| /* |
| * Qualcomm Peripheral Image Loader |
| * |
| * Copyright (C) 2016 Linaro Ltd. |
| * Copyright (C) 2014 Sony Mobile Communications AB |
| * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License |
| * version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/interrupt.h> |
| #include <linux/kernel.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/module.h> |
| #include <linux/of_address.h> |
| #include <linux/of_device.h> |
| #include <linux/platform_device.h> |
| #include <linux/regmap.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/remoteproc.h> |
| #include <linux/reset.h> |
| #include <linux/soc/qcom/mdt_loader.h> |
| #include <linux/soc/qcom/smem.h> |
| #include <linux/soc/qcom/smem_state.h> |
| |
| #include "remoteproc_internal.h" |
| #include "qcom_common.h" |
| |
| #include <linux/qcom_scm.h> |
| |
| #define MPSS_CRASH_REASON_SMEM 421 |
| |
| /* RMB Status Register Values */ |
| #define RMB_PBL_SUCCESS 0x1 |
| |
| #define RMB_MBA_XPU_UNLOCKED 0x1 |
| #define RMB_MBA_XPU_UNLOCKED_SCRIBBLED 0x2 |
| #define RMB_MBA_META_DATA_AUTH_SUCCESS 0x3 |
| #define RMB_MBA_AUTH_COMPLETE 0x4 |
| |
| /* PBL/MBA interface registers */ |
| #define RMB_MBA_IMAGE_REG 0x00 |
| #define RMB_PBL_STATUS_REG 0x04 |
| #define RMB_MBA_COMMAND_REG 0x08 |
| #define RMB_MBA_STATUS_REG 0x0C |
| #define RMB_PMI_META_DATA_REG 0x10 |
| #define RMB_PMI_CODE_START_REG 0x14 |
| #define RMB_PMI_CODE_LENGTH_REG 0x18 |
| |
| #define RMB_CMD_META_DATA_READY 0x1 |
| #define RMB_CMD_LOAD_READY 0x2 |
| |
| /* QDSP6SS Register Offsets */ |
| #define QDSP6SS_RESET_REG 0x014 |
| #define QDSP6SS_GFMUX_CTL_REG 0x020 |
| #define QDSP6SS_PWR_CTL_REG 0x030 |
| |
| /* AXI Halt Register Offsets */ |
| #define AXI_HALTREQ_REG 0x0 |
| #define AXI_HALTACK_REG 0x4 |
| #define AXI_IDLE_REG 0x8 |
| |
| #define HALT_ACK_TIMEOUT_MS 100 |
| |
| /* QDSP6SS_RESET */ |
| #define Q6SS_STOP_CORE BIT(0) |
| #define Q6SS_CORE_ARES BIT(1) |
| #define Q6SS_BUS_ARES_ENABLE BIT(2) |
| |
| /* QDSP6SS_GFMUX_CTL */ |
| #define Q6SS_CLK_ENABLE BIT(1) |
| |
| /* QDSP6SS_PWR_CTL */ |
| #define Q6SS_L2DATA_SLP_NRET_N_0 BIT(0) |
| #define Q6SS_L2DATA_SLP_NRET_N_1 BIT(1) |
| #define Q6SS_L2DATA_SLP_NRET_N_2 BIT(2) |
| #define Q6SS_L2TAG_SLP_NRET_N BIT(16) |
| #define Q6SS_ETB_SLP_NRET_N BIT(17) |
| #define Q6SS_L2DATA_STBY_N BIT(18) |
| #define Q6SS_SLP_RET_N BIT(19) |
| #define Q6SS_CLAMP_IO BIT(20) |
| #define QDSS_BHS_ON BIT(21) |
| #define QDSS_LDO_BYP BIT(22) |
| |
| struct reg_info { |
| struct regulator *reg; |
| int uV; |
| int uA; |
| }; |
| |
| struct qcom_mss_reg_res { |
| const char *supply; |
| int uV; |
| int uA; |
| }; |
| |
| struct rproc_hexagon_res { |
| const char *hexagon_mba_image; |
| struct qcom_mss_reg_res *proxy_supply; |
| struct qcom_mss_reg_res *active_supply; |
| char **proxy_clk_names; |
| char **active_clk_names; |
| }; |
| |
| struct q6v5 { |
| struct device *dev; |
| struct rproc *rproc; |
| |
| void __iomem *reg_base; |
| void __iomem *rmb_base; |
| |
| struct regmap *halt_map; |
| u32 halt_q6; |
| u32 halt_modem; |
| u32 halt_nc; |
| |
| struct reset_control *mss_restart; |
| |
| struct qcom_smem_state *state; |
| unsigned stop_bit; |
| |
| struct clk *active_clks[8]; |
| struct clk *proxy_clks[4]; |
| int active_clk_count; |
| int proxy_clk_count; |
| |
| struct reg_info active_regs[1]; |
| struct reg_info proxy_regs[3]; |
| int active_reg_count; |
| int proxy_reg_count; |
| |
| struct completion start_done; |
| struct completion stop_done; |
| bool running; |
| |
| phys_addr_t mba_phys; |
| void *mba_region; |
| size_t mba_size; |
| |
| phys_addr_t mpss_phys; |
| phys_addr_t mpss_reloc; |
| void *mpss_region; |
| size_t mpss_size; |
| |
| struct qcom_rproc_subdev smd_subdev; |
| struct qcom_rproc_ssr ssr_subdev; |
| }; |
| |
| static int q6v5_regulator_init(struct device *dev, struct reg_info *regs, |
| const struct qcom_mss_reg_res *reg_res) |
| { |
| int rc; |
| int i; |
| |
| if (!reg_res) |
| return 0; |
| |
| for (i = 0; reg_res[i].supply; i++) { |
| regs[i].reg = devm_regulator_get(dev, reg_res[i].supply); |
| if (IS_ERR(regs[i].reg)) { |
| rc = PTR_ERR(regs[i].reg); |
| if (rc != -EPROBE_DEFER) |
| dev_err(dev, "Failed to get %s\n regulator", |
| reg_res[i].supply); |
| return rc; |
| } |
| |
| regs[i].uV = reg_res[i].uV; |
| regs[i].uA = reg_res[i].uA; |
| } |
| |
| return i; |
| } |
| |
| static int q6v5_regulator_enable(struct q6v5 *qproc, |
| struct reg_info *regs, int count) |
| { |
| int ret; |
| int i; |
| |
| for (i = 0; i < count; i++) { |
| if (regs[i].uV > 0) { |
| ret = regulator_set_voltage(regs[i].reg, |
| regs[i].uV, INT_MAX); |
| if (ret) { |
| dev_err(qproc->dev, |
| "Failed to request voltage for %d.\n", |
| i); |
| goto err; |
| } |
| } |
| |
| if (regs[i].uA > 0) { |
| ret = regulator_set_load(regs[i].reg, |
| regs[i].uA); |
| if (ret < 0) { |
| dev_err(qproc->dev, |
| "Failed to set regulator mode\n"); |
| goto err; |
| } |
| } |
| |
| ret = regulator_enable(regs[i].reg); |
| if (ret) { |
| dev_err(qproc->dev, "Regulator enable failed\n"); |
| goto err; |
| } |
| } |
| |
| return 0; |
| err: |
| for (; i >= 0; i--) { |
| if (regs[i].uV > 0) |
| regulator_set_voltage(regs[i].reg, 0, INT_MAX); |
| |
| if (regs[i].uA > 0) |
| regulator_set_load(regs[i].reg, 0); |
| |
| regulator_disable(regs[i].reg); |
| } |
| |
| return ret; |
| } |
| |
| static void q6v5_regulator_disable(struct q6v5 *qproc, |
| struct reg_info *regs, int count) |
| { |
| int i; |
| |
| for (i = 0; i < count; i++) { |
| if (regs[i].uV > 0) |
| regulator_set_voltage(regs[i].reg, 0, INT_MAX); |
| |
| if (regs[i].uA > 0) |
| regulator_set_load(regs[i].reg, 0); |
| |
| regulator_disable(regs[i].reg); |
| } |
| } |
| |
| static int q6v5_clk_enable(struct device *dev, |
| struct clk **clks, int count) |
| { |
| int rc; |
| int i; |
| |
| for (i = 0; i < count; i++) { |
| rc = clk_prepare_enable(clks[i]); |
| if (rc) { |
| dev_err(dev, "Clock enable failed\n"); |
| goto err; |
| } |
| } |
| |
| return 0; |
| err: |
| for (i--; i >= 0; i--) |
| clk_disable_unprepare(clks[i]); |
| |
| return rc; |
| } |
| |
| static void q6v5_clk_disable(struct device *dev, |
| struct clk **clks, int count) |
| { |
| int i; |
| |
| for (i = 0; i < count; i++) |
| clk_disable_unprepare(clks[i]); |
| } |
| |
| static struct resource_table *q6v5_find_rsc_table(struct rproc *rproc, |
| const struct firmware *fw, |
| int *tablesz) |
| { |
| static struct resource_table table = { .ver = 1, }; |
| |
| *tablesz = sizeof(table); |
| return &table; |
| } |
| |
| static int q6v5_load(struct rproc *rproc, const struct firmware *fw) |
| { |
| struct q6v5 *qproc = rproc->priv; |
| |
| memcpy(qproc->mba_region, fw->data, fw->size); |
| |
| return 0; |
| } |
| |
| static const struct rproc_fw_ops q6v5_fw_ops = { |
| .find_rsc_table = q6v5_find_rsc_table, |
| .load = q6v5_load, |
| }; |
| |
| static int q6v5_rmb_pbl_wait(struct q6v5 *qproc, int ms) |
| { |
| unsigned long timeout; |
| s32 val; |
| |
| timeout = jiffies + msecs_to_jiffies(ms); |
| for (;;) { |
| val = readl(qproc->rmb_base + RMB_PBL_STATUS_REG); |
| if (val) |
| break; |
| |
| if (time_after(jiffies, timeout)) |
| return -ETIMEDOUT; |
| |
| msleep(1); |
| } |
| |
| return val; |
| } |
| |
| static int q6v5_rmb_mba_wait(struct q6v5 *qproc, u32 status, int ms) |
| { |
| |
| unsigned long timeout; |
| s32 val; |
| |
| timeout = jiffies + msecs_to_jiffies(ms); |
| for (;;) { |
| val = readl(qproc->rmb_base + RMB_MBA_STATUS_REG); |
| if (val < 0) |
| break; |
| |
| if (!status && val) |
| break; |
| else if (status && val == status) |
| break; |
| |
| if (time_after(jiffies, timeout)) |
| return -ETIMEDOUT; |
| |
| msleep(1); |
| } |
| |
| return val; |
| } |
| |
| static int q6v5proc_reset(struct q6v5 *qproc) |
| { |
| u32 val; |
| int ret; |
| |
| /* Assert resets, stop core */ |
| val = readl(qproc->reg_base + QDSP6SS_RESET_REG); |
| val |= (Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE); |
| writel(val, qproc->reg_base + QDSP6SS_RESET_REG); |
| |
| /* Enable power block headswitch, and wait for it to stabilize */ |
| val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); |
| val |= QDSS_BHS_ON | QDSS_LDO_BYP; |
| writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); |
| udelay(1); |
| |
| /* |
| * Turn on memories. L2 banks should be done individually |
| * to minimize inrush current. |
| */ |
| val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG); |
| val |= Q6SS_SLP_RET_N | Q6SS_L2TAG_SLP_NRET_N | |
| Q6SS_ETB_SLP_NRET_N | Q6SS_L2DATA_STBY_N; |
| writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); |
| val |= Q6SS_L2DATA_SLP_NRET_N_2; |
| writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); |
| val |= Q6SS_L2DATA_SLP_NRET_N_1; |
| writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); |
| val |= Q6SS_L2DATA_SLP_NRET_N_0; |
| writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); |
| |
| /* Remove IO clamp */ |
| val &= ~Q6SS_CLAMP_IO; |
| writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG); |
| |
| /* Bring core out of reset */ |
| val = readl(qproc->reg_base + QDSP6SS_RESET_REG); |
| val &= ~Q6SS_CORE_ARES; |
| writel(val, qproc->reg_base + QDSP6SS_RESET_REG); |
| |
| /* Turn on core clock */ |
| val = readl(qproc->reg_base + QDSP6SS_GFMUX_CTL_REG); |
| val |= Q6SS_CLK_ENABLE; |
| writel(val, qproc->reg_base + QDSP6SS_GFMUX_CTL_REG); |
| |
| /* Start core execution */ |
| val = readl(qproc->reg_base + QDSP6SS_RESET_REG); |
| val &= ~Q6SS_STOP_CORE; |
| writel(val, qproc->reg_base + QDSP6SS_RESET_REG); |
| |
| /* Wait for PBL status */ |
| ret = q6v5_rmb_pbl_wait(qproc, 1000); |
| if (ret == -ETIMEDOUT) { |
| dev_err(qproc->dev, "PBL boot timed out\n"); |
| } else if (ret != RMB_PBL_SUCCESS) { |
| dev_err(qproc->dev, "PBL returned unexpected status %d\n", ret); |
| ret = -EINVAL; |
| } else { |
| ret = 0; |
| } |
| |
| return ret; |
| } |
| |
| static void q6v5proc_halt_axi_port(struct q6v5 *qproc, |
| struct regmap *halt_map, |
| u32 offset) |
| { |
| unsigned long timeout; |
| unsigned int val; |
| int ret; |
| |
| /* Check if we're already idle */ |
| ret = regmap_read(halt_map, offset + AXI_IDLE_REG, &val); |
| if (!ret && val) |
| return; |
| |
| /* Assert halt request */ |
| regmap_write(halt_map, offset + AXI_HALTREQ_REG, 1); |
| |
| /* Wait for halt */ |
| timeout = jiffies + msecs_to_jiffies(HALT_ACK_TIMEOUT_MS); |
| for (;;) { |
| ret = regmap_read(halt_map, offset + AXI_HALTACK_REG, &val); |
| if (ret || val || time_after(jiffies, timeout)) |
| break; |
| |
| msleep(1); |
| } |
| |
| ret = regmap_read(halt_map, offset + AXI_IDLE_REG, &val); |
| if (ret || !val) |
| dev_err(qproc->dev, "port failed halt\n"); |
| |
| /* Clear halt request (port will remain halted until reset) */ |
| regmap_write(halt_map, offset + AXI_HALTREQ_REG, 0); |
| } |
| |
| static int q6v5_mpss_init_image(struct q6v5 *qproc, const struct firmware *fw) |
| { |
| unsigned long dma_attrs = DMA_ATTR_FORCE_CONTIGUOUS; |
| dma_addr_t phys; |
| void *ptr; |
| int ret; |
| |
| ptr = dma_alloc_attrs(qproc->dev, fw->size, &phys, GFP_KERNEL, dma_attrs); |
| if (!ptr) { |
| dev_err(qproc->dev, "failed to allocate mdt buffer\n"); |
| return -ENOMEM; |
| } |
| |
| memcpy(ptr, fw->data, fw->size); |
| |
| writel(phys, qproc->rmb_base + RMB_PMI_META_DATA_REG); |
| writel(RMB_CMD_META_DATA_READY, qproc->rmb_base + RMB_MBA_COMMAND_REG); |
| |
| ret = q6v5_rmb_mba_wait(qproc, RMB_MBA_META_DATA_AUTH_SUCCESS, 1000); |
| if (ret == -ETIMEDOUT) |
| dev_err(qproc->dev, "MPSS header authentication timed out\n"); |
| else if (ret < 0) |
| dev_err(qproc->dev, "MPSS header authentication failed: %d\n", ret); |
| |
| dma_free_attrs(qproc->dev, fw->size, ptr, phys, dma_attrs); |
| |
| return ret < 0 ? ret : 0; |
| } |
| |
| static bool q6v5_phdr_valid(const struct elf32_phdr *phdr) |
| { |
| if (phdr->p_type != PT_LOAD) |
| return false; |
| |
| if ((phdr->p_flags & QCOM_MDT_TYPE_MASK) == QCOM_MDT_TYPE_HASH) |
| return false; |
| |
| if (!phdr->p_memsz) |
| return false; |
| |
| return true; |
| } |
| |
| static int q6v5_mpss_load(struct q6v5 *qproc) |
| { |
| const struct elf32_phdr *phdrs; |
| const struct elf32_phdr *phdr; |
| const struct firmware *seg_fw; |
| const struct firmware *fw; |
| struct elf32_hdr *ehdr; |
| phys_addr_t mpss_reloc; |
| phys_addr_t boot_addr; |
| phys_addr_t min_addr = (phys_addr_t)ULLONG_MAX; |
| phys_addr_t max_addr = 0; |
| bool relocate = false; |
| char seg_name[10]; |
| ssize_t offset; |
| size_t size; |
| void *ptr; |
| int ret; |
| int i; |
| |
| ret = request_firmware(&fw, "modem.mdt", qproc->dev); |
| if (ret < 0) { |
| dev_err(qproc->dev, "unable to load modem.mdt\n"); |
| return ret; |
| } |
| |
| /* Initialize the RMB validator */ |
| writel(0, qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG); |
| |
| ret = q6v5_mpss_init_image(qproc, fw); |
| if (ret) |
| goto release_firmware; |
| |
| ehdr = (struct elf32_hdr *)fw->data; |
| phdrs = (struct elf32_phdr *)(ehdr + 1); |
| |
| for (i = 0; i < ehdr->e_phnum; i++) { |
| phdr = &phdrs[i]; |
| |
| if (!q6v5_phdr_valid(phdr)) |
| continue; |
| |
| if (phdr->p_flags & QCOM_MDT_RELOCATABLE) |
| relocate = true; |
| |
| if (phdr->p_paddr < min_addr) |
| min_addr = phdr->p_paddr; |
| |
| if (phdr->p_paddr + phdr->p_memsz > max_addr) |
| max_addr = ALIGN(phdr->p_paddr + phdr->p_memsz, SZ_4K); |
| } |
| |
| mpss_reloc = relocate ? min_addr : qproc->mpss_phys; |
| |
| for (i = 0; i < ehdr->e_phnum; i++) { |
| phdr = &phdrs[i]; |
| |
| if (!q6v5_phdr_valid(phdr)) |
| continue; |
| |
| offset = phdr->p_paddr - mpss_reloc; |
| if (offset < 0 || offset + phdr->p_memsz > qproc->mpss_size) { |
| dev_err(qproc->dev, "segment outside memory range\n"); |
| ret = -EINVAL; |
| goto release_firmware; |
| } |
| |
| ptr = qproc->mpss_region + offset; |
| |
| if (phdr->p_filesz) { |
| snprintf(seg_name, sizeof(seg_name), "modem.b%02d", i); |
| ret = request_firmware(&seg_fw, seg_name, qproc->dev); |
| if (ret) { |
| dev_err(qproc->dev, "failed to load %s\n", seg_name); |
| goto release_firmware; |
| } |
| |
| memcpy(ptr, seg_fw->data, seg_fw->size); |
| |
| release_firmware(seg_fw); |
| } |
| |
| if (phdr->p_memsz > phdr->p_filesz) { |
| memset(ptr + phdr->p_filesz, 0, |
| phdr->p_memsz - phdr->p_filesz); |
| } |
| |
| size = readl(qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG); |
| if (!size) { |
| boot_addr = relocate ? qproc->mpss_phys : min_addr; |
| writel(boot_addr, qproc->rmb_base + RMB_PMI_CODE_START_REG); |
| writel(RMB_CMD_LOAD_READY, qproc->rmb_base + RMB_MBA_COMMAND_REG); |
| } |
| |
| size += phdr->p_memsz; |
| writel(size, qproc->rmb_base + RMB_PMI_CODE_LENGTH_REG); |
| } |
| |
| ret = q6v5_rmb_mba_wait(qproc, RMB_MBA_AUTH_COMPLETE, 10000); |
| if (ret == -ETIMEDOUT) |
| dev_err(qproc->dev, "MPSS authentication timed out\n"); |
| else if (ret < 0) |
| dev_err(qproc->dev, "MPSS authentication failed: %d\n", ret); |
| |
| release_firmware: |
| release_firmware(fw); |
| |
| return ret < 0 ? ret : 0; |
| } |
| |
| static int q6v5_start(struct rproc *rproc) |
| { |
| struct q6v5 *qproc = (struct q6v5 *)rproc->priv; |
| int ret; |
| |
| ret = q6v5_regulator_enable(qproc, qproc->proxy_regs, |
| qproc->proxy_reg_count); |
| if (ret) { |
| dev_err(qproc->dev, "failed to enable proxy supplies\n"); |
| return ret; |
| } |
| |
| ret = q6v5_clk_enable(qproc->dev, qproc->proxy_clks, |
| qproc->proxy_clk_count); |
| if (ret) { |
| dev_err(qproc->dev, "failed to enable proxy clocks\n"); |
| goto disable_proxy_reg; |
| } |
| |
| ret = q6v5_regulator_enable(qproc, qproc->active_regs, |
| qproc->active_reg_count); |
| if (ret) { |
| dev_err(qproc->dev, "failed to enable supplies\n"); |
| goto disable_proxy_clk; |
| } |
| ret = reset_control_deassert(qproc->mss_restart); |
| if (ret) { |
| dev_err(qproc->dev, "failed to deassert mss restart\n"); |
| goto disable_vdd; |
| } |
| |
| ret = q6v5_clk_enable(qproc->dev, qproc->active_clks, |
| qproc->active_clk_count); |
| if (ret) { |
| dev_err(qproc->dev, "failed to enable clocks\n"); |
| goto assert_reset; |
| } |
| |
| writel(qproc->mba_phys, qproc->rmb_base + RMB_MBA_IMAGE_REG); |
| |
| ret = q6v5proc_reset(qproc); |
| if (ret) |
| goto halt_axi_ports; |
| |
| ret = q6v5_rmb_mba_wait(qproc, 0, 5000); |
| if (ret == -ETIMEDOUT) { |
| dev_err(qproc->dev, "MBA boot timed out\n"); |
| goto halt_axi_ports; |
| } else if (ret != RMB_MBA_XPU_UNLOCKED && |
| ret != RMB_MBA_XPU_UNLOCKED_SCRIBBLED) { |
| dev_err(qproc->dev, "MBA returned unexpected status %d\n", ret); |
| ret = -EINVAL; |
| goto halt_axi_ports; |
| } |
| |
| dev_info(qproc->dev, "MBA booted, loading mpss\n"); |
| |
| ret = q6v5_mpss_load(qproc); |
| if (ret) |
| goto halt_axi_ports; |
| |
| ret = wait_for_completion_timeout(&qproc->start_done, |
| msecs_to_jiffies(5000)); |
| if (ret == 0) { |
| dev_err(qproc->dev, "start timed out\n"); |
| ret = -ETIMEDOUT; |
| goto halt_axi_ports; |
| } |
| |
| qproc->running = true; |
| |
| q6v5_clk_disable(qproc->dev, qproc->proxy_clks, |
| qproc->proxy_clk_count); |
| q6v5_regulator_disable(qproc, qproc->proxy_regs, |
| qproc->proxy_reg_count); |
| |
| return 0; |
| |
| halt_axi_ports: |
| q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_q6); |
| q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_modem); |
| q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc); |
| q6v5_clk_disable(qproc->dev, qproc->active_clks, |
| qproc->active_clk_count); |
| assert_reset: |
| reset_control_assert(qproc->mss_restart); |
| disable_vdd: |
| q6v5_regulator_disable(qproc, qproc->active_regs, |
| qproc->active_reg_count); |
| disable_proxy_clk: |
| q6v5_clk_disable(qproc->dev, qproc->proxy_clks, |
| qproc->proxy_clk_count); |
| disable_proxy_reg: |
| q6v5_regulator_disable(qproc, qproc->proxy_regs, |
| qproc->proxy_reg_count); |
| |
| return ret; |
| } |
| |
| static int q6v5_stop(struct rproc *rproc) |
| { |
| struct q6v5 *qproc = (struct q6v5 *)rproc->priv; |
| int ret; |
| |
| qproc->running = false; |
| |
| qcom_smem_state_update_bits(qproc->state, |
| BIT(qproc->stop_bit), BIT(qproc->stop_bit)); |
| |
| ret = wait_for_completion_timeout(&qproc->stop_done, |
| msecs_to_jiffies(5000)); |
| if (ret == 0) |
| dev_err(qproc->dev, "timed out on wait\n"); |
| |
| qcom_smem_state_update_bits(qproc->state, BIT(qproc->stop_bit), 0); |
| |
| q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_q6); |
| q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_modem); |
| q6v5proc_halt_axi_port(qproc, qproc->halt_map, qproc->halt_nc); |
| |
| reset_control_assert(qproc->mss_restart); |
| q6v5_clk_disable(qproc->dev, qproc->active_clks, |
| qproc->active_clk_count); |
| q6v5_regulator_disable(qproc, qproc->active_regs, |
| qproc->active_reg_count); |
| |
| return 0; |
| } |
| |
| static void *q6v5_da_to_va(struct rproc *rproc, u64 da, int len) |
| { |
| struct q6v5 *qproc = rproc->priv; |
| int offset; |
| |
| offset = da - qproc->mpss_reloc; |
| if (offset < 0 || offset + len > qproc->mpss_size) |
| return NULL; |
| |
| return qproc->mpss_region + offset; |
| } |
| |
| static const struct rproc_ops q6v5_ops = { |
| .start = q6v5_start, |
| .stop = q6v5_stop, |
| .da_to_va = q6v5_da_to_va, |
| }; |
| |
| static irqreturn_t q6v5_wdog_interrupt(int irq, void *dev) |
| { |
| struct q6v5 *qproc = dev; |
| size_t len; |
| char *msg; |
| |
| /* Sometimes the stop triggers a watchdog rather than a stop-ack */ |
| if (!qproc->running) { |
| complete(&qproc->stop_done); |
| return IRQ_HANDLED; |
| } |
| |
| msg = qcom_smem_get(QCOM_SMEM_HOST_ANY, MPSS_CRASH_REASON_SMEM, &len); |
| if (!IS_ERR(msg) && len > 0 && msg[0]) |
| dev_err(qproc->dev, "watchdog received: %s\n", msg); |
| else |
| dev_err(qproc->dev, "watchdog without message\n"); |
| |
| rproc_report_crash(qproc->rproc, RPROC_WATCHDOG); |
| |
| if (!IS_ERR(msg)) |
| msg[0] = '\0'; |
| |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t q6v5_fatal_interrupt(int irq, void *dev) |
| { |
| struct q6v5 *qproc = dev; |
| size_t len; |
| char *msg; |
| |
| msg = qcom_smem_get(QCOM_SMEM_HOST_ANY, MPSS_CRASH_REASON_SMEM, &len); |
| if (!IS_ERR(msg) && len > 0 && msg[0]) |
| dev_err(qproc->dev, "fatal error received: %s\n", msg); |
| else |
| dev_err(qproc->dev, "fatal error without message\n"); |
| |
| rproc_report_crash(qproc->rproc, RPROC_FATAL_ERROR); |
| |
| if (!IS_ERR(msg)) |
| msg[0] = '\0'; |
| |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t q6v5_handover_interrupt(int irq, void *dev) |
| { |
| struct q6v5 *qproc = dev; |
| |
| complete(&qproc->start_done); |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t q6v5_stop_ack_interrupt(int irq, void *dev) |
| { |
| struct q6v5 *qproc = dev; |
| |
| complete(&qproc->stop_done); |
| return IRQ_HANDLED; |
| } |
| |
| static int q6v5_init_mem(struct q6v5 *qproc, struct platform_device *pdev) |
| { |
| struct of_phandle_args args; |
| struct resource *res; |
| int ret; |
| |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qdsp6"); |
| qproc->reg_base = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(qproc->reg_base)) |
| return PTR_ERR(qproc->reg_base); |
| |
| res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rmb"); |
| qproc->rmb_base = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(qproc->rmb_base)) |
| return PTR_ERR(qproc->rmb_base); |
| |
| ret = of_parse_phandle_with_fixed_args(pdev->dev.of_node, |
| "qcom,halt-regs", 3, 0, &args); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "failed to parse qcom,halt-regs\n"); |
| return -EINVAL; |
| } |
| |
| qproc->halt_map = syscon_node_to_regmap(args.np); |
| of_node_put(args.np); |
| if (IS_ERR(qproc->halt_map)) |
| return PTR_ERR(qproc->halt_map); |
| |
| qproc->halt_q6 = args.args[0]; |
| qproc->halt_modem = args.args[1]; |
| qproc->halt_nc = args.args[2]; |
| |
| return 0; |
| } |
| |
| static int q6v5_init_clocks(struct device *dev, struct clk **clks, |
| char **clk_names) |
| { |
| int i; |
| |
| if (!clk_names) |
| return 0; |
| |
| for (i = 0; clk_names[i]; i++) { |
| clks[i] = devm_clk_get(dev, clk_names[i]); |
| if (IS_ERR(clks[i])) { |
| int rc = PTR_ERR(clks[i]); |
| |
| if (rc != -EPROBE_DEFER) |
| dev_err(dev, "Failed to get %s clock\n", |
| clk_names[i]); |
| return rc; |
| } |
| } |
| |
| return i; |
| } |
| |
| static int q6v5_init_reset(struct q6v5 *qproc) |
| { |
| qproc->mss_restart = devm_reset_control_get_exclusive(qproc->dev, |
| NULL); |
| if (IS_ERR(qproc->mss_restart)) { |
| dev_err(qproc->dev, "failed to acquire mss restart\n"); |
| return PTR_ERR(qproc->mss_restart); |
| } |
| |
| return 0; |
| } |
| |
| static int q6v5_request_irq(struct q6v5 *qproc, |
| struct platform_device *pdev, |
| const char *name, |
| irq_handler_t thread_fn) |
| { |
| int ret; |
| |
| ret = platform_get_irq_byname(pdev, name); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "no %s IRQ defined\n", name); |
| return ret; |
| } |
| |
| ret = devm_request_threaded_irq(&pdev->dev, ret, |
| NULL, thread_fn, |
| IRQF_TRIGGER_RISING | IRQF_ONESHOT, |
| "q6v5", qproc); |
| if (ret) |
| dev_err(&pdev->dev, "request %s IRQ failed\n", name); |
| |
| return ret; |
| } |
| |
| static int q6v5_alloc_memory_region(struct q6v5 *qproc) |
| { |
| struct device_node *child; |
| struct device_node *node; |
| struct resource r; |
| int ret; |
| |
| child = of_get_child_by_name(qproc->dev->of_node, "mba"); |
| node = of_parse_phandle(child, "memory-region", 0); |
| ret = of_address_to_resource(node, 0, &r); |
| if (ret) { |
| dev_err(qproc->dev, "unable to resolve mba region\n"); |
| return ret; |
| } |
| |
| qproc->mba_phys = r.start; |
| qproc->mba_size = resource_size(&r); |
| qproc->mba_region = devm_ioremap_wc(qproc->dev, qproc->mba_phys, qproc->mba_size); |
| if (!qproc->mba_region) { |
| dev_err(qproc->dev, "unable to map memory region: %pa+%zx\n", |
| &r.start, qproc->mba_size); |
| return -EBUSY; |
| } |
| |
| child = of_get_child_by_name(qproc->dev->of_node, "mpss"); |
| node = of_parse_phandle(child, "memory-region", 0); |
| ret = of_address_to_resource(node, 0, &r); |
| if (ret) { |
| dev_err(qproc->dev, "unable to resolve mpss region\n"); |
| return ret; |
| } |
| |
| qproc->mpss_phys = qproc->mpss_reloc = r.start; |
| qproc->mpss_size = resource_size(&r); |
| qproc->mpss_region = devm_ioremap_wc(qproc->dev, qproc->mpss_phys, qproc->mpss_size); |
| if (!qproc->mpss_region) { |
| dev_err(qproc->dev, "unable to map memory region: %pa+%zx\n", |
| &r.start, qproc->mpss_size); |
| return -EBUSY; |
| } |
| |
| return 0; |
| } |
| |
| static int q6v5_probe(struct platform_device *pdev) |
| { |
| const struct rproc_hexagon_res *desc; |
| struct q6v5 *qproc; |
| struct rproc *rproc; |
| int ret; |
| |
| desc = of_device_get_match_data(&pdev->dev); |
| if (!desc) |
| return -EINVAL; |
| |
| rproc = rproc_alloc(&pdev->dev, pdev->name, &q6v5_ops, |
| desc->hexagon_mba_image, sizeof(*qproc)); |
| if (!rproc) { |
| dev_err(&pdev->dev, "failed to allocate rproc\n"); |
| return -ENOMEM; |
| } |
| |
| rproc->fw_ops = &q6v5_fw_ops; |
| |
| qproc = (struct q6v5 *)rproc->priv; |
| qproc->dev = &pdev->dev; |
| qproc->rproc = rproc; |
| platform_set_drvdata(pdev, qproc); |
| |
| init_completion(&qproc->start_done); |
| init_completion(&qproc->stop_done); |
| |
| ret = q6v5_init_mem(qproc, pdev); |
| if (ret) |
| goto free_rproc; |
| |
| ret = q6v5_alloc_memory_region(qproc); |
| if (ret) |
| goto free_rproc; |
| |
| ret = q6v5_init_clocks(&pdev->dev, qproc->proxy_clks, |
| desc->proxy_clk_names); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "Failed to get proxy clocks.\n"); |
| goto free_rproc; |
| } |
| qproc->proxy_clk_count = ret; |
| |
| ret = q6v5_init_clocks(&pdev->dev, qproc->active_clks, |
| desc->active_clk_names); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "Failed to get active clocks.\n"); |
| goto free_rproc; |
| } |
| qproc->active_clk_count = ret; |
| |
| ret = q6v5_regulator_init(&pdev->dev, qproc->proxy_regs, |
| desc->proxy_supply); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "Failed to get proxy regulators.\n"); |
| goto free_rproc; |
| } |
| qproc->proxy_reg_count = ret; |
| |
| ret = q6v5_regulator_init(&pdev->dev, qproc->active_regs, |
| desc->active_supply); |
| if (ret < 0) { |
| dev_err(&pdev->dev, "Failed to get active regulators.\n"); |
| goto free_rproc; |
| } |
| qproc->active_reg_count = ret; |
| |
| ret = q6v5_init_reset(qproc); |
| if (ret) |
| goto free_rproc; |
| |
| ret = q6v5_request_irq(qproc, pdev, "wdog", q6v5_wdog_interrupt); |
| if (ret < 0) |
| goto free_rproc; |
| |
| ret = q6v5_request_irq(qproc, pdev, "fatal", q6v5_fatal_interrupt); |
| if (ret < 0) |
| goto free_rproc; |
| |
| ret = q6v5_request_irq(qproc, pdev, "handover", q6v5_handover_interrupt); |
| if (ret < 0) |
| goto free_rproc; |
| |
| ret = q6v5_request_irq(qproc, pdev, "stop-ack", q6v5_stop_ack_interrupt); |
| if (ret < 0) |
| goto free_rproc; |
| |
| qproc->state = qcom_smem_state_get(&pdev->dev, "stop", &qproc->stop_bit); |
| if (IS_ERR(qproc->state)) { |
| ret = PTR_ERR(qproc->state); |
| goto free_rproc; |
| } |
| |
| qcom_add_smd_subdev(rproc, &qproc->smd_subdev); |
| qcom_add_ssr_subdev(rproc, &qproc->ssr_subdev, "mpss"); |
| |
| ret = rproc_add(rproc); |
| if (ret) |
| goto free_rproc; |
| |
| return 0; |
| |
| free_rproc: |
| rproc_free(rproc); |
| |
| return ret; |
| } |
| |
| static int q6v5_remove(struct platform_device *pdev) |
| { |
| struct q6v5 *qproc = platform_get_drvdata(pdev); |
| |
| rproc_del(qproc->rproc); |
| |
| qcom_remove_smd_subdev(qproc->rproc, &qproc->smd_subdev); |
| qcom_remove_ssr_subdev(qproc->rproc, &qproc->ssr_subdev); |
| rproc_free(qproc->rproc); |
| |
| return 0; |
| } |
| |
| static const struct rproc_hexagon_res msm8916_mss = { |
| .hexagon_mba_image = "mba.mbn", |
| .proxy_supply = (struct qcom_mss_reg_res[]) { |
| { |
| .supply = "mx", |
| .uV = 1050000, |
| }, |
| { |
| .supply = "cx", |
| .uA = 100000, |
| }, |
| { |
| .supply = "pll", |
| .uA = 100000, |
| }, |
| {} |
| }, |
| .proxy_clk_names = (char*[]){ |
| "xo", |
| NULL |
| }, |
| .active_clk_names = (char*[]){ |
| "iface", |
| "bus", |
| "mem", |
| NULL |
| }, |
| }; |
| |
| static const struct rproc_hexagon_res msm8974_mss = { |
| .hexagon_mba_image = "mba.b00", |
| .proxy_supply = (struct qcom_mss_reg_res[]) { |
| { |
| .supply = "mx", |
| .uV = 1050000, |
| }, |
| { |
| .supply = "cx", |
| .uA = 100000, |
| }, |
| { |
| .supply = "pll", |
| .uA = 100000, |
| }, |
| {} |
| }, |
| .active_supply = (struct qcom_mss_reg_res[]) { |
| { |
| .supply = "mss", |
| .uV = 1050000, |
| .uA = 100000, |
| }, |
| {} |
| }, |
| .proxy_clk_names = (char*[]){ |
| "xo", |
| NULL |
| }, |
| .active_clk_names = (char*[]){ |
| "iface", |
| "bus", |
| "mem", |
| NULL |
| }, |
| }; |
| |
| static const struct of_device_id q6v5_of_match[] = { |
| { .compatible = "qcom,q6v5-pil", .data = &msm8916_mss}, |
| { .compatible = "qcom,msm8916-mss-pil", .data = &msm8916_mss}, |
| { .compatible = "qcom,msm8974-mss-pil", .data = &msm8974_mss}, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, q6v5_of_match); |
| |
| static struct platform_driver q6v5_driver = { |
| .probe = q6v5_probe, |
| .remove = q6v5_remove, |
| .driver = { |
| .name = "qcom-q6v5-pil", |
| .of_match_table = q6v5_of_match, |
| }, |
| }; |
| module_platform_driver(q6v5_driver); |
| |
| MODULE_DESCRIPTION("Peripheral Image Loader for Hexagon"); |
| MODULE_LICENSE("GPL v2"); |