /* The below 5 registers are for "device correction" values */ | |
| #define REG_P_COLORTEMP(n) PREG(n, 0x025e) | |
| #define REG_P_PREV_MIRROR(n) PREG(n, 0x0262) | |
| /* Extended image property controls */ | |
| /* Exposure time in 10 us units */ | |
| #define REG_SF_USR_EXPOSURE_L 0x03c6 | |
| #define REG_SF_USR_EXPOSURE_H 0x03c8 | |
| #define REG_SF_USR_EXPOSURE_CHG 0x03ca | |
| #define REG_SF_USR_TOT_GAIN 0x03cc | |
| #define REG_SF_USR_TOT_GAIN_CHG 0x03ce | |
| #define REG_SF_RGAIN 0x03d0 | |
| #define REG_SF_RGAIN_CHG 0x03d2 | |
| #define REG_SF_GGAIN 0x03d4 | |
| #define REG_SF_GGAIN_CHG 0x03d6 | |
| #define REG_SF_BGAIN 0x03d8 | |
| #define REG_SF_BGAIN_CHG 0x03da | |
| #define REG_SF_FLICKER_QUANT 0x03dc | |
| #define REG_SF_FLICKER_QUANT_CHG 0x03de | |
| /* Output interface (parallel/MIPI) setup */ | |
| #define REG_OIF_EN_MIPI_LANES 0x03fa | |
| #define REG_OIF_EN_PACKETS 0x03fc | |
| #define REG_OIF_CFG_CHG 0x03fe | |
| /* Auto-algorithms enable mask */ | |
| #define REG_DBG_AUTOALG_EN 0x0400 | |
| #define AALG_ALL_EN_MASK (1 << 0) | |
| #define AALG_AE_EN_MASK (1 << 1) | |
| #define AALG_DIVLEI_EN_MASK (1 << 2) | |
| #define AALG_WB_EN_MASK (1 << 3) | |
| #define AALG_FLICKER_EN_MASK (1 << 5) | |
| #define AALG_FIT_EN_MASK (1 << 6) | |
| #define AALG_WRHW_EN_MASK (1 << 7) | |
| /* Firmware revision information */ | |
| #define REG_FW_APIVER 0x012e | |
| #define S5K6AAFX_FW_APIVER 0x0001 | |
| #define REG_FW_REVISION 0x0130 | |
| /* For now we use only one user configuration register set */ | |
| #define S5K6AA_MAX_PRESETS 1 | |
| static const char * const s5k6aa_supply_names[] = { | |
| "vdd_core", /* Digital core supply 1.5V (1.4V to 1.6V) */ | |
| "vdda", /* Analog power supply 2.8V (2.6V to 3.0V) */ | |
| "vdd_reg", /* Regulator input power 1.8V (1.7V to 1.9V) | |
| or 2.8V (2.6V to 3.0) */ | |
| "vddio", /* I/O supply 1.8V (1.65V to 1.95V) | |
| or 2.8V (2.5V to 3.1V) */ | |
| }; | |
| #define S5K6AA_NUM_SUPPLIES ARRAY_SIZE(s5k6aa_supply_names) | |
| enum s5k6aa_gpio_id { | |
| STBY, | |
| RST, | |
| GPIO_NUM, | |
| }; | |
| struct s5k6aa_regval { | |
| u16 addr; | |
| u16 val; | |
| }; | |
| struct s5k6aa_pixfmt { | |
| u32 code; | |
| u32 colorspace; | |
| /* REG_P_FMT(x) register value */ | |
| u16 reg_p_fmt; | |
| }; | |
| struct s5k6aa_preset { | |
| /* output pixel format and resolution */ | |
| struct v4l2_mbus_framefmt mbus_fmt; | |
| u8 clk_id; | |
| u8 index; | |
| }; | |
| struct s5k6aa_ctrls { | |
| struct v4l2_ctrl_handler handler; | |
| /* Auto / manual white balance cluster */ | |
| struct v4l2_ctrl *awb; | |
| struct v4l2_ctrl *gain_red; | |
| struct v4l2_ctrl *gain_blue; | |
| struct v4l2_ctrl *gain_green; | |
| /* Mirror cluster */ | |
| struct v4l2_ctrl *hflip; | |
| struct v4l2_ctrl *vflip; | |
| /* Auto exposure / manual exposure and gain cluster */ | |
| struct v4l2_ctrl *auto_exp; | |
| struct v4l2_ctrl *exposure; | |
| struct v4l2_ctrl *gain; | |
| }; | |
| struct s5k6aa_interval { | |
| u16 reg_fr_time; | |
| struct v4l2_fract interval; | |
| /* Maximum rectangle for the interval */ | |
| struct v4l2_frmsize_discrete size; | |
| }; | |
| struct s5k6aa { | |
| struct v4l2_subdev sd; | |
| struct media_pad pad; | |
| enum v4l2_mbus_type bus_type; | |
| u8 mipi_lanes; | |
| int (*s_power)(int enable); | |
| struct regulator_bulk_data supplies[S5K6AA_NUM_SUPPLIES]; | |
| struct s5k6aa_gpio gpio[GPIO_NUM]; | |
| /* external master clock frequency */ | |
| unsigned long mclk_frequency; | |
| /* ISP internal master clock frequency */ | |
| u16 clk_fop; | |
| /* output pixel clock frequency range */ | |
| u16 pclk_fmin; | |
| u16 pclk_fmax; | |
| unsigned int inv_hflip:1; | |
| unsigned int inv_vflip:1; | |
| /* protects the struct members below */ | |
| struct mutex lock; | |
| /* sensor matrix scan window */ | |
| struct v4l2_rect ccd_rect; | |
| struct s5k6aa_ctrls ctrls; | |
| struct s5k6aa_preset presets[S5K6AA_MAX_PRESETS]; | |
| struct s5k6aa_preset *preset; | |
| const struct s5k6aa_interval *fiv; | |
| unsigned int streaming:1; | |
| unsigned int apply_cfg:1; | |
| unsigned int apply_crop:1; | |
| unsigned int power; | |
| }; | |
| static struct s5k6aa_regval s5k6aa_analog_config[] = { | |
| /* Analog settings */ | |
| { 0x112a, 0x0000 }, { 0x1132, 0x0000 }, | |
| { 0x113e, 0x0000 }, { 0x115c, 0x0000 }, | |
| { 0x1164, 0x0000 }, { 0x1174, 0x0000 }, | |
| { 0x1178, 0x0000 }, { 0x077a, 0x0000 }, | |
| { 0x077c, 0x0000 }, { 0x077e, 0x0000 }, | |
| { 0x0780, 0x0000 }, { 0x0782, 0x0000 }, | |
| { 0x0784, 0x0000 }, { 0x0786, 0x0000 }, | |
| { 0x0788, 0x0000 }, { 0x07a2, 0x0000 }, | |
| { 0x07a4, 0x0000 }, { 0x07a6, 0x0000 }, | |
| { 0x07a8, 0x0000 }, { 0x07b6, 0x0000 }, | |
| { 0x07b8, 0x0002 }, { 0x07ba, 0x0004 }, | |
| { 0x07bc, 0x0004 }, { 0x07be, 0x0005 }, | |
| { 0x07c0, 0x0005 }, { S5K6AA_TERM, 0 }, | |
| }; | |
| /* TODO: Add RGB888 and Bayer format */ | |
| static const struct s5k6aa_pixfmt s5k6aa_formats[] = { | |
| { MEDIA_BUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_JPEG, 5 }, | |
| /* range 16-240 */ | |
| { MEDIA_BUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_REC709, 6 }, | |
| { MEDIA_BUS_FMT_RGB565_2X8_BE, V4L2_COLORSPACE_JPEG, 0 }, | |
| }; | |
| static const struct s5k6aa_interval s5k6aa_intervals[] = { | |
| { 1000, {10000, 1000000}, {1280, 1024} }, /* 10 fps */ | |
| { 666, {15000, 1000000}, {1280, 1024} }, /* 15 fps */ | |
| { 500, {20000, 1000000}, {1280, 720} }, /* 20 fps */ | |
| { 400, {25000, 1000000}, {640, 480} }, /* 25 fps */ | |
| { 333, {33300, 1000000}, {640, 480} }, /* 30 fps */ | |
| }; | |
| #define S5K6AA_INTERVAL_DEF_INDEX 1 /* 15 fps */ | |
| static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl) | |
| { | |
| return &container_of(ctrl->handler, struct s5k6aa, ctrls.handler)->sd; | |
| } | |
| static inline struct s5k6aa *to_s5k6aa(struct v4l2_subdev *sd) | |
| { | |
| return container_of(sd, struct s5k6aa, sd); | |
| } | |
| /* Set initial values for all preview presets */ | |
| static void s5k6aa_presets_data_init(struct s5k6aa *s5k6aa) | |
| { | |
| struct s5k6aa_preset *preset = &s5k6aa->presets[0]; | |
| int i; | |
| for (i = 0; i < S5K6AA_MAX_PRESETS; i++) { | |
| preset->mbus_fmt.width = S5K6AA_OUT_WIDTH_DEF; | |
| preset->mbus_fmt.height = S5K6AA_OUT_HEIGHT_DEF; | |
| preset->mbus_fmt.code = s5k6aa_formats[0].code; | |
| preset->index = i; | |
| preset->clk_id = 0; | |
| preset++; | |
| } | |
| s5k6aa->fiv = &s5k6aa_intervals[S5K6AA_INTERVAL_DEF_INDEX]; | |
| s5k6aa->preset = &s5k6aa->presets[0]; | |
| } | |
| static int s5k6aa_i2c_read(struct i2c_client *client, u16 addr, u16 *val) | |
| { | |
| u8 wbuf[2] = {addr >> 8, addr & 0xFF}; | |
| struct i2c_msg msg[2]; | |
| u8 rbuf[2]; | |
| int ret; | |
| msg[0].addr = client->addr; | |
| msg[0].flags = 0; | |
| msg[0].len = 2; | |
| msg[0].buf = wbuf; | |
| msg[1].addr = client->addr; | |
| msg[1].flags = I2C_M_RD; | |
| msg[1].len = 2; | |
| msg[1].buf = rbuf; | |
| ret = i2c_transfer(client->adapter, msg, 2); | |
| *val = be16_to_cpu(*((__be16 *)rbuf)); | |
| v4l2_dbg(3, debug, client, "i2c_read: 0x%04X : 0x%04x\n", addr, *val); | |
| return ret == 2 ? 0 : ret; | |
| } | |
| static int s5k6aa_i2c_write(struct i2c_client *client, u16 addr, u16 val) | |
| { | |
| u8 buf[4] = {addr >> 8, addr & 0xFF, val >> 8, val & 0xFF}; | |
| int ret = i2c_master_send(client, buf, 4); | |
| v4l2_dbg(3, debug, client, "i2c_write: 0x%04X : 0x%04x\n", addr, val); | |
| return ret == 4 ? 0 : ret; | |
| } | |
| /* The command register write, assumes Command_Wr_addH = 0x7000. */ | |
| static int s5k6aa_write(struct i2c_client *c, u16 addr, u16 val) | |
| { | |
| int ret = s5k6aa_i2c_write(c, REG_CMDWR_ADDRL, addr); | |
| if (ret) | |
| return ret; | |
| return s5k6aa_i2c_write(c, REG_CMDBUF0_ADDR, val); | |
| } | |
| /* The command register read, assumes Command_Rd_addH = 0x7000. */ | |
| static int s5k6aa_read(struct i2c_client *client, u16 addr, u16 *val) | |
| { | |
| int ret = s5k6aa_i2c_write(client, REG_CMDRD_ADDRL, addr); | |
| if (ret) | |
| return ret; | |
| return s5k6aa_i2c_read(client, REG_CMDBUF0_ADDR, val); | |
| } | |
| static int s5k6aa_write_array(struct v4l2_subdev *sd, | |
| const struct s5k6aa_regval *msg) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(sd); | |
| u16 addr_incr = 0; | |
| int ret = 0; | |
| while (msg->addr != S5K6AA_TERM) { | |
| if (addr_incr != 2) | |
| ret = s5k6aa_i2c_write(client, REG_CMDWR_ADDRL, | |
| msg->addr); | |
| if (ret) | |
| break; | |
| ret = s5k6aa_i2c_write(client, REG_CMDBUF0_ADDR, msg->val); | |
| if (ret) | |
| break; | |
| /* Assume that msg->addr is always less than 0xfffc */ | |
| addr_incr = (msg + 1)->addr - msg->addr; | |
| msg++; | |
| } | |
| return ret; | |
| } | |
| /* Configure the AHB high address bytes for GTG registers access */ | |
| static int s5k6aa_set_ahb_address(struct i2c_client *client) | |
| { | |
| int ret = s5k6aa_i2c_write(client, AHB_MSB_ADDR_PTR, GEN_REG_OFFSH); | |
| if (ret) | |
| return ret; | |
| ret = s5k6aa_i2c_write(client, REG_CMDRD_ADDRH, HOST_SWIF_OFFSH); | |
| if (ret) | |
| return ret; | |
| return s5k6aa_i2c_write(client, REG_CMDWR_ADDRH, HOST_SWIF_OFFSH); | |
| } | |
| /** | |
| * s5k6aa_configure_pixel_clock - apply ISP main clock/PLL configuration | |
| * | |
| * Configure the internal ISP PLL for the required output frequency. | |
| * Locking: called with s5k6aa.lock mutex held. | |
| */ | |
| static int s5k6aa_configure_pixel_clocks(struct s5k6aa *s5k6aa) | |
| { | |
| struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd); | |
| unsigned long fmclk = s5k6aa->mclk_frequency / 1000; | |
| u16 status; | |
| int ret; | |
| if (WARN(fmclk < MIN_MCLK_FREQ_KHZ || fmclk > MAX_MCLK_FREQ_KHZ, | |
| "Invalid clock frequency: %ld\n", fmclk)) | |
| return -EINVAL; | |
| s5k6aa->pclk_fmin = PCLK_FREQ_MIN; | |
| s5k6aa->pclk_fmax = PCLK_FREQ_MAX; | |
| s5k6aa->clk_fop = SYS_PLL_OUT_FREQ; | |
| /* External input clock frequency in kHz */ | |
| ret = s5k6aa_write(c, REG_I_INCLK_FREQ_H, fmclk >> 16); | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_I_INCLK_FREQ_L, fmclk & 0xFFFF); | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_I_USE_NPVI_CLOCKS, 1); | |
| /* Internal PLL frequency */ | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_I_OPCLK_4KHZ(0), s5k6aa->clk_fop); | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_I_MIN_OUTRATE_4KHZ(0), | |
| s5k6aa->pclk_fmin); | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_I_MAX_OUTRATE_4KHZ(0), | |
| s5k6aa->pclk_fmax); | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_I_INIT_PARAMS_UPDATED, 1); | |
| if (!ret) | |
| ret = s5k6aa_read(c, REG_I_ERROR_INFO, &status); | |
| return ret ? ret : (status ? -EINVAL : 0); | |
| } | |
| /* Set horizontal and vertical image flipping */ | |
| static int s5k6aa_set_mirror(struct s5k6aa *s5k6aa, int horiz_flip) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); | |
| int index = s5k6aa->preset->index; | |
| unsigned int vflip = s5k6aa->ctrls.vflip->val ^ s5k6aa->inv_vflip; | |
| unsigned int flip = (horiz_flip ^ s5k6aa->inv_hflip) | (vflip << 1); | |
| return s5k6aa_write(client, REG_P_PREV_MIRROR(index), flip); | |
| } | |
| /* Configure auto/manual white balance and R/G/B gains */ | |
| static int s5k6aa_set_awb(struct s5k6aa *s5k6aa, int awb) | |
| { | |
| struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd); | |
| struct s5k6aa_ctrls *ctrls = &s5k6aa->ctrls; | |
| u16 reg; | |
| int ret = s5k6aa_read(c, REG_DBG_AUTOALG_EN, ®); | |
| if (!ret && !awb) { | |
| ret = s5k6aa_write(c, REG_SF_RGAIN, ctrls->gain_red->val); | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_SF_RGAIN_CHG, 1); | |
| if (ret) | |
| return ret; | |
| ret = s5k6aa_write(c, REG_SF_GGAIN, ctrls->gain_green->val); | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_SF_GGAIN_CHG, 1); | |
| if (ret) | |
| return ret; | |
| ret = s5k6aa_write(c, REG_SF_BGAIN, ctrls->gain_blue->val); | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_SF_BGAIN_CHG, 1); | |
| } | |
| if (!ret) { | |
| reg = awb ? reg | AALG_WB_EN_MASK : reg & ~AALG_WB_EN_MASK; | |
| ret = s5k6aa_write(c, REG_DBG_AUTOALG_EN, reg); | |
| } | |
| return ret; | |
| } | |
| /* Program FW with exposure time, 'exposure' in us units */ | |
| static int s5k6aa_set_user_exposure(struct i2c_client *client, int exposure) | |
| { | |
| unsigned int time = exposure / 10; | |
| int ret = s5k6aa_write(client, REG_SF_USR_EXPOSURE_L, time & 0xffff); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_SF_USR_EXPOSURE_H, time >> 16); | |
| if (ret) | |
| return ret; | |
| return s5k6aa_write(client, REG_SF_USR_EXPOSURE_CHG, 1); | |
| } | |
| static int s5k6aa_set_user_gain(struct i2c_client *client, int gain) | |
| { | |
| int ret = s5k6aa_write(client, REG_SF_USR_TOT_GAIN, gain); | |
| if (ret) | |
| return ret; | |
| return s5k6aa_write(client, REG_SF_USR_TOT_GAIN_CHG, 1); | |
| } | |
| /* Set auto/manual exposure and total gain */ | |
| static int s5k6aa_set_auto_exposure(struct s5k6aa *s5k6aa, int value) | |
| { | |
| struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd); | |
| unsigned int exp_time = s5k6aa->ctrls.exposure->val; | |
| u16 auto_alg; | |
| int ret = s5k6aa_read(c, REG_DBG_AUTOALG_EN, &auto_alg); | |
| if (ret) | |
| return ret; | |
| v4l2_dbg(1, debug, c, "man_exp: %d, auto_exp: %d, a_alg: 0x%x\n", | |
| exp_time, value, auto_alg); | |
| if (value == V4L2_EXPOSURE_AUTO) { | |
| auto_alg |= AALG_AE_EN_MASK | AALG_DIVLEI_EN_MASK; | |
| } else { | |
| ret = s5k6aa_set_user_exposure(c, exp_time); | |
| if (ret) | |
| return ret; | |
| ret = s5k6aa_set_user_gain(c, s5k6aa->ctrls.gain->val); | |
| if (ret) | |
| return ret; | |
| auto_alg &= ~(AALG_AE_EN_MASK | AALG_DIVLEI_EN_MASK); | |
| } | |
| return s5k6aa_write(c, REG_DBG_AUTOALG_EN, auto_alg); | |
| } | |
| static int s5k6aa_set_anti_flicker(struct s5k6aa *s5k6aa, int value) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); | |
| u16 auto_alg; | |
| int ret; | |
| ret = s5k6aa_read(client, REG_DBG_AUTOALG_EN, &auto_alg); | |
| if (ret) | |
| return ret; | |
| if (value == V4L2_CID_POWER_LINE_FREQUENCY_AUTO) { | |
| auto_alg |= AALG_FLICKER_EN_MASK; | |
| } else { | |
| auto_alg &= ~AALG_FLICKER_EN_MASK; | |
| /* The V4L2_CID_LINE_FREQUENCY control values match | |
| * the register values */ | |
| ret = s5k6aa_write(client, REG_SF_FLICKER_QUANT, value); | |
| if (ret) | |
| return ret; | |
| ret = s5k6aa_write(client, REG_SF_FLICKER_QUANT_CHG, 1); | |
| if (ret) | |
| return ret; | |
| } | |
| return s5k6aa_write(client, REG_DBG_AUTOALG_EN, auto_alg); | |
| } | |
| static int s5k6aa_set_colorfx(struct s5k6aa *s5k6aa, int val) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); | |
| static const struct v4l2_control colorfx[] = { | |
| { V4L2_COLORFX_NONE, 0 }, | |
| { V4L2_COLORFX_BW, 1 }, | |
| { V4L2_COLORFX_NEGATIVE, 2 }, | |
| { V4L2_COLORFX_SEPIA, 3 }, | |
| { V4L2_COLORFX_SKY_BLUE, 4 }, | |
| { V4L2_COLORFX_SKETCH, 5 }, | |
| }; | |
| int i; | |
| for (i = 0; i < ARRAY_SIZE(colorfx); i++) { | |
| if (colorfx[i].id == val) | |
| return s5k6aa_write(client, REG_G_SPEC_EFFECTS, | |
| colorfx[i].value); | |
| } | |
| return -EINVAL; | |
| } | |
| static int s5k6aa_preview_config_status(struct i2c_client *client) | |
| { | |
| u16 error = 0; | |
| int ret = s5k6aa_read(client, REG_G_PREV_CFG_ERROR, &error); | |
| v4l2_dbg(1, debug, client, "error: 0x%x (%d)\n", error, ret); | |
| return ret ? ret : (error ? -EINVAL : 0); | |
| } | |
| static int s5k6aa_get_pixfmt_index(struct s5k6aa *s5k6aa, | |
| struct v4l2_mbus_framefmt *mf) | |
| { | |
| unsigned int i; | |
| for (i = 0; i < ARRAY_SIZE(s5k6aa_formats); i++) | |
| if (mf->colorspace == s5k6aa_formats[i].colorspace && | |
| mf->code == s5k6aa_formats[i].code) | |
| return i; | |
| return 0; | |
| } | |
| static int s5k6aa_set_output_framefmt(struct s5k6aa *s5k6aa, | |
| struct s5k6aa_preset *preset) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); | |
| int fmt_index = s5k6aa_get_pixfmt_index(s5k6aa, &preset->mbus_fmt); | |
| int ret; | |
| ret = s5k6aa_write(client, REG_P_OUT_WIDTH(preset->index), | |
| preset->mbus_fmt.width); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_P_OUT_HEIGHT(preset->index), | |
| preset->mbus_fmt.height); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_P_FMT(preset->index), | |
| s5k6aa_formats[fmt_index].reg_p_fmt); | |
| return ret; | |
| } | |
| static int s5k6aa_set_input_params(struct s5k6aa *s5k6aa) | |
| { | |
| struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd); | |
| struct v4l2_rect *r = &s5k6aa->ccd_rect; | |
| int ret; | |
| ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_WIDTH, r->width); | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_HEIGHT, r->height); | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_XOFFS, r->left); | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_YOFFS, r->top); | |
| if (!ret) | |
| ret = s5k6aa_write(c, REG_G_INPUTS_CHANGE_REQ, 1); | |
| if (!ret) | |
| s5k6aa->apply_crop = 0; | |
| return ret; | |
| } | |
| /** | |
| * s5k6aa_configure_video_bus - configure the video output interface | |
| * @bus_type: video bus type: parallel or MIPI-CSI | |
| * @nlanes: number of MIPI lanes to be used (MIPI-CSI only) | |
| * | |
| * Note: Only parallel bus operation has been tested. | |
| */ | |
| static int s5k6aa_configure_video_bus(struct s5k6aa *s5k6aa, | |
| enum v4l2_mbus_type bus_type, int nlanes) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); | |
| u16 cfg = 0; | |
| int ret; | |
| /* | |
| * TODO: The sensor is supposed to support BT.601 and BT.656 | |
| * but there is nothing indicating how to switch between both | |
| * in the datasheet. For now default BT.601 interface is assumed. | |
| */ | |
| if (bus_type == V4L2_MBUS_CSI2) | |
| cfg = nlanes; | |
| else if (bus_type != V4L2_MBUS_PARALLEL) | |
| return -EINVAL; | |
| ret = s5k6aa_write(client, REG_OIF_EN_MIPI_LANES, cfg); | |
| if (ret) | |
| return ret; | |
| return s5k6aa_write(client, REG_OIF_CFG_CHG, 1); | |
| } | |
| /* This function should be called when switching to new user configuration set*/ | |
| static int s5k6aa_new_config_sync(struct i2c_client *client, int timeout, | |
| int cid) | |
| { | |
| unsigned long end = jiffies + msecs_to_jiffies(timeout); | |
| u16 reg = 1; | |
| int ret; | |
| ret = s5k6aa_write(client, REG_G_ACTIVE_PREV_CFG, cid); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_G_NEW_CFG_SYNC, 1); | |
| if (timeout == 0) | |
| return ret; | |
| while (ret >= 0 && time_is_after_jiffies(end)) { | |
| ret = s5k6aa_read(client, REG_G_NEW_CFG_SYNC, ®); | |
| if (!reg) | |
| return 0; | |
| usleep_range(1000, 5000); | |
| } | |
| return ret ? ret : -ETIMEDOUT; | |
| } | |
| /** | |
| * s5k6aa_set_prev_config - write user preview register set | |
| * | |
| * Configure output resolution and color fromat, pixel clock | |
| * frequency range, device frame rate type and frame period range. | |
| */ | |
| static int s5k6aa_set_prev_config(struct s5k6aa *s5k6aa, | |
| struct s5k6aa_preset *preset) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); | |
| int idx = preset->index; | |
| u16 frame_rate_q; | |
| int ret; | |
| if (s5k6aa->fiv->reg_fr_time >= S5K6AA_MAX_HIGHRES_FR_TIME) | |
| frame_rate_q = FR_RATE_Q_BEST_FRRATE; | |
| else | |
| frame_rate_q = FR_RATE_Q_BEST_QUALITY; | |
| ret = s5k6aa_set_output_framefmt(s5k6aa, preset); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_P_MAX_OUT_RATE(idx), | |
| s5k6aa->pclk_fmax); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_P_MIN_OUT_RATE(idx), | |
| s5k6aa->pclk_fmin); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_P_CLK_INDEX(idx), | |
| preset->clk_id); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_P_FR_RATE_TYPE(idx), | |
| FR_RATE_DYNAMIC); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_P_FR_RATE_Q_TYPE(idx), | |
| frame_rate_q); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_P_MAX_FR_TIME(idx), | |
| s5k6aa->fiv->reg_fr_time + 33); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_P_MIN_FR_TIME(idx), | |
| s5k6aa->fiv->reg_fr_time - 33); | |
| if (!ret) | |
| ret = s5k6aa_new_config_sync(client, 250, idx); | |
| if (!ret) | |
| ret = s5k6aa_preview_config_status(client); | |
| if (!ret) | |
| s5k6aa->apply_cfg = 0; | |
| v4l2_dbg(1, debug, client, "Frame interval: %d +/- 3.3ms. (%d)\n", | |
| s5k6aa->fiv->reg_fr_time, ret); | |
| return ret; | |
| } | |
| /** | |
| * s5k6aa_initialize_isp - basic ISP MCU initialization | |
| * | |
| * Configure AHB addresses for registers read/write; configure PLLs for | |
| * required output pixel clock. The ISP power supply needs to be already | |
| * enabled, with an optional H/W reset. | |
| * Locking: called with s5k6aa.lock mutex held. | |
| */ | |
| static int s5k6aa_initialize_isp(struct v4l2_subdev *sd) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(sd); | |
| struct s5k6aa *s5k6aa = to_s5k6aa(sd); | |
| int ret; | |
| s5k6aa->apply_crop = 1; | |
| s5k6aa->apply_cfg = 1; | |
| msleep(100); | |
| ret = s5k6aa_set_ahb_address(client); | |
| if (ret) | |
| return ret; | |
| ret = s5k6aa_configure_video_bus(s5k6aa, s5k6aa->bus_type, | |
| s5k6aa->mipi_lanes); | |
| if (ret) | |
| return ret; | |
| ret = s5k6aa_write_array(sd, s5k6aa_analog_config); | |
| if (ret) | |
| return ret; | |
| msleep(20); | |
| return s5k6aa_configure_pixel_clocks(s5k6aa); | |
| } | |
| static int s5k6aa_gpio_set_value(struct s5k6aa *priv, int id, u32 val) | |
| { | |
| if (!gpio_is_valid(priv->gpio[id].gpio)) | |
| return 0; | |
| gpio_set_value(priv->gpio[id].gpio, !!val); | |
| return 1; | |
| } | |
| static int s5k6aa_gpio_assert(struct s5k6aa *priv, int id) | |
| { | |
| return s5k6aa_gpio_set_value(priv, id, priv->gpio[id].level); | |
| } | |
| static int s5k6aa_gpio_deassert(struct s5k6aa *priv, int id) | |
| { | |
| return s5k6aa_gpio_set_value(priv, id, !priv->gpio[id].level); | |
| } | |
| static int __s5k6aa_power_on(struct s5k6aa *s5k6aa) | |
| { | |
| int ret; | |
| ret = regulator_bulk_enable(S5K6AA_NUM_SUPPLIES, s5k6aa->supplies); | |
| if (ret) | |
| return ret; | |
| if (s5k6aa_gpio_deassert(s5k6aa, STBY)) | |
| usleep_range(150, 200); | |
| if (s5k6aa->s_power) | |
| ret = s5k6aa->s_power(1); | |
| usleep_range(4000, 5000); | |
| if (s5k6aa_gpio_deassert(s5k6aa, RST)) | |
| msleep(20); | |
| return ret; | |
| } | |
| static int __s5k6aa_power_off(struct s5k6aa *s5k6aa) | |
| { | |
| int ret; | |
| if (s5k6aa_gpio_assert(s5k6aa, RST)) | |
| usleep_range(100, 150); | |
| if (s5k6aa->s_power) { | |
| ret = s5k6aa->s_power(0); | |
| if (ret) | |
| return ret; | |
| } | |
| if (s5k6aa_gpio_assert(s5k6aa, STBY)) | |
| usleep_range(50, 100); | |
| s5k6aa->streaming = 0; | |
| return regulator_bulk_disable(S5K6AA_NUM_SUPPLIES, s5k6aa->supplies); | |
| } | |
| /* | |
| * V4L2 subdev core and video operations | |
| */ | |
| static int s5k6aa_set_power(struct v4l2_subdev *sd, int on) | |
| { | |
| struct s5k6aa *s5k6aa = to_s5k6aa(sd); | |
| int ret = 0; | |
| mutex_lock(&s5k6aa->lock); | |
| if (s5k6aa->power == !on) { | |
| if (on) { | |
| ret = __s5k6aa_power_on(s5k6aa); | |
| if (!ret) | |
| ret = s5k6aa_initialize_isp(sd); | |
| } else { | |
| ret = __s5k6aa_power_off(s5k6aa); | |
| } | |
| if (!ret) | |
| s5k6aa->power += on ? 1 : -1; | |
| } | |
| mutex_unlock(&s5k6aa->lock); | |
| if (!on || ret || s5k6aa->power != 1) | |
| return ret; | |
| return v4l2_ctrl_handler_setup(sd->ctrl_handler); | |
| } | |
| static int __s5k6aa_stream(struct s5k6aa *s5k6aa, int enable) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); | |
| int ret = 0; | |
| ret = s5k6aa_write(client, REG_G_ENABLE_PREV, enable); | |
| if (!ret) | |
| ret = s5k6aa_write(client, REG_G_ENABLE_PREV_CHG, 1); | |
| if (!ret) | |
| s5k6aa->streaming = enable; | |
| return ret; | |
| } | |
| static int s5k6aa_s_stream(struct v4l2_subdev *sd, int on) | |
| { | |
| struct s5k6aa *s5k6aa = to_s5k6aa(sd); | |
| int ret = 0; | |
| mutex_lock(&s5k6aa->lock); | |
| if (s5k6aa->streaming == !on) { | |
| if (!ret && s5k6aa->apply_cfg) | |
| ret = s5k6aa_set_prev_config(s5k6aa, s5k6aa->preset); | |
| if (s5k6aa->apply_crop) | |
| ret = s5k6aa_set_input_params(s5k6aa); | |
| if (!ret) | |
| ret = __s5k6aa_stream(s5k6aa, !!on); | |
| } | |
| mutex_unlock(&s5k6aa->lock); | |
| return ret; | |
| } | |
| static int s5k6aa_g_frame_interval(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_frame_interval *fi) | |
| { | |
| struct s5k6aa *s5k6aa = to_s5k6aa(sd); | |
| mutex_lock(&s5k6aa->lock); | |
| fi->interval = s5k6aa->fiv->interval; | |
| mutex_unlock(&s5k6aa->lock); | |
| return 0; | |
| } | |
| static int __s5k6aa_set_frame_interval(struct s5k6aa *s5k6aa, | |
| struct v4l2_subdev_frame_interval *fi) | |
| { | |
| struct v4l2_mbus_framefmt *mbus_fmt = &s5k6aa->preset->mbus_fmt; | |
| const struct s5k6aa_interval *fiv = &s5k6aa_intervals[0]; | |
| unsigned int err, min_err = UINT_MAX; | |
| unsigned int i, fr_time; | |
| if (fi->interval.denominator == 0) | |
| return -EINVAL; | |
| fr_time = fi->interval.numerator * 10000 / fi->interval.denominator; | |
| for (i = 0; i < ARRAY_SIZE(s5k6aa_intervals); i++) { | |
| const struct s5k6aa_interval *iv = &s5k6aa_intervals[i]; | |
| if (mbus_fmt->width > iv->size.width || | |
| mbus_fmt->height > iv->size.height) | |
| continue; | |
| err = abs(iv->reg_fr_time - fr_time); | |
| if (err < min_err) { | |
| fiv = iv; | |
| min_err = err; | |
| } | |
| } | |
| s5k6aa->fiv = fiv; | |
| v4l2_dbg(1, debug, &s5k6aa->sd, "Changed frame interval to %d us\n", | |
| fiv->reg_fr_time * 100); | |
| return 0; | |
| } | |
| static int s5k6aa_s_frame_interval(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_frame_interval *fi) | |
| { | |
| struct s5k6aa *s5k6aa = to_s5k6aa(sd); | |
| int ret; | |
| v4l2_dbg(1, debug, sd, "Setting %d/%d frame interval\n", | |
| fi->interval.numerator, fi->interval.denominator); | |
| mutex_lock(&s5k6aa->lock); | |
| ret = __s5k6aa_set_frame_interval(s5k6aa, fi); | |
| s5k6aa->apply_cfg = 1; | |
| mutex_unlock(&s5k6aa->lock); | |
| return ret; | |
| } | |
| /* | |
| * V4L2 subdev pad level and video operations | |
| */ | |
| static int s5k6aa_enum_frame_interval(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_pad_config *cfg, | |
| struct v4l2_subdev_frame_interval_enum *fie) | |
| { | |
| struct s5k6aa *s5k6aa = to_s5k6aa(sd); | |
| const struct s5k6aa_interval *fi; | |
| int ret = 0; | |
| if (fie->index >= ARRAY_SIZE(s5k6aa_intervals)) | |
| return -EINVAL; | |
| v4l_bound_align_image(&fie->width, S5K6AA_WIN_WIDTH_MIN, | |
| S5K6AA_WIN_WIDTH_MAX, 1, | |
| &fie->height, S5K6AA_WIN_HEIGHT_MIN, | |
| S5K6AA_WIN_HEIGHT_MAX, 1, 0); | |
| mutex_lock(&s5k6aa->lock); | |
| fi = &s5k6aa_intervals[fie->index]; | |
| if (fie->width > fi->size.width || fie->height > fi->size.height) | |
| ret = -EINVAL; | |
| else | |
| fie->interval = fi->interval; | |
| mutex_unlock(&s5k6aa->lock); | |
| return ret; | |
| } | |
| static int s5k6aa_enum_mbus_code(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_pad_config *cfg, | |
| struct v4l2_subdev_mbus_code_enum *code) | |
| { | |
| if (code->index >= ARRAY_SIZE(s5k6aa_formats)) | |
| return -EINVAL; | |
| code->code = s5k6aa_formats[code->index].code; | |
| return 0; | |
| } | |
| static int s5k6aa_enum_frame_size(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_pad_config *cfg, | |
| struct v4l2_subdev_frame_size_enum *fse) | |
| { | |
| int i = ARRAY_SIZE(s5k6aa_formats); | |
| if (fse->index > 0) | |
| return -EINVAL; | |
| while (--i) | |
| if (fse->code == s5k6aa_formats[i].code) | |
| break; | |
| fse->code = s5k6aa_formats[i].code; | |
| fse->min_width = S5K6AA_WIN_WIDTH_MIN; | |
| fse->max_width = S5K6AA_WIN_WIDTH_MAX; | |
| fse->max_height = S5K6AA_WIN_HEIGHT_MIN; | |
| fse->min_height = S5K6AA_WIN_HEIGHT_MAX; | |
| return 0; | |
| } | |
| static struct v4l2_rect * | |
| __s5k6aa_get_crop_rect(struct s5k6aa *s5k6aa, struct v4l2_subdev_pad_config *cfg, | |
| enum v4l2_subdev_format_whence which) | |
| { | |
| if (which == V4L2_SUBDEV_FORMAT_ACTIVE) | |
| return &s5k6aa->ccd_rect; | |
| WARN_ON(which != V4L2_SUBDEV_FORMAT_TRY); | |
| return v4l2_subdev_get_try_crop(&s5k6aa->sd, cfg, 0); | |
| } | |
| static void s5k6aa_try_format(struct s5k6aa *s5k6aa, | |
| struct v4l2_mbus_framefmt *mf) | |
| { | |
| unsigned int index; | |
| v4l_bound_align_image(&mf->width, S5K6AA_WIN_WIDTH_MIN, | |
| S5K6AA_WIN_WIDTH_MAX, 1, | |
| &mf->height, S5K6AA_WIN_HEIGHT_MIN, | |
| S5K6AA_WIN_HEIGHT_MAX, 1, 0); | |
| if (mf->colorspace != V4L2_COLORSPACE_JPEG && | |
| mf->colorspace != V4L2_COLORSPACE_REC709) | |
| mf->colorspace = V4L2_COLORSPACE_JPEG; | |
| index = s5k6aa_get_pixfmt_index(s5k6aa, mf); | |
| mf->colorspace = s5k6aa_formats[index].colorspace; | |
| mf->code = s5k6aa_formats[index].code; | |
| mf->field = V4L2_FIELD_NONE; | |
| } | |
| static int s5k6aa_get_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_pad_config *cfg, | |
| struct v4l2_subdev_format *fmt) | |
| { | |
| struct s5k6aa *s5k6aa = to_s5k6aa(sd); | |
| struct v4l2_mbus_framefmt *mf; | |
| memset(fmt->reserved, 0, sizeof(fmt->reserved)); | |
| if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { | |
| mf = v4l2_subdev_get_try_format(sd, cfg, 0); | |
| fmt->format = *mf; | |
| return 0; | |
| } | |
| mutex_lock(&s5k6aa->lock); | |
| fmt->format = s5k6aa->preset->mbus_fmt; | |
| mutex_unlock(&s5k6aa->lock); | |
| return 0; | |
| } | |
| static int s5k6aa_set_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_pad_config *cfg, | |
| struct v4l2_subdev_format *fmt) | |
| { | |
| struct s5k6aa *s5k6aa = to_s5k6aa(sd); | |
| struct s5k6aa_preset *preset = s5k6aa->preset; | |
| struct v4l2_mbus_framefmt *mf; | |
| struct v4l2_rect *crop; | |
| int ret = 0; | |
| mutex_lock(&s5k6aa->lock); | |
| s5k6aa_try_format(s5k6aa, &fmt->format); | |
| if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { | |
| mf = v4l2_subdev_get_try_format(sd, cfg, fmt->pad); | |
| crop = v4l2_subdev_get_try_crop(sd, cfg, 0); | |
| } else { | |
| if (s5k6aa->streaming) { | |
| ret = -EBUSY; | |
| } else { | |
| mf = &preset->mbus_fmt; | |
| crop = &s5k6aa->ccd_rect; | |
| s5k6aa->apply_cfg = 1; | |
| } | |
| } | |
| if (ret == 0) { | |
| struct v4l2_subdev_frame_interval fiv = { | |
| .interval = {0, 1} | |
| }; | |
| *mf = fmt->format; | |
| /* | |
| * Make sure the crop window is valid, i.e. its size is | |
| * greater than the output window, as the ISP supports | |
| * only down-scaling. | |
| */ | |
| crop->width = clamp_t(unsigned int, crop->width, mf->width, | |
| S5K6AA_WIN_WIDTH_MAX); | |
| crop->height = clamp_t(unsigned int, crop->height, mf->height, | |
| S5K6AA_WIN_HEIGHT_MAX); | |
| crop->left = clamp_t(unsigned int, crop->left, 0, | |
| S5K6AA_WIN_WIDTH_MAX - crop->width); | |
| crop->top = clamp_t(unsigned int, crop->top, 0, | |
| S5K6AA_WIN_HEIGHT_MAX - crop->height); | |
| /* Reset to minimum possible frame interval */ | |
| ret = __s5k6aa_set_frame_interval(s5k6aa, &fiv); | |
| } | |
| mutex_unlock(&s5k6aa->lock); | |
| return ret; | |
| } | |
| static int s5k6aa_get_selection(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_pad_config *cfg, | |
| struct v4l2_subdev_selection *sel) | |
| { | |
| struct s5k6aa *s5k6aa = to_s5k6aa(sd); | |
| struct v4l2_rect *rect; | |
| if (sel->target != V4L2_SEL_TGT_CROP) | |
| return -EINVAL; | |
| memset(sel->reserved, 0, sizeof(sel->reserved)); | |
| mutex_lock(&s5k6aa->lock); | |
| rect = __s5k6aa_get_crop_rect(s5k6aa, cfg, sel->which); | |
| sel->r = *rect; | |
| mutex_unlock(&s5k6aa->lock); | |
| v4l2_dbg(1, debug, sd, "Current crop rectangle: (%d,%d)/%dx%d\n", | |
| rect->left, rect->top, rect->width, rect->height); | |
| return 0; | |
| } | |
| static int s5k6aa_set_selection(struct v4l2_subdev *sd, | |
| struct v4l2_subdev_pad_config *cfg, | |
| struct v4l2_subdev_selection *sel) | |
| { | |
| struct s5k6aa *s5k6aa = to_s5k6aa(sd); | |
| struct v4l2_mbus_framefmt *mf; | |
| unsigned int max_x, max_y; | |
| struct v4l2_rect *crop_r; | |
| if (sel->target != V4L2_SEL_TGT_CROP) | |
| return -EINVAL; | |
| mutex_lock(&s5k6aa->lock); | |
| crop_r = __s5k6aa_get_crop_rect(s5k6aa, cfg, sel->which); | |
| if (sel->which == V4L2_SUBDEV_FORMAT_ACTIVE) { | |
| mf = &s5k6aa->preset->mbus_fmt; | |
| s5k6aa->apply_crop = 1; | |
| } else { | |
| mf = v4l2_subdev_get_try_format(sd, cfg, 0); | |
| } | |
| v4l_bound_align_image(&sel->r.width, mf->width, | |
| S5K6AA_WIN_WIDTH_MAX, 1, | |
| &sel->r.height, mf->height, | |
| S5K6AA_WIN_HEIGHT_MAX, 1, 0); | |
| max_x = (S5K6AA_WIN_WIDTH_MAX - sel->r.width) & ~1; | |
| max_y = (S5K6AA_WIN_HEIGHT_MAX - sel->r.height) & ~1; | |
| sel->r.left = clamp_t(unsigned int, sel->r.left, 0, max_x); | |
| sel->r.top = clamp_t(unsigned int, sel->r.top, 0, max_y); | |
| *crop_r = sel->r; | |
| mutex_unlock(&s5k6aa->lock); | |
| v4l2_dbg(1, debug, sd, "Set crop rectangle: (%d,%d)/%dx%d\n", | |
| crop_r->left, crop_r->top, crop_r->width, crop_r->height); | |
| return 0; | |
| } | |
| static const struct v4l2_subdev_pad_ops s5k6aa_pad_ops = { | |
| .enum_mbus_code = s5k6aa_enum_mbus_code, | |
| .enum_frame_size = s5k6aa_enum_frame_size, | |
| .enum_frame_interval = s5k6aa_enum_frame_interval, | |
| .get_fmt = s5k6aa_get_fmt, | |
| .set_fmt = s5k6aa_set_fmt, | |
| .get_selection = s5k6aa_get_selection, | |
| .set_selection = s5k6aa_set_selection, | |
| }; | |
| static const struct v4l2_subdev_video_ops s5k6aa_video_ops = { | |
| .g_frame_interval = s5k6aa_g_frame_interval, | |
| .s_frame_interval = s5k6aa_s_frame_interval, | |
| .s_stream = s5k6aa_s_stream, | |
| }; | |
| /* | |
| * V4L2 subdev controls | |
| */ | |
| static int s5k6aa_s_ctrl(struct v4l2_ctrl *ctrl) | |
| { | |
| struct v4l2_subdev *sd = ctrl_to_sd(ctrl); | |
| struct i2c_client *client = v4l2_get_subdevdata(sd); | |
| struct s5k6aa *s5k6aa = to_s5k6aa(sd); | |
| int idx, err = 0; | |
| v4l2_dbg(1, debug, sd, "ctrl: 0x%x, value: %d\n", ctrl->id, ctrl->val); | |
| mutex_lock(&s5k6aa->lock); | |
| /* | |
| * If the device is not powered up by the host driver do | |
| * not apply any controls to H/W at this time. Instead | |
| * the controls will be restored right after power-up. | |
| */ | |
| if (s5k6aa->power == 0) | |
| goto unlock; | |
| idx = s5k6aa->preset->index; | |
| switch (ctrl->id) { | |
| case V4L2_CID_AUTO_WHITE_BALANCE: | |
| err = s5k6aa_set_awb(s5k6aa, ctrl->val); | |
| break; | |
| case V4L2_CID_BRIGHTNESS: | |
| err = s5k6aa_write(client, REG_USER_BRIGHTNESS, ctrl->val); | |
| break; | |
| case V4L2_CID_COLORFX: | |
| err = s5k6aa_set_colorfx(s5k6aa, ctrl->val); | |
| break; | |
| case V4L2_CID_CONTRAST: | |
| err = s5k6aa_write(client, REG_USER_CONTRAST, ctrl->val); | |
| break; | |
| case V4L2_CID_EXPOSURE_AUTO: | |
| err = s5k6aa_set_auto_exposure(s5k6aa, ctrl->val); | |
| break; | |
| case V4L2_CID_HFLIP: | |
| err = s5k6aa_set_mirror(s5k6aa, ctrl->val); | |
| if (err) | |
| break; | |
| err = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1); | |
| break; | |
| case V4L2_CID_POWER_LINE_FREQUENCY: | |
| err = s5k6aa_set_anti_flicker(s5k6aa, ctrl->val); | |
| break; | |
| case V4L2_CID_SATURATION: | |
| err = s5k6aa_write(client, REG_USER_SATURATION, ctrl->val); | |
| break; | |
| case V4L2_CID_SHARPNESS: | |
| err = s5k6aa_write(client, REG_USER_SHARPBLUR, ctrl->val); | |
| break; | |
| case V4L2_CID_WHITE_BALANCE_TEMPERATURE: | |
| err = s5k6aa_write(client, REG_P_COLORTEMP(idx), ctrl->val); | |
| if (err) | |
| break; | |
| err = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1); | |
| break; | |
| } | |
| unlock: | |
| mutex_unlock(&s5k6aa->lock); | |
| return err; | |
| } | |
| static const struct v4l2_ctrl_ops s5k6aa_ctrl_ops = { | |
| .s_ctrl = s5k6aa_s_ctrl, | |
| }; | |
| static int s5k6aa_log_status(struct v4l2_subdev *sd) | |
| { | |
| v4l2_ctrl_handler_log_status(sd->ctrl_handler, sd->name); | |
| return 0; | |
| } | |
| #define V4L2_CID_RED_GAIN (V4L2_CTRL_CLASS_CAMERA | 0x1001) | |
| #define V4L2_CID_GREEN_GAIN (V4L2_CTRL_CLASS_CAMERA | 0x1002) | |
| #define V4L2_CID_BLUE_GAIN (V4L2_CTRL_CLASS_CAMERA | 0x1003) | |
| static const struct v4l2_ctrl_config s5k6aa_ctrls[] = { | |
| { | |
| .ops = &s5k6aa_ctrl_ops, | |
| .id = V4L2_CID_RED_GAIN, | |
| .type = V4L2_CTRL_TYPE_INTEGER, | |
| .name = "Gain, Red", | |
| .min = 0, | |
| .max = 256, | |
| .def = 127, | |
| .step = 1, | |
| }, { | |
| .ops = &s5k6aa_ctrl_ops, | |
| .id = V4L2_CID_GREEN_GAIN, | |
| .type = V4L2_CTRL_TYPE_INTEGER, | |
| .name = "Gain, Green", | |
| .min = 0, | |
| .max = 256, | |
| .def = 127, | |
| .step = 1, | |
| }, { | |
| .ops = &s5k6aa_ctrl_ops, | |
| .id = V4L2_CID_BLUE_GAIN, | |
| .type = V4L2_CTRL_TYPE_INTEGER, | |
| .name = "Gain, Blue", | |
| .min = 0, | |
| .max = 256, | |
| .def = 127, | |
| .step = 1, | |
| }, | |
| }; | |
| static int s5k6aa_initialize_ctrls(struct s5k6aa *s5k6aa) | |
| { | |
| const struct v4l2_ctrl_ops *ops = &s5k6aa_ctrl_ops; | |
| struct s5k6aa_ctrls *ctrls = &s5k6aa->ctrls; | |
| struct v4l2_ctrl_handler *hdl = &ctrls->handler; | |
| int ret = v4l2_ctrl_handler_init(hdl, 16); | |
| if (ret) | |
| return ret; | |
| /* Auto white balance cluster */ | |
| ctrls->awb = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_AUTO_WHITE_BALANCE, | |
| 0, 1, 1, 1); | |
| ctrls->gain_red = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[0], NULL); | |
| ctrls->gain_green = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[1], NULL); | |
| ctrls->gain_blue = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[2], NULL); | |
| v4l2_ctrl_auto_cluster(4, &ctrls->awb, 0, false); | |
| ctrls->hflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HFLIP, 0, 1, 1, 0); | |
| ctrls->vflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VFLIP, 0, 1, 1, 0); | |
| v4l2_ctrl_cluster(2, &ctrls->hflip); | |
| ctrls->auto_exp = v4l2_ctrl_new_std_menu(hdl, ops, | |
| V4L2_CID_EXPOSURE_AUTO, | |
| V4L2_EXPOSURE_MANUAL, 0, V4L2_EXPOSURE_AUTO); | |
| /* Exposure time: x 1 us */ | |
| ctrls->exposure = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_EXPOSURE, | |
| 0, 6000000U, 1, 100000U); | |
| /* Total gain: 256 <=> 1x */ | |
| ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN, | |
| 0, 256, 1, 256); | |
| v4l2_ctrl_auto_cluster(3, &ctrls->auto_exp, 0, false); | |
| v4l2_ctrl_new_std_menu(hdl, ops, V4L2_CID_POWER_LINE_FREQUENCY, | |
| V4L2_CID_POWER_LINE_FREQUENCY_AUTO, 0, | |
| V4L2_CID_POWER_LINE_FREQUENCY_AUTO); | |
| v4l2_ctrl_new_std_menu(hdl, ops, V4L2_CID_COLORFX, | |
| V4L2_COLORFX_SKY_BLUE, ~0x6f, V4L2_COLORFX_NONE); | |
| v4l2_ctrl_new_std(hdl, ops, V4L2_CID_WHITE_BALANCE_TEMPERATURE, | |
| 0, 256, 1, 0); | |
| v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SATURATION, -127, 127, 1, 0); | |
| v4l2_ctrl_new_std(hdl, ops, V4L2_CID_BRIGHTNESS, -127, 127, 1, 0); | |
| v4l2_ctrl_new_std(hdl, ops, V4L2_CID_CONTRAST, -127, 127, 1, 0); | |
| v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SHARPNESS, -127, 127, 1, 0); | |
| if (hdl->error) { | |
| ret = hdl->error; | |
| v4l2_ctrl_handler_free(hdl); | |
| return ret; | |
| } | |
| s5k6aa->sd.ctrl_handler = hdl; | |
| return 0; | |
| } | |
| /* | |
| * V4L2 subdev internal operations | |
| */ | |
| static int s5k6aa_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) | |
| { | |
| struct v4l2_mbus_framefmt *format = v4l2_subdev_get_try_format(sd, fh->pad, 0); | |
| struct v4l2_rect *crop = v4l2_subdev_get_try_crop(sd, fh->pad, 0); | |
| format->colorspace = s5k6aa_formats[0].colorspace; | |
| format->code = s5k6aa_formats[0].code; | |
| format->width = S5K6AA_OUT_WIDTH_DEF; | |
| format->height = S5K6AA_OUT_HEIGHT_DEF; | |
| format->field = V4L2_FIELD_NONE; | |
| crop->width = S5K6AA_WIN_WIDTH_MAX; | |
| crop->height = S5K6AA_WIN_HEIGHT_MAX; | |
| crop->left = 0; | |
| crop->top = 0; | |
| return 0; | |
| } | |
| static int s5k6aa_check_fw_revision(struct s5k6aa *s5k6aa) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); | |
| u16 api_ver = 0, fw_rev = 0; | |
| int ret = s5k6aa_set_ahb_address(client); | |
| if (!ret) | |
| ret = s5k6aa_read(client, REG_FW_APIVER, &api_ver); | |
| if (!ret) | |
| ret = s5k6aa_read(client, REG_FW_REVISION, &fw_rev); | |
| if (ret) { | |
| v4l2_err(&s5k6aa->sd, "FW revision check failed!\n"); | |
| return ret; | |
| } | |
| v4l2_info(&s5k6aa->sd, "FW API ver.: 0x%X, FW rev.: 0x%X\n", | |
| api_ver, fw_rev); | |
| return api_ver == S5K6AAFX_FW_APIVER ? 0 : -ENODEV; | |
| } | |
| static int s5k6aa_registered(struct v4l2_subdev *sd) | |
| { | |
| struct s5k6aa *s5k6aa = to_s5k6aa(sd); | |
| int ret; | |
| mutex_lock(&s5k6aa->lock); | |
| ret = __s5k6aa_power_on(s5k6aa); | |
| if (!ret) { | |
| msleep(100); | |
| ret = s5k6aa_check_fw_revision(s5k6aa); | |
| __s5k6aa_power_off(s5k6aa); | |
| } | |
| mutex_unlock(&s5k6aa->lock); | |
| return ret; | |
| } | |
| static const struct v4l2_subdev_internal_ops s5k6aa_subdev_internal_ops = { | |
| .registered = s5k6aa_registered, | |
| .open = s5k6aa_open, | |
| }; | |
| static const struct v4l2_subdev_core_ops s5k6aa_core_ops = { | |
| .s_power = s5k6aa_set_power, | |
| .log_status = s5k6aa_log_status, | |
| }; | |
| static const struct v4l2_subdev_ops s5k6aa_subdev_ops = { | |
| .core = &s5k6aa_core_ops, | |
| .pad = &s5k6aa_pad_ops, | |
| .video = &s5k6aa_video_ops, | |
| }; | |
| /* | |
| * GPIO setup | |
| */ | |
| static int s5k6aa_configure_gpios(struct s5k6aa *s5k6aa, | |
| const struct s5k6aa_platform_data *pdata) | |
| { | |
| struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); | |
| const struct s5k6aa_gpio *gpio; | |
| unsigned long flags; | |
| int ret; | |
| s5k6aa->gpio[STBY].gpio = -EINVAL; | |
| s5k6aa->gpio[RST].gpio = -EINVAL; | |
| gpio = &pdata->gpio_stby; | |
| if (gpio_is_valid(gpio->gpio)) { | |
| flags = (gpio->level ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW) | |
| | GPIOF_EXPORT; | |
| ret = devm_gpio_request_one(&client->dev, gpio->gpio, flags, | |
| "S5K6AA_STBY"); | |
| if (ret < 0) | |
| return ret; | |
| s5k6aa->gpio[STBY] = *gpio; | |
| } | |
| gpio = &pdata->gpio_reset; | |
| if (gpio_is_valid(gpio->gpio)) { | |
| flags = (gpio->level ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW) | |
| | GPIOF_EXPORT; | |
| ret = devm_gpio_request_one(&client->dev, gpio->gpio, flags, | |
| "S5K6AA_RST"); | |
| if (ret < 0) | |
| return ret; | |
| s5k6aa->gpio[RST] = *gpio; | |
| } | |
| return 0; | |
| } | |
| static int s5k6aa_probe(struct i2c_client *client, | |
| const struct i2c_device_id *id) | |
| { | |
| const struct s5k6aa_platform_data *pdata = client->dev.platform_data; | |
| struct v4l2_subdev *sd; | |
| struct s5k6aa *s5k6aa; | |
| int i, ret; | |
| if (pdata == NULL) { | |
| dev_err(&client->dev, "Platform data not specified\n"); | |
| return -EINVAL; | |
| } | |
| if (pdata->mclk_frequency == 0) { | |
| dev_err(&client->dev, "MCLK frequency not specified\n"); | |
| return -EINVAL; | |
| } | |
| s5k6aa = devm_kzalloc(&client->dev, sizeof(*s5k6aa), GFP_KERNEL); | |
| if (!s5k6aa) | |
| return -ENOMEM; | |
| mutex_init(&s5k6aa->lock); | |
| s5k6aa->mclk_frequency = pdata->mclk_frequency; | |
| s5k6aa->bus_type = pdata->bus_type; | |
| s5k6aa->mipi_lanes = pdata->nlanes; | |
| s5k6aa->s_power = pdata->set_power; | |
| s5k6aa->inv_hflip = pdata->horiz_flip; | |
| s5k6aa->inv_vflip = pdata->vert_flip; | |
| sd = &s5k6aa->sd; | |
| v4l2_i2c_subdev_init(sd, client, &s5k6aa_subdev_ops); | |
| strlcpy(sd->name, DRIVER_NAME, sizeof(sd->name)); | |
| sd->internal_ops = &s5k6aa_subdev_internal_ops; | |
| sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; | |
| s5k6aa->pad.flags = MEDIA_PAD_FL_SOURCE; | |
| sd->entity.function = MEDIA_ENT_F_CAM_SENSOR; | |
| ret = media_entity_pads_init(&sd->entity, 1, &s5k6aa->pad); | |
| if (ret) | |
| return ret; | |
| ret = s5k6aa_configure_gpios(s5k6aa, pdata); | |
| if (ret) | |
| goto out_err; | |
| for (i = 0; i < S5K6AA_NUM_SUPPLIES; i++) | |
| s5k6aa->supplies[i].supply = s5k6aa_supply_names[i]; | |
| ret = devm_regulator_bulk_get(&client->dev, S5K6AA_NUM_SUPPLIES, | |
| s5k6aa->supplies); | |
| if (ret) { | |
| dev_err(&client->dev, "Failed to get regulators\n"); | |
| goto out_err; | |
| } | |
| ret = s5k6aa_initialize_ctrls(s5k6aa); | |
| if (ret) | |
| goto out_err; | |
| s5k6aa_presets_data_init(s5k6aa); | |
| s5k6aa->ccd_rect.width = S5K6AA_WIN_WIDTH_MAX; | |
| s5k6aa->ccd_rect.height = S5K6AA_WIN_HEIGHT_MAX; | |
| s5k6aa->ccd_rect.left = 0; | |
| s5k6aa->ccd_rect.top = 0; | |
| return 0; | |
| out_err: | |
| media_entity_cleanup(&s5k6aa->sd.entity); | |
| return ret; | |
| } | |
| static int s5k6aa_remove(struct i2c_client *client) | |
| { | |
| struct v4l2_subdev *sd = i2c_get_clientdata(client); | |
| v4l2_device_unregister_subdev(sd); | |
| v4l2_ctrl_handler_free(sd->ctrl_handler); | |
| media_entity_cleanup(&sd->entity); | |
| return 0; | |
| } | |
| static const struct i2c_device_id s5k6aa_id[] = { | |
| { DRIVER_NAME, 0 }, | |
| { }, | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, s5k6aa_id); | |
| static struct i2c_driver s5k6aa_i2c_driver = { | |
| .driver = { | |
| .name = DRIVER_NAME | |
| }, | |
| .probe = s5k6aa_probe, | |
| .remove = s5k6aa_remove, | |
| .id_table = s5k6aa_id, | |
| }; | |
| module_i2c_driver(s5k6aa_i2c_driver); | |
| MODULE_DESCRIPTION("Samsung S5K6AA(FX) SXGA camera driver"); | |
| MODULE_AUTHOR("Sylwester Nawrocki <s.nawrocki@samsung.com>"); | |
| MODULE_LICENSE("GPL"); |