|  | /* | 
|  | * GPIO driver for the SMSC SCH311x Super-I/O chips | 
|  | * | 
|  | * Copyright (C) 2013 Bruno Randolf <br1@einfach.org> | 
|  | * | 
|  | * SuperIO functions and chip detection: | 
|  | * (c) Copyright 2008 Wim Van Sebroeck <wim@iguana.be>. | 
|  | * | 
|  | * This program is free software; you can redistribute it and/or modify | 
|  | * it under the terms of the GNU General Public License as published by | 
|  | * the Free Software Foundation; either version 2 of the License, or | 
|  | * (at your option) any later version. | 
|  | */ | 
|  |  | 
|  | #include <linux/ioport.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/kernel.h> | 
|  | #include <linux/init.h> | 
|  | #include <linux/platform_device.h> | 
|  | #include <linux/gpio.h> | 
|  | #include <linux/bitops.h> | 
|  | #include <linux/io.h> | 
|  |  | 
|  | #define DRV_NAME			"gpio-sch311x" | 
|  |  | 
|  | #define SCH311X_GPIO_CONF_OUT		0x00 | 
|  | #define SCH311X_GPIO_CONF_IN		0x01 | 
|  | #define SCH311X_GPIO_CONF_INVERT	0x02 | 
|  | #define SCH311X_GPIO_CONF_OPEN_DRAIN	0x80 | 
|  |  | 
|  | #define SIO_CONFIG_KEY_ENTER		0x55 | 
|  | #define SIO_CONFIG_KEY_EXIT		0xaa | 
|  |  | 
|  | #define GP1				0x4b | 
|  |  | 
|  | static int sch311x_ioports[] = { 0x2e, 0x4e, 0x162e, 0x164e }; | 
|  |  | 
|  | static struct platform_device *sch311x_gpio_pdev; | 
|  |  | 
|  | struct sch311x_pdev_data {		/* platform device data */ | 
|  | unsigned short runtime_reg;	/* runtime register base address */ | 
|  | }; | 
|  |  | 
|  | struct sch311x_gpio_block {		/* one GPIO block runtime data */ | 
|  | struct gpio_chip chip; | 
|  | unsigned short data_reg;	/* from definition below */ | 
|  | unsigned short *config_regs;	/* pointer to definition below */ | 
|  | unsigned short runtime_reg;	/* runtime register */ | 
|  | spinlock_t lock;		/* lock for this GPIO block */ | 
|  | }; | 
|  |  | 
|  | struct sch311x_gpio_priv {		/* driver private data */ | 
|  | struct sch311x_gpio_block blocks[6]; | 
|  | }; | 
|  |  | 
|  | struct sch311x_gpio_block_def {		/* register address definitions */ | 
|  | unsigned short data_reg; | 
|  | unsigned short config_regs[8]; | 
|  | unsigned short base; | 
|  | }; | 
|  |  | 
|  | /* Note: some GPIOs are not available, these are marked with 0x00 */ | 
|  |  | 
|  | static struct sch311x_gpio_block_def sch311x_gpio_blocks[] = { | 
|  | { | 
|  | .data_reg = 0x4b,	/* GP1 */ | 
|  | .config_regs = {0x23, 0x24, 0x25, 0x26, 0x27, 0x29, 0x2a, 0x2b}, | 
|  | .base = 10, | 
|  | }, | 
|  | { | 
|  | .data_reg = 0x4c,	/* GP2 */ | 
|  | .config_regs = {0x00, 0x2c, 0x2d, 0x00, 0x00, 0x00, 0x00, 0x32}, | 
|  | .base = 20, | 
|  | }, | 
|  | { | 
|  | .data_reg = 0x4d,	/* GP3 */ | 
|  | .config_regs = {0x33, 0x34, 0x35, 0x36, 0x37, 0x00, 0x39, 0x3a}, | 
|  | .base = 30, | 
|  | }, | 
|  | { | 
|  | .data_reg = 0x4e,	/* GP4 */ | 
|  | .config_regs = {0x3b, 0x00, 0x3d, 0x00, 0x6e, 0x6f, 0x72, 0x73}, | 
|  | .base = 40, | 
|  | }, | 
|  | { | 
|  | .data_reg = 0x4f,	/* GP5 */ | 
|  | .config_regs = {0x3f, 0x40, 0x41, 0x42, 0x43, 0x44, 0x45, 0x46}, | 
|  | .base = 50, | 
|  | }, | 
|  | { | 
|  | .data_reg = 0x50,	/* GP6 */ | 
|  | .config_regs = {0x47, 0x48, 0x54, 0x55, 0x56, 0x57, 0x58, 0x59}, | 
|  | .base = 60, | 
|  | }, | 
|  | }; | 
|  |  | 
|  | /* | 
|  | *	Super-IO functions | 
|  | */ | 
|  |  | 
|  | static inline int sch311x_sio_enter(int sio_config_port) | 
|  | { | 
|  | /* Don't step on other drivers' I/O space by accident. */ | 
|  | if (!request_muxed_region(sio_config_port, 2, DRV_NAME)) { | 
|  | pr_err(DRV_NAME "I/O address 0x%04x already in use\n", | 
|  | sio_config_port); | 
|  | return -EBUSY; | 
|  | } | 
|  |  | 
|  | outb(SIO_CONFIG_KEY_ENTER, sio_config_port); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static inline void sch311x_sio_exit(int sio_config_port) | 
|  | { | 
|  | outb(SIO_CONFIG_KEY_EXIT, sio_config_port); | 
|  | release_region(sio_config_port, 2); | 
|  | } | 
|  |  | 
|  | static inline int sch311x_sio_inb(int sio_config_port, int reg) | 
|  | { | 
|  | outb(reg, sio_config_port); | 
|  | return inb(sio_config_port + 1); | 
|  | } | 
|  |  | 
|  | static inline void sch311x_sio_outb(int sio_config_port, int reg, int val) | 
|  | { | 
|  | outb(reg, sio_config_port); | 
|  | outb(val, sio_config_port + 1); | 
|  | } | 
|  |  | 
|  |  | 
|  | /* | 
|  | *	GPIO functions | 
|  | */ | 
|  |  | 
|  | static int sch311x_gpio_request(struct gpio_chip *chip, unsigned offset) | 
|  | { | 
|  | struct sch311x_gpio_block *block = gpiochip_get_data(chip); | 
|  |  | 
|  | if (block->config_regs[offset] == 0) /* GPIO is not available */ | 
|  | return -ENODEV; | 
|  |  | 
|  | if (!request_region(block->runtime_reg + block->config_regs[offset], | 
|  | 1, DRV_NAME)) { | 
|  | dev_err(chip->parent, "Failed to request region 0x%04x.\n", | 
|  | block->runtime_reg + block->config_regs[offset]); | 
|  | return -EBUSY; | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void sch311x_gpio_free(struct gpio_chip *chip, unsigned offset) | 
|  | { | 
|  | struct sch311x_gpio_block *block = gpiochip_get_data(chip); | 
|  |  | 
|  | if (block->config_regs[offset] == 0) /* GPIO is not available */ | 
|  | return; | 
|  |  | 
|  | release_region(block->runtime_reg + block->config_regs[offset], 1); | 
|  | } | 
|  |  | 
|  | static int sch311x_gpio_get(struct gpio_chip *chip, unsigned offset) | 
|  | { | 
|  | struct sch311x_gpio_block *block = gpiochip_get_data(chip); | 
|  | unsigned char data; | 
|  |  | 
|  | spin_lock(&block->lock); | 
|  | data = inb(block->runtime_reg + block->data_reg); | 
|  | spin_unlock(&block->lock); | 
|  |  | 
|  | return !!(data & BIT(offset)); | 
|  | } | 
|  |  | 
|  | static void __sch311x_gpio_set(struct sch311x_gpio_block *block, | 
|  | unsigned offset, int value) | 
|  | { | 
|  | unsigned char data = inb(block->runtime_reg + block->data_reg); | 
|  | if (value) | 
|  | data |= BIT(offset); | 
|  | else | 
|  | data &= ~BIT(offset); | 
|  | outb(data, block->runtime_reg + block->data_reg); | 
|  | } | 
|  |  | 
|  | static void sch311x_gpio_set(struct gpio_chip *chip, unsigned offset, | 
|  | int value) | 
|  | { | 
|  | struct sch311x_gpio_block *block = gpiochip_get_data(chip); | 
|  |  | 
|  | spin_lock(&block->lock); | 
|  | __sch311x_gpio_set(block, offset, value); | 
|  | spin_unlock(&block->lock); | 
|  | } | 
|  |  | 
|  | static int sch311x_gpio_direction_in(struct gpio_chip *chip, unsigned offset) | 
|  | { | 
|  | struct sch311x_gpio_block *block = gpiochip_get_data(chip); | 
|  |  | 
|  | spin_lock(&block->lock); | 
|  | outb(SCH311X_GPIO_CONF_IN, block->runtime_reg + | 
|  | block->config_regs[offset]); | 
|  | spin_unlock(&block->lock); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int sch311x_gpio_direction_out(struct gpio_chip *chip, unsigned offset, | 
|  | int value) | 
|  | { | 
|  | struct sch311x_gpio_block *block = gpiochip_get_data(chip); | 
|  |  | 
|  | spin_lock(&block->lock); | 
|  |  | 
|  | outb(SCH311X_GPIO_CONF_OUT, block->runtime_reg + | 
|  | block->config_regs[offset]); | 
|  |  | 
|  | __sch311x_gpio_set(block, offset, value); | 
|  |  | 
|  | spin_unlock(&block->lock); | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int sch311x_gpio_probe(struct platform_device *pdev) | 
|  | { | 
|  | struct sch311x_pdev_data *pdata = dev_get_platdata(&pdev->dev); | 
|  | struct sch311x_gpio_priv *priv; | 
|  | struct sch311x_gpio_block *block; | 
|  | int err, i; | 
|  |  | 
|  | /* we can register all GPIO data registers at once */ | 
|  | if (!devm_request_region(&pdev->dev, pdata->runtime_reg + GP1, 6, | 
|  | DRV_NAME)) { | 
|  | dev_err(&pdev->dev, "Failed to request region 0x%04x-0x%04x.\n", | 
|  | pdata->runtime_reg + GP1, pdata->runtime_reg + GP1 + 5); | 
|  | return -EBUSY; | 
|  | } | 
|  |  | 
|  | priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); | 
|  | if (!priv) | 
|  | return -ENOMEM; | 
|  |  | 
|  | platform_set_drvdata(pdev, priv); | 
|  |  | 
|  | for (i = 0; i < ARRAY_SIZE(priv->blocks); i++) { | 
|  | block = &priv->blocks[i]; | 
|  |  | 
|  | spin_lock_init(&block->lock); | 
|  |  | 
|  | block->chip.label = DRV_NAME; | 
|  | block->chip.owner = THIS_MODULE; | 
|  | block->chip.request = sch311x_gpio_request; | 
|  | block->chip.free = sch311x_gpio_free; | 
|  | block->chip.direction_input = sch311x_gpio_direction_in; | 
|  | block->chip.direction_output = sch311x_gpio_direction_out; | 
|  | block->chip.get = sch311x_gpio_get; | 
|  | block->chip.set = sch311x_gpio_set; | 
|  | block->chip.ngpio = 8; | 
|  | block->chip.parent = &pdev->dev; | 
|  | block->chip.base = sch311x_gpio_blocks[i].base; | 
|  | block->config_regs = sch311x_gpio_blocks[i].config_regs; | 
|  | block->data_reg = sch311x_gpio_blocks[i].data_reg; | 
|  | block->runtime_reg = pdata->runtime_reg; | 
|  |  | 
|  | err = gpiochip_add_data(&block->chip, block); | 
|  | if (err < 0) { | 
|  | dev_err(&pdev->dev, | 
|  | "Could not register gpiochip, %d\n", err); | 
|  | goto exit_err; | 
|  | } | 
|  | dev_info(&pdev->dev, | 
|  | "SMSC SCH311x GPIO block %d registered.\n", i); | 
|  | } | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | exit_err: | 
|  | /* release already registered chips */ | 
|  | for (--i; i >= 0; i--) | 
|  | gpiochip_remove(&priv->blocks[i].chip); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int sch311x_gpio_remove(struct platform_device *pdev) | 
|  | { | 
|  | struct sch311x_gpio_priv *priv = platform_get_drvdata(pdev); | 
|  | int i; | 
|  |  | 
|  | for (i = 0; i < ARRAY_SIZE(priv->blocks); i++) { | 
|  | gpiochip_remove(&priv->blocks[i].chip); | 
|  | dev_info(&pdev->dev, | 
|  | "SMSC SCH311x GPIO block %d unregistered.\n", i); | 
|  | } | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static struct platform_driver sch311x_gpio_driver = { | 
|  | .driver.name	= DRV_NAME, | 
|  | .probe		= sch311x_gpio_probe, | 
|  | .remove		= sch311x_gpio_remove, | 
|  | }; | 
|  |  | 
|  |  | 
|  | /* | 
|  | *	Init & exit routines | 
|  | */ | 
|  |  | 
|  | static int __init sch311x_detect(int sio_config_port, unsigned short *addr) | 
|  | { | 
|  | int err = 0, reg; | 
|  | unsigned short base_addr; | 
|  | unsigned char dev_id; | 
|  |  | 
|  | err = sch311x_sio_enter(sio_config_port); | 
|  | if (err) | 
|  | return err; | 
|  |  | 
|  | /* Check device ID. */ | 
|  | reg = sch311x_sio_inb(sio_config_port, 0x20); | 
|  | switch (reg) { | 
|  | case 0x7c: /* SCH3112 */ | 
|  | dev_id = 2; | 
|  | break; | 
|  | case 0x7d: /* SCH3114 */ | 
|  | dev_id = 4; | 
|  | break; | 
|  | case 0x7f: /* SCH3116 */ | 
|  | dev_id = 6; | 
|  | break; | 
|  | default: | 
|  | err = -ENODEV; | 
|  | goto exit; | 
|  | } | 
|  |  | 
|  | /* Select logical device A (runtime registers) */ | 
|  | sch311x_sio_outb(sio_config_port, 0x07, 0x0a); | 
|  |  | 
|  | /* Check if Logical Device Register is currently active */ | 
|  | if ((sch311x_sio_inb(sio_config_port, 0x30) & 0x01) == 0) | 
|  | pr_info("Seems that LDN 0x0a is not active...\n"); | 
|  |  | 
|  | /* Get the base address of the runtime registers */ | 
|  | base_addr = (sch311x_sio_inb(sio_config_port, 0x60) << 8) | | 
|  | sch311x_sio_inb(sio_config_port, 0x61); | 
|  | if (!base_addr) { | 
|  | pr_err("Base address not set\n"); | 
|  | err = -ENODEV; | 
|  | goto exit; | 
|  | } | 
|  | *addr = base_addr; | 
|  |  | 
|  | pr_info("Found an SMSC SCH311%d chip at 0x%04x\n", dev_id, base_addr); | 
|  |  | 
|  | exit: | 
|  | sch311x_sio_exit(sio_config_port); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int __init sch311x_gpio_pdev_add(const unsigned short addr) | 
|  | { | 
|  | struct sch311x_pdev_data pdata; | 
|  | int err; | 
|  |  | 
|  | pdata.runtime_reg = addr; | 
|  |  | 
|  | sch311x_gpio_pdev = platform_device_alloc(DRV_NAME, -1); | 
|  | if (!sch311x_gpio_pdev) | 
|  | return -ENOMEM; | 
|  |  | 
|  | err = platform_device_add_data(sch311x_gpio_pdev, | 
|  | &pdata, sizeof(pdata)); | 
|  | if (err) { | 
|  | pr_err(DRV_NAME "Platform data allocation failed\n"); | 
|  | goto err; | 
|  | } | 
|  |  | 
|  | err = platform_device_add(sch311x_gpio_pdev); | 
|  | if (err) { | 
|  | pr_err(DRV_NAME "Device addition failed\n"); | 
|  | goto err; | 
|  | } | 
|  | return 0; | 
|  |  | 
|  | err: | 
|  | platform_device_put(sch311x_gpio_pdev); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static int __init sch311x_gpio_init(void) | 
|  | { | 
|  | int err, i; | 
|  | unsigned short addr = 0; | 
|  |  | 
|  | for (i = 0; i < ARRAY_SIZE(sch311x_ioports); i++) | 
|  | if (sch311x_detect(sch311x_ioports[i], &addr) == 0) | 
|  | break; | 
|  |  | 
|  | if (!addr) | 
|  | return -ENODEV; | 
|  |  | 
|  | err = platform_driver_register(&sch311x_gpio_driver); | 
|  | if (err) | 
|  | return err; | 
|  |  | 
|  | err = sch311x_gpio_pdev_add(addr); | 
|  | if (err) | 
|  | goto unreg_platform_driver; | 
|  |  | 
|  | return 0; | 
|  |  | 
|  | unreg_platform_driver: | 
|  | platform_driver_unregister(&sch311x_gpio_driver); | 
|  | return err; | 
|  | } | 
|  |  | 
|  | static void __exit sch311x_gpio_exit(void) | 
|  | { | 
|  | platform_device_unregister(sch311x_gpio_pdev); | 
|  | platform_driver_unregister(&sch311x_gpio_driver); | 
|  | } | 
|  |  | 
|  | module_init(sch311x_gpio_init); | 
|  | module_exit(sch311x_gpio_exit); | 
|  |  | 
|  | MODULE_AUTHOR("Bruno Randolf <br1@einfach.org>"); | 
|  | MODULE_DESCRIPTION("SMSC SCH311x GPIO Driver"); | 
|  | MODULE_LICENSE("GPL"); | 
|  | MODULE_ALIAS("platform:gpio-sch311x"); |