| /* gdb-stub.c: FRV GDB stub | |
| * | |
| * Copyright (C) 2003,4 Red Hat, Inc. All Rights Reserved. | |
| * Written by David Howells (dhowells@redhat.com) | |
| * - Derived from Linux/MIPS version, Copyright (C) 1995 Andreas Busse | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License | |
| * as published by the Free Software Foundation; either version | |
| * 2 of the License, or (at your option) any later version. | |
| */ | |
| /* | |
| * To enable debugger support, two things need to happen. One, a | |
| * call to set_debug_traps() is necessary in order to allow any breakpoints | |
| * or error conditions to be properly intercepted and reported to gdb. | |
| * Two, a breakpoint needs to be generated to begin communication. This | |
| * is most easily accomplished by a call to breakpoint(). Breakpoint() | |
| * simulates a breakpoint by executing a BREAK instruction. | |
| * | |
| * | |
| * The following gdb commands are supported: | |
| * | |
| * command function Return value | |
| * | |
| * g return the value of the CPU registers hex data or ENN | |
| * G set the value of the CPU registers OK or ENN | |
| * | |
| * mAA..AA,LLLL Read LLLL bytes at address AA..AA hex data or ENN | |
| * MAA..AA,LLLL: Write LLLL bytes at address AA.AA OK or ENN | |
| * | |
| * c Resume at current address SNN ( signal NN) | |
| * cAA..AA Continue at address AA..AA SNN | |
| * | |
| * s Step one instruction SNN | |
| * sAA..AA Step one instruction from AA..AA SNN | |
| * | |
| * k kill | |
| * | |
| * ? What was the last sigval ? SNN (signal NN) | |
| * | |
| * bBB..BB Set baud rate to BB..BB OK or BNN, then sets | |
| * baud rate | |
| * | |
| * All commands and responses are sent with a packet which includes a | |
| * checksum. A packet consists of | |
| * | |
| * $<packet info>#<checksum>. | |
| * | |
| * where | |
| * <packet info> :: <characters representing the command or response> | |
| * <checksum> :: < two hex digits computed as modulo 256 sum of <packetinfo>> | |
| * | |
| * When a packet is received, it is first acknowledged with either '+' or '-'. | |
| * '+' indicates a successful transfer. '-' indicates a failed transfer. | |
| * | |
| * Example: | |
| * | |
| * Host: Reply: | |
| * $m0,10#2a +$00010203040506070809101112131415#42 | |
| * | |
| * | |
| * ============== | |
| * MORE EXAMPLES: | |
| * ============== | |
| * | |
| * For reference -- the following are the steps that one | |
| * company took (RidgeRun Inc) to get remote gdb debugging | |
| * going. In this scenario the host machine was a PC and the | |
| * target platform was a Galileo EVB64120A MIPS evaluation | |
| * board. | |
| * | |
| * Step 1: | |
| * First download gdb-5.0.tar.gz from the internet. | |
| * and then build/install the package. | |
| * | |
| * Example: | |
| * $ tar zxf gdb-5.0.tar.gz | |
| * $ cd gdb-5.0 | |
| * $ ./configure --target=frv-elf-gdb | |
| * $ make | |
| * $ frv-elf-gdb | |
| * | |
| * Step 2: | |
| * Configure linux for remote debugging and build it. | |
| * | |
| * Example: | |
| * $ cd ~/linux | |
| * $ make menuconfig <go to "Kernel Hacking" and turn on remote debugging> | |
| * $ make vmlinux | |
| * | |
| * Step 3: | |
| * Download the kernel to the remote target and start | |
| * the kernel running. It will promptly halt and wait | |
| * for the host gdb session to connect. It does this | |
| * since the "Kernel Hacking" option has defined | |
| * CONFIG_REMOTE_DEBUG which in turn enables your calls | |
| * to: | |
| * set_debug_traps(); | |
| * breakpoint(); | |
| * | |
| * Step 4: | |
| * Start the gdb session on the host. | |
| * | |
| * Example: | |
| * $ frv-elf-gdb vmlinux | |
| * (gdb) set remotebaud 115200 | |
| * (gdb) target remote /dev/ttyS1 | |
| * ...at this point you are connected to | |
| * the remote target and can use gdb | |
| * in the normal fasion. Setting | |
| * breakpoints, single stepping, | |
| * printing variables, etc. | |
| * | |
| */ | |
| #include <linux/string.h> | |
| #include <linux/kernel.h> | |
| #include <linux/signal.h> | |
| #include <linux/sched.h> | |
| #include <linux/mm.h> | |
| #include <linux/console.h> | |
| #include <linux/init.h> | |
| #include <linux/slab.h> | |
| #include <linux/nmi.h> | |
| #include <asm/asm-offsets.h> | |
| #include <asm/pgtable.h> | |
| #include <asm/gdb-stub.h> | |
| #define LEDS(x) do { /* *(u32*)0xe1200004 = ~(x); mb(); */ } while(0) | |
| #undef GDBSTUB_DEBUG_PROTOCOL | |
| extern void debug_to_serial(const char *p, int n); | |
| extern void gdbstub_console_write(struct console *co, const char *p, unsigned n); | |
| extern volatile uint32_t __break_error_detect[3]; /* ESFR1, ESR15, EAR15 */ | |
| struct __debug_amr { | |
| unsigned long L, P; | |
| } __attribute__((aligned(8))); | |
| struct __debug_mmu { | |
| struct { | |
| unsigned long hsr0, pcsr, esr0, ear0, epcr0; | |
| #ifdef CONFIG_MMU | |
| unsigned long tplr, tppr, tpxr, cxnr; | |
| #endif | |
| } regs; | |
| struct __debug_amr iamr[16]; | |
| struct __debug_amr damr[16]; | |
| #ifdef CONFIG_MMU | |
| struct __debug_amr tlb[64*2]; | |
| #endif | |
| }; | |
| static struct __debug_mmu __debug_mmu; | |
| /* | |
| * BUFMAX defines the maximum number of characters in inbound/outbound buffers | |
| * at least NUMREGBYTES*2 are needed for register packets | |
| */ | |
| #define BUFMAX 2048 | |
| #define BREAK_INSN 0x801000c0 /* use "break" as bkpt */ | |
| static const char gdbstub_banner[] = "Linux/FR-V GDB Stub (c) RedHat 2003\n"; | |
| volatile u8 gdbstub_rx_buffer[PAGE_SIZE] __attribute__((aligned(PAGE_SIZE))); | |
| volatile u32 gdbstub_rx_inp = 0; | |
| volatile u32 gdbstub_rx_outp = 0; | |
| volatile u8 gdbstub_rx_overflow = 0; | |
| u8 gdbstub_rx_unget = 0; | |
| /* set with GDB whilst running to permit step through exceptions */ | |
| extern volatile u32 __attribute__((section(".bss"))) gdbstub_trace_through_exceptions; | |
| static char input_buffer[BUFMAX]; | |
| static char output_buffer[BUFMAX]; | |
| static const char *regnames[] = { | |
| "PSR ", "ISR ", "CCR ", "CCCR", | |
| "LR ", "LCR ", "PC ", "_stt", | |
| "sys ", "GR8*", "GNE0", "GNE1", | |
| "IACH", "IACL", | |
| "TBR ", "SP ", "FP ", "GR3 ", | |
| "GR4 ", "GR5 ", "GR6 ", "GR7 ", | |
| "GR8 ", "GR9 ", "GR10", "GR11", | |
| "GR12", "GR13", "GR14", "GR15", | |
| "GR16", "GR17", "GR18", "GR19", | |
| "GR20", "GR21", "GR22", "GR23", | |
| "GR24", "GR25", "GR26", "GR27", | |
| "EFRM", "CURR", "GR30", "BFRM" | |
| }; | |
| struct gdbstub_bkpt { | |
| unsigned long addr; /* address of breakpoint */ | |
| unsigned len; /* size of breakpoint */ | |
| uint32_t originsns[7]; /* original instructions */ | |
| }; | |
| static struct gdbstub_bkpt gdbstub_bkpts[256]; | |
| /* | |
| * local prototypes | |
| */ | |
| static void gdbstub_recv_packet(char *buffer); | |
| static int gdbstub_send_packet(char *buffer); | |
| static int gdbstub_compute_signal(unsigned long tbr); | |
| static int hex(unsigned char ch); | |
| static int hexToInt(char **ptr, unsigned long *intValue); | |
| static unsigned char *mem2hex(const void *mem, char *buf, int count, int may_fault); | |
| static char *hex2mem(const char *buf, void *_mem, int count); | |
| /* | |
| * Convert ch from a hex digit to an int | |
| */ | |
| static int hex(unsigned char ch) | |
| { | |
| if (ch >= 'a' && ch <= 'f') | |
| return ch-'a'+10; | |
| if (ch >= '0' && ch <= '9') | |
| return ch-'0'; | |
| if (ch >= 'A' && ch <= 'F') | |
| return ch-'A'+10; | |
| return -1; | |
| } | |
| void gdbstub_printk(const char *fmt, ...) | |
| { | |
| static char buf[1024]; | |
| va_list args; | |
| int len; | |
| /* Emit the output into the temporary buffer */ | |
| va_start(args, fmt); | |
| len = vsnprintf(buf, sizeof(buf), fmt, args); | |
| va_end(args); | |
| debug_to_serial(buf, len); | |
| } | |
| static inline char *gdbstub_strcpy(char *dst, const char *src) | |
| { | |
| int loop = 0; | |
| while ((dst[loop] = src[loop])) | |
| loop++; | |
| return dst; | |
| } | |
| static void gdbstub_purge_cache(void) | |
| { | |
| asm volatile(" dcef @(gr0,gr0),#1 \n" | |
| " icei @(gr0,gr0),#1 \n" | |
| " membar \n" | |
| " bar \n" | |
| ); | |
| } | |
| /*****************************************************************************/ | |
| /* | |
| * scan for the sequence $<data>#<checksum> | |
| */ | |
| static void gdbstub_recv_packet(char *buffer) | |
| { | |
| unsigned char checksum; | |
| unsigned char xmitcsum; | |
| unsigned char ch; | |
| int count, i, ret, error; | |
| for (;;) { | |
| /* wait around for the start character, ignore all other characters */ | |
| do { | |
| gdbstub_rx_char(&ch, 0); | |
| } while (ch != '$'); | |
| checksum = 0; | |
| xmitcsum = -1; | |
| count = 0; | |
| error = 0; | |
| /* now, read until a # or end of buffer is found */ | |
| while (count < BUFMAX) { | |
| ret = gdbstub_rx_char(&ch, 0); | |
| if (ret < 0) | |
| error = ret; | |
| if (ch == '#') | |
| break; | |
| checksum += ch; | |
| buffer[count] = ch; | |
| count++; | |
| } | |
| if (error == -EIO) { | |
| gdbstub_proto("### GDB Rx Error - Skipping packet ###\n"); | |
| gdbstub_proto("### GDB Tx NAK\n"); | |
| gdbstub_tx_char('-'); | |
| continue; | |
| } | |
| if (count >= BUFMAX || error) | |
| continue; | |
| buffer[count] = 0; | |
| /* read the checksum */ | |
| ret = gdbstub_rx_char(&ch, 0); | |
| if (ret < 0) | |
| error = ret; | |
| xmitcsum = hex(ch) << 4; | |
| ret = gdbstub_rx_char(&ch, 0); | |
| if (ret < 0) | |
| error = ret; | |
| xmitcsum |= hex(ch); | |
| if (error) { | |
| if (error == -EIO) | |
| gdbstub_proto("### GDB Rx Error - Skipping packet\n"); | |
| gdbstub_proto("### GDB Tx NAK\n"); | |
| gdbstub_tx_char('-'); | |
| continue; | |
| } | |
| /* check the checksum */ | |
| if (checksum != xmitcsum) { | |
| gdbstub_proto("### GDB Tx NAK\n"); | |
| gdbstub_tx_char('-'); /* failed checksum */ | |
| continue; | |
| } | |
| gdbstub_proto("### GDB Rx '$%s#%02x' ###\n", buffer, checksum); | |
| gdbstub_proto("### GDB Tx ACK\n"); | |
| gdbstub_tx_char('+'); /* successful transfer */ | |
| /* if a sequence char is present, reply the sequence ID */ | |
| if (buffer[2] == ':') { | |
| gdbstub_tx_char(buffer[0]); | |
| gdbstub_tx_char(buffer[1]); | |
| /* remove sequence chars from buffer */ | |
| count = 0; | |
| while (buffer[count]) count++; | |
| for (i=3; i <= count; i++) | |
| buffer[i - 3] = buffer[i]; | |
| } | |
| break; | |
| } | |
| } /* end gdbstub_recv_packet() */ | |
| /*****************************************************************************/ | |
| /* | |
| * send the packet in buffer. | |
| * - return 0 if successfully ACK'd | |
| * - return 1 if abandoned due to new incoming packet | |
| */ | |
| static int gdbstub_send_packet(char *buffer) | |
| { | |
| unsigned char checksum; | |
| int count; | |
| unsigned char ch; | |
| /* $<packet info>#<checksum> */ | |
| gdbstub_proto("### GDB Tx '%s' ###\n", buffer); | |
| do { | |
| gdbstub_tx_char('$'); | |
| checksum = 0; | |
| count = 0; | |
| while ((ch = buffer[count]) != 0) { | |
| gdbstub_tx_char(ch); | |
| checksum += ch; | |
| count += 1; | |
| } | |
| gdbstub_tx_char('#'); | |
| gdbstub_tx_char(hex_asc_hi(checksum)); | |
| gdbstub_tx_char(hex_asc_lo(checksum)); | |
| } while (gdbstub_rx_char(&ch,0), | |
| #ifdef GDBSTUB_DEBUG_PROTOCOL | |
| ch=='-' && (gdbstub_proto("### GDB Rx NAK\n"),0), | |
| ch!='-' && ch!='+' && (gdbstub_proto("### GDB Rx ??? %02x\n",ch),0), | |
| #endif | |
| ch!='+' && ch!='$'); | |
| if (ch=='+') { | |
| gdbstub_proto("### GDB Rx ACK\n"); | |
| return 0; | |
| } | |
| gdbstub_proto("### GDB Tx Abandoned\n"); | |
| gdbstub_rx_unget = ch; | |
| return 1; | |
| } /* end gdbstub_send_packet() */ | |
| /* | |
| * While we find nice hex chars, build an int. | |
| * Return number of chars processed. | |
| */ | |
| static int hexToInt(char **ptr, unsigned long *_value) | |
| { | |
| int count = 0, ch; | |
| *_value = 0; | |
| while (**ptr) { | |
| ch = hex(**ptr); | |
| if (ch < 0) | |
| break; | |
| *_value = (*_value << 4) | ((uint8_t) ch & 0xf); | |
| count++; | |
| (*ptr)++; | |
| } | |
| return count; | |
| } | |
| /*****************************************************************************/ | |
| /* | |
| * probe an address to see whether it maps to anything | |
| */ | |
| static inline int gdbstub_addr_probe(const void *vaddr) | |
| { | |
| #ifdef CONFIG_MMU | |
| unsigned long paddr; | |
| asm("lrad %1,%0,#1,#0,#0" : "=r"(paddr) : "r"(vaddr)); | |
| if (!(paddr & xAMPRx_V)) | |
| return 0; | |
| #endif | |
| return 1; | |
| } /* end gdbstub_addr_probe() */ | |
| #ifdef CONFIG_MMU | |
| static unsigned long __saved_dampr, __saved_damlr; | |
| static inline unsigned long gdbstub_virt_to_pte(unsigned long vaddr) | |
| { | |
| pgd_t *pgd; | |
| pud_t *pud; | |
| pmd_t *pmd; | |
| pte_t *pte; | |
| unsigned long val, dampr5; | |
| pgd = (pgd_t *) __get_DAMLR(3) + pgd_index(vaddr); | |
| pud = pud_offset(pgd, vaddr); | |
| pmd = pmd_offset(pud, vaddr); | |
| if (pmd_bad(*pmd) || !pmd_present(*pmd)) | |
| return 0; | |
| /* make sure dampr5 maps to the correct pmd */ | |
| dampr5 = __get_DAMPR(5); | |
| val = pmd_val(*pmd); | |
| __set_DAMPR(5, val | xAMPRx_L | xAMPRx_SS_16Kb | xAMPRx_S | xAMPRx_C | xAMPRx_V); | |
| /* now its safe to access pmd */ | |
| pte = (pte_t *)__get_DAMLR(5) + __pte_index(vaddr); | |
| if (pte_present(*pte)) | |
| val = pte_val(*pte); | |
| else | |
| val = 0; | |
| /* restore original dampr5 */ | |
| __set_DAMPR(5, dampr5); | |
| return val; | |
| } | |
| #endif | |
| static inline int gdbstub_addr_map(const void *vaddr) | |
| { | |
| #ifdef CONFIG_MMU | |
| unsigned long pte; | |
| __saved_dampr = __get_DAMPR(2); | |
| __saved_damlr = __get_DAMLR(2); | |
| #endif | |
| if (gdbstub_addr_probe(vaddr)) | |
| return 1; | |
| #ifdef CONFIG_MMU | |
| pte = gdbstub_virt_to_pte((unsigned long) vaddr); | |
| if (pte) { | |
| __set_DAMPR(2, pte); | |
| __set_DAMLR(2, (unsigned long) vaddr & PAGE_MASK); | |
| return 1; | |
| } | |
| #endif | |
| return 0; | |
| } | |
| static inline void gdbstub_addr_unmap(void) | |
| { | |
| #ifdef CONFIG_MMU | |
| __set_DAMPR(2, __saved_dampr); | |
| __set_DAMLR(2, __saved_damlr); | |
| #endif | |
| } | |
| /* | |
| * access potentially dodgy memory through a potentially dodgy pointer | |
| */ | |
| static inline int gdbstub_read_dword(const void *addr, uint32_t *_res) | |
| { | |
| unsigned long brr; | |
| uint32_t res; | |
| if (!gdbstub_addr_map(addr)) | |
| return 0; | |
| asm volatile(" movgs gr0,brr \n" | |
| " ld%I2 %M2,%0 \n" | |
| " movsg brr,%1 \n" | |
| : "=r"(res), "=r"(brr) | |
| : "m"(*(uint32_t *) addr)); | |
| *_res = res; | |
| gdbstub_addr_unmap(); | |
| return likely(!brr); | |
| } | |
| static inline int gdbstub_write_dword(void *addr, uint32_t val) | |
| { | |
| unsigned long brr; | |
| if (!gdbstub_addr_map(addr)) | |
| return 0; | |
| asm volatile(" movgs gr0,brr \n" | |
| " st%I2 %1,%M2 \n" | |
| " movsg brr,%0 \n" | |
| : "=r"(brr) | |
| : "r"(val), "m"(*(uint32_t *) addr)); | |
| gdbstub_addr_unmap(); | |
| return likely(!brr); | |
| } | |
| static inline int gdbstub_read_word(const void *addr, uint16_t *_res) | |
| { | |
| unsigned long brr; | |
| uint16_t res; | |
| if (!gdbstub_addr_map(addr)) | |
| return 0; | |
| asm volatile(" movgs gr0,brr \n" | |
| " lduh%I2 %M2,%0 \n" | |
| " movsg brr,%1 \n" | |
| : "=r"(res), "=r"(brr) | |
| : "m"(*(uint16_t *) addr)); | |
| *_res = res; | |
| gdbstub_addr_unmap(); | |
| return likely(!brr); | |
| } | |
| static inline int gdbstub_write_word(void *addr, uint16_t val) | |
| { | |
| unsigned long brr; | |
| if (!gdbstub_addr_map(addr)) | |
| return 0; | |
| asm volatile(" movgs gr0,brr \n" | |
| " sth%I2 %1,%M2 \n" | |
| " movsg brr,%0 \n" | |
| : "=r"(brr) | |
| : "r"(val), "m"(*(uint16_t *) addr)); | |
| gdbstub_addr_unmap(); | |
| return likely(!brr); | |
| } | |
| static inline int gdbstub_read_byte(const void *addr, uint8_t *_res) | |
| { | |
| unsigned long brr; | |
| uint8_t res; | |
| if (!gdbstub_addr_map(addr)) | |
| return 0; | |
| asm volatile(" movgs gr0,brr \n" | |
| " ldub%I2 %M2,%0 \n" | |
| " movsg brr,%1 \n" | |
| : "=r"(res), "=r"(brr) | |
| : "m"(*(uint8_t *) addr)); | |
| *_res = res; | |
| gdbstub_addr_unmap(); | |
| return likely(!brr); | |
| } | |
| static inline int gdbstub_write_byte(void *addr, uint8_t val) | |
| { | |
| unsigned long brr; | |
| if (!gdbstub_addr_map(addr)) | |
| return 0; | |
| asm volatile(" movgs gr0,brr \n" | |
| " stb%I2 %1,%M2 \n" | |
| " movsg brr,%0 \n" | |
| : "=r"(brr) | |
| : "r"(val), "m"(*(uint8_t *) addr)); | |
| gdbstub_addr_unmap(); | |
| return likely(!brr); | |
| } | |
| static void __gdbstub_console_write(struct console *co, const char *p, unsigned n) | |
| { | |
| char outbuf[26]; | |
| int qty; | |
| outbuf[0] = 'O'; | |
| while (n > 0) { | |
| qty = 1; | |
| while (n > 0 && qty < 20) { | |
| mem2hex(p, outbuf + qty, 2, 0); | |
| qty += 2; | |
| if (*p == 0x0a) { | |
| outbuf[qty++] = '0'; | |
| outbuf[qty++] = 'd'; | |
| } | |
| p++; | |
| n--; | |
| } | |
| outbuf[qty] = 0; | |
| gdbstub_send_packet(outbuf); | |
| } | |
| } | |
| #if 0 | |
| void debug_to_serial(const char *p, int n) | |
| { | |
| gdbstub_console_write(NULL,p,n); | |
| } | |
| #endif | |
| #ifdef CONFIG_GDB_CONSOLE | |
| static struct console gdbstub_console = { | |
| .name = "gdb", | |
| .write = gdbstub_console_write, /* in break.S */ | |
| .flags = CON_PRINTBUFFER, | |
| .index = -1, | |
| }; | |
| #endif | |
| /*****************************************************************************/ | |
| /* | |
| * Convert the memory pointed to by mem into hex, placing result in buf. | |
| * - if successful, return a pointer to the last char put in buf (NUL) | |
| * - in case of mem fault, return NULL | |
| * may_fault is non-zero if we are reading from arbitrary memory, but is currently | |
| * not used. | |
| */ | |
| static unsigned char *mem2hex(const void *_mem, char *buf, int count, int may_fault) | |
| { | |
| const uint8_t *mem = _mem; | |
| uint8_t ch[4] __attribute__((aligned(4))); | |
| if ((uint32_t)mem&1 && count>=1) { | |
| if (!gdbstub_read_byte(mem,ch)) | |
| return NULL; | |
| buf = hex_byte_pack(buf, ch[0]); | |
| mem++; | |
| count--; | |
| } | |
| if ((uint32_t)mem&3 && count>=2) { | |
| if (!gdbstub_read_word(mem,(uint16_t *)ch)) | |
| return NULL; | |
| buf = hex_byte_pack(buf, ch[0]); | |
| buf = hex_byte_pack(buf, ch[1]); | |
| mem += 2; | |
| count -= 2; | |
| } | |
| while (count>=4) { | |
| if (!gdbstub_read_dword(mem,(uint32_t *)ch)) | |
| return NULL; | |
| buf = hex_byte_pack(buf, ch[0]); | |
| buf = hex_byte_pack(buf, ch[1]); | |
| buf = hex_byte_pack(buf, ch[2]); | |
| buf = hex_byte_pack(buf, ch[3]); | |
| mem += 4; | |
| count -= 4; | |
| } | |
| if (count>=2) { | |
| if (!gdbstub_read_word(mem,(uint16_t *)ch)) | |
| return NULL; | |
| buf = hex_byte_pack(buf, ch[0]); | |
| buf = hex_byte_pack(buf, ch[1]); | |
| mem += 2; | |
| count -= 2; | |
| } | |
| if (count>=1) { | |
| if (!gdbstub_read_byte(mem,ch)) | |
| return NULL; | |
| buf = hex_byte_pack(buf, ch[0]); | |
| } | |
| *buf = 0; | |
| return buf; | |
| } /* end mem2hex() */ | |
| /*****************************************************************************/ | |
| /* | |
| * convert the hex array pointed to by buf into binary to be placed in mem | |
| * return a pointer to the character AFTER the last byte of buffer consumed | |
| */ | |
| static char *hex2mem(const char *buf, void *_mem, int count) | |
| { | |
| uint8_t *mem = _mem; | |
| union { | |
| uint32_t l; | |
| uint16_t w; | |
| uint8_t b[4]; | |
| } ch; | |
| if ((u32)mem&1 && count>=1) { | |
| ch.b[0] = hex(*buf++) << 4; | |
| ch.b[0] |= hex(*buf++); | |
| if (!gdbstub_write_byte(mem,ch.b[0])) | |
| return NULL; | |
| mem++; | |
| count--; | |
| } | |
| if ((u32)mem&3 && count>=2) { | |
| ch.b[0] = hex(*buf++) << 4; | |
| ch.b[0] |= hex(*buf++); | |
| ch.b[1] = hex(*buf++) << 4; | |
| ch.b[1] |= hex(*buf++); | |
| if (!gdbstub_write_word(mem,ch.w)) | |
| return NULL; | |
| mem += 2; | |
| count -= 2; | |
| } | |
| while (count>=4) { | |
| ch.b[0] = hex(*buf++) << 4; | |
| ch.b[0] |= hex(*buf++); | |
| ch.b[1] = hex(*buf++) << 4; | |
| ch.b[1] |= hex(*buf++); | |
| ch.b[2] = hex(*buf++) << 4; | |
| ch.b[2] |= hex(*buf++); | |
| ch.b[3] = hex(*buf++) << 4; | |
| ch.b[3] |= hex(*buf++); | |
| if (!gdbstub_write_dword(mem,ch.l)) | |
| return NULL; | |
| mem += 4; | |
| count -= 4; | |
| } | |
| if (count>=2) { | |
| ch.b[0] = hex(*buf++) << 4; | |
| ch.b[0] |= hex(*buf++); | |
| ch.b[1] = hex(*buf++) << 4; | |
| ch.b[1] |= hex(*buf++); | |
| if (!gdbstub_write_word(mem,ch.w)) | |
| return NULL; | |
| mem += 2; | |
| count -= 2; | |
| } | |
| if (count>=1) { | |
| ch.b[0] = hex(*buf++) << 4; | |
| ch.b[0] |= hex(*buf++); | |
| if (!gdbstub_write_byte(mem,ch.b[0])) | |
| return NULL; | |
| } | |
| return (char *) buf; | |
| } /* end hex2mem() */ | |
| /*****************************************************************************/ | |
| /* | |
| * This table contains the mapping between FRV TBR.TT exception codes, | |
| * and signals, which are primarily what GDB understands. It also | |
| * indicates which hardware traps we need to commandeer when | |
| * initializing the stub. | |
| */ | |
| static const struct brr_to_sig_map { | |
| unsigned long brr_mask; /* BRR bitmask */ | |
| unsigned long tbr_tt; /* TBR.TT code (in BRR.EBTT) */ | |
| unsigned int signo; /* Signal that we map this into */ | |
| } brr_to_sig_map[] = { | |
| { BRR_EB, TBR_TT_INSTR_ACC_ERROR, SIGSEGV }, | |
| { BRR_EB, TBR_TT_ILLEGAL_INSTR, SIGILL }, | |
| { BRR_EB, TBR_TT_PRIV_INSTR, SIGILL }, | |
| { BRR_EB, TBR_TT_MP_EXCEPTION, SIGFPE }, | |
| { BRR_EB, TBR_TT_DATA_ACC_ERROR, SIGSEGV }, | |
| { BRR_EB, TBR_TT_DATA_STR_ERROR, SIGSEGV }, | |
| { BRR_EB, TBR_TT_DIVISION_EXCEP, SIGFPE }, | |
| { BRR_EB, TBR_TT_COMPOUND_EXCEP, SIGSEGV }, | |
| { BRR_EB, TBR_TT_INTERRUPT_13, SIGALRM }, /* watchdog */ | |
| { BRR_EB, TBR_TT_INTERRUPT_14, SIGINT }, /* GDB serial */ | |
| { BRR_EB, TBR_TT_INTERRUPT_15, SIGQUIT }, /* NMI */ | |
| { BRR_CB, 0, SIGUSR1 }, | |
| { BRR_TB, 0, SIGUSR2 }, | |
| { BRR_DBNEx, 0, SIGTRAP }, | |
| { BRR_DBx, 0, SIGTRAP }, /* h/w watchpoint */ | |
| { BRR_IBx, 0, SIGTRAP }, /* h/w breakpoint */ | |
| { BRR_CBB, 0, SIGTRAP }, | |
| { BRR_SB, 0, SIGTRAP }, | |
| { BRR_ST, 0, SIGTRAP }, /* single step */ | |
| { 0, 0, SIGHUP } /* default */ | |
| }; | |
| /*****************************************************************************/ | |
| /* | |
| * convert the FRV BRR register contents into a UNIX signal number | |
| */ | |
| static inline int gdbstub_compute_signal(unsigned long brr) | |
| { | |
| const struct brr_to_sig_map *map; | |
| unsigned long tbr = (brr & BRR_EBTT) >> 12; | |
| for (map = brr_to_sig_map; map->brr_mask; map++) | |
| if (map->brr_mask & brr) | |
| if (!map->tbr_tt || map->tbr_tt == tbr) | |
| break; | |
| return map->signo; | |
| } /* end gdbstub_compute_signal() */ | |
| /*****************************************************************************/ | |
| /* | |
| * set a software breakpoint or a hardware breakpoint or watchpoint | |
| */ | |
| static int gdbstub_set_breakpoint(unsigned long type, unsigned long addr, unsigned long len) | |
| { | |
| unsigned long tmp; | |
| int bkpt, loop, xloop; | |
| union { | |
| struct { | |
| unsigned long mask0, mask1; | |
| }; | |
| uint8_t bytes[8]; | |
| } dbmr; | |
| //gdbstub_printk("setbkpt(%ld,%08lx,%ld)\n", type, addr, len); | |
| switch (type) { | |
| /* set software breakpoint */ | |
| case 0: | |
| if (addr & 3 || len > 7*4) | |
| return -EINVAL; | |
| for (bkpt = 255; bkpt >= 0; bkpt--) | |
| if (!gdbstub_bkpts[bkpt].addr) | |
| break; | |
| if (bkpt < 0) | |
| return -ENOSPC; | |
| for (loop = 0; loop < len/4; loop++) | |
| if (!gdbstub_read_dword(&((uint32_t *) addr)[loop], | |
| &gdbstub_bkpts[bkpt].originsns[loop])) | |
| return -EFAULT; | |
| for (loop = 0; loop < len/4; loop++) | |
| if (!gdbstub_write_dword(&((uint32_t *) addr)[loop], | |
| BREAK_INSN) | |
| ) { | |
| /* need to undo the changes if possible */ | |
| for (xloop = 0; xloop < loop; xloop++) | |
| gdbstub_write_dword(&((uint32_t *) addr)[xloop], | |
| gdbstub_bkpts[bkpt].originsns[xloop]); | |
| return -EFAULT; | |
| } | |
| gdbstub_bkpts[bkpt].addr = addr; | |
| gdbstub_bkpts[bkpt].len = len; | |
| #if 0 | |
| gdbstub_printk("Set BKPT[%02x]: %08lx #%d {%04x, %04x} -> { %04x, %04x }\n", | |
| bkpt, | |
| gdbstub_bkpts[bkpt].addr, | |
| gdbstub_bkpts[bkpt].len, | |
| gdbstub_bkpts[bkpt].originsns[0], | |
| gdbstub_bkpts[bkpt].originsns[1], | |
| ((uint32_t *) addr)[0], | |
| ((uint32_t *) addr)[1] | |
| ); | |
| #endif | |
| return 0; | |
| /* set hardware breakpoint */ | |
| case 1: | |
| if (addr & 3 || len != 4) | |
| return -EINVAL; | |
| if (!(__debug_regs->dcr & DCR_IBE0)) { | |
| //gdbstub_printk("set h/w break 0: %08lx\n", addr); | |
| __debug_regs->dcr |= DCR_IBE0; | |
| __debug_regs->ibar[0] = addr; | |
| asm volatile("movgs %0,ibar0" : : "r"(addr)); | |
| return 0; | |
| } | |
| if (!(__debug_regs->dcr & DCR_IBE1)) { | |
| //gdbstub_printk("set h/w break 1: %08lx\n", addr); | |
| __debug_regs->dcr |= DCR_IBE1; | |
| __debug_regs->ibar[1] = addr; | |
| asm volatile("movgs %0,ibar1" : : "r"(addr)); | |
| return 0; | |
| } | |
| if (!(__debug_regs->dcr & DCR_IBE2)) { | |
| //gdbstub_printk("set h/w break 2: %08lx\n", addr); | |
| __debug_regs->dcr |= DCR_IBE2; | |
| __debug_regs->ibar[2] = addr; | |
| asm volatile("movgs %0,ibar2" : : "r"(addr)); | |
| return 0; | |
| } | |
| if (!(__debug_regs->dcr & DCR_IBE3)) { | |
| //gdbstub_printk("set h/w break 3: %08lx\n", addr); | |
| __debug_regs->dcr |= DCR_IBE3; | |
| __debug_regs->ibar[3] = addr; | |
| asm volatile("movgs %0,ibar3" : : "r"(addr)); | |
| return 0; | |
| } | |
| return -ENOSPC; | |
| /* set data read/write/access watchpoint */ | |
| case 2: | |
| case 3: | |
| case 4: | |
| if ((addr & ~7) != ((addr + len - 1) & ~7)) | |
| return -EINVAL; | |
| tmp = addr & 7; | |
| memset(dbmr.bytes, 0xff, sizeof(dbmr.bytes)); | |
| for (loop = 0; loop < len; loop++) | |
| dbmr.bytes[tmp + loop] = 0; | |
| addr &= ~7; | |
| if (!(__debug_regs->dcr & (DCR_DRBE0|DCR_DWBE0))) { | |
| //gdbstub_printk("set h/w watchpoint 0 type %ld: %08lx\n", type, addr); | |
| tmp = type==2 ? DCR_DWBE0 : type==3 ? DCR_DRBE0 : DCR_DRBE0|DCR_DWBE0; | |
| __debug_regs->dcr |= tmp; | |
| __debug_regs->dbar[0] = addr; | |
| __debug_regs->dbmr[0][0] = dbmr.mask0; | |
| __debug_regs->dbmr[0][1] = dbmr.mask1; | |
| __debug_regs->dbdr[0][0] = 0; | |
| __debug_regs->dbdr[0][1] = 0; | |
| asm volatile(" movgs %0,dbar0 \n" | |
| " movgs %1,dbmr00 \n" | |
| " movgs %2,dbmr01 \n" | |
| " movgs gr0,dbdr00 \n" | |
| " movgs gr0,dbdr01 \n" | |
| : : "r"(addr), "r"(dbmr.mask0), "r"(dbmr.mask1)); | |
| return 0; | |
| } | |
| if (!(__debug_regs->dcr & (DCR_DRBE1|DCR_DWBE1))) { | |
| //gdbstub_printk("set h/w watchpoint 1 type %ld: %08lx\n", type, addr); | |
| tmp = type==2 ? DCR_DWBE1 : type==3 ? DCR_DRBE1 : DCR_DRBE1|DCR_DWBE1; | |
| __debug_regs->dcr |= tmp; | |
| __debug_regs->dbar[1] = addr; | |
| __debug_regs->dbmr[1][0] = dbmr.mask0; | |
| __debug_regs->dbmr[1][1] = dbmr.mask1; | |
| __debug_regs->dbdr[1][0] = 0; | |
| __debug_regs->dbdr[1][1] = 0; | |
| asm volatile(" movgs %0,dbar1 \n" | |
| " movgs %1,dbmr10 \n" | |
| " movgs %2,dbmr11 \n" | |
| " movgs gr0,dbdr10 \n" | |
| " movgs gr0,dbdr11 \n" | |
| : : "r"(addr), "r"(dbmr.mask0), "r"(dbmr.mask1)); | |
| return 0; | |
| } | |
| return -ENOSPC; | |
| default: | |
| return -EINVAL; | |
| } | |
| } /* end gdbstub_set_breakpoint() */ | |
| /*****************************************************************************/ | |
| /* | |
| * clear a breakpoint or watchpoint | |
| */ | |
| int gdbstub_clear_breakpoint(unsigned long type, unsigned long addr, unsigned long len) | |
| { | |
| unsigned long tmp; | |
| int bkpt, loop; | |
| union { | |
| struct { | |
| unsigned long mask0, mask1; | |
| }; | |
| uint8_t bytes[8]; | |
| } dbmr; | |
| //gdbstub_printk("clearbkpt(%ld,%08lx,%ld)\n", type, addr, len); | |
| switch (type) { | |
| /* clear software breakpoint */ | |
| case 0: | |
| for (bkpt = 255; bkpt >= 0; bkpt--) | |
| if (gdbstub_bkpts[bkpt].addr == addr && gdbstub_bkpts[bkpt].len == len) | |
| break; | |
| if (bkpt < 0) | |
| return -ENOENT; | |
| gdbstub_bkpts[bkpt].addr = 0; | |
| for (loop = 0; loop < len/4; loop++) | |
| if (!gdbstub_write_dword(&((uint32_t *) addr)[loop], | |
| gdbstub_bkpts[bkpt].originsns[loop])) | |
| return -EFAULT; | |
| return 0; | |
| /* clear hardware breakpoint */ | |
| case 1: | |
| if (addr & 3 || len != 4) | |
| return -EINVAL; | |
| #define __get_ibar(X) ({ unsigned long x; asm volatile("movsg ibar"#X",%0" : "=r"(x)); x; }) | |
| if (__debug_regs->dcr & DCR_IBE0 && __get_ibar(0) == addr) { | |
| //gdbstub_printk("clear h/w break 0: %08lx\n", addr); | |
| __debug_regs->dcr &= ~DCR_IBE0; | |
| __debug_regs->ibar[0] = 0; | |
| asm volatile("movgs gr0,ibar0"); | |
| return 0; | |
| } | |
| if (__debug_regs->dcr & DCR_IBE1 && __get_ibar(1) == addr) { | |
| //gdbstub_printk("clear h/w break 1: %08lx\n", addr); | |
| __debug_regs->dcr &= ~DCR_IBE1; | |
| __debug_regs->ibar[1] = 0; | |
| asm volatile("movgs gr0,ibar1"); | |
| return 0; | |
| } | |
| if (__debug_regs->dcr & DCR_IBE2 && __get_ibar(2) == addr) { | |
| //gdbstub_printk("clear h/w break 2: %08lx\n", addr); | |
| __debug_regs->dcr &= ~DCR_IBE2; | |
| __debug_regs->ibar[2] = 0; | |
| asm volatile("movgs gr0,ibar2"); | |
| return 0; | |
| } | |
| if (__debug_regs->dcr & DCR_IBE3 && __get_ibar(3) == addr) { | |
| //gdbstub_printk("clear h/w break 3: %08lx\n", addr); | |
| __debug_regs->dcr &= ~DCR_IBE3; | |
| __debug_regs->ibar[3] = 0; | |
| asm volatile("movgs gr0,ibar3"); | |
| return 0; | |
| } | |
| return -EINVAL; | |
| /* clear data read/write/access watchpoint */ | |
| case 2: | |
| case 3: | |
| case 4: | |
| if ((addr & ~7) != ((addr + len - 1) & ~7)) | |
| return -EINVAL; | |
| tmp = addr & 7; | |
| memset(dbmr.bytes, 0xff, sizeof(dbmr.bytes)); | |
| for (loop = 0; loop < len; loop++) | |
| dbmr.bytes[tmp + loop] = 0; | |
| addr &= ~7; | |
| #define __get_dbar(X) ({ unsigned long x; asm volatile("movsg dbar"#X",%0" : "=r"(x)); x; }) | |
| #define __get_dbmr0(X) ({ unsigned long x; asm volatile("movsg dbmr"#X"0,%0" : "=r"(x)); x; }) | |
| #define __get_dbmr1(X) ({ unsigned long x; asm volatile("movsg dbmr"#X"1,%0" : "=r"(x)); x; }) | |
| /* consider DBAR 0 */ | |
| tmp = type==2 ? DCR_DWBE0 : type==3 ? DCR_DRBE0 : DCR_DRBE0|DCR_DWBE0; | |
| if ((__debug_regs->dcr & (DCR_DRBE0|DCR_DWBE0)) != tmp || | |
| __get_dbar(0) != addr || | |
| __get_dbmr0(0) != dbmr.mask0 || | |
| __get_dbmr1(0) != dbmr.mask1) | |
| goto skip_dbar0; | |
| //gdbstub_printk("clear h/w watchpoint 0 type %ld: %08lx\n", type, addr); | |
| __debug_regs->dcr &= ~(DCR_DRBE0|DCR_DWBE0); | |
| __debug_regs->dbar[0] = 0; | |
| __debug_regs->dbmr[0][0] = 0; | |
| __debug_regs->dbmr[0][1] = 0; | |
| __debug_regs->dbdr[0][0] = 0; | |
| __debug_regs->dbdr[0][1] = 0; | |
| asm volatile(" movgs gr0,dbar0 \n" | |
| " movgs gr0,dbmr00 \n" | |
| " movgs gr0,dbmr01 \n" | |
| " movgs gr0,dbdr00 \n" | |
| " movgs gr0,dbdr01 \n"); | |
| return 0; | |
| skip_dbar0: | |
| /* consider DBAR 0 */ | |
| tmp = type==2 ? DCR_DWBE1 : type==3 ? DCR_DRBE1 : DCR_DRBE1|DCR_DWBE1; | |
| if ((__debug_regs->dcr & (DCR_DRBE1|DCR_DWBE1)) != tmp || | |
| __get_dbar(1) != addr || | |
| __get_dbmr0(1) != dbmr.mask0 || | |
| __get_dbmr1(1) != dbmr.mask1) | |
| goto skip_dbar1; | |
| //gdbstub_printk("clear h/w watchpoint 1 type %ld: %08lx\n", type, addr); | |
| __debug_regs->dcr &= ~(DCR_DRBE1|DCR_DWBE1); | |
| __debug_regs->dbar[1] = 0; | |
| __debug_regs->dbmr[1][0] = 0; | |
| __debug_regs->dbmr[1][1] = 0; | |
| __debug_regs->dbdr[1][0] = 0; | |
| __debug_regs->dbdr[1][1] = 0; | |
| asm volatile(" movgs gr0,dbar1 \n" | |
| " movgs gr0,dbmr10 \n" | |
| " movgs gr0,dbmr11 \n" | |
| " movgs gr0,dbdr10 \n" | |
| " movgs gr0,dbdr11 \n"); | |
| return 0; | |
| skip_dbar1: | |
| return -ENOSPC; | |
| default: | |
| return -EINVAL; | |
| } | |
| } /* end gdbstub_clear_breakpoint() */ | |
| /*****************************************************************************/ | |
| /* | |
| * check a for an internal software breakpoint, and wind the PC back if necessary | |
| */ | |
| static void gdbstub_check_breakpoint(void) | |
| { | |
| unsigned long addr = __debug_frame->pc - 4; | |
| int bkpt; | |
| for (bkpt = 255; bkpt >= 0; bkpt--) | |
| if (gdbstub_bkpts[bkpt].addr == addr) | |
| break; | |
| if (bkpt >= 0) | |
| __debug_frame->pc = addr; | |
| //gdbstub_printk("alter pc [%d] %08lx\n", bkpt, __debug_frame->pc); | |
| } /* end gdbstub_check_breakpoint() */ | |
| /*****************************************************************************/ | |
| /* | |
| * | |
| */ | |
| static void __maybe_unused gdbstub_show_regs(void) | |
| { | |
| unsigned long *reg; | |
| int loop; | |
| gdbstub_printk("\n"); | |
| gdbstub_printk("Frame: @%p [%s]\n", | |
| __debug_frame, | |
| __debug_frame->psr & PSR_S ? "kernel" : "user"); | |
| reg = (unsigned long *) __debug_frame; | |
| for (loop = 0; loop < NR_PT_REGS; loop++) { | |
| printk("%s %08lx", regnames[loop + 0], reg[loop + 0]); | |
| if (loop == NR_PT_REGS - 1 || loop % 5 == 4) | |
| printk("\n"); | |
| else | |
| printk(" | "); | |
| } | |
| gdbstub_printk("Process %s (pid: %d)\n", current->comm, current->pid); | |
| } /* end gdbstub_show_regs() */ | |
| /*****************************************************************************/ | |
| /* | |
| * dump debugging regs | |
| */ | |
| static void __maybe_unused gdbstub_dump_debugregs(void) | |
| { | |
| gdbstub_printk("DCR %08lx ", __debug_status.dcr); | |
| gdbstub_printk("BRR %08lx\n", __debug_status.brr); | |
| gdbstub_printk("IBAR0 %08lx ", __get_ibar(0)); | |
| gdbstub_printk("IBAR1 %08lx ", __get_ibar(1)); | |
| gdbstub_printk("IBAR2 %08lx ", __get_ibar(2)); | |
| gdbstub_printk("IBAR3 %08lx\n", __get_ibar(3)); | |
| gdbstub_printk("DBAR0 %08lx ", __get_dbar(0)); | |
| gdbstub_printk("DBMR00 %08lx ", __get_dbmr0(0)); | |
| gdbstub_printk("DBMR01 %08lx\n", __get_dbmr1(0)); | |
| gdbstub_printk("DBAR1 %08lx ", __get_dbar(1)); | |
| gdbstub_printk("DBMR10 %08lx ", __get_dbmr0(1)); | |
| gdbstub_printk("DBMR11 %08lx\n", __get_dbmr1(1)); | |
| gdbstub_printk("\n"); | |
| } /* end gdbstub_dump_debugregs() */ | |
| /*****************************************************************************/ | |
| /* | |
| * dump the MMU state into a structure so that it can be accessed with GDB | |
| */ | |
| void gdbstub_get_mmu_state(void) | |
| { | |
| asm volatile("movsg hsr0,%0" : "=r"(__debug_mmu.regs.hsr0)); | |
| asm volatile("movsg pcsr,%0" : "=r"(__debug_mmu.regs.pcsr)); | |
| asm volatile("movsg esr0,%0" : "=r"(__debug_mmu.regs.esr0)); | |
| asm volatile("movsg ear0,%0" : "=r"(__debug_mmu.regs.ear0)); | |
| asm volatile("movsg epcr0,%0" : "=r"(__debug_mmu.regs.epcr0)); | |
| /* read the protection / SAT registers */ | |
| __debug_mmu.iamr[0].L = __get_IAMLR(0); | |
| __debug_mmu.iamr[0].P = __get_IAMPR(0); | |
| __debug_mmu.iamr[1].L = __get_IAMLR(1); | |
| __debug_mmu.iamr[1].P = __get_IAMPR(1); | |
| __debug_mmu.iamr[2].L = __get_IAMLR(2); | |
| __debug_mmu.iamr[2].P = __get_IAMPR(2); | |
| __debug_mmu.iamr[3].L = __get_IAMLR(3); | |
| __debug_mmu.iamr[3].P = __get_IAMPR(3); | |
| __debug_mmu.iamr[4].L = __get_IAMLR(4); | |
| __debug_mmu.iamr[4].P = __get_IAMPR(4); | |
| __debug_mmu.iamr[5].L = __get_IAMLR(5); | |
| __debug_mmu.iamr[5].P = __get_IAMPR(5); | |
| __debug_mmu.iamr[6].L = __get_IAMLR(6); | |
| __debug_mmu.iamr[6].P = __get_IAMPR(6); | |
| __debug_mmu.iamr[7].L = __get_IAMLR(7); | |
| __debug_mmu.iamr[7].P = __get_IAMPR(7); | |
| __debug_mmu.iamr[8].L = __get_IAMLR(8); | |
| __debug_mmu.iamr[8].P = __get_IAMPR(8); | |
| __debug_mmu.iamr[9].L = __get_IAMLR(9); | |
| __debug_mmu.iamr[9].P = __get_IAMPR(9); | |
| __debug_mmu.iamr[10].L = __get_IAMLR(10); | |
| __debug_mmu.iamr[10].P = __get_IAMPR(10); | |
| __debug_mmu.iamr[11].L = __get_IAMLR(11); | |
| __debug_mmu.iamr[11].P = __get_IAMPR(11); | |
| __debug_mmu.iamr[12].L = __get_IAMLR(12); | |
| __debug_mmu.iamr[12].P = __get_IAMPR(12); | |
| __debug_mmu.iamr[13].L = __get_IAMLR(13); | |
| __debug_mmu.iamr[13].P = __get_IAMPR(13); | |
| __debug_mmu.iamr[14].L = __get_IAMLR(14); | |
| __debug_mmu.iamr[14].P = __get_IAMPR(14); | |
| __debug_mmu.iamr[15].L = __get_IAMLR(15); | |
| __debug_mmu.iamr[15].P = __get_IAMPR(15); | |
| __debug_mmu.damr[0].L = __get_DAMLR(0); | |
| __debug_mmu.damr[0].P = __get_DAMPR(0); | |
| __debug_mmu.damr[1].L = __get_DAMLR(1); | |
| __debug_mmu.damr[1].P = __get_DAMPR(1); | |
| __debug_mmu.damr[2].L = __get_DAMLR(2); | |
| __debug_mmu.damr[2].P = __get_DAMPR(2); | |
| __debug_mmu.damr[3].L = __get_DAMLR(3); | |
| __debug_mmu.damr[3].P = __get_DAMPR(3); | |
| __debug_mmu.damr[4].L = __get_DAMLR(4); | |
| __debug_mmu.damr[4].P = __get_DAMPR(4); | |
| __debug_mmu.damr[5].L = __get_DAMLR(5); | |
| __debug_mmu.damr[5].P = __get_DAMPR(5); | |
| __debug_mmu.damr[6].L = __get_DAMLR(6); | |
| __debug_mmu.damr[6].P = __get_DAMPR(6); | |
| __debug_mmu.damr[7].L = __get_DAMLR(7); | |
| __debug_mmu.damr[7].P = __get_DAMPR(7); | |
| __debug_mmu.damr[8].L = __get_DAMLR(8); | |
| __debug_mmu.damr[8].P = __get_DAMPR(8); | |
| __debug_mmu.damr[9].L = __get_DAMLR(9); | |
| __debug_mmu.damr[9].P = __get_DAMPR(9); | |
| __debug_mmu.damr[10].L = __get_DAMLR(10); | |
| __debug_mmu.damr[10].P = __get_DAMPR(10); | |
| __debug_mmu.damr[11].L = __get_DAMLR(11); | |
| __debug_mmu.damr[11].P = __get_DAMPR(11); | |
| __debug_mmu.damr[12].L = __get_DAMLR(12); | |
| __debug_mmu.damr[12].P = __get_DAMPR(12); | |
| __debug_mmu.damr[13].L = __get_DAMLR(13); | |
| __debug_mmu.damr[13].P = __get_DAMPR(13); | |
| __debug_mmu.damr[14].L = __get_DAMLR(14); | |
| __debug_mmu.damr[14].P = __get_DAMPR(14); | |
| __debug_mmu.damr[15].L = __get_DAMLR(15); | |
| __debug_mmu.damr[15].P = __get_DAMPR(15); | |
| #ifdef CONFIG_MMU | |
| do { | |
| /* read the DAT entries from the TLB */ | |
| struct __debug_amr *p; | |
| int loop; | |
| asm volatile("movsg tplr,%0" : "=r"(__debug_mmu.regs.tplr)); | |
| asm volatile("movsg tppr,%0" : "=r"(__debug_mmu.regs.tppr)); | |
| asm volatile("movsg tpxr,%0" : "=r"(__debug_mmu.regs.tpxr)); | |
| asm volatile("movsg cxnr,%0" : "=r"(__debug_mmu.regs.cxnr)); | |
| p = __debug_mmu.tlb; | |
| /* way 0 */ | |
| asm volatile("movgs %0,tpxr" :: "r"(0 << TPXR_WAY_SHIFT)); | |
| for (loop = 0; loop < 64; loop++) { | |
| asm volatile("tlbpr %0,gr0,#1,#0" :: "r"(loop << PAGE_SHIFT)); | |
| asm volatile("movsg tplr,%0" : "=r"(p->L)); | |
| asm volatile("movsg tppr,%0" : "=r"(p->P)); | |
| p++; | |
| } | |
| /* way 1 */ | |
| asm volatile("movgs %0,tpxr" :: "r"(1 << TPXR_WAY_SHIFT)); | |
| for (loop = 0; loop < 64; loop++) { | |
| asm volatile("tlbpr %0,gr0,#1,#0" :: "r"(loop << PAGE_SHIFT)); | |
| asm volatile("movsg tplr,%0" : "=r"(p->L)); | |
| asm volatile("movsg tppr,%0" : "=r"(p->P)); | |
| p++; | |
| } | |
| asm volatile("movgs %0,tplr" :: "r"(__debug_mmu.regs.tplr)); | |
| asm volatile("movgs %0,tppr" :: "r"(__debug_mmu.regs.tppr)); | |
| asm volatile("movgs %0,tpxr" :: "r"(__debug_mmu.regs.tpxr)); | |
| } while(0); | |
| #endif | |
| } /* end gdbstub_get_mmu_state() */ | |
| /* | |
| * handle general query commands of the form 'qXXXXX' | |
| */ | |
| static void gdbstub_handle_query(void) | |
| { | |
| if (strcmp(input_buffer, "qAttached") == 0) { | |
| /* return current thread ID */ | |
| sprintf(output_buffer, "1"); | |
| return; | |
| } | |
| if (strcmp(input_buffer, "qC") == 0) { | |
| /* return current thread ID */ | |
| sprintf(output_buffer, "QC 0"); | |
| return; | |
| } | |
| if (strcmp(input_buffer, "qOffsets") == 0) { | |
| /* return relocation offset of text and data segments */ | |
| sprintf(output_buffer, "Text=0;Data=0;Bss=0"); | |
| return; | |
| } | |
| if (strcmp(input_buffer, "qSymbol::") == 0) { | |
| sprintf(output_buffer, "OK"); | |
| return; | |
| } | |
| if (strcmp(input_buffer, "qSupported") == 0) { | |
| /* query of supported features */ | |
| sprintf(output_buffer, "PacketSize=%u;ReverseContinue-;ReverseStep-", | |
| sizeof(input_buffer)); | |
| return; | |
| } | |
| gdbstub_strcpy(output_buffer,"E01"); | |
| } | |
| /*****************************************************************************/ | |
| /* | |
| * handle event interception and GDB remote protocol processing | |
| * - on entry: | |
| * PSR.ET==0, PSR.S==1 and the CPU is in debug mode | |
| * __debug_frame points to the saved registers | |
| * __frame points to the kernel mode exception frame, if it was in kernel | |
| * mode when the break happened | |
| */ | |
| void gdbstub(int sigval) | |
| { | |
| unsigned long addr, length, loop, dbar, temp, temp2, temp3; | |
| uint32_t zero; | |
| char *ptr; | |
| int flush_cache = 0; | |
| LEDS(0x5000); | |
| if (sigval < 0) { | |
| #ifndef CONFIG_GDBSTUB_IMMEDIATE | |
| /* return immediately if GDB immediate activation option not set */ | |
| return; | |
| #else | |
| sigval = SIGINT; | |
| #endif | |
| } | |
| save_user_regs(&__debug_frame0->uc); | |
| #if 0 | |
| gdbstub_printk("--> gdbstub() %08x %p %08x %08x\n", | |
| __debug_frame->pc, | |
| __debug_frame, | |
| __debug_regs->brr, | |
| __debug_regs->bpsr); | |
| // gdbstub_show_regs(); | |
| #endif | |
| LEDS(0x5001); | |
| /* if we were interrupted by input on the serial gdbstub serial port, | |
| * restore the context prior to the interrupt so that we return to that | |
| * directly | |
| */ | |
| temp = (unsigned long) __entry_kerneltrap_table; | |
| temp2 = (unsigned long) __entry_usertrap_table; | |
| temp3 = __debug_frame->pc & ~15; | |
| if (temp3 == temp + TBR_TT_INTERRUPT_15 || | |
| temp3 == temp2 + TBR_TT_INTERRUPT_15 | |
| ) { | |
| asm volatile("movsg pcsr,%0" : "=r"(__debug_frame->pc)); | |
| __debug_frame->psr |= PSR_ET; | |
| __debug_frame->psr &= ~PSR_S; | |
| if (__debug_frame->psr & PSR_PS) | |
| __debug_frame->psr |= PSR_S; | |
| __debug_status.brr = (__debug_frame->tbr & TBR_TT) << 12; | |
| __debug_status.brr |= BRR_EB; | |
| sigval = SIGINT; | |
| } | |
| /* handle the decrement timer going off (FR451 only) */ | |
| if (temp3 == temp + TBR_TT_DECREMENT_TIMER || | |
| temp3 == temp2 + TBR_TT_DECREMENT_TIMER | |
| ) { | |
| asm volatile("movgs %0,timerd" :: "r"(10000000)); | |
| asm volatile("movsg pcsr,%0" : "=r"(__debug_frame->pc)); | |
| __debug_frame->psr |= PSR_ET; | |
| __debug_frame->psr &= ~PSR_S; | |
| if (__debug_frame->psr & PSR_PS) | |
| __debug_frame->psr |= PSR_S; | |
| __debug_status.brr = (__debug_frame->tbr & TBR_TT) << 12; | |
| __debug_status.brr |= BRR_EB; | |
| sigval = SIGXCPU; | |
| } | |
| LEDS(0x5002); | |
| /* after a BREAK insn, the PC lands on the far side of it */ | |
| if (__debug_status.brr & BRR_SB) | |
| gdbstub_check_breakpoint(); | |
| LEDS(0x5003); | |
| /* handle attempts to write console data via GDB "O" commands */ | |
| if (__debug_frame->pc == (unsigned long) gdbstub_console_write + 4) { | |
| __gdbstub_console_write((struct console *) __debug_frame->gr8, | |
| (const char *) __debug_frame->gr9, | |
| (unsigned) __debug_frame->gr10); | |
| goto done; | |
| } | |
| if (gdbstub_rx_unget) { | |
| sigval = SIGINT; | |
| goto packet_waiting; | |
| } | |
| if (!sigval) | |
| sigval = gdbstub_compute_signal(__debug_status.brr); | |
| LEDS(0x5004); | |
| /* send a message to the debugger's user saying what happened if it may | |
| * not be clear cut (we can't map exceptions onto signals properly) | |
| */ | |
| if (sigval != SIGINT && sigval != SIGTRAP && sigval != SIGILL) { | |
| static const char title[] = "Break "; | |
| static const char crlf[] = "\r\n"; | |
| unsigned long brr = __debug_status.brr; | |
| char hx; | |
| ptr = output_buffer; | |
| *ptr++ = 'O'; | |
| ptr = mem2hex(title, ptr, sizeof(title) - 1,0); | |
| hx = hex_asc_hi(brr >> 24); | |
| ptr = hex_byte_pack(ptr, hx); | |
| hx = hex_asc_lo(brr >> 24); | |
| ptr = hex_byte_pack(ptr, hx); | |
| hx = hex_asc_hi(brr >> 16); | |
| ptr = hex_byte_pack(ptr, hx); | |
| hx = hex_asc_lo(brr >> 16); | |
| ptr = hex_byte_pack(ptr, hx); | |
| hx = hex_asc_hi(brr >> 8); | |
| ptr = hex_byte_pack(ptr, hx); | |
| hx = hex_asc_lo(brr >> 8); | |
| ptr = hex_byte_pack(ptr, hx); | |
| hx = hex_asc_hi(brr); | |
| ptr = hex_byte_pack(ptr, hx); | |
| hx = hex_asc_lo(brr); | |
| ptr = hex_byte_pack(ptr, hx); | |
| ptr = mem2hex(crlf, ptr, sizeof(crlf) - 1, 0); | |
| *ptr = 0; | |
| gdbstub_send_packet(output_buffer); /* send it off... */ | |
| } | |
| LEDS(0x5005); | |
| /* tell the debugger that an exception has occurred */ | |
| ptr = output_buffer; | |
| /* Send trap type (converted to signal) */ | |
| *ptr++ = 'T'; | |
| ptr = hex_byte_pack(ptr, sigval); | |
| /* Send Error PC */ | |
| ptr = hex_byte_pack(ptr, GDB_REG_PC); | |
| *ptr++ = ':'; | |
| ptr = mem2hex(&__debug_frame->pc, ptr, 4, 0); | |
| *ptr++ = ';'; | |
| /* | |
| * Send frame pointer | |
| */ | |
| ptr = hex_byte_pack(ptr, GDB_REG_FP); | |
| *ptr++ = ':'; | |
| ptr = mem2hex(&__debug_frame->fp, ptr, 4, 0); | |
| *ptr++ = ';'; | |
| /* | |
| * Send stack pointer | |
| */ | |
| ptr = hex_byte_pack(ptr, GDB_REG_SP); | |
| *ptr++ = ':'; | |
| ptr = mem2hex(&__debug_frame->sp, ptr, 4, 0); | |
| *ptr++ = ';'; | |
| *ptr++ = 0; | |
| gdbstub_send_packet(output_buffer); /* send it off... */ | |
| LEDS(0x5006); | |
| packet_waiting: | |
| gdbstub_get_mmu_state(); | |
| /* wait for input from remote GDB */ | |
| while (1) { | |
| output_buffer[0] = 0; | |
| LEDS(0x5007); | |
| gdbstub_recv_packet(input_buffer); | |
| LEDS(0x5600 | input_buffer[0]); | |
| switch (input_buffer[0]) { | |
| /* request repeat of last signal number */ | |
| case '?': | |
| output_buffer[0] = 'S'; | |
| output_buffer[1] = hex_asc_hi(sigval); | |
| output_buffer[2] = hex_asc_lo(sigval); | |
| output_buffer[3] = 0; | |
| break; | |
| case 'd': | |
| /* toggle debug flag */ | |
| break; | |
| /* return the value of the CPU registers | |
| * - GR0, GR1, GR2, GR3, GR4, GR5, GR6, GR7, | |
| * - GR8, GR9, GR10, GR11, GR12, GR13, GR14, GR15, | |
| * - GR16, GR17, GR18, GR19, GR20, GR21, GR22, GR23, | |
| * - GR24, GR25, GR26, GR27, GR28, GR29, GR30, GR31, | |
| * - GR32, GR33, GR34, GR35, GR36, GR37, GR38, GR39, | |
| * - GR40, GR41, GR42, GR43, GR44, GR45, GR46, GR47, | |
| * - GR48, GR49, GR50, GR51, GR52, GR53, GR54, GR55, | |
| * - GR56, GR57, GR58, GR59, GR60, GR61, GR62, GR63, | |
| * - FP0, FP1, FP2, FP3, FP4, FP5, FP6, FP7, | |
| * - FP8, FP9, FP10, FP11, FP12, FP13, FP14, FP15, | |
| * - FP16, FP17, FP18, FP19, FP20, FP21, FP22, FP23, | |
| * - FP24, FP25, FP26, FP27, FP28, FP29, FP30, FP31, | |
| * - FP32, FP33, FP34, FP35, FP36, FP37, FP38, FP39, | |
| * - FP40, FP41, FP42, FP43, FP44, FP45, FP46, FP47, | |
| * - FP48, FP49, FP50, FP51, FP52, FP53, FP54, FP55, | |
| * - FP56, FP57, FP58, FP59, FP60, FP61, FP62, FP63, | |
| * - PC, PSR, CCR, CCCR, | |
| * - _X132, _X133, _X134 | |
| * - TBR, BRR, DBAR0, DBAR1, DBAR2, DBAR3, | |
| * - _X141, _X142, _X143, _X144, | |
| * - LR, LCR | |
| */ | |
| case 'g': | |
| zero = 0; | |
| ptr = output_buffer; | |
| /* deal with GR0, GR1-GR27, GR28-GR31, GR32-GR63 */ | |
| ptr = mem2hex(&zero, ptr, 4, 0); | |
| for (loop = 1; loop <= 27; loop++) | |
| ptr = mem2hex(&__debug_user_context->i.gr[loop], ptr, 4, 0); | |
| temp = (unsigned long) __frame; | |
| ptr = mem2hex(&temp, ptr, 4, 0); | |
| ptr = mem2hex(&__debug_user_context->i.gr[29], ptr, 4, 0); | |
| ptr = mem2hex(&__debug_user_context->i.gr[30], ptr, 4, 0); | |
| #ifdef CONFIG_MMU | |
| ptr = mem2hex(&__debug_user_context->i.gr[31], ptr, 4, 0); | |
| #else | |
| temp = (unsigned long) __debug_frame; | |
| ptr = mem2hex(&temp, ptr, 4, 0); | |
| #endif | |
| for (loop = 32; loop <= 63; loop++) | |
| ptr = mem2hex(&__debug_user_context->i.gr[loop], ptr, 4, 0); | |
| /* deal with FR0-FR63 */ | |
| for (loop = 0; loop <= 63; loop++) | |
| ptr = mem2hex(&__debug_user_context->f.fr[loop], ptr, 4, 0); | |
| /* deal with special registers */ | |
| ptr = mem2hex(&__debug_frame->pc, ptr, 4, 0); | |
| ptr = mem2hex(&__debug_frame->psr, ptr, 4, 0); | |
| ptr = mem2hex(&__debug_frame->ccr, ptr, 4, 0); | |
| ptr = mem2hex(&__debug_frame->cccr, ptr, 4, 0); | |
| ptr = mem2hex(&zero, ptr, 4, 0); | |
| ptr = mem2hex(&zero, ptr, 4, 0); | |
| ptr = mem2hex(&zero, ptr, 4, 0); | |
| ptr = mem2hex(&__debug_frame->tbr, ptr, 4, 0); | |
| ptr = mem2hex(&__debug_status.brr , ptr, 4, 0); | |
| asm volatile("movsg dbar0,%0" : "=r"(dbar)); | |
| ptr = mem2hex(&dbar, ptr, 4, 0); | |
| asm volatile("movsg dbar1,%0" : "=r"(dbar)); | |
| ptr = mem2hex(&dbar, ptr, 4, 0); | |
| asm volatile("movsg dbar2,%0" : "=r"(dbar)); | |
| ptr = mem2hex(&dbar, ptr, 4, 0); | |
| asm volatile("movsg dbar3,%0" : "=r"(dbar)); | |
| ptr = mem2hex(&dbar, ptr, 4, 0); | |
| asm volatile("movsg scr0,%0" : "=r"(dbar)); | |
| ptr = mem2hex(&dbar, ptr, 4, 0); | |
| asm volatile("movsg scr1,%0" : "=r"(dbar)); | |
| ptr = mem2hex(&dbar, ptr, 4, 0); | |
| asm volatile("movsg scr2,%0" : "=r"(dbar)); | |
| ptr = mem2hex(&dbar, ptr, 4, 0); | |
| asm volatile("movsg scr3,%0" : "=r"(dbar)); | |
| ptr = mem2hex(&dbar, ptr, 4, 0); | |
| ptr = mem2hex(&__debug_frame->lr, ptr, 4, 0); | |
| ptr = mem2hex(&__debug_frame->lcr, ptr, 4, 0); | |
| ptr = mem2hex(&__debug_frame->iacc0, ptr, 8, 0); | |
| ptr = mem2hex(&__debug_user_context->f.fsr[0], ptr, 4, 0); | |
| for (loop = 0; loop <= 7; loop++) | |
| ptr = mem2hex(&__debug_user_context->f.acc[loop], ptr, 4, 0); | |
| ptr = mem2hex(&__debug_user_context->f.accg, ptr, 8, 0); | |
| for (loop = 0; loop <= 1; loop++) | |
| ptr = mem2hex(&__debug_user_context->f.msr[loop], ptr, 4, 0); | |
| ptr = mem2hex(&__debug_frame->gner0, ptr, 4, 0); | |
| ptr = mem2hex(&__debug_frame->gner1, ptr, 4, 0); | |
| ptr = mem2hex(&__debug_user_context->f.fner[0], ptr, 4, 0); | |
| ptr = mem2hex(&__debug_user_context->f.fner[1], ptr, 4, 0); | |
| break; | |
| /* set the values of the CPU registers */ | |
| case 'G': | |
| ptr = &input_buffer[1]; | |
| /* deal with GR0, GR1-GR27, GR28-GR31, GR32-GR63 */ | |
| ptr = hex2mem(ptr, &temp, 4); | |
| for (loop = 1; loop <= 27; loop++) | |
| ptr = hex2mem(ptr, &__debug_user_context->i.gr[loop], 4); | |
| ptr = hex2mem(ptr, &temp, 4); | |
| __frame = (struct pt_regs *) temp; | |
| ptr = hex2mem(ptr, &__debug_frame->gr29, 4); | |
| ptr = hex2mem(ptr, &__debug_frame->gr30, 4); | |
| #ifdef CONFIG_MMU | |
| ptr = hex2mem(ptr, &__debug_frame->gr31, 4); | |
| #else | |
| ptr = hex2mem(ptr, &temp, 4); | |
| #endif | |
| for (loop = 32; loop <= 63; loop++) | |
| ptr = hex2mem(ptr, &__debug_user_context->i.gr[loop], 4); | |
| /* deal with FR0-FR63 */ | |
| for (loop = 0; loop <= 63; loop++) | |
| ptr = mem2hex(&__debug_user_context->f.fr[loop], ptr, 4, 0); | |
| /* deal with special registers */ | |
| ptr = hex2mem(ptr, &__debug_frame->pc, 4); | |
| ptr = hex2mem(ptr, &__debug_frame->psr, 4); | |
| ptr = hex2mem(ptr, &__debug_frame->ccr, 4); | |
| ptr = hex2mem(ptr, &__debug_frame->cccr,4); | |
| for (loop = 132; loop <= 140; loop++) | |
| ptr = hex2mem(ptr, &temp, 4); | |
| ptr = hex2mem(ptr, &temp, 4); | |
| asm volatile("movgs %0,scr0" :: "r"(temp)); | |
| ptr = hex2mem(ptr, &temp, 4); | |
| asm volatile("movgs %0,scr1" :: "r"(temp)); | |
| ptr = hex2mem(ptr, &temp, 4); | |
| asm volatile("movgs %0,scr2" :: "r"(temp)); | |
| ptr = hex2mem(ptr, &temp, 4); | |
| asm volatile("movgs %0,scr3" :: "r"(temp)); | |
| ptr = hex2mem(ptr, &__debug_frame->lr, 4); | |
| ptr = hex2mem(ptr, &__debug_frame->lcr, 4); | |
| ptr = hex2mem(ptr, &__debug_frame->iacc0, 8); | |
| ptr = hex2mem(ptr, &__debug_user_context->f.fsr[0], 4); | |
| for (loop = 0; loop <= 7; loop++) | |
| ptr = hex2mem(ptr, &__debug_user_context->f.acc[loop], 4); | |
| ptr = hex2mem(ptr, &__debug_user_context->f.accg, 8); | |
| for (loop = 0; loop <= 1; loop++) | |
| ptr = hex2mem(ptr, &__debug_user_context->f.msr[loop], 4); | |
| ptr = hex2mem(ptr, &__debug_frame->gner0, 4); | |
| ptr = hex2mem(ptr, &__debug_frame->gner1, 4); | |
| ptr = hex2mem(ptr, &__debug_user_context->f.fner[0], 4); | |
| ptr = hex2mem(ptr, &__debug_user_context->f.fner[1], 4); | |
| gdbstub_strcpy(output_buffer,"OK"); | |
| break; | |
| /* mAA..AA,LLLL Read LLLL bytes at address AA..AA */ | |
| case 'm': | |
| ptr = &input_buffer[1]; | |
| if (hexToInt(&ptr, &addr) && | |
| *ptr++ == ',' && | |
| hexToInt(&ptr, &length) | |
| ) { | |
| if (mem2hex((char *)addr, output_buffer, length, 1)) | |
| break; | |
| gdbstub_strcpy (output_buffer, "E03"); | |
| } | |
| else { | |
| gdbstub_strcpy(output_buffer,"E01"); | |
| } | |
| break; | |
| /* MAA..AA,LLLL: Write LLLL bytes at address AA.AA return OK */ | |
| case 'M': | |
| ptr = &input_buffer[1]; | |
| if (hexToInt(&ptr, &addr) && | |
| *ptr++ == ',' && | |
| hexToInt(&ptr, &length) && | |
| *ptr++ == ':' | |
| ) { | |
| if (hex2mem(ptr, (char *)addr, length)) { | |
| gdbstub_strcpy(output_buffer, "OK"); | |
| } | |
| else { | |
| gdbstub_strcpy(output_buffer, "E03"); | |
| } | |
| } | |
| else | |
| gdbstub_strcpy(output_buffer, "E02"); | |
| flush_cache = 1; | |
| break; | |
| /* pNN: Read value of reg N and return it */ | |
| case 'p': | |
| /* return no value, indicating that we don't support | |
| * this command and that gdb should use 'g' instead */ | |
| break; | |
| /* PNN,=RRRRRRRR: Write value R to reg N return OK */ | |
| case 'P': | |
| ptr = &input_buffer[1]; | |
| if (!hexToInt(&ptr, &addr) || | |
| *ptr++ != '=' || | |
| !hexToInt(&ptr, &temp) | |
| ) { | |
| gdbstub_strcpy(output_buffer, "E01"); | |
| break; | |
| } | |
| temp2 = 1; | |
| switch (addr) { | |
| case GDB_REG_GR(0): | |
| break; | |
| case GDB_REG_GR(1) ... GDB_REG_GR(63): | |
| __debug_user_context->i.gr[addr - GDB_REG_GR(0)] = temp; | |
| break; | |
| case GDB_REG_FR(0) ... GDB_REG_FR(63): | |
| __debug_user_context->f.fr[addr - GDB_REG_FR(0)] = temp; | |
| break; | |
| case GDB_REG_PC: | |
| __debug_user_context->i.pc = temp; | |
| break; | |
| case GDB_REG_PSR: | |
| __debug_user_context->i.psr = temp; | |
| break; | |
| case GDB_REG_CCR: | |
| __debug_user_context->i.ccr = temp; | |
| break; | |
| case GDB_REG_CCCR: | |
| __debug_user_context->i.cccr = temp; | |
| break; | |
| case GDB_REG_BRR: | |
| __debug_status.brr = temp; | |
| break; | |
| case GDB_REG_LR: | |
| __debug_user_context->i.lr = temp; | |
| break; | |
| case GDB_REG_LCR: | |
| __debug_user_context->i.lcr = temp; | |
| break; | |
| case GDB_REG_FSR0: | |
| __debug_user_context->f.fsr[0] = temp; | |
| break; | |
| case GDB_REG_ACC(0) ... GDB_REG_ACC(7): | |
| __debug_user_context->f.acc[addr - GDB_REG_ACC(0)] = temp; | |
| break; | |
| case GDB_REG_ACCG(0): | |
| *(uint32_t *) &__debug_user_context->f.accg[0] = temp; | |
| break; | |
| case GDB_REG_ACCG(4): | |
| *(uint32_t *) &__debug_user_context->f.accg[4] = temp; | |
| break; | |
| case GDB_REG_MSR(0) ... GDB_REG_MSR(1): | |
| __debug_user_context->f.msr[addr - GDB_REG_MSR(0)] = temp; | |
| break; | |
| case GDB_REG_GNER(0) ... GDB_REG_GNER(1): | |
| __debug_user_context->i.gner[addr - GDB_REG_GNER(0)] = temp; | |
| break; | |
| case GDB_REG_FNER(0) ... GDB_REG_FNER(1): | |
| __debug_user_context->f.fner[addr - GDB_REG_FNER(0)] = temp; | |
| break; | |
| default: | |
| temp2 = 0; | |
| break; | |
| } | |
| if (temp2) { | |
| gdbstub_strcpy(output_buffer, "OK"); | |
| } | |
| else { | |
| gdbstub_strcpy(output_buffer, "E02"); | |
| } | |
| break; | |
| /* cAA..AA Continue at address AA..AA(optional) */ | |
| case 'c': | |
| /* try to read optional parameter, pc unchanged if no parm */ | |
| ptr = &input_buffer[1]; | |
| if (hexToInt(&ptr, &addr)) | |
| __debug_frame->pc = addr; | |
| goto done; | |
| /* kill the program */ | |
| case 'k' : | |
| goto done; /* just continue */ | |
| /* detach */ | |
| case 'D': | |
| gdbstub_strcpy(output_buffer, "OK"); | |
| break; | |
| /* reset the whole machine (FIXME: system dependent) */ | |
| case 'r': | |
| break; | |
| /* step to next instruction */ | |
| case 's': | |
| __debug_regs->dcr |= DCR_SE; | |
| __debug_status.dcr |= DCR_SE; | |
| goto done; | |
| /* extended command */ | |
| case 'v': | |
| if (strcmp(input_buffer, "vCont?") == 0) { | |
| output_buffer[0] = 0; | |
| break; | |
| } | |
| goto unsupported_cmd; | |
| /* set baud rate (bBB) */ | |
| case 'b': | |
| ptr = &input_buffer[1]; | |
| if (!hexToInt(&ptr, &temp)) { | |
| gdbstub_strcpy(output_buffer,"B01"); | |
| break; | |
| } | |
| if (temp) { | |
| /* ack before changing speed */ | |
| gdbstub_send_packet("OK"); | |
| gdbstub_set_baud(temp); | |
| } | |
| break; | |
| /* set breakpoint */ | |
| case 'Z': | |
| ptr = &input_buffer[1]; | |
| if (!hexToInt(&ptr,&temp) || *ptr++ != ',' || | |
| !hexToInt(&ptr,&addr) || *ptr++ != ',' || | |
| !hexToInt(&ptr,&length) | |
| ) { | |
| gdbstub_strcpy(output_buffer,"E01"); | |
| break; | |
| } | |
| if (temp >= 5) { | |
| gdbstub_strcpy(output_buffer,"E03"); | |
| break; | |
| } | |
| if (gdbstub_set_breakpoint(temp, addr, length) < 0) { | |
| gdbstub_strcpy(output_buffer,"E03"); | |
| break; | |
| } | |
| if (temp == 0) | |
| flush_cache = 1; /* soft bkpt by modified memory */ | |
| gdbstub_strcpy(output_buffer,"OK"); | |
| break; | |
| /* clear breakpoint */ | |
| case 'z': | |
| ptr = &input_buffer[1]; | |
| if (!hexToInt(&ptr,&temp) || *ptr++ != ',' || | |
| !hexToInt(&ptr,&addr) || *ptr++ != ',' || | |
| !hexToInt(&ptr,&length) | |
| ) { | |
| gdbstub_strcpy(output_buffer,"E01"); | |
| break; | |
| } | |
| if (temp >= 5) { | |
| gdbstub_strcpy(output_buffer,"E03"); | |
| break; | |
| } | |
| if (gdbstub_clear_breakpoint(temp, addr, length) < 0) { | |
| gdbstub_strcpy(output_buffer,"E03"); | |
| break; | |
| } | |
| if (temp == 0) | |
| flush_cache = 1; /* soft bkpt by modified memory */ | |
| gdbstub_strcpy(output_buffer,"OK"); | |
| break; | |
| /* Thread-setting packet */ | |
| case 'H': | |
| gdbstub_strcpy(output_buffer, "OK"); | |
| break; | |
| case 'q': | |
| gdbstub_handle_query(); | |
| break; | |
| default: | |
| unsupported_cmd: | |
| gdbstub_proto("### GDB Unsupported Cmd '%s'\n",input_buffer); | |
| gdbstub_strcpy(output_buffer,"E01"); | |
| break; | |
| } | |
| /* reply to the request */ | |
| LEDS(0x5009); | |
| gdbstub_send_packet(output_buffer); | |
| } | |
| done: | |
| restore_user_regs(&__debug_frame0->uc); | |
| //gdbstub_dump_debugregs(); | |
| //gdbstub_printk("<-- gdbstub() %08x\n", __debug_frame->pc); | |
| /* need to flush the instruction cache before resuming, as we may have | |
| * deposited a breakpoint, and the icache probably has no way of | |
| * knowing that a data ref to some location may have changed something | |
| * that is in the instruction cache. NB: We flush both caches, just to | |
| * be sure... | |
| */ | |
| /* note: flushing the icache will clobber EAR0 on the FR451 */ | |
| if (flush_cache) | |
| gdbstub_purge_cache(); | |
| LEDS(0x5666); | |
| } /* end gdbstub() */ | |
| /*****************************************************************************/ | |
| /* | |
| * initialise the GDB stub | |
| */ | |
| void __init gdbstub_init(void) | |
| { | |
| #ifdef CONFIG_GDBSTUB_IMMEDIATE | |
| unsigned char ch; | |
| int ret; | |
| #endif | |
| gdbstub_printk("%s", gdbstub_banner); | |
| gdbstub_io_init(); | |
| /* try to talk to GDB (or anyone insane enough to want to type GDB protocol by hand) */ | |
| gdbstub_proto("### GDB Tx ACK\n"); | |
| gdbstub_tx_char('+'); /* 'hello world' */ | |
| #ifdef CONFIG_GDBSTUB_IMMEDIATE | |
| gdbstub_printk("GDB Stub waiting for packet\n"); | |
| /* | |
| * In case GDB is started before us, ack any packets | |
| * (presumably "$?#xx") sitting there. | |
| */ | |
| do { gdbstub_rx_char(&ch, 0); } while (ch != '$'); | |
| do { gdbstub_rx_char(&ch, 0); } while (ch != '#'); | |
| do { ret = gdbstub_rx_char(&ch, 0); } while (ret != 0); /* eat first csum byte */ | |
| do { ret = gdbstub_rx_char(&ch, 0); } while (ret != 0); /* eat second csum byte */ | |
| gdbstub_proto("### GDB Tx NAK\n"); | |
| gdbstub_tx_char('-'); /* nak it */ | |
| #else | |
| gdbstub_printk("GDB Stub set\n"); | |
| #endif | |
| #if 0 | |
| /* send banner */ | |
| ptr = output_buffer; | |
| *ptr++ = 'O'; | |
| ptr = mem2hex(gdbstub_banner, ptr, sizeof(gdbstub_banner) - 1, 0); | |
| gdbstub_send_packet(output_buffer); | |
| #endif | |
| #if defined(CONFIG_GDB_CONSOLE) && defined(CONFIG_GDBSTUB_IMMEDIATE) | |
| register_console(&gdbstub_console); | |
| #endif | |
| } /* end gdbstub_init() */ | |
| /*****************************************************************************/ | |
| /* | |
| * register the console at a more appropriate time | |
| */ | |
| #if defined (CONFIG_GDB_CONSOLE) && !defined(CONFIG_GDBSTUB_IMMEDIATE) | |
| static int __init gdbstub_postinit(void) | |
| { | |
| printk("registering console\n"); | |
| register_console(&gdbstub_console); | |
| return 0; | |
| } /* end gdbstub_postinit() */ | |
| __initcall(gdbstub_postinit); | |
| #endif | |
| /*****************************************************************************/ | |
| /* | |
| * send an exit message to GDB | |
| */ | |
| void gdbstub_exit(int status) | |
| { | |
| unsigned char checksum; | |
| int count; | |
| unsigned char ch; | |
| sprintf(output_buffer,"W%02x",status&0xff); | |
| gdbstub_tx_char('$'); | |
| checksum = 0; | |
| count = 0; | |
| while ((ch = output_buffer[count]) != 0) { | |
| gdbstub_tx_char(ch); | |
| checksum += ch; | |
| count += 1; | |
| } | |
| gdbstub_tx_char('#'); | |
| gdbstub_tx_char(hex_asc_hi(checksum)); | |
| gdbstub_tx_char(hex_asc_lo(checksum)); | |
| /* make sure the output is flushed, or else RedBoot might clobber it */ | |
| gdbstub_tx_char('-'); | |
| gdbstub_tx_flush(); | |
| } /* end gdbstub_exit() */ | |
| /*****************************************************************************/ | |
| /* | |
| * GDB wants to call malloc() and free() to allocate memory for calling kernel | |
| * functions directly from its command line | |
| */ | |
| static void *malloc(size_t size) __maybe_unused; | |
| static void *malloc(size_t size) | |
| { | |
| return kmalloc(size, GFP_ATOMIC); | |
| } | |
| static void free(void *p) __maybe_unused; | |
| static void free(void *p) | |
| { | |
| kfree(p); | |
| } | |
| static uint32_t ___get_HSR0(void) __maybe_unused; | |
| static uint32_t ___get_HSR0(void) | |
| { | |
| return __get_HSR(0); | |
| } | |
| static uint32_t ___set_HSR0(uint32_t x) __maybe_unused; | |
| static uint32_t ___set_HSR0(uint32_t x) | |
| { | |
| __set_HSR(0, x); | |
| return __get_HSR(0); | |
| } |