| /* |
| * I2C Link Layer for ST NCI NFC controller familly based Driver |
| * Copyright (C) 2014-2015 STMicroelectronics SAS. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms and conditions of the GNU General Public License, |
| * version 2, as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, see <http://www.gnu.org/licenses/>. |
| */ |
| |
| #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt |
| |
| #include <linux/module.h> |
| #include <linux/i2c.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/acpi.h> |
| #include <linux/interrupt.h> |
| #include <linux/delay.h> |
| #include <linux/nfc.h> |
| #include <linux/of.h> |
| |
| #include "st-nci.h" |
| |
| #define DRIVER_DESC "NCI NFC driver for ST_NCI" |
| |
| /* ndlc header */ |
| #define ST_NCI_FRAME_HEADROOM 1 |
| #define ST_NCI_FRAME_TAILROOM 0 |
| |
| #define ST_NCI_I2C_MIN_SIZE 4 /* PCB(1) + NCI Packet header(3) */ |
| #define ST_NCI_I2C_MAX_SIZE 250 /* req 4.2.1 */ |
| |
| #define ST_NCI_DRIVER_NAME "st_nci" |
| #define ST_NCI_I2C_DRIVER_NAME "st_nci_i2c" |
| |
| struct st_nci_i2c_phy { |
| struct i2c_client *i2c_dev; |
| struct llt_ndlc *ndlc; |
| |
| bool irq_active; |
| |
| struct gpio_desc *gpiod_reset; |
| |
| struct st_nci_se_status se_status; |
| }; |
| |
| static int st_nci_i2c_enable(void *phy_id) |
| { |
| struct st_nci_i2c_phy *phy = phy_id; |
| |
| gpiod_set_value(phy->gpiod_reset, 0); |
| usleep_range(10000, 15000); |
| gpiod_set_value(phy->gpiod_reset, 1); |
| usleep_range(80000, 85000); |
| |
| if (phy->ndlc->powered == 0 && phy->irq_active == 0) { |
| enable_irq(phy->i2c_dev->irq); |
| phy->irq_active = true; |
| } |
| |
| return 0; |
| } |
| |
| static void st_nci_i2c_disable(void *phy_id) |
| { |
| struct st_nci_i2c_phy *phy = phy_id; |
| |
| disable_irq_nosync(phy->i2c_dev->irq); |
| phy->irq_active = false; |
| } |
| |
| /* |
| * Writing a frame must not return the number of written bytes. |
| * It must return either zero for success, or <0 for error. |
| * In addition, it must not alter the skb |
| */ |
| static int st_nci_i2c_write(void *phy_id, struct sk_buff *skb) |
| { |
| int r = -1; |
| struct st_nci_i2c_phy *phy = phy_id; |
| struct i2c_client *client = phy->i2c_dev; |
| |
| if (phy->ndlc->hard_fault != 0) |
| return phy->ndlc->hard_fault; |
| |
| r = i2c_master_send(client, skb->data, skb->len); |
| if (r < 0) { /* Retry, chip was in standby */ |
| usleep_range(1000, 4000); |
| r = i2c_master_send(client, skb->data, skb->len); |
| } |
| |
| if (r >= 0) { |
| if (r != skb->len) |
| r = -EREMOTEIO; |
| else |
| r = 0; |
| } |
| |
| return r; |
| } |
| |
| /* |
| * Reads an ndlc frame and returns it in a newly allocated sk_buff. |
| * returns: |
| * 0 : if received frame is complete |
| * -EREMOTEIO : i2c read error (fatal) |
| * -EBADMSG : frame was incorrect and discarded |
| * -ENOMEM : cannot allocate skb, frame dropped |
| */ |
| static int st_nci_i2c_read(struct st_nci_i2c_phy *phy, |
| struct sk_buff **skb) |
| { |
| int r; |
| u8 len; |
| u8 buf[ST_NCI_I2C_MAX_SIZE]; |
| struct i2c_client *client = phy->i2c_dev; |
| |
| r = i2c_master_recv(client, buf, ST_NCI_I2C_MIN_SIZE); |
| if (r < 0) { /* Retry, chip was in standby */ |
| usleep_range(1000, 4000); |
| r = i2c_master_recv(client, buf, ST_NCI_I2C_MIN_SIZE); |
| } |
| |
| if (r != ST_NCI_I2C_MIN_SIZE) |
| return -EREMOTEIO; |
| |
| len = be16_to_cpu(*(__be16 *) (buf + 2)); |
| if (len > ST_NCI_I2C_MAX_SIZE) { |
| nfc_err(&client->dev, "invalid frame len\n"); |
| return -EBADMSG; |
| } |
| |
| *skb = alloc_skb(ST_NCI_I2C_MIN_SIZE + len, GFP_KERNEL); |
| if (*skb == NULL) |
| return -ENOMEM; |
| |
| skb_reserve(*skb, ST_NCI_I2C_MIN_SIZE); |
| skb_put(*skb, ST_NCI_I2C_MIN_SIZE); |
| memcpy((*skb)->data, buf, ST_NCI_I2C_MIN_SIZE); |
| |
| if (!len) |
| return 0; |
| |
| r = i2c_master_recv(client, buf, len); |
| if (r != len) { |
| kfree_skb(*skb); |
| return -EREMOTEIO; |
| } |
| |
| skb_put(*skb, len); |
| memcpy((*skb)->data + ST_NCI_I2C_MIN_SIZE, buf, len); |
| |
| return 0; |
| } |
| |
| /* |
| * Reads an ndlc frame from the chip. |
| * |
| * On ST_NCI, IRQ goes in idle state when read starts. |
| */ |
| static irqreturn_t st_nci_irq_thread_fn(int irq, void *phy_id) |
| { |
| struct st_nci_i2c_phy *phy = phy_id; |
| struct i2c_client *client; |
| struct sk_buff *skb = NULL; |
| int r; |
| |
| if (!phy || !phy->ndlc || irq != phy->i2c_dev->irq) { |
| WARN_ON_ONCE(1); |
| return IRQ_NONE; |
| } |
| |
| client = phy->i2c_dev; |
| dev_dbg(&client->dev, "IRQ\n"); |
| |
| if (phy->ndlc->hard_fault) |
| return IRQ_HANDLED; |
| |
| if (!phy->ndlc->powered) { |
| st_nci_i2c_disable(phy); |
| return IRQ_HANDLED; |
| } |
| |
| r = st_nci_i2c_read(phy, &skb); |
| if (r == -EREMOTEIO || r == -ENOMEM || r == -EBADMSG) |
| return IRQ_HANDLED; |
| |
| ndlc_recv(phy->ndlc, skb); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static struct nfc_phy_ops i2c_phy_ops = { |
| .write = st_nci_i2c_write, |
| .enable = st_nci_i2c_enable, |
| .disable = st_nci_i2c_disable, |
| }; |
| |
| static const struct acpi_gpio_params reset_gpios = { 1, 0, false }; |
| |
| static const struct acpi_gpio_mapping acpi_st_nci_gpios[] = { |
| { "reset-gpios", &reset_gpios, 1 }, |
| {}, |
| }; |
| |
| static int st_nci_i2c_probe(struct i2c_client *client, |
| const struct i2c_device_id *id) |
| { |
| struct device *dev = &client->dev; |
| struct st_nci_i2c_phy *phy; |
| int r; |
| |
| dev_dbg(&client->dev, "%s\n", __func__); |
| dev_dbg(&client->dev, "IRQ: %d\n", client->irq); |
| |
| if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) { |
| nfc_err(&client->dev, "Need I2C_FUNC_I2C\n"); |
| return -ENODEV; |
| } |
| |
| phy = devm_kzalloc(dev, sizeof(struct st_nci_i2c_phy), GFP_KERNEL); |
| if (!phy) |
| return -ENOMEM; |
| |
| phy->i2c_dev = client; |
| |
| i2c_set_clientdata(client, phy); |
| |
| r = devm_acpi_dev_add_driver_gpios(dev, acpi_st_nci_gpios); |
| if (r) |
| dev_dbg(dev, "Unable to add GPIO mapping table\n"); |
| |
| /* Get RESET GPIO */ |
| phy->gpiod_reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); |
| if (IS_ERR(phy->gpiod_reset)) { |
| nfc_err(dev, "Unable to get RESET GPIO\n"); |
| return -ENODEV; |
| } |
| |
| phy->se_status.is_ese_present = |
| device_property_read_bool(dev, "ese-present"); |
| phy->se_status.is_uicc_present = |
| device_property_read_bool(dev, "uicc-present"); |
| |
| r = ndlc_probe(phy, &i2c_phy_ops, &client->dev, |
| ST_NCI_FRAME_HEADROOM, ST_NCI_FRAME_TAILROOM, |
| &phy->ndlc, &phy->se_status); |
| if (r < 0) { |
| nfc_err(&client->dev, "Unable to register ndlc layer\n"); |
| return r; |
| } |
| |
| phy->irq_active = true; |
| r = devm_request_threaded_irq(&client->dev, client->irq, NULL, |
| st_nci_irq_thread_fn, |
| IRQF_ONESHOT, |
| ST_NCI_DRIVER_NAME, phy); |
| if (r < 0) |
| nfc_err(&client->dev, "Unable to register IRQ handler\n"); |
| |
| return r; |
| } |
| |
| static int st_nci_i2c_remove(struct i2c_client *client) |
| { |
| struct st_nci_i2c_phy *phy = i2c_get_clientdata(client); |
| |
| dev_dbg(&client->dev, "%s\n", __func__); |
| |
| ndlc_remove(phy->ndlc); |
| |
| return 0; |
| } |
| |
| static struct i2c_device_id st_nci_i2c_id_table[] = { |
| {ST_NCI_DRIVER_NAME, 0}, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(i2c, st_nci_i2c_id_table); |
| |
| static const struct acpi_device_id st_nci_i2c_acpi_match[] = { |
| {"SMO2101"}, |
| {"SMO2102"}, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(acpi, st_nci_i2c_acpi_match); |
| |
| static const struct of_device_id of_st_nci_i2c_match[] = { |
| { .compatible = "st,st21nfcb-i2c", }, |
| { .compatible = "st,st21nfcb_i2c", }, |
| { .compatible = "st,st21nfcc-i2c", }, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(of, of_st_nci_i2c_match); |
| |
| static struct i2c_driver st_nci_i2c_driver = { |
| .driver = { |
| .name = ST_NCI_I2C_DRIVER_NAME, |
| .of_match_table = of_match_ptr(of_st_nci_i2c_match), |
| .acpi_match_table = ACPI_PTR(st_nci_i2c_acpi_match), |
| }, |
| .probe = st_nci_i2c_probe, |
| .id_table = st_nci_i2c_id_table, |
| .remove = st_nci_i2c_remove, |
| }; |
| module_i2c_driver(st_nci_i2c_driver); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_DESCRIPTION(DRIVER_DESC); |