| # |
| # I2C Sensor device configuration |
| # |
| |
| menu "Hardware Sensors Chip support" |
| depends on I2C |
| |
| config I2C_SENSOR |
| tristate |
| default n |
| |
| config SENSORS_ADM1021 |
| tristate "Analog Devices ADM1021 and compatibles" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Analog Devices ADM1021 |
| and ADM1023 sensor chips and clones: Maxim MAX1617 and MAX1617A, |
| Genesys Logic GL523SM, National Semiconductor LM84, TI THMC10, |
| and the XEON processor built-in sensor. |
| |
| This driver can also be built as a module. If so, the module |
| will be called adm1021. |
| |
| config SENSORS_ADM1025 |
| tristate "Analog Devices ADM1025 and compatibles" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Analog Devices ADM1025 |
| and Philips NE1619 sensor chips. |
| This driver can also be built as a module. If so, the module |
| will be called adm1025. |
| |
| config SENSORS_ADM1026 |
| tristate "Analog Devices ADM1026 and compatibles" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Analog Devices ADM1026 |
| This driver can also be built as a module. If so, the module |
| will be called adm1026. |
| |
| config SENSORS_ADM1031 |
| tristate "Analog Devices ADM1031 and compatibles" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Analog Devices ADM1031 |
| and ADM1030 sensor chips. |
| This driver can also be built as a module. If so, the module |
| will be called adm1031. |
| |
| config SENSORS_ADM9240 |
| tristate "Analog Devices ADM9240 and compatibles" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Analog Devices ADM9240, |
| Dallas DS1780, National Semiconductor LM81 sensor chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called adm9240. |
| |
| config SENSORS_ASB100 |
| tristate "Asus ASB100 Bach" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for the ASB100 Bach sensor |
| chip found on some Asus mainboards. |
| |
| This driver can also be built as a module. If so, the module |
| will be called asb100. |
| |
| config SENSORS_ATXP1 |
| tristate "Attansic ATXP1 VID controller" |
| depends on I2C && EXPERIMENTAL |
| help |
| If you say yes here you get support for the Attansic ATXP1 VID |
| controller. |
| |
| If your board have such a chip, you are able to control your CPU |
| core and other voltages. |
| |
| This driver can also be built as a module. If so, the module |
| will be called atxp1. |
| |
| config SENSORS_DS1621 |
| tristate "Dallas Semiconductor DS1621 and DS1625" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Dallas Semiconductor |
| DS1621 and DS1625 sensor chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called ds1621. |
| |
| config SENSORS_FSCHER |
| tristate "FSC Hermes" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Fujitsu Siemens |
| Computers Hermes sensor chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called fscher. |
| |
| config SENSORS_FSCPOS |
| tristate "FSC Poseidon" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Fujitsu Siemens |
| Computers Poseidon sensor chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called fscpos. |
| |
| config SENSORS_GL518SM |
| tristate "Genesys Logic GL518SM" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Genesys Logic GL518SM |
| sensor chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called gl518sm. |
| |
| config SENSORS_GL520SM |
| tristate "Genesys Logic GL520SM" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Genesys Logic GL520SM |
| sensor chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called gl520sm. |
| |
| config SENSORS_IT87 |
| tristate "ITE IT87xx and compatibles" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for ITE IT87xx sensor chips |
| and clones: SiS960. |
| |
| This driver can also be built as a module. If so, the module |
| will be called it87. |
| |
| config SENSORS_LM63 |
| tristate "National Semiconductor LM63" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for the National Semiconductor |
| LM63 remote diode digital temperature sensor with integrated fan |
| control. Such chips are found on the Tyan S4882 (Thunder K8QS Pro) |
| motherboard, among others. |
| |
| This driver can also be built as a module. If so, the module |
| will be called lm63. |
| |
| config SENSORS_LM75 |
| tristate "National Semiconductor LM75 and compatibles" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for National Semiconductor LM75 |
| sensor chips and clones: Dallas Semiconductor DS75 and DS1775 (in |
| 9-bit precision mode), and TelCom (now Microchip) TCN75. |
| |
| The DS75 and DS1775 in 10- to 12-bit precision modes will require |
| a force module parameter. The driver will not handle the extra |
| precision anyhow. |
| |
| This driver can also be built as a module. If so, the module |
| will be called lm75. |
| |
| config SENSORS_LM77 |
| tristate "National Semiconductor LM77" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for National Semiconductor LM77 |
| sensor chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called lm77. |
| |
| config SENSORS_LM78 |
| tristate "National Semiconductor LM78 and compatibles" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for National Semiconductor LM78, |
| LM78-J and LM79. This can also be built as a module which can be |
| inserted and removed while the kernel is running. |
| |
| This driver can also be built as a module. If so, the module |
| will be called lm78. |
| |
| config SENSORS_LM80 |
| tristate "National Semiconductor LM80" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for National Semiconductor |
| LM80 sensor chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called lm80. |
| |
| config SENSORS_LM83 |
| tristate "National Semiconductor LM83" |
| depends on I2C |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for National Semiconductor |
| LM83 sensor chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called lm83. |
| |
| config SENSORS_LM85 |
| tristate "National Semiconductor LM85 and compatibles" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for National Semiconductor LM85 |
| sensor chips and clones: ADT7463 and ADM1027. |
| |
| This driver can also be built as a module. If so, the module |
| will be called lm85. |
| |
| config SENSORS_LM87 |
| tristate "National Semiconductor LM87" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for National Semiconductor LM87 |
| sensor chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called lm87. |
| |
| config SENSORS_LM90 |
| tristate "National Semiconductor LM90 and compatibles" |
| depends on I2C |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for National Semiconductor LM90, |
| LM86, LM89 and LM99, Analog Devices ADM1032 and Maxim MAX6657 and |
| MAX6658 sensor chips. |
| |
| The Analog Devices ADT7461 sensor chip is also supported, but only |
| if found in ADM1032 compatibility mode. |
| |
| This driver can also be built as a module. If so, the module |
| will be called lm90. |
| |
| config SENSORS_LM92 |
| tristate "National Semiconductor LM92 and compatibles" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for National Semiconductor LM92 |
| and Maxim MAX6635 sensor chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called lm92. |
| |
| config SENSORS_MAX1619 |
| tristate "Maxim MAX1619 sensor chip" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for MAX1619 sensor chip. |
| |
| This driver can also be built as a module. If so, the module |
| will be called max1619. |
| |
| config SENSORS_PC87360 |
| tristate "National Semiconductor PC87360 family" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| select I2C_ISA |
| help |
| If you say yes here you get access to the hardware monitoring |
| functions of the National Semiconductor PC8736x Super-I/O chips. |
| The PC87360, PC87363 and PC87364 only have fan monitoring and |
| control. The PC87365 and PC87366 additionally have voltage and |
| temperature monitoring. |
| |
| This driver can also be built as a module. If so, the module |
| will be called pc87360. |
| |
| config SENSORS_SMSC47B397 |
| tristate "SMSC LPC47B397-NC" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| select I2C_ISA |
| help |
| If you say yes here you get support for the SMSC LPC47B397-NC |
| sensor chip. |
| |
| This driver can also be built as a module. If so, the module |
| will be called smsc47b397. |
| |
| config SENSORS_SIS5595 |
| tristate "Silicon Integrated Systems Corp. SiS5595" |
| depends on I2C && PCI && EXPERIMENTAL |
| select I2C_SENSOR |
| select I2C_ISA |
| help |
| If you say yes here you get support for the integrated sensors in |
| SiS5595 South Bridges. |
| |
| This driver can also be built as a module. If so, the module |
| will be called sis5595. |
| |
| config SENSORS_SMSC47M1 |
| tristate "SMSC LPC47M10x and compatibles" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| select I2C_ISA |
| help |
| If you say yes here you get support for the integrated fan |
| monitoring and control capabilities of the SMSC LPC47B27x, |
| LPC47M10x, LPC47M13x, LPC47M14x, LPC47M15x and LPC47M192 chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called smsc47m1. |
| |
| config SENSORS_VIA686A |
| tristate "VIA686A" |
| depends on I2C && PCI && EXPERIMENTAL |
| select I2C_SENSOR |
| select I2C_ISA |
| help |
| If you say yes here you get support for the integrated sensors in |
| Via 686A/B South Bridges. |
| |
| This driver can also be built as a module. If so, the module |
| will be called via686a. |
| |
| config SENSORS_W83781D |
| tristate "Winbond W83781D, W83782D, W83783S, W83627HF, Asus AS99127F" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for the Winbond W8378x series |
| of sensor chips: the W83781D, W83782D, W83783S and W83627HF, |
| and the similar Asus AS99127F. |
| |
| This driver can also be built as a module. If so, the module |
| will be called w83781d. |
| |
| config SENSORS_W83L785TS |
| tristate "Winbond W83L785TS-S" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for the Winbond W83L785TS-S |
| sensor chip, which is used on the Asus A7N8X, among other |
| motherboards. |
| |
| This driver can also be built as a module. If so, the module |
| will be called w83l785ts. |
| |
| config SENSORS_W83627HF |
| tristate "Winbond W83627HF, W83627THF, W83637HF, W83697HF" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| select I2C_ISA |
| help |
| If you say yes here you get support for the Winbond W836X7 series |
| of sensor chips: the W83627HF, W83627THF, W83637HF, and the W83697HF |
| |
| This driver can also be built as a module. If so, the module |
| will be called w83627hf. |
| |
| config SENSORS_W83627EHF |
| tristate "Winbond W83627EHF" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| select I2C_ISA |
| help |
| If you say yes here you get preliminary support for the hardware |
| monitoring functionality of the Winbond W83627EHF Super-I/O chip. |
| Only fan and temperature inputs are supported at the moment, while |
| the chip does much more than that. |
| |
| This driver can also be built as a module. If so, the module |
| will be called w83627ehf. |
| |
| endmenu |
| |
| menu "Other I2C Chip support" |
| depends on I2C |
| |
| config SENSORS_DS1337 |
| tristate "Dallas Semiconductor DS1337 and DS1339 Real Time Clock" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Dallas Semiconductor |
| DS1337 and DS1339 real-time clock chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called ds1337. |
| |
| config SENSORS_EEPROM |
| tristate "EEPROM reader" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get read-only access to the EEPROM data |
| available on modern memory DIMMs and Sony Vaio laptops. Such |
| EEPROMs could theoretically be available on other devices as well. |
| |
| This driver can also be built as a module. If so, the module |
| will be called eeprom. |
| |
| config SENSORS_PCF8574 |
| tristate "Philips PCF8574 and PCF8574A" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Philips PCF8574 and |
| PCF8574A chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called pcf8574. |
| |
| config SENSORS_PCF8591 |
| tristate "Philips PCF8591" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for Philips PCF8591 chips. |
| |
| This driver can also be built as a module. If so, the module |
| will be called pcf8591. |
| |
| config SENSORS_RTC8564 |
| tristate "Epson 8564 RTC chip" |
| depends on I2C && EXPERIMENTAL |
| select I2C_SENSOR |
| help |
| If you say yes here you get support for the Epson 8564 RTC chip. |
| |
| This driver can also be built as a module. If so, the module |
| will be called i2c-rtc8564. |
| |
| config ISP1301_OMAP |
| tristate "Philips ISP1301 with OMAP OTG" |
| depends on I2C && ARCH_OMAP_OTG |
| help |
| If you say yes here you get support for the Philips ISP1301 |
| USB-On-The-Go transceiver working with the OMAP OTG controller. |
| The ISP1301 is used in products including H2 and H3 development |
| boards for Texas Instruments OMAP processors. |
| |
| This driver can also be built as a module. If so, the module |
| will be called isp1301_omap. |
| |
| config SENSORS_M41T00 |
| tristate "ST M41T00 RTC chip" |
| depends on I2C && PPC32 |
| help |
| If you say yes here you get support for the ST M41T00 RTC chip. |
| |
| This driver can also be built as a module. If so, the module |
| will be called m41t00. |
| |
| endmenu |
