| /* |
| * uninorth.h: definitions for using the "UniNorth" host bridge chip |
| * from Apple. This chip is used on "Core99" machines |
| * This also includes U2 used on more recent MacRISC2/3 |
| * machines and U3 (G5) |
| * |
| */ |
| #ifdef __KERNEL__ |
| #ifndef __ASM_UNINORTH_H__ |
| #define __ASM_UNINORTH_H__ |
| |
| /* |
| * Uni-N and U3 config space reg. definitions |
| * |
| * (Little endian) |
| */ |
| |
| /* Address ranges selection. This one should work with Bandit too */ |
| /* Not U3 */ |
| #define UNI_N_ADDR_SELECT 0x48 |
| #define UNI_N_ADDR_COARSE_MASK 0xffff0000 /* 256Mb regions at *0000000 */ |
| #define UNI_N_ADDR_FINE_MASK 0x0000ffff /* 16Mb regions at f*000000 */ |
| |
| /* AGP registers */ |
| /* Not U3 */ |
| #define UNI_N_CFG_GART_BASE 0x8c |
| #define UNI_N_CFG_AGP_BASE 0x90 |
| #define UNI_N_CFG_GART_CTRL 0x94 |
| #define UNI_N_CFG_INTERNAL_STATUS 0x98 |
| #define UNI_N_CFG_GART_DUMMY_PAGE 0xa4 |
| |
| /* UNI_N_CFG_GART_CTRL bits definitions */ |
| #define UNI_N_CFG_GART_INVAL 0x00000001 |
| #define UNI_N_CFG_GART_ENABLE 0x00000100 |
| #define UNI_N_CFG_GART_2xRESET 0x00010000 |
| #define UNI_N_CFG_GART_DISSBADET 0x00020000 |
| /* The following seems to only be used only on U3 <j.glisse@gmail.com> */ |
| #define U3_N_CFG_GART_SYNCMODE 0x00040000 |
| #define U3_N_CFG_GART_PERFRD 0x00080000 |
| #define U3_N_CFG_GART_B2BGNT 0x00200000 |
| #define U3_N_CFG_GART_FASTDDR 0x00400000 |
| |
| /* My understanding of UniNorth AGP as of UniNorth rev 1.0x, |
| * revision 1.5 (x4 AGP) may need further changes. |
| * |
| * AGP_BASE register contains the base address of the AGP aperture on |
| * the AGP bus. It doesn't seem to be visible to the CPU as of UniNorth 1.x, |
| * even if decoding of this address range is enabled in the address select |
| * register. Apparently, the only supported bases are 256Mb multiples |
| * (high 4 bits of that register). |
| * |
| * GART_BASE register appear to contain the physical address of the GART |
| * in system memory in the high address bits (page aligned), and the |
| * GART size in the low order bits (number of GART pages) |
| * |
| * The GART format itself is one 32bits word per physical memory page. |
| * This word contains, in little-endian format (!!!), the physical address |
| * of the page in the high bits, and what appears to be an "enable" bit |
| * in the LSB bit (0) that must be set to 1 when the entry is valid. |
| * |
| * Obviously, the GART is not cache coherent and so any change to it |
| * must be flushed to memory (or maybe just make the GART space non |
| * cachable). AGP memory itself doesn't seem to be cache coherent neither. |
| * |
| * In order to invalidate the GART (which is probably necessary to inval |
| * the bridge internal TLBs), the following sequence has to be written, |
| * in order, to the GART_CTRL register: |
| * |
| * UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_INVAL |
| * UNI_N_CFG_GART_ENABLE |
| * UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_2xRESET |
| * UNI_N_CFG_GART_ENABLE |
| * |
| * As far as AGP "features" are concerned, it looks like fast write may |
| * not be supported but this has to be confirmed. |
| * |
| * Turning on AGP seem to require a double invalidate operation, one before |
| * setting the AGP command register, on after. |
| * |
| * Turning off AGP seems to require the following sequence: first wait |
| * for the AGP to be idle by reading the internal status register, then |
| * write in that order to the GART_CTRL register: |
| * |
| * UNI_N_CFG_GART_ENABLE | UNI_N_CFG_GART_INVAL |
| * 0 |
| * UNI_N_CFG_GART_2xRESET |
| * 0 |
| */ |
| |
| /* |
| * Uni-N memory mapped reg. definitions |
| * |
| * Those registers are Big-Endian !! |
| * |
| * Their meaning come from either Darwin and/or from experiments I made with |
| * the bootrom, I'm not sure about their exact meaning yet |
| * |
| */ |
| |
| /* Version of the UniNorth chip */ |
| #define UNI_N_VERSION 0x0000 /* Known versions: 3,7 and 8 */ |
| |
| #define UNI_N_VERSION_107 0x0003 /* 1.0.7 */ |
| #define UNI_N_VERSION_10A 0x0007 /* 1.0.10 */ |
| #define UNI_N_VERSION_150 0x0011 /* 1.5 */ |
| #define UNI_N_VERSION_200 0x0024 /* 2.0 */ |
| #define UNI_N_VERSION_PANGEA 0x00C0 /* Integrated U1 + K */ |
| #define UNI_N_VERSION_INTREPID 0x00D2 /* Integrated U2 + K */ |
| #define UNI_N_VERSION_300 0x0030 /* 3.0 (U3 on G5) */ |
| |
| /* This register is used to enable/disable various clocks */ |
| #define UNI_N_CLOCK_CNTL 0x0020 |
| #define UNI_N_CLOCK_CNTL_PCI 0x00000001 /* PCI2 clock control */ |
| #define UNI_N_CLOCK_CNTL_GMAC 0x00000002 /* GMAC clock control */ |
| #define UNI_N_CLOCK_CNTL_FW 0x00000004 /* FireWire clock control */ |
| #define UNI_N_CLOCK_CNTL_ATA100 0x00000010 /* ATA-100 clock control (U2) */ |
| |
| /* Power Management control */ |
| #define UNI_N_POWER_MGT 0x0030 |
| #define UNI_N_POWER_MGT_NORMAL 0x00 |
| #define UNI_N_POWER_MGT_IDLE2 0x01 |
| #define UNI_N_POWER_MGT_SLEEP 0x02 |
| |
| /* This register is configured by Darwin depending on the UniN |
| * revision |
| */ |
| #define UNI_N_ARB_CTRL 0x0040 |
| #define UNI_N_ARB_CTRL_QACK_DELAY_SHIFT 15 |
| #define UNI_N_ARB_CTRL_QACK_DELAY_MASK 0x0e1f8000 |
| #define UNI_N_ARB_CTRL_QACK_DELAY 0x30 |
| #define UNI_N_ARB_CTRL_QACK_DELAY105 0x00 |
| |
| /* This one _might_ return the CPU number of the CPU reading it; |
| * the bootROM decides whether to boot or to sleep/spinloop depending |
| * on this register being 0 or not |
| */ |
| #define UNI_N_CPU_NUMBER 0x0050 |
| |
| /* This register appear to be read by the bootROM to decide what |
| * to do on a non-recoverable reset (powerup or wakeup) |
| */ |
| #define UNI_N_HWINIT_STATE 0x0070 |
| #define UNI_N_HWINIT_STATE_SLEEPING 0x01 |
| #define UNI_N_HWINIT_STATE_RUNNING 0x02 |
| /* This last bit appear to be used by the bootROM to know the second |
| * CPU has started and will enter it's sleep loop with IP=0 |
| */ |
| #define UNI_N_HWINIT_STATE_CPU1_FLAG 0x10000000 |
| |
| /* This register controls AACK delay, which is set when 2004 iBook/PowerBook |
| * is in low speed mode. |
| */ |
| #define UNI_N_AACK_DELAY 0x0100 |
| #define UNI_N_AACK_DELAY_ENABLE 0x00000001 |
| |
| /* Clock status for Intrepid */ |
| #define UNI_N_CLOCK_STOP_STATUS0 0x0150 |
| #define UNI_N_CLOCK_STOPPED_EXTAGP 0x00200000 |
| #define UNI_N_CLOCK_STOPPED_AGPDEL 0x00100000 |
| #define UNI_N_CLOCK_STOPPED_I2S0_45_49 0x00080000 |
| #define UNI_N_CLOCK_STOPPED_I2S0_18 0x00040000 |
| #define UNI_N_CLOCK_STOPPED_I2S1_45_49 0x00020000 |
| #define UNI_N_CLOCK_STOPPED_I2S1_18 0x00010000 |
| #define UNI_N_CLOCK_STOPPED_TIMER 0x00008000 |
| #define UNI_N_CLOCK_STOPPED_SCC_RTCLK18 0x00004000 |
| #define UNI_N_CLOCK_STOPPED_SCC_RTCLK32 0x00002000 |
| #define UNI_N_CLOCK_STOPPED_SCC_VIA32 0x00001000 |
| #define UNI_N_CLOCK_STOPPED_SCC_SLOT0 0x00000800 |
| #define UNI_N_CLOCK_STOPPED_SCC_SLOT1 0x00000400 |
| #define UNI_N_CLOCK_STOPPED_SCC_SLOT2 0x00000200 |
| #define UNI_N_CLOCK_STOPPED_PCI_FBCLKO 0x00000100 |
| #define UNI_N_CLOCK_STOPPED_VEO0 0x00000080 |
| #define UNI_N_CLOCK_STOPPED_VEO1 0x00000040 |
| #define UNI_N_CLOCK_STOPPED_USB0 0x00000020 |
| #define UNI_N_CLOCK_STOPPED_USB1 0x00000010 |
| #define UNI_N_CLOCK_STOPPED_USB2 0x00000008 |
| #define UNI_N_CLOCK_STOPPED_32 0x00000004 |
| #define UNI_N_CLOCK_STOPPED_45 0x00000002 |
| #define UNI_N_CLOCK_STOPPED_49 0x00000001 |
| |
| #define UNI_N_CLOCK_STOP_STATUS1 0x0160 |
| #define UNI_N_CLOCK_STOPPED_PLL4REF 0x00080000 |
| #define UNI_N_CLOCK_STOPPED_CPUDEL 0x00040000 |
| #define UNI_N_CLOCK_STOPPED_CPU 0x00020000 |
| #define UNI_N_CLOCK_STOPPED_BUF_REFCKO 0x00010000 |
| #define UNI_N_CLOCK_STOPPED_PCI2 0x00008000 |
| #define UNI_N_CLOCK_STOPPED_FW 0x00004000 |
| #define UNI_N_CLOCK_STOPPED_GB 0x00002000 |
| #define UNI_N_CLOCK_STOPPED_ATA66 0x00001000 |
| #define UNI_N_CLOCK_STOPPED_ATA100 0x00000800 |
| #define UNI_N_CLOCK_STOPPED_MAX 0x00000400 |
| #define UNI_N_CLOCK_STOPPED_PCI1 0x00000200 |
| #define UNI_N_CLOCK_STOPPED_KLPCI 0x00000100 |
| #define UNI_N_CLOCK_STOPPED_USB0PCI 0x00000080 |
| #define UNI_N_CLOCK_STOPPED_USB1PCI 0x00000040 |
| #define UNI_N_CLOCK_STOPPED_USB2PCI 0x00000020 |
| #define UNI_N_CLOCK_STOPPED_7PCI1 0x00000008 |
| #define UNI_N_CLOCK_STOPPED_AGP 0x00000004 |
| #define UNI_N_CLOCK_STOPPED_PCI0 0x00000002 |
| #define UNI_N_CLOCK_STOPPED_18 0x00000001 |
| |
| /* Intrepid registe to OF do-platform-clockspreading */ |
| #define UNI_N_CLOCK_SPREADING 0x190 |
| |
| /* Uninorth 1.5 rev. has additional perf. monitor registers at 0xf00-0xf50 */ |
| |
| |
| /* |
| * U3 specific registers |
| */ |
| |
| |
| /* U3 Toggle */ |
| #define U3_TOGGLE_REG 0x00e0 |
| #define U3_PMC_START_STOP 0x0001 |
| #define U3_MPIC_RESET 0x0002 |
| #define U3_MPIC_OUTPUT_ENABLE 0x0004 |
| |
| /* U3 API PHY Config 1 */ |
| #define U3_API_PHY_CONFIG_1 0x23030 |
| |
| /* U3 HyperTransport registers */ |
| #define U3_HT_CONFIG_BASE 0x70000 |
| #define U3_HT_LINK_COMMAND 0x100 |
| #define U3_HT_LINK_CONFIG 0x110 |
| #define U3_HT_LINK_FREQ 0x120 |
| |
| #endif /* __ASM_UNINORTH_H__ */ |
| #endif /* __KERNEL__ */ |
