Documentation/devicetree/bindings/display/amlogic,meson-dw-hdmi.txt

Amlogic specific extensions to the Synopsys Designware HDMI Controller
======================================================================

The Amlogic Meson Synopsys Designware Integration is composed of :
- A Synopsys DesignWare HDMI Controller IP
- A TOP control block controlling the Clocks and PHY
- A custom HDMI PHY in order to convert video to TMDS signal
 ___________________________________
|            HDMI TOP               |<= HPD
|___________________________________|
|                  |                |
|  Synopsys HDMI   |   HDMI PHY     |=> TMDS
|    Controller    |________________|
|___________________________________|<=> DDC

The HDMI TOP block only supports HPD sensing.
The Synopsys HDMI Controller interrupt is routed through the
TOP Block interrupt.
Communication to the TOP Block and the Synopsys HDMI Controller is done
via a pair of dedicated addr+read/write registers.
The HDMI PHY is configured by registers in the HHI register block.

Pixel data arrives in 4:4:4 format from the VENC block and the VPU HDMI mux
selects either the ENCI encoder for the 576i or 480i formats or the ENCP
encoder for all the other formats including interlaced HD formats.

The VENC uses a DVI encoder on top of the ENCI or ENCP encoders to generate
DVI timings for the HDMI controller.

Amlogic Meson GXBB, GXL and GXM SoCs families embeds the Synopsys DesignWare
HDMI TX IP version 2.01a with HDCP and I2C & S/PDIF
audio source interfaces.

Required properties:
- compatible: value should be different for each SoC family as :
	- GXBB (S905) : "amlogic,meson-gxbb-dw-hdmi"
	- GXL (S905X, S905D) : "amlogic,meson-gxl-dw-hdmi"
	- GXM (S912) : "amlogic,meson-gxm-dw-hdmi"
	followed by the common "amlogic,meson-gx-dw-hdmi"
- reg: Physical base address and length of the controller's registers.
- interrupts: The HDMI interrupt number
- clocks, clock-names : must have the phandles to the HDMI iahb and isfr clocks,
  and the Amlogic Meson venci clocks as described in
  Documentation/devicetree/bindings/clock/clock-bindings.txt,
  the clocks are soc specific, the clock-names should be "iahb", "isfr", "venci"
- resets, resets-names: must have the phandles to the HDMI apb, glue and phy
  resets as described in :
  Documentation/devicetree/bindings/reset/reset.txt,
  the reset-names should be "hdmitx_apb", "hdmitx", "hdmitx_phy"

Required nodes:

The connections to the HDMI ports are modeled using the OF graph
bindings specified in Documentation/devicetree/bindings/graph.txt.

The following table lists for each supported model the port number
corresponding to each HDMI output and input.

		Port 0		Port 1
-----------------------------------------
 S905 (GXBB)	VENC Input	TMDS Output
 S905X (GXL)	VENC Input	TMDS Output
 S905D (GXL)	VENC Input	TMDS Output
 S912 (GXM)	VENC Input	TMDS Output

Example:

hdmi-connector {
	compatible = "hdmi-connector";
	type = "a";

	port {
		hdmi_connector_in: endpoint {
			remote-endpoint = <&hdmi_tx_tmds_out>;
		};
	};
};

hdmi_tx: hdmi-tx@c883a000 {
	compatible = "amlogic,meson-gxbb-dw-hdmi", "amlogic,meson-gx-dw-hdmi";
	reg = <0x0 0xc883a000 0x0 0x1c>;
	interrupts = <GIC_SPI 57 IRQ_TYPE_EDGE_RISING>;
	resets = <&reset RESET_HDMITX_CAPB3>,
		 <&reset RESET_HDMI_SYSTEM_RESET>,
		 <&reset RESET_HDMI_TX>;
	reset-names = "hdmitx_apb", "hdmitx", "hdmitx_phy";
	clocks = <&clkc CLKID_HDMI_PCLK>,
		 <&clkc CLKID_CLK81>,
		 <&clkc CLKID_GCLK_VENCI_INT0>;
	clock-names = "isfr", "iahb", "venci";
	#address-cells = <1>;
	#size-cells = <0>;

	/* VPU VENC Input */
	hdmi_tx_venc_port: port@0 {
		reg = <0>;

		hdmi_tx_in: endpoint {
			remote-endpoint = <&hdmi_tx_out>;
		};
	};

	/* TMDS Output */
	hdmi_tx_tmds_port: port@1 {
		reg = <1>;

		hdmi_tx_tmds_out: endpoint {
			remote-endpoint = <&hdmi_connector_in>;
		};
	};
};