| /* | |
| * Analog Devices ADV7511 HDMI transmitter driver | |
| * | |
| * Copyright 2012 Analog Devices Inc. | |
| * | |
| * Licensed under the GPL-2. | |
| */ | |
| #include <linux/device.h> | |
| #include <linux/gpio/consumer.h> | |
| #include <linux/i2c.h> | |
| #include <linux/module.h> | |
| #include <linux/regmap.h> | |
| #include <linux/slab.h> | |
| #include <drm/drmP.h> | |
| #include <drm/drm_crtc_helper.h> | |
| #include <drm/drm_edid.h> | |
| #include <drm/drm_encoder_slave.h> | |
| #include "adv7511.h" | |
| struct adv7511 { | |
| struct i2c_client *i2c_main; | |
| struct i2c_client *i2c_edid; | |
| struct regmap *regmap; | |
| struct regmap *packet_memory_regmap; | |
| enum drm_connector_status status; | |
| bool powered; | |
| unsigned int f_tmds; | |
| unsigned int current_edid_segment; | |
| uint8_t edid_buf[256]; | |
| bool edid_read; | |
| wait_queue_head_t wq; | |
| struct drm_encoder *encoder; | |
| bool embedded_sync; | |
| enum adv7511_sync_polarity vsync_polarity; | |
| enum adv7511_sync_polarity hsync_polarity; | |
| bool rgb; | |
| struct edid *edid; | |
| struct gpio_desc *gpio_pd; | |
| }; | |
| static struct adv7511 *encoder_to_adv7511(struct drm_encoder *encoder) | |
| { | |
| return to_encoder_slave(encoder)->slave_priv; | |
| } | |
| /* ADI recommended values for proper operation. */ | |
| static const struct reg_sequence adv7511_fixed_registers[] = { | |
| { 0x98, 0x03 }, | |
| { 0x9a, 0xe0 }, | |
| { 0x9c, 0x30 }, | |
| { 0x9d, 0x61 }, | |
| { 0xa2, 0xa4 }, | |
| { 0xa3, 0xa4 }, | |
| { 0xe0, 0xd0 }, | |
| { 0xf9, 0x00 }, | |
| { 0x55, 0x02 }, | |
| }; | |
| /* ----------------------------------------------------------------------------- | |
| * Register access | |
| */ | |
| static const uint8_t adv7511_register_defaults[] = { | |
| 0x12, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 00 */ | |
| 0x00, 0x00, 0x01, 0x0e, 0xbc, 0x18, 0x01, 0x13, | |
| 0x25, 0x37, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 10 */ | |
| 0x46, 0x62, 0x04, 0xa8, 0x00, 0x00, 0x1c, 0x84, | |
| 0x1c, 0xbf, 0x04, 0xa8, 0x1e, 0x70, 0x02, 0x1e, /* 20 */ | |
| 0x00, 0x00, 0x04, 0xa8, 0x08, 0x12, 0x1b, 0xac, | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 30 */ | |
| 0x00, 0x00, 0x00, 0x80, 0x00, 0x00, 0x00, 0xb0, | |
| 0x00, 0x50, 0x90, 0x7e, 0x79, 0x70, 0x00, 0x00, /* 40 */ | |
| 0x00, 0xa8, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00, | |
| 0x00, 0x00, 0x02, 0x0d, 0x00, 0x00, 0x00, 0x00, /* 50 */ | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 60 */ | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, | |
| 0x01, 0x0a, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 70 */ | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 80 */ | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, | |
| 0x00, 0x00, 0x00, 0x00, 0xc0, 0x00, 0x00, 0x00, /* 90 */ | |
| 0x0b, 0x02, 0x00, 0x18, 0x5a, 0x60, 0x00, 0x00, | |
| 0x00, 0x00, 0x80, 0x80, 0x08, 0x04, 0x00, 0x00, /* a0 */ | |
| 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x40, 0x14, | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* b0 */ | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* c0 */ | |
| 0x00, 0x03, 0x00, 0x00, 0x02, 0x00, 0x01, 0x04, | |
| 0x30, 0xff, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, /* d0 */ | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x10, 0x01, | |
| 0x80, 0x75, 0x00, 0x00, 0x60, 0x00, 0x00, 0x00, /* e0 */ | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, | |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x75, 0x11, 0x00, /* f0 */ | |
| 0x00, 0x7c, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, | |
| }; | |
| static bool adv7511_register_volatile(struct device *dev, unsigned int reg) | |
| { | |
| switch (reg) { | |
| case ADV7511_REG_CHIP_REVISION: | |
| case ADV7511_REG_SPDIF_FREQ: | |
| case ADV7511_REG_CTS_AUTOMATIC1: | |
| case ADV7511_REG_CTS_AUTOMATIC2: | |
| case ADV7511_REG_VIC_DETECTED: | |
| case ADV7511_REG_VIC_SEND: | |
| case ADV7511_REG_AUX_VIC_DETECTED: | |
| case ADV7511_REG_STATUS: | |
| case ADV7511_REG_GC(1): | |
| case ADV7511_REG_INT(0): | |
| case ADV7511_REG_INT(1): | |
| case ADV7511_REG_PLL_STATUS: | |
| case ADV7511_REG_AN(0): | |
| case ADV7511_REG_AN(1): | |
| case ADV7511_REG_AN(2): | |
| case ADV7511_REG_AN(3): | |
| case ADV7511_REG_AN(4): | |
| case ADV7511_REG_AN(5): | |
| case ADV7511_REG_AN(6): | |
| case ADV7511_REG_AN(7): | |
| case ADV7511_REG_HDCP_STATUS: | |
| case ADV7511_REG_BCAPS: | |
| case ADV7511_REG_BKSV(0): | |
| case ADV7511_REG_BKSV(1): | |
| case ADV7511_REG_BKSV(2): | |
| case ADV7511_REG_BKSV(3): | |
| case ADV7511_REG_BKSV(4): | |
| case ADV7511_REG_DDC_STATUS: | |
| case ADV7511_REG_BSTATUS(0): | |
| case ADV7511_REG_BSTATUS(1): | |
| case ADV7511_REG_CHIP_ID_HIGH: | |
| case ADV7511_REG_CHIP_ID_LOW: | |
| return true; | |
| } | |
| return false; | |
| } | |
| static const struct regmap_config adv7511_regmap_config = { | |
| .reg_bits = 8, | |
| .val_bits = 8, | |
| .max_register = 0xff, | |
| .cache_type = REGCACHE_RBTREE, | |
| .reg_defaults_raw = adv7511_register_defaults, | |
| .num_reg_defaults_raw = ARRAY_SIZE(adv7511_register_defaults), | |
| .volatile_reg = adv7511_register_volatile, | |
| }; | |
| /* ----------------------------------------------------------------------------- | |
| * Hardware configuration | |
| */ | |
| static void adv7511_set_colormap(struct adv7511 *adv7511, bool enable, | |
| const uint16_t *coeff, | |
| unsigned int scaling_factor) | |
| { | |
| unsigned int i; | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(1), | |
| ADV7511_CSC_UPDATE_MODE, ADV7511_CSC_UPDATE_MODE); | |
| if (enable) { | |
| for (i = 0; i < 12; ++i) { | |
| regmap_update_bits(adv7511->regmap, | |
| ADV7511_REG_CSC_UPPER(i), | |
| 0x1f, coeff[i] >> 8); | |
| regmap_write(adv7511->regmap, | |
| ADV7511_REG_CSC_LOWER(i), | |
| coeff[i] & 0xff); | |
| } | |
| } | |
| if (enable) | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(0), | |
| 0xe0, 0x80 | (scaling_factor << 5)); | |
| else | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(0), | |
| 0x80, 0x00); | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(1), | |
| ADV7511_CSC_UPDATE_MODE, 0); | |
| } | |
| static int adv7511_packet_enable(struct adv7511 *adv7511, unsigned int packet) | |
| { | |
| if (packet & 0xff) | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE0, | |
| packet, 0xff); | |
| if (packet & 0xff00) { | |
| packet >>= 8; | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE1, | |
| packet, 0xff); | |
| } | |
| return 0; | |
| } | |
| static int adv7511_packet_disable(struct adv7511 *adv7511, unsigned int packet) | |
| { | |
| if (packet & 0xff) | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE0, | |
| packet, 0x00); | |
| if (packet & 0xff00) { | |
| packet >>= 8; | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE1, | |
| packet, 0x00); | |
| } | |
| return 0; | |
| } | |
| /* Coefficients for adv7511 color space conversion */ | |
| static const uint16_t adv7511_csc_ycbcr_to_rgb[] = { | |
| 0x0734, 0x04ad, 0x0000, 0x1c1b, | |
| 0x1ddc, 0x04ad, 0x1f24, 0x0135, | |
| 0x0000, 0x04ad, 0x087c, 0x1b77, | |
| }; | |
| static void adv7511_set_config_csc(struct adv7511 *adv7511, | |
| struct drm_connector *connector, | |
| bool rgb) | |
| { | |
| struct adv7511_video_config config; | |
| bool output_format_422, output_format_ycbcr; | |
| unsigned int mode; | |
| uint8_t infoframe[17]; | |
| if (adv7511->edid) | |
| config.hdmi_mode = drm_detect_hdmi_monitor(adv7511->edid); | |
| else | |
| config.hdmi_mode = false; | |
| hdmi_avi_infoframe_init(&config.avi_infoframe); | |
| config.avi_infoframe.scan_mode = HDMI_SCAN_MODE_UNDERSCAN; | |
| if (rgb) { | |
| config.csc_enable = false; | |
| config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB; | |
| } else { | |
| config.csc_scaling_factor = ADV7511_CSC_SCALING_4; | |
| config.csc_coefficents = adv7511_csc_ycbcr_to_rgb; | |
| if ((connector->display_info.color_formats & | |
| DRM_COLOR_FORMAT_YCRCB422) && | |
| config.hdmi_mode) { | |
| config.csc_enable = false; | |
| config.avi_infoframe.colorspace = | |
| HDMI_COLORSPACE_YUV422; | |
| } else { | |
| config.csc_enable = true; | |
| config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB; | |
| } | |
| } | |
| if (config.hdmi_mode) { | |
| mode = ADV7511_HDMI_CFG_MODE_HDMI; | |
| switch (config.avi_infoframe.colorspace) { | |
| case HDMI_COLORSPACE_YUV444: | |
| output_format_422 = false; | |
| output_format_ycbcr = true; | |
| break; | |
| case HDMI_COLORSPACE_YUV422: | |
| output_format_422 = true; | |
| output_format_ycbcr = true; | |
| break; | |
| default: | |
| output_format_422 = false; | |
| output_format_ycbcr = false; | |
| break; | |
| } | |
| } else { | |
| mode = ADV7511_HDMI_CFG_MODE_DVI; | |
| output_format_422 = false; | |
| output_format_ycbcr = false; | |
| } | |
| adv7511_packet_disable(adv7511, ADV7511_PACKET_ENABLE_AVI_INFOFRAME); | |
| adv7511_set_colormap(adv7511, config.csc_enable, | |
| config.csc_coefficents, | |
| config.csc_scaling_factor); | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG1, 0x81, | |
| (output_format_422 << 7) | output_format_ycbcr); | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_HDCP_HDMI_CFG, | |
| ADV7511_HDMI_CFG_MODE_MASK, mode); | |
| hdmi_avi_infoframe_pack(&config.avi_infoframe, infoframe, | |
| sizeof(infoframe)); | |
| /* The AVI infoframe id is not configurable */ | |
| regmap_bulk_write(adv7511->regmap, ADV7511_REG_AVI_INFOFRAME_VERSION, | |
| infoframe + 1, sizeof(infoframe) - 1); | |
| adv7511_packet_enable(adv7511, ADV7511_PACKET_ENABLE_AVI_INFOFRAME); | |
| } | |
| static void adv7511_set_link_config(struct adv7511 *adv7511, | |
| const struct adv7511_link_config *config) | |
| { | |
| /* | |
| * The input style values documented in the datasheet don't match the | |
| * hardware register field values :-( | |
| */ | |
| static const unsigned int input_styles[4] = { 0, 2, 1, 3 }; | |
| unsigned int clock_delay; | |
| unsigned int color_depth; | |
| unsigned int input_id; | |
| clock_delay = (config->clock_delay + 1200) / 400; | |
| color_depth = config->input_color_depth == 8 ? 3 | |
| : (config->input_color_depth == 10 ? 1 : 2); | |
| /* TODO Support input ID 6 */ | |
| if (config->input_colorspace != HDMI_COLORSPACE_YUV422) | |
| input_id = config->input_clock == ADV7511_INPUT_CLOCK_DDR | |
| ? 5 : 0; | |
| else if (config->input_clock == ADV7511_INPUT_CLOCK_DDR) | |
| input_id = config->embedded_sync ? 8 : 7; | |
| else if (config->input_clock == ADV7511_INPUT_CLOCK_2X) | |
| input_id = config->embedded_sync ? 4 : 3; | |
| else | |
| input_id = config->embedded_sync ? 2 : 1; | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG, 0xf, | |
| input_id); | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG1, 0x7e, | |
| (color_depth << 4) | | |
| (input_styles[config->input_style] << 2)); | |
| regmap_write(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG2, | |
| config->input_justification << 3); | |
| regmap_write(adv7511->regmap, ADV7511_REG_TIMING_GEN_SEQ, | |
| config->sync_pulse << 2); | |
| regmap_write(adv7511->regmap, 0xba, clock_delay << 5); | |
| adv7511->embedded_sync = config->embedded_sync; | |
| adv7511->hsync_polarity = config->hsync_polarity; | |
| adv7511->vsync_polarity = config->vsync_polarity; | |
| adv7511->rgb = config->input_colorspace == HDMI_COLORSPACE_RGB; | |
| } | |
| static void adv7511_power_on(struct adv7511 *adv7511) | |
| { | |
| adv7511->current_edid_segment = -1; | |
| regmap_write(adv7511->regmap, ADV7511_REG_INT(0), | |
| ADV7511_INT0_EDID_READY); | |
| regmap_write(adv7511->regmap, ADV7511_REG_INT(1), | |
| ADV7511_INT1_DDC_ERROR); | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER, | |
| ADV7511_POWER_POWER_DOWN, 0); | |
| /* | |
| * Per spec it is allowed to pulse the HDP signal to indicate that the | |
| * EDID information has changed. Some monitors do this when they wakeup | |
| * from standby or are enabled. When the HDP goes low the adv7511 is | |
| * reset and the outputs are disabled which might cause the monitor to | |
| * go to standby again. To avoid this we ignore the HDP pin for the | |
| * first few seconds after enabling the output. | |
| */ | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, | |
| ADV7511_REG_POWER2_HDP_SRC_MASK, | |
| ADV7511_REG_POWER2_HDP_SRC_NONE); | |
| /* | |
| * Most of the registers are reset during power down or when HPD is low. | |
| */ | |
| regcache_sync(adv7511->regmap); | |
| adv7511->powered = true; | |
| } | |
| static void adv7511_power_off(struct adv7511 *adv7511) | |
| { | |
| /* TODO: setup additional power down modes */ | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER, | |
| ADV7511_POWER_POWER_DOWN, | |
| ADV7511_POWER_POWER_DOWN); | |
| regcache_mark_dirty(adv7511->regmap); | |
| adv7511->powered = false; | |
| } | |
| /* ----------------------------------------------------------------------------- | |
| * Interrupt and hotplug detection | |
| */ | |
| static bool adv7511_hpd(struct adv7511 *adv7511) | |
| { | |
| unsigned int irq0; | |
| int ret; | |
| ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0); | |
| if (ret < 0) | |
| return false; | |
| if (irq0 & ADV7511_INT0_HDP) { | |
| regmap_write(adv7511->regmap, ADV7511_REG_INT(0), | |
| ADV7511_INT0_HDP); | |
| return true; | |
| } | |
| return false; | |
| } | |
| static int adv7511_irq_process(struct adv7511 *adv7511) | |
| { | |
| unsigned int irq0, irq1; | |
| int ret; | |
| ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0); | |
| if (ret < 0) | |
| return ret; | |
| ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(1), &irq1); | |
| if (ret < 0) | |
| return ret; | |
| regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0); | |
| regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1); | |
| if (irq0 & ADV7511_INT0_HDP && adv7511->encoder) | |
| drm_helper_hpd_irq_event(adv7511->encoder->dev); | |
| if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) { | |
| adv7511->edid_read = true; | |
| if (adv7511->i2c_main->irq) | |
| wake_up_all(&adv7511->wq); | |
| } | |
| return 0; | |
| } | |
| static irqreturn_t adv7511_irq_handler(int irq, void *devid) | |
| { | |
| struct adv7511 *adv7511 = devid; | |
| int ret; | |
| ret = adv7511_irq_process(adv7511); | |
| return ret < 0 ? IRQ_NONE : IRQ_HANDLED; | |
| } | |
| /* ----------------------------------------------------------------------------- | |
| * EDID retrieval | |
| */ | |
| static int adv7511_wait_for_edid(struct adv7511 *adv7511, int timeout) | |
| { | |
| int ret; | |
| if (adv7511->i2c_main->irq) { | |
| ret = wait_event_interruptible_timeout(adv7511->wq, | |
| adv7511->edid_read, msecs_to_jiffies(timeout)); | |
| } else { | |
| for (; timeout > 0; timeout -= 25) { | |
| ret = adv7511_irq_process(adv7511); | |
| if (ret < 0) | |
| break; | |
| if (adv7511->edid_read) | |
| break; | |
| msleep(25); | |
| } | |
| } | |
| return adv7511->edid_read ? 0 : -EIO; | |
| } | |
| static int adv7511_get_edid_block(void *data, u8 *buf, unsigned int block, | |
| size_t len) | |
| { | |
| struct adv7511 *adv7511 = data; | |
| struct i2c_msg xfer[2]; | |
| uint8_t offset; | |
| unsigned int i; | |
| int ret; | |
| if (len > 128) | |
| return -EINVAL; | |
| if (adv7511->current_edid_segment != block / 2) { | |
| unsigned int status; | |
| ret = regmap_read(adv7511->regmap, ADV7511_REG_DDC_STATUS, | |
| &status); | |
| if (ret < 0) | |
| return ret; | |
| if (status != 2) { | |
| adv7511->edid_read = false; | |
| regmap_write(adv7511->regmap, ADV7511_REG_EDID_SEGMENT, | |
| block); | |
| ret = adv7511_wait_for_edid(adv7511, 200); | |
| if (ret < 0) | |
| return ret; | |
| } | |
| /* Break this apart, hopefully more I2C controllers will | |
| * support 64 byte transfers than 256 byte transfers | |
| */ | |
| xfer[0].addr = adv7511->i2c_edid->addr; | |
| xfer[0].flags = 0; | |
| xfer[0].len = 1; | |
| xfer[0].buf = &offset; | |
| xfer[1].addr = adv7511->i2c_edid->addr; | |
| xfer[1].flags = I2C_M_RD; | |
| xfer[1].len = 64; | |
| xfer[1].buf = adv7511->edid_buf; | |
| offset = 0; | |
| for (i = 0; i < 4; ++i) { | |
| ret = i2c_transfer(adv7511->i2c_edid->adapter, xfer, | |
| ARRAY_SIZE(xfer)); | |
| if (ret < 0) | |
| return ret; | |
| else if (ret != 2) | |
| return -EIO; | |
| xfer[1].buf += 64; | |
| offset += 64; | |
| } | |
| adv7511->current_edid_segment = block / 2; | |
| } | |
| if (block % 2 == 0) | |
| memcpy(buf, adv7511->edid_buf, len); | |
| else | |
| memcpy(buf, adv7511->edid_buf + 128, len); | |
| return 0; | |
| } | |
| /* ----------------------------------------------------------------------------- | |
| * Encoder operations | |
| */ | |
| static int adv7511_get_modes(struct drm_encoder *encoder, | |
| struct drm_connector *connector) | |
| { | |
| struct adv7511 *adv7511 = encoder_to_adv7511(encoder); | |
| struct edid *edid; | |
| unsigned int count; | |
| /* Reading the EDID only works if the device is powered */ | |
| if (!adv7511->powered) { | |
| regmap_write(adv7511->regmap, ADV7511_REG_INT(0), | |
| ADV7511_INT0_EDID_READY); | |
| regmap_write(adv7511->regmap, ADV7511_REG_INT(1), | |
| ADV7511_INT1_DDC_ERROR); | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER, | |
| ADV7511_POWER_POWER_DOWN, 0); | |
| adv7511->current_edid_segment = -1; | |
| } | |
| edid = drm_do_get_edid(connector, adv7511_get_edid_block, adv7511); | |
| if (!adv7511->powered) | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER, | |
| ADV7511_POWER_POWER_DOWN, | |
| ADV7511_POWER_POWER_DOWN); | |
| kfree(adv7511->edid); | |
| adv7511->edid = edid; | |
| if (!edid) | |
| return 0; | |
| drm_mode_connector_update_edid_property(connector, edid); | |
| count = drm_add_edid_modes(connector, edid); | |
| adv7511_set_config_csc(adv7511, connector, adv7511->rgb); | |
| return count; | |
| } | |
| static void adv7511_encoder_dpms(struct drm_encoder *encoder, int mode) | |
| { | |
| struct adv7511 *adv7511 = encoder_to_adv7511(encoder); | |
| if (mode == DRM_MODE_DPMS_ON) | |
| adv7511_power_on(adv7511); | |
| else | |
| adv7511_power_off(adv7511); | |
| } | |
| static enum drm_connector_status | |
| adv7511_encoder_detect(struct drm_encoder *encoder, | |
| struct drm_connector *connector) | |
| { | |
| struct adv7511 *adv7511 = encoder_to_adv7511(encoder); | |
| enum drm_connector_status status; | |
| unsigned int val; | |
| bool hpd; | |
| int ret; | |
| ret = regmap_read(adv7511->regmap, ADV7511_REG_STATUS, &val); | |
| if (ret < 0) | |
| return connector_status_disconnected; | |
| if (val & ADV7511_STATUS_HPD) | |
| status = connector_status_connected; | |
| else | |
| status = connector_status_disconnected; | |
| hpd = adv7511_hpd(adv7511); | |
| /* The chip resets itself when the cable is disconnected, so in case | |
| * there is a pending HPD interrupt and the cable is connected there was | |
| * at least one transition from disconnected to connected and the chip | |
| * has to be reinitialized. */ | |
| if (status == connector_status_connected && hpd && adv7511->powered) { | |
| regcache_mark_dirty(adv7511->regmap); | |
| adv7511_power_on(adv7511); | |
| adv7511_get_modes(encoder, connector); | |
| if (adv7511->status == connector_status_connected) | |
| status = connector_status_disconnected; | |
| } else { | |
| /* Renable HDP sensing */ | |
| regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, | |
| ADV7511_REG_POWER2_HDP_SRC_MASK, | |
| ADV7511_REG_POWER2_HDP_SRC_BOTH); | |
| } | |
| adv7511->status = status; | |
| return status; | |
| } | |
| static int adv7511_encoder_mode_valid(struct drm_encoder *encoder, | |
| struct drm_display_mode *mode) | |
| { | |
| if (mode->clock > 165000) | |
| return MODE_CLOCK_HIGH; | |
| return MODE_OK; | |
| } | |
| static void adv7511_encoder_mode_set(struct drm_encoder *encoder, | |
| struct drm_display_mode *mode, | |
| struct drm_display_mode *adj_mode) | |
| { | |
| struct adv7511 *adv7511 = encoder_to_adv7511(encoder); | |
| unsigned int low_refresh_rate; | |
| unsigned int hsync_polarity = 0; | |
| unsigned int vsync_polarity = 0; | |
| if (adv7511->embedded_sync) { | |
| unsigned int hsync_offset, hsync_len; | |
| unsigned int vsync_offset, vsync_len; | |
| hsync_offset = adj_mode->crtc_hsync_start - | |
| adj_mode->crtc_hdisplay; | |
| vsync_offset = adj_mode->crtc_vsync_start - | |
| adj_mode->crtc_vdisplay; | |
| hsync_len = adj_mode->crtc_hsync_end - | |
| adj_mode->crtc_hsync_start; | |
| vsync_len = adj_mode->crtc_vsync_end - | |
| adj_mode->crtc_vsync_start; | |
| /* The hardware vsync generator has a off-by-one bug */ | |
| vsync_offset += 1; | |
| regmap_write(adv7511->regmap, ADV7511_REG_HSYNC_PLACEMENT_MSB, | |
| ((hsync_offset >> 10) & 0x7) << 5); | |
| regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(0), | |
| (hsync_offset >> 2) & 0xff); | |
| regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(1), | |
| ((hsync_offset & 0x3) << 6) | | |
| ((hsync_len >> 4) & 0x3f)); | |
| regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(2), | |
| ((hsync_len & 0xf) << 4) | | |
| ((vsync_offset >> 6) & 0xf)); | |
| regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(3), | |
| ((vsync_offset & 0x3f) << 2) | | |
| ((vsync_len >> 8) & 0x3)); | |
| regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(4), | |
| vsync_len & 0xff); | |
| hsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PHSYNC); | |
| vsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PVSYNC); | |
| } else { | |
| enum adv7511_sync_polarity mode_hsync_polarity; | |
| enum adv7511_sync_polarity mode_vsync_polarity; | |
| /** | |
| * If the input signal is always low or always high we want to | |
| * invert or let it passthrough depending on the polarity of the | |
| * current mode. | |
| **/ | |
| if (adj_mode->flags & DRM_MODE_FLAG_NHSYNC) | |
| mode_hsync_polarity = ADV7511_SYNC_POLARITY_LOW; | |
| else | |
| mode_hsync_polarity = ADV7511_SYNC_POLARITY_HIGH; | |
| if (adj_mode->flags & DRM_MODE_FLAG_NVSYNC) | |
| mode_vsync_polarity = ADV7511_SYNC_POLARITY_LOW; | |
| else | |
| mode_vsync_polarity = ADV7511_SYNC_POLARITY_HIGH; | |
| if (adv7511->hsync_polarity != mode_hsync_polarity && | |
| adv7511->hsync_polarity != | |
| ADV7511_SYNC_POLARITY_PASSTHROUGH) | |
| hsync_polarity = 1; | |
| if (adv7511->vsync_polarity != mode_vsync_polarity && | |
| adv7511->vsync_polarity != | |
| ADV7511_SYNC_POLARITY_PASSTHROUGH) | |
| vsync_polarity = 1; | |
| } | |
| if (mode->vrefresh <= 24000) | |
| low_refresh_rate = ADV7511_LOW_REFRESH_RATE_24HZ; | |
| else if (mode->vrefresh <= 25000) | |
| low_refresh_rate = ADV7511_LOW_REFRESH_RATE_25HZ; | |
| else if (mode->vrefresh <= 30000) | |
| low_refresh_rate = ADV7511_LOW_REFRESH_RATE_30HZ; | |
| else | |
| low_refresh_rate = ADV7511_LOW_REFRESH_RATE_NONE; | |
| regmap_update_bits(adv7511->regmap, 0xfb, | |
| 0x6, low_refresh_rate << 1); | |
| regmap_update_bits(adv7511->regmap, 0x17, | |
| 0x60, (vsync_polarity << 6) | (hsync_polarity << 5)); | |
| /* | |
| * TODO Test first order 4:2:2 to 4:4:4 up conversion method, which is | |
| * supposed to give better results. | |
| */ | |
| adv7511->f_tmds = mode->clock; | |
| } | |
| static struct drm_encoder_slave_funcs adv7511_encoder_funcs = { | |
| .dpms = adv7511_encoder_dpms, | |
| .mode_valid = adv7511_encoder_mode_valid, | |
| .mode_set = adv7511_encoder_mode_set, | |
| .detect = adv7511_encoder_detect, | |
| .get_modes = adv7511_get_modes, | |
| }; | |
| /* ----------------------------------------------------------------------------- | |
| * Probe & remove | |
| */ | |
| static int adv7511_parse_dt(struct device_node *np, | |
| struct adv7511_link_config *config) | |
| { | |
| const char *str; | |
| int ret; | |
| memset(config, 0, sizeof(*config)); | |
| of_property_read_u32(np, "adi,input-depth", &config->input_color_depth); | |
| if (config->input_color_depth != 8 && config->input_color_depth != 10 && | |
| config->input_color_depth != 12) | |
| return -EINVAL; | |
| ret = of_property_read_string(np, "adi,input-colorspace", &str); | |
| if (ret < 0) | |
| return ret; | |
| if (!strcmp(str, "rgb")) | |
| config->input_colorspace = HDMI_COLORSPACE_RGB; | |
| else if (!strcmp(str, "yuv422")) | |
| config->input_colorspace = HDMI_COLORSPACE_YUV422; | |
| else if (!strcmp(str, "yuv444")) | |
| config->input_colorspace = HDMI_COLORSPACE_YUV444; | |
| else | |
| return -EINVAL; | |
| ret = of_property_read_string(np, "adi,input-clock", &str); | |
| if (ret < 0) | |
| return ret; | |
| if (!strcmp(str, "1x")) | |
| config->input_clock = ADV7511_INPUT_CLOCK_1X; | |
| else if (!strcmp(str, "2x")) | |
| config->input_clock = ADV7511_INPUT_CLOCK_2X; | |
| else if (!strcmp(str, "ddr")) | |
| config->input_clock = ADV7511_INPUT_CLOCK_DDR; | |
| else | |
| return -EINVAL; | |
| if (config->input_colorspace == HDMI_COLORSPACE_YUV422 || | |
| config->input_clock != ADV7511_INPUT_CLOCK_1X) { | |
| ret = of_property_read_u32(np, "adi,input-style", | |
| &config->input_style); | |
| if (ret) | |
| return ret; | |
| if (config->input_style < 1 || config->input_style > 3) | |
| return -EINVAL; | |
| ret = of_property_read_string(np, "adi,input-justification", | |
| &str); | |
| if (ret < 0) | |
| return ret; | |
| if (!strcmp(str, "left")) | |
| config->input_justification = | |
| ADV7511_INPUT_JUSTIFICATION_LEFT; | |
| else if (!strcmp(str, "evenly")) | |
| config->input_justification = | |
| ADV7511_INPUT_JUSTIFICATION_EVENLY; | |
| else if (!strcmp(str, "right")) | |
| config->input_justification = | |
| ADV7511_INPUT_JUSTIFICATION_RIGHT; | |
| else | |
| return -EINVAL; | |
| } else { | |
| config->input_style = 1; | |
| config->input_justification = ADV7511_INPUT_JUSTIFICATION_LEFT; | |
| } | |
| of_property_read_u32(np, "adi,clock-delay", &config->clock_delay); | |
| if (config->clock_delay < -1200 || config->clock_delay > 1600) | |
| return -EINVAL; | |
| config->embedded_sync = of_property_read_bool(np, "adi,embedded-sync"); | |
| /* Hardcode the sync pulse configurations for now. */ | |
| config->sync_pulse = ADV7511_INPUT_SYNC_PULSE_NONE; | |
| config->vsync_polarity = ADV7511_SYNC_POLARITY_PASSTHROUGH; | |
| config->hsync_polarity = ADV7511_SYNC_POLARITY_PASSTHROUGH; | |
| return 0; | |
| } | |
| static const int edid_i2c_addr = 0x7e; | |
| static const int packet_i2c_addr = 0x70; | |
| static const int cec_i2c_addr = 0x78; | |
| static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id) | |
| { | |
| struct adv7511_link_config link_config; | |
| struct adv7511 *adv7511; | |
| struct device *dev = &i2c->dev; | |
| unsigned int val; | |
| int ret; | |
| if (!dev->of_node) | |
| return -EINVAL; | |
| adv7511 = devm_kzalloc(dev, sizeof(*adv7511), GFP_KERNEL); | |
| if (!adv7511) | |
| return -ENOMEM; | |
| adv7511->powered = false; | |
| adv7511->status = connector_status_disconnected; | |
| ret = adv7511_parse_dt(dev->of_node, &link_config); | |
| if (ret) | |
| return ret; | |
| /* | |
| * The power down GPIO is optional. If present, toggle it from active to | |
| * inactive to wake up the encoder. | |
| */ | |
| adv7511->gpio_pd = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH); | |
| if (IS_ERR(adv7511->gpio_pd)) | |
| return PTR_ERR(adv7511->gpio_pd); | |
| if (adv7511->gpio_pd) { | |
| mdelay(5); | |
| gpiod_set_value_cansleep(adv7511->gpio_pd, 0); | |
| } | |
| adv7511->regmap = devm_regmap_init_i2c(i2c, &adv7511_regmap_config); | |
| if (IS_ERR(adv7511->regmap)) | |
| return PTR_ERR(adv7511->regmap); | |
| ret = regmap_read(adv7511->regmap, ADV7511_REG_CHIP_REVISION, &val); | |
| if (ret) | |
| return ret; | |
| dev_dbg(dev, "Rev. %d\n", val); | |
| ret = regmap_register_patch(adv7511->regmap, adv7511_fixed_registers, | |
| ARRAY_SIZE(adv7511_fixed_registers)); | |
| if (ret) | |
| return ret; | |
| regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR, edid_i2c_addr); | |
| regmap_write(adv7511->regmap, ADV7511_REG_PACKET_I2C_ADDR, | |
| packet_i2c_addr); | |
| regmap_write(adv7511->regmap, ADV7511_REG_CEC_I2C_ADDR, cec_i2c_addr); | |
| adv7511_packet_disable(adv7511, 0xffff); | |
| adv7511->i2c_main = i2c; | |
| adv7511->i2c_edid = i2c_new_dummy(i2c->adapter, edid_i2c_addr >> 1); | |
| if (!adv7511->i2c_edid) | |
| return -ENOMEM; | |
| if (i2c->irq) { | |
| init_waitqueue_head(&adv7511->wq); | |
| ret = devm_request_threaded_irq(dev, i2c->irq, NULL, | |
| adv7511_irq_handler, | |
| IRQF_ONESHOT, dev_name(dev), | |
| adv7511); | |
| if (ret) | |
| goto err_i2c_unregister_device; | |
| } | |
| /* CEC is unused for now */ | |
| regmap_write(adv7511->regmap, ADV7511_REG_CEC_CTRL, | |
| ADV7511_CEC_CTRL_POWER_DOWN); | |
| adv7511_power_off(adv7511); | |
| i2c_set_clientdata(i2c, adv7511); | |
| adv7511_set_link_config(adv7511, &link_config); | |
| return 0; | |
| err_i2c_unregister_device: | |
| i2c_unregister_device(adv7511->i2c_edid); | |
| return ret; | |
| } | |
| static int adv7511_remove(struct i2c_client *i2c) | |
| { | |
| struct adv7511 *adv7511 = i2c_get_clientdata(i2c); | |
| i2c_unregister_device(adv7511->i2c_edid); | |
| kfree(adv7511->edid); | |
| return 0; | |
| } | |
| static int adv7511_encoder_init(struct i2c_client *i2c, struct drm_device *dev, | |
| struct drm_encoder_slave *encoder) | |
| { | |
| struct adv7511 *adv7511 = i2c_get_clientdata(i2c); | |
| encoder->slave_priv = adv7511; | |
| encoder->slave_funcs = &adv7511_encoder_funcs; | |
| adv7511->encoder = &encoder->base; | |
| return 0; | |
| } | |
| static const struct i2c_device_id adv7511_i2c_ids[] = { | |
| { "adv7511", 0 }, | |
| { "adv7511w", 0 }, | |
| { "adv7513", 0 }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, adv7511_i2c_ids); | |
| static const struct of_device_id adv7511_of_ids[] = { | |
| { .compatible = "adi,adv7511", }, | |
| { .compatible = "adi,adv7511w", }, | |
| { .compatible = "adi,adv7513", }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(of, adv7511_of_ids); | |
| static struct drm_i2c_encoder_driver adv7511_driver = { | |
| .i2c_driver = { | |
| .driver = { | |
| .name = "adv7511", | |
| .of_match_table = adv7511_of_ids, | |
| }, | |
| .id_table = adv7511_i2c_ids, | |
| .probe = adv7511_probe, | |
| .remove = adv7511_remove, | |
| }, | |
| .encoder_init = adv7511_encoder_init, | |
| }; | |
| static int __init adv7511_init(void) | |
| { | |
| return drm_i2c_encoder_register(THIS_MODULE, &adv7511_driver); | |
| } | |
| module_init(adv7511_init); | |
| static void __exit adv7511_exit(void) | |
| { | |
| drm_i2c_encoder_unregister(&adv7511_driver); | |
| } | |
| module_exit(adv7511_exit); | |
| MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>"); | |
| MODULE_DESCRIPTION("ADV7511 HDMI transmitter driver"); | |
| MODULE_LICENSE("GPL"); |